€¦ · 01| pneumatic cylinder reference data [1] - 2 mini pin cylinder / ajp [1] - 14 guide unit...

Pneumatic Cylinder01|

Reference Data [1] - 2

Mini Pin Cylinder / AJP [1] - 14

Guide Unit / KGUA [1] - 16

Small Pin Cylinder / ACP [1] - 18

Direct Mount Type Cylinder / ACD [1] - 26

Small Cylinder (AL Tube) / ACS2 [1] - 28

Small Cylinder (SUS Tube) / ACS3 [1] - 42

Small Cylinder (AL Tube/Air Cushion) / ACS4 [1] - 54

Small Cylinder (SUS Tube/Air Cushion) / ACS5 [1] - 58

Round Cylinder / ACR [1] - 62

Medium Cylinder / ACM [1] - 65

Large Cylinder / ACL [1] - 78

Extra-Large Cylinder / ACX [1] - 96

Low Friction Cylinder / KLC [1] - 100

Labyrinth Cylinder / KLCS [1] - 102

Compact Cylinder / AF, ADF [1] - 104

Compact Guide Cylinder / AFG [1] - 127

Free Mount Cylinder / FM, FMD [1] - 132

Custom-Made Rod Ends [1] - 135

Custom-Made Tie Rods [1] - 137

Booster Cylinder / KBP [1] - 138

Air-Hydro Converter / CCTS [1] - 142

KCC Co., Ltd.

www.kccpr.com21 -

PNEUMATIC & HYDRAULIC Pneumatic Reference Data

Pneumatic System

Adjust air flow rate.

Reduce exhaustion

noise

Change air flow direction

Move an object.

Rotary Cylinder

Speed Controller

Silencer

One-touch Joint

Tube

Air Gun

Air Solenoid ValveCylinderValveCylinder

ActuatorSpeed Control Valve

Suppliment Control Equipment(Directional control valve)

When using a pneumatic device, it is important to select and to apply every single device appropriately according to its applications. With reference to the following selection factors, select and design a suitable pneumatic system according to its applications.

Cylinder Selection

Item Select a pneumatic system regarding to kind of operation

Main factor What kind of operation

Sub factorControl

pneumatic circuit

Use pneumatic

tools

Control air ow

Control movement Others

Main equipment

Control equipment

Control equipment

Control equipment

Actuator,Control

equipment,Supplementary

equipment

-

Select a pneumatic system regarding toair quality

Quality of air

Lubricated type

Cleanliness

Regulator

Generator

Non-lubricated type

Cleanliness

Regulator

Generator

KCC Co., Ltd.

www.kccpr.com 31 -

Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Pneumatic System

Adjusting Equipment Generator

What Is Air Pressure?There are different types of pressure unit, but International System of Units (SI units) is the most widely used unit. The absolute pressure is measured relative to the absolute zero pressure (the pressure that would occur at absolute vacuum). While gauge pressure is the pressure relative to the local atmospheric or ambient pressure. Gauge pressure kgf/cm2(bar) is used in this catalogue.

Absolute pressure = Gauge pressure + atmospheric pressure = Pressure indicated on pressure gauge + 1.033

1.033

1.013

14.7

760

0.101

1.0330

0 5

0 50

0

0

0

100

5

5

5

0.5

5000

9.8

9.7

0.98

10

142

7356

10

11.033

Negative pressure(Vacuum)(Unit)

Highpressure

Positive pressure

kgf/cm2

kgf/cm2

abs

MPa

mmHg

atm

bar

Psi

Absolute Pressure

Gravitation System of Units

OtherSystem of Units

InternationalSystem of Units

Gravitation System of Units

KCC Co., Ltd.

www.kccpr.com41 -


Theoritical Output

Relation Between Cylinder Output & Pressure

Cylinder output force can be found by knowing tube's bore size, piston rod diameter and air pressure. In general, pressure coef cient is depending on sliding resistance of cylinder packing and friction resistance of metal rod. But the load factor of theoritical output is set 0.7 or less generally.In case of fast speed is required, load factor of theoritical output should be set as 0.5 or less. Following is the formula of theoritical force.

F1 : Extension theoritical force (kgf)

F2 : Retraction theoritical force (kgf)

P : Working pressure (kgf/cm2)

D : Bore size (cm)

d : Piston rod diameter (cm)

1 : Friction coef cient (Extension)

2 : Friction coef cient (Retraction)

W1 : Extension cylinder output (kgf)

W2 : Retraction cylinder output (kgf)

Friction Coef cient

0.75Ø40

Ø50

Ø80

Ø63

Ø100이상

F1 = × D2 × P4

F2 = × (D2 - d2) × P4

W1 = 1 × F1

W2 = 2 × F2

Pressure

Pressure

Fric

tion

Coe

f ci

ent

Wei

ght-P

ress

ure

Coe

f ci

ent

& above

KCC Co., Ltd.

www.kccpr.com 51 -

Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Theoritical Output

Bore size (mm)

Rod dia.(mm)

Operating direction

Pressurized area

Working pressure (kgf/cm2)

2 3 4 5 6 7 8 9 10

6 3 OUT 0.283 0.57 0.85 1.13 1.41 1.70 1.98 - - -IN 0.212 0.42 0.64 0.85 1.06 1.27 1.48 - - -

10 5 OUT 0.785 1.57 2.36 3.14 3.93 4.71 5.50 - - -IN 0.589 1.18 1.77 2.36 2.95 3.53 4.12 - - -

15 6 OUT 1.767 3.53 5.30 7.7 8.84 10.60 12.37 - - -IN 1.484 2.97 4.45 5.94 7.42 8.91 10.39 - - -

16 5 OUT 2.01 4.02 6.03 8.04 10.1 12.1 14.1 - - -IN 1.81 3.62 5.43 7.24 9.05 10.9 12.7 - - -

20 10 OUT 3.14 6.28 9.42 12.57 15.71 18.85 22.0 15.1 28.3 31.4IN 2.36 4.71 7.07 9.42 11.78 14.14 16.49 18.85 21.2 23.6

25 12 OUT 4.91 9.82 14.73 19.693 24.5 29.4 34.4 39.3 44.2 49.1IN 3.78 7.56 11.33 15.11 18.89 22.7 26.4 30.2 34.0 37.8

30 12 OUT 7.07 14.14 21.2 28.3 35.3 42.4 49.5 56.5 63.6 70.7IN 5.94 11.88 17.81 23.8 29.7 35.6 41.6 47.5 53.4 59.4

32 12 OUT 8.04 16.6 24.1 32.2 40.2 48.3 56.3 64.3 72.4 80.4IN 6.91 13.8 20.7 27.6 34.6 41.5 48.4 55.3 62.2 69.1

40 16 OUT 12.57 25.1 37.7 50.3 62.8 75.4 88.0 101 113.1 125.7IN 10.56 21.1 31.7 42.2 52.8 63.3 73.9 84.4 95.0 105.6

50 20 OUT 19.63 38.3 58.9 78.5 98.2 117.8 137.4 157.1 176.7 196.3IN 16.49 33.0 49.5 66.0 82.5 99.0 115.5 131.9 147.4 146.9

63 20 OUT 31.2 62.3 93.5 124.7 155.9 187.0 218 249 281 312IN 28.0 56.1 84.1 112.1 140.2 168.2 196.2 224 252 280

80 25 OUT 50.3 100.5 150.8 201 251 302 352 402 452 503IN 48.5 90.7 136.1 181.4 227 272 317 363 408 454

100 30 OUT 78.5 157.1 236 314 393 471 550 628 707 785IN 71.5 142.9 214 286 357 429 500 572 643 715

125 35 OUT 122.7 245 368 491 615 736 859 982 1104 1227IN 112.5 225 338 450 563 675 788 900 1013 1125

140 35 OUT 153.9 308 462 616 770 924 1078 1232 1385 1539IN 143.8 288 431 575 719 863 1006 1150 1294 1438

150 40 OUT 176.7 353 530 706 883 1060 1236 1413 1590 1767IN 167.1 334 501 668 835 1002 1169 1336 1503 1671

160 40 OUT 201 402 603 804 1005 1206 1407 1608 1810 2011IN 188.5 377 565 754 942 1131 1319 1508 1696 1885

180 45 OUT 254 509 736 1018 1272 1527 1781 2036 2290 2545IN 239 477 716 954 1193 1431 1670 1909 2147 2396

200 50 OUT 314 628 942 1257 1571 1885 2199 2513 2827 3142IN 295 589 884 1178 1473 1767 2062 2356 2651 2945

250 60 OUT 491 982 1473 1963 2454 2945 3436 3927 4418 4909IN 463 925 1388 1850 2313 2776 3238 3701 4163 4626

280 70 OUT 615.4 1230.8 1846.2 2461.6 3077 3692.4 4307.8 4923.2 5538.6 6154IN 576.9 1153.8 1730.7 2307.6 2884.5 3461.4 4038.3 4615.2 5192.1 7569

300 70 (75)OUT 707 1414 2121 2827 3534 4241 4948 5655 6362 7069IN 668

(662.3)1337

(1324.6)2005

(1986.9)2673

(2649.2)3342

(3311.5)4040

(3972.8)4679

(4636.1)5347

(5298.4)6015

(5960.7)6684

(6623)350 85 OUT 961.6 1923.2 2884.8 3846.4 4808 5769.6 6731.2 7692.8 8654.4 9619

IN 904.9 1809.8 2714.7 3619.4 4524.5 5429.4 6334.3 7239.2 8144.1 9049400 100 OUT 1256 2512 3768 5024 6280 7536 8792 10048 11304 12560

IN 1177.5 2355 3532.5 4710 5887.5 7065 8242.5 9420 10597.5 11775450 100 OUT 1589.6 3179.2 4768.8 6358.4 7948 9537.6 11127.2 12716.8 14306.4 15896

IN 1494.6 2989.2 4483.8 5978.4 7473 8967.6 10462.2 11956.8 13451.4 14946

Double Acting Cylinder

Bore size (mm)

Rod dia.(mm)

Operating direction

Pressurized area

Working pressure (kgf/cm2)

2 3 4 5 6 7 8 9 10

2.5 1 OUT 0.049 - 0.03 0.08 0.13 0.174 0.223 - - -IN - 0.06

4 2 OUT 0.126 - 0.10 0.22 0.35 0.47 0.60 - - -IN - 0.15

6 3 OUT 0.283 0.17 0.45 0.73 1.0 1.3 1.6 - - -IN - 0.15

10 4 OUT 0.785 0.94 1.7 2.5 3.3 4.1 4.9 - - -IN - 0.25

15 5 OUT 1.767 2.1 3.9 5.7 7.4 9.2 11.0 - - -IN - 0.45

16 5 OUT 2.01 2.6 4.61 6.62 8.68 106 12.7 - - -IN - 0.7

20 10 OUT 3.14 2.1 5.2 8.4 12 15 18 21 24 27IN - 0.9

25 12 OUT 4.91 4.5 9.4 14 19 24 29 34 39 44IN - 1.0

30 12 OUT 7.07 6.6 14 21 28 35 42 49 56 63IN - 1.5

40 18 OUT 12.57 16 29 42 54 67 79 92 104 117IN - 2.0

Single Acting Cylinder (Spring Return)

Theoritical force of a single acting cylinder during extension is the value of theoritical force of double acting cylinder subtract spring tension. While theoritical force of single acting cylinder during retraction is the value of spring tension.

Do not apply load to piston rod during retraction.

KCC Co., Ltd.

www.kccpr.com61 -


Air Consumption

Air Consumption Calculation

Air consumption can be found by knowing the volume of cylinder and piping volume between cylinder and valve.

How to Read Graph

Tube volume is varies depending on the ways of piping. Therefore, only cylinder air consumption is calculated.

Air Consumption of Cylinder & Tube

Q = (A1 + A2)L × (P + 1.033)N1000

Q: Air consumption ( /min)P: Working pressure (kgf/cm2)L: Stroke (cm)N: Number of reciprocation per min

A2 = (D2 -d2)4

A2: Rod side piston aread: Rod diameter(cm)

A1 = × D2

4

A1: Head side piston areaD: Tube bore size(cm)

How to read graph

Cylinder air consumption N /min

Example

Cylinder stroke x Number of reciprocation per minute (mm/min) orLength of tube x Number of piston reciprocation per minute.

Example

Working pressure kgf/cm2

Tube

bor

e si

ze

mm

Tube

type

Working pressure kgf/cm2

Example

For cylinder bore size is 40mm, stroke is 100mm, working pressure is 5kgf/cm2, number of piston reciprocation per minute is 5. Cylinder air consumption = Cylinder stroke x Number of piston reciprocation per minute. = 100 × 5 = 500 mm/min or 8N /min Example

For cylinder bore size is 40mm, stroke is 100mm, working pressure is 5kgf/cm2, number of piston reciprocation per minute is 5, and cylinder is connected to a 6mm-diameter nylon tube with 2m length.Cylinder air consumption = length of tube x Number of piston reciprocation per minute. = 2000 × 5 = 1000 mm/min or 3N /min

KCC Co., Ltd.

www.kccpr.com 71 -

Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Symbol

SymbolSymbol Type Remarks

Flow line

Line connection

Distance between lines of shafts or lever rod.

Energy conversion unit, Pump, Compressor,

Motor

Measuring devices

Rotating joint of check valve

Link joint roller

Valve

L > 10EL > 5EL : Line length E : Line weigth

d : Diameter of black dotE : Line weight

Symbol Type Remarks

Flow directionFlow inlet port or

exhaust port

Black triangle indicates liquid state fluid, while white triangle indicates

gas state fluid.

Indication of flow direction

Indication of rotation

Filter, separator, lubricator, heat

exchanger

Assembly unit

Indication of the possibility of adjustment

Symbol Type Remarks Symbol Type Remarks

Single acting cylinder

without spring

Double acting cylinder

single rod

Single acting cylinder

without spring

Double acting cylinder

double rod

Single adjustable

cushion cylinder

Double adjustable

cushion cylinder

(1) Detail symbol(2) Simplified symbol




indicate adjustable type

Differential cylinder

Telescopic cylindersingle acting

Double acting

Diaphragm type cylinder

Pressure converter(Same fluid)

Pressure transmitters

Ram cylinder

Pressure converter(Different fluid)

KS B 0054-82, JIS B 0125-1972

(1)

(2)

(1)

(2)

(1)

(2)

(1)

(2)

(1)

(2)

(1)

(2)

(1)

(2)

(1)

(1)

(2)

(2)

(3)

Size of those circles are differentiate in large, medium and small in

drawing diagram.

KCC Co., Ltd.

www.kccpr.com81 -


Pneumatic Cylinder

Structure Classi cation

Type Features

Mounting Style Classi cation

Single Acting Cylinder(Single rod)

Single Acting Cylinder(Double rod)

Double Acting Cylinder(Single rod)

Double Acting Cylinder(Double rod)

Stroke Adjustable Cylinder

Dual Stroke Cylinder(Single rod)

Dual Stroke Cylinder(Double rod)

Tandem Cylinder

Cylinder in which the air acts on one side of the piston only, normally piston is returned by spring force or weight.

Cylinder which the working fluid acts alternately on both sides of the piston. It is a most common type cylinder.

Cylinder with a variable stopper to adjust stroke.

Cylinder with 2 strokes. It has the same function as adjusting 2 cylinders.

Cylinder with multiple pistons. Tandem cylinder with "N" pistons produces "N" times force.

Standard Type (B)

Foot Type (LB)

Flange Type(FA, FB)

Cylinder without any mounting bracket.

Foot bracket attached cylinder, which moves load in horizontal direction.

Flange bracket attached cylinder, which moves load in vertical direction.

Rod side flange(FA)

Head side flange (FB)

KCC Co., Ltd.

www.kccpr.com 91 -

Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

PNEUMATIC & HYDRAULIC

Type Features

Pneumatic Reference Data

Pneumatic Cylinder

Clevis Type(CA, CB)

Trunnion Type (TC)

Cylinder with a pin hole at the right angle direction of rod centerline. Cylinder with single clevis mount or double clevis mount with allow rotation.

Cylinder with a pin at the right angle direction of rod centerline. Cylinder with pin at the middle is called center trunnion type cylinder. The cylinder allows angular movement.

Note) Figures inside "( )" indicates KS Standard classi cations.

Pneumatic Cylinder Parts

Piston : It should be strong, abrasion resistance and seizure resistance. Generally, grey cast iron material is used for its excellent slide characteristics.

When light weight is required, plastic or AL alloy wearing is used.

Piston rod : Alloy steel S45C or above class is used, plated by hard Cr, with a surface roughness of 1.6S, wear resistance and abrasion resistance.

Buckling and bending should be considered when design process is carry on.

Cylinder tube : To prevent wear of inner tube, it required 20 hard plating or hard coating and 1.6S of surface roughness.

Cover : Part for rod bush and sealing packing is attached as well as the air port size adjusting part.

Tie rod : Fix both of the cover(head side cover and rod side cover)

Rod bush : Lateral load applied on piston rod is supported by rod bush and lateral load must be within 1/20 of max. cylinder output.

SEAL :

1) Fixing type : O-Ring (NBR)

2) Moving type : Squeeze packing, moving o-ring, lip packing, wiper ring, dust seal and etc.

Squeeze packing: When pressue is applied, the expansion force of the paking form a contact pressure to seal.

Lip packing: When pressue is applied onto the lip(bending part) and make the bending lip become straight and contact to the inner tube

surface to seal.

Single Clevis (CA)

Double Clevis (CB)

Center Trunnion(TC)

KCC Co., Ltd.

www.kccpr.com101 -


Work piece feeding

Snap-ring fastening

Cylinder

Feeding

Auto open/close Press

Direction change Return

Gate open/close Assembly

Cylinder

Workpiece

Cylinder


Application of Pneumatic Cylinder

Applications

KCC Co., Ltd.

www.kccpr.com 111 -

Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Precautions

LB, FA, FB MountUse washer when fastening bolt to cylinder to prevent loosening.

Do not apply any unnessary load to mount and avoid improper installation.

Do not apply eccentric load or lateral load to cylinder rod.

LB Mount

CA, CB, TC Mount (Angular Movement)For stroke 1000mm or above, horizontal installation is not recommended.

TC Mount

Load

Load

Load

Load

Retraction with load

Extension with load

FA

FA

FB

FB

KCC Co., Ltd.

www.kccpr.com121 -


Precautions


1. Do not hit or apply excessive impacts on to cylinder.

2. Flush (with air) or wash to remove chips, cutting oil and other debris from pipe before piping is connected.

3. Be certain to align the rod axis with the load and direction of movement when connecting.

(When it is necessary, use a oating joint to prevent eccentric)

Notes on Installation

Notes on Use 1. Check the puri cation system regulary to ensure clean uid is used.

2. Use Turbine oil class 1(ISO VG32) for lubricated type cylinder.

3. Do not discontinue to lubricate once if you lubricate it.

4. Do not scratch or gouge the sliding parts of the cylinder tube or piston rod. (May lead to seal damage and cause air leakage)

5. Install a special device to protect rod if the cylinder is using under a poor conditions (which is full with dust or spark)

Notes on Maintenance 1. Check cylinder mounting nut and bolt from become loose.

2. Check mounting bracket of cylinder from getting loose or etc.

3. Check cylinder operating condition.

4. Check the change of speed of cylinder with time.

5. Check air leakage and scratch on rod surface.

6. Check rod end accessory, tie rod or bolt from getting loose.

In uences of Foreign Substaince 1. Clog of path of lter element cause pressure drop.

2. Weaken the exhaustion performance of lter drain.

3. Cumulative foreign substaince on ow path decrease ow rate.

4. Cumulative foreign substainceon operating part can cause malfunction.

5. Corrosion can cause malfunction.

6. Exceeded friction can cause damage to seal and diaphragm.

7. Malfunction of solenoid valve

KCC Co., Ltd.

www.kccpr.com 131 -

Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Cause s & Resolve of Trouble


Even though seal material, surface treatment, electrical material, electronics technology has been remarkably improved and product have a longer service life with higher reliability and less failure rate compare with conventional product. However, constant occurrence of trouble is still considerable.

Pneumatic is easy to handle and maintenance. However, without understanding of the nature of compressibility characteristic of air as a working uid in pneumatic system might cause an unexpected accident.

Different kinds of trouble examples of following pneumatic devices are shown below Pneumatic cylinder, Air hydro cylinder, Rotary actuator, Pressure transmitter Solenoid valve, Speed controller, Reducing valve, Auto switch Air generator, Air compressor, Compressed air quality Lubrication, Safety

Explain the trouble which happen commonly and explain the causes and resolves by giving examples, so that it is easy to be understood even for a beginner.

Among pneumatic devices, trouble mostly happen on pneumatic cylinder and solenoid valve. Following are the details about cylinder and solenoid trouble.

(1) Air Source (Air Compressor)Lack of air suppy is a common trouble for air generator. Therefore, select an air compressor with suitable air capacity and select an air tank or change the pipe size might solve the problem.

The degradation of air compressor, after cooler performance and other devices or re accident can be prevented by having maintenance regularly.

(2) PipingImproper piping method can cause critical pressure drop or draining. Mixing of chips, cutting oil and other debris can also cause a problem.

To prevent these troubles from happening for better durability, it is assential that user has to learn a proper piping technic and connect the pipe carefully.

(3) Air quality and LubricationDuring air compression, drain problem can not be avoided. Thus, a countermeasure is necessary. Auto drain, air dryer and other devices are used to prevent freezing.Regarding lubrication oil. Improper handing of lubricator or fault maintenance can cause lubrication insuf ciency problem. Learing lubricating technic, applying non lubricated combination can increase service life and rust resistance.

(4) Pneumatic CylinderInadequate pneumatic circuit might cause risk such as cylinder runaway or can not do emergency stop (because of air pressure compressibility). For those trouble, user should have a deep understanding about the relation between load factor of pneumatic cylinder and its operation. Besides, there are other troubles such as piston rod damage or packing damage. These troubles can be avoided by appropriate pneumatic circuit design, usage and installation.

(5) Solenoid ValvePilot type solenoid valve common troubles: insuf cient pilot pressure, malfunction caused by control valve.Direct acting type solenoid valve common troubles: Coil burnout accident caused by inproper spool operationSolenoid has a lot of trouble when associated with methods or environments such as wiring, rain water, temperature and etc.

(6) Notes on safetyInadequate pneumatic circuit might cause risk such as cylinder runaway or emergency stop failure (due to air pressure compressibility)

Thus, application of a proper pneumatic circuit is essential to prevent accident like dropping of workpiece or hand injured by machine when electricity cut off occur.

KCC Co., Ltd.

www.kccpr.com 141 -


Mini Pin Cylinder

AJP series

AJP series

AJP - B 10 - 15 -

Bore size6 6mm

10 10mm15 15mm

Hose nipple (Option)Nil None (Standard)H4 For tube Ø4-2.5 H6 For tube Ø6-4

Rod end threadNil With threadB Without thread

Cylinder stroke5 5mm

10 10mm15 15mm

Unit :N

Bore size Stroke (mm) 0 Stroke Stroke end

Ø6 5, 10, 15 3.92 1.47

Ø10 5, 10, 15 5.98 2.45

Ø15 5, 10, 15 10.79 4.41

Same spring force for all stroke.

Applicable tube size Model

Ø4-2.5 N4M5

Ø6-4 N6M5

Unit :g

ModelStroke (mm)

5 10 15

AJP-B6 10.6 13.1 15.6

AJP-B10 28 33 38

AJP-B15 72 82 92

How to Order

Speci cations

Spring Retracting Force

Mass

Hose Nipple For Panel Mount Style

SeriesAJP Mini pin cylinder

Features

Short-stroke cylinder designed with a shorter overall length than a conventional cylinder. Space saving pin cylinder for

panel mounting. It miniaturizes the size of mechanical devices.

Symbol

Single Acting /Spring Return

Weight of hose nipple (4g) is not included.

Action Single acting spring return

Fluid Air

Proof pressure 10.5kgf/cm2 (1.05MPa)

Max. operating pressure 7kgf/cm2 (0.7MPa)

Min. operating pressure

Ø6 2kgf/cm2 (0.2MPa)Ø10, Ø15 1.5kgf/cm2 (0.15MPa)

Ambient & fluid temperature 5 ~ 60

Operating piston speed 50~500mm/s

Cushion None

Lubrication Not required

Tolerance of stroke +1.00

Tolerance of thread KS class 2

Mounting style Panel mounting

Accessory Mounting nut 2 pcsRod end nut 2 pcs (Rod end thread type)

KCC Co., Ltd.

www.kccpr.com 151 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Mini Pin Cylinder

AJP series

Unit : mm

Bore size A B C EF

ØG H K MM NN RS

WZ

ØQ5ST 10ST 15ST 5ST 10ST 15ST 5ST 10ST 15ST

Ø6 7 12 13.9 6 12.5 19.5 26.5 8.5 9 3.5 M3X0.5 M10X1.0 9 18.5 25.5 32.5 3 27.5 34.5 41.5 3

Ø10 10 19 22 6 14.5 21 28 12 12 3.5 M4X0.7 M15X1.5 13 20.5 27 34 4 32.5 39 46 5

Ø15 12 27 31 7 16.5 22.5 29 19 14 4.2 M5X0.8 M22X1.5 20 23.5 29.5 36 5 37.5 43.5 50 6

Part no. Parts Material Remark

1 Cover Brass Electroless Nikel Plating

2 Piston Stainless Steel -

3 Collar Sintered Metal Bronze

4 Return Spring Steel Wire Zinc Chromate

5 Piston Packing NBR -

6 Mounting Nut Brass Electroless Nikel Plating

7 Rod End Nut Steel Nikel Plating

Unit : mm

Part no. Applicable bore size d H B C

AJP-SN06 Ø6 M10×1.0 3 12 13.9

AJP-SN10 Ø10 M15×1.5 4 19 22AJP-SN15 Ø15 M22×1.5 5 27 31

Unit : mm

Part no. Applicable bore size d H B C

AJP-RN06 Ø6 M3×0.5 1.8 5.5 6.4

AJP-RN10 Ø10 M4×0.7 2.4 7 8.1AJP-RN15 Ø15 M5×0.8 3.2 8 9.2

Dimensions

Structure Dimensions-Accessory

7

36 1 4 2

5

d

B

C

H

d

B

C

H

H

ØQ

Ø6: C0.5Ø10,15: C1

B

R

C

M5×0.8

ØG

MM

A

H

Z

W

S

F E

NN

Mounting Nut

Rod End Nut

Material: Brass

Material: Carbon Steel

Rod end without thread.

KCC Co., Ltd.

161 -


www.kccpr.com

Guide Unit

KGUA series

KGUA series

KGUA 20 - 100

SeriesKGUA Guide unit for cylinder

Bore size of applicable cylinder10 Ø1016 Ø1620 Ø2025 Ø2532 Ø3240 Ø40

How to Order

KGUA 20-100

Cylinder not included.

Cylinder strokeBore size Standard stroke

Ø10 5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75, 100, 125, 150

Ø16 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75, 100, 125, 150, 175, 200

Ø20 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450,

500, 550, 600Ø25

Ø32

Ø40 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 600

Other intermediate strokes available on request.

MassUnit : kg

Bore size (mm) Ø10 Ø16 Ø20 Ø25 Ø32 Ø40

Basic mass 0.17 0.26 0.33 0.59 0.64 1.24Additional mass of each 50mm stroke 0.06 0.09 0.16 0.25 0.26 0.41

Features

Smooth and precise movement. Excellent appearance and easy to mount. Can be combined with various cylinders. Adoption of advanced material in non-

lubricated bearing

1. Care must be taken to avoid injuries or damage arising from an object being crushed or pressed against the sliding part on the guide rod.2. The surface of the guide rod is made with a high degree of precision, therefore a slight deformation or scar may cause malfunction or impaired durability.3. If a guide body is tted, the tting surface thereof should have a high degree of atness.4. A distorted or bent guide rod may cause abnormal increase in operational resistance and early wear on the bearing, resulting in impaired performance.5. Fit on the place in contemplation of easy maintenance. Secure suf cient space around the cylinder for easy maintenance.6. Do not move the back plate to adjust strokes. It may cause poor impact absorption when the back plate comes in contact with the guide body or the bolt xing the bracket, resulting in improper stroke positions and operation.

Precautions

Calculation:

Ex) KGUA 32-500 Basic mass: 0.64(32Ø) / Additional mass: 0.26/50 / Stroke: 500mm 0.64+(0.26/50X500) = 3.24kg

KCC Co., Ltd.

171 -


www.kccpr.com

Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Guide Unit

KGUA series

Part no. Parts Material

1 Guide Body Aluminium Alloy

2 DU Bush -

3 Guide Rod Steel

4 Back Plate Aluminium Alloy

5 Front Plate Steel

6 Bolt For Guide Carbon Tool Steel

7 Flat Washer -

8 Rod End Attachment Carbon Steel

Structure

1 2 3

4

5

6

7

8

Unit : mm

Model A B C D1 D2 E1 E2 F1 F2 G H1 H2 H3 H4 I1 I2 J K

KGUA10 53 17 50 10 3 51 26 16 16 39 Ø8 Ø14 Ø8 Ø12 12 25 25 Ø6

KGUA16 66 22 50 10 3 64 32 20 22 48 Ø10 Ø20 Ø8 Ø12 12 30 32 Ø8

KGUA20 80 32 80 10 7 78 40 30 30 60 Ø20 Ø29 Ø14 Ø22 25 38 40 Ø10

KGUA25 100 40 90 10 7 98 60 38 40 76 Ø26 Ø34 Ø14 Ø22 29 50 52 Ø10

KGUA32 100 44 90 12 9 98 60 40 40 76 Ø26 Ø40.5 Ø14 Ø22 35 50 52 Ø12

KGUA40 126 54 120 12 9 124 70 50 50 100 Ø32 Ø50.5 Ø21 Ø26 44 68 74 Ø14

Model L2 L1 M N P Q R1 R2 R3 S T U V W X Y Z

KGUA10 13 24 12 18 9 10 14 20 R9 150+Stroke Ø5.5 M3DP5 Ø9DP6.5 M3 5 17 14

KGUA16 13 24 16 22 15 14 14 20 R11 150+Stroke Ø5.5 M4DP8 Ø9DP6.5 M3 5 17 14

KGUA20 15 50 22 32 18 22 25 35 R16 106+Stroke Ø8 M4DP8 M5DP8 M4 5 15 35



KGUA40 25 70 38 55 38 40 26 43 R27.5 150+Stroke Ø10 M4DP15 M5DP16 M6 8 20 66

Dimensions

Q

4-U

2-V

4-W

KCC Co., Ltd.

www.kccpr.com181 -


Small Pin Cylinder

ACP series

ACP series

ACP - B 16 - S 30

Mounting styleB Standard

LB FootFA FlangeCB Double clevis (Except Ø6)

Bore size6 6mm

10 10mm16 16mm

Head cover positionØ6 Ø10, Ø16

Nil Axial (Standard) 90 from axialR - Axial

Not available for double rod and CB mounting type.

