· 33. secure the illuminated door sill trim harness to the vehicle frame with one wire tie with...
TRANSCRIPT
Publications No.
INSTALLATIONINSTRUCTIONS
Accessory Application
© 2017 American Honda Motor Co., Inc. – All Rights Re
VERSION 1
www.collegehillshonda.com
ILLUMINATEDDOOR SILL TRIMS P/N 08E12-TVA-100A
served. AII06720-02 (171
2018 ACCORD
0) 0
Issue Date
OCT 2017
PARTS LISTRight front illuminated door sill trim(Identification mark: R)
Left front illuminated door sill trim(Identification mark: L)
Right rear door sill trim(Identification mark: R)
Left rear door sill trim(Identification mark: L)
Illuminated door sill trim harness
Fuse label
20 Wire ties(Some may not be used)
Wire tie with clip A
Wire tie with clip B
TOOLS AND SUPPLIES REQUIRED
Diagonal cutters10 mm Open end wrenchIsopropyl alcoholPhillips screwdriverShop towelSteel wireMasking tapeThe following tools are available through the Honda Tool and Equipment Program. On the iN, click on Service > Service Bay > Tool and Equipment Program, then enter the number under “Search.” Or, call 888-424-6857.• Trim Tool Set (T/N SOJATP2014)• Plastic Trim Tool (T/N SILTRIMTL10)
1 of 178E12-TVA-1000-90
www.collegehillshonda.com
Illustration of the Illuminated Door Sill Trims on the VehicleILLUMINATED DOOR SILL TRIM HARNESS
LEFT REAR DOOR SILL TRIM
LEFT FRONT ILLUMINATED DOOR SILL TRIM2A FUSE
RIGHT REAR DOOR SILL TRIMRIGHT FRONT
ILLUMINATED DOOR SILL TRIM
INSTALLATION
Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers.”
1. Disconnect the negative cable from the battery.
2 of 17 AII06720-0
2. Remove the passenger’s dashboard under cover.
PASSENGER’S DASHBOARD UNDER COVERCLIP 2 CLIPS
3. Remove the passenger’s door sill trim.
4 CLIPS
PASSENGER’S DOOR SILL TRIM
3 RETAINING TABS
2 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
4. Pull away the door opening seal and remove thepassenger’s kick panel.
2 CLIPS
PASSENGER’S KICK PANEL
DOOR OPENING SEAL(Pull away.)
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-0
5. Release and pull up on the rear seat cushion. Place a piece of masking tape as shown to prevent the hook from re-engaging.
3 CLIPSRETAINING TAB
RIGHT REAR DOOR SILL TRIM
HOOK
1Squeeze.
Pull.2
1Squeeze.
MASKING TAPE HOLE
REAR SEAT CUSHION
6. Remove the right rear door sill trim.
2 (1710) 3 of 17
www.collegehillshonda.com
7. Remove the driver’s dashboard lower cover andunplug the vehicle connectors.
DRIVER’S DASHBOARD LOWER COVER
8 CLIPS
VEHICLE CONNECTORS
8. Lower and pull out the steering wheel as shown.
UPPER COLUMN COVER
STEERING WHEEL
MASKING TAPE
9. Apply masking tape to the upper column cover.
4 of 17 AII06720-0
10. Connect the negative cable to the battery, then turn the ignition to ON. Turn the steering wheel 90° counterclockwise. Using a plastic trim tool, release the upper column cover.
PLASTIC TRIM TOOL
UPPER COLUMN COVER
STEERING WHEEL
90° counterclockwise.
UPPER COLUMN COVER
2 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
11. Turn the steering wheel 180° clockwise. Using aplastic trim tool, release the upper column cover.
PLASTIC TRIM TOOL
UPPER COLUMN COVER
STEERING WHEEL
180° clockwise.
UPPER COLUMN COVER
12. Release the upper column cover and secure it to the dashboard with masking tape.
UPPER COLUMN COVER
DASHBOARD MASKING TAPE
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-0
13. Remove the self-tapping screw from the lower column cover.
LOWER COLUMN COVER
SELF-TAPPING SCREW
14. Turn the steering wheel 180° counterclockwise, and remove the other self-tapping screw from the lower column cover.
STEERING WHEEL
LOWER COLUMN COVER
SELF-TAPPING SCREW
180° counterclockwise.
