010 773 catalogue 22 4 separators
TRANSCRIPT
Grease separators for interior installation
Grease separators for underground installation
Oil-/Fuel separators / Coalescence separators
Separators
PPoollyy
eetthhyy
lleennee WWaarrrraannttyy
202 YeY ars
Wastewater treatment
118 Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
............................ 122
............................. 123
........................... 124
................................. 125
..................................... 126
..................................... 127
...................................... 128
........................................... 129
.......................................... 136
.................. 137
“G” NS 1/2/4
“G” NS 7/10/15/20/25/30/35
........................... 143
........................... 144
.................................... 145
........................ 146
1) Odour emissions shouldbe avoided during grease disposal
2) Grease must beevacuated regularly
Grease separators for free standing installation
For reasons of space, thegrease separator system must be installed outside the building
Grease separators for underground installation
During tank filling, servicingor vehicle cleaning, light liquids occur.
Oil-/Fuel separatorsCoalescence separators
“E+S” PV NS 2/4/7/10with program-controlled disposal systemand Shredder-Mix-System
“E+S” M NS 2/4/7/10with manually controlled disposal systemand Shredder-Mix-System
“D+S-P1” NS 2/4/7/10with direct disposal and programcontrolled Shredder-Mix-System
“D+S” NS 2/4/7/10with direct disposaland Shredder-Mix-System
“D” NS 2/4/7/10with direct disposal
“G” NS 2/4/7/10basic-version
SE CNS NS 2-25for self-disposal
“Under sink”basic-version (limited amounts of fat)
Coalescence separatorNS 3 - NS 15
Coalescence separatorNS 3/6
Oil/fuel separatorNS 3 - NS 15
Oil/fuel separator NS 1.5
119Catalogue 2.2
Grease separatorsfor interior installation
PPoollyy
eetthhyy
lleennee WWaarrrraannttyy
202 YeY ars
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
120 Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
G rease separator made of polymer mater ia l - the sanitat ion-free al ternat ive
KESSEL has been manufacturing draining systems made ofpolymer for a long time. “The certification confirms our
innovative strength, the high level of quality of our pro-
ducts and synthetic material as the material of the future.”
The German Institute for Structural Engineering (DIBt) hasgranted site-inspection certification. This makes KESSEL thefirst manufacturer on the German market to be granted suchan inspection certificate.
“The polyethylene material creates significant advantages
for planners, decision makers and processing workers,
such as long-term watertightness and fracture resistance,
the relatively low weight, short installation times and last
but not least an attractive price.”
KESSEL extends the warranty period for tanks
and upper cover sections beyond the
statutory requirement to 20 years.
This covers the airtightness,
usability and static safety of
these components.
Simple and fast installation
Thanks to the low weight and straightforward KESSEL fasteningtechnology, the KESSEL round-design grease separator system caneasily be dismantled to minimum component size, allowing it tobe set up in rooms with only very narrow access.
Odour-proof
The single-piece grease separator tank made of polyethylene isboth gas and waterproof. The covers are sealed tight with a sea-ling ring and fast-action clamp.
Resistant to aggressive fatty acids
The polyethylene material used guarantees a long service life sincethere is no early damage to the material e.g. through corrosion.
Compact design, low weight
Minimum dimensions mean easy installatione.g. via narrow stairs into cramped cellarrooms where there is little installationspace.
Poly
et
hylene Warranty
Poly
et
hylene Warranty
20 Years
- typical advantages
Fully automated operationOdour free disposal and cleaningMixing of separator contentswith Shredder-Mix-SystemOptimal cleaning with only a single pumpOptional remote control
Grease Separator “E+S” PV
Odour free disposal and cleaningMixing of separator contentswith Shredder-Mix-SystemComplete cleaningof interior separator wallsDisposal through pre-installeddisposal pipe by pumpSimple On / Off controlManual change-over from mixingto disposal
Grease Separator “E+S” M
Odour free disposal and cleaningMixing of separator contentswith Shredder-Mix-System Simple controlsNo warm water connection necessaryDisposal through pre-installed disposal pipeFully automated operation exceptfor disposal (version D+S-P1)
Grease Separator D+S / D+S-P1
Products see pages 124/125Product see page 123Product see page 122
121Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Easy transport
Their low weight allows KESSEL greaseseparators to be transported easily. Thespecial base structure of the separatorsallows problem-free transport by meansof a forklift.
Telescopic upper section is standard
For installation of the tank in the ground, theupper cover section can be vertically adjustedby up to 500 mm and tilted through up to 5° foradaptation to the ground level. The odour-proofcovers are available in the load classes A/B, D.
Absolutely tight
PE-HD is absolutely waterproof. The individualelements and pipe connections are sealed usingsealing rings according to DIN EN 681-1 whichseal both axially and radially, thus guaranteeinga high degree of safety.
Grease separators made of polymer
Closed cover disposalOdour free disposal possiblewith non-solidified greasesCleaning possible with open coversDisposal through pre-installed disposal pipe
Grease Separator D
for free standing or underground installation
Open cover disposalLow cost modelNS 2 to NS 35Disposal with open coversDisposal system available upon request
Grease Separator G
Regular disposal of grease and sludgeeven during separator operationSeparate disposal of grease and sludgeEnvironmentally friendly recyclingof collected wasteDisposal costs reduced since cleanwater remains in separator, only greaseand sludge are removedDisposal requires no additional water forrinsing, cleaning or re-filling which savesvaluable drinking waterOn-site assembly available
Grease Separator SE CNS
SPÜLEN
EINAUS
MOTORSCHUTZ
HEIZREGLER
MOTORSCHUTZ
HEIZEN
MISCHEN
Product see page 128Products see pages 127 / 136 - 137Product see page 126
Easy to clean
Crust formation on the walls is prevented by thesurface finish, which is similar to wax. The systemis easy to clean, leading to shorter disposal timesand lower cleaning water consumption.
SonicControl level sensing system with ultra sonic sensor
for the measurement, display and control of the grease layer thickness in a grease separator
Disposal costs are saved
by extending the disposal intervals.
Environment protection
Disposal of clean water no longer necessary,takes the pressure off resources.
User-friendly operation
thanks to the interactive control unit with digitaldisplay and userfriendly interface.
Product see page 131
bb1
�420l
a
h2 h1h3
� �
Dimensioned illustration
Ø = Outer diameter b1 = Installation dimensions
Ø
110110160160
a
1030150016002430
b
670730990990
h1
930930
11301130
h2
1000100012001200
h3
1310131015601560
l
1250181018502700
Sludge trap
200 l400 l700 l
1000 l
Wastewater content
Separator
212 l354 l567 l794 l
Grease
separator
106 l177 l302 l423 l
Nominal size
NS 2NS 4NS 7NS 10
b1
950100012201220
x
Access opening
Article descriptionIllustration
Grease separator Euro “E+S” PV according to EN 1825NS 2/4/7/10 with program-controlled disposal unitand Shredder-Mix-System for free standing installation in frost free areas
Art. # 93 004.00 / P1 Version in flow direction right
Nominal size* Article #
NS 2NS 4NS 7NS 10
150 kg165 kg200 kg225 kg* other sizes available on request
for free standing installation in frost free areas
Installation site
93 002.50 / P193 004.50 / P193 007.50 / P193 010.50 / P1
93 002.00 / P193 004.00 / P193 007.00 / P193 010.00 / P1
Pump left Pump right
Pump size
2.6 kW2.6 kW2.6 kW4.0 kW
Grease separator Euro “E+S” PV NS ... with program-controlled disposal system, Shredder-Mix-System, according to EN 1825, made of polymerFor free standing installation in frost free areas, with integra-ted sludge trap, domed covers made of polymer, with snapclosures and sealed odour-tight, inspection window, withdisposal system PV (program-controlled and fully automated)System KESSEL with switching distribution and actuator,with jet nozzle and conical nozzle for mixing and rinsing,with exterior submersible pump (IP 68), with integratedmacerator and closure valve, controls in flow direction left orright as desired (Protection IP 68, 400 V, 50 Hz, with 2.6 kW> 25 m3/h at 0.7 bar middle pumping height and/or 4.0 kW> 30 m3/h at 1.0 bar middle pumping height), with controlcabinet, program-controlled and fully automated, manualoperation, with two solenoid valves 1 inch, with inlet for rin-sing and filling according to DIN 1988, disposal flange Ø 65, PN 10 according to DIN 2501, Storz-B-Coupling 2 1/2 inchfor disposal trucks. Inlet and outlet Ø ... for synthetic material pipes in: PE-HD (according to DIN 19537); PP, AS or HT according to DIN 19560.Sludge trap content:...... Liter Manufacturer: KESSELSeparator content: ...... Liter Article #: ........................Weight: ...... kg Certification no. Z-54.1-474
Delivery: System completely assembled.On-site welding available on request.