ActionNil Double actingS Single acting spring returnT Single acting spring extend

Not available for double rod type.

Auto switchReed A/S Model Solid State A/S Model

Nil None Nil NoneC72 D-C72K H7A1 D-H7A1KC73 D-C73K H7A2 D-H7A2KC76 D-C76K H7B D-H7BKC80 D-C80K

Refer to Auto Switch Catalogue for more information.

Cylinder strokeAction

Bore size Double acting Double rod Single rod

Ø65, 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75,

100

- 15, 30, 45, 60

Ø105, 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75, 100, 125, 150

15, 30, 45, 60 15, 30, 45, 60

Ø16

5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 75, 100, 125, 150,

175, 200

15, 30, 45, 60 15, 30, 45, 60

Number of auto switchesNil 2 pcs1 1 pcN N pcs (N: 3, 4, 5...)

Only for auto switch attached type.

SeriesACP Single rod small pin cylinder

ACPW Double rod small pin cylinder

How to Order

Symbol

Double Acting /Single Rod


Double Acting /Double Rod

Single Acting /Spring Extend

Features

Build-in magnet (Standard) Easy to install with its compact size. Piston rod with small de ection.

AccessoryNil Rod end nut (Standard) :2 pcI Single knuckle jointY Double knuckle joint

Refer to page [1]-133, for specifications about custom-made rod ends.

KCC Co., Ltd.

www.kccpr.com 191 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

ACP seriesSmall Pin Cylinder

Mounting style Standard Foot Flange Double Clevis

Standard mounting

Mounting nut -

Rod end nut

Clevis pin - - -

Option

Single knuckle joint

Double knuckle joint

For double clevis and double knuckle joint, pin and snap ring are included. Double clevis is not applicable to double rod type.

MountingBore size

Ø6 Ø10 Ø16

Foot mounting ACP B6-LB ACP B10-LB ACP B16-LB

Flange mounting ACP B6-FA ACP B10-FA ACP B16-FA

Bore size Begining of return End of return

Ø6 3.72 1.77

Ø10 6.86 3.53

Ø16 14.2 6.86

Mounting Style & Option

Mounting

Position of Port on Head Cover

Spring Return Force

For standard type, position of head cover port is on axial direction or perpendicular to axial direction. But, Ø6 type only availabe on axial direction.

Unit : g

Bore size (mm)Double Acting

Single RodDouble Acting Double Rod

Ø6 Ø10 Ø16 Ø6 Ø10 Ø16Basic mass 15 24 55 27 35 70

Additional mass for each 15mm stroke 2 4 6.5 3 6 9

Mounting mass

Foot 8 8 20 16 16 40

Flange 5 5 15 5 5 15Double clevis

(with pin) - 4 10 - - -

Accessory

Single knuckle joint - 16 24 - - -

Double knuckle joint (with pin) - 24 22 - - -

Bore sizeSpring return

(Forward)Spring extend

(Reverse)Ø6 Ø10 Ø16 Ø6 Ø10 Ø16

Basic mass

15 Stroke 11 28 63 17 28 64

30 Stroke 16 35 80 21 34 80

45 Stroke 18 44 102 23 43 100

60 Stroke 23 53 124 27 51 121

75 Stroke - - 145 - - 140

100 Stroke - - 188 - - 178

125 Stroke - - 224 - - 212

150 Stroke - - 250 - - 236

Basic mass does include the mass of mounting nut and rod end nut. Mass of double clevis does not include the mass of mounting nut.

Mass

1. Standard type Ex) ACP-LB10-S45

Basic mass: 24(Ø10) / Additional mass: 4/15 Cylinder stroke: 45mm Mass of mounting: 8(Axial foot type) 24+(4/15×45)+8=44g

2. Single acting spring return type Ex) ACP-LB10-S45T

Basic mass: 43(Ø10, 45 Stroke) / Mas of mounting: 8(Axial foot type) 43+8=51g

Calculation:

Axial direction 90 from axial

Bore sizeAccessory Ø10 Ø16

Single knuckle joint ACP B10-I ACP B16-I

Double knuckle joint ACP B10-Y ACP B16-Y

Accessory

Speci cations

Action Double acting, Single rod Double acting, Double rod Single acting, Spring return Single acting, Spring extend

Fluid Air


Max. operating pressure 7.0kgf/cm2 (700kPa)

Min. operating pressureØ6 1.2kgf/cm2 (120kPa) 1.5kgf/cm2 (150kPa) 2.0kgf/cm2 (200kPa) 2.5kgf/cm2 (250kPa)

Ø10, Ø16 0.6kgf/cm2 (60kPa) 1kgf/cm2 (100kPa) 1.5kgf/cm2 (150kPa)

Ambiet & fluid temperature 5 ~ 60

Operating piston speed 50 ~ 750mm/sec

Cushion Rubber bumper




KCC Co., Ltd.

www.kccpr.com201 -

PNEUMATIC & HYDRAULICKCC Co., Ltd.



1 Rod Cover AL

2 Head Cover AL

3 Cylinde Tube SUS

4 Piston Rod SUS

5 Piston MBSBE

6 O-Ring NBR

7 Piston Packing NBR

8 Rod Packing NBR


9 Guide Packing NBR

10 Damper Urethane

11 Magnet Nd-Fe-B

12 Mounting Nut MBSBE

13 Rod End Nut -

14 Packing Retainer AL

15 Spring Guide AL

16 Spring -

Structure

2710318

2

12413 14 119 513 4 12 8 1 9 3 10 5117 6 2

Double Acting, Single RodØ6

Double Acting, Single RodØ10, Ø16

Single Acting Spring Return

Double Acting, Double Rod

Single Acting Spring Extend

13 1 234 5 97 6101112 16 15 13 4 12 210 3 16155791 611

13 4 12 8 1 9 3 10 5117 6 1 4128 13

KCC Co., Ltd.

www.kccpr.com 211 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTSUnit : mm

Bore size A ØD H KK L ØLC LH LT LX LZ M PA PB T TL WA WB X Y

Ø6 15 3 8 M3X0.5 49 4.5 9 1.6 24 32 M6XP1.0 14.5 - 28 77 16 7 7 5

Ø10 15 4 8 M4X0.7 46 4.5 9 1.6 24 32 M8XP1.0 8 5 28 74 12.5 9.5 7 5

Ø16 15 5 8 M5X0.8 47 5.5 14 2.3 33 42 M10XP1.0 8 5 28 75 12.5 9.5 9 5

Dimensions-Double Acting/Foot (LB)

Ø6

Ø10, Ø16

Dimensions-Double Acting/Standard (B)

Unit : mm

Bore size A ØC ØD H KK L M ØNDh8 PA PB T TL VA WA WB

Ø6 15 14 3 8 M3X0.5 49 M6X1.0 6 0-0.018 14.5 - 28 77 12 16 7

Ø10 15 14 4 8 M4X0.7 46 M8X1.0 8 0-0.022 8 5 28 74 12 12.5 9.5

Ø16 15 20 5 8 M5X0.8 47 M10X1.0 10 0-0.022 8 5 28 75 18 12.5 9.5

Ø10, Ø16

Ø6


KCC Co., Ltd.

www.kccpr.com221 -

PNEUMATIC & HYDRAULIC ACP seriesSmall Pin Cylinder

Unit : mm

Bore size A ØCD CX CZ ØD H KK L M PA PB R T TL U WA WB Z

Ø10 15 3.3 3.2 12 4 8 M4XP0.7 46 M8XP1.0 8 18 5 28 87 8 12.5 22.5 82

Ø16 15 5 6.5 18 5 8 M5XP0.8 47 M10XP1.0 8 23 8 28 93 10 12.5 27.5 85

Dimensions-Double Acting/Double Clevis (CB)

Ø10, Ø16

Unit : mm

Bore size A ØD ØFC FT FX FY FZ H KK L M PA PB T TL WA WB

Ø6 15 3 Ø4.5 1.6 24 14 32 8 M3XP0.5 49 M6XP1.0 14.5 - 28 77 16 7

Ø10 15 4 Ø4.5 1.6 24 14 32 8 M4XP0.7 46 M8XP1.0 8 5 28 74 12.5 9.5

Ø16 15 5 Ø4.5 2.3 33 20 42 8 M4XP0.8 47 M10XP1.0 8 5 28 75 12.5 9.5

Dimensions-Double Acting/Rod Side Flange (FA)

Ø6

Ø10, Ø16

KCC Co., Ltd.

www.kccpr.com 231 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Small Pin Cylinder

ACP series

Dimensions-Double Acting/Double Rod (W)

Dimensions-Single Acting Spring Return (S)

Unit : mm

Bore size A ØC ØD H KK L M ØNDh8 PA T TL VA WA

Ø10 15 14 4 8 M4X0.7 49 M8X1.0 8 0-0.022 8 28 105 12 12.5

Ø16 15 20 5 8 M5X0.8 50 M10X1.0 10 0-0.022 8 28 106 18 12.5

Unit : mm

Bore size A ØC ØD H KK M ØNDh8 PA PB T VA WA WBL TL

5~15ST 16~

30ST 31~45ST 46~

60ST 5~15ST 16~

30ST 31~45ST 46~

60ST

Ø6 15 14 3 8 M3XP0.5 M6XP1.0 6 0-0.018 14.5 - 28 8 16 7 39.5 48.5 52.5 66.5 67.5 76.5 80.5 94.5

Ø10 15 14 4 8 M4XP0.7 M8XP1.0 8 0-0.022 8 5 28 12 12.5 9.5 46.5 54 66 78 74.5 82 94 106

Ø16 15 20 5 8 M5XP0.8 M10XP1.0 10 0-0.022 8 5 28 18 12.5 9.5 46 54.5 66.5 78.5 74 82.5 94.5 106.5

KCC Co., Ltd.

www.kccpr.com241 -


Small Pin Cylinder

ACP series

Unit : mm

Bore size A ØC ØD H KK M ØNDh8 PA T VA WA WB

Ø6 15 14 3 8 M3XP0.5 M6XP1.0 6 0-0.018 14.5 28 12 16 3

Ø10 15 14 4 8 M4XP0.7 M8XP1.0 8 0-0.022 8 28 12 12.5 5.5

Ø16 15 20 5 8 M5XP0.8 M10XP1.0 10 0-0.022 8 28 18 12.5 5.5

Bore sizeL TL

5~15ST 16~30ST 31~45ST 46~60ST 5~15ST 16~30ST 31~45ST 46~60ST

Ø6 51.5 60.5 64.5 78.5 79.5 88.5 92.5 106.5

Ø10 48.5 56 68 80 76.5 84 96 108

Ø16 48.5 57 69 81 76.5 85 97 109

Dimensions-Single Acting Spring Extend (T)

Ø6

Ø10, Ø16

KCC Co., Ltd.

www.kccpr.com 251 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Part no. Bore size F KK L ØNDh10 NX R1 V

ACP-B10-I Ø10 8 M4XP0.7 21 3.3 +0.048 0 3.1 8 9

ACP-B16-I Ø16 8 M5XP0.8 25 5 +0.048 0 6.4 12 14

Part no. Bore size ØDd9 Ød L m t Retaining

RingCP-10 Ø10 3.3 +0.030

+0.060 2 15.2 12.2 1 0.5 E2

CP-16 Ø16 5 +0.030+0.060 4 22.7 18.3 1.5 0.7 E4

Part no. Bore size B H M T

RN-06 Ø6 9.2 8 M6XP1.0 4

RN-10 Ø10 12.7 11 M8XP1.0 4

RN-16 Ø16 16.2 14 M10XP1.0 4

Part no. Bore size B H M T

SN-06 Ø6 6.4 5.5 M3XP0.5 2.4

SN-10 Ø10 8.1 7 M4XP0.7 3.2

SN-16 Ø16 9.2 8 M5XP0.8 4

Part no. Bore size ØDd9 Ød L m t Retaining

RingJP-10 Ø10 3.3 +0.030

+0.060 2 15.2 12.2 1 0.5 E2

JP-16 Ø16 5 +0.030+0.060 4 16.2 12.2 1.5 0.7 E4

Dimensions-Accessory

ℓ ℓ

Single Knuckle Joint

Mounting Nut

Clevis Pin Knuckle Pin

Rod End Nut

Material:Stainless steel

Material:Steel

Material:Stainless steel

Material:Brass

Material:Rolled steel

Part no. Bore size F KK L ØNDh10 NX R1 V

ACP-B10-Y Ø10 8 M4XP0.7 21 3.3 +0.048 0 3.2 8 9

ACP-B16-Y Ø16 11 M5XP0.8 25 5 +0.048 0 6.5 12 14

Double Knuckle JointMaterial:Rolled steel

Small Pin Cylinder

ACP series

KCC Co., Ltd.

www.kccpr.com261 -


Direct Mount Type Cylinder

ACD series

ACD series

Mounting styleB Bottom mountingF Front mounting

Bore size20 25 32 40

Ø20 Ø25 Ø32 Ø40

How to Order

SeriesACD Direct mount type cylinder

ACDA Direct mount type cylinder (Air cushion)

Features

Aluminium tube

WIth built-in magnet (Standard)

Square type rod cover enables direct mounting.

Space saving by mounting without bracket.

Front mounting & bottom mounting.

ACD B 32 - S 30

ACD B32-S30

MassUnit : kg

Bore size Ø20 Ø25 Ø32 Ø40

Basic mass

Bottom mounting 0.14 0.23 0.32 0.63

Front mounting 0.14 0.22 0.32 0.62

Additional mass of each 50mm stroke 0.04 0.07 0.09 0.14

Calculation:

EX.) ACD-B32-S100 Basic mass: 0.32(Ø32) / Additional mass: 0.09/50 Cylinder stroke:100mm 0.32 + 0.09/50 X 100 = 0.5kg

Symbol

Double Acting / Single Rod

Rod end attachmentNil Rod end nut(Standard):1pcI Single knuckle jointY Double knuckle joint

Refer page [1]-25 for detail information.

Cylinder strokeBore size Standard stroke Max. stroke

Ø2025, 50, 75, 100, 125, 150, 175, 200, 250,

300, 350, 400, 450, 500650

Ø25Ø32Ø40

Other intermediate strokes available on request. Refer to page [1]-133, for speci cations about custom-made rod

ends.





Only for auto switch attached type. Refer Auto Switch Catalogue for more information.

Speci cationsAction Double acting single rod

Fluid Air

Proof pressure 15kgf/cm2 (1.5MPa)

Max. operating pressure 9.9kgf/cm2 (0.99MPa)

Min. operating pressure 0.5kgf/cm2 (0.05MPa)Ambient & uid

temperature 5 ~ 60

Operating piston speed 50~750mm/sec

Cushion Rubber bumper(Standard)




Mounting style Bottom mounting, Front mounting

KCC Co., Ltd.

www.kccpr.com 271 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Direct Mount Type Cylinder

ACD series

Unit : mm

Bore size Effective thread length A B C ØC ØD ØEA KK L N PA PB

Ø20 15.5 18 5.0 22 27 10 20 +00.033 M8X1.25 76 M5X0.8 Depth 9 22 8

Ø25 19.5 22 5.5 26 33 12 26 +00.033 M10X1.25 76 M6X1.0 Depth 11 22 8

Ø32 19.5 22 5.5 30 37.5 12 26 +00.033 M10X1.25 78 M6X1.0 Depth 11 22 8

Ø40 21.0 24 7.0 36 46.5 16 32 +00.039 M14X1.25 104 M8X1.25 Depth 14 27 11

Dimensions-Front Mounting (F)

Bore size LY LZ PA PB Rc(PT) T TL VA WA WB Y Z

Ø20 30.4 33.5 22 8 1/8 27 103 24 29 15 12 39

Ø25 36.4 39 22 8 1/8 31 107 30 29 15 12 43

Ø32 42.4 47 22 8 1/8 31 109 34.5 29 15 12 43

Ø40 52.4 58.5 27 11 1/4 34 138 46.5 37.5 21 15 49

Bore size Rc(PT) T T TL VA WA WB

Ø20 1/8 27 30.4 103 24 29 15

Ø25 1/8 31 36.4 107 30 29 15

Ø32 1/8 31 42.4 109 34.5 29 15

Ø40 1/4 34 52.4 138 46.5 37.5 21

Unit : mm

Bore size Effective thread length A B ØC ØD ØEA KK L ØLC LH LX

Ø20 15.5 18 5.0 27 10 20 +00.033 M8X1.25 76 Ø5.5, Ø9.5 Depth 6.5 15 21

Ø25 19.5 22 5.5 33 12 26 +00.033 M10X1.25 76 Ø6.6, Ø11 Depth 7.5 18 25

Ø32 19.5 22 5.5 37.5 12 26 +00.033 M10X1.25 78 Ø9, Ø14 Depth 10 21 30

Ø40 21.0 24 7.0 46.5 16 32 +00.039 M14X1.25 104 Ø11, Ø17 Depth 12.5 26 38

Dimensions-Bottom Mounting (B)

KCC Co., Ltd.

www.kccpr.com281 -


Small Cylinder (Aluminium Tube)

ACS2 series

ACS2 series

ACS2 - N LB 32 - S 100

SeriesACS2 Double acting single rod small cylinder

ACS2W Double acting double rod small cylinder


Ø20 Ø25 Ø32 Ø40



Special orderNil NoneTS Multi-step stroke cylinder(Single rod)TW Multi-step stroke cylinder(Double rod)TD Tandem cylinder

ASJ Stroke adjustable type(in forward direction within 25mm)

BSJ Stroke adjustable type (in forward direction within 50mm)

S Single acting spring returnT Single acting spring extend

SV Heat resistant cylinderSS Stainless steel piston rod

LubricationN Non lubricated (Standard)L Low hydraulic pressure type ( 5kgf/cm2)G Low hydraulic pressure type ( 25kgf/cm2)

Bellows

Material Max. ambient temperature

Nil Without bellowsJ Nylon Tarpaulin 60K Neoprene Cloth 110

Rod end attachmentNil Rod end nut (Standard):1pcI Single knuckle jointY Double knuckle joint

Mounting styleB Standard TR Rod side trunnion

LB Foot TH Head side trunnionFA Rod side ange BC Boss-cut FB Head side ange BF Boss-cut ange CA Single clevis BT Boss-cut trunnion CB Double clevis

How to Order

Symbol





Features

Tube material: Aluminium

With auto switch, rubber bumper (Standard).

With non-lubricated seal.

Improved bush decreases de ection,

improves lateral load resistance.

Easy maintanance with screw fastening





Ø20 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 75, 100,

125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 550, 600

1000Ø25 1500

Ø32 2000

Ø40

25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450,

500, 600

2000

Other intermediate strokes is available upon request. Refer to page [1]-133, for Specification about custom-made rod

ends.

KCC Co., Ltd.

www.kccpr.com 291 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

TypeNon-lubricated

Low hydraulic pressureDouble acting, Single rod Double acting, Double rod Single acting spring return /

Single acting spring extendFluid Air Turbine Oil VG32


Max. operating pressure 10kgf/cm2 (1.0MPa) 5kgf/cm2 (0.5MPa)

Min. operating pressure 0.5kgf/cm2 (0.05MPa) 0.8kgf/cm2 (0.08MPa) Forward: 1.8kgf/cm2 (0.18MPa)Reverse: 2.3kgf/cm2 (0.23MPa) 1.8kgf/cm2 (0.18MPa)

Ambient & uid temperature 5 ~ 60

Operating piston speed 50 ~ 750mm/s, 15 ~ 300mm/s



Tolerance of stroke ~250ST: +1.0 0 251~500ST: +1.0

0

Speci cations

Mounting style Standard Axial foot Rod side ange

Head side ange

Integrated clevis

Single clevis

2)Double clevis

Rod side trunnion

Head side trunnion Boss cut Boss cut

angeBoss cuttrunnion

Standard

Mounting screw (1pc) (2pcs) (1pc) (1pc) - - - 1) (1pc) 1) (1pc) (1pc) (1pc) (1pc)

Rod end nut

Clevis pin - - - - - - 3) - - - - -

Option


2)Double knuckle joint

Bellows

1)Trunnion nut is included in the rod side trunnion and head side trunnion. 2)Pin and snap ring are included in double clevis and double knuckle joint. 3)Snap ring is included in clevis pin. Double rod type cylinder includes 2pcs rod end nuts.

Accessory


ACS2 series

Mounting style Minimum Order Quantity

Bore size(mm)Remarks

Ø20 Ø25 Ø32 Ø40

Axial foot 1set (2pcs) LB 20 LB 25/32 LB 40(Round type) Foot 2pcs, Nut 1pc

Flange 1pc FA/FB 20 FA/FB 25/32 FA/FB 40(Round type) Flange 1pc, Nut 1pc

Single clevis 1pc CA 20 CA 25/32 CA 40(Round type) Single clevis 1pc

Double clevis 1pc CB 20 CB 25/32 CB 40(Round type)

Double clevis 1pc,Clevis pin 1pc, Snap ring 2pcs

Trunnion 1pc TC 20 TC 25/32 TC 40 (Round type) Trunnion 1pc, Trunnion nut 1pc

Bore size(mm)Accessory Ø20 Ø25, Ø32 Ø40

Single knuckle joint I20 I25/32 I40

Double knuckle joint Y20 Y25/32 Y40

Rod end attachment of ACS2 40 and that of ACM 40 are the same.

Mounting Style

Rod End Attachment

KCC Co., Ltd.

www.kccpr.com301 -



ACS2 series

Mass

1. Double acting single rod Ex) ACS2-N-LB32-S100

Basis mass: 0.366(FootØ32) / Additional mass: 0.084/50 / Stroke: 100mm 0.366 + 0.084/50 X 100 = 0.534kg

2. Double acting double rod Ex) ACS2W-N-LB32-S100


Unit: kg

Bore size (mm)Double acting, Single rod Double acting, Double rod

Ø20 Ø25 Ø32 Ø40 Ø20 Ø25 Ø32 Ø40

Basis mass

Standard 0.154 0.238 0.288 0.626 0.176 0.283 0.329 0.727

Foot 0.228 0.316 0.366 0.778 0.250 0.361 0.407 0.879

Flange 0.198 0.290 0.340 0.734 0.220 0.335 0.381 0.835

Integrated clevis 0.134 0.208 0.248 0.566 - - - -

Single clevis 0.204 0.290 0.340 0.754 - - - -

Double clevis (With pin) 0.214 0.298 0.348 0.788 - - - -

Trunnion 0.194 0.308 0.348 0.726 0.216 0.353 0.389 0.827

Boss cut 0.144 0.218 0.268 0.596 - - - -

Boss cut ange 0.184 0.268 0.318 0.706 - - - -

Boss cut trunnion 0.184 0.288 0.328 0.696 - - - -Additional mass per each

50mm of stroke 0.064 0.080 0.084 0.140 0.096 0.120 0.137 0.205

Accessory

Single knuckle joint 0.056 0.056 0.056 0.166 - - - -

Double knuckle joint (With pin) 0.074 0.072 0.072 0.220 - - - -

Rod nut 0.002 0.008 0.008 0.016 - - - -

Calculation:

KCC Co., Ltd.

www.kccpr.com 311 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Structure

Standard (Non lubricated type) ACS2-N B

Low hydraulic pressure type ACS2-L

No. Parts Material Remark

1 Rod Carbon Steel Hard Chromium Plating

2 Rod Cover Aluminium Alloy White Anodizing

3 Head Cover Aluminium Alloy White Anodizing

4 Head Cover Aluminium Alloy Boss Cut

5 Piston Aluminium Alloy -

6 Cylinder Tube Aluminium Alloy -

7 Wearing Resin -

8 Magnet NBR -

9 Damper Urethane -

10 Bush SPCC -

No. Parts MaterialBore size

Ø20 Ø25 Ø32 Ø40

Non-lubricated

type

11 Rod Packing NBR DRP10 DRP12 DRP12 DRP16

12 Rod O-Ring NBR S6 S8 S8 S10

13Non-

Lubricated Packing

NBR OPA20 OPA25 OPA32 OPA40

Lowhydraulic pressure

type14

Low Hydraulic

Pressure type Packing



ACS2 series

Boss cut typeACS2-N BC

KCC Co., Ltd.

www.kccpr.com321 -



ACS2 series

Unit : mm

Bore size Effective thread length A B ØD ØE H KK L M PA Rc(PT) T TL

Ø20 15.5 18 5.0 10 28 13 M8X1.25 62 M20X1.5 8 1/8 41 116

Ø25 19.5 22 5.5 12 34 13 M10X1.25 62 M26X1.5 8 1/8 45 120

Ø32 19.5 22 5.5 12 38 13 M10X1.25 64 M26X1.5 8 1/8 45 122

Ø40 21.0 24 7.5 16 50 16 M14X1.50 88 M32X2.0 11 1/4 50 154

Unit : mm

Bore size Effective thread length A B ØD H KK L ØLC ØLD LH LS LT LX LZ

Ø20 15.5 18 5.0 10 13 M8X1.25 62 4 6.8 25 102 3 40 55

Ø25 19.5 22 5.5 12 13 M10X1.25 62 4 6.8 28 102 3 40 55

Ø32 19.5 22 5.5 12 13 M10X1.25 64 4 6.8 28 104 3 40 55

Ø40 21.0 24 7.5 16 16 M14X1.50 88 4 7.0 30 134 3 55 75

Bore size M PA Rc(PT) T TL VA VB W X Y

Ø20 M20X1.5 8 1/8 41 118 24 12 15 20 8

Ø25 M26X1.5 8 1/8 45 118 30 12 15 20 8

Ø32 M26X1.5 8 1/8 45 120 32 12 15 20 8

Ø40 M32X2.0 11 1/4 50 158 46 18 21 23 12

Bore size VA VB W

Ø20 24 12 15

Ø25 30 12 15

Ø32 32 12 15

Ø40 46 18 21

Dimensions-Standard (B)

Dimensions-Foot (LB)

Effective thread length


KCC Co., Ltd.

www.kccpr.com 331 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS2 series

Bore size PA Rc(PT) T TL VA VB W Y

Ø20 8 1/8 41 116 24 12 15 40

Ø25 8 1/8 45 120 30 12 15 42

Ø32 8 1/8 45 122 32 12 15 42

Ø40 11 1/4 50 154 46 18 21 52

Bore size PA Rc(PT) T TL VA VB W Y

Ø20 8 1/8 41 116 24 12 15 40

Ø25 8 1/8 45 120 30 12 15 42

Ø32 8 1/8 45 122 32 12 15 42

Ø40 11 1/4 50 154 46 18 21 52

Unit : mm

Bore size Effective thread length A B ØD ØE ØFD FT FX FY FZ H KK L M

Ø20 15.5 18 5.0 10 28 7 3.2 60 - 75 13 M8X1.25 62 M20X1.5

Ø25 19.5 22 5.5 12 34 7 4.5 60 - 75 13 M10X1.25 62 M26X1.5

Ø32 19.5 22 5.5 12 38 7 4.5 60 - 75 13 M10X1.25 64 M26X1.5

Ø40 21.0 24 7.5 16 50 7 4.5 66 36 82 16 M14X1.50 88 M32X2.0

Unit : mm

Bore size Effective thread length A B ØD ØE ØFD FT FX FY FZ H KK L M

Ø20 15.5 18 5.0 10 28 7 3.2 60 - 75 13 M8X1.25 62 M20X1.5

Ø25 19.5 22 5.5 12 34 7 4.5 60 - 75 13 M10X1.25 62 M26X1.5

Ø32 19.5 22 5.5 12 38 7 4.5 60 - 75 13 M10X1.25 64 M26X1.5

Ø40 21.0 24 7.5 16 50 7 4.5 66 36 82 16 M14X1.50 88 M32X2.0

Dimensions-Rod Side Flange (FA)

Dimensions-Head Side Flange (FB)



KCC Co., Ltd.

www.kccpr.com341 -



ACS2 series

Bore size R Rc(PT) T TL U VA VB W Z

Ø20 9 1/8 41 142 14 24 12 15 133

Ø25 9 1/8 45 146 14 30 12 15 137

Ø32 9 1/8 45 148 14 32 12 15 139

Ø40 11 1/4 50 188 18 46 18 21 177

Bore size PA R Rc(PT) T TL U VA VB W Z

Ø20 8 9 1/8 41 142 14 24 12 15 133

Ø25 8 9 1/8 45 146 14 30 12 15 137

Ø32 8 9 1/8 45 148 14 32 12 15 139

Ø40 11 11 1/4 50 188 18 46 18 21 177

Dimensions-Single Clevis (CA)

Dimensions-Double Clevis (CB)

Unit : mm

Bore size Effective thread length A B ØCD CR CX ØD ØE H KK L M PA

Ø20 15.5 18 5.0 9 30 10 10 28 13 M8X1.25 62 M20X1.5 8

Ø25 19.5 22 5.5 9 30 10 12 34 13 M10X1.25 62 M26X1.5 8

Ø32 19.5 22 5.5 9 30 10 12 38 13 M10X1.25 64 M26X1.5 8

Ø40 21.0 24 7.5 10 39 15 16 50 16 M14X1.50 88 M32X2.0 11

Unit : mm

Bore size Effective thread length A B ØCD CR CX CZ ØD ØE H KK L M

Ø20 15.5 18 5.0 9 30 10 19 10 28 13 M8X1.25 62 M20X1.5

Ø25 19.5 22 5.5 9 30 10 19 12 34 13 M10X1.25 62 M26X1.5

Ø32 19.5 22 5.5 9 30 10 19 12 38 13 M10X1.25 64 M26X1.5

Ø40 21.0 24 7.5 10 39 15 30 16 50 16 M14X1.50 88 M32X2.0



KCC Co., Ltd.

www.kccpr.com 351 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS2 series

Bore size TL TT TX ØTY TZ VA VB W Z

Ø20 116 10 32 32 52 24 12 15 36

Ø25 122 10 40 40 60 30 12 15 40

Ø32 124 10 40 40 60 32 12 15 40

Ø40 154 11 53 53 77 46 18 21 44.5

Dimensions-Rod Side Trunnion (TR)

Unit : mm

Bore size Effective thread length A B ØD ØE H KK L M PA Rc(PT) T ØTD

Ø20 15.5 18 5.0 10 28 13 M8X1.25 62 M20X1.5 8 1/8 41 8

Ø25 19.5 22 5.5 12 34 13 M10X1.25 62 M26X1.5 8 1/8 45 9

Ø32 19.5 22 5.5 12 38 13 M10X1.25 64 M26X1.5 8 1/8 45 9

Ø40 21.0 24 7.5 16 50 16 M14X1.50 88 M32X2.0 11 1/4 50 10


Bore size TL TT TX ØTY TZ VA VB W Z

Ø20 116 10 32 32 52 24 12 15 108

Ø25 122 10 40 40 60 30 12 15 112

Ø32 124 10 40 40 60 32 12 15 114

Ø40 154 11 53 53 77 46 18 21 143.5

Dimensions-Head Side Trunnion (TH)

Unit : mm

Bore size Effective thread length A B ØD ØE H KK L M PA Rc(PT) T ØTD

Ø20 15.5 18 5.0 10 28 13 M8X1.25 62 M20X1.5 8 1/8 41 8

Ø25 19.5 22 5.5 12 34 13 M10X1.25 62 M26X1.5 8 1/8 45 9

Ø32 19.5 22 5.5 12 38 13 M10X1.25 64 M26X1.5 8 1/8 45 9

Ø40 21.0 24 7.5 16 50 16 M14X1.50 88 M32X2.0 11 1/4 50 10


KCC Co., Ltd.

www.kccpr.com361 -



ACS2 series

Unit : mm

Compact (Boss Cut type)

Bore size TL

Ø20 103

Ø25 107

Ø32 109

Ø40 138

Unit : mm

Dimensions Length Comparison (Comparison with Standard type).