2 (1710) 5 of 17
www.collegehillshonda.com
15. Remove the lower column cover.LOWER COLUMN COVER
SELF-TAPPING SCREW
16. Turn the ignition to OFF, then disconnect the negative cable from the battery.
17. Remove the driver’s door sill trim.
4 CLIPS
DRIVER’S DOOR SILL TRIM
3 RETAINING TABS
6 of 17 AII06720-0
18. Pull away the door opening seal and remove the driver’s kick panel.
2 CLIPS
DRIVER’S KICK PANEL
DOOR OPENINGSEAL(Pull away.)
2 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
19. Release and pull up on the rear seat cushion. Placea piece of masking tape as shown to prevent the hook from re-engaging.
1
2
Squeeze.
Pull.
HOOK
RETAINING TAB
REAR SEAT CUSHION
MASKING TAPE
1Squeeze.
HOLE
LEFT REAR DOOR SILL TRIM
3 CLIPS
20. Remove the left rear door sill trim.
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-0
21. Using isopropyl alcohol on a shop towel, thoroughly clean the fuse case where the fuse label will attach. Then, attach the fuse label (2A STEP ILLUMI) to the fuse case.
Clean with isopropyl alcohol.
FUSE LABEL (2A STEP ILLUMI) FUSE CASE
ILLUMINATED DOOR SILL TRIM HARNESS
2 (1710) 7 of 17
www.collegehillshonda.com
If the vehicle is equipped with accessory ambient lights or accessory puddle lights, go to step 23; if the vehicle is equipped with another accessory, go to step 24; otherwise, continue with step 22.Without another accessory22. Plug the illuminated door sill trim harness 6-pin
connector into the vehicle 6-pin connector. Go to step 25.
ILLUMINATED DOOR SILL TRIM HARNESS 6-PIN CONNECTOR
VEHICLE 6-PIN CONNECTOR
FUSE BOX
8 of 17 AII06720-0
With accessory ambient lights or accessory puddle lights23. Remove the dummy connector from the ambient
light or puddle light harness 6-pin connector, and plug the illuminated door sill trim harness 6-pin connector into that connector. Go to step 25.
ACCESSORY AMBIENT LIGHT HARNESS 6-PIN CONNECTOR OR ACCESSORY PUDDLE LIGHT HARNESS 6-PIN CONNECTOR
ILLUMINATED DOOR SILL TRIM HARNESS 6-PIN CONNECTOR
FUSE BOX
DUMMY CONNECTOR(if equipped)(Do not reuse.)
2 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
With another accessory (except accessory ambient lights or accessory puddle lights)24. Remove the dummy connector from the otheraccessory harness 6-pin connector, and plug the illuminated door sill trim harness 6-pin connector into that connector.
OTHER ACCESSORY HARNESS 6-PIN CONNECTORDUMMY
CONNECTOR(if equipped)(Do not reuse.)
ILLUMINATED DOOR SILL TRIM HARNESS 6-PIN CONNECTOR
FUSE BOX
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-0
25. Route the illuminated door sill trim harness along the vehicle harness, and secure it and the fuse case to the vehicle harness with two wire ties.
VEHICLE HARNESS
ILLUMINATED DOOR SILL TRIM HARNESS
FUSE CASEFUSE BOX
2 WIRE TIES
26. Route the illuminated door sill trim harness as shown, and secure it to the vehicle harness with two wire ties.
ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE HARNESS
2 WIRE TIES
DRIVER’S KICK PANEL OPENING
VEHICLE HARNESS
2 (1710) 9 of 17
www.collegehillshonda.com
If the vehicle is equipped with another accessory harness, go to step 28; otherwise, continue with step 27.Without another accessory harness27. Route the illuminated door sill trim harness as
shown. Attach one wire tie with clip A to the illuminated door sill trim harness and secure it to the vehicle bracket as shown. Go to step 29.
ILLUMINATED DOOR SILL TRIM HARNESS
DRIVER’S DASHBOARD LOWER COVER OPENING
VEHICLE BRACKET
WIRE TIE WITH CLIP A
EDGE OF THE URETHANE TAPE
10 of 17 AII06720-0
With another accessory harness28. Route the illuminated door sill trim harness as
shown. Using diagonal cutters, cut the clip portion off of the one wire tie with clip A. Secure the illuminated door sill trim harness to the other accessory harness with one wire tie with clip A.