Accessories
Page 131 - 134
Weight approx.
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2122
Grease separator Euro “E+S” M according to EN 1825NS 2/4/7/10 with manually controlled disposal systemand Shredder-Mix-System for free standing installation in frost free areas
Article descriptionIllustration
Grease separator Euro “E+S” M NS ...with manually controlled disposal system,Shredder-Mix-System, according to EN 1825,made of polymerFor free standing installation in frost free areas, with integra-ted sludge trap, domed covers made of polymer, with snapclosures and sealed odour-tight, inspection window, with(manual) disposal system M System KESSEL with switchingdistribution, with jet nozzle and conical nozzle for mixing andrinsing, with exterior submersible pump (IP 68), with integra-ted macerator and closure valve, controls in flow directionleft or right as desired (Protection IP 68, 400 V, 50 Hz, with2.6 kW > 25 m3/h at 0.7 bar middle pumping height and/or 4.0 kW > 30 m3/h at 1.0 bar middle pumping height), withcontrol cabinet, with inlet for rinsing and filling according to DIN 1988, disposal flange Ø 65, PN 10 according to DIN 2501, Storz-B-Coupling 2 1/2 inch for disposal trucks. Inlet and outlet Ø ... for synthetic material pipes in: PE-HD (according to DIN 19537); PP, AS or HT according to DIN 19560.Sludge trap content:...... Liter Manufacturer: KESSELSeparator content: ...... Liter Article #: .......................Weight: ...... kg Certification no. Z-54.1-474
Delivery: System completely assembled.On-site welding available on request.
Accessories
Page 131 - 134
Art. # 93 004.00/M1 Version in flow direction right
bb1
�420l
a
h2 h1h3
� �
Dimensioned illustration
Nominal size* Article #
NS 2NS 4NS 7NS 10
140 kg155 kg190 kg215 kg* other sizes available on request
for free standing installation in frost free areas
Installation site
93 002.50/ M193 004.50/ M193 007.50/ M193 010.50/ M1
93 002.00 / M193 004.00 / M193 007.00 / M193 010.00 / M1
Pump left Pump right
Pump size
Ø = Outer diameter b1 = Installation dimensions
2.6 kW2.6 kW2.6 kW4.0 kW
Ø
110110160160
a
1030150016002430
b
670730990990
h1
930930
11301130
h2
1000100012001200
h3
1310131015601560
l
1250181018502700
Sludge trap
200 l400 l700 l
1000 l
Wastewater content
Separator
212 l354 l567 l794 l
Grease
separator
106 l177 l302 l423 l
Nominal size
NS 2NS 4NS 7NS 10
b1
950100012201220
x
Access opening
Weight approx.
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2 123
Article descriptionIllustration
Grease separator Euro “D+S-P1” according to EN 1825NS 2/4/7/10 with direct disposal and programm controlled Shredder-Mix-System for free standing installation in frost free areas
Art. # 93 004.00 / DS-P1Version flow direction right/ inspection window as accessory
Dimensioned illustration
Nominal size* Article #
NS 2NS 4NS 7NS 10
140 kg155 kg190 kg215 kg* other sizes available on request
for free standing installation in frost free areas
Installation site
93 002.50/DS-P193 004.50/DS-P193 007.50/DS-P193 010.50/DS-P1
93 002.00/DS-P193 004.00/DS-P193 007.00/DS-P193 010.00/DS-P1
left rightDisposal pipe connection
Scope of delivery
Container with 2 domedcovers, internal and externalpiping complete with disposalpipe connection, Shredder-Mix-System with on/offswitch, inlet
Ø
110110160160
a
1030150016002430
b
670730990990
b1
1000100012201220
h1
930930
11301130
h2
1000100012001200
h3
1310131015601560
Sludge trap
200 l400 l700 l
1000 l
Wastewater content
Separator
212 l354 l567 l794 l
Grease
separator
106 l177 l302 l423 l
Nominal size
NS 2**NS 4NS 7NS 10
Access opening
l
1250181018502700
x
Ø = Outer diameter b1 = Installation dimensions
� �
bb1
�420l
a
h2 h1h3
�
�
** Please note: In the case of NS 2 the disposal pipe must be attached to the side opposite the pump.
Weight approx.
Grease separator Euro “D+S-P1” NS ...with direct disposal and programm controlled Shredder-Mix-Systemaccording to EN 1825, made of polymerFor free standing installation in frost free areas, with integrated sludge trap, domed covers made of polymer, with snap closures and sealed odour-tight, with refill inletleft/right options available (with the exception of NS 2) 1 inch,with installed suction system for disposal both from the sludgetrap and the grease separating chamber, with flange connec-tion for intake pipe, disposal flange Ø 65, PN 10 accordingto DIN 2501, Storz-B-Coupling 21/2 inch for disposal truckconnection, with high pressure cleaning system. The Shredder-Mix-System serves to simultaneously macera-te and recycle the sediment and to clean the container.Separator requires disposal vehicle for emptying. Inlet and outlet Ø ... for synthetic material pipes in: PE-HD (according to DIN 19537); PP, AS or HT according to DIN 19560.Sludge trap content: ...... Liter Manufacturer: KESSELSeparator content: ...... Liter Article #: .......................Weight: ...... kg Certification no. Z-54.1-474Delivery: System completely assembled.
On-site welding available on request.
Accessories
Page 131 - 134
124 Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Article descriptionIllustration
Grease separator Euro “D+S” according to EN 1825NS 2/4/7/10 with direct disposal and Shredder-Mix-System for free standing installation in frost free areas
Art. # 93 004.00 / DS1 Version flow direction right/ inspection window as accessory
Dimensioned illustration
Nominal size* Article #
NS 2NS 4NS 7NS 10
130 kg140 kg170 kg215 kg* other sizes available on request
for free standing installation in frost free areas
Installation site
93 002.50 / DS193 004.50 / DS193 007.50 / DS193 010.50 / DS1
93 002.00 / DS193 004.00 / DS193 007.00 / DS193 010.00 / DS1
left rightDisposal pipe connection
Scope of delivery
Container with 2 domedcovers, internal and externalpiping complete with disposalpipe connection, Shredder-Mix-System with on/offswitch, inlet
Ø
110110160160
a
1030150016002430
b
670730990990
b1
1000100012201220
h1
930930
11301130
h2
1000100012001200
h3
1310131015601560
Sludge trap
200 l400 l700 l
1000 l
Wastewater content
Separator
212 l354 l567 l794 l
Grease
separator
106 l177 l302 l423 l
Nominal size
NS 2**NS 4NS 7NS 10
Access opening
l
1250181018502700
x
Ø = Outer diameter b1 = Installation dimensions
� �
bb1
�420l
a
h2 h1h3
�
�
** Please note: In the case of NS 2 the disposal pipe must be attached to the side opposite the pump.
Weight approx.
