07 gaseous fuels
TRANSCRIPT
-
8/13/2019 07 Gaseous Fuels
1/50
1
Gaseous Fuels
-
8/13/2019 07 Gaseous Fuels
2/50
2
1. Introduction
There are numerous factors which need to be
taken into account when selecting a fuel for
any give application.
Economics is the overriding consideration-thecapital cost of the combustion equipment
together with the running costs, which are
fuel purchasing and maintenance.
-
8/13/2019 07 Gaseous Fuels
3/50
3
2. Natural Gas
Natural gas is obtained from deposits in
sedimentary rock formations which are also
sources of oil.
It is extracted from production fields andpiped (at approximately 90 bar) to a
processing plant where condensable
hydrocarbons are extracted from the rawproduct.
-
8/13/2019 07 Gaseous Fuels
4/50
4
It is then distributed in a high-pressure mains
system.
Pressure losses are made up by intermediate
booster stations and the pressure is droppedto around 2500 Pa in governor installations
where gas is taken from the mains and enters
local distribution networks.
-
8/13/2019 07 Gaseous Fuels
5/50
5
The initial processing, compression and
heating at governor installations uses the gas
as an energy source.
The energy overhead of the winning anddistribution of a natural gas is about 6% of
the extracted calorific value.
-
8/13/2019 07 Gaseous Fuels
6/50
6
The composition of a natural gas will vary
according to where it was extracted from, but
the principal constituent is always methane.
There are generally small quantities of higherhydrocarbons together with around 1% by
volume of inert gas (mostly nitrogen).
-
8/13/2019 07 Gaseous Fuels
7/50
7
The characteristics of a typical natural gas are:
Composition (% vol) CH4 92
other HC 5
inert gases 3Density (kg/m3) 0.7
Gross calorific value (MJ/m3) 41
-
8/13/2019 07 Gaseous Fuels
8/50
8
3. Town gas (Coal Gas)
The original source of the gas which was
distributed to towns and cities by supply
utilities was from the gasification of coal.
The process consisted of burning a suitablegrade of coal in a bed with a carefully
controlled air supply (and steam injection) to
produce gas and also coke.
-
8/13/2019 07 Gaseous Fuels
9/50
9
This is still the gas supplied by utility
companies in many parts of the world and
there is continuing longer-term development
of coal gasification, since it is one of the mostlikely ways of exploiting the substantial world
reserves of solid fuel.
It was first introduced into the UK and theUSA at the beginning of the 19th century.
-
8/13/2019 07 Gaseous Fuels
10/50
10
The gas was produced by heating the raw
coal in the absence of air to drive off the
volatile products.
This was essentially a two-stage process,with the carbon in the coal being initially
oxidized to carbon dioxide, followed by a
reduction to carbon monoxide:C + O2CO2
CO2+ C2CO
-
8/13/2019 07 Gaseous Fuels
11/50
11
The volatile constituents from the coal were
also present, hence the gas contained some
methane and hydrogen from this source.
An improved product was obtained if waterwas admitted to the reacting mixture, the
water being reduced in the so-called water
gas shift reaction:C + H2O CO + H2
-
8/13/2019 07 Gaseous Fuels
12/50
12
This gas was produced by a cyclic process wherethe reacting bed was alternately blown with air andsteam- the former exhibiting an exothermic, and thelatter an endothermic, reaction.
A typical town gas produced by this process has thefollowing properties:Composition (% vol) H2 48
CO 5
CH4 34CO2 13Density (kg/m3) 0.6Gross calorific value (MJ/m3) 20.2
-
8/13/2019 07 Gaseous Fuels
13/50
13
A more recent gasification process,
developed since 1936, is the Lurgi gasifier.
In this process the reaction vessel is
pressurized, and oxygen (as opposed to air)as well as steam is injected into the hot bed.
The products of this stage of the reaction are
principally carbon monoxide and hydrogen.
-
8/13/2019 07 Gaseous Fuels
14/50
14
Further reaction to methane is promoted by a nickel
catalyst at temperatures of about 250-350:
CO + 3H2CH4+ H2O
The sulfur present in the coal can be removed bythe presence of limestone as follows:
H2+ S H2S
H2S + CaCO3CaS +H2O +CO2
-
8/13/2019 07 Gaseous Fuels
15/50
15
4. Liquefied Petroleum Gas (LPG)
LPG is a petroleum-derived product
distributed and stored as a liquid in
pressurized containers.
LPG fuels have slightly variable properties,but they are generally based on propane
(C3H8) or the less volatile butane (C4H10).
-
8/13/2019 07 Gaseous Fuels
16/50
16
Compared to the gaseous fuel described
above, commercial propane and butane have
higher calorific values (on a volumetric basis)
and higher densities. Both these fuels are heavier than air, which
can have a bearing on safety precautions in
some circumstances.
