1 xvy-evolution. 2 continuous current from 3arms to 580arms xvy-evolution
TRANSCRIPT
![Page 1: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/1.jpg)
1
XVy-EVolution
![Page 2: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/2.jpg)
2
Continuous current from 3Arms to 580Arms
XVy-EVolution
![Page 3: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/3.jpg)
3
XVy_EV naming system
XVy_EV 5100180 - KBX - PDP - KBX - PDP
Nominalcurrent (Arms)
Product nameARTDriveS series
Peakcurrent (Arms)
Casesize
Profibus-DPOption Included
Braking moduleoption
By the way to have a clear identification, the new name depends on the Rated and Overload current of the drive
![Page 4: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/4.jpg)
4
NEW Regulation board• The new board won’t change any interface with the
actual one (terminals, jumpers, etc…)• The card is replaceable with the old one (the power
section remains the same)
XVy-EV
![Page 5: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/5.jpg)
5
Regulation board improvement The microcontroller C167 with 25MHz is replaced with the more performing processors
C167CR-L33M working at 32 MHz. This allows:• Improvement of the power calculation and the management of more performing and
complex applications• CanOpen baud rate at 1 Mbit• Improvement of the SoftScope use
XVy-EV
![Page 6: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/6.jpg)
6
Brushless Version• XVyBasic V4_22.sre• XVyBasic V4_22.sre
XVy-EV
Asyncronous Version• XVyABasic V4_22.sre• XVyABasic V4_22.sre
NEW SW version
![Page 7: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/7.jpg)
7
New KeypadThe keypad is the same of the actual AVy,where are also available more navigationButtons:• Start / Stop• Disable• Jog + and Jog –• Motorpot + and -
The name is KBXV-EV
XVy-EV
![Page 8: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/8.jpg)
8
Alphanumeric Keypad• In order to make more user-friendly
the drive interface, the parameters
description is in “alphanumeric” mode.
• The parameters description is in
a single language (short technical terms in English).
File Parameter Storage• The keypad is able to upload and download one file parameter of
the drive.
New FW functions
![Page 9: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/9.jpg)
9
• Improvements of the connection of the absolute encoders EnDat to the expansion card EXP-ABS-XVy.
• It is no longer necessary to double the encoder cable.
• The full data encoder have to be connected to the XE1 connector on the ABS card.
• The new card has a second XE2 connector used to repeat the incremental tracks to the standard XE connector on the regulation board
Hardware Update
![Page 10: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/10.jpg)
10
• Add a new connectors for a fast disconnection / connection of the braking resistor
• Easy disconnection and removal of the cable to the BR1 and C terminal
Hardware Update
![Page 11: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/11.jpg)
11
Digital I/O with NPN and PNP configuration selection
PNP configuration
Hardware Update
![Page 12: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/12.jpg)
12
Digital I/O with NPN and PNP configuration selection
NPN configuration
Hardware Update
![Page 13: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/13.jpg)
13
Fast inputs• Digital inputs 6 and 7 are wired as Hardware Interrupt.
They could be used to store the encoders position.• Input 5 could be used as integrated function “Counter”.
It is able to count squared waveform max 8khz. (positive slope, negative slope, positive and negative slope).
• These functions are available only in MDPLC application.
Hardware Update
![Page 14: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/14.jpg)
14
Fast Link network• Increased the max number of Slave from 7 to 15 (16
taking part in the net)
Hardware Update
XVy XVy XVy XVy
Master Slave 1 Slave .. Slave 15
![Page 15: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/15.jpg)
15
XVy XVy XVy XVy
Section 1Drive X (Master)
Section 2Drive 1
(Master)
XVy
Section 2Drive 16 (Slave)
Section 3Drive 1
(Master)
Section 3Drive 16 (Slave)
Fast Link & encoder repetition can be used together.
Hardware Update
![Page 16: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/16.jpg)
16
NOTE:
The new FW runs only with the new regulator board at 32 MHz.
It is not possible to perform a network through fast-link with drive having both 25MHz and NEW 32MHz processors.
![Page 17: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/17.jpg)
17
Encoder inputs• Pull-up / down resistors added to the optional ENC-ADPT card• Which configuration (NPN – PNP)?