Grease separator Euro “D+S” NS ...with direct disposal and Shredder-Mix-Systemaccording to EN 1825, made of polymerFor free standing installation in frost free areas, with integra-ted sludge trap, domed covers made of polymer, with snap closures and sealed odour-tight, with refill inletleft/right options available (with the exception of NS 2) 1 inch,with installed suction system for disposal both from the sludgetrap and the grease separating chamber, with flange connec-tion for intake pipe, disposal flange Ø 65, PN 10 accordingto DIN 2501, Storz-B-Coupling 21/2 inch for disposal truckconnection, with high pressure cleaning system. The Shredder-Mix-System serves to simultaneously macera-te and recycle the sediment and to clean the container.Separator requires disposal vehicle for emptying. Inlet and outlet Ø ... for synthetic material pipes in: PE-HD (according to DIN 19537); PP, AS or HT according toDIN 19560.Sludge trap content: ...... Liter Manufacturer: KESSELSeparator content: ...... Liter Article #: .......................Weight: ...... kg Certification no. Z-54.1-474
Delivery: System completely assembled.On-site welding available on request.
Accessories
Page 131 - 134
125Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Grease separator Euro “D” according to EN 1825NS 2/4/7/10 with direct disposal for free standing installation in frost free areas
Article descriptionIllustration
Art. # 93 002.00 / D1 Version in flow direction right
Nominal size*Article #
Disposal pipe connection
NS 2NS 4NS 7NS 10
54 kg69 kg
104 kg129 kg* other sizes available on request
for free standing installation in frost free areas
Dimensioned illustration
Installation site
b
b1
� �
Ø
110110160160
a
1030150016002430
b
670730990990
b1
840840
10801080
h1
930930
11301130
h2
1000100012001200
h3
1310131015601560
l
1250181018502700
Sludge trap
200 l400 l700 l
1000 l
Wastewater content
Separator
212 l354 l567 l794 l
Grease
separator
106 l177 l302 l423 l
Nominal size
NS 2NS 4NS 7NS 10
93 002.00 / D193 004.00 / D193 007.00 / D193 010.00 / D1
93 002.50 / D193 004.50 / D193 007.50 / D193 010.50 / D1
rightleft
Scope of delivery
Container with domed covers,piping complete with disposalpipe connection
Ø = Outer diameter b1 = Installation dimensions
420
h2 h1h3
l
a
DN/O
D
x
Access opening
Grease separator Euro “D” NS ...with direct disposal, according to EN 1825, made of polymerFor free standing installation in frost free areas,with integrated sludge trap, domed covers made of polymer,with snap closures and sealed odour-tight, with installedsuction system in flow direction left or right for disposal bothfrom the sludge trap and the grease separating chamber,with flange connection for intake pipe, disposal flange Ø 65,PN 10 according to DIN 2501, Storz-B-Coupling 21/2 inch for connection to disposal trucks.Inlet and outlet Ø ... for synthetic material pipes in: PE-HD (according to DIN 19537); PP, AS or HT according to DIN 19560.Sludge trap content: ...... Liter Manufacturer: KESSELSeparator content: ...... Liter Article #: .......................Weight: ...... kg Certification no. Z-54.1-474
Delivery: System completely assembled.On-site welding available on request.
Accessories
Page 131 - 134
Weight approx.
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2126
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2 127
Dimensioned illustration
Article descriptionIllustration
Grease separator Euro “G” according to EN 1825 NS 2/4/7/10for free standing installation in frost free areas
Art. # 93 002
Nominal size* Scope of deliveryArticle #
NS 2NS 4NS 7NS 10
50 kg65 kg
100 kg125 kg
93 00293 00493 00793 010
for free standing installation in frost free areas
Container with domed coversand snap closures
Installation site
��
b
Ø
110110160160
a
1030150016002430
b
670730990990
h1
930930
11301130
h2
1000100012001200
h3
1310131015601560
l
1250181018502700
x Sludge trap
200 l400 l700 l
1000 l
Wastewater contentAccess opening
Separator
212 l354 l567 l794 l
Grease
separator
106 l177 l302 l423 l
Nominal size
NS 2NS 4NS 7NS 10
Ø = Outer diameter
420
h1h3
h2
a
* Other sizes available on request
Weight approx.
Grease separator Euro “G” NS ...according to EN 1825, made of polymer For free standing installation in frost free areas, with integra-ted sludge trap, domed covers made of polymer,with snap closures and sealed odour-tight. Inlet and outlet Ø ... for synthetic material pipes in: PE-HD (according to DIN 19537); PP, AS or HT according to DIN 19560.Sludge trap content: ...... Liter Manufacturer: KESSELSeparator content: ...... Liter Article #: ........................Weight: ...... kg Certification no. Z-54.1-474
Delivery: System completely assembled.On-site welding available on request.
Accessories
Page 131 - 134
Retrofit set from Euro “G” to Euro “D” available on request.
Article descriptionIllustration
Grease separator SE CNS for self-disposal NS 2-25for free standing installation in frost free areas
SE CNS self disposal grease separatoraccording to EN 1825, made of High Density Polyethylene (HD-PE) For free standing installation in frost free areas, withintegrated sludge trap, quick release and odour-tightDuroplast 2K removable access cover, Ø 110 inlet / outletfor NS 2 and NS 4, Ø 160 inlet / outlet for NS 7 and NS 10,Ø 200 inlet / outlet for NS 15 and NS 20, connectionto SML pipe in accordance with DIN 19522.Separate disposal of sludge and grease with manual valves.Visual control of disposal with see-thru disposal hoses, dispo-sal possible during separator operation, includes total of 4 dis-posal buckets (2 for grease disposal / 2 for sludge disposal).With plug-in-ready control unit with operational status signal.
Technical information:Voltage: 230 V / 50 HzStart up power: 2 kWNominal current: 7 AmpProtection class: IP 54Fuse: 16 Amp.
Manufacturer: KESSEL Germany
Dimensioned illustration
Nominal size Article #
NS 2NS 4NS 7NS 10NS 15NS 20NS 25
97 kg128 kg186 kg192 kg485 kg505 kg535 kg
93 202.00 / SE1-CNS93 204.00 / SE1-CNS93 207.00 / SE1-CNS93 210.00 / SE1-CNS93 215.00 / SE1-CNS93 220.00 / SE1-CNS93 225.00 / SE1-CNS
for free standing installation in frost free areas
Installation site Scope of delivery
System completely assembled
Ø
110110160160200200200
b
930930
13001300120013001400
b1
1330133017001700165017501850
h1
1230163016301730173017301730
h2
1300170017001800180018001800
h3
1700210022002300230023002300
in liter
600 l950 l
1450 l1600 l2950 l3650 l4350 l
Total volume
Nominal size
NS 2NS 4NS 7NS 10NS 15NS 20NS 25
Access opening
l
1760183022302230360041004600
x
Ø = Outer diameter b1 = Installation dimensions
Weight in kg
h2b1
b
h1h3
l
Art. # 93 202.00 / SE1-CNS
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2128
h2h1h3
b1b
l
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2 129
Grease separator “Under sink”for free standing installation in frost free areas
Article descriptionIllustration
Ø
50
Sludge trap
7 l
Grease trap
7 l
Nominal size
NS 0.25
Storage volumes
Nominal size (l/sec.) Article #
NS 0.25 4 kg 93 025.00 / USfor free standing installation in frost free areas
Installation site Weight approx.
