uniqueadvertising.exhibit-design-search.com€¦ · created date: 8/9/2017 1:24:29 pm
TRANSCRIPT
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX - TF-523 - Layout
SETUP INSTRUCTIONSIf you would like to tell us about your experience with your setup instructions please email us at [email protected]
Plan View
Perspective View
10’
20’
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUSTBE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions- Read entire setup instruction manual prior to unpacking parts and pieces.
- The setup instructions are created specifically for this configuration.
- Setup instructions are laid out sequentially in steps, including exploded views with detailed explanation for assembly.
WARNINGCleaning & Packing- For Cleaning Metal, Plex, & Laminate Parts: Use a MILD NON-ABRASIVE cleanser and soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat and prolonged sun exposure. Heat and UV exposure will warp and fade components.
- Retain all provided Packing Materials. All provided packing materials are for ease of repacking & component protection.
Disassembly- For loss prevention, tighten all setscrews and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS MAY BE REQUIRED
General Information
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Case 1 of 4
Case Packing - 1 of 4
Graphics
12A 11A
15A15
12 11
Setup Hardware
Halogen Lights
Top View of Each Level
Level 1
Counter Top
Plex Counter
Internal Shelf
Level 2 Level 3
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Case 2 of 4
Case Packing - 2 of 4
Graphics
Graphics
AssembledDoor
16/16A
13/13A
17A/17
18
17A/17
Top View of Each Level
Level 1
Header Graphic
Pedestal Infills (x2)
Level 2 Level 4Level 3
Base Plate (x2)
Base Plate (x2)
Base Plate
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Case 3 of 4
Case Packing - 3 of 4
Top View of Each Level
Level 1
Aer
o B
ackw
all F
ram
e B
ars
Par
ts 1
-10
Mon
itor M
ount
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Case 4 of 4
Case Packing - 4 of 4
Level 1 Level 2 Level 3 Level 4 Level 5 Level 6
Plex Counter Top Internal Shelf PedestalFront Infill
1619
5
7
5A
5
5A
1817
AssembledPedestal Side
AssembledPedestal Side
AssembledPedestal
Door
AssembledPedestal
Door
6 (x
2)
6A (x
2)
Top View of Each Level
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Step 1 of 8
Left Aero Frame Assembly
Connections are made by holding the button down and sliding the red tube into opposingtube until the connection is made. To disassemblepush button and pull or twist extrusions apart.
Push-Button
Push-Button
6 6
66
Numbered Label
Using Your Setup InstructionsThe Aero Overhead Sign Setup Instructions are created specifically for your configuration. They include an exploded view of the frame which is sequentially numbered. We encourage you to study the instructions before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-buttonconnectors and pre-connected horizontal sections.
Cleaning and Packing Your Display1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood of shipping damage.
1
2
3
4
5
6
7
89
10
Steps:1) Assemble Aero Frame in numerical order.2) Install Nylon Insert to base plate [1] using a screw.2) Attach base plate to assembled backwall.3) Slip pillowcase graphic over assembled frame. NOTE: Do with care to prevent ripping.
Nylon Insert forAero Frame
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Step 2 of 8
Backwall Assembly
1A
1A
11
11A
12
13
13A
12A
Item1A
11/11A12/12A13/13A
Qty.2
1/11/11/1
DescriptionBase Plate47.5”h S44 Vertical Extrusion47.5”h S44 Vertical Extrusion26”w Z45 Horizontal Extrusion
Steps:1) Connect verticals [11] & [11A] together. See S44 Connector detail. Repeat step for assembling verticals [12] & [12A].2) Install Nylon Insert to base plates [1A] using a screw through the outer hole.3) Attach base plates [1A] to the bottom of verticals [12/12A] & [11/11A].4) Connect horizontals [13] & [13A] between veritcal assembies [11/11A] & [12/12A].5) Attach assembled Aero Frame (with pillowcase graphic installed) to key hole located in [11A]. See Aero Frame to Vertical Extrusion Attachment detail.
BACK SIDE
Screw
s
Connector
S44 Connector
Silde extrusion over connector and rest onlower vertical; secure with screws.
**To prevent product loss, Keep all screws attached to connector piece after disassembling
*
Nylon Insert forAero Frame
Nylon Insert forAero Frame
* *
Key Hole is ongroove closest to exterior of exhibit.
Aer
o G
raph
ic F
ram
e
Insert bolts of aero frame into keyhole slote in groove of vertical extrusion, slide aero frame down to secure.
Aero Frame to VerticalExtrusion Attachment
Bolt Attachedto Aero Frame
*
V20 Connector
*
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Step 3 of 8
14
15
16
16A
Sid
e In
fill
Sid
e In
fill
17
17
17A17A
18
Item1415
16/16A17/17A
18
Qty.11
1/12/21
Description37.25”h S44 Vertical Extrusion w/ Door Stop37.25”h S44 Vertical Extrusion w/ Door Hinges26”w Horizontal Extrusion12”w Horizontal Extrusion29.622”w Mounting Plate
Steps:1) Attach horizontals [16] & [16A] between verticals [14] & [15]. NOTE: Install [16] at the base of door stop; Install [16A] at to top of door stop.2) Connect horizontals [17] between verticals [14] & [15] and backwall verticals [11].3) Insert Side Infills between verticals [14] & [15] and backwall; secure with horizontals [17A].4) Place cabinet bottom inside assembled kiosk frame. NOTE: Shelf will rest on lips of horizontals [17].5) Assemble Plex & Wood counters together. See Plex Counter Attachment detail.6) Install assembled counter top to assembled kiosk base. See Counter Top Attachment detail.7) Hang door on hinges located on vertical [15]. See Door Attachment detail.8) Attach monitor mounting plate [18] to verticals [11A] & [12A]. See Monitor Mount Attachment detail. 9) Install header Graphic. NOTE: Will attach using Velcro
Plex Counter Attachment*Attach stand-off barrels to primarycounter top.Connect plexcounter to primarycounter top usingscrew caps.