Ø20 Ø25 Ø32 Ø40

-13 -13 -13 -16

The total length of cylinder and space for attachment is reduced by removing the thread portion of head cover.

Dimensions-Boss Cut (BC)

Type of attachment: Standard(BC), Rod side flange type(BF), Rod Side Trunnion (BT) For not shown dimensions, refer to ACS2 Standard type.

KCC Co., Ltd.

www.kccpr.com 371 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

ACS2 seriesSmall Cylinder (Aluminium Tube)

Unit : mmPart No.

Bore size øE F L KK øND NX R V

I20 Ø20 20 16 36 M8X1.25 9 +0.060 9 -0.1

-0.2 10 14

I25/32 Ø25, 32 20 18 38 M10X1.25 9 +0.060 9 -0.1

-0.2 10 14

I40 Ø40 24 22 55 M14X1.50 12 +0.10 16 -0.1

-0.3 15.5 20

Unit : mmPart No.

Bore size øE F L KK øND NX NZ R V

Y20 Ø20 18 16 36 M8X1.25 9 +0.060 9 +0.2

+0.1 18 12 14

Y25/32 Ø25, 32 18 18 38 M10X1.25 9 +0.060 9 +0.2

+0.1 18 10 14

Y40 Ø40 24 30 55 M14X1.50 12 +0.090 16 +0.3

+0.1 38 13 25

Unit : mm

Part No. Bore size C øD H KK T

RN-02 Ø20 15.0 12.5 13 M8X1.25 5

RN-03 Ø25, 32 19.6 16.5 17 M10X1.25 6

RN-04 Ø40 25.4 21.0 22 M14X1.50 8

Unit : mm

Part No. Bore size C øD H KK T

SN-02 Ø20 34.6 29 30 M20X1.5 8

SN-03 Ø25, 32 37 31.5 32 M26X1.5 8

SN-04 Ø40 47.3 40.5 41 M32X2.0 10

Unit : mm

Part No. Bore size øD ød L N m t Remark

CJP-02 Ø20 9 -0.04-0.08 8.6 0

-0.06 19.2 25 1.75 1.15 +0.14 0 -

CJP-03 Ø25, 32 9 -0.04-0.08 8.6 0

-0.06 19.2 25 1.75 1.15 +0.14 0 -

CP-04 Ø40 10 -0.04-0.09 9.6 0

-0.09 30.2 36.2 1.85 1.15 +0.14 0 For clevis

JP-04 Ø40 12 -0.04-0.09 11.5 0

-0.11 38.2 44.2 1.85 1.15 +0.14 0 For knuckle Y


Material: Free-cutting steel

Materia: Rolled steel

Materia: Carbon steel

Materia: Rolled steel

Y20, Y25/32Material: Free-cutting steel

Y40 Materia: Cast iron


Rod End Nut

Clevis Pin

Nut

Double Knuckle Joint

KCC Co., Ltd.

www.kccpr.com381 -



ACS2 series

Dimensions-Bellows Attached Type (J, K)

Unit : mm


Ø20 15.5 18 5.0 10 28 13 M8X1.25 62 M20X1.5 8 1/8 41 144

Ø25 19.5 22 5.5 12 34 13 M10X1.25 62 M26X1.5 8 1/8 45 152

Ø32 19.5 22 5.5 12 38 13 M10X1.25 64 M26X1.5 8 1/8 45 154

Ø40 21.0 24 7.5 16 50 16 M14X1.50 88 M32X2.0 11 1/4 50 188

Bore size VA VB W

Ø20 24 12 15

Ø25 30 12 15

Ø32 32 12 15

Ø40 46 18 21

Dimensions-Double Rod (W)



Unit : mm

Bore size F ØG s t TL

Ø20 16 39 0.3 stroke+3 56 131

Ø25 16 39 0.3 stroke+3 60 135

Ø32 16 39 0.3 stroke+3 60 137

Ø40 18 40 0.25 stroke+3 67 171

Type J K

Material Nylon Tarpaulin Neoprene cloth

Heat Resistant 60 110

For dimensions not shown in these figues, refer to the ACS2 standard type. SUS band is mounted at bellows at delivery.

KCC Co., Ltd.

www.kccpr.com 391 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS2 series

Single Rod Multi-Step Stroke Cylinder (TS)

Dimensions-Single Rod Multi-Step Stroke type (TS)

Unit : mm

Bore size TA TB TL

Ø20 48 62 164

Ø25 48 62 168

Ø32 50 64 172

Ø40 67 88 221

For dimensions not shown in these figues, refer to the ACS2 (Standard) type.

Double Rod Multi-Step Stroke Cylinder (TW)

Head side assembly. By integrating two cylinders enable back and forth stroke and three steps control.Ordering notation: A Stroke + B StrokeExample) 150 + 50 (A Side = 150, B Side = 50)

Dimensions-Double Rod Multi-Step Stroke type (TW)

Unit : mm

Bore size TL X

Ø20 232 26

Ø25 240 26

Ø32 244 26

Ø40 310 34

When A and B ports are supplied with air pressure, A and B strokes reverse.

When C and D ports are supplied with air pressure, A and B strokes move forward.

When A and C ports are supplied with air pressure, B stroke move forward.

When B and D ports are supplied with air pressure, A stroke move forward.

By integrating two cylinders in series enable back and forth stroke and two-steps control for a doubled output.Ordering notation: A Stroke + Total StrokeEx) 150 + 200 (A Side = 150, B Side = 50)

When B port is supplied with air pressure, A and B strokes reverse.

When both A and C ports are suppl ied with a ir pressure, forward output is doubled.

When C port is supplied with air pressure, rod and B Stroke move forward.

When A port is supplied with air pressure, rod and A Stroke move forward.

KCC Co., Ltd.

www.kccpr.com401 -



ACS2 series

Tandem Cylinder (TD)

Dimensions-Tandem Cylinder (TD)

ADJUSTMENTADJUSTMENT



Dimensions-Stroke Adjustable (ASJ, BSJ)

To adjust the entire forward stroke from 0mm to 50mm an adjustment mechanism is attached to the head side.

Range of adjustment

Unit : mm

Bore size KK MA MK ØMI MH ML TL

Ø20 M8X1.25 12 8 20 47 20 150

Ø25 M10X1.25 17 10 25 49 22 156

Ø32 M10X1.25 17 10 25 49 22 158

Ø40 M14X1.50 22 12 30 60 26 198

Stroke Adjustable Cylinder (ASJ, BSJ)

ASJ : 25mm adjustmentBSJ : 50mm adjustmentXSJ : Xmm adjustment (X is de ned by user)

Unit : mm

Bore size TA TB TL

Ø20 48 62 164

Ø25 48 62 168

Ø32 50 64 172

Ø40 67 88 221 For dimensions not shown in these figues, refer to the ACS2 standard type.

Two cylinders connected in series for a doubled output.

When A and B ports are supplied with air pressure, reverse operating output is doubled.

When A and C ports are supplied with air pressure, forward operating output is doubled.

KCC Co., Ltd.

www.kccpr.com 411 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS2 series

Dimensions-Single Acting Spring Return (S), Spring Extend (T)



Unit : mm

Bore size Effective thread length A B ØD E H KK PA Rc(PT) T VA VB W

Ø20 15.5 18 5 10 28 13 M8×1.25 8 1/8 41 24 12 15Ø25 19.5 22 5.5 12 34 13 M10×1.25 8 1/8 45 30 12 15Ø32 19.5 22 5.5 12 38 13 M10×1.25 8 1/8 45 34.5 12 15Ø40 21 24 7 16 50 13 M14×1.5 11 1/4 50 42.5 18 21.5

StrokeBore size

1~50 51~100 101~150 151~200 201~250L TL L TL L TL L TL L TL

Ø20 87 141 112 166 137 191 - - - -Ø25 87 145 112 170 137 195 - - - -Ø32 89 147 114 172 139 197 164 222 - -Ø40 113 179 138 204 163 229 188 254 213 279

Type Lubricated type

Bore size Ø20, Ø25, Ø32, Ø40

Ambient temperature -20~150

Packing Material VITON

Type Lubricated type, Non-lubricated type


Rod Material SUS 303

Heat Resistant Cylinder (SV)Heat resistant cylinder can be used at a high ambient temperature up to150 by equipped with heat-resistant seal.

Stainless steel cylinder rod is selected to prevent the end of rod from corrosion when it is in contact with water during operation.

Speci cations

Stainless Steel Piston Rod (SS)

Speci cations



KCC Co., Ltd.

www.kccpr.com 421 -


ACS3 series

Small Cylinder (Stainless Steel Tube)

ACS3 series

ACS3-N B32-S150


Ø2025, 50, 75, 100, 125, 150, 175, 200, 250,

300, 350, 400, 450, 500650

Ø25Ø32Ø40


ends.

ACS3 - N B 32 - S 150

SeriesACS3 Double acting single rod small cylinder

ACS3W Double acting double rod small cylinder


Ø20 Ø25 Ø32 Ø40



Special orderNil NoneTW Multi-step stroke cylinder (Double rod)





LubricationN Non-lubricated (Standard)L Low hydraulic pressure type ( 5kgf/cm2)

Bellows




Mounting styleB Standard CD Integrated Clevis

LB Foot TR Rod Side TrunnionFA Rod Side Flange TH Head Side TrunnionFB Head Side Flange BC Boss-cutCA Single Clevis BF Boss-cut Flange CB Double Clevis BT Boss-cut Trunnion

How to Order



Only for auto switch attached type. Refer to Auto Switch Catalogue for more information.

Symbol





Features

Tube material: Stainless steel

With auto switch, rubber bumper (Standard).




Lighter and more compact in size than

that of conventional type.

KCC Co., Ltd.

www.kccpr.com 431 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS3 series

TypeNon-Lubricated

Low hydraulic pressureDouble acting, Single rod Double acting, Double rod Single acting spring return /

Single acting spring extendFluid Air Turbine Oil VG32


Max. operating pressure 10kgf/cm2 (1.0MPa) 5kgf/cm2 (0.5MPa)

Min. operating pressure 0.5kgf/cm2 (0.05MPa) 0.8kgf/cm2 (0.08MPa) Forward: 1.8kgf/cm2 (0.18MPa)Reverse: 2.3kgf/cm2 (0.23MPa) 1.8kgf/cm2 (0.18MPa)


Operating piston speed 50 ~ 750mm/s 15 ~ 300mm/s



Tolerance of stroke ~250ST: +1.0 0 251~500ST: +1.0

0

Speci cations

Accessory

Mounting style Minimum order quantity


Ø20 Ø25 Ø32 Ø40






Trunnion 1pc TC 20 TC 25/32 TC 40(Round type) Trunnion 1pc, Trunnion nut 1pc


Single Knuckle Joint I20 I25/32 I40

Double Knuckle Joint Y20 Y25/32 Y40

Rod end attachment of ACS3 40 and that of ACM 40 are the same. Rod end attachment is the same as ACS2 series. Refer page [1]-37 for more information.

Mounting Style

Rod End Attachment

Mounting style Standard Axial foot

Rod side ange

Head side ange

Integrated clevis

Single clevis

2)Double clevis

Rod side trunnion

Head side trunnion Boss-cut Boss-cut

FlangeBoss-cutTrunnion

Standard


Rod end nut

Clevis Pin - - - - - - 3) - - - - -

Option


2)Double Knuckle Joint

Bellows

1)Trunnion nut is included in the rod side trunnion and head side trunnion. 2)Pin and snap ring are included in double clevis and double knuckle joint. 3)Snap ring is included in clevis pin. For double rod type cylinder, rod end nuts (2pcs) are included.

KCC Co., Ltd.

www.kccpr.com 441 -



ACS3 series

Mass

1. Double acting single rod Ex) ACS3-N-LB32-S100


2. Double acting double rod Ex) ACS3W-N-LB32-S100


Unit: kg

Bore size (mm)Double acting, Single rod Double acting, Double rod

Ø20 Ø25 Ø32 Ø40 Ø20 Ø25 Ø32 Ø40

Basis mass

Standard 0.150 0.228 0.280 0.568 0.171 0.271 0.320 0.659

Foot 0.224 0.306 0.358 0.720 0.245 0.349 0.398 0.811

Flange 0.194 0.280 0.332 0.676 0.215 0.323 0.372 0.767

Integrated clevis 0.130 0.208 0.270 0.528 - - - -

Single clevis 0.200 0.280 0.332 0.696 - - - -

Double clevis (With pin) 0.210 0.288 0.340 0.730 - - - -

Trunnion 0.190 0.298 0.340 0.668 0.211 0.341 0.380 0.759

Boss cut 0.140 0.208 0.260 0.538 - - - -

Boss cut ange 0.180 0.258 0.310 0.648 - - - -

Boss cut trunnion 0.180 0.278 0.320 0.638 - - - -Additional mass per each

50mm of stroke 0.048 0.068 0.076 0.132 0.720 0.102 0.124 0.193

Accessory


Double knuckle joint (With pin) 0.074 0.072 0.072 0.220 - - - -

Rod nut 0.002 0.008 0.008 0.016 - - - -

Calculation:

KCC Co., Ltd.

www.kccpr.com 451 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS3 series



2 Rod Cover AL Alloy White Anodizing

3 Head Cover AL Alloy White Anodizing

4 Head Cover AL Alloy Boss Cut

5 Piston AL Alloy -

6 Cylinder Tube SUS304 -

7 Wearing Resin -

8 Magnet NBR -

9 Spring Wash Hard Steel Wire -

10 Damper Urethane -

11 Bush Copper -

Part no. Parts MaterialBore size

Ø20 Ø25 Ø32 Ø40

Non lubricated

12 Rod Packing NBR DRP10 DRP12 DRP12 DRP16


14Non

Lubricated Packing


Low hydraulic pressure

15

Low Hydraulic

Pressure type Packing

NBR HSD20 HSD25 HSD32 HSD40

Structure

Standard (Non lubricated) ACS3-N B

Boss cut ACS3-N BC

Low hydraulic pressure type ACS3-L

KCC Co., Ltd.

www.kccpr.com 461 -


Unit : mm

Bore size Effective thread length A B ØC ØD H KK L M PA Rc(PT) T TL

Ø20 15.5 18 5.0 27 10 13 M8X1.25 62 M20X1.5 8 1/8 41 116

Ø25 19.5 22 5.5 33 12 13 M10X1.25 62 M26X1.5 8 1/8 45 120

Ø32 19.5 22 5.5 37.5 12 13 M10X1.25 64 M26X1.5 8 1/8 45 122

Ø40 21.0 24 7.5 46.5 16 16 M14X1.50 88 M32X2.0 11 1/4 50 154

Bore size VA W

Ø20 24 15

Ø25 30 15

Ø32 34.5 15

Ø40 42.5 21




ACS3 series

Bore size LZ M PA Rc(PT) T TL W X Y

Ø20 55 M20X1.5 8 1/8 41 131 15 20 8

Ø25 55 M26X1.5 8 1/8 45 135 15 20 8

Ø32 55 M26X1.5 8 1/8 45 137 15 20 8

Ø40 75 M32X2.0 11 1/4 50 173 21 23 12


Unit : mm

Bore size Effective thread length A B ØD H KK L ØLC ØLD LH LS LT LX

Ø20 15.5 18 5.0 10 13 M8X1.25 62 4 6.8 25 102 3.2 40

Ø25 19.5 22 5.5 12 13 M10X1.25 62 4 6.8 28 102 3.2 40

Ø32 19.5 22 5.5 12 13 M10X1.25 64 4 6.8 28 104 3.2 40

Ø40 21.0 24 7.5 16 16 M14X1.50 88 4 7.0 30 134 3.2 55


KCC Co., Ltd.

www.kccpr.com 471 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS3 series

Bore size PA Rc(PT) T TL W Y

Ø20 8 1/8 41 116 15 40

Ø25 8 1/8 45 120 15 42

Ø32 8 1/8 45 122 15 42

Ø40 11 1/4 50 154 21 52


Unit : mm

Bore size Effective thread length A B ØD ØFD FT FX FY FZ H KK L M

Ø20 15.5 18 5.0 10 7 3.2 60 - 75 13 M8X1.25 62 M20X1.5

Ø25 19.5 22 5.5 12 7 4.5 60 - 75 13 M10X1.25 62 M26X1.5

Ø32 19.5 22 5.5 12 7 4.5 60 - 75 13 M10X1.25 64 M26X1.5

Ø40 21.0 24 7.5 16 7 4.5 66 36 82 16 M14X1.50 88 M32X2.0


Bore size PA Rc(PT) T TL W Y

Ø20 8 1/8 41 116 15 40

Ø25 8 1/8 45 120 15 42

Ø32 8 1/8 45 122 15 42

Ø40 11 1/4 50 154 21 52


Unit : mm

Bore size Effective thread length A B ØD ØFD FT FX FY FZ H KK L M

Ø20 15.5 18 5.0 10 7 3.2 60 - 75 13 M8X1.25 62 M20X1.5

Ø25 19.5 22 5.5 12 7 4.5 60 - 75 13 M10X1.25 62 M26X1.5

Ø32 19.5 22 5.5 12 7 4.5 60 - 75 13 M10X1.25 64 M26X1.5

Ø40 21.0 24 7.5 16 7 4.5 66 36 82 16 M14X1.50 88 M32X2.0


KCC Co., Ltd.

www.kccpr.com 481 -


Bore size R Rc(PT) T TL U VA W Z

Ø20 9 1/8 41 142 14 24 15 133

Ø25 9 1/8 45 146 14 30 15 137

Ø32 9 1/8 45 148 14 34.5 15 139

Ø40 11 1/4 50 188 18 42.5 21 177


Unit : mm

Bore size Effective thread length A B ØC ØCD CR CX ØD H KK L M PA

Ø20 15.5 18 5.0 27 9 30 10 10 13 M8X1.25 62 M20X1.5 8

Ø25 19.5 22 5.5 33 9 30 10 12 13 M10X1.25 62 M26X1.5 8

Ø32 19.5 22 5.5 37.5 9 30 10 12 13 M10X1.25 64 M26X1.5 8

Ø40 21.0 24 7.5 46.5 10 39 15 16 16 M14X1.50 88 M32X2.0 11



ACS3 series

Bore size PA R Rc(PT) T TL U VA W Z

Ø20 8 9 1/8 41 142 14 24 15 133

Ø25 8 9 1/8 45 146 14 30 15 137

Ø32 8 9 1/8 45 148 14 34.5 15 139

Ø40 11 11 1/4 50 188 18 42.5 21 177


Unit : mm

Bore size Effective thread length A B ØC ØCD CR CX CZ ØD H KK L M

Ø20 15.5 18 5.0 27 9 30 10 19 10 13 M8X1.25 62 M20X1.5

Ø25 19.5 22 5.5 33 9 30 10 19 12 13 M10X1.25 62 M26X1.5

Ø32 19.5 22 5.5 37.5 9 30 10 19 12 13 M10X1.25 64 M26X1.5

Ø40 21.0 24 7.5 46.5 10 39 15 30 16 16 M14X1.50 88 M32X2.0


KCC Co., Ltd.

www.kccpr.com 491 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS3 series

Unit : mm

Bore size Effective thread length A B ØD H KK L M PA Rc(PT) T ØTD TL

Ø20 15.5 18 5.0 10 13 M8X1.25 62 M20X1.5 8 1/8 41 8 116

Ø25 19.5 22 5.5 12 13 M10X1.25 62 M26X1.5 8 1/8 45 9 120

Ø32 19.5 22 5.5 12 13 M10X1.25 64 M26X1.5 8 1/8 45 9 122

Ø40 21.0 24 7.5 16 16 M14X1.50 88 M32X2.0 11 1/4 50 10 154

Bore size TT TX ØTY TZ W Z

Ø20 10 32 32 52 15 36

Ø25 10 40 40 60 15 40

Ø32 10 40 40 60 15 40

Ø40 11 53 53 77 21 44.5

Dimensions-Rod Side Trunnion (TR)


Bore size Rc(PT) T TL U VA W Z

Ø20 1/8 41 124 12 24 15 115

Ø25 1/8 45 128 12 30 15 119

Ø32 1/8 45 136 15 34.5 15 124

Ø40 1/4 50 165 15 42.5 21 153

Dimensions-Integrated Clevis (CD)

Unit : mm

Bore size Effective thread length A B ØC ØCD CX ØD H KK L M PA R

Ø20 15.5 18 5.0 27 8 12 10 13 M8X1.25 62 M20X1.5 8 9

Ø25 19.5 22 5.5 33 8 12 12 13 M10X1.25 62 M26X1.5 8 9

Ø32 19.5 22 5.5 37.5 10 20 12 13 M10X1.25 64 M26X1.5 8 12

Ø40 21.0 24 7.5 46.5 10 20 16 16 M14X1.50 88 M32X2.0 11 12


KCC Co., Ltd.

www.kccpr.com 501 -



ACS3 series

Compact Boss cut

Bore size (mm) TL

Ø20 103

Ø25 107

Ø32 109

Ø40 138

Dimensions Length Comparison (Comparison with Standard type).

Ø20 Ø25 Ø32 Ø40

-13 -13 -13 -16

The total length of cylinder and space for attachment is reduced by removing the thread portion of head cover.

Dimensions-Boss cut (BC)

Unit : mm

Bore size Effective thread length A B ØD H KK L M PA Rc(PT) T ØTD TL

Ø20 15.5 18 5.0 10 13 M8X1.25 62 M20X1.5 8 1/8 41 8 118

Ø25 19.5 22 5.5 12 13 M10X1.25 62 M26X1.5 8 1/8 45 9 122

Ø32 19.5 22 5.5 12 13 M10X1.25 64 M26X1.5 8 1/8 45 9 124

Ø40 21.0 24 7.5 16 16 M14X1.50 88 M32X2.0 11 1/4 50 10 154

Bore size TT TX ØTY TZ W Z

Ø20 10 32 32 52 15 108

Ø25 10 40 40 60 15 112

Ø32 10 40 40 60 15 114

Ø40 11 53 53 77 21 143.5

Dimensions-Head Side Trunnion (TH)


Type of attachment: Standard(BC), Rod side flange type(BF), Rod Side Trunnion(BT) For not shown dimensions, refer to ACS3 standard type.

KCC Co., Ltd.

www.kccpr.com 511 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS3 series

Unit : mm

Bore size Effective thread length A B ØD H KK L M PA Rc(PT) T TL W

Ø20 15.5 18 5.0 10 13 M8X1.25 62 M20X1.5 8 1/8 41 144 15

Ø25 19.5 22 5.5 12 13 M10X1.25 62 M26X1.5 8 1/8 45 152 15

Ø32 19.5 22 5.5 12 13 M10X1.25 64 M26X1.5 8 1/8 45 154 15

Ø40 21.0 24 7.5 16 16 M14X1.50 88 M32X2.0 11 1/4 50 188 21

Dimensions-Double Rod (W)




Unit : mm

Bore size F ØG s t TL

Ø20 16 39 0.3 Stroke + 3 56 131

Ø25 16 39 0.3 Stroke + 3 60 135

Ø32 16 39 0.3 Stroke + 3 60 137

Ø40 18 40 0.25 Stroke + 3 67 171

For dimensions not shown in these figues, refer to the ACS3 standard type. SUS band is mounted at bellows at delivery.


Type J K

Material Nylon Tarpaulin Neoprene Cloth

Temperature 60 110

KCC Co., Ltd.

www.kccpr.com 521 -



ACS3 series


Forward Stroke Adjustable Cylinder (ASJ, BSJ)

Dimensions-Double Rod Multi-Step Stroke Cylinder (TW)

Dimensions-Forward Stroke Adjustable Cylinder (ASJ, BSJ)

Unit : mm

Bore size KK MA MH ØMI MK ML TL

Ø20 M8X1.25 12 47 20 8 20 150

Ø25 M10X1.25 17 49 25 10 22 156

Ø32 M10X1.25 17 49 25 10 22 158

Ø40 M14X1.50 22 60 30 12 26 198





ASJ : 25mm adjustmentBSJ : 50mm adjustmentXSJ : Xmm adjustment (X: stroke decided by user)

Unit : mm

Bore size TL X

Ø20 232 26

Ø25 240 26

Ø32 244 26

Ø40 310 34

Range of adjustment






KCC Co., Ltd.

www.kccpr.com 531 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS



ACS3 seriesSmall Cylinder (Stainless Steel Tube)

Heat Resistant Cylinder (SV)

Heat resistant cylinder can be used at a high ambient temperature up to 150 by equipped with heat-resistant seal.


Stainless Steel Piston Rod (SS)

Dimensions-Single Acting Spring Return (S), Spring Extend (T)

Unit : mm

Bore size Effective thread length A B C ØD H KK PA Rc(PT) T VA VB W

Ø20 15.5 18 5 28 10 13 M8×1.25 8 1/8 41 24 15 15Ø25 19.5 22 5.5 33.5 12 13 M10×1.25 8 1/8 45 30 15 15Ø32 19.5 22 5.5 37.5 12 13 M10×1.25 8 1/8 45 34.5 15 15Ø40 21 24 7 46.5 16 13 M14×1.5 11 1/4 50 42.5 21.5 21.5

Unit : mm

StrokeBore size

1~50 51~100 101~150 151~200 201~250L TL L TL L TL L TL L TL

Ø20 87 141 112 166 137 191 - - - -Ø25 87 145 112 170 137 195 - - - -Ø32 89 147 114 172 139 197 164 222 - -Ø40 113 179 138 204 163 229 188 254 213 279







Type Lubricated type, Non-lubricated type


Rod Material SUS 303

Speci cations Speci cations

KCC Co., Ltd.

www.kccpr.com541 -


Small Cylinder (Aluminium Tube/Air Cushion)

ACS4 series

ACS4 series

Symbol


Double Acting / Double Rod

Features

Aluminum tube With built-in magnet (Standard). With non-lubricated seal. Improved bush decreases de ection and

improves lateral load resistance. Easy maintenance with screw fastening. Rod seal is easy to be replaced

ACS4A - N LB 32 - S 100

Series

ACS4A Double acting single rod small cylinder(With air cushion)

ACS4AW Double acting double rod small cylinder(With air cushion)


Ø20 Ø25 Ø32 Ø40



Special orderNil NoneTS Multi-step stroke cylinder(Single rod)TW Multi-step stroke cylinder(Double rod)TD Tandem cylinder




LubricationN Non lubricated (Standard)

Bellows


Nil Without bellowsJ Nylon Tarpaulin 60K Neoprene cloth 110


Mounting styleB Standard CD Integrated clevisLB Foot TR Rod side trunnionFA Rod side ange TH Head side trunnionFB Head side ange BC Boss-cutCA Single clevis BF Boss-cut ange CB Double clevis BT Boss-cut trunnion

How to Order


Ø20 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 75, 100,

125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 550, 600

1000Ø25 1500

Ø32 2000

Ø40

25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450,

500, 600

2000


ends.




KCC Co., Ltd.

www.kccpr.com 551 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS4 series

Speci cations

TypeNon-Lubricated

Double acting, Single rod Double acting, Double rod

Fluid Air



Min. operating pressure 0.5kgf/cm2 (0.05MPa) 0.8kgf/cm2 (0.08MPa)


Operating piston speed 50 ~ 1000mm/s

Cushion Air cushion


Tolerance of stroke ~250ST: +1.0 0



Ø20 Ø25 Ø32 Ø40








Single Knuckle Joint I20 I25/32 I40

Double Knuckle Joint Y20 Y25/32 Y40


Mounting Style

Rod End Attachment

Accessory


Head side ange

Integrated clevis

Single clevis

2)Double clevis

Rod side trunnion

Head side trunnion Boss cut Boss cut

angeBoss cuttrunnion

Standard


Rod end nut

Clevis pin - - - - - - 3) - - - - -

Option



Bellows


KCC Co., Ltd.

www.kccpr.com561 -


Structure

Standard (Non lubricated) ACS4A-N B


ACS4 series

Boss-cut ACS4A-N BC





4 Head Cover AL Alloy Boss Cut Type

5 Cylinder Tube AL Alloy -

6 Piston AL Alloy -

7 Magnet Holder AL Alloy -

8 Cushion Ring AL Alloy -

9 Cushion Ring Nut AL Alloy -

10 Stop Ring Carbon Tool Steel -

11 Packing Wash Rolled Steel -

12 Bush Sintered Metal -

13 Magnet - -

14 Wearing Resin -


Ø20 Ø25 Ø32 Ø4015 Rod Packing NBR DRP8 DRP10 DRP12 DRP14

16 Cushion Packing NBR - - - -

17 Piston Packing NBR OPA20 OPA25 OPA32 OPA40


KCC Co., Ltd.

www.kccpr.com 571 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS4 series

Unit : mm


Ø20 15.5 18 5.0 8 28 13 M8X1.25 62 M20X1.5 8 1/8 41 116

Ø25 19.5 22 5.5 10 34 13 M10X1.25 62 M26X1.5 8 1/8 45 120

Ø32 19.5 22 5.5 12 38 13 M10X1.25 64 M26X1.5 8 1/8 45 122

Ø40 21.0 24 7.5 14 50 16 M14X1.50 88 M32X2.0 11 1/4 50 154

Bore size VA VB W Y

Ø20 24 12 15 8.5

Ø25 30 12 15 10

Ø32 32 12 15 12

Ø40 46 18 21 15.5



Except dimensions ØD and Y, all of the dimensions above are the same as ACS2 series. (Refer to ACS2 series.)