Grease separator “Under sink”made of polymerFor free standing installation in frost free areas,with integrated sludge trap, polyethylene quick release odour-tight covers. Inlet and outlet Ø 50.Sludge trap content: 7 LiterGrease trap content:7 Liter
Manufacturer: KESSEL Germany
Application:
Especially suitable in areas in which limited amountsof fat and sludge occur, and above all wherever vegetableoil is used.Grease separator system should be emptied on a daily basis.
KESSEL-advantages:
- System made from polymer for corrosion-free,compact structure.
- No encrustation because of smooth, wax-like surface.- Light handling of system because of low weight.- Fast removal of cover using quick release odour tight covers.- Fully adjustable inlet: 360° rotatable and vertically
adjustable inlet meets all on-site requirements.
Dimensioned illustration
350
260
290
to 4
20 296
426
790 to 930
Ø 5
0
Ø 5
0
130 Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Grease separator Euro “G” according to KESSEL Standards NS 0.25/0.5/1for free standing installation in frost free areas
Article descriptionIllustration
Grease separator Euro “G” NS....according to KESSEL Standards, made of polymerFor free standing installation in frost free areas,with integrated sludge trap, domed cover made of polymer,with snap closures and sealed odour-tight.Inlet and outlet Ø ... for synthetic material pipes in: PE-HD (according to DIN 19537); PP, HT according to DIN 19560.Sludge trap content: ... Liter Manufacturer: KESSELSeparator content: ... Liter Article #: ..........................Weight: ... kgDelivery: System completely assembled.Based on EN 1825-1 the grease separators are intended foruse under the following conditions:- Connection of a commercial dishwasher with a minimum
cycle time of 1.5 minutes- Consumption of rinsing water in a commercial dishwasher
VS = max. 5 Liter- In addition to the dishwasher, a maximum of one drainage
facility is to be connected to the dishes pre-rinse (shortterm operation)
Operating Instructions:The separated grease is to be decanted on a daily basis andemptied and cleaned once a week.
Art. # 93 025
Art. # 93 050
Art. # 93 001
Nominal size Scope of deliveryArticle #
NS 0.25NS 0.5NS 1
20 kg45 kg65 kg
93 02593 05093 001
for free standing installation in frost free areas
Container with domed cover and snap closures
Dimensioned illustration
Installation site
Ø
5050
110
Sludge trap
25 l50 l
100 l
Separator
28 l42 l75 l
Grease separator
15 l30 l60 l
Nominal size
NS 0.25NS 0.5NS 1
Ø = Outer diameter
710
570
520
510
540
710
570
520
510
1150
1200
1020
453500
990
�
�
Wastewater content
Weight approx.
131Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Article descriptionIllustration and dimensioned drawing
AccessoriesSeparator according to EN 1825 for free standing installation
Refill inlet made of polymer for separation systems
according to DIN 1988, for connection to filling and rinsing connectioncouplings of the separation systems, with two pipe clamps and attach-ment element together with pipe sealing gasket Ø 63.
Model
left 1 inchright 1 inch
Art. #
915 800
915 801
135
63
800
265
Model
Outlet vertical
Art. #
915 870
Sampling chamber Ø 400 made of polymer for separation systems
For connection to outlet pipe of separator. Inlet and outlet Ø 110/160 available options for synthetic material pipes in:PE-HD (according to DIN 19537); PVC-HT, PP or AS.Cover sealed odour-tight with snap closure.Manufacturer: KESSEL
580484
� 160� 110
� 1
10�
160
635
298
Sampling chamber Ø 400 made of polymer for separation systems
For connection to outlet pipe of separator. Inlet and outlet Ø 110/160 available options for synthetic material pipes in:PE-HD (according to DIN 19537); PVC-HT, PP or AS, drop height 120 mm.Cover sealed odour-tight with snap closure.Manufacturer: KESSEL
Model
Outlet horizontal
Art. #
915 871
575750
� 1
10�
160
120
� 1
10�
160
460
Inspection window for separation systems
Fits KESSEL Separation systems for free standing installation.In flow direction left or right with cleaning system.
Can only be retrofitted by KESSEL Customer Service (on request).
Model
in flow direction left
in flow direction right
Art. #
917 770
917 771
154
48
308
R154
1 inch threaded connection
Art. #
917 821
SonicControl level sensing systemwith ultra sonic sensor for grease separators
Accurate monitoring and data transfer of grease levels. 230 V - 50 Hz power connection. With battery back up, connection forremote speaker.Insallation set with easy assembly and maintenance. For use on aboveground or below ground separators. For retrofit use on existing separators.Control unit with optical and audible alarm with potential free contact.Electronic log book with 12 month capacity. Data transfer by telemetry.
Voltage: 230 V ~ 50 Hz Protection: IP 54Plug: Schuko (double pole)Cable length: 5 m (extendable on-site to 30 meters)
Article descriptionIllustration and dimensioned drawing
AccessoriesSeparator according to EN 1825 for free standing installation
Art. #
917 414
Art. #
917 413
Stainless steel access panel
For recessed wall installationwith Storz-B disposal pipe hook up connection and remote control for use with fully automated grease separators.Dimensions: 640 x 440 x 160 mm (Width x Height x Depth)Model: “Recessed”, 2 doors, lockable
Stainless steel access panel
For wall installationwith Storz-B disposal pipe hook-up connection and remote control for use with fully automated grease separators.Dimensions: 600 x 400 x 160 mm (Width x Height x Depth)Model: “Wall installation”, 2 doors, lockable
640600
440
400
160
Remote Control
Storz-B-Coupling
600
400
160
Remote Control
Storz-B-Coupling
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2132
Model
-
Art. #
916 601
Remote control
Fits KESSEL Separation systems for free standing installationModel “E+S” program-controlled, fully automated according to EN 1825.Cable length 10 m.
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2 133
Art. # Ø*Article descriptionIllustration and dimensioned drawing
Twin lifting station
made of polymer for above ground installation
With twin removable pumps, integrated backwater flap, Pressure diaphragm control. Inlet Ø 110, ventilation connection Ø 75 (incl. pipe sealing gasket), control with potential free contact.Pressure connection: 11/2 inch outer thread or pressure pipe Ø 40 mm for PVC glued connection.Inlet height: 530 mmTotal height: 720 mm, Ø 450 mmVoltage: 230 V ~ 50 HzMax. container size: 55 lmax. pumping height: 8 mIntake power: 2 x 0.5 kWPower cable: 5 mWeight: approx. 25 kg
Ø 40 28 541
AccessoriesSeparator according to EN 1825 for free standing installation
* Ø = Outer Diameter
guaranteed with
tested quality
Type-testedand monitored
LGA Certification: Z-53.3-310EN 12050-2500
Ø 110
530
Ø 4
025
857
5 720
Optional:Potential-free contact and audible alarm page 49
Performance diagrampage 47
Ecolift ® wastewater lifting system for pipes with natural gradient to the sewer
The alternative to a classical lifting station
For wastewater with or without sewage, for installation in an exposed wastewater pipe
With protective cover. With integrated pump and abackwater valve locked by a motor. During normal conditions, the pipe cross section is open, in the caseof backwater the valve is closed and locked completelyautomatically. During the backwater period, soiledwater is drained using a pump with chopping device,via a pressure pipe over the backwater level. Plug-incontrol and warning unit with display, self-diagnosissystem (SDS) and battery buffering for maximumsafety, with logbook (diary function) for reading out the past operating states.