OTHER ACCESSORY HARNESS
ILLUMINATED DOOR SILL TRIM HARNESS
EDGE OF THE URETHANE TAPE
Cut off.
WIRE TIE WITH CLIP A
DRIVER’S DASHBOARD LOWER COVER OPENING
WIRE TIE WITH CLIP A
CLIP
2 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
29. Route a piece of steel wire as shown.PASSENGER’S DASHBOARD UNDER COVER OPENING
STEEL WIRE
STEEL WIRE(Slide up.)
STEEL WIRE
STEEL WIRE
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-0
30. Attach the steel wire to the illuminated door sill trim harness with masking tape as shown.
ILLUMINATED DOOR SILL TRIM HARNESS
STEEL WIRE MASKING TAPE
ILLUMINATED DOOR SILL TRIM HARNESS
31. Route the illuminated door sill trim harness. Remove the masking tape and steel wire.
PASSENGER’S DASHBOARD UNDER COVER OPENING
ILLUMINATED DOOR SILL TRIM HARNESS MASKING
TAPE STEEL WIRE
2 (1710) 11 of 17
www.collegehillshonda.com
32. Secure the illuminated door sill trim harness to thevehicle frame at the green tape on the illuminated door sill trim harness with one wire tie as shown.
VEHICLE FRAME
WIRE TIE
GREEN TAPE
ILLUMINATED DOOR SILL TRIM HARNESS
PASSENGER’S DASHBOARD UNDER COVER OPENING
12 of 17 AII06720-0
33. Secure the illuminated door sill trim harness to the vehicle frame with one wire tie with clip B as shown. If the vehicle is already equipped with the other accessory harness, cut off the clip from that harness. Secure the illuminated door sill trim harness and other accessory harness to the vehicle frame with one wire tie with clip B.NOTE: Be careful not to damage the other accessory harness.
VEHICLE FRAME
ILLUMINATED DOOR SILL TRIM HARNESS WIRE TIE
WITH CLIP B
OTHER ACCESSORY HARNESS WITH OTHER
ACCESSORY HARNESS
CLIP(Cut off.) VEHICLE
FRAMEWIRE TIE WITH CLIP B
ILLUMINATED DOOR SILL TRIM HARNESS
2 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
34. Raise the steering wheel. Secure the illuminateddoor sill trim harness to the vehicle harness with one wire tie.
STEERING WHEEL
LOWER COLUMN COVER OPENING
ILLUMINATED DOOR SILL TRIM HARNESS
WIRE TIE VEHICLE HARNESS
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-0
If the vehicle is equipped with the another accessory harness, go to step 36; otherwise, continue with step 35.
Without another accessory harness35. Secure one wire tie to the vehicle bracket, then
secure the illuminated door sill trim harness to that wire tie with another wire tie as shown. Then, secure the illuminated door sill trim harness to the vehicle harness with one wire tie. Go to step 37.
WIRE TIE
VEHICLE BRACKET
ILLUMINATED DOOR SILL TRIM HARNESS
WIRE TIE
WIRE TIE
VEHICLE BRACKET
LOCK PORTION
FRONT
SECTION VIEW
2 WIRE TIES
VEHICLE HARNESS WIRE
TIEFUSE BOX
ILLUMINATED DOOR SILL TRIM HARNESS
2 (1710) 13 of 17
www.collegehillshonda.com
With another accessory harness36. Cut off the wire tie from the other accessory harness.Secure the illuminated door sill trim harness and other accessory harness to the wire tie on the vehicle bracket with one wire tie as shown. Then, secure the illuminated door sill trim harness to the vehicle harness with one wire tie.NOTE: Be careful not to damage the other accessory harness.
OTHER ACCESSORY HARNESS
WIRE TIE(Cut off.)
WIRE TIE OTHER
ACCESSORY HARNESS
FUSE BOX ILLUMINATED DOOR SILL TRIM HARNESS
WIRE TIE
WIRE TIE
VEHICLE HARNESS
ILLUMINATED DOOR SILL TRIM HARNESS
14 of 17 AII06720-0
37. Secure the illuminated door sill trim harness to the vehicle frame and vehicle harness with three wire ties.
ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE HARNESS
2 WIRE TIES
ILLUMINATED DOOR SILL TRIM HARNESS
PASSENGER’S DASHBOARD UNDER COVER OPENING
VEHICLE FRAME
WIRE TIE
2 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
38. Secure the illuminated door sill trim harness to thevehicle harness with three wire ties.
VEHICLE HARNESS 3 WIRE TIES VEHICLE
HARNESS
ILLUMINATED DOOR SILL TRIM HARNESS VEHICLE
HARNESSPASSENGER’S DASHBOARD UNDER COVER OPENING
39. Remove the four clips from the driver’s door sill trim, then install the clips on the left front illuminated door sill trim.NOTE: Make sure to check the identification mark before installation.