KCC Co., Ltd.

www.kccpr.com 581 -


ACS5 series

Small Cylinder (Stainless Steel Tube/Air Cushion)

ACS5 series

Symbol



Features

Tube material: Stainless steel

With built-in magnet (Standard).




ACS5A-N B32-S150


Ø2025, 50, 75, 100, 125, 150, 175, 200, 250,

300, 350, 400, 450, 500650

Ø25Ø32Ø40


ends.

ACS5A - N B 32 - S 150

Series

ACS5A Double acting single rod small cylinder (With air cushion)

ACS5AW Double acting double rod small cylinder(With air cushion)


Ø20 Ø25 Ø32 Ø40



Special orderNil NoneTW Multi-step stroke cylinder(Double rod)




LubricationN Non lubricated (Standard)

Bellows




Mounting styleB Standard CD Integrated clevisLB Foot TR Rod side trunnionFA Rod side ange TH Head side trunnionFB Head side ange BC Boss-cutCA Single clevis BF Boss-cut ange CB Double clevis BT Boss-cut trunnion

How to Order



Only for auto switch attached type. Refer to Auto Switch Catalogue for more information.

KCC Co., Ltd.

www.kccpr.com 591 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACS5 series

Speci cations

TypeNon-Lubricated

Double acting, Single rod Double acting, Double rodFluid Air



Min. operating pressure 0.5kgf/cm2 (0.05MPa) 0.8kgf/cm2 (0.08MPa)Ambient & uid

temperature 5 ~ 60


Cushion Air cushion


Tolerance of stroke ~250ST: +1.0 0



Ø20 Ø25 Ø32 Ø40

Axial foot 1set (2pcs) LB 20 LB 25/32 LB 40(Round type) Foot 2pcs, Mounting nut 1pc

Flange 1pc FA/FB 20 FA/FB 25/32 FA/FB 40(Round type) Flange 1pc, Mounting nut 1pc






Single knuckle joint I20 I25/32 I40

Double knuckle joint Y20 Y25/32 Y40


Mounting Style

Rod End Attachment

Accessory


Head side ange

Integrated clevis

Single clevis

2)Double clevis

Rod side trunnion

Head side trunnion Boss-cut Boss cut

FlangeBoss cutTrunnion

Standard


Rod end nut

Clevis pin - - - - - - 3) - - - - -

Option



Bellows


KCC Co., Ltd.

www.kccpr.com 601 -



ACS5 series

Structure

Standard (Non lubricated) ACS5-N B

Boss-cut ACS5-N BC






5 Cylinder Tube Stainless Steel -

6 Piston AL Alloy -

7 Magnet Holder AL Alloy -

8 Cushion Ring AL Alloy -

9 Cushion Ring Nut AL Alloy -

10 Stop Ring Carbon Tool Steel -

11 Packing Wash Rolled Steel -

12 Bush Sintered Metal -

13 Magnet - -

14 Wearing Resin -


Ø20 Ø25 Ø32 Ø4015 Rod Packing NBR DRP8 DRP10 DRP12 DRP14

16 Cushion Packing NBR - - - -

17 Piston packing NBR OPA20 OPA25 OPA32 OPA40


KCC Co., Ltd.

www.kccpr.com 611 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Unit : mm

Bore size Effective thread length A B ØC ØD H KK L M PA Rc(PT) T TL

Ø20 15.5 18 5.0 27 8 13 M8X1.25 62 M20X1.5 8 1/8 41 116

Ø25 19.5 22 5.5 33 10 13 M10X1.25 62 M26X1.5 8 1/8 45 120

Ø32 19.5 22 5.5 37.5 12 13 M10X1.25 64 M26X1.5 8 1/8 45 122

Ø40 21.0 24 7.5 46.5 14 16 M14X1.50 88 M32X2.0 11 1/4 50 154

Bore size VA W Y

Ø20 24 15 8

Ø25 30 15 10

Ø32 34.5 15 12

Ø40 42.5 21 15.5




ACS5 series

Except dimensions ØD and Y, all of the dimensions above are the same as ACS3 series. (Refer to ACS3 series.)

KCC Co., Ltd.

www.kccpr.com 621 -


Round Cylinder

ACR series

ACR series

ACR - N B 63 - S 100

SeriesACR Round cylinder (Aluminium tube)

Bore size50 63 80 100

Ø50 Ø63 Ø80 Ø100

Cylinder stroke25, 50, 75, 100, 125, 150, 200, 250, 300, 400, 500

LubricationN Non-lubricated type (Standard)

Rod end attachmentNil Rod end nut (Standard) : 1pcI Single knuckle jointY Double knuckle joint

Mounting styleB StandardFA Rod side angeFB Head side angeCB Double clevis

How to Order

ACR-N B63-S100

Symbol


Features

Aluminium tube

Shorthened round cylinder

Lighter weight than that of conventional

type

Flange type and double clevis mounting is

available


Type Non lubricated

Cylinder Bore size Ø50, Ø63, Ø80, Ø100

Fluid Air



Min. operating pressure 0.5kgf/cm2 (0.05MPa)

Ambient & fluid temperature 5 ~ 60




Tolerance of stroke ~ 1000ST: +1.4 0 , 1001 ~ 1500ST: +1.8

0

Speci cations

KCC Co., Ltd.

www.kccpr.com 631 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Round Cylinder

ACR series

Unit : mm

Bore size Standard stroke range

Long stroke range A AL C D E F PA PB T H I J B KA KK

Ø50 ~300 301~1200 35 32 32 20 30 2 14 12 58 11 56 M8XP1.25Depth16 7 18 M18XP1.5

Ø63 ~300 301~1200 35 32 38 20 32 2 14 12 58 11 69 M10XP1.5Depth16 7 18 M18XP1.5

Ø80 ~300 301~1400 40 37 50 25 40 3 20 16 71 13 87 M10XP1.5Depth22 10 22 M22XP1.5

Ø100 ~300 301~1500 40 37 60 30 50 3 20 16 71 16 108 M12XP1.75Depth22 10 26 M26XP1.5

Unit : mm

Bore size Stroke range B E F FX FD FT T

Ø50 ~750 76 30 2 58 9 9 58

Ø63 ~750 92 32 2 70 11 9 58

Ø80 ~750 104 40 3 82 11 11 71

Ø100 ~750 128 50 3 100 14 14 71



Bore size NA Rc(PT) L TA TB TL TC TDH9 TE TG

Ø50 55 1/4 102 13 12 162 M12XP1.25 16 +0.080 7.5 10

Ø63 69 1/4 102 13 12 162 M14XP1.5 18 +0.080 11.5 14.5

Ø80 80 3/8 122 - - 196 - - - -

Ø100 100 1/2 122 - - 196 - - - -

For Ø80, Ø100 cylinder bore size, NA(width cross flat) does not have trunnion mounting tap. Contact us for built-in magnet type.

ØE is on flange mounting. For dimensions not shown in these figues, refer to the standard type.

KCC Co., Ltd.

www.kccpr.com 641 -


Round Cylinder

ACR series

Unit : mm

Bore size Stroke range CD CX CZ CL RR V TT TZ TL

Ø50 ~600 16 - 60 25 20 - 6 86 185

Ø63 ~600 18 - 74 30 22 - 8 105.4 190

Ø80 ~750 18 28 56 35 18 26 - 64 228

Ø100 ~750 22 32 64 43 22 32 - 72 236


For dimensions not shown in these figues, refer to the standard type.

Unit : mm

Bore size Stroke range B E F FX FD FT T TL

Ø50 ~750 76 30 2 58 9 9 58 162

Ø63 ~750 92 32 2 70 11 9 58 162

Ø80 ~750 104 40 3 82 11 11 71 196

Ø100 ~750 128 50 3 100 14 14 71 196


ØE is on flange mounting. For dimensions not shown in these figues, refer to the

standard type.

Ø50, Ø63

Ø80, Ø100

KCC Co., Ltd.

www.kccpr.com 651 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Pressurized on rod side

Pressurized on head side

Medium Cylinder

ACM series

ACM series

Series

ACM Double acting single rod medium cylinder

ACMW Double acting double rod medium clylinder

Tube size40 50 63 80 100

Ø40 Ø50 Ø63 Ø80 Ø100



Special orderNil NoneTS Multi-step stroke cylinder(Single rod)TW Multi-step stroke cylinder (Double rod)TD Tandem cylinder

ASJ Stroke adjustable type (in forward direction within 25mm)




Low friction direction

R Side at pressure when pressurized on head side

H Side at pressure when pressurized on rod size

Only for low friction type.

LubricationN Not required(Standard)

L Low hydraulic pressure ( 5kgf/cm2)

G Low hydraulic pressure( 25kgf/cm2)

Q Low friction type

Rod end attachmentNil Rod end nut 1pc (Standard)I Single knuckle jointY Double knuckle joint

Mounting bracketNil None

KA2 TrunnionCB2 Clevis

Mounting styleB Standard CB Double clevis

LB Foot TC Center trunnionFA Rod side ange TA Rod side trunnionFB Head side ange TB Head side trunnionCA Single clevis

How to Order

Symbol



Belows

Material Max. Temperature


Auto switchReed A/S Model Solid

state A/S Model

Nil None Nil NoneA54 D-A54K F59 D-F59KA56 D-A56K F5P D-F5PKA64 D-A64K J59 D-J59K

A90(V) D-A90(V)K J51 D-J51KA93(V) D-A93(V)K F9N D-F9N(V)KA96(V) D-A96(V)K F9P D-F9P(V)K

F9B D-F9B(V)K Only for auto switch attached type. Refer to Auto Switch Catalogue for more

information.

ACM - N B 80 - S 100

Features

With built-in magnet. (Standard) With non-lubricated seal. Improved cushion ring and special seal increase

the absorbable kinetic energy. Cushion needle avoid detachment.


Ø4025, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900,

950, 1000

2950Ø50Ø63Ø80

Ø100 Other intermediate strokes is available upon request. Refer to page [1]-133, for specifications about custom-made rod ends.

ACM-N B80-S100

KCC Co., Ltd.

www.kccpr.com 661 -


Medium Cylinder

ACM series

TypeNon-lubricated

Low hydraulic pressureSingle rod Double rod

Fluid Air Turbine Oil VG32


Max. operating pressure 9.9kgf/cm2 (0.99MPa) Low pressure L type: 5kgf/cm2 (0.5MPa)

Min. operating pressure 0.5kgf/cm2 (0.05MPa) 1.0kgf/cm2 (0.1MPa)


Operating piston speed 50 ~ 1000mm/sec 0.5 ~ 300mm/sec

Cushion Both side air cushion None


Tolerance of stroke ~250ST : +1.00 251 ~ 800ST : +1.4

0

Bore sizeMounting Ø40 Ø50 Ø63 Ø80 Ø100

Foot LB40 LB50 LB63 LB80 LB100

Flange FA/FB40 FA/FB50 FA/FB63 FA/FB80 FA/FB100

Single clevis (With pin) CA40 CA50 CA63 CA80 CA100

Double clevis (WIth pin) CB40 CB50 CB63 CB80 CB100

Foot mounting basically 2 pcs/set.

Bore sizeRod end attahment Ø40 Ø50,

Ø63 Ø80 Ø100

Single knuckle joint I40 I50/63 I80 I100

Double knuckle joint Y40 Y50/63 Y80 Y100

Speci cations

Accessory

Mounting Style Rod End Attachment

Mounting style Standard Foot Rod Side Flange Head Side Flange Single clevis Double clevis Trunnion

StandardRod end nut

Clevis pin - - - - - -

OptionSingle knuckle jointDouble knuckle joint

Bellows

For double clevis type & double knuckle joint type, pin and snap ring are included.

MassUnit: kg

Bore size (mm)Double acting single rod Double acting double rod

Ø40 Ø50 Ø63 Ø80 Ø100 Ø40 Ø50 Ø63 Ø80 Ø100

Basis mass

Standard 0.790 1.134 1.408 2.636 3.536 0.904 1.277 1.580 3.003 3.956

Foot 0.962 1.342 1.712 3.328 4.364 1.076 1.485 1.884 3.695 4.784

Flange 0.924 1.302 1.684 3.150 4.218 1.038 1.445 1.856 3.517 4.638

Single clevis 1.048 1.506 2.146 3.910 5.524 - - - - -

Double clevis (with pin) 1.076 1.596 2.102 4.024 5.694 - - - - -

Trunnion 1.150 1.614 2.208 4.186 7.206 1.264 1.757 2.380 4.553 7.626

Additional mass per each 50mm of stroke 0.168 0.212 0.268 0.456 0.604 0.252 0.277 0.347 0.662 0.906

Accessory

Single knuckle joint 0.166 0.226 0.226 0.488 0.676 - - - - -

Double knuckle joint (with pin) 0.220 0.296 0.296 0.638 0.916 - - - - -

Rod nut 0.016 0.032 0.032 0.048 0.116 - - - - -

Ex) ACM-LB40-S100 Basis mass: 0.962(Foot Ø40) / Addtional mass: 0.168/50 / Stroke: 100mm

0.962+0.168/50X100 = 1.298kg

Calculation:

KCC Co., Ltd.

www.kccpr.com 671 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Medium Cylinder

ACM series


1 Rod Cover Aluminium Alloy -

2 Head Cover Aluminium Alloy -

3 Cylinder Tube Aluminium Alloy Hard Anodized Alluminium

4 Piston (Rod Side) Aluminium Alloy -

5 Rod Carbon SteelHard

Chromium Plating

6 Bush Copper -

7 Cushon Needle Stainless Steel -

8 Tie Rod Carbon Steel Zinc Plating

9 Spring Washer HSWR -

10 Tie Rod Nut Carbon Steel Zinc Plating

11 Rod End Nut Rolled Steel Zinc Plating

12 Piston(Head Side) Aluminium Alloy -

Type No. Parts MaterialBore size (mm)

40 50 63 80 100

Non-lubricated

13Non-

lubricated packing

NBR

OPA40 OPA50 OPA63 OPA80 OPA100

14 Tube O-ring Ø38X1.5 Ø48X1.5 S60 S77 S97

15 Cushion packing KP20 KP24 KP24 KP30 KP35

16 Rod packing DRP16 DRP20 DRP20 DRP25 DRP30

17 Needle O-ring AN5 AN5 AN5 AN5 AN5

18 Magnet Ø40 Ø50 Ø63 Ø80 Ø100

19 Rod O-ring S10 S14 S14 S16 S20

20 Wearing Resin SWB40 SWB50 SWB63 SWB80 SWB100

Low hyd. pressure 1) 21

Low hyd. pressure packing

NBR HSD40 HSD50 HSD63 HSD80 HSD100

1) All packings are non-lubricated type except no. 21.

Structure

Standard (Non Lubricated type) ACM N-B

Low Hydraulic Pressure type ACM L

* New version cover has a longer cushion length. It is a patented model.

KCC Co., Ltd.

www.kccpr.com 681 -

PNEUMATIC & HYDRAULIC ACM seriesMedium Cylinder

Unit : mm

Bore size Effective thread length A B C CA CB ØD ØEA H KK L N PA

Ø40 27 30 6 44 17.5 8.5 16 32 12 M14XP1.5 84 M8XP1.25 15.4

Ø50 32 35 7 52 19.5 11 20 40 12 M18XP1.5 90 M8XP1.25 14

Ø63 32 35 7 64 23 11 20 40 12 M18XP1.5 98 M8XP1.25 15

Ø80 37 40 11 78 24 14 25 52 17 M22XP1.5 116 M12XP1.75 17.5

Ø100 37 40 11 92 26.5 14.5 30 52 17 M26XP1.5 126 M12XP1.75 20

Unit : mm

Bore size Effective thread length A B C CA CB ØD ØEA H K KK L ØLD LH

Ø40 27 30 6 44 17.5 8.5 16 32 12 60 M14XP1.5 84 9 40

Ø50 32 35 7 52 19.5 11 20 40 12 70 M18XP1.5 90 9 45

Ø63 32 35 7 64 23 11 20 40 12 85 M18XP1.5 98 11.5 50

Ø80 37 40 11 78 24 14 25 52 17 102 M22XP1.5 116 13.5 65

Ø100 37 40 11 92 26.5 14.5 30 52 17 116 M26XP1.5 126 13.5 75

Bore size PB Rc(PT) T T TL V W

Ø40 6.5 1/4 51 60 138 3 26

Ø50 8 3/8 58 70 151 3 27.5

Ø63 8 3/8 58 83 159 3 29.5

Ø80 13 1/2 71 102 194 7 34

Ø100 13 1/2 72 116 205 7 36.5

Bore size LS LT LX LY N PA PB Rc(PT) T T TL W X Y

Ø40 138 3 42 70 M8XP1.25 15.4 6.5 1/4 51 60 175 26 27 (13)

Ø50 144 3 50 80 M8XP1.25 14 8 3/8 58 70 188 27.5 27 (13)

Ø63 166 3 59 93 M8XP1.25 15 8 3/8 58 83 206 29.5 34 (16)

Ø80 204 5 76 116 M12XP1.75 17.5 13 1/2 71 102 247 34 44 (16)

Ø100 212 5 92 133 M12XP1.75 20 13 1/2 72 116 258 36.5 43 (17)





KCC Co., Ltd.

www.kccpr.com 691 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

ACM seriesMedium Cylinder

Unit : mm

Bore size Effective thread length A B C CA CB ØD ØEA FD FQ FT FX FY FZ

Ø40 27 30 6 44 17.5 8.5 16 32 9 65 12 80 42 100

Ø50 32 35 7 52 19.5 11 20 40 9 75 12 90 50 110

Ø63 32 35 7 64 23 11 20 40 11.5 90 15 105 59 130

Ø80 37 40 11 78 24 14 25 52 13.5 110 18 130 76 160

Ø100 37 40 11 92 26.5 14.5 30 52 13.5 126 18 150 92 180

Bore size KK L N PA PB Rc(PT) T T TL V W

Ø40 M14XP1.5 84 M8XP1.25 15.4 6.5 1/4 51 60 138 3 26

Ø50 M18XP1.5 90 M8XP1.25 14 8 3/8 58 70 151 3 27.5

Ø63 M18XP1.5 98 M8XP1.25 15 8 3/8 58 83 159 3 29.5

Ø80 M22XP1.5 116 M12XP1.75 17.5 13 1/2 71 102 194 7 34

Ø100 M26XP1.5 126 M12XP1.75 20 13 1/2 72 116 205 7 36.5

Unit : mm

Bore size Effective thread length A B C CA CB ØD ØEA ØFD FQ FT FX FY FZ H

Ø40 27 30 6 44 17.5 8.5 16 32 9 65 12 80 42 100 12

Ø50 32 35 7 52 19.5 11 20 40 9 75 12 90 50 110 12

Ø63 32 35 7 64 23 11 20 40 11.5 90 15 105 59 130 12

Ø80 37 40 11 78 24 14 25 52 13.5 110 18 130 76 160 17

Ø100 37 40 11 92 26.5 14.5 30 52 13.5 126 18 150 92 180 17

Bore size KK L N PA PB Rc(PT) T T TL W

Ø40 M14XP1.5 84 M8XP1.25 15.4 6.5 1/4 51 60 147 26

Ø50 M18XP1.5 90 M8XP1.25 14 8 3/8 58 70 160 27.5

Ø63 M18XP1.5 98 M8XP1.25 15 8 3/8 58 83 171 29.5

Ø80 M22XP1.5 116 M12XP1.75 17.5 13 1/2 71 102 205 34

Ø100 M26XP1.5 126 M12XP1.75 20 13 1/2 72 116 216 36.5





KCC Co., Ltd.

www.kccpr.com 701 -


Unit : mm

Bore size Effective thread length A B C CA CB ØCD CL CV CX ØD ØEA H

Ø40 27 30 6 44 17.5 8.5 10 +0.15+0.10 30 18 15.0 -0.1

-0.3 16 32 12

Ø50 32 35 7 52 19.5 11 12 +0.15+0.10 35 23 18.0 -0.1

-0.3 20 40 12

Ø63 32 35 7 64 23 11 16 +0.15+0.10 40 27 25.0 -0.1

-0.3 20 40 12

Ø80 37 40 11 78 24 14 20 +0.15+0.10 48 34 31.5 -0.1

-0.3 25 52 17

Ø100 37 40 11 92 26.5 14.5 25 +0.15+0.10 58 43 35.5 -0.1

-0.3 30 52 17

Unit : mm

Bore size Effective thread length A B C CA CB ØCD CL CV CX CZ ØD ØEA

Ø40 27 30 6 44 17.5 8.5 10 +0.15+0.10 30 18 15.0 +0.1

+0.3 29.5 16 32

Ø50 32 35 7 52 19.5 11 12 +0.15+0.10 35 23 18.0 +0.1

+0.3 38 20 40

Ø63 32 35 7 64 23 11 16 +0.15+0.10 40 27 25.0 +0.1

+0.3 49 20 40

Ø80 37 40 11 78 24 14 20 +0.15+0.10 48 34 31.5 +0.1

+0.3 61 25 52

Ø100 37 40 11 92 26.5 14.5 25 +0.15+0.10 58 43 35.5 +0.1

+0.3 64 30 52

Bore size KK L N PA PB R Rc(PT) T T TZ W

Ø40 M14XP1.5 84 M8XP1.25 15.4 6.5 (10) 1/4 51 60 165 26

Ø50 M18XP1.5 90 M8XP1.25 14 8 (12) 3/8 58 70 183 27.5

Ø63 M18XP1.5 98 M8XP1.25 15 8 (16) 3/8 58 83 196 29.5

Ø80 M22XP1.5 116 M12XP1.75 17.5 13 (20) 1/2 71 102 235 34

Ø100 M26XP1.5 126 M12XP1.75 20 13 (25) 1/2 72 116 256 36.5

Bore size H KK L N PA PB R Rc(PT) T T TZ W

Ø40 12 M14XP1.5 84 M8XP1.25 15.4 6.5 (10) 1/4 51 60 165 26

Ø50 12 M18XP1.5 90 M8XP1.25 14 8 (12) 3/8 58 70 183 27.5

Ø63 12 M18XP1.5 98 M8XP1.25 15 8 (16) 3/8 58 83 196 29.5

Ø80 17 M22XP1.5 116 M12XP1.75 17.5 13 (20) 1/2 71 102 235 34

Ø100 17 M26XP1.5 126 M12XP1.75 20 13 (25) 1/2 72 116 256 36.5





KCC Co., Ltd.

www.kccpr.com 711 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Unit : mm

Bore size Effective thread length A B C CA CB ØD ØEA H KK L LZ N

Ø40 27 30 6 44 17.5 8.5 16 32 12 M14XP1.5 84 93 M8XP1.25

Ø50 32 35 7 52 19.5 11 20 40 12 M18XP1.5 90 103 M8XP1.25

Ø63 32 35 7 64 23 11 20 40 12 M18XP1.5 98 107 M8XP1.25

Ø80 37 40 11 78 24 14 25 52 17 M22XP1.5 116 129 M12XP1.75

Ø100 37 40 11 92 26.5 14.5 30 52 17 M26XP1.5 126 135 M12XP1.75

Bore size PA PB Rc(PT) T T ØTD TL TT TX TY TZ V W Z ZZ

Ø40 15.4 6.5 1/4 51 60 15 -0.05-0.10 138 22 85 62 117 3 26 88 98

Ø50 14 8 3/8 58 70 15 -0.05-0.10 151 22 95 74 127 3 27.5 96.5 109.5

Ø63 15 8 3/8 58 83 18 -0.05-0.10 158 28 110 90 148 3 29.5 101.5 111.5

Ø80 17.5 13 1/2 71 102 25 -0.05-0.10 194 34 140 110 192 7 34 122 136

Ø100 20 13 1/2 72 116 25 -0.05-0.10 205 40 162 130 214 7 36.5 128.5 141.5

Dimensions-Center Trunnion (TC), Rod Side Trunnion (TA), Head Side Trunnion (TB)


Rod Side Trunnion (TA)

Center Trunnion (TC)

Head Side Trunnion (TB)

KCC Co., Ltd.

www.kccpr.com 721 -


Unit : mm

Part No. Bore size TA TC TDH10 (Hole) TE TF TH TL TO TR TS TT

KA2-40/50Ø40 80 102 15 +0.070

0 119 60 45 60 17 9 12 17

Ø50 80 112 15 +0.0700 129 60 45 60 17 9 12 17

KA2-63 Ø63 100 130 18 +0.0700 150 73 55 70 20 11 14 22

KA2-80/100Ø80 120 166 25 +0.084

0 192 100 75 90 26 13.5 17 24

Ø100 120 188 25 +0.0840 214 100 75 90 26 13.5 17 24

Part No. TU TX TY Z

KA2-40/5010 85 62 93

10 95 74 103

KA2-63 15 110 90 107

KA2-80/10015 140 110 129

15 162 130 135

Unit : mm

Part No. Bore size B DA DC DDH10 (Hole) DE DF DH DL DO DR DS

CB2-40 Ø40 60 57 65 10 +0.0580 85 52 40 35 10 9 8

CB2-50 Ø50 70 57 65 12 +0.0700 85 52 40 35 10 9 8

CB2-63 Ø63 85 67 80 16 +0.0700 105 66 50 40 12.5 11 10

CB2-80 Ø80 102 93 100 20 +0.0840 130 90 65 60 15 13.5 12

CB2-100 Ø100 116 93 100 25 +0.0840 130 90 65 60 15 13.5 12

Part No. DT DU DX Z

CB2-40 17 11 15 165

CB2-50 17 11 18 183

CB2-63 22 13.5 25 196

CB2-80 24 16.5 31.5 235

CB2-100 24 16.5 35.5 256

Bore size (mm) A B A + B + 90

Ø40~Ø100 12 60 162

Dimensions-Trunnion Bracket (KA2)

Dimensions-Double Clevis Bracket (CB2)

Rotating Angle

KCC Co., Ltd.

www.kccpr.com 731 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Unit : mmPart No.

Bore size ØE F KK L LS ØND NX R V

I40 Ø40 24 22 M14X1.5 55 69 12 +0.070 16 -0.1

-0.3 15.5 20

I50 Ø50, 63 28 27 M18X1.5 60 74 12 +0.070 16 -0.1

-0.3 15.5 20

I80 Ø80 36 37 M22X1.5 71 91 18 +0.070 28 -0.1

-0.3 22.5 26

I100 Ø100 40 37 M26X1.5 83 105 20 +0.080 30 -0.1

-0.3 24.5 28

Unit : mm

Part No. Bore size ØDd9 Ød L m t

JP-04 Ø40, 50, 63 12 -0.05-0.09 Ø11 44.5 38.2 1.85 1.13

JP-08 Ø80 18 -0.05-0.09 Ø16.5 62.5 55.2 2.15 1.35

JP-10 Ø100 20 -0.06-0.12 Ø18.5 68.2 61.2 2.15 1.35

Unit : mm

Part No. Bore size ØDd9 Ød L m t

CP-04 Ø40 10 -0.04-0.09 Ø9 35.8 29.8 1.85 1.15

CP-05 Ø50 12 -0.04-0.09 Ø11 44.5 38.2 1.9 1.15

CP-06 Ø63 16 -0.05-0.09 Ø14.5 55.3 49.2 1.9 1.15

CP-08 Ø80 20 -0.06-0.11 Ø18.5 68.2 61.2 2.15 1.35

CP-10 Ø100 25 -0.06-0.11 Ø23 71.2 64.2 2.15 1.35



Unit : mm

Part No. Bore size C ØD H KK T

RN-04 Ø40 25.4 21 22 M14X1.5 8

RN-05 Ø50, 63 31.2 26 27 M18X1.5 11

RN-08 Ø80 37.0 31 32 M22X1.5 13

RN-10 Ø100 47.3 39 41 M26X1.5 16

Rod End Nut Clevis Pin

Knuckle Joint Pin

Unit : mmPart No.

Bore size ØE F KK L ØND NX NZ R V

Y40 Ø40 24 22 M14X1.5 55 12 +0.10 16 +0.3

+0.1 38 15.5 30

Y50 Ø50, 63 28 24 M18X1.5 60 12 +0.10 16 +0.3

+0.1 38 15.5 30

Y80 Ø80 36 33 M22X1.5 71 18 +0.10 28 +0.3

+0.1 55 22.5 43

Y100 Ø100 40 34 M26X1.5 83 20 +0.10 30 +0.3

+0.1 61 24.5 45



Material: Rolled steel

Material: Carbon steel


Material: FC 40

KCC Co., Ltd.

www.kccpr.com 741 -


Unit : mm

Bore size C CA CB ØEA ØEB KK L N PA PB Rc(PT) S

Ø40 44 17.5 8.5 32 43 M14XP1.5 84 M8XP1.25 15.4 6.5 1/4 1/4 stroke

Ø50 52 19.5 11 40 52 M18XP1.5 90 M8XP1.25 14 8 3/8 1/4 stroke

Ø63 64 23 11 40 52 M18XP1.5 98 M8XP1.25 15 8 3/8 1/4 stroke

Ø80 78 24 14 52 65 M22XP1.5 116 M12XP1.75 17.5 13 1/2 1/4 stroke

Ø100 92 26.5 14.5 52 65 M26XP1.5 126 M12XP1.75 20 13 1/2 1/4 stroke

Bore size T T TL V W

Ø40 59 60 146 3 26

Ø50 66 70 159 3 27.5

Ø63 66 83 166 3 29.5

Ø80 80 102 203 7 34

Ø100 81 116 214 7 36.5

For dimensions not shown in these figures, refer to the ACM (Standard) type. SUS band is mounted at bellows at delivery.