Power cable / cable length: 5 mMains voltage/frequency: 230 V AC / 50 HzProtective rating: IP 54 (switch unit)Protective rating: IP 68 (motor)
Ø 110 L: 642 mm H: 405 mmØ 125 L: 645 mm H: 405 mmØ 160 L: 656 mm H: 405 mmØ 200 L: 720 mm H: 405 mm
21 100
21 125
21 150
21 200
Ø 110
Ø 125
Ø 160
Ø 200
9
H
Ø
L
Ø 40
Approval: pending
Further information: See lifting stations, page 38.
134 Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Further information: See lifting stations, page 44/45.
Article descriptionIllustration and dimensioned drawing
Lifting station Aqualift ® F DuoTwin station
for wastewater with or without sewagefor separation systemsConsisting of:Polyethylene storage chamber, chamber volumeapprox. 120 liters, pumping volume approx. 50 liters,with air pressure level detector, clean-out opening.Connection for inlet Ø 110 (inlet height 300 mm) andventilation Ø 75, connection coupling for manualdiaphragm pump Ø 32.Twin wastewater pump with non-chokable impellerto pump wastewater with or without sewage (openchannel passage 40 mm). Pump is rated submersible(IP 68), power cable length 5 m. Horizontal outlet with integrated non-return valve,connection coupling Ø 110 with hose section,with closure valve (provided loose)Electric control unit for fully automated pumpoperation, control unit is splash proof (IP 65),wall mounted, voltage 400 V DS at 50 Hz. With potential-free contact.Total weight approx. 84 kg.
AccessoriesSeparator according to EN 1825 for free standing installation
1.1 kW
2.2 kW
400 V
400 V
28 659
28 631
With closure valve with horizontal pressure outlet:
773
780
160
788
590
�32
�110�75
�
Inle
t hei
ght
300
EN 12050-1
Art. #Power Currentconnection
Lifting station Aqualift ® F Duo XXLtwin lifting station with closure valve
for wastewater with or without sewage(For use with grease separators size NS 10 and larger)for free standing installation in frost free areasConsists of:Polyethylene collection chambers,storage volume 750 liter, pumping volume 300 liter,pneumatic level control, twin 420 mm OD access /maintenance covers, Ø 160 inlet (Ø 200 availableupon request), inlet height 1055 mm, ventilation con-nection size Ø 110.Twin wastewater pumps with macerating (cuttingassembly) for pumping wastewater with or without raw sewage, IP 68 submersible pumps, Duty / Standbyoperation, 5 meter power cable length. Vertical pressure outlet with Ø 110 connection andflange, with closure valve and integrated backflow preventer.Electrical control for fully automated pump control, IP 54 splash proof control unit housing, for wall mounting, operational voltage - 400 V DS, with potential free contact (BMS) connections).Total weight empty: approx 220 kg
EN 12050-118372000
1385
1296
985
1055
2.6 kW
3.5 kW
4.8 kW
400 V
400 V
400 V
28 638
28 639
28 640
Further information: See lifting stations, page 50.
* Ø = Outer Diameter
135Catalogue 2.2
Grease separators for underground installation
PPoollyy
eetthhyy
lleennee WWaarrrraannttyy
202 YeY ars
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Illustration
Grease separator Euro “G” NS ...according to EN 1825, made of polymer for underground installation, installation depth D = ..................... mm,with integrated sludge trap, upper section made of polymer, continuous height and level adjustment, can be tilted up to 5°, sealed odour-tight with cover Class B, D according to EN 124 in cast iron, incl. removal mechanism, certifiedstatics.Inlet and outlet Ø 110 for synthetic material pipes in: PE-HD (according to DIN 19537); PVC (according to DIN V19534); PP or AS.Sludge trap content:...... Liter Manufacturer: KESSELSeparator content: ...... Liter Article #: .........................Weight: ...... kg Certification no. Z-54.1-440
Delivery: System completely assembled.
Handles groundwater depths up to 500 mm
Accessories
Page 138 - 139
Nominal size Installation depth D
NS 1NS 2NS 4
111 kg120 kg130 kg
550 to 950 mm550 to 950 mm550 to 950 mm
for underground installation frost free depth 800 mm(Type 80)
Dimensioned illustration
Installation site Art. # Class B Art. # Class D
93 001/80 B93 002/80 B93 004/80 B
93 001/80 D93 002/80 D93 004/80 D
NS 1NS 2NS 4
111 kg120 kg130 kg
800 to 1200 mm800 to 1200 mm800 to 1200 mm
for underground installation frost free depth 1200 mm(Type 120)
93 001/120 B93 002/120 B93 004/120 B
93 001/120 D93 002/120 D93 004/120 D
Nominal size
NS 1NS 2NS 4
Ø
110110110
a
138013801380
b
110611061106
h*
105013001550
h1
540790
1040
h2
610860
1110
Sludge trap
140 l200 l400 l
Wastewater content
Separator
230 l370 l370 l
Grease
separator
70 l120 l160 l
b
a
� 875
h
� 610
�
h2 h1
�
D = Installation depth Ø = Outer diameter
Other installation depths available on request
Grease separator Euro “G”according EN 1825 NS 1/2/4for underground installation
Variable upper section:
inclinableheight adjustableby 100 to 550 mm
* Details apply for Type 80. For Type 120 h* = h + 250 mm applies.
Art. # 93004/120D + 915880D
Article description
Inle
tD
Outle
t
Weight approx.
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2136
Nominal size Installation depth D
Illustration
Art. # 93 020/120 B and 915 880 B-200
NS 7NS 10NS 15NS 20NS 25NS 30NS 35
305 kg360 kg455 kg530 kg570 kg570 kg570 kg
760 to 1260 mm760 to 1260 mm760 to 1260 mm760 to 1260 mm880 to 1380 mm880 to 1380 mm880 to 1380 mm
for underground installation frost free depthMinimum installation depth canbe achieved by cutting off theupper section
BL
h1h2
� �
Dimensioned illustration
Installation site Art. # Class B Art. # Class D
93 007/120 B93 010/120 B93 015/120 B93 020/120 B93 925/120 B93 930/120 B93 935/120 B
93 007/120 D93 010/120D93 015/120D93 020/120 D93 925/120 D93 930/120 D93 935/120 D
Nominal size
NS 7NS 10NS 15NS 20NS 25NS 30NS 35
Ø
160160200200200250250
L
2080286023003060374037403740
B
1200120017601760201020102010
h1
1030103015601560155015501700
h2
1100110016301630165016501800
Sludge trap
700 l1000 l1500 l2000 l2500 l3000 l3500 l
Wastewater content
Separator
1100 l1600 l2800 l3800 l5300 l4800 l4800 l
Grease
separator
280 l400 l600 l800 l
2000 l2000 l2000 l
D = Installation depth Ø = Outer diameter
**DEC = Depth of earth coverageClass D = 700 mm ≤ DEC ≤ 1500 mmClass B = 700 mm ≤ DEC ≤ 1800 mm
Ø 160: D-DEC = 155 mmØ 200: D-DEC = 180 mm
Ø 200: D-DEC = 480 mmØ 250: D-DEC = 330 mm
NS 7/10/15/20:
NS 25/30/35:
Grease separator Euro “G” NS ...according to EN 1825, made of polymerfor underground installation, installation depth D = ......................mm,with integrated sludge trap, upper sections made of polymer,continuous height and level adjustment, can be tilted up to 5°,closed odour-tight with covers Class B, D according to EN 124in cast iron, incl. removal mechanism, Private vehicle trafficproof (Depth of earth coverage DEC 700 to 1800 mm),Traffic proof for heavy duty vehicles (depth of earth coverageDEC 700 to 1500 mm and additional concrete slab providedon-site), certified statics.Inlet and outlet Ø ... for synthetic material pipes in: PE-HD (according to DIN 19537); PVC (according to DIN V19534); PP or AS.Installation in groundwater is possible, if groundwater level isnot higher than outlet pipe base.Sludge trap content:...... Liter Manufacturer: KESSELSeparator content: ...... Liter Article #: ..........................Weight: ...... kg Certification no. Z-54.1-440
Delivery: System completely assembled.