Hardware Up-to-dating
![Page 18: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/18.jpg)
18
XVy-EV SIZES
![Page 19: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/19.jpg)
19
The XVy_EV perform two different overload algorithms:
• IxT controldedicated to high dynamic application where the overload can reach the 200% of the drive rated current
• I2T control suitable in applications where it is requested a lower overload for a longer time (136% In Class1 for 60s every 300s)Typical applications are the continuous lines.
New FW functions
![Page 20: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/20.jpg)
20
Example:For the same machine where is requested a standard overload 150% every 60s we to choice
between an asynchronous solution or a brushless solution with the following data:
AsynchronousAX 100K.2Nominal Torque = 21NmNominal Speed = 3000rpmNominal Current = 15.4ANominal Power = 6.6KW
I2T control
BrushlessSBM78 30 3Nominal Torque = 21NmNominal Speed = 3000rpmNominal Current = 13.3ANominal Power = 6.6KW
![Page 21: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/21.jpg)
21
Example:
Using the current XVy drive we have to select the following size:
AsynchronousCurrent request at Start = 15.4 * 150% = 23.1ADrive size = XVyA-2075-KBX
I2T control
BrushlessCurrent request at Start = 13.3 * 150% = 19.9ADrive size = XVy-32040-KBX
The XVy-32040 have the same power section as the asynchronous version with the size 11KW, so we have to use a brushless drive 1 size greater.
![Page 22: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/22.jpg)
22
Example:
Test of the overload using the current XVy 21530 (with I*T overload control):In = 15AIovld = 30 for Tovld = 1s
Motor overload Imot = 19.9A
Overload control
Tovld 19.9 = (Iovld – In)*Tovld / (Imot – In)Tovld 19.9 = (30 – 15)*1 / (19.9 – 15) = 3.06s
It is not enough for the above mentioned application
![Page 23: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/23.jpg)
23
IxT Control
![Page 24: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/24.jpg)
24
Example:
Test of the overload using the new XVy_EV 21530:In = 17.7AIsl-ov = 24.1 for Tsl-ov = 60s
Motor overload Imot = 19.9A
I2T control
Tsl-ov19.9 = (Isl-ov2 – In
2)*Tsl-ov / (Imot2 – In
2)Tsl-ov19.9 = (24.12 – 17.72)*60 / (19.92 – 17.72) = 194s
It is right for the above mentioned application
![Page 25: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/25.jpg)
25
I2T Control
![Page 26: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/26.jpg)
26
Password
It has been implemented a Password with two entry level
1. User: to avoid modifications in the file parameter of the drive by not authorized people
The customer can set his personal value.
2. Service: reserved to SIEI personnel only
Both the password value has to be set in the same parameter:
Keypad PSWD
The “User” password has effect only by using the keypad. If used, it allows to read only the MONITOR parameter.
Using the E@syDrive configuration software it is anyway possible to read all the parameter (apart the Service menu)
New FW functions
![Page 27: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/27.jpg)
27
• Implementation of the management of encoders with EnDat 2.2 protocol
• Added HYPERFACE protocol on EXP-ABS-XVy optional card
Increase of the number of words• The number of words exchangeable through filedbus
(DeviceNET, CANOpen ProfibusDP) will be increased from 8 to 12
New FW functions
![Page 28: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/28.jpg)
28
Coast-through function• The coast-through function will be improved adding the emergency-
stop function (same as AVy version 1.9 FW).
New FW functions
![Page 29: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/29.jpg)
29
• HELPER
Integrated into the Basic Firmware the ability to send a torque output signal to a slave through Fast-link. Refresh time = 250micros
New FW functions
![Page 30: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/30.jpg)
30
SPEED DRAW
• This function allows to multiply the Speed reference times a Speed Draw Ratio settable by Analog Input or Bus (same as AVy version 1.9 FW).
• The multiplier will be bypassed in case of Jog or
Configuration Mode Speed
New FW functions
![Page 31: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/31.jpg)
31
• This function allows to set a Speed reference by Keypad, Digital Input, Serial line or Bus.
• The output of the motor potentiometer can be add to a Speed Reference or used as a multiplier of the Speed reference (through the Speed Draw function).
MOTOR POTENTIOMETER
![Page 32: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/32.jpg)
32
• When the Motor potentiometer is used as multiplier of the Speed Reference, it is possible to set the Min. and Max. multiplier factor.Doing that the operator can define for example to multiply the main reference within a defined ratio e.g. +/- 15%.