Unit : mm

Bore size Effective thread length A B CA CB ØD H KK L PA PB Rc(PT)

Ø40 27 30 6 18 8 16 12 M14XP1.5 84 12.5 6.5 1/4

Ø50 32 35 7 19.5 11 20 12 M18XP1.5 90 14 8 3/8

Ø63 32 35 7 23 11 20 12 M18XP1.5 98 15 9 3/8

Ø80 37 40 11 25 12 25 17 M22XP1.5 116 19 12 1/2

Ø100 37 40 11 27.5 12 30 17 M26XP1.5 126 20 12 1/2

Bore size T TL W

Ø40 51 186 26.5

Ø50 58 206 27.5

Ø63 58 214 29.5

Ø80 71 258 34

Ø100 72 270 36.5

For dimensions not shown in these figues, refer to the ACM (Standard) type.

Dimensions-Double Rod (ACMW)


Type J K


Heat resistant 60 110

KCC Co., Ltd.

www.kccpr.com 751 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Unit : mmBore size L TL

Ø40 168 222

Ø50 180 241

Ø63 196 257

Ø80 232 310

Ø100 252 330



Dimensions-Single Rod Multi-Step Stroke Cylinder (TS)




Unit : mm

Bore size L TL

Ø40 168 270

Ø50 180 296

Ø63 196 312

Ø80 232 374

Ø100 252 396










KCC Co., Ltd.

www.kccpr.com 761 -


Unit : mmBore size L TL

Ø40 168 222

Ø50 180 241

Ø63 196 257

Ø80 232 310

Ø100 252 330

Fo r d imens ions no t shown in these figues, refer to the ACM (Standard) type.


Unit : mmBore size ØB C D ZZ

Ø40 Ø32 22 46 181

Ø50Ø42

28 58.5 206.5

Ø63 28 54 210

Ø80Ø50

35 70 257

Ø100 35 70 268








Dimensions-Stroke Adjustable Type (ASJ, BSJ)


Stroke Adjustable Cylinder (ASJ, BSJ)




Range of adjustment

KCC Co., Ltd.

www.kccpr.com 771 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Heat resistant cylinder can be used at a high ambient temperature up to150 by equipped with heat-resistant seal.

Type No lubricated

Bore size Ø40, Ø50, Ø63, Ø80, Ø100

Temperature -20~150



Type Lubricated, No lubricated

Bore size Ø40, Ø50, Ø63, Ø80, Ø100

Rod Material SUS304

Stainless Steel Piston Rod (SS)Head Resistant Cylinder (SV)



Working at low pressure even when sliding resistance is low. Smooth operation is available even in low speed.

Lubrication No lubriacatedDirection of low

friction operation Single direction (R-Air supply, H-Air supply)

Proof Pressure 10.5kgf/cm2 (1.05MPa)Max. operating

pressure 9.9kgf/cm2 (0.99MPa)


Cushion None

Inner leakage Below 0.5 I/min (ANR)


1. When used as a balancer etc., follow the example of the application mentioned earlier applying pressure at one port while leaving the other port open to atmosphere.With pressure at rod cover port·········· Low friction side B (Example of application )With pressure at head cover port·········· Low friction side F (Example of application )

2. In both cases, as long as the outside pressure moves the piston rod, low friction can result in the direction of extension and retraction.

Low Friction Cylinder (Q)

Speci cations

Sliding Resistance of Low Friction Side

Dimensions-Low Friction Type (ACM Q)

Applications

Unit : mmBore size L T TL

Ø40 94 51 148

Ø50 100 58 161

Ø63 108 58 169

Ø80 126 71 204

Ø100 136 72 215

0.02

0.025

0.01

0 0.01 0.1 0.2 0.3 0.4 0.5 0.6 0.7

Bore Size

(Con

verte

d int

o re

sista

nce

for e

ach

cylin

der)

Slidi

ng re

sista

nce

(MPa

)

Operating pressure (MPa)

Driving rollerWinding roller

Precision regulator

Moving body

Precision regulator

KCC Co., Ltd.

www.kccpr.com 781 -


Large Cylinder

ACL series

ACL series

Series

ACL Double acting single rod large cylinder

ACLW Double acting double rod large cylinder

Cover materialØ125~Ø200 Ø250~Ø300

Nil AL(Standard) Steel(Standard)FC Steel -

Bellows



Rod end attachmentNil Rod end nut(Standard) : 1pcI Single knuckle jointY Double knuckle joint

Mounting styleB Standard CB Double Clevis

LB Foot TC Center TrunnionFA Rod Side Flange TA Rod Side TrunnionFB Head Side Flange TB Head Side TrunnionCA Single Clevis

LubricationNil LubricatedN Non lubricated (Standard)

L Low hydraulic pressure( 5kgf/cm2)

G Low hydraulic pressure ( 25kgf/cm2)

MagnetNil Without built-in magnetH Built-in magnet

Tube materialNil ALF Steel



Special OrderNil None

TS Multi-step stroke cylinder (Single rod)

TW Multi-step stroke cylinder (Double rod)

TD Tandem cylinder




How to Order

ACL-B 140-S125

ACL - B 140 - S 125

Symbol




state A/S Model

A54 D-A54K F59 D-F59KA56 D-A56K F5P D-F5PKA64 D-A64K J59 D-J59K


F9B D-F9B(V)K Only for auto switch attached type. Refer to Auto Switch Catalogue for more information.


Ø125 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500

2950Ø140 25, 50, 75, 100, 125, 150, 175, 200, 250, 300

Ø150 25, 50, 75, 100, 125, 150, 175, 200, 250, 300, 350, 400, 450, 500

Ø160 25, 50, 75, 100, 125, 150, 175, 200, 250, 300Ø180 25, 50, 75, 100, 125, 150, 175, 200, 250, 300

-Ø250 50, 100, 150, 200, 250, 300Ø300 -

Other intermediate strokes available on request.

Features

Aluminum tube available for Ø125~Ø300. Ligher weight & auto switch type available. Steel tube : Ø250~Ø300 Excellent durability and performance. Various mounting styles.


Bore size125 140 150 160

Ø125 Ø140 Ø150 Ø160180 200 250 300

Ø180 Ø200 Ø250 Ø300

KCC Co., Ltd.

www.kccpr.com 791 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Large Cylinder

ACL series

AccessoryType Double acting single rod

Mounting style Standard Foot Rod side ange

Head side ange

Single clevis

Double clevis

Center trunnion

Standard mounting

Rod end nut

Clevis pin - - - - - -

Option



Bellows

For double clevis and double knuckle joint, pin and snap ring are included.

Bore sizeMounting style Ø125 Ø140 Ø150 Ø160 Ø180 Ø200 Ø250 Ø300

Foot LB125 LB140 LB150 LB160 LB180 LB200 LB250 LB300

Flange FA/FB125

FA/FB140

FA/FB150

FA/FB160

FA/FB180

FA/FB200

FA/FB250

FA/FB300

Single clevis (with pin) CA125 CA140 CA150 CA160 CA180 CA200 CA250 CA300

Double clevis (with pin) CB125 CB140 CB150 CB160 CB180 CB200 CB250 CB300

For foot type mounting, 2 pieces in one set.

Mounting Style

Bore sizeRod end attachment Ø125 Ø140 Ø150,

Ø160 Ø180 Ø200 Ø250 Ø300

Single knuckle joint I125 I140 I150/160 I180 I200 I250 I300

Double knuckle joint Y125 Y140 Y150/160 Y180 Y200 Y250 Y300

Rod End Attachment

Speci cationsType Lubricated, Non-lubricated Low hydraulic pressure

Fluid Air Turbine Oil VG32


Max. operating pressure 9.9kgf/cm2 (0.99MPa) Low pressure L type:5kgf/cm2 (0.5MPa)

Min. operating pressure 0.8kgf/cm2 (0.08MPa) 1kgf/cm2 (0.1MPa)Ambient & uid

temperature 5 ~ 60

Operating piston speed 50 ~ 500mm/sec 0.5 ~ 200mm/sec

Cushion With cushion Without cushion


Tolerance of stroke ~250ST: +1.00 251 ~ 1000ST: +1.4

0 1001 ~ 1500ST: +1.80

KCC Co., Ltd.

www.kccpr.com 801 -


Large Cylinder

ACL series

Mass

1. Double acting single rod (Aluminium tube) Ex) ACL-LB160-S500

Basic mass: 14.70(FootØ160) / Additional mass: 2.20/100 / Cylinder stroke: 500mm 14.70 + 2.20/100 X 500 = 25.70kg

2. Double acting double rod (Aluminium tube) Ex) ACLW-LB125-S500

Basic mass: 7.78(FootØ125) / Additional mass: 2.37/100 / Cylinder stroke: 500mm 7.78 + 2.37/100 X 500 = 19.63kg

Calculation:

Unit: kg

Bore size (mm)

Aluminium tube

Double acting single rod Double acting double rod

Ø125 Ø140 Ø150 Ø160 Ø125 Ø140 Ø150 Ø160

Standard 5.38 6.76 8.82 11.78 5.98 7.38 9.49 12.67

Foot 7.18 8.92 11.58 14.70 7.78 9.54 12.25 15.59

Flange 8.32 12.40 14.96 18.80 8.92 13.02 15.63 19.69

Single clevis 8.60 11.42 14.40 17.76 - - - -

Double clevis (with pin) 8.88 11.74 15.10 18.28 - - - -

Trunnion 9.51 12.49 15.77 19.18 10.11 13.11 16.44 20.07

Additional mass for each 100mm stroke 1.68 1.68 2.16 2.20 2.37 2.44 3.05 3.11


Double knuckle joint (with pin) 1.37 1.88 2.43 2.43 - - - -

Rod end nut 0.16 0.16 0.26 0.26 - - - -

Bas

ic m

ass

Acc

esso

ry

Unit: kg

Bore size (mm)

Steel tube

Double acting single rod Double acting double rod

Ø125 Ø140 Ø160 Ø180 Ø200 Ø250 Ø300 Ø125 Ø140 Ø160 Ø180 Ø200 Ø250 Ø300

Standard 15.20 18.38 25.24 34.16 42.66 79.78 115.94 16.85 20.03 27.12 36.90 45.79 85.36 122.39

Foot 16.83 20.90 28.04 38.36 47.54 89.28 133.22 18.48 22.55 29.92 41.10 50.67 94.86 139.67

Rod side ange 17.88 23.38 31.63 43.99 54.57 101.62 146.14 - - - - - - -

Head side ange 17.88 23.38 31.63 43.99 54.57 101.62 146.14 - - - - - - -

Single clevis 18.27 22.67 30.73 42.55 52.56 98.17 149.22 - - - - - - -

Double clevis (with pin) 18.73 23.42 34.58 44.23 54.59 101.36 154.96 - - - - - - -

Trunnion 19.33 24.11 32.64 44.78 56.65 107.62 156.37 20.98 25.76 34.52 47.52 59.78 113.20 162.82

Additional mass for each 100mm stroke 2.66 3.01 3.58 4.95 5.75 9.08 12.15 3.46 3.81 4.57 6.20 7.29 11.30 15.17

Single knuckle joint 0.91 1.16 1.56 3.07 2.90 5.38 10.82 - - - - - - -

Double knuckle joint (with pin) 1.37 1.81 2.48 4.74 4.59 9.22 17.17 - - - - - - -

Rod end nut 0.16 0.16 0.2 0.32 0.85 1.26 1.43 - - - - - - -

Bas

ic m

ass

Acc

esso

ry

KCC Co., Ltd.

www.kccpr.com 811 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Large Cylinder

ACL series


1 Rod CoverAL Alloy Ø125~Ø160

Rolled Steel Sheet Ø180~Ø300

2 Head CoverAL Alloy Ø125~Ø160

Rolled Steel Sheet Ø180~Ø300

3Tube

Ø125~Ø160Ø180~Ø300

AL Alloy Hard Anodized Aluminium

Carbon Steel Tube

Hard Chromium Plating

4 PistonAL Alloy Ø125~Ø160

Cast Iron Ø180~Ø300


6 Secondary Block (Ø180~Ø300) Cast Iron Black Oxide

Coating

7 Bush DU Bush -

8 Cushion Needle Brass -

9 Tie Rod Carbon Steel Zinc Plating

10 Spring Washer Hard Steel Wire -

11 Tie Rod Nut Carbon Steel Zinc Plating

12 Secondary Block Grey Cast Iron -

13 Spring Bolt of Secondary Block

Chrome-Molybdenum

Steel -

14 Cushion Ring (Rod Side) Carbon Steel -

15 Cushion Ring(Head Side) Carbon Steel -

16 Rod End Nut Rolled Steel -

17 Cushion Needle (Ø180~Ø300) Rolled Steel -

Structure

Non lubricated ACL N

Low hydrualic pressure ACL L

Non lubricated ACL N

Low hydrualic pressure ACL L

Standard (Lubricated type) (Ø125, Ø140, Ø150, Ø160)

Standard (Lubricated type) (Ø180, Ø200, Ø250, Ø300)

Type No. Parts MaterialBore size

125 140 150 160 180 200 250 300

Lubrication

18 Piston Packing

NBR

AP115 AP130 AP140 AP150 AP165 AP185 AP235 AP285

19 Tube O-Ring

Ø125x W2.0

Ø140x W2.0

Ø150x W2.0

Ø160x W2.0

Ø180x W2.0

Ø200x W2.0

Ø250x W2.0

Ø300x W2.0

20 Cushion Packing PCS50 PCS50 PCS55 PCS55 PCS60 PCS60 PCS75 PCS80

21 Rod Packing DRP35 DRP35 DRP40 DRP40 DRP45 DRP50 DRP60 DRP70

22 Bush O-Ring - - - - AP63 AP67 AP80 AP85

23Cushion Needle O-Ring

S10 S10 S10 S10 S10 S10 S10 S10

24 Magnet Ø125 Ø140 Ø150 Ø160 - - - -

25 Rod O-Ring S26 S26 S30 S30 S35 S40 S48 S50

Note1) Non Lubricated

26 Wearing RESIN HWR8 HWR8 HWR8 HWR8 HWR8 HWR8 HWR8 HWR8

27 Piston Packing NBR OPA

125OPA140

OPA150

OPA160

OPA180

OPA200

OPA250

OPA300

Note2) Low Hyd. Pressure 28 Piston

Packing NBR DXP125

DXP140

DXP150

DXP160 - - - -

Note 1) For non lubricated type, wearing 26 and piston packing 27 are applied, while other packing are the same as that of lubricated type.

Note 2) Piston packing for low pressure type cylinder is piston packing 28, while other packing are the same as that of lubricated type.

KCC Co., Ltd.

www.kccpr.com 821 -

PNEUMATIC & HYDRAULIC ACL seriesLarge Cylinder

Unit : mm

Bore size Effective thread length A B C ØD ØEA ØEB H KK L N PG Rc(PT) SW

Ø125 47 50 15 115 35 59 - 42 M30X1.5 98 M14X1.5 16 1/2 -

Ø140 47 50 15 128 35 59 - 42 M30X1.5 98 M14X1.5 16 1/2 -

Ø150 53 56 17 132 40 59 - 43 M36X1.5 106 M16X1.5 17.5 3/4 -

Ø160 53 56 17 144 40 59 - 43 M36X1.5 106 M16X1.5 17 3/4 -

Ø180 60 63 20 162 45 70 115 48 M40X1.5 111 M18X1.5 17 3/4 17

Ø200 60 63 20 182 50 74 115 48 M45X1.5 111 M20X1.5 16.5 3/4 17

Ø250 67 71 25 225 60 96 140 60 M56X2.0 141 M24X1.5 22 1 20

Ø300 76 80 30 270 70 96 140 60 M64X2.0 146 M30X1.5 22 1 20

Bore size T T TL U W

Ø125 145 110 235 (21) 34

Ø140 161 110 235 (21) 34

Ø150 170 120 256.5 (23) 38

Ø160 184 120 256.5 (23) 38

Ø180 204 135 281 (26) 39

Ø200 226 135 281 (30) 39

Ø250 277 160 342.5 (34) 49

Ø300 330 175 372.5 (41.5) 49


Only for 125 of ACL series



Ø125, Ø140, Ø150, Ø160

Ø180, Ø200, Ø250, Ø300

KCC Co., Ltd.

www.kccpr.com 831 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

ACL seriesLarge Cylinder

Unit : mm

Bore size Effective thread length A AA B C ØD ØEA ØEB H KK L ØLD LH LS LT

Ø125 47 50 145 15 115 35 59 - 42 M30X1.5 98 19 85 188 8

Ø140 47 50 161 15 128 35 59 - 42 M30X1.5 98 19 100 188 9

Ø150 53 56 170 17 132 40 59 - 43 M36X1.5 106 19 105 206 9

Ø160 53 56 184 17 144 40 59 - 43 M36X1.5 106 19 106 206 9

Ø180 60 63 204 20 162 45 70 115 48 M40X1.5 111 24 125 231 10

Ø200 60 63 226 20 182 50 74 115 48 M45X1.5 111 24 132 231 10

Ø250 67 71 277 25 225 60 96 140 60 M56X2.0 141 29 160 301 12

Ø300 76 80 330 30 270 70 96 140 60 M64X2.0 146 33 200 326 15

Bore size LX LY N PG Rc(PT) SW T T TL W X Y

Ø125 100 157.5 M14X1.5 16 1/2 - 110 145 273 34 45 (20)

Ø140 112 180.5 M14X1.5 16 1/2 - 110 161 273 34 45 (20)

Ø150 118 190 M16X1.5 17.5 3/4 - 120 170 301 38 50 (25)

Ø160 118 197 M16X1.5 17 3/4 - 120 184 301 38 50 (25)

Ø180 132 227 M18X1.5 17 3/4 17 135 204 336 39 60 (30)

Ø200 150 245 M20X1.5 16.5 3/4 17 135 226 336 39 60 (30)

Ø250 180 298.5 M24X1.5 22 1 20 160 277 421 49 80 (40)

Ø300 212 365 M30X1.5 22 1 20 175 330 451 49 90 (40)





Ø125, Ø140, Ø150, Ø160

Ø180, Ø200, Ø250, Ø300

KCC Co., Ltd.

www.kccpr.com 841 -


Unit : mm

Bore size Effective thread length A B C ØD ØEA ØEB ØFD FT FX FY FZ H KK

Ø125 47 50 15 115 35 59 - 19 14 190 100 230 42 M30X1.5

Ø140 47 50 15 128 35 59 - 19 20 212 112 255 42 M30X1.5

Ø150 53 56 17 132 40 59 - 19 20 228 115 265 43 M36X1.5

Ø160 53 56 17 144 40 59 - 19 20 236 118 275 43 M36X1.5

Ø180 60 63 20 162 45 70 115 24 25 265 132 320 48 M40X1.5

Ø200 60 63 20 182 50 74 115 24 25 280 150 335 48 M45X1.5

Ø250 67 71 25 225 60 96 140 29 30 355 180 420 60 M56X2.0

Ø300 76 80 30 270 70 96 140 33 30 400 212 475 60 M64X2.0

Bore size L N PG Rc(PT) T T TL U W

Ø125 98 M14X1.5 16 1/2 145 110 232 (25) 34

Ø140 98 M14X1.5 16 1/2 161 110 232 (25) 34

Ø150 106 M16X1.5 17.5 3/4 170 120 252 (27) 38

Ø160 106 M16X1.5 17 3/4 184 120 252 (27) 38

Ø180 111 M18X1.5 17 3/4 204 135 277 (30) 39

Ø200 111 M20X1.5 16.5 3/4 226 135 277 (35) 39

Ø250 141 M24X1.5 22 1 277 160 336 (40) 49

Ø300 146 M30X1.5 22 1 330 175 369 (49) 49


Ø125, Ø140, Ø150, Ø160

Ø180, Ø200, Ø250, Ø300




KCC Co., Ltd.

www.kccpr.com 851 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Unit : mm

Bore size Effective thread length A B C ØD ØEA ØEB ØFD FT FX FY FZ H KK

Ø125 47 50 15 115 35 59 - 19 14 190 100 230 42 M30X1.5

Ø140 47 50 15 128 35 59 - 19 20 212 112 255 42 M30X1.5

Ø150 53 56 17 132 40 59 - 19 20 228 115 265 43 M36X1.5

Ø160 53 56 17 144 40 59 - 19 20 236 118 275 43 M36X1.5

Ø180 60 63 20 162 45 70 115 24 25 265 132 320 48 M40X1.5

Ø200 60 63 20 182 50 74 115 24 25 280 150 335 48 M45X1.5

Ø250 67 71 25 225 60 96 140 29 30 355 180 420 60 M56X2.0

Ø300 76 80 30 270 70 96 140 33 30 400 212 475 60 M64X2.0

Bore size L N PG Rc(PT) SW T T TL W

Ø125 98 M14X1.5 16 1/2 - 145 110 222 34

Ø140 98 M14X1.5 16 1/2 - 161 110 228 34

Ø150 106 M16X1.5 17.5 3/4 - 170 120 246 38

Ø160 106 M16X1.5 17 3/4 - 184 120 246 38

Ø180 111 M18X1.5 17 3/4 17 204 135 271 39

Ø200 111 M20X1.5 16.5 3/4 17 226 135 271 39

Ø250 141 M24X1.5 22 1 20 277 160 331 49

Ø300 146 M30X1.5 22 1 20 330 175 351 49





Ø125, Ø140, Ø150, Ø160

Ø180, Ø200, Ø250, Ø300

KCC Co., Ltd.

www.kccpr.com 861 -


Unit : mm

Bore size Effective thread length A B C ØCD CL CT CV CX ØD ØEA ØEB H

Ø125 47 50 15 115 25 +0.100 65 17 48 32 -0.1

-0.3 35 59 - 42

Ø140 47 50 15 128 28 +0.100 75 17 58 36 -0.1

-0.3 35 59 - 42

Ø150 53 56 17 132 32 +0.100 80 20 60 40 -0.1

-0.3 40 59 - 43

Ø160 53 56 17 144 32 +0.100 80 20 60 40 -0.1

-0.3 40 59 - 43

Ø180 60 63 20 162 40 +0.100 90 23 67 50 -0.1

-0.3 45 70 115 48

Ø200 60 63 20 182 40 +0.100 90 25 65 50 -0.1

-0.3 50 74 115 48

Ø250 67 71 25 225 50 +0.100 110 30 80 63 -0.1

-0.3 60 96 140 60

Ø300 76 80 30 270 63 +0.120 130 37 93 80 -0.1

-0.3 70 96 140 60

Bore size KK L N PG Rc(PT) R SW T T TL TZ W

Ø125 M30X1.5 98 M14X1.5 16 1/2 29 - 145 110 302 273 34

Ø140 M30X1.5 98 M14X1.5 16 1/2 32 - 161 110 315 283 34

Ø150 M36X1.5 106 M16X1.5 17.5 3/4 36 - 170 120 342 306 38

Ø160 M36X1.5 106 M16X1.5 17 3/4 36 - 184 120 342 306 38

Ø180 M40X1.5 111 M18X1.5 17 3/4 44 17 204 135 380 336 39

Ø200 M45X1.5 111 M20X1.5 16.5 3/4 44 17 226 135 380 336 39

Ø250 M56X2.0 141 M24X1.5 22 1 55 20 277 160 466 411 49

Ø300 M64X2.0 146 M30X1.5 22 1 68 20 330 175 519 451 49


Ø125, Ø140, Ø150, Ø160

Ø180, Ø200, Ø250, Ø300




KCC Co., Ltd.

www.kccpr.com 871 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Unit : mm

Bore size Effective thread length A B C ØCD CL CT CV CX CZ ØD ØEA ØEB H

Ø125 47 50 15 115 25 +0.15+0.10 65 17 48 64 32 +0.3

+0.1 35 59 - 42

Ø140 47 50 15 128 28 +0.15+0.10 75 17 58 72 36 +0.3

+0.1 35 59 - 42

Ø150 53 56 17 132 32 +0.15+0.10 80 20 60 80 40 +0.3

+0.1 40 59 - 43

Ø160 53 56 17 144 32 +0.15+0.10 80 20 60 80 40 +0.3

+0.1 40 59 - 43

Ø180 60 63 20 162 40 +0.15+0.10 90 23 67 100 50 +0.3

+0.1 45 70 115 48

Ø200 60 63 20 182 40 +0.15+0.10 90 25 65 100 50 +0.3

+0.1 50 74 115 48

Ø250 67 71 25 225 50 +0.15+0.10 110 30 80 126 63 +0.3

+0.1 60 96 140 60

Ø300 76 80 30 270 63 +0.15+0.10 130 37 93 160 80 +0.3

+0.1 70 96 140 60

Bore size KK L N PG R Rc(PT) SW T T TL TZ W

Ø125 M30X1.5 98 M14X1.5 16 (29) 1/2 - 145 110 302 273 34

Ø140 M30X1.5 98 M14X1.5 16 (32) 1/2 - 161 110 315 283 34

Ø150 M36X1.5 106 M16X1.5 17.5 (36) 3/4 - 170 120 342 306 38

Ø160 M36X1.5 106 M16X1.5 17 (36) 3/4 - 184 120 342 306 38

Ø180 M40X1.5 111 M18X1.5 17 (44) 3/4 17 204 135 380 336 39

Ø200 M45X1.5 111 M20X1.5 16.5 (44) 3/4 17 226 135 380 336 39

Ø250 M56X2.0 141 M24X1.5 22 (55) 1 20 277 160 466 411 49

Ø300 M64X2.0 146 M30X1.5 22 (68) 1 20 330 175 519 451 49





Ø125, Ø140, Ø150, Ø160

Ø180, Ø200, Ø250, Ø300

KCC Co., Ltd.

www.kccpr.com 881 -


Unit : mm

Bore size Effective thread length A B C ØD ØEA ØEB H KK L LZ N PG Rc(PT)

Ø125 47 50 15 115 35 59 - 42 M30X1.5 98 159 M14X1.5 16 1/2

Ø140 47 50 15 128 35 59 - 42 M30X1.5 98 159 M14X1.5 16 1/2

Ø150 53 56 17 132 40 59 - 43 M36X1.5 106 173 M16X1.5 17.5 3/4

Ø160 53 56 17 144 40 59 - 43 M36X1.5 106 173 M16X1.5 17 3/4

Ø180 60 63 20 162 45 70 115 48 M40X1.5 111 190.5 M18X1.5 17 3/4

Ø200 60 63 20 182 50 74 115 48 M45X1.5 111 190.5 M20X1.5 16.5 3/4

Ø250 67 71 25 225 60 96 140 60 M56X2.0 141 230.5 M24X1.5 22 1

Ø300 76 80 30 270 70 96 140 60 M64X2.0 146 248 M30X1.5 22 1

Bore size RR RT SW T T ØTD TL TX ØTY TZ U W Z ZZ

Ø125 1 50 - 145 110 32 -0.05-0.10 227 170 164 234 (19) 34 170 148

Ø140 1.5 55 - 161 110 36 -0.05-0.10 227 190 184 262 (21.5) 34 172.5 145.5

Ø150 1.5 59 - 170 120 40 -0.05-0.10 248 200 192 275 (22.5) 38 188.5 157.5

Ø160 1.5 59 - 184 120 40 -0.05-0.10 248 212 204 292 (22.5) 38 189 157

Ø180 2 60 17 204 135 45 -0.05-0.10 272.5 236 228 326 (24.5) 39 204 177

Ø200 2 60 17 226 135 45 -0.05-0.10 272.5 265 257 355 (25.5) 39 204 177

Ø250 3 69 20 277 160 56 -0.05-0.10 332.1 335 325 447 (30) 49 243.5 217.5

Ø300 4 79 20 330 175 67 -0.05-0.10 357 400 390 534 (36.5) 49 263.5 232.5

Dimensions-Center Trunnion (TC), Rod Side Trunnion (TA), Head Side Trunnion (TB)

Ø180, Ø200, Ø250, Ø300





Ø125, Ø140, Ø150, Ø160




KCC Co., Ltd.

www.kccpr.com 891 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Unit : mm

Part no. Bore size ØE F1 F2 KK L ØND

I125 125 46 8 54 M30X1.5 100 25 +0.1 0

I140 140 48 8 54 M30X1.5 105 28 +0.1 0

I150 150, 160 55 8 60 M36X1.5 110 32 +0.1 0

I180 180 70 8 67 M40X1.5 125 40 +0.1 0

I200 200 70 8 67 M45X1.5 125 40 +0.1 0

I250 250 85 8 75.5 M56X2.0 160 50 +0.1 0

I300 300 105 8 84.5 M64X2.0 175 63 +0.1 0

Part no. NX RR U

I125 32 -0.1-0.3 27 33

I140 36 -0.1-0.3 30 39

I150 40 -0.1-0.3 34 39

I180 50 -0.1-0.3 42.5 44

I200 50 -0.1-0.3 42.5 44

I250 63 -0.1-0.3 53 66

I300 80 -0.1-0.3 66 71

Unit : mm

Part no. Bore size ØE F1 F2 KK L ØND

Y125 125 46 8 58 M30X1.5 100 25 +0.1 0

Y140 140 48 8 58 M30X1.5 105 28 +0.1 0

Y150 150, 160 55 8 64 M36X1.5 110 32 +0.1 0

Y180 180 70 8 71 M40X1.5 125 40 +0.1 0

Y200 200 70 8 71 M45X1.5 125 40 +0.1 0

Y250 250 86 9 79 M56X2.0 160 50 +0.1 0

Y300 300 105 9 88 M64X2.0 175 63 +0.1 0

Part no. NX NZ RR U

Y125 32 +0.3+0.1 64 -0.1

-0.3 27 42

Y140 36 +0.3+0.1 72 -0.1

-0.3 30 47

Y150 40 +0.3+0.1 80 -0.1

-0.3 34 46

Y180 50 +0.3+0.1 100 -0.1

-0.3 42.5 54

Y200 50 +0.3+0.1 100 -0.1

-0.3 42.5 54

Y250 63 +0.3+0.1 126 -0.1

-0.3 53 81

Y300 80 +0.3+0.1 160 -0.1

-0.3 66 87

Unit : mm

Part no. Bore size ØD Ød L m t

CJP-12 125 25 -0.06-0.11 23.9 0

-0.21 72 64.3 2.5 1.35

CJP-14 140 28 -0.06-0.11 26.6 0

-0.21 80.6 72.3 2.5 1.65

CJP-15 150, 160 32 -0.08-0.14 30.3 0

-0.25 89.6 80.3 3 1.65

CJP-18 180, 200 40 -0.08-0.14 38 0

-0.25 110.1 100.3 3 1.9

CJP-25 250 50 -0.08-0.11 47 0

-0.25 138.9 126.5 4 2.2

CJP-30 300 63 -0.10-0.17 60 0

-0.3 172.9 160.5 4 2.2

Unit : mm

Part no. Bore size C D H KK T

RN-12 125, 140 53.1 44 46 M30X1.5 18

RN-15 150, 160 63.5 53 55 M36X1.5 21

RN-18 180 69.3 57 60 M40X1.5 23

RN-20 200 80.8 67 70 M45X1.5 27

RN-25 250 98.1 82 85 M56X2.0 34

RN-30 300 110 92 95 M64X2.0 38



Rod End Nut Knuckle Joint Pin/ Clevis Pin



Material: Rolled steel Material: Carbon Steel

Material: FC 40

KCC Co., Ltd.

www.kccpr.com 901 -


Unit : mm

Bore size C ØEB F KK N L PG Rc(PT) S T T TL U W

Ø125 115 75 40 M30X1.5 M14X1.5 98 16 1/2

0.2 X Stroke

133 145 258 (21) 34

Ø140 128 75 40 M30X1.5 M14X1.5 98 16 1/2 133 161 258 (21) 34

Ø150 132 75 40 M36X1.5 M16X1.5 106 17.5 3/4 141 170 277.5 (23) 38

Ø160 144 75 40 M36X1.5 M16X1.5 106 17 3/4 141 184 277.5 (23) 38

Ø180 162 85 45 M40X1.5 M18X1.5 111 17 3/4 153 204 299 (26) 39

Ø200 182 90 45 M45X1.5 M20X1.5 111 16.5 3/4 153 226 299 (30) 39

Ø250 225 105 55 M56X2.0 M24X1.5 141 22 10.17 X Stroke

176 277 358.5 (34) 49

Ø300 270 115 55 M64X2.0 M30X1.5 146 22 1 190 330 387.5 (36.5) 49

For dimensions not shown in these figues, refer to the ACL (Standard) type. SUS band is mounted at bellows at delivery.