Accessories
Page 138 - 139
Grease separator Euro “G”according EN 1825 NS 7/10/15/20/25/30/35for underground installation
Variable upper section:
inclinableheight adjustable by 100 to 550 mm
Article description
D DEC*
*
Weight approx.
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2 137
138 Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Article descriptionIllustration and dimensioned drawing
fits separator
NS 1, NS 2 and NS 4NS 7 and NS 10
NS 15, NS 20 andcustom-made
Installationdepth D (mm)
* 400-1300
* 400-1300
Inlet/outletØ
110/160200
Sampling chamber Ø 400 made of polymerfor separation systems, for underground installation
For connection to outlet pipe of separator. For installation depth D = ...... .Inlet and outlet Ø 110/160 available options Ø 200 for synthetic materialpipes in: PE-HD (according to DIN 19537); PVC (according to DIN V19534);PP or AS. Sampling chamber middle diameter 400 mm, telescopic uppersection with clamping ring, cover Class A/B/D, screwed down odour-tight,drop height 120 mm.
Extension by 600 mm with extension section Art. # 915 402
575750
120
50-4
00
70
100
� 1
60�
110
900
� 1
10�
160
Installationdepth D (mm)
1180-16301180-16301180-1630
Outlet
Ø 110Ø 160Ø 200
Art. # Class DClass B
915 10 10 B
915 10 15 B
915 10 20 B
915 10 10 D
915 10 15 D
915 10 20 D
Sampling chamber Ø 1000 mmin polyethylene synthetic material,for separation systems, for underground installation
Inlet and outlet Ø ... for synthetic material pipes in: PE-HD (according to DIN 19537); PVC (according to DIN V19534); PP or AS.Installation depth D ..... mm, in monolithic structure, water-tight, resistantto aggressive wastewater, with integrated access steps, with telescopicallyheight-adjustable upper section made of polymer, sealed odour-tight withcover Class B/D according to EN 124 in cast iron, incl. removal mechanism.Drop height 160 mm.
160
� �
1200
100-
550
Inlet/
Art. # Class D
915 880 D
915 880 D-200
Class B
915 880 B
915 880 B-200
Class A
915 880 A
915 880 A-200
* Minimum installation depth can be achieved by cutting off
Other installation depths available on request
Extension section
For deep installationExtension height max. 600 mm (can be reduced).
Model
Extension height = 600 mm
Art. #
915 402
Extension section made of polymerfor separation systems
Fits all KESSEL Separation systems for underground installation,extension height 510 mm / 1010 mm; incl. gasket
smaller/larger extension sections available on request
Model
Extension height = 510 mm
Extension height = 1010 mm
Art. #
917 406
917 407
600
�660
�630�806
�686
�740
116
15
628
20°
AccessoriesSeparator according to EN 1825 for underground installation
D
D
139Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Article descriptionIllustration and dimensioned drawing
AccessoriesSeparator according to EN 1825 for underground installation
Art. #
917 821
SonicControl level sensing systemwith ultra sonic sensor for grease separators
Accurate monitoring and data transfer of grease levels. 230 V - 50 Hz power connection. With battery back up, connection forremote speaker.Insallation set with easy assembly and maintenance. For use on aboveground or below ground separators. For retrofit use on existing separators.Control unit with optical and audible alarm with potential free contact.Electronic log book with 12 month capacity. Data transfer by telemetry.
Voltage: 230 V ~ 50 Hz; Protection: IP 54;Plug: Schuko (double pole);Cable length: 5 m (extendable on-site to 30 meters).
Art. #
917 822
AccessoriesAudible alarm Art. # 20 162,25 m cable extension available upon request.PE-HD conduit entrance connection (for conduit connection to underground separators)
Underground lifting stations for use after grease separatorscan be seen in the lifting station sectionpage 54 - 57.
Art. #
917 414
Art. #
917 413
Stainless steel access panel
For recessed wall installationwith Storz-B disposal pipe hook up connection and remote control for use with fully automated grease separators.Dimensions: 640 x 440 x 160 mm (Width x Height x Depth)Model: “Recessed”, 2 doors, lockable
Stainless steel access panel
For wall installationwith Storz-B disposal pipe hook-up connection and remote control for use with fully automated grease separators.Dimensions: 600 x 400 x 160 mm (Width x Height x Depth)Model: “Wall installation”, 2 doors, lockable
640600
440
400
160
Remote Control
Storz-B-Coupling
600
400
160
Remote Control
Storz-B-Coupling
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2140
141Catalogue 2.2
Oil-/Fuel separators Coalescence separators
PPoollyy
eetthhyy
lleennee WWaarrrraannttyy
202 YeY ars
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
- typical advantagesOil-/Fuel separators
Coalescence separators
SonicControl
142 Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
In addition to the legally required guarantee,
KESSEL offers a 20 year guarantee on the
separator body and upper sections. This
guarantee covers leak-proofness, general
usability and structural soundness of the parts.
Poly
et
hylene Warranty
Poly
et
hylene Warranty
20 Years
The German Institute for Structural Engineering (DIBt) has granted site-inspection certification for oil, fuel and coalescence separators made of polymer. KESSEL is therefore the first manufacturer on the German market to be granted such an inspection certificate.
“The polyethylene material creates significant advantages
for planners, decision makers and processing workers,
such as long-lasting water-tightness, the relative low
weight, short installation times and last but not least an
attractive price.”
Our coalescence separators
are certified for bio-diesel use
Guaranteed leak tight system
Watertight gasketed connection between upper section andseparator assure that environmentally damaging fuel doesnot enter earth / groundwater supply
Vertically adjustable
upper sections standard
with separator
Included upper sections allowon-site vertical adjustability ofup to 500 mm and a lateral til-ting of up to 5°. The odour tightmanhole covers are available inload classes A/B and D.
Product see page 147
Products see pages 143 - 146
SonicControlautomated fuel level measuring system Monitoring and notification of oil and sludge layer thickness andback-up / overflow warning
According to Euronorm EN 858-1, fuel separator must be equippedwith automated warning systems. The KESSEL SonicControl systemfor fuel / coalescence separators offers reliable and accurate mo-nitoring of the fuel level, sludge height and back-up / flood levels.
Oil layer thickness (d1)
Sludge layer thickness (d2)
Control value (r1)
Control value (r2)
Measuredvalue(m2)
Measuredvalue(m1)
Three warning features in one system
- cm accurate monitoring of the fuel layer- cm accurate monitoring of the sludge layer- back-up / overflow warning
Operation via control unit
USB connection for downloading logbook
Quick and easy installation
For use with all KESSEL oil and coalescence separators
Retro-fitting of existing separators
Read out software
Oil layer thickness (d1) = [Control value (r1) - Measured value (m1)] x 1,2
Sludge layer thickness (d2) = Control value (r2) - Measured value (m2)
143Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Dimensioned illustration
L
h2 h1
B
� �
Class D = 700 mm � DEC � 1500 mmClass B = 700 mm � DEC � 1800 mm
Ø 160: D-DEC = 155 mmØ 200: D-DEC = 180 mm
**DEC = Depth of earth coverage
1) Comparable sludge trap total volume in accordance with the dimensioning according to EN 858. 2) eccentric reduction inlet/outlet to Ø 160 possible on-site, as a consequence the sampling chamber 915880 A/B/D can be used see page 138.