MOTOR POTENTIOMETER
• If the Motor pot is used in addition to the main reference, the standard Ramp of the drive will be overwrite by the Motor pot acceleration and deceleration time.
• If the Motor pot is used to multiply the main reference, the standard Ramp of the drive is fully independent from the Motor pot acceleration and deceleration time.
• If a Motor Pot command is assigned to a Digital Input, this have priority compared to any setting via Keypad, Serial line or Bus
![Page 33: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/33.jpg)
33
• Positioning control without Homing needed
• Position Reference via Analog Input.
The Position Mode parameter must to be set in “Absolute”
10V on the Analog Reference correspond to “Max Pres Abs Val”
The Position reference is showed in the parameter Pos preset 0
There are two way to use this function:
Pos An Mode = Step
Pos An Mode = Continuous
New FW functions
POSITIONING CONTROL
![Page 34: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/34.jpg)
34
• Pos An Mode = Step
When the motor reaches the Position reference (Pos Reached = On), any other modification in the reference will be ignored.
To start for a new set point it is necessary to give one more “Pos Start Pos” command.
If the Position reference is continuously modified during the movement of the motor, it is continuously refreshed.
If, during the movement of the motor, the Position reference became stable, any other modification will be ignored.
ANALOG POSITION REFERENCE
![Page 35: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/35.jpg)
35
• Pos An Mode = Continuous
The position reference is continuously refreshed.
Any modification in the Position reference will be followed by the motor without any transition in the “Pos Start Pos” command.
It is strongly recommended to well set the parameter
Pos An Wind Del
Pos An Stdy Wind
Pos An Filter = 0 (default value = 0.2)
ANALOG POSITION REFERENCE
![Page 36: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/36.jpg)
36
Multi Positioning Control (sequence of events)• It is possible to define a sequence of position defined
in “Pos Preset 0” and “Pos Preset 7”.
• When a position is reached it is possible to go on with the next position if is verified a defined condition.
Possible condition are:• Delay after Pos Reached• Event from Digital Input or Bus• Delay + Event
New FW functions
POSITIONING CONTROL
![Page 37: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/37.jpg)
37
• Depending on the application, it is possible to configure the parameter Position Mode in “Absolute” or in “Incremental” mode.
• Making a loop between the “Pos Preset X” it is possible to work continuously like for a Belt Conveyor
POSITIONING CONTROL
Multi Positioning Control
![Page 38: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/38.jpg)
38
• The tool recognize directly the Drive Size and Software Version
• It is possible to work ONLINE or OFFLINE
E@SYDRIVE tool
![Page 39: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/39.jpg)
39
• It is possible to select the new Software Version (4.22) or the old ones (without HTML pages)
E@SYDRIVE tool
![Page 40: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/40.jpg)
40
• It is possible to edit the XVy parameter list or to use the Wizard E@SYDRIVE tool
![Page 41: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/41.jpg)
41
• It is possible to select the motor and than automatically set the parameter into the drive using the Motors Database
E@SYDRIVE tool
![Page 42: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/42.jpg)
42
• It is possible to define a new Motors Database E@SYDRIVE tool
![Page 43: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/43.jpg)
43
• After the Import Data command the new Motor well be imported in the Data Base
E@SYDRIVE tool
![Page 44: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/44.jpg)
44
• New SoftScope2 Version 1.0it is possible to open the scope tool directly from E@syDrive icons:Service -> Tools -> Softcope
E@SYDRIVE tool
![Page 45: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/45.jpg)
45
New HTML pages for Custom application
• It is on development by the Application Office a normalization of some of the last application realized in particular: Flying Shear and Feeders control.
• These application will be downloadable in the regulation card and manageable through the PC configuration software E@sy Drive by using some dedicated HTML pages.
• The pages will be specifically related to the application itself and then from here all the data could be changed and monitored.
![Page 46: 1 XVy-EVolution. 2 Continuous current from 3Arms to 580Arms XVy-EVolution](https://reader035.vdocument.in/reader035/viewer/2022062518/56649e4b5503460f94b40767/html5/thumbnails/46.jpg)
46
Password for special applications
FOR SPECIAL SIEI APPLICATIONS IT IS NECESSARY
A DEDICATED PASSWORD
IN THIS CASE THE CUSTOMER WILL RECEIVE A PLC KEY THAT WORKS WITH JUST THE APPLICATION HE ASKED FOR.
XVy-EV