-
8/13/2019 07 Gaseous Fuels
17/50
17
Typical properties of industrial LPG are given below:
Gas Propane Butane
Density (kg/m3) 1.7-1.9 2.3-2.5Gross calorific value (MJ/m3) 96 122
Boiling point (at 1 bar) -45 0
-
8/13/2019 07 Gaseous Fuels
18/50
18
5. Combustion of Gaseous Fuels
5.1 Flammability Limits
Gaseous fuels are capable of being fully
mixed (i.e. at a molecular level) with the
combustion air.
However, not all mixtures of fuel and air are
capable of supporting, or propagating, a
flame.
-
8/13/2019 07 Gaseous Fuels
19/50
19
Imagine that a region of space containing a
fuel/air mixture consists of many small
discrete (control) volumes.
If an ignition source is applied to one of thesesmall volumes, then a flame will propagate
throughout the mixture if the energy transfer
out of the control volume is sufficient to causeignition in the adjacent regions.
-
8/13/2019 07 Gaseous Fuels
20/50
20
Clearly the temperature generated in the
control volume will be greatest if the mixture
is stoichiometric, where as if the mixture goes
progressively either fuel-rich or fuel-lean, thetemperature will decrease.
When the energy transfer from the initial
control volume is insufficient to propagate aflame, the mixture will be nonflammable.
-
8/13/2019 07 Gaseous Fuels
21/50
21
This simplified picture indicates that there will
be upper and lower flammability limits for any
gaseous fuel, and that they will be
approximately symmetrically distributed aboutthe stoichiometric fuel/air ratio.
-
8/13/2019 07 Gaseous Fuels
22/50
22
Flammability limits can be experimentally
determined to a high degree of repeatability
in an apparatus developed by the US Bureau
of Mines. The apparatus consists of a flame tube with
ignition electrodes near to its lower end
-
8/13/2019 07 Gaseous Fuels
23/50
-
8/13/2019 07 Gaseous Fuels
24/50
24
Intimate mixing of the gas/air mixture is
obtained by recirculating the mixture with a
pump.
Once this has been achieved, the cover plateis removed and a spark is activated.
The mixture is considered flammable if a
flame propagates upwards a minimumdistance of 750 mm.
-
8/13/2019 07 Gaseous Fuels
25/50
-
8/13/2019 07 Gaseous Fuels
26/50
26
5.2 Burning Velocity
The burning velocity of a gas-air mixture is
the rate at which a flat flame front is
propagated through its static medium, and it
is an important parameter in the design ofpremixed burners.
A simple method of measuring the burning
velocity is to establish a flame on the end of atube similar to that of a laboratory Bunsen
burner.
-
8/13/2019 07 Gaseous Fuels
27/50
27
When burning is aerated mode, the flame has
a distinctive bright blue cone sitting on the
end of the tube.
The flame front on the gas mixture istravelling inwards normally to the surface of
this cone.
-
8/13/2019 07 Gaseous Fuels
28/50
-
8/13/2019 07 Gaseous Fuels
29/50
29
If U represents the mean velocity of the gas-air
mixture at the end of the tube and is the half-angle
of the cone at the top of the tube, then the burning
velocity S can be obtained simply from:
S = U sin ()
This method underestimates the value of S for a
number of reasons, including the velocity distribution
across the end of the tube and heat losses from theflame to the rim of the tube.
-
8/13/2019 07 Gaseous Fuels
30/50
30
More accurate measurements are made with a
burner design which produces a flat, laminar flame.
Some typical burning velocities are:
Fuel Burning velocity (m/s)
Methane 0.34
Propane 0.40
Town gas 1.0Hydrogen 2.52
Carbon monoxide 0.43
-
8/13/2019 07 Gaseous Fuels
31/50
31
Burning velocity should not be confused with
the speed of propagation of the flame front
relative to a fixed point, which is generally
referred to as flame speed. In this case, the speed of the flame front is
accelerated by the expansion of the hot gas
behind the flame.
-
8/13/2019 07 Gaseous Fuels
32/50
32
5.3 Wobbe Number
This characteristic concerns the
interchangeability of one gaseous fuel with
another in the same equipment.
In very basic terms, a burner can be viewedin terms of the gas being supplied through a
restricted orifice into a zone where ignition
and combustion take place.
-
8/13/2019 07 Gaseous Fuels
33/50
33
The three important variables affecting the
performance of this system are the size of the
orifice, the pressure across it (or the supply
pressure if the combustion zone is at ambientpressure) and the calorific value of the fuel,
which determines the heat release rate.
If two gaseous fuels are to beinterchangeable, the same supply pressure
should produce the same heat release rate.