Coalescence separator
according to EN 858, made of polymerfor underground installation, installation depth D =...................... mmWith integrated sludge trap and self-actuated closure lock, calibrated for light liquid with densities between 0.85 to 0.95 g/cm3.With removable coalescence filter.Upper sections made of polymer, continuous height and leveladjustment, tiltable to 5°, with covers Class B, D according to EN 124 in cast iron, including removal mecha-nism, private vehicle traffic proof (depth of earth coverage DEC 700 to 1800 mm), traffic proof for heavy dutyvehicles (depth of earth coverage DEC 700 to 1500 mm andadditional concrete slab provided on-site), certified statics, Inlet and outlet Ø ... for synthetic material pipes in: PE-HD (according to DIN 19537); PVC pipe (according to DIN V19534); PP or AS.Sludge trap content ............. Liter Manufacturer: KESSELTotal capacity ............. Liter Art. # .................max. oil storage volume ............. Liter Certification no.Weight ............. kg Z-54.3-454
Accessories
Sampling chamber for underground installation see page 138. Extension section for deep installation see page 138.Alarm units for when the maximum oil level is reached and there is a back-up of water (required according to EN 858) see page 148.Oil and sludge suction system see page 147.
Illustration
Coalescence separator NS 3 - NS 15 according to EN 858, Class Ifor underground installation with DIBt-Certification
Art. # 99 710.80 D
Also suitable for filling
stations with high-perfor-
mance filling pumps
Variable upper section:
inclinable
Article description
D DEC*
*
height adjustable all vehicle traffic proof
Weightin kg
Art. # Cover
Class D
Art. # Cover
Class B
99 503.10D
99 706.30D
99 706.80D
99 710.15D
99 710.30D
99 710.80D
99 715.80D
99 503.10B
99 706.30B
99 706.80B
99 710.15B
99 710.30B
99 710.80B
99 715.80B
Oil storagecapacityin Liter
187265380262265380380
395535610440535610610
Totalcapacityin Liter
1800430058002600430058005800
h1 inmm
1040156015601040156015601560
h2 inmm
1100163016301100163016301630
B inmm
1200176017601200176017601760
L inmm
2080230030602860230030603060
Ø*
160200200160200200200
Sludge trapcapacityin Liter
1000250050001500250050005000
1)
1)
NS
3
6
6
10
10
10
15
D in mmmin max
830850870830850870870
1240123012501240123012501250
2)
2)
2)
2)
* Ø =
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2144
Illustration and dimensioned drawing
Coalescence separator NS 3/6 according to EN 858, Class Ifor underground installation
Article description
Variable upper section:
inclinableheight adjustable all vehicle traffic proof
Coalescence separator Class I Ø 1000
according to EN 858, made of polyethylenefor underground installation, installation depth D from 565 to 1015 mmWith integrated sludge trap and self-actuated closure lock, calibrated for light liquid with densities between 0.85 to 0.95 g/cm3.With removable coalescence filter insert.Completely water tight to top of cover, resistant againstaggressive wastewaters. Vertically adjustable polymer uppersection, tiltable to 5°, cast iron manhole cover according to EN 124, load class: D, with removal key, certified structural test.Inlet and outlet Ø ..... for synthetic material pipes in: PE-HD (according to DIN 19537); PVC pipe (according to DIN V19534); PP or AS.Sludge trap content ............. Liter Manufacturer: KESSELTotal capacity ............. Liter Art. # .................max. oil storage volume ............. Liter Weight ............. kg Delivery: Completely assembled.
Not for installation in high groundwater areas !
Art. # 99 703.10B
�
Dmin
/ Dm
axh2 h1
� 1
10
NS 3 Coalescence separator with 1600 liter sludge trap
Due to hydraulically optimized design,KESSEL separators do not require the standard primary sludge trap.
Advantages:
1. Reduced cost and separator size.2. Lower disposal costs.
Standard type separator
Total volume 2000 literKESSEL Separator
Total volume 1200 liter
200 liter
200 liter
800 liter
800 liter
Oil / fuel layer
Clear water zone for oil / fuel separation
Clear water zone for sludge separation
Disposal volume = max. 50%
of total sludge volume
Oil / fuel layer
Clear water zone for oil / fuel separation
Disposal volume sludge
200 liter
200 liter
800 liter
Sludge trap capacity 1600 liter�
3
3
6 1)
NS
400
800
500
Sludge disposalvolume in liter
800
1600
1000
Sludge trapcapacity in liter
110
110
160
1100
1100
1100
Ø* Ø**
545
545
560
1105
1605
1090
1055
1555
1020
h2 (Inlet bottom) in mm
h1 (Outlet bottom) in mm
200
200
200
Oil storagecapacity in liter
175
190
305
205
220
338
99 703.04D
99 703.10D
99 706.10D
995
995
1010
min maxD
Weight in kgB/D
Art. #cover
Class D
99 703.04B
99 703.10B
99 706.10B
Art. #cover
Class B
1) = Twin-chamber system * Ø = Inlet /Outlet ** Ø = Outer Diameter of chamber
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2 145
Oil/fuel separator NS 3 - NS 15according to EN 858, Class IIfor underground installation
Illustration
Variable upper section:
inclinable
Art. # 99 610.80Art. # 99 610.80 D
Dimensioned illustration
L
h2 h1
B
� �
Class D = 700 mm � DEC � 1500 mmClass B = 700 mm � DEC � 1800 mm
**DEC = Depth of earth coverage
1) Comparable sludge trap total volume in accordance with the dimensioning according to EN 858-2. 2) eccentric reduction inlet/outlet to Ø 160 possible on-site, as a consequence the sampling chamber 915880 A/B/D can be used see page 138.
Weightin kg
Art. # Cover
Class D
Art. # Cover
Class B
99 403.10D
99 606.30D
99 606.80D
99 610.15D
99 610.30D
99 610.80D
99 615.80D
99 403.10B
99 606.30B
99 606.80B
99 610.15B
99 610.30B
99 610.80B
99 615.80B
Oil storagecapacityin Liter
187265380262265380380
379519594424519594594
Totalcapacityin Liter
1800430058002600430058005800
h1 inmm
1040156015601040156015601560
h2 inmm
1100163016301100163016301630
B inmm
1200176017601200176017601760
L inmm
2080230030602860230030603060
Ø*
160200200160200200200
Sludge trapcapacityin Liter
1000250050001500250050005000
1)
1)
NS
3
6
6
10
10
10
15
D in mmmin max
830850870830850870870
1240123012501240123012501250
Ø 160: D-DEC = 155 mmØ 200: D-DEC = 180 mm
2)
2)
2)
Also suitable for filling
stations with high-perfor-
mance filling pumps
Article description
height adjustable by 100 to 550 mmall vehicle traffic proof
D DEC*
*
Oil/fuel separator
according to EN 858, made of polymerfor underground installation, installation depth D =...................... mmWith integrated sludge trap and self-actuated closure lock, calibrated for light liquid with densities between 0.85 to 0.95 g/cm3.Upper sections made of polymer, continuous height and leveladjustment, tiltable up to 5°, with covers Class B, D accordingto EN 124 in cast iron, incl. removal mechanism, private vehi-cle traffic proof (depth of earth coverage DEC 700 to 1800 mm),traffic proof for heavy duty vehicles (depth of earth coverageDEC 700 to 1500 mm and additional concrete slab providedon-site), certified statics, Inlet and outlet Ø ... for synthetic material pipes in: PE-HD (according to DIN 19537);PVC pipe (according to DIN V19534); PP or AS.Sludge trap content ............. Liter Manufacturer: KESSELTotal capacity ............. Liter Art. # .................max. oil storage volume ............. Liter Certification no.Weight ............. kg Z-54.2-453
Accessories
Sampling chamber for underground installation see page 138. Extension section for deep installation see page 138.Alarm units when the maximum oil level is reached and there is a back-up of water (required according to EN 858) see page 148.Oil and sludge suction system see page 147.Coalescence filter insert for retrofitting to the coalescenceseparator see page 147.