DRIVER’S DOOR SILL TRIM(Do not reuse.)
4 CLIPS
LEFT FRONT ILLUMINATED DOOR SILL TRIM(Identification mark: L)
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-0
40. Pull away the door opening seal, and peel back the carpet as shown.
CARPET(Peel back.)
CLIP
DOOR OPENING SEAL(Pull away.)
41. Position the left front illuminated door sill trim on the vehicle panel, and route the left front illuminated door sill trim harness along the vehicle harness.
LEFT FRONT ILLUMINATED DOOR SILL TRIM
VEHICLE HARNESS
VEHICLE PANEL
LEFT FRONT ILLUMINATED DOOR SILL TRIM HARNESS
2 (1710) 15 of 17
www.collegehillshonda.com
42. Plug the left front illuminated door sill trim 2-pinconnector into the illuminated door sill trim harness 2-pin connector, and secure the 2-pin connectors to the vehicle harness with one wire tie as shown.
ILLUMINATED DOOR SILL TRIM HARNESS 2-PIN CONNECTOR
VEHICLE HARNESS
WIRE TIE
2-PIN CONNECTORS VEHICLE
CONNECTORS
FRONT VIEW
Line up.LEFT FRONT ILLUMINATED DOOR SILL TRIM2-PINCONNECTOR
LEFT FRONT ILLUMINATED DOOR SILL TRIM HARNESS
FRONT
5 mm(0.20 in.)
SECTION VIEW
2 WIRE TIES
LEFT FRONT ILLUMINATED DOOR SILL TRIM HARNESS
VEHICLE PANEL LOCK
PORTIONVEHICLE HARNESSWIRE
TIEVEHICLE PANEL HOLE
WIRE TIE
VEHICLE HARNESS
TOP VIEW
43. Secure the left front illuminated door sill trim harness to the vehicle harness with two wire ties as shown.
16 of 17 AII06720-0
44. Install the carpet, driver’s kick panel, and door opening seal. Then, install the left front illuminated door sill trim on the vehicle panel.NOTE: Do not pinch the left front illuminated door sill trim harness.
LEFT FRONT ILLUMINATED DOOR SILL TRIM HARNESS(Do not pinch.)
LEFT FRONT ILLUMINATED DOOR SILL TRIM
3 RETAINING TABS
VEHICLE PANEL
DOOR OPENINGSEAL
CARPET4 CLIPS
DRIVER’S KICK PANEL
45. Remove the three clips from the left rear door sill trim, and install the clips on the new left rear door sill trim.NOTE: Make sure to check the identification mark before installation.
LEFT REAR DOOR SILL TRIM(Do not reuse.)3 CLIPS
NEW LEFT REAR DOOR SILL TRIM(Identification mark: L)
2 (1710) © 2017 American Honda Motor Co., Inc. – All Rights Reserved.
www.collegehillshonda.com
46. Lift the rear seat cushion, and install the new left reardoor sill trim on the vehicle panel. Remove the masking tape.
REAR SEAT CUSHION(Lift.)
RETAINING TAB 3 CLIPS NEW LEFT REAR
DOOR SILL TRIM
VEHICLE PANEL
MASKINGTAPE
47. Repeat steps 39 through 46 on the right side of the vehicle.
48. Check that all wire harnesses are routed properly and all connectors are plugged in.
49. Install all removed parts.50. Connect the negative cable to the battery.51. Press and hold the audio unit power button for 2
seconds to restore the audio and navi (if equipped) system functions.
52. Set the clock on vehicles without navigation.53. If necessary, restore the systems back to normal
operation as described in the service information.
Check the Operation of the Illuminated Door Sill Trims54. Make sure the lights come on when you open each
door.
© 2017 American Honda Motor Co., Inc. – All Rights Reserved. AII06720-0
2 (1710) 17 of 17