Ø180, Ø200, Ø250, Ø300

Ø125, Ø140, Ø150, Ø160

Type J K


Temperature 60 110

KCC Co., Ltd.

www.kccpr.com 911 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Unit : mm

Bore size Effective thread length A B C ØD ØEA ØEB H KK L N PG Rc(PT) SW

Ø125 47 50 15 115 35 59 - 42 M30X1.5 98 M14X1.5 16 1/2 -

Ø140 47 50 15 128 35 59 - 42 M30X1.5 98 M14X1.5 16 1/2 -

Ø150 53 56 17 132 40 59 - 43 M36X1.5 106 M16X1.5 17.5 3/4 -

Ø160 53 56 17 144 40 59 - 43 M36X1.5 106 M16X1.5 17 3/4 -

Ø180 60 63 20 162 45 70 115 48 M40X1.5 111 M18X1.5 17 3/4 17

Ø200 60 63 20 182 50 74 115 48 M45X1.5 111 M20X1.5 16.5 3/4 17

Ø250 67 71 25 225 60 96 140 60 M56X2.0 141 M24X1.5 22 1 20

Ø300 76 80 30 270 70 96 140 60 M64X2.0 146 M30X1.5 22 1 20

Bore size T T TL W

Ø125 145 110 318 34

Ø140 161 110 318 34

Ø150 170 120 346 38

Ø160 184 120 346 38

Ø180 204 135 381 39

Ø200 226 135 381 39

Ø250 277 160 461 49

Ø300 330 175 496 49

Dimensions-Double Rod (ACLW)




Ø180, Ø200, Ø250, Ø300

Ø125, Ø140, Ø150, Ø160

KCC Co., Ltd.

www.kccpr.com 921 -




Ø180, Ø200, Ø250, Ø300

Ø125, Ø140, Ø150, Ø160

Unit : mm

Bore size L TL U

Ø125 197 334 (21)

Ø140 197 334 (21)

Ø150 213 363.5 (23)

Ø160 213 363.5 (23)

Ø180 223 393 (26)

Ø200 223 393 (30)

Ø250 283 484.5 (34)

Ø300 293 519.5 (41.5)


For dimensions not shown in these figues, refer to the ACL (Standard) type.





KCC Co., Ltd.

www.kccpr.com 931 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS




Ø180, Ø200, Ø250, Ø300

Ø125, Ø140, Ø150, Ø160

Unit : mm

Bore size L TL

Ø125 196 416

Ø140 196 416

Ø150 212 452

Ø160 212 452

Ø180 222 492

Ø200 222 492

Ø250 282 602

Ø300 292 642







KCC Co., Ltd.

www.kccpr.com 941 -



Unit : mm

Bore size L TL U

Ø125 196 333 (21)

Ø140 196 333 (21)

Ø150 212 362.5 (23)

Ø160 212 362.5 (23)

Ø180 222 392 (26)

Ø200 222 392 (30)

Ø250 282 483.5 (34)

Ø300 292 518.5 (41.5)


Ø180, Ø200, Ø250, Ø300

Ø125, Ø140, Ø150, Ø160





KCC Co., Ltd.

www.kccpr.com 951 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Unit : mm

Bore size ØB C ØD E ØEB H KK TL

Ø125 60 37 35 39 90 43 M30X1.5 318

Ø140 60 37 35 30 90 43 M30X1.5 318

Ø150 60 46 40 26 90 43 M36X1.5 341

Ø160 60 46 40 26 90 43 M36X1.5 341

Ø180 70 52 45 30 115 48 M40X1.5 376

Ø200 70 52 50 30 115 48 M45X1.5 376

Ø250 86 60 60 35 140 60 M56X2.0 456

Ø300 86 60 70 35 140 60 M64X2.0 496

For dimensions not shown in these figues, refer to the ACL standard type.


Dimensions-Forward Stroke Adjustable (ASJ, BSJ)

Ø180, Ø200, Ø250, Ø300

Ø125, Ø140, Ø150, Ø160

ADJUSTMENTADJUSTMENTADJUSTMENTADJUSTMENT

ADJUSTMENTADJUSTMENTADJUSTMENTADJUSTMENT

Range of adjustment





Bore size Ø125, Ø140, Ø150, Ø160, Ø180, Ø200

Ambient temperature -20 ~ 150

Packing material VITON


Type Lubricated type, Non-Lubricated type

Bore size Ø125, Ø140, Ø150, Ø160, Ø180, Ø200, Ø250, Ø300

Rod material SUS304

Heat Resistant Cylinder (SV) Stainless Steel Piston Rod (SS)

Speci cation Speci cation

KCC Co., Ltd.

www.kccpr.com 961 -


Extra-Large Cylinder

ACX series

ACX series

ACX - TC 400 - S 600

SeriesACX Extra-large cylinder

Cylinder stroke ~ 1000mm

Mounting styleLB Foot FA Rod side ange FB Head side angeCA Single clevisTC Center trunnion

CushionNil Both side cushionN Without cushionR Rod side cuhsionH Head side cushion

Bore size350 ø350400 ø400450 ø450

Rod end attachmentNil NoneI Single knuckle jointY Double knuckle joint

Mounting style

Bore size

Basic mass

LB FA FB TC CA

Additional mass for

each 100mm stroke

Ø350 410 410 410 410 410 24

Ø400 540 540 540 540 540 28

Ø450 679 679 679 679 679 34

Action Double acting

Fluid Air



Min. operating pressure 1.0kgf/cm2 (0.1MPa)Ambient & uid

temperature 5 ~ 60

Operating piston speed 50~500mm/sec


How to Order

Mass

Speci cationsTolerance of stroke

100mm +0.80 251~630mm +1.25

0

101~250mm +1.00 631~1000mm +1.4

0

Max. stroke is 1000mm. Contact us for longer strokes.

Double Acting Single Rod Aluminium Tube Ex) ACX-LB350-S500 Basic mass: 410(Foot Ø350) / Additional mass: 24/100 Cylinder stroke: 500mm 410 + 24/100 X 500 = 530 kg

Calculation:

Bellows

Material Max. Temperature


Symbol


Features

Bore size Ø350 to Ø450 is available.

Excellent durability and performance.

Various mounting styles.


KCC Co., Ltd.

www.kccpr.com 971 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


ACX series



Unit : mm

Bore size A ØD ØEA ØEB ØFD FT FW FX FY FZ KK L N PG

Ø350 90 80 115 175 26 30 110 460 330 510 M72×2.0 200 8-M24×1.5 25

Ø400 100 90 125 196 30 32 120 515 360 575 M82×2.0 225 8-M27×1.5 30

Ø450 110 100 140 215 33 35 120 565 400 630 M90×2.0 240 12-M27×1.5 30

Bore size Rc(PT) T T TL

Ø350 1 225 385 425

Ø400 1 1/4 250 435 475

Ø450 1 1/4 285 485 525

Unit : mm

Bore size A ØD ØEA KK L ØLD LH LS LX LY LT N PG Rc(PT)

Ø350 90 80 115 M72×2.0 200 36 230 410 280 422.5 25 8-M24×1.5 25 1

Ø400 100 90 125 M82×2.0 225 39 295 485 320 512.5 32 8-M27×1.5 30 1 1/4

Ø450 110 100 140 M90×2.0 240 42 320 530 380 562.5 35 12-M27×1.5 30 1 1/4

Bore size T T TL X Y

Ø350 225 385 573 105 43

Ø400 250 435 655 130 50

Ø450 285 485 725 145 55

KCC Co., Ltd.

www.kccpr.com 981 -



ACX series

Unit : mm

Bore size A ØCD CL CX ØD ØEA KK L LR N PG R Rc(PT) T

Ø350 90 63 121 80 80 115 M72×2.0 200 75 8-M24×1.5 25 71 1 225

Ø400 100 71 135 90 90 125 M82×2.0 225 85 8-M27×1.5 30 80 1 1/4 250

Ø450 110 80 150 100 100 140 M90×2.0 240 95 12-M27×1.5 30 90 1 1/4 285

Bore size T TL TZ

Ø350 385 617 546

Ø400 435 690 610

Ø450 485 765 675



Unit : mm

Bore size A ØD ØEA ØEB ØFD FT FW FX FY FZ KK L N PG

Ø350 90 80 115 175 26 30 110 460 330 510 M72×2.0 200 8-M24×1.5 25

Ø400 100 90 125 196 30 32 120 515 360 575 M82×2.0 225 8-M27×1.5 30

Ø450 110 100 140 215 33 35 120 565 400 630 M90×2.0 240 12-M27×1.5 30

Bore size Rc(PT) T T TL

Ø350 1 225 385 425

Ø400 1 1/4 250 435 475

Ø450 1 1/4 285 485 525

KCC Co., Ltd.

www.kccpr.com 991 -


Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

ACX seriesExtra-Large Cylinder

Unit : mm

Bore size A ØD ØEA KK L LZ N PG Rc(PT) RR RT T T ØTD TL TX TY TZ

Ø350 90 80 115 M72×2.0 200 100 8-M24×1.5 25 1 4 85 225 385 71 -0.100 425 490 430 640-0.174

Ø400 100 90 125 M82×2.0 225 112 8-M27×1.5 30 1 1/4 4 90 250 435 80 -0.100 475 540 490 720-0.174

Ø450 110 100 140 M90×2.0 240 117 12-M27×1.5 30 1 1/4 4 100 285 485 90 -0.120 525 610 530 800-0.207

Dimensions-Center Trunnion (TC)

Unit : mm

Bore size CF

CT

F J KK L ND NX RA

USingle

knuckle joint

Double knuckle

joint

Single knuckle

joint

Double knuckle

jointØ350 142 110 160 92 30 M72×2.0 205 63 80 276 85 90

Ø400 160 120 180 102 30 M82×2.0 215 71 90 295 90 100

Ø450 180 130 200 112 40 M90×2.0 225 80 100 315 95 120

Unit : mm

Bore size Stroke S A ØEB

Ø350

0-250 186

90 190251-400 216401-630 276

631-1000 356

Ø400

0-250 205

100 220251-400 245401-630 295

631-1000 385

Ø450

0-250 204

110 230251-400 234401-630 294

631-1000 374

Dimensions-Bellows Attached (J) Dimensions-Accessory

Single Knuckle Joint Double Knuckle JointBellows Attached Type (J)

SUS band is mounted at bellows at delivery.

Type J K


Heat resistant 60 110

KCC Co., Ltd.

www.kccpr.com 1001 -


Low Friction Cylinder

KLC series

KLC CA - 50 SM - 64

SeriesKLC Low friction cylinder

ActionSM Single actingWM Double acting

Mounting styleCA Single clevis


Ø50 64Ø63 78

Bore size50 ø5063 ø63

Speci cations

KLC series

How to Order

KLC CA-50 SM-64

Symbol


Single Acting /Single Rod

Features

Low friction cylinder.

Bore size: ø50, ø63.

Single clevis mounting style.

Smooth slow movement is possible.

Action Single/Double acting, Single rod

Fluid Clean Air (for 5 Filter & Oil remove filter)



Ambiet & uid temperature 5 ~ 60

Standard stroke Refer to the standard stroke table above

Internal leakage 1.6 /min

Mounting direction Horizontal

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

KLC seriesLow Friction Cylinder

Unit : mm

Bore size A H T L L1 CT CL ØCD CX C T KK Rc(PT)

Ø50 20 11 45 133 221 8 33 10 16 50 64 M10X1.25 1/4

Ø63 24 10 50 160 260 8 38 12 18 60 80 M12X1.25 1/4

Dimensions

KCC Co., Ltd.



Labyrinth Cylinder

KLCS series

Speci cations

KLCS series

How to Order

KLCS CA 50 - 64

SeriesLCS Labyrinth cylinder

Cylinder strokeBore size Ø20 Ø30 Ø40 Ø50 Ø63 Ø80 Ø100Standard

stroke 50 50 50 64 78 108 144

Mounting styleCA Single clevisCB Double clevis

Bore size20 30 40 50 63 80 100

Ø20 Ø30 Ø40 Ø50 Ø63 Ø80 Ø100

KLCS CA 50-64

Symbol

Single Acting / Single Rod

Features

Seal is not applied this ensures smooth

and sensitive movement to minor load variation.

Due to the high ef ciency, almost 100% of the

supply pressure is used as driving force. It is

also applicable with low pressure.

Application

Film winder tension control. Control the tension of textile machinery. To maintain balance of electric servo mechanism.

Action Single acting

Fluid Clean air (for 5 Filter & Oil remove filter)

Max. stroke 300mm

Min. operating pressure 0.02 ~ 0.4kgf/cm2 (0.002 ~ 0.04MPa)

Ambiet & uid temperature -10 ~ 40 (Contact KCC for higher temperature type)

Lubrication Not required (Do not lubricate)

Standard stroke Refer to the standard stroke table above

Internal leakage 300 /min (ANR) (for Ø50 cylinder at 0.4kgf/cm2)

Attachment direction Vertical (within 15° from vertical axis)

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

KLCS seriesLabyrinth Cylinder

Unit : mm

Bore size A B C D E F G H J K L M N P Q R

Ø20 20 5 25 M10X1.25 0 11 21 22 8 12 0 0 38 Rc(PT) 1/8 89 135

Ø30 20 5 25 M10X1.25 0 13 25 26 10 14 0 0 48 Rc(PT) 1/8 124 174

Ø40 20 5 25 M10X1.25 0 14 27 30 10 16 0 0 59 Rc(PT) 1/8 136 188

Ø50 20 6 26 M10X1.25 9 33 47 30 10 16 60 7 78 Rc(PT) 1/4 144 217

Ø63 20 7 30 M10X1.25 10 38 54 35 12 18 70 9 90 Rc(PT) 1/4 143 227

Ø80 23 8 40 M10X1.25 12 44 64 40 15 22 80 9 100 Rc(PT) 1/4 115 219

Ø100 40 8 48 M10X1.25 14 50 68 56 18 26 100 12.5 120 Rc(PT) 1/4 150 266

Dimensions

KCC Co., Ltd.



Compact Cylinder

AF/ADF series

AF/ADF series

How to Order

AF - 20 A - S 15

Series

AF Single rod compact cylinder (Without auto switch)

AFW Double rod compact cylinder(Without auto switch)

ADF Single rod compact cylinder(With auto switch)

ADFW Double rod compact cylinder(With auto switch)

CushionNil NoneC Rubber bumperA Air cushion

Custom made type. (Under developement)

Special OrderNil None

TS Multi-step stroke cylinder (Single rod)

TW Multi-step stroke cylinder (Double rod)

ASJ Stroke adjustable type (in forward direction within 10mm)



SV Heat resistant cylinderE Anti-lateral load cylinder

MS Scraper cylinder (Ø32 ~ Ø80)SV Heat resistant cylinderSS Stainless steel piston rod

Number of auto switchesNil 2 pcs1 1 pcN N pcs (N:3,4,5...)


Hole typeA Both end tapped type (Standard)B Through hole type

For Ø12 & Ø16 type, through hole type(B) is standard type.

Type

Nil Single rod, Non-lubricated (Standard)

L Low hydraulic pressure

Rod end threadNil Female thread N Male thread

Mounting styleNil StandardLB FootFA Rod side ange FB Head side angeCB Double clevis

Some of the dimensions of bracket attached type is different with standard type.

Bore size12 Ø12 50 Ø5016 Ø16 63 Ø6320 Ø20 80 Ø8025 Ø25 100 Ø10032 Ø32 125 Ø12532 Ø32 125 Ø12540 Ø40

Symbol





Features

Ideal for clamping, press-in and under short stroke condition. Can be installed even in a narrow space

with a shorter length in axial thrust direction. Easy installation only with bolts. Excellent appearance after anodizing.

Cylinder strokeAction

Bore sizeStandard stroke

Single rod Double rodØ12

5, 10, 15. 20. 25, 30 5, 10, 15. 20. 25, 30Ø16Ø20

5, 10, 15, 20, 25, 30, 35, 40, 45, 50 5, 10, 15, 20, 25, 30, 35, 40, 45, 50Ø25Ø32 5, 10, 15, 20, 25, 30, 35, 40, 45, 50,

75, 100 5, 10, 15, 20, 25, 30, 35, 40, 45, 50Ø40Ø50

5, 10, 15, 20, 25, 30, 35, 40, 45, 50, 75, 100 5, 10, 15, 20, 25, 30, 35, 40, 45, 50

Ø63Ø80

Ø100Ø125

Refer to page [1]-117, for dimensions of long stroke type (cylinder above standard stroke)

Auto switch

Reed A/S Model Solid state A/S Model

A-72 D-A72K F-7NV D-F7NVKA-73 D-A73K F-7PV D-F7PVKA-80 D-A80K F-7BV D-F7BVKA-90 D-A90(V)K F-9N(V) D-F9N(V)KA-93 D-A93(V)K F-9P(V) D-F9P(V)KA-96 D-A96(V)K F-9B(V) D-F9B(V)K

Only for auto switch attached type. Refer to Auto Switch Catalogue for more

information.


KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Compact Cylinder

AF/ADF series

Min. Operating Pressure

Bore size Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100 Ø125

Double acting 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5

Single acting (Spring return, Spring extend) 1.5 1.5 1.8 1.8 1.7 1.5 1.3 - - - -

Min. Stroke For Auto Switch Attachment

Number of auto switch Min. stroke

1 pc 5mm

2 pcs 10mm

Only for ADF series(auto switch attached type).

Bore sizeMounting Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100

Foot LB(CP)12 LB(CP)16 LB(CP)20 LB(CP)25 LB(CP)32 LB(CP)40 LB(CP)50 LB(CP)63 LB(CP)80 LB(CP)100

Flange FA/FB(CP)12 FA/FB(CP)16 FA/FB(CP)20 FA/FB(CP)25 FA/FB(CP)32 FA/FB(CP)40 FA/FB(CP)50 FA/FB(CP)63 FA/FB(CP)80 FA/FB(CP)100Double clevis

(with pin) CB(CP)12 CB(CP)16 CB(CP)20 CB(CP)25 CB(CP)32 CB(CP)40 CB(CP)50 CB(CP)63 CB(CP)80 CB(CP)100

For foot mounting, set (2 pcs) are basic.

Accessory

Mounting Style

Type Double acting single rod

Accessory Standard Foot Rod side ange

Head side ange

Double clevis

Standard Rod end nut

Clevis pin - - - -

OptionSingle knuckle joint


For double clevis and double knuckle joint, pin and snap ring are included. Every mounting bracket includes a hex-wrench bolt. Rod end nut is only applicable to male thread type.

Bore size(mm)Rod end attachment Ø12 Ø16 Ø20 Ø25 Ø32,Ø40 Ø50,Ø63 Ø80 Ø100

Single knuckle joint I(CP)12 I(CP)16 I(CP)20 I(CP)25 I(CP)32,40 I(CP)50,63 I(CP)80 I(CP)100

Double knuckle joint Y(CP)12 Y(CP)16 Y(CP)20 Y(CP)25 Y(CP)32,40 Y(CP)50,63 Y(CP)80 Y(CP)100

Rod end nut RN(CP)12 RN(CP)16 RN(CP)20 RN(CP)25 RN(CP)32,40 RN(CP)50,63 RN(CP)80 RN(CP)100

Rod End Attachment

Speci cationsFluid Air



Ambient & uid temperature -10 ~ 70 (No Freezing)


Cushion None(Standard), Rubber bumper, Air cushion



Rod end thread Female thread, Male thread

For intermediate strokes 55~100, spacer of 5, 10, 20 mm will be used. Example: AF50B-S55 is produced by installing 20mm spacer in AF50B-S75.

Low hydraulic pressure type and standard type have the same dimensions.

KCC Co., Ltd.



AF/ADF seriesCompact Cylinder

Auto Switch Attachment

Auto switch mounting screw

Auto switch spacer

Auto switch mounting nut

(M3x0.5x1.0 )

Adjusting screw

Auto switch

Unit : mm

Bore size A B

Ø12 7.5 3

Ø16 7.5 3

Ø20 8 6.5

Ø25 8 6.5

Ø32 9.5 7

Ø40 13.5 9.5

Ø50 13.5 12.5

Ø63 14 15.5

Ø80 17 20

Ø100 21.5 25

Ø125 32.5 32.5

Ø12~Ø25 Ø12~Ø125 (Standard)

Ø20~Ø125

For 5mm stroke cylinder(with 1 auto switch) or 10mm stroke cylinder (with 2 auto switches) when auto switch/auto switches do not turn off or both switches turn on simultaneously, mount the auto switch 1~2mm more toward.

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Unit : g

Cylinder stroke

Bore size

Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100

5 43 64 94 134 182 269 - - - -

10 49 71 106 149 202 290 455 627 1162 1966

15 55 79 118 164 222 312 488 665 1222 2047

20 61 87 131 180 241 333 521 703 1282 2127

25 67 95 143 195 261 355 554 741 1342 2208

30 73 102 155 210 281 376 587 779 1403 2288

35 - - 167 226 300 398 620 817 1463 2368

40 - - 179 241 320 420 653 855 1524 2449

45 - - 191 256 340 441 686 893 1584 2529

50 - - 203 272 359 463 719 931 1644 2610

75 - - - - 459 575 891 1129 1941 3018

100 - - - - 558 687 1062 1326 2237 3426

Unit : g

Cylinder stroke

Bore size

Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100

5 50 77 120 170 238 353 - - - -

10 58 87 136 185 260 383 609 798 1393 2334

15 65 96 151 201 283 412 645 840 1469 2443

20 73 106 166 216 306 442 681 882 1546 2551

25 80 115 182 232 329 471 716 924 1622 2660

30 87 125 197 247 352 500 752 966 1699 2769

35 - - 212 263 375 530 788 1008 1775 2877

40 - - 228 279 398 559 823 1051 1851 2986

45 - - 243 294 421 589 859 1093 1928 3094

50 - - 258 310 444 618 895 1135 2004 3203

75 - - - - 558 765 1073 1346 2387 3746

100 - - - - 673 912 1252 1556 2769 4289

Both end tapped 2 2 6 6 6 6 6 19 45 45

Rod end male

thread

Male thread part

1.5 3 6 12 26 27 53 53 120 175

Nut 1 2 4 8 17 17 32 32 49 116Rubber bumper attached

0 0 -2 -3 -3 -7 -9 -18 -31 -56

Foot 55 67 164 186 142 154 243 317 683 1052Rod side

ange 57 69 139 161 180 214 373 559 1056 1365

Head side ange 54 65 133 152 165 198 348 534 1017 1309

Double clevis 32 39 88 123 151 196 393 554 1109 1887

For foot, rod side flange, and head side flange mounting, bolt is included. Double clevis includes a pin, a snap ring and bolt.

Both end tapped 2 2 6 6 6 6 6 19 45 45

Rod end male

thread

Male thread part

3 6 12 24 52 54 106 106 240 350

Nut 2 4 8 16 34 34 64 64 98 232Rubber bumper attached

0 0 -2 -2 -3 -7 -12 -20 -34 -57

Mounting bolt is included for foot, head side flange type.


MassADF Series

ADFW Seires

Unit : g

Cylinder stroke

Bore size

Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100

5 29 42 63 86 125 187 - - - -

10 35 50 75 100 145 208 339 480 916 1608

15 41 59 88 115 165 230 372 518 976 1688

20 47 67 101 129 184 251 405 556 1036 1768

25 54 76 114 144 204 273 438 594 1097 1849

30 60 84 127 158 224 294 471 632 1157 1929

35 - - 140 173 244 315 504 670 1217 2010

40 - - 152 187 263 337 537 708 127 2090

45 - - 165 202 283 358 570 748 1338 2170

50 - - 178 216 303 380 603 784 1398 2251

75 - - - - 448 552 872 1112 1917 2982

100 - - - - 547 664 1043 1308 2215 3391

Unit : g

Cylinder stroke

Bore size

Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100

5 42 59 89 119 185 279 - - - -

10 49 68 104 136 212 308 497 646 1149 1960

15 56 77 119 153 235 337 538 682 1225 2068

20 63 86 134 170 257 367 580 718 1302 2177

25 70 95 149 187 280 396 622 754 1378 2286

30 77 104 164 204 303 426 664 790 1455 2394

35 - - 179 221 326 455 705 826 1531 2503

40 - - 194 238 349 484 747 862 1608 2612

45 - - 209 255 372 514 789 899 1684 2720

50 - - 224 272 395 543 830 935 1760 2829

75 - - - - 555 749 1122 1187 2296 3589

100 - - - - 670 896 1331 1368 2678 4132

AF Series

AFW Series

1. AF Ex) AF-CB32A-S20NC

Basic mass: 184 / Both end tapped type: 6 / Rod end male thread: 43 Rubber bumper: -3 / Double clevis: 151 184 + 6 + 43 - 3 + 151 = 381g

1. AFW Ex) AFW-CB32A-S20NC


2. ADF Ex) ADF-CB32A-S20NC


2. ADFW Ex) ADFW-CB32A-S20NC


Calculation:

Calculation:

KCC Co., Ltd.


PNEUMATIC & HYDRAULIC AF/ADF seriesCompact Cylinder

Structure


Ø12 Ø16 Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø100 Ø125

11 Piston Packing NBR OPA12 OPA16 OPA20 OPA25 OPA32 OPA40 OPA50 OPA63 OPA80 OPA100 OPA125

12 Rod Packing NBR DYR6K DYR8K DYR10K DYR12K DYR16K DRP16 DRP20 DRP20 DRP25 DRP30 DRP35

13 Tube O-Ring NBR S-10 S-14 S-18 S-22 S-29 S-37 S-46 S-60 S-75 S-95 S-120

Part #9, #10 are only for rubber bumper attached cylinder.

Only for AF series

For both AF/ADF series. For both AF/ADF series

Only for AF series


1 Cylinder Tube AL Alloy Hard Anodized Aluminium

2 Piston AL Alloy -

3 Piston RodStainless Steel:ø12~Ø25

Hard Chromium PlatingCarbon Steel:ø32~Ø125

4 Rod CoverBrass:ø12~Ø32

White AnodizingAl Ø40~Ø125


6 Snap Ring Spring Steel -

7 Bush Copper -

8 Magnet - Only for Auto Switch Attached type

9 Cushion Damper A Urethane -

10 Cushion Damper B Urethane -

Single Acting Spring Return Single Acting Spring Extend

Single Rod, Double Acting Double Rod, Double Acting

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Structure-Air Cushion Type

With auto switch

With auto switch

Details of A part


1 Cylinder Tube AL Alloy Hard Anodized

2 Piston AL Alloy Chromated

3 Piston RodStainless Steel Ø20, Ø25

Carbon Steel Ø32~Ø100, Hard Chrome Plated

4 CollarAL Alloy Ø20~Ø40, Anodized

AL Alloy Casted Ø50~Ø100, Chromated, Painted

5 Retaining Ring Carbon Tool Steel Phosphate coating

6 Bush Bearing Alloy Ø50~Ø100

7 Wear Ring Resin Ø63~Ø100

8 Rod End Nut Carbon Steel -


9 Magnet - -

10 Steel BallHigh Carbon

Chrome Bearing Steel

-

11 Check Seal Retainer Brass Electroless Nickel Plated

12 Cushion Needle Stainless Steel

13 Check Seal NBR -

14 Check Gasket NBR -

15 Needle Gasket NBR -

Ø50 ~ Ø100

Ø20 ~ Ø40


11

A part

A part

Rod end male thread


Ø20 Ø25 Ø32 Ø40 Ø50 Ø63 Ø80 Ø10016 Piston Seal NBR OPA20 OPA25 OPA32 OPA40 OPA50 OPA63 OPA80 OPA100

17 Rod Seal NBR DYR10K DYR12K DYR16K DRP16 DRP20 DRP20 DRP25 DRP30

18 Tube Gasket NBR S18 S22 S29 S37 S46 S60 S75 S95

KCC Co., Ltd.