* Ø = Outer Diameter
Art. # 99 601.002B
�
L
h2 h1
Oil/fuel separator NS 1.5according to KESSEL Standardfor underground installation
Illustration and dimensioned drawing
Oil/fuel separator Class II Ø 1000
according to KESSEL Standardfor underground installation, installation depth D = ...................... mm.With integrated sludge trap and self-actuated closure lock, calibrated for light liquid with densities between 0.85 to 0.95 g/cm3.Optional with backwater flap valve according to DIN 13564Upper sections made of polymer, continuous height and leveladjustment, cover Class A/B.Inlet and outlet Ø 110 for synthetic material pipes in: PE-HD (according to DIN 19537); PVC pipe (according to DIN V19534); PP or AS.
Accessories
Sampling chamber for underground installation see page 138.Alarm unit when the maximum oil level is reached and thereis a back-up of water (required according to EN 858) see page 148.
Oil/fuel separator Class II Ø 800
according to KESSEL Standardfor underground installation, installation depth D = ...................... mm.With integrated sludge trap and self-actuated closure lock, calibrated for light liquid with densities between 0.85 to 0.95 g/cm3.Optional with backwater flap valve according to DIN 13564Upper sections made of polymer, continuous height and leveladjustment, cover Class A/B.Inlet and outlet Ø 110 for synthetic material pipes in: PE-HD (according to DIN 19537); PVC pipe (according to DIN V19534); PP or AS.
Accessories
Sampling chamber for underground installation see page 138.Alarm unit when the maximum oil level is reached and thereis a back-up of water (required according to EN 858) see page 148.Art. # 99 601.016B/D
�
L
h2 h1
Øchamber
400
800
1000
Sludge trap
capacity
17 l
130 l
360 l
Qmax.
in l/s
1.5
1.5
1.5
Ø
110
110
110
L
582
1091
1425
B
520
1012
1300
min
231
518
570
h2 (Inlet
bottom)
389 mm
508 mm
630 mm
h1 (Outlet
bottom)
342 mm
461 mm
583 mm
Oil storage
capacity
17.6 l
70.5 l
110 l
Excess
level
50
50
70
Weight
in kg
12
74
110
Art. #
Class B
99 601.002B
99 601.016B
99 601.041B
max
324
942
995
NS
1.5
1.5
1.5
D
Art. # 99 601.041B/D�
L
h2 h1
Application: Diesel filling station
Application: Small workshop
Application: Private washing area
rotatableVariable upper section:
inclinableheight adjustablePrivate vehicle proof
Article description
D
D
D
Oil/fuel separator Class II Ø 400
according to KESSEL Standardfor underground installation, installation depth D = ...................... mm.With integrated small sludge trap and self-actuated closurelock, calibrated for light liquid with densities between 0.85 to 0.95 g/cm3.Optional with backwater flap valve according to DIN 13564Upper sections made of polymer, continuous height and leveladjustment, cover Class A/B.Inlet and outlet Ø 110 for synthetic material pipes in: PE-HD (according to DIN 19537); PVC pipe (according to DIN V19534); PP or AS.
Accessories
Sampling chamber for underground installation see page 138.
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2146
Class D
-
99 601.016D
99 601.041D
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Gre
as
e s
ep
ara
tors
fo
r u
nd
erg
rou
nd
in
sta
lla
tio
nG
rea
se
se
pa
rato
rs f
or
inte
rio
r in
sta
lla
tio
n
Catalogue 2.2 147
Oil suction system
Intake pipe elbow Ø 50 mm 0.5 m Intake hose Ø i 50 mm for individually tailoring to suit the upper section in NBR with steel wire spiral and Cu strands and connected Storzintake coupling 52 C and identification label.
Sludge extraction system
Intake pipe Ø 50 mm with sludge extraction funnel0.5 m Intake hose Ø i 50 mm for individually tailoring to suit the upper section in NBR with steel wire spiral and Cu strands and connected Storzintake coupling 52 C and identification label.
for inlet
Art. #
Ø 200
917 808
for inlet
Art. #
Ø 160
917 803
for inlet
Art. #
Ø 200
917 809
for inlet
Art. #
Ø 160
917 804
Cable extension for alarm units (per meter)
Art. #
917 810
Article descriptionIllustration and dimensioned drawing
AccessoriesSeparator for underground installation
SonicControl automated level measuring system with ultrasound sensor for oil / coalescence separators
SonicControl OSAMonitoring and notification of oiland sludge layer thicknessand back-up / overflow warning.
SonicControl OSMonitoring and notification of oiland sludge layer thickness
SonicControl OAMonitoring and notificationof oil layer thicknessand back-up / overflow warning.
SonicControl SAMonitoring and notificationof sludge layer thicknessand back-up / overflow warning.
With power chord, battery buffer system and connection for remote signalling device
Voltage: 230 V ~ 50 Hz; Protection type: IP 54;Plug: Schuko 2-polig;Cable length: 30 m
Available from mid 2011
Art. #
917 824
Art. #
917 825
Art. #
917 826
Art. #
917 827
Illustration shows Art. # 917 824
Coalescence filter insert
for retrofitting the KESSEL Oil/fuel separator NS 3-NS 15 to coalescence separator
Art. #
917 805
Coalescence filter
for KESSEL coalescence separator Class I Ø 1000
Art. #
917 816
148 Catalogue 2.2
Gre
as
e s
ep
ara
tors
fo
r in
teri
or
ins
tall
ati
on
G
rea
se
se
pa
rato
rs f
or
un
de
rgro
un
d i
ns
tall
ati
on
Oil
-/F
ue
l-/C
oa
les
ce
nc
e s
ep
ara
tors
Article descriptionIllustration and dimensioned drawing
AccessoriesSeparator for underground installation
Art. #
917 414
Art. #
917 413
Stainless steel access panel
For recessed wall installationwith Storz-B disposal pipe hook up connection and remote control for use with fully automated grease separators.Dimensions: 600 x 440 x 160 mm (Width x Height x Depth)Model: “Recessed”, 2 doors, lockable
Stainless steel access panel
For wall installationwith Storz-B disposal pipe hook-up connection and remote control for use with fully automated grease separators.Dimensions: 600 x 400 x 160 mm (Width x Height x Depth)Model: “Wall installation”, 2 doors, lockable
640600
440
400
160
Remote Control
Storz-B-Coupling
600
400
160
Remote Control
Storz-B-Coupling
Alarm unit set
Alarm unit for monitoring oil level (see Art. # 917801) andfor indicating limit level (see Art. # 917802).
Alarm unit for limit level display (Detecting a back-up of water in the light liquid separator)
Limit level probe suitable for Ex-Zone 0 with 5 m connection cable (up to max.200 m extendible), Attachment set for convenient assembly and maintenance(probe can thus be reached from the top), water-tight cable connection forextending the connection cable, through-going pipe with screw closure, twocable screw-connections, housing for wall assembly IP 65, control unit withoptical and acoustic alarm with potential-free contact, with sensor self-moni-toring and repeat alarm.
Art. #
917 806
Art. #
917 802
Alarm unit for monitoring oil level (Detecting the layer thickness in the oil and light liquid separators)Oil level probe suitable for Ex-Zone 0 with 5 m connection cable (up to max.200 m extendible), Attachment set for convenient assembly and maintenance(probe can thus be reached from the top), water-tight cable connection forextending the connection cable, through-going pipe with screw closure andtwo cable screw-connections, housing for wall assembly IP 65, control unitwith optical and acoustic alarm with potential-free contact, with sensor self-monitoring and repeat alarm.
Art. #
917 801