**DO NOTOVER TIGHTEN. PLEX WILL CRACK**
Screw Cap
Plex Counter
Align hole with pin Rotate pin. Springwill push pin into hole.
Counter Top Attachment
1 2*
DoorHinge
Hinge
Slide pin intohinge attachedto vertical. Slide doorhinge over pin.
Door Attachment*
* *
*
*
** *
*
*
Monitor Mount Attachment
Attach mounting plateto verticals as shown.
Then attach wall plate to plate using bolts & wing nuts
Slide mounting connectorscenter into groove. Tightensetscrew to secure in place.
Setscrew
Setscrew
*
1
2
3
Backwall Workstation Assembly
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Step 4 of 8
Right Aero Frame Assembly
Connections are made by holding the button down and sliding the red tube into opposingtube until the connection is made. To disassemblepush button and pull or twist extrusions apart.
Push-Button
Push-Button
6 6
66
Numbered Label
Using Your Setup InstructionsThe Aero Overhead Sign Setup Instructions are created specifically for your configuration. They include an exploded view of the frame which is sequentially numbered. We encourage you to study the instructions before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-buttonconnectors and pre-connected horizontal sections.
Cleaning and Packing Your Display1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood of shipping damage.
19
20
21
28
31
32
30
29
27
22
24
25
26
23
1
1
Steps:1) Assemble Aero Frame in numerical order2) Attach Nylon Inserts to base plates using screws.2) Attach base plates to assembled backwall.3) Slip pillowcase graphic over assembled frame. NOTE: DO with care to prevent ripping.
Nylon Insert forAero Frame
Nylon Insert forAero Frame
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Step 5 of 8
Backwall Assembly Cont.
12A
Nylon Insert forAero Frame
*
Key Hole is ongroove closest to exterior of exhibit.
Aer
o G
raph
ic F
ram
e
Insert bolts of aero frame into keyhole slote in groove of vertical extrusion, slide aero frame down to secure.
Aero Frame to VerticalExtrusion Attachment
Bolt Attachedto Aero Frame
*
V20 Connector
1) Attach assembled Aero Frame (with pillowcase graphic installed) to key hole located in [12A]. See Aero Frame to Vertical Extrusion Attachment detail.
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Step 6 of 8
Light Attachment
Steps:1) Attach lights in desired location on top rails of backwall. See Light Attachment detail.
Light ConnectionAttach lights tobackwall wheredesired and tighten in place.
*
*
**
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Step 7 of 8
MOD-1371 - Assembly
Whenassembled
Steps:1) Attach base [1] to post using bolt.2) Attach square plates [4] to curved vertical using bolts. NOTE: Square plate [4] must rotate to left and right before installing clamshell.3) Attach clamshells [5] to square plates [4] using hex nuts. 4) Insert iPad and feed wire through holes as shown in detail.
Base
Mount
WireAccess
iPad
Lock
Lock
Foam LiningRemoved
Home Button Shield
Optional Cover for Home Button
Clamshell Attachment
Baseplate Attachment
1) Remove foam lining from inside bottom of clamshell as shown.2) Attach Home Button Shield with double-sided tape to inside of clamshell, keeping top of shield flush with clamshell opening as shown.NOTE: This is a permanent fix and can’t be easily removed.
Rotate clamshellto turn iPad from portrait to landscape orientation
Post Rotates vertically
HexNuts
© 2017
www. c l a s s i c e x h i b i t s . c om
Order #XXXXX -
Step 8 of 8
Reception Counter Assembly
1
2
34
5
56
Cabinet Bottom
Infill
InfillInfill
6
When Assembled
Front View
Item1234
5/5A6/6A
Qty.1111
2/22/2
Description37.25”h Vertical Extrusion w/ Door Hinges37.25”h Vertical Extrusion w/ Door Stop37.25”h Vertical Extrusion 37.25”h Vertical Extrusion16”w Horizontal Extrusion33.7757”w Horizontal Extrusion
Steps:1) Attach horizontal extursions [5] between verticals [2&3] & [1&4].2) Connect horizontals [6] between verticals [1&2] & [3&4]; place Cabinet Bottom self onto lip of horizontals.3) Insert side Infills between verticals [2&3] & [1&4]; insert front Infill between verticals [3&4].4) Hang Assembled Cabinet Door. See Door Attachment detail. 5) Attach horizontal extrusions [5A] between verticals [2&3] & [1&4].6) Connect horizontals [6A] between verticals [3&4]; place Cabinet Top onto lip of horizontals. 7) Screw threaded end of Stand-off Barrels into the tops of verticals.8) Place Upper Plex Counter on top of installed barrels; secure with screw caps. See Upper Plex Counter Attachment detail.
1) Attach standoff barrels to counter and secure in place.
2) Secure Upper Plex Counter to standoffs using screw caps.
Upper Plex Counter Attachment
Upper PlexCounter
StandoffBarrel
ScrewCap *
DoorHinge
Hinge
Slide pin intohinge attachedto vertical. Slide doorhinge over pin.
Door Attachment*
Cabinet Top
5A
AssembledDoor
AssembledDoor
5A
6A
7
6A
BACKVIEW
*
*
UpperPlex Counter