Compact Cylinder

AF/ADF series

Mounting Bolt (Through Hole)

Model C L Set Bolt AF12B - S 5

6.5

25 M3 X 25 l - S 10 30 X 30 l - S 15 35 X 35 l - S 20 40 X 40 l - S 25 45 X 45 l - S 30 50 X 50 l AF16B - S 5

6.5

25 M3 X 25 l - S 10 30 X 30 l - S 15 35 X 35 l - S 20 40 X 40 l - S 25 45 X 45 l - S 30 50 X 50 lAF20B - S 5

7.5

25 M5 X 25 l - S 10 30 X 30 l - S 15 35 X 35 l - S 20 40 X 40 l - S 25 45 X 45 l - S 30 50 X 50 l - S 35 55 X 55 l - S 40 60 X 60 l - S 45 65 X 65 l - S 50 70 X 70 l

AF25B - S 5

9.5


AF32B - S 5

9

30 M5 X 30 l - S 10 35 X 35 l - S 15 40 X 40 l - S 20 45 X 45 l - S 25 50 X 50 l - S 30 55 X 55 l - S 35 60 X 60 l - S 40 65 X 65 l - S 45 70 X 70 l - S 50 75 X 75 l - S 75 110 X 110 l

- S 100 135 X 135 lAF40B - S 5

7.5

35 M5 X 35 l - S 10 40 X 40 l - S 15 45 X 45 l - S 20 50 X 50 l - S 25 55 X 55 l - S 30 60 X 60 l - S 35 65 X 65 l - S 40 70 X 70 l - S 45 75 X 75 l - S 50 80 X 80 l - S 75 115 X 115 l

- S 100 140 X 140 l

Model C L Set Bolt AF50B - S 10

12.5


- S 100 145 X 145 l AF63B - S 10

14.5


- S 100 150 X 150 l AF80B - S 10

15


- S 100 155 X 155 l AF100B - S 10

15.5


- S 100 165 X 165 l AF125B - S 10

22.9


- S 100 190 X 190 l

(Note) Mounting bolt of ADF 1) ADF series body length is 10mm longer than that of AF series. Thus, ADF series required a 10mm longer mounting bolt than that of AF series. Ex) AF 40B - S20 M5X50L ADF 40B - S20 M5X60L

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Dimensions-Standard Ø12, Ø16, Ø20, Ø25

Unit : mm

Bore sizeWithout magnet (AF) With magnet (ADF)

A B C ØD ØE F FNL PA TL L PA TL

Ø12 17 7.5 20.5 28 10 31.5 10.5 25 15.5 6 32 6 9

Ø16 18.5 8 22 30.5 10 34 12 29 20 8 38 8 10

Ø20 19.5 10.5 24 31.5 10.5 36 14 36 25.5 10 47 8 12

Ø25 22.5 11 27.5 32.5 11 37.5 17.5 40 28 12 52 12 15

Bore size K KK NKK ØO PB ØQ Rc(PT) T TN

Ø12 5 M3X0.5 M5X0.8 3.5 5 6.5 Depth 3.5 M5X0.8 3.5 14

Ø16 6 M4X0.7 M6X1.0 3.5 5.5 6.5 Depth 3.5 M5X0.8 3.5 15.5

Ø20 8 M5X0.8 M8X1.25 5.5 6 9 Depth 7 M5X0.8 4.5 18.5

Ø25 10 M6X1.0 M10X1.25 5.5 5.5 9 Depth 7 M5X0.8 5 22.5

Both End Tapped (Standard)

Unit : mm

Bore size G Q1 ØQ2 R

Ø12 3.5 M4X0.7 6.5 7

Ø16 3.5 M4X0.7 6.5 7

Ø20 7 M6X1.0 9 10

Ø25 7 M6X1.0 9 10

Rod End-Female Thread (Standard)

Rod End-Male Thread

Ø12

Ø12

Ø20 ~ Ø25

Ø20 ~ Ø25

Ø16

Ø16

1

2

KCC Co., Ltd.




Dimensions-Standard Ø32~Ø125

Unit : mm

Bore size StrokeWithout

magnet (AF)With magnet

(ADF) A B C ØD ØE F FN K KK NKK ØO PA PB ØQL TL L TL

Ø325

23 30 33 40 23.5 45 34 16 60 13 20.5 14 M8X1.25 M14X1.5 5.511.5 5.5

9 Depth 710~100 10.5 7.5

Ø40 5~100 29.5 36.5 39.5 46.5 23.5 52 40 16 69 13 20.5 14 M8X1.25 M14X1.5 5.5 12 8.5 9 Depth 7

Ø50 5~100 30.5 38.5 40.5 48.5 28.5 64 50 20 86 15 26 18 M10X1.5 M18X1.5 6.8 10.5 10.5 11 Depth 8

Ø63 5~100 36 44 46 54 28.5 77 60 20 103 15 26 18 M10X1.5 M18X1.5 9 15 11 14 Depth 10.5

Ø80 5~100 43.5 53.5 53.5 63.5 35.5 98 77 25 132 21 32.5 22 M16X2.0 M22X1.5 11 18 12.5 17.5 Depth 13.5

Ø100 5~100 53 65 63 75 35.5 117 94 30 156 27 32.5 27 M20X2.5 M26X1.5 11 23 13 17.5 Depth 13.5

Ø125 10~300 83 99 83 75 45 142 114 35 190 30 42 30 M22X2.5 M30X1.5 12.5 24.5 24.5 21.2 Depth 18.4

Bore size Rc(PT) T TN U W Z

Ø32M5X0.8 (5st)

7 28.5 4.5 49.5 14Rc(PT)1/8

Ø40 Rc(PT)1/8 7 28.5 5 57 14

Ø50 Rc(PT)1/4 8 33.5 7 71 18

Ø63 Rc(PT)1/4 8 33.5 7 84 18

Ø80 Rc(PT)3/8 10 43.5 6 104 22

Ø100 Rc(PT)3/8 12 43.5 6.5 123.5 22

Ø125 Rc(PT)3/8 16 58 11 162 32

Depth F

Through holeThrough hole

Through hole


Rod End-Male Thread

Ø32 ~ Ø125

Ø32 ~ Ø125

1

2

Unit : mm


Ø32 7 M6X1.0 9 10

Ø40 7 M6X1.0 9 10

Ø50 8 M8X1.25 11 14

Ø63 10.5 M10X1.50 14 18

Ø80 13.5 M12X1.75 17.5 22

Ø100 13.5 M12X1.75 17.5 22

Ø125 18.4 M14X2.0 21.2 25

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS



Unit : mm

Bore size StrokeWithout magnet

(AF)With magnet

(ADF) A ØD FN LD LG LH LT LX LY LZ KK NKK T TN X YTL L LS TL L LS

Ø325~50 47.2 23 7

57.2 33 17 23.5 16 20.5 6.6 4 30 3.2 58 57 71 M8X1.25 M14X1.5 17 38.5 11.2 5.875,100 57.2 33 17

Ø405~50 53.7 29.5 13.5

63.7 39.5 23.5 23.5 16 20.5 6.6 4 33 3.2 64 64 78 M8X1.25 M14X1.5 17 38.5 11.2 775,100 63.7 39.5 23.5

Ø5010~50 56.7 30.5 7.5

66.7 40.5 17.5 28.5 20 26 9 5 39 3.2 79 78 95 M10X1.5 M18X1.5 18 43.5 14.7 875,100 66.7 40.5 17.5

Ø6310~50 62.2 36 10

72.2 46 20 28.5 20 26 11 5 46 3.2 95 91.5 113 M10X1.5 M18X1.5 18 43.5 16.2 975,100 72.2 46 20

Ø8010~50 75 43.5 13.5

85 53.5 23.5 35.5 25 32.5 13 7 59 4.5 118 114 140 M16X2.0 M22X1.5 20 53.5 19.5 1175,100 85 53.5 23.5

Ø10010~50 88 53 19

98 63 29 35.5 30 32.5 13 7 71 6 137 136 162 M20X2.5 M26X1.5 22 53.5 23 12.575,100 98 63 29

Bore size : Ø32, Ø40, Ø50, Ø63, Ø80, Ø100

Rod End Male Thread

Unit : mm

Bore sizeWithout magnet

(AF)With magnet

(ADF) A ØD FN LD LG LH LT LX LY LZ KK NKK T TN X YTL L LS TL L LS

Ø12 35.3 17 5 46.3 28 16 10.5 6 9 4.5 2.8 17 2 34 29.5 44 M3X0.5 M5X0.8 13.5 24 8 4.5

Ø16 36.8 18.5 6.5 48.8 30.5 18.5 12 8 10 4.5 2.8 19 2 38 33.5 48 M4X0.7 M6X1.0 13.5 25.5 8 5

Ø20 41.2 19.5 7.5 53.2 31.5 19.5 14 10 12 6.6 4 24 3.2 48 42 62 M5X0.8 M8X1.25 14.5 28.5 9.2 5.8

Ø25 44.7 22.5 7.5 54.7 32.5 17.5 17.5 12 15 6.6 4 26 3.2 52 46 66 M6X1.0 M10X1.25 15 32.5 10.7 5.8

Bore size : Ø12, Ø16, Ø20, Ø25

Rod End Male Thread

KCC Co., Ltd.



Rod End Male Thread

Rod End Male Thread



Unit : mm


(AF)With magnet

(ADF) A ØD FD FN FQ FT FX FZ KK NKK T TNTL L TL L

Ø12 30.5 17 41.5 28 10.5 6 4.5 9 25 5.5 45 55 M3X0.5 M5X0.8 13.5 24

Ø16 32 18.5 44 30.5 12 8 4.5 10 30 5.5 45 55 M4X0.7 M6X1.0 13.5 25.5

Ø20 34 19.5 46 31.5 14 10 6.6 12 39 8 48 60 M5X0.8 M8X1.25 14.5 28.5

Ø25 37.5 22.5 47.5 32.5 17.5 12 6.6 15 42 8 52 64 M6X1.0 M10X1.25 15 32.5

Unit : mm



(ADF) A ØD FD FN FQ FT FX FY FZ KK NKK T TNTL L TL L

Ø325~50 40 23

50 33 23.5 16 5.5 20.5 48 8 56 34 65 M8X1.25 M14X1.5 17 38.575,100 50 33

Ø405~50 46.5 29.5

56.5 39.5 23.5 16 5.5 20.5 54 8 62 40 72 M8X1.25 M14X1.5 17 38.575,100 56.5 39.5

Ø5010~50 48.5 30.5

58.5 40.5 28.5 20 6.6 26 67 9 76 50 89 M10X1.5 M18X1.5 18 43.575,100 58.5 40.5

Ø6310~50 54 36

64 46 28.5 20 9 26 80 9 92 60 108 M10X1.5 M18X1.5 18 43.575,100 64 46

Ø8010~50 63.5 43.5

73.5 53.5 35.5 25 11 32.5 99 11 116 77 134 M16X2.0 M22X1.5 20 53.575,100 73.5 53.5

Ø10010~50 75 53

85 63 35.5 30 11 32.5 117 11 136 94 154 M20X2.5 M26X1.5 20 53.575,100 85 63

Bore size : Ø32, Ø40, Ø50, Ø63, Ø80, Ø100


KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS



Unit : mm


(AF)With magnet

(ADF) A ØD FD FN FT FV FX FZ KK NKK T TNTL L TL L

Ø12 26 17 37 28 10.5 6 4.5 9 5.5 25 45 55 M3X0.5 M5X0.8 3.5 14

Ø16 27.5 18.5 39.5 30.5 12 8 4.5 10 5.5 30 45 55 M4X0.7 M6X1.0 3.5 15.5

Ø20 32 19.5 44 31.5 14 10 6.6 12 8 39 48 60 M5X0.8 M8X1.25 4.5 18.5

Ø25 35.5 22.5 45.5 32.5 17.5 12 6.6 15 8 42 52 64 M6X1.0 M10X1.25 5 22.5

Bore size : Ø32, Ø40, Ø50, Ø63, Ø80, Ø100


Unit : mm



(ADF) A ØD FD FN FQ FT FX FY FZ KK NKK T TNTL L TL L

Ø325~50 40 23

50 33 23.5 16 5.5 20.5 48 8 56 34 65 M8X1.25 M14X1.5 17 38.575,100 50 33

Ø405~50 46.5 29.5

56.5 39.5 23.5 16 5.5 20.5 54 8 62 40 72 M8X1.25 M14X1.5 17 38.575,100 56.5 39.5

Ø5010~50 48.5 30.5

58.5 40.5 28.5 20 6.6 26 67 9 76 50 89 M10X1.5 M18X1.5 18 43.575,100 58.5 40.5

Ø6310~50 54 36

64 46 28.5 20 9 26 80 9 92 60 108 M10X1.5 M18X1.5 18 43.575,100 64 46

Ø8010~50 63.5 43.5

73.5 53.5 35.5 25 11 32.5 99 11 116 77 134 M16X2.0 M22X1.5 20 53.575,100 73.5 53.5

Ø10010~50 75 53

85 63 35.5 30 11 32.5 117 11 136 94 154 M20X2.5 M26X1.5 20 53.575,100 85 63

Rod End Male Thread

Rod End Male Thread

KCC Co., Ltd.



Unit : mm

Bore size StrokeWithout magnet

(AF)With magnet

(ADF) A CD CL CT CV CX CZ ØD FN KK N NKK R T TNTL L TZ TL L TZ

Ø325~50 60 23 50

70 33 60 23.5 10 20 5 14 18 36 16 20.5 M8X1.25 M6XP1.0 M14X1.5 10 7 28.575,100 70 33 60

Ø405~50 68.5 29.5 58.5

78.5 39.5 68.5 23.5 10 22 6 14 18 36 16 20.5 M8X1.25 M6XP1.0 M14X1.5 10 7 28.575,100 78.5 39.5 68.5

Ø5010~50 80.5 30.5 66.5

90.5 40.5 76.5 28.5 14 28 7 20 22 44 20 26 M10X1.5 M8XP1.25 M18X1.5 14 8 33.575,100 90.5 40.5 76.5

Ø6310~50 88 36

84 98 46 84 28.5 14 30 8 20 22 44 20 26 M10X1.5 M10XP1.5 M18X1.5 14 8 33.575,100 98 46

Ø8010~50 109.5 43.5

101.5 119.5 53.5 101.5 35.5 18 38 10 27 28 56 25 32.5 M16X2.0 M12XP1.75 M22X1.5 18 10 43.575,100 119.5 53.5

Ø10010~50 132 53

120 142 63 120 35.5 22 45 13 31 32 64 30 32.5 M20X2.5 M12XP1.75 M26X1.5 22 12 43.575,100 142 63

Unit : mm


(AF)With magnet

(ADF) A ØD FN CB CD CL CT CV CX CZ KK N NKK R T TNTL L TZ TL L TZ

Ø12 40.5 17 34.5 51.5 28 45.5 10.5 6 9 12 5 14 4 7 5 10 M3X0.5 M4XP0.7 M5X0.8 6 3.5 14

Ø16 43 18.5 37 55 30.5 49 12 8 10 14 5 15 4 10 6.5 12 M4X0.7 M4XP0.7 M6X1.0 6 3.5 15.5

Ø20 51 19.5 42 63 31.5 54 14 10 12 20 8 18 5 12 8 16 M5X0.8 M6XP1.0 M8X1.25 9 4.5 18.5

Ø25 57.5 22.5 47.5 67.5 32.5 57.5 17.5 12 15 24 10 20 5 14 10 20 M6X1.0 M6XP1.0 M10X1.25 10 5 22.5



Bore size : Ø32, Ø40, Ø50, Ø63, Ø80, Ø100


Rod End Male Thread

Rod End Male Thread

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

NKKNKK

øD

TLTL + STROKE + STROKE

L + STROKE + STROKET

2-Cushion needle2-Cushion needle2-M5x0.8 2-M5x0.8 (Port size)(Port size)

FNFN

A

TNTN

H G

Dimensions-With Air Cushion

Unit : mm

Bore size A B C ØD ØE F G H FN K KK L NKK ØO ØQ T TL TN

Ø20 14 36 25.5 10 47 8 15.5 21 12 8 M5X0.8 32 M8X1.25 5.5 9 Depth 7 4.5 36.5 18.5

Ø25 17.5 40 28 12 52 12 17 23 15 10 M6X1.0 36.5 M10X1.25 5.5 9 Depth 7 5 41.5 22.5

Unit : mm

Bore size A B C ØD ØE F FN G H K KK L NKK ØO ØQ Rc(PT) T TL TN U W Z

Ø32 23.5 45 34 16 60 13 20.5 18.5 23 14 M8X1.25 37 M14X1.5 5.5 9 Depth 7 1/8 7 44 28.5 4.5 49.5 14

Ø40 23.5 52 40 16 69 13 20.5 20 28 14 M8X1.25 44 M14X1.5 5.5 9 Depth 7 1/8 7 51 28.5 5 57 14

Ø50 28.5 64 50 20 86 15 26 28.5 31.5 18 M10X1.5 49.5 M18X1.5 6.8 11 Depth 8 1/4 8 57.5 33.5 7 71 18

Ø63 28.5 77 60 20 103 15 26 31 34 18 M10X1.5 55 M18X1.5 9 14 Depth 10.5 1/4 8 63 33.5 7 84 18

Ø80 35.5 98 77 25 132 21 32.5 35.5 39 22 M16X2.0 63.5 M22X1.5 11 17.5 Depth 13.5 3/8 10 73.5 43.5 6 104 22

Ø100 35.5 117 94 30 156 27 32.5 40 43 27 M20X2.5 76 M26X1.5 11 17.5 Depth 13.5 3/8 12 88 43.5 6.5 123.5 22

Bore size : Ø20, Ø25

Rod End Male Thread

øD

T L + STROKE + STROKE

TLTL + STROKE + STROKE

2-Cushion2-Cushion needle needle

(Port size)(Port size)2-2- Rc(PT)Rc(PT)

Z

U

W

øE

K

FNFN

A

TNTN

NKKNKK

KK Depth FKK Depth F

GH

4-ØO Through hole4-ØO Through hole8-ØQ C.B8-ØQ C.B

Bore size : Ø32, Ø40, Ø50, Ø63, Ø80, Ø100

Rod End Male Thread


KCC Co., Ltd.



Dimensions-Long Stroke Cylinder (AF, ADF)

Unit : mm

Bore size Stroke A ØD ØEB FN L KK NKK PA PB T TL TN

Ø12 35~100 10.5 6 - 9 35 M3X0.5 M5X0.8 10 10 13.5 59 24

Ø16 35~100 12 8 - 10 38 M4X0.7 M6X1.0 10 10 13.5 63.5 25.5

Ø20 75~200 14 10 - 12 41 M5X0.8 M8X1.25 10.5 10.5 14.5 69.5 28.5

Ø25 75~200 17.5 12 17 15 44 M6X1.0 M10X1.25 11 11 15 76.5 32.5

Ø32 125~300 23.5 16 22 20.5 45.5 M8X1.25 M14X1.5 12.5 12.5 17 84 38.5

Ø40 125~300 23.5 16 28 20.5 55 M8X1.25 M14X1.5 14 14 17 93.5 38.5

Ø50 125~300 28.5 20 35 26 55.5 M10X1.5 M18X1.5 14 14 18 99 43.5

Ø63 125~300 28.5 20 35 26 57 M10X1.5 M18X1.5 16.5 16.5 18 100.5 43.5

Ø80 125~300 35.5 25 43 32.5 66 M16X2.0 M22X1.5 19 19 20 119.5 53.5

Ø100 125~300 35.5 30 59 32.5 75.5 M20X2.5 M26X1.5 23 23 22 129 53.5

Ø125 5~300 45 35 35 42 83 M22X2.5 M30X1.5 24.5 24.5 16 141 58

Ø125 type and standard type have the same dimensions. For dimensions not shown in those figures, refer to the standard type.

Rod End-Female Thread (Standard) (Ø12 ~ Ø20)

(Ø20 ~ Ø125)

Rod End-Male Thread (Ø12 ~ Ø20)

(Ø25 ~ Ø125)

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Dimensions-Double Acting Double Rod (AFW, ADFW)

Unit : mm


A B C C ØD ØE F FN KL TL TW L TL TW

Ø20 26 35 63 38 47 75 14 36 36 25.5 10 47 8 12 8

Ø25 29 39 74 39 49 84 17.5 40 40 28 12 52 12 15 10

Bore size K KK NKK ØO PA ØQ Rc(PT) T TN

Ø20 8 M5X0.8 M8X1.25 5.5 10.5 9 Depth 7 M5X0.8 4.5 18.5

Ø25 10 M6X1.0 M10X1.25 5.5 11 9 Depth 7 M5X0.8 5 22.5



Rod End-Male Thread

DepthDepth


Through hole

Ø20 ~ Ø25

Ø20 ~ Ø25

1

2

Unit : mm


Ø20 7 M6×1.0 9 10

Ø25 7 M6×1.0 9 10

KCC Co., Ltd.




Dimensions-Double Acting Double Rod (AFW, ADFW)


Rod End-Male Thread

Ø32 ~ Ø125

Ø32 ~ Ø125


Depth FDepth F


1

2

Unit : mm


A B C ØD ØE F FN K KK NKK ØO PAL TL TW L TL TW

Ø32 30.5 44.5 87.5 40.5 54.5 97.5 23.5 45 34 16 60 13 20.5 14 M8X1.25 M14X1.5 5.5 10.5

Ø40 40 54 97 50 64 107 23.5 52 40 16 69 13 20.5 14 M8X1.25 M14X1.5 5.5 12

Ø50 40.5 56.5 107.5 50.5 66.5 117.5 28.5 64 50 20 86 15 26 18 M10X1.5 M18X1.5 6.8 10.5

Ø63 42 58 109 52 68 119 28.5 77 60 20 103 15 26 18 M10X1.5 M18X1.5 9 15

Ø80 51 71 138 61 81 148 35.5 98 77 25 132 21 32.5 22 M16X2.0 M22X1.5 11 18

Ø100 60.5 84.5 147.5 70.5 94.5 157.5 35.5 117 94 30 156 27 32.5 27 M20X2.5 M26X1.5 11 23

Ø125 83 115 199 83 99 199 45 142 114 35 190 30 42 30 M22X2.5 M30X1.5 12.5 24.5

Bore size ØQ Rc(PT) T TN U W Z

Ø32 9 Depth 7 Rc(PT)1/8 7 28.5 4.5 49.5 14

Ø40 9 Depth 7 Rc(PT)1/8 7 28.5 5 57 14

Ø50 11 Depth 8 Rc(PT)1/4 8 33.5 7 71 18

Ø63 14 Depth 10.5 Rc(PT)1/4 8 33.5 7 84 18

Ø80 17.5 Depth 13.5 Rc(PT)3/8 10 43.5 6 104 22

Ø100 17.5 Depth 13.5 Rc(PT)3/8 12 43.5 6.5 123.5 22

Ø125 21.2 Depth 18.4 Rc(PT)3/8 16 58 11 162 32

Unit : mm


Ø32 7 M6X1.0 9 10

Ø40 7 M6X1.0 9 10

Ø50 8 M8X1.25 11 14

Ø63 10.5 M10X1.50 14 18

Ø80 13.5 M12X1.75 17.5 22

Ø100 13.5 M12X1.75 17.5 22

Ø125 18.4 M14X2.0 21.2 25

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Unit : mm

Bore size Without magnet (AF) With magnet (ADF)

A ØD FN T TNL TL TZ L TL TZ

Ø20 45.5 50 64 69.5 74 88 14 10 12 4.5 18.5

Ø25 51.5 56.5 74 71.5 76.5 94 17.5 12 15 5 22.5

Ø32 53.5 60.5 82 73.5 80.5 102 23.5 16 20.5 7 28.5

Ø40 68.5 76.5 97 89.5 96.5 118 23.5 16 20.5 7 28.5

Ø50 71 79 104.5 91 99 124.5 28.5 20 26 8 33.5

Ø63 78 86 111.5 98 106 131.5 28.5 20 26 8 33.5

Ø80 94.5 104.5 138 114.5 124.5 177 35.5 25 32.5 10 43.5

Ø100 113.5 125.5 157 133.5 145.5 133.5 35.5 30 32.5 12 43.5

Ø125 166 182 244 166 182 244 45 35 42 16 58

For dimensions not shown in these figures, refer to the standard type.



Rod End-Male Thread(Ø20 ~ Ø25)









KCC Co., Ltd.



Unit : mm

Bore size Without magnet (AF) With magnet (ADF)

A ØD FN T TNL TL TZ L TL TZ

Ø20 45.5 54.5 82.5 69.5 78.5 106.5 14 10 12 4.5 18.5

Ø25 51.5 61.5 96.5 71.5 81.5 116.5 17.5 12 15 5 22.5

Ø32 53.5 67.55 110.5 73.5 87.5 130.5 23.5 16 20.5 7 28.5

Ø40 68.5 83.5 125.5 89.5 103.5 146.5 23.5 16 20.5 7 28.5

Ø50 71 87 138 91 107 158 28.5 20 26 8 33.5

Ø63 78 94 145 98 114 165 28.5 20 26 8 33.5

Ø80 94.5 114.5 181.5 114.5 134.5 220.5 35.5 25 32.5 10 43.5

Ø100 113.5 137.5 200.5 133.5 157.5 177 35.5 30 32.5 12 43.5

Ø125 166 198 302 166 198 302 45 35 42 16 58

For dimensions not shown in these figures, refer to the standard type.

Multi-Step Stroke Cylinder (TW)

Dimensions-Multi-Step Stroke Cylinder (TW)











KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Unit : mm

Bore size ØC L MI MT MK ML MT T TL

Ø20 20 26 36 8 10 12.5 8 4.5 61

Ø25 20 29 36 8 10 12.5 8 5 64.5

Ø32 27 30.5 Ø38 6 14 16 6 7 72.5

Ø40 27 40 Ø46 6 14 16 6 7 82

Ø50 35 40.5 Ø57 8 16 20 8 8 91.5

Ø63 35 42 Ø68 10 16 20 10 8 95

Ø80 48 51 Ø90 12 20 28 12 10 119

Ø100 48 60.5 Ø110 14 20 28 14 12 134.5

Ø125 - 83 - - - - - 16 -

For dimensions not shown in these figues, refer to the AF series standard type.

Dimensions-Forward Stroke Adjustable (ASJ, BSJ)




ASJ : 0~10mm adjustmentBSJ : 0~20mm adjustmentRange of adjustment

KCC Co., Ltd.



Dimensions-Anti-Lateral Load (E) - AF, ADF

Unit : mm

Bore size Stroke A ØD ØEB FN ØEB L KK NKK PA PB T TL TN

Ø12 5~30 10.5 6 - 9 - 35 M3X0.5 M5X0.8 10 10 13.5 48.5 24

Ø16 5~30 12 8 - 10 - 38 M4X0.7 M6X1.0 10 10 13.5 51.5 25.5

Ø20 5~50 14 10 - 12 - 41 M5X0.8 M8X1.25 10.5 10.5 14.5 55.5 28.5

Ø25 5~50 17.5 12 17 15 17 44 M6X1.0 M10X1.25 11 11 15 59 32.5

Ø32 5~100 23.5 16 22 20.5 22 45.5 M8X1.25 M14X1.5 12.5 12.5 17 62.5 38.5

Ø40 5~100 23.5 16 28 20.5 28 55 M8X1.25 M14X1.5 14 14 17 72 38.5

Ø50 5~100 28.5 20 35 26 35 55.5 M10X1.5 M18X1.5 14 14 18 73.5 43.5

Ø63 5~100 28.5 20 35 26 35 57 M10X1.5 M18X1.5 16.5 16.5 18 75 43.5

Ø80 5~100 35.5 25 43 32.5 43 66 M16X2.0 M22X1.5 19 19 20 86 53.5

Ø100 5~100 35.5 30 59 32.5 59 75.5 M20X2.5 M26X1.5 23 23 22 97.5 53.5

Ø125 5~300 45 35 35 42 35 83 M22X2.5 M30X1.5 24.5 24.5 16 99 58

Ø125 type and standard type have the same dimensions. For dimensions not shown in those figures, refer to the standard type.


(Ø20 ~ Ø125)


(Ø25 ~ Ø125)

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


Dimensions-Scraper Attached Cylinder (MS)

Unit : mm


(AF)With magnet

(ADF) T TNL

Ø32 23 33 7 28.5

Ø40 29.5 39.5 12 33.5

Ø50 30.5 40.5 13 38.5

Ø63 36 46 13 38.5

Ø80 43.5 53.5 15 48.5

For dimensions not shown in those figures, refer to the standard type.


Rod End-Male Thread - (AF, ADF)


Type Non lubricated

Bore size Ø40, Ø50, Ø63, Ø80, Ø100

Temperature -20~150



Type Lubricated, Non lubricated

Bore size Ø40, Ø50, Ø63, Ø80, Ø100

Rod Material SUS304

Stainless Steel Piston Rod (SS)Head Resistant Cylinder (SV)


KCC Co., Ltd.



Unit : mm

Part no. Bore size A B C E ØG MM MI ØTDH10 TX

I(CP)12 Ø12 21.5 16 2.5 7 12 M5X0.8 6 5 +0.048 0 5 -0.2

-0.4

I(CP)16 Ø16 32 25 3 14 14 M6X1.0 8 5 +0.048 0 6.4 -0.2

-0.4

I(CP)20 Ø20 34 25 4 11.5 18 M8X1.25 8.5 8 +0.058 0 8 -0.2

-0.4

I(CP)25 Ø25 41 30 5 14 23 M10X1.25 10.5 10 +0.058 0 10 -0.2

-0.4

I(CP)32,40 Ø32,40 42 30 6 14 29 M14X1.5 14 10 +0.058 0 18 -0.3

-0.5

I(CP)50,63 Ø50,63 56 40 6.5 20 36 M18X1.5 18 14 +0.070 0 22 -0.3

-0.5

I(CP)80 Ø80 71 50 8 27 38 M22X1.5 21 18 +0.070 0 28 -0.3

-0.5

I(CP)100 Ø100 79 55 10 31 44 M26X1.5 21 22 +0.084 0 32 -0.3

-0.5

Unit : mm

Part no. Bore size A B C E ØG MM MI ØTDH10 TX TY TZ

Y(CP)12 Ø12 21.5 16 6 7 - M5X0.8 6 5 +0.048 0 5 -0.4

-0.2 10 14.6

Y(CP)16 Ø16 28 21 8 10 - M6X1.0 7 5 +0.048 0 6.4 -0.4

-0.2 12 16.6

Y(CP)20 Ø20 34 25 9.5 11.5 16 M8X1.25 8.5 8 +0.058 0 8 -0.4

-0.2 16 21

Y(CP)25 Ø25 41 30 14 14 20 M10X1.25 10.5 10 +0.058 0 10 -0.4

-0.2 20 25.6

Y(CP)32,40 Ø32,40 42 30 - 14 - M14X1.5 16 10 +0.058 0 18 -0.5

-0.3 36 41.6

Y(CP)50,63 Ø50,63 56 40 - 20 - M18X1.5 20 14 +0.070 0 22 -0.5

-0.3 44 50.6

Y(CP)80 Ø80 71 50 - 27 - M22X1.5 23 18 +0.070 0 28 -0.5

-0.3 56 64

Y(CP)100 Ø100 79 55 - 31 - M26X1.5 24 22 +0.084 0 32 -0.5

-0.3 64 72

Unit : mm

Part no. Bore size ØDd9 L1 L2 P W B Retaining ring

CJP(CP)12 Ø12 5 -0.03-0.06 2.5 7 12 M5X0.8 6 Type C 5 for axis

CJP(CP)16 Ø16 5 -0.03-0.06 3 14 14 M6X1.0 8 Type C 5 for axis

CJP(CP)20 Ø20 8 -0.04-0.076 4 11.5 18 M8X1.25 8.5 Type C 8 for axis

CJP(CP)25 Ø25 10 -0.04-0.076 5 14 23 M10X1.25 10.5 Type C 10 for axis

CJP(CP)32,40 Ø32,40 10 -0.04-0.076 6 14 29 M14X1.5 14 Type C 10 for axis

CJP(CP)50,63 Ø50,63 14 -0.05-0.076 6.5 20 36 M18X1.5 18 Type C 14 for axis



Unit : mm

Part no. Bore size d J A C

RN(CP)12 Ø12 M5X0.8 4 8 9.2

RN(CP)16 Ø16 M6X1.0 5 10 11.5

RN(CP)20 Ø20 M8X1.25 5 13 15

RN(CP)25 Ø25 M10X1.25 6 17 19.6

RN(CP)32,40 Ø32,40 M14X1.5 8 22 25.4

RN(CP)50,63 Ø50,63 M18X1.5 11 27 31.2

RN(CP)80 Ø80 M22X1.5 13 32 37.0

RN(CP)100 Ø100 M26X1.5 16 41 47.3


Material: Carbon Steel

Material: Carbon Steel Material: Carbon Steel

Material: Carbon Steel Material: Carbon Steel



Knuckle Joint Pin / Clevis Pin Rod End Nut


Material: Cast Iron

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Compact Guide Cylinder

AFG series

AFG series

AFGM-12-S30

Bore size (mm)Non-rotating accuracy

AFGM AFGLØ12

±0.07° ±0.10°Ø16Ø20

±0.06° ±0.09°Ø25Ø32

±0.06° ±0.08°Ø40Ø50

±0.05° ±0.06°Ø63Ø80

±0.04° ±0.05°Ø100

Non-Rotating Load Capability

Features

Built in magnet and rubber bumper (Standard).