-
8/13/2019 07 Gaseous Fuels
34/50
34
This ratio is known as the Wobbe number of agaseous fuel and is defined as:
Some typical Wobbe numbers are:Fuel Wobbe number (MJ/m3)
Methane 55Propane 78Natural gas 50Town gas 27
3
0.5
Gross calorific value (MJ/m )
Relative density (air=1)
-
8/13/2019 07 Gaseous Fuels
35/50
35
The significant difference between the values for natural gas and
town gas illustrates why appliance conversions were necessary
when the UK changed its mains-distributed fuel in 1966.
Example 1:
Calculate the Wobbe number for a by-product gas from anindustrial process which has the following composition by volume:
H2 12%
CO 29%
CH4 3%N2 52%
CO2 4%
-
8/13/2019 07 Gaseous Fuels
36/50
36
Solution:
The gross calorific values are:
CO 11.85 MJ/m3CH4 37.07 MJ/m
3
H2 11.92 MJ/m3
The calorific value of the mixture:CV=(0.1211.92)+(0.2911.85)+(0.0337.07)=5.98 MJ/m3
-
8/13/2019 07 Gaseous Fuels
37/50
37
The relative density of the mixture is
calculated by dividing the mean molecular
weight of the gas by the corresponding value
for air (28.84). The mean molecular weight of this mixture is:
(0.122)+(0.2928)+(0.0316)+(0.5228)+(0.0444)=25.16
-
8/13/2019 07 Gaseous Fuels
38/50
38
The relative density is thus
25.1628.84=0.872.
The Wobbe number is then:
5.98/(0.872)0.5=6.36
The Wobbe number of a fuel is not the only
factor in determining the suitability of a fuel
for a particular burner. The burning velocity of a fuel is also
important.
-
8/13/2019 07 Gaseous Fuels
39/50
39
In general, any device will operate within a
triangular performance map, such as that
sketched in Fig. 7.3 (next slide).
Outside the enclosed region, combustioncharacteristics will be unsatisfactory in the
way indicated on the diagram.
-
8/13/2019 07 Gaseous Fuels
40/50
-
8/13/2019 07 Gaseous Fuels
41/50
41
6. Gas Burners
6.1 Diffusion Burners
The fuel issues from a jet into the
surrounding air and the flame burns by
diffusion of this air into the gas envelope(Fig. 7.4, next slide).
-
8/13/2019 07 Gaseous Fuels
42/50
-
8/13/2019 07 Gaseous Fuels
43/50
43
A diffusion flame from a hydrocarbon fuel has
a yellow color as a result of radiation from the
carbon particles which are formed within the
flame. The flame can have laminar characteristics or
it may be turbulent if the Reynolds number at
the nozzle of the burner is greater than 2,000.
-
8/13/2019 07 Gaseous Fuels
44/50
44
Pratical burner operate in the turbulent
regime since more efficient combustion is
obtained in this case because the turbulence
improves the mixing of the fuel with air. Industrial diffusion burners will have typical
supply gas pressures of 110 Pa.
-
8/13/2019 07 Gaseous Fuels
45/50
45
Diffusion burners have the following positive
characteristics:
(a) Quiet operation
(b) High radiation heat transfer (about 20% ofthe total)
(c) Will burn a wide range of gases (they
cannot light back)
(d) Useful for low calorific value fuels
-
8/13/2019 07 Gaseous Fuels
46/50
46
6.2 Premixed Burners
The vast majority of practical gaseous burners mix
the air and fuel before they pass through a jet into
the combustion zone. In the simplest burners, such as those that are used
in domestic cookers and boilers, the buoyancy force
generated by the hot gases is used to overcome the
resistance of the equipment. However, in larger installations the gas supply
pressure is boosted and the air is supplied by a fan.
-
8/13/2019 07 Gaseous Fuels
47/50
47
The principle is illustrated by the flame from a
Bunsen burner with the air hole open, and is
shown diagrammatically in Fig. 7.5
(next slide).The gas and air are mixed between the fuel
jet and the burner jet, usually with all the air
required for complete combustion.
-
8/13/2019 07 Gaseous Fuels
48/50
-
8/13/2019 07 Gaseous Fuels
49/50
49
The velocity of the mixture through the burner
jet is important.
If the velocity is too low (below the burning
velocity of the mixture) the flame can lightback into the mixing region.
-
8/13/2019 07 Gaseous Fuels
50/50
If the velocity is too high the flame can lift off
from the burner to the extent where it can be
extinguished by, for instance, entrainment of
additional (secondary) air around the burner. The flame from a premixed burner will emit
very little heat by radiation but, because of its
turbulent nature, forced convection in a heatexchanger is very effective.