Resists lateral loading and provides non-

rotating motion.

Sliding bearing and ball bearing are available

depending on applications.

Symbol


AFG M - 12 - S 30

How to Order

As to intermediate stroke (5, 10, 15, 20...), spacer of 5, 10, 15, 20mm width will be used.

Speci cations

SeriesAFG Compact guide cylinder

BearingM Sliding bearingL Ball bearing



Bore size12 Ø12 40 Ø4016 Ø16 50 Ø5020 Ø20 63 Ø6325 Ø25 80 Ø8032 Ø32 100 Ø100

Auto switch

Reed A/S Model Solid state A/S Model

Nil None Nil NoneA-72 D-A72K F-7NV D-F7NVKA-73 D-A73K F-7PV D-F7PVKA-80 D-A80K F-7BV D-F7BVK



Ø1210, 20, 30, 40, 50, 75, 100

Ø16Ø20

20, 30, 40, 50, 100Ø25Ø32

25, 50, 75, 100, 125, 150

Ø40Ø50Ø63Ø80

Ø100

Ex) AFGM20-S25 is produced by installing 5mm spacer in AFGM20-S30.

ActionDouble acting

Ø12, Ø16 Ø25 ~ Ø100

Fluid Air

Proof pressure 15kgf/cm2(1.5MPa)

Max. operating pressure 10kgf/cm2(1.0MPa)

Min. operating pressure 1.2kgf/cm2(0.12MPa) 1.0kgf/cm2(0.1MPa)Ambient & uid

temperature 5 ~ 60





KCC Co., Ltd.




AFG series


1 Rod Cover Aluminium Alloy White Alumite

2 Head Cover Aluminium Alloy White Alumite

3 Cylinder Tube Aluminium Alloy White Alumite

4 Piston (C) Aluminium Alloy -

5 Piston (R) Aluminium Alloy -

6 RodStainless Steel Ø12~Ø25

Carbon Steel Ø32~Ø100

7 Guide RodAFGM Carbon Steel Hard Chromium

PlatingAFGL Bearing Steel -

8 Plate Carbon Steel Nikel Plating

9 Urethane Damper Urethane -

Structure


10 Urethane Damper (C) Urethane -

11 Spacer Carbon Steel -

12 Rod Packing NBR -

13 Tube O-Ring NBR -

14 Magnet Synthetic Rubber -

15 Piston Packing NBR -

16 Plate Mounting Bolt Carbon Tool Steel -

17 Snap Ring (A) Carbon Tool Steel Phosphate Coating

18 Snap Ring (B) Carbon Tool Steel Phosphate Coating

19 Sliding Bearing - -

20 Ball Bearing - -

Unit : kg

Bore size (mm)

Standard stroke - AFGM(Sliding bearing)10 20 25 30 40 50 75 100 125 150

Ø12 0.24 0.28 - 0.31 0.35 0.39 0.50 0.60 - -Ø16 0.35 0.40 - 0.45 0.51 0.55 0.70 0.82 - -Ø20 - 0.71 - 0.79 0.87 0.97 1.15 1.34 - -Ø25 - 1.04 - 1.14 1.25 1.35 1.73 2.00 - -Ø32 - - 1.81 - - 2.20 2.58 2.98 3.39 3.78Ø40 - - 1.91 - - 2.50 2.72 3.31 3.82 4.13Ø50 - - 3.40 - - 3.96 4.52 5.06 5.63 6.19Ø63 - - 3.93 - - 4.55 5.15 5.77 6.39 7.01Ø80 - - 6.99 - - 7.92 88.82 9.74 10.67 11.58

Ø100 - - 11.04 - - 12.35 13.65 14.98 16.31 17.64

Unit : kg

Bore size (mm)

Standard stroke - AFGL(Ball bearing)10 20 25 30 40 50 75 100 125 150

Ø12 0.24 0.26 - 0.30 0.35 0.39 0.48 0.56 - -Ø16 0.35 0.38 - 0.43 0.53 0.59 0.68 0.80 - -Ø20 - 0.72 - 0.80 0.91 0.99 1.18 1.35 - -Ø25 - 1.05 - 1.15 1.32 1.43 1.71 1.91 - -Ø32 - - 1.53 - - 1.87 2.29 2.65 3.01 3.37Ø40 - - 1.69 - - 2.04 2.50 2.86 3.22 3.58Ø50 - - 2.83 - - 3.31 3.91 4.40 4.89 5.38Ø63 - - 3.47 - - 4.00 4.66 5.20 5.74 6.28Ø80 - - 5.54 - - 6.43 8.00 8.84 9.68 10.52

Ø100 - - 10.27 - - 11.46 13.71 14.89 16.07 17.26

Mass

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS


AFG series

Unit : mm

Bore size A B C CA CB D

DADB E EA

EB

AFGM AFGL

AFGM AFGL 30ST 30ST~ 50ST 50ST 10ST 20ST 30ST 40ST, 50ST 50ST

Ø12 26 60 13 12.5 13 6 8 6 46 8 5 0 5 34 3 13 13 23 28

Ø16 30 67 15 14.5 15 8 10 8 50 8 5 0 5 34 5 20 20 30 35

Ø20 36 85 18 17.5 18 10 12 10 58 10 6 3 5 47 - 12 25 35 45

Ø25 42 95 21 20.5 21 12 16 13 68 10 6 3 5 47 - 18 18 37 48

Dimensions-Ø12 ~ Ø25 / AFGM, AFGL

Bore size F

FAFB FC FD FL FH FM FLL GA GB GC GD GM GL LA LB

30ST 30ST

Ø12 7 20 40 25 4.3 8 13.5 18 M5XP0.8 12 18 50 23 M3 M4XP0.7 10 29 42

Ø16 7 24 44 27 4.3 8 12.5 22 M5XP0.8 12 22 56 24 M3 M5XP0.8 12 33 46

Ø20 18 24 44 31 5.5 9.5 13.5 24 M5XP0.8 13 24 72 28 M5 M5XP0.8 13 37 53

Ø25 18 24 44 35 5.5 9.5 14.5 30 M6XP1.0 15 30 82 34 M5 M6XP1.0 15 37.5 53.5

Bore size

LL

P PA PB QA QB QM R S UU UA UB UC UDAFGM AFGL

30ST 30ST~ 50ST 50ST 10SST 20ST 30ST 40ST, 50ST 50ST

Ø12 42 47 76 45 55 55 65 70 M5XP0.8 11 8.5 14 48 M4XP0.7 58 22 23 3 3.5 3 6

Ø16 46 51 80 51 66 66 76 81 M5XP0.8 11 8 16 54 M5XP0.8 65 25 24 3 3.5 3 6

Ø20 56 58 100 - 65 78 88 95 Rc(PT) 1/8 10.5 9 18 70 M5XP0.8 83 30 28 3 3.5 3 6

Ø25 56.5 58.5 100.5 - 71.5 71.5 90.5 101.5 Rc(PT) 1/8 11.5 9.5 26 78 M6XP1.0 93 38 34 4 4.5 3 6

For intermediate stroke, spacer will be used.

KCC Co., Ltd.


PNEUMATIC & HYDRAULIC AFG seriesCompact Guide Cylinder

Unit : mm


DAE EA

EB

AFGM AFGL

AFGM AFGL 25ST 50ST 75ST 100ST 125ST 150ST 25ST 50ST 75ST 100ST 125ST 150ST

Ø32 53 114 27 25 26 16 20 16 12 10 23.2 41.2 46.2 46.2 51.2 51.2 4.4 41.4 46.4 46.4 66.4 66.4

Ø40 57 124 31 25 26 16 20 16 12 10 16.7 34.7 39.7 39.7 44.7 44.7 0 34.9 39.9 39.9 59.9 59.9

Ø50 69 140 39 29 30 20 25 20 16 12 27.7 39.7 49.7 49.7 54.7 54.7 2.9 44.9 49.9 49.9 69.9 69.9

Ø63 82 150 45.5 29 36.5 20 25 20 16 12 22.7 34.7 44.7 44.7 49.7 49.7 0 39.9 44.9 44.9 64.9 64.9


Bore size P PA PB QA QB QM R S SA SB T TA TB TL TM U UA UB UC UL

Ø32 1/8 12.5 9 30 96 M8XP1.25 112 48 2 1 16 5 100 11 M8XP1.25 42 4 4.5 3 6

Ø40 1/8 14 10.5 30 106 M8XP1.25 122 48 2 1 17 10 110 11 M8XP1.25 50 4 4.5 3 6

Ø50 1/4 14 11 40 120 M10XP1.5 138 56 2 1 17 10 124 12.5 M10XP1.5 56 5 6 4 8

Ø63 1/4 16.5 13.5 50 130 M10XP1.5 148 69 2 0 19 10 132 15 M10XP1.5 66 5 6 4 8


Bore size GA GB GL GM I LA LB

LL

AFGM AFGL

25ST 50ST 75ST 100ST 125ST 150ST 25ST 50ST 75ST 100ST 125ST 150ST

Ø32 38 80 20 M8XP1.25 22 37.5 59.5 82.7 100.7 105.7 105.7 110.7 110.7 63.9 100.9 105.9 105.9 125.9 125.9

Ø40 38 90 20 M8XP1.25 22 44 66 82.7 100.7 105.7 105.7 110.7 110.7 63.9 100.9 105.9 105.9 125.9 125.9

Ø50 44 100 25 M10XP1.5 22 44 72 99.7 111.7 121.7 121.7 126.7 126.7 74.9 116.9 121.9 121.9 141.9 141.9

Ø63 44 110 25 M10XP1.5 31 49 77 99.7 111.7 121.7 121.7 126.7 126.7 74.9 116.9 121.9 121.9 141.9 141.9

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

AFG seriesCompact Guide Cylinder

Unit : mm


DAE EA

EB

AFGM AFGL

AFGM AFGL 25ST 50ST 75ST, 100ST 125ST, 150ST 25ST, 50ST 75ST, 100ST, 125ST, 150ST

Ø80 96.5 204 50 38.5 46.5 25 30 25 22 18 23.3 25.3 53.3 58.3 8.5 72.5

Ø100 114.5 238 58 41 56.5 30 36 30 25 20 18.8 23.8 48.8 53.8 4.0 73


Bore size P PA PB PC QA QB QM R S SA SB T TA TB TL TM

Ø80 3/8 19 15.2 28 60 174 M12XP1.75 198 80 6.5 10 20.5 15.5 182 18 M12XP1.75

Ø100 3/8 22.5 18.8 35 64 200 M14XP2.0 231 95 9 10.5 20.5 25 211 21 M14XP2.0


Bore size F FA FB FC FD FL GA GB GL GM LA LB

LL

AFGM AFGL

25ST 50ST 75ST ,100ST 125ST ,150ST

25ST

,50ST75ST, 100ST, 125ST, 150ST

Ø80 20.5 15.5 100 11 17.5 11 56 155 30 M12XP1.75 56.5 96.5 119.8 121.8 149.8 154.8 105 169

Ø100 20.5 25 120 13 20 13 62 184 35 M14XP2.0 66 111 129.8 134.8 159.8 164.8 115 184

KCC Co., Ltd.



Free Mount Cylinder

FM/FMD series

FM/FMD series

How to Order

FM - 20 - S 15 D

Series

FM Single rod without magnetfree mount cylinder

FMD Single rod with built-in magnetfree mount cylinder

ActionD Double acting



Port type

Nil M5×0.8(Ø32 : Rc(PT) 1/8)

G G 1/8 (Only for Ø32)

Bore size6 Ø6

10 Ø1016 Ø1620 Ø2025 Ø2532 Ø32

Symbol


Features

With non-lubricated seal (Standard). The multiple surface direct mounting with a

square body enables spacesaving designs for equipment.


Ø65, 10, 15, 20, 25, 30Ø10

Ø16Ø20

5, 10, 15, 20, 25, 30, 40, 50Ø25

Ø30


state A/S Model

A-90 D-A90(V)K F-9N(V) D-F9N(V)KA-93 D-A93(V)K F-9P(V) D-F9P(V)KA-96 D-A96(V)K F-9B(V) D-F9B(V)K Only for auto switch attached type. Refer to Auto Switch Catalogue for more

information.

Speci cations Tightening Torque

Bore size (mm) Screw dia. Proper tightening torque(N m)

Ø6, Ø10 M3 1.08±10%

Ø16 M4 2.45±10%

Ø20, Ø25 M5 5.10±10%

Ø16 M6 8.04±10%


Bore size Ø6 Ø10 Ø16 Ø20 Ø25 Ø32

Fluid Air




0.6kgf/cm2 (0.06MPa) 0.5kgf/cm2 (0.05MPa)

Ambient & uid temperature 5 ~60






Rod end thread Male thread (Standard)

FM-20-S15D

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

FM/FMD seriesFree Mount Cylinder

Structure


1 Cylinder Tube Aluminium Alloy

2 Head Cover Brass, Aluminium Alloy

3 Piston (A) Brass, Aluminium Alloy

4 Piston (R) Brass, Aluminium Alloy

5 Piston (C) Aluminium Alloy

6 Piston Rod Stainless Steel

7 Dumper Urethane

8 Snap Ring Carbon Tool Steel


9 Rod End Nut Carbon Steel

10 Bush Sintered Alloy

11 Rod Packing NBR

12 Piston Packing NBR

13 Tube O-Ring NBR

14 Magnet -

15 Rod O-Ring NBR

FM10~32 (Without magnet) FMD10~32 (With built-in magnet)

FM6 (Without magnet) FMD6 (With built-in magnet)

MassFMDUnit : g

Cylinder stroke (mm)

Bore size (mm)

Ø6 Ø10 Ø16 Ø20 Ø25 Ø32

5 22 36 50 95 176 262

10 25 40 56 106 193 286

15 28 44 62 117 210 310

20 31 48 68 128 227 334

25 34 52 74 139 244 358

30 37 56 80 150 261 382

40 - - - 172 295 430

50 - - - 194 329 478

Unit : g

Cylinder stroke (mm)

Bore size (mm)

Ø6 Ø10 Ø16 Ø20 Ø25 Ø32

5 27 41 75 128 230 335

10 35 50 86 143 252 364

15 38 54 92 154 269 388

20 41 58 98 165 286 412

25 44 62 104 176 303 436

30 47 66 110 187 320 460

40 - - - 209 354 508

50 - - - 231 388 556

FM

KCC Co., Ltd.


PNEUMATIC & HYDRAULIC FM/FMD seriesFree Mount Cylinder

Dimensions

Unit : mm

Bore size A A' B C D E GA GB H J K L MM

Ø6 7 - 13 22 3 7 15 10 13 10 17 - M3×0.5

Ø10 10 - 15 24 4 7 16.5 10 16 11 18 - M4×0.7

Ø16 11 12.5 20 32 6 7 16.5 11.5 16 14 25 5 M5×0.8

Ø20 12 14 26 40 8 9 19 11 18.7 16 30 6 M6×1.0

Ø25 15.5 18 32 50 10 10 21.5 13 23 20 38 8 M8×1.25

Ø32 19.5 22 40 62 12 11 23 12.5 27 24 48 10 M10×1.25

Bore size NN P Q QA R TWithout

magnet (FM)With magnet

(FMD)S Z S Z

Ø6 M3×0.5 Depth5 3.2 - - 7 6 Depth 4.8 33 46 33 46

Ø10 M3×0.5 Depth5 3.2 - - 9 6 Depth 5 36 52 36 52

Ø16 M4×0.7 Depth6 4.5 4 2 12 7.6 Depth 6.5 30 46 40 56

Ø20 M5×0.8 Depth8 5.5 9 4.5 16 9.3 Depth 8 36 54.7 46 64.7

Ø25 M5×0.8 Depth8 5.5 9 4.5 20 9.3 Depth 9 40 63 50 73

Ø32 M6×1.0 Depth9 6.6 13.5 4.5 24 11 Depth11.5 42 69 52 79

Ø6, Ø10

Ø16, Ø20, Ø25, Ø32

Unit : mmBore size KK T H C Qty

Ø6 M3×0.5 1.8 5.5 6.4 2

Ø10 M4×0.7 2.4 7 8.1 2

Ø16 M5×0.8 4 8 9.2 1

Ø20 M6×1.0 5 10 11.5 1

Ø25 M8×1.25 5 13 15.0 1

Ø32 M10×1.25 6 17 19.6 1


Rod End Nut

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Rod Ends for Pneumatic Cylinder

Custom-Made Rod Ends

- × KA1Pneumatic Cylinder Model Code

KA1 KA2KA0

KA4 KA5KA3

KA7KA6

KA10 KA9

KA13KA12

KA16KA15

KA8

KA11

KA14

KA17

Radius

1. For some products dotted line parts may not exist. 2. For dimensional tolerances and end finishings not shown in these figures will be process according to KCC regulation. 3. " * " is dimension of rod diameter(D) after chamfering. Inform KCC if there is dimension change. Following are standard dimension. D 6 D-1mm 6<D 25 D-2mm D>25 D-4mm


D

KCC Co., Ltd.



Rod Ends for Pneumatic Cylinder


KA19 KA20KA18

KA22 KA23KA21

KA25KA24

KA28KA27

KA31KA30

KA34KA33

KA26

KA29

KA32

4-sideChamfering

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Tie Rod for Pneumatic Cylinder

Custom-Made Tie Rod

Custom-Made Tie Rod

CT2 (ACM Series)CT1 (ACM Series)

CT3 (ACL Series)

Pneumatic Cylinder Model Code - CT1

KCC Co., Ltd.


PNEUMATIC & HYDRAULIC KBP seriesBooster Cylinder

KBP - PP 150 / 125 - 120 H - A54

How to Order

KBP series

TypeDI Direct pressure typePP Pre-pressure type

SeriesKBP Booster cylinder

Bore size Oil pressure Stroke Output oil capacity

Boosting ratio

10080 80kgf/cm2 (8MPa)

12059cm3(cc) 1:16

55 55kgf/cm2 (5.5MPa) 84cm3(cc) 1:1140 40kgf/cm2 (4MPa) 115cm3(cc) 1:8

150

180 180kgf/cm2 (18MPa)

120

59cm3(cc) 1:36125 125kgf/cm2 (12.5MPa) 84cm3(cc) 1:2590 90kgf/cm2 (9MPa) 115cm3(cc) 1:1870 70kgf/cm2 (7MPa) 150cm3(cc) 1:14

125 125kgf/cm2 (12.5MPa)200

141cm3(cc) 1:2590 90kgf/cm2 (9MPa) 192cm3(cc) 1:1870 70kgf/cm2 (7MPa) 251cm3(cc) 1:14

300

180 180kgf/cm2 (18MPa)120

235cm3(cc) 1:36125 125kgf/cm2 (12.5MPa) 339cm3(cc) 1:2570 70kgf/cm2 (7MPa) 603cm3(cc) 1:14180 180kgf/cm2 (18MPa)

200392cm3(cc) 1:36

125 125kgf/cm2 (12.5MPa) 565cm3(cc) 1:2570 70kgf/cm2 (7MPa) 1005cm3(cc) 1:14

Ø300 only available for pre-pressure type. Standard type with aluminium diecast cover and U packing.

For AC4C made cover and Quardring packing, consult KCC.

Auto switchNil NoneH With built-in magnet

Built-in magnet is inapplicable to Ø300 type. Auto switch is attaching on tie rod of

pneumatic cylinder. Select a hydraulic cylinder(KP70/140HC)

with piston compact seal, without cushion for booster.

KBP-PP-150 / 125-120KBP-DI-100 / 80-120

Symbol

Features

System converts air to high oil pressure for high prower applications. High output of air pressure, up to 8~36

times is available and can be integrated with hydraulic equipment.

1. The booster cylinder must be installed higher than the hydraulic actuator and pipes to prevent air release and reverse flow of hydraulic fluid.2. With a slight increase in pressure by mere 0.1kgf/cm2 at the supply side, the output will multiply depending on the sending ratio. Care must be taken.3. If rapid speed is required, the pipe size must be large enough for the purpose, and a quick exhaust valve should be installed.4. A filter and regulator should be installed before the air valve to ensure easy pressure adjustment and clean air supply.5. The discharge volume of the booster cylinder should be the same as the actual capacity of the cylinder.

PrecautionsSpeci cationsWorking oil Petroleum based fluid

Ambient & uid temperature 5~60

Air pressure

Working uid Air

Lubrication Not requiredOperating pressure 0~7kgf/cm2 (0~0.7MPa)


state A/S Model

Nil None Nil NoneA54 D-A54K F59 D-F59KA56 D-A56K F5P D-F5PKA64 D-A64K J59 D-J59K


F9B D-F9B(V)K Only for auto switch attached type. Refer to Auto Switch Catalogue for more

information.

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

KBP seriesBooster Cylinder

Circuit

Direct Compressed TypeTo be used if the discharge volume is being specified.

Pre-compressed TypeIf the stroke of the hydraulic actuator is long, or large flow is required, the pre-compressed type is used to enable rapid movement to the pressure section by air, and then to pressurize using the discharge volume.

1. Rapid Feed Stroke Cylinder rod is moved to a certain distance by the hydraulic pressure which has the same pressure as the air pressure pass through solenoid valve 1 when solenoid is ON.

2. Pressure Stroke The booster piston is pressurized by the solenoid valve 2 generating high hydraulic pressure required in various processes (clamping, press and etc).

3. Return Stroke Booster Piston and the cylinder pistons are returned by the solenoid valve 1 and 2.

KCC Co., Ltd.


PNEUMATIC & HYDRAULIC KBP seriesBooster Cylinder

Structure

5


1 Rod Cover Aluminium Alloy -

2 Head Cover Aluminium Alloy -

3 Cylinder Tube Aluminium -

4 Piston Aluminium Alloy -


6 Tube Carbon Steel -

7 LB Ass'y Zinc Plate -

8 Tie Rod Carbon Steel -

9 Oil Tank Aluminium -

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

KBP seriesBooster Cylinder

Dimensions-Ø100, Ø150

Unit : mm

Bore size ØD L LH LS LX LY LZ N T TL

Ø100 Ø100 55 70 80 138 160 (197) Ø6.5 28 105

Ø150 Ø150 31 110 61 180 200 (258) Ø7 28 105

Dimensions-Ø300 Pre-Pressure

Air-hydro convertor is sold separately.

Air-hydro convertor is sold separately.

Direct Pressure (KBP-DI)

Pre-Pressure (KBP-PP)

KCC Co., Ltd.


PNEUMATIC & HYDRAULIC CCTS seriesAir-Hydro Converter

CCTS - 63 - 100

How to Order

CCTS series

SeriesCCTS Air-hydro converter

Bore size

Bore sizeConverter

nominal size (mm)

Air port size Oil port size

63 Ø63 Rc(PT)3/8 Rc(PT)3/4100 Ø100 Rc(PT)1/2 Rc(PT)3/4160 Ø160 Rc(PT)3/4 Rc(PT)3/4

Stroke50, 100, 150, 200, 250, 300, 400, 450, 500, 600, 700, 800

Contact us for other stroke.

Converter nominal size

(mm)

Standard effective oil level stroke (mm) Limited ow /min50 100 150 200 250 300 400 500 600 700 800

Ø63 150 300 450 600 740 890 1190 1480 1780 - - 36

Ø100 370 750 1120 1510 1870 2260 3010 3770 4520 - - 88

Ø160 - 1830 - 3660 - 5490 7320 9150 10980 12810 14640 217

Symbol

Features

It converts air pressure to equivalent hydraulic pressure. The hydraulic pressure is used to operate an actuator. It solves the sticking and slipping problems

with low speed operations.

Speci cations

Fluid Turbine Oil (40~100mm2/S)


Operating pressure 0~7kgf/cm2 (0~0.7MPa)


KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

CCTS seriesAir-Hydro Converter

Dimensions

Unit : mm

Type Air port Oil port A B C 4-ØM D E F G H I

Ø63 Rc(PT)3/8 Rc(PT)3/4 105 87 64 8.5 88 45 86 3 53 30

Ø100 Rc(PT)1/2 Rc(PT)3/4 152 127 95.5 13 136 72 130 7 63 36

Type J K N O 4-P Q R 4-S T U 4-V Y

Ø63 7 2 72 36 M5×0.8 - - - - - - 28

Ø100 7 8 72 36 M5×0.8 85 32.5 M5×0.8 100 40 M6×1.0 35

Stroke L 50 100 150 200 250 300 400 500 600 700 800

Ø63 245 295 345 395 445 495 595 695 795 - -Ø100 255 305 355 405 455 505 605 705 805 - -Ø160 - 272 - 412 - 552 662 802 922 1042 1152

CCTS 63, 100 CCTS 160

Air port size Rc(PT)

Oil draining hole

Oil port sizeRc(PT) 3/4 Oil draining hole Oil port size

Air port Rc(PT) 3/4

Mounting hole

KCC Co., Ltd.


PNEUMATIC & HYDRAULIC CCTS seriesAir-Hydro Converter

Application Circuit

1) Dual Speed Control Circuit

The standard covalence and transformation circuits are used, and both directions of the cylinder are controlled.

Application - Feed at low or constant velocity - Cutting motion of machine tools - Valve open/close - Vertically moving load - Industrial machinery - Woodworking machine and etc

2) Rotary Cylinder Circuit

The Rotary Cylinder Circuit controls speed of the rotary cylinders. The foregoing cylinder is added to a rotary cylinder to enable various circuit configurations. A connection valve is installed to compensate the leakage inside the rotary cylinder.

Application - Industrial robots - Conveyor - Paint equipment - Valve open/close - Turntable

3) Intermediate Stop Circuit

This is used for reliable intermediate stopping.

Application - Spot welding machine - Machine tool - Valve open/close

4) Locking Circuit

This is used for intermediate stopping in forward and reverse movements. Even the pneumatic source is blocked, this circuit ensures a reliable locking.

Application - Valve open/close - Vertical moving load - Welding machine

Key points in applying circuit design Dual circuit as the standard circuit

A converter is fitted at the rod side and at the head side of cylinder each, to prevent air inflow on occurrence of leak at the cylinder piston packing, and this is applied as the standard circuit.

Meter-out circuit control The assembly will control the oil that is returned from a cylinder to a converter.

Flow Rate Setup Select the pipe, nipples and assembly to satisfy the required flow.

Cautions in cylinder selection The cylinder must be of the low pressure type. (G or L type) There is a magnet integrated type too. (Switch is sold separately)

KCC Co., Ltd.



Pneumatic Cylinder

Reference Data

AJP

KGUA

ACP

ACD

ACS2

ACS3

ACS4

ACS5

ACR

ACM

ACL

ACX

KLC

KLCS

AF, ADF

AFG

FM, FMD

Custom-Made

Rod EndsCustom-

Made Tie Rods

KBP

CCTS

Application Circuit

5) Low Speed Stable Circuit

This is an example of 5~10 filters being fitted in front and rear of a throttle valve in order to facilitate stable movement at low speed and to prevent any adverse effect of foreign materials in the hydraulic fluid. The throttle valve should be in V-groove shape.There is a case where hydraulic fluid of high viscosity is stably used at 10mm/min.If the cylinder speed is less than 40mm/min, use this control circuit.

Application - Cutting motion of machine tool - Medical device - Feed system in industrial machinery - Camera processing machine - Semi-conductor manufacturing equipment - Testing devices

6) 2 Stage-Speed Control Circuit

The circuit for 2 stage-speed transmission for rapid feed and cutting feed, enables a step feed, multiple program-transmissions when fitted with solenoid and throttle valves, and absorbing of impact during switching when fitted with mechanical valves.

Application - Cutting feed of machine tool - Butterfly valve open/close - cushioning device

7) Synchronising Circuit

The synchronising circuit is used to synchronise multiple cylinders. If the cylinder rods are connected, synchronising is satisfactory; if they are not connected, synchronising is poor after the air valve is being switched. The cushion packing must be removed with this circuit.

Application - Vertical table feed - Arm synchronising - Lifter - Extruder

8) Impact Prevention Circuit

This is used for shock absorbers and on the spot where impact is being made by falling weights.

Application - Lifter - Conveyor - Packing machine - Dental lab equipment

9) Auxiliary Circuit for Booster This is used for RAM return in air-hydro boosters.

Application - Dental lab equipment - Mold

CCTS seriesAir-Hydro Converter

€¦ · 01| pneumatic cylinder reference data [1] - 2 mini pin cylinder / ajp [1] - 14 guide unit...

Documents