10gb/s dwdm sfp+ 80km transceiver rdpx0szr-xxx · c-band dwdm eml enhanced laser transmitter...
TRANSCRIPT
RoHS Compliant
Rev. A.7, 07/31/2013 1
Features RoHS compliant
Support multi protocol from 9.9Gb/s to 11.3Gb/s
Compliant with SFP+ MSA, SFF 8431 Rev. 4.1
Compliant with SFF 8432 Rev.4.3 mechanical
dimension
Compliant with Digital diagnostic SFF-8472
Rev.11.0
Transmission distance of 80km over single mode
fiber
C-band DWDM EML laser transmitter
LC duplex connector
Hot pluggable 20 pin connector
Single power supply voltage : +3.3V
Low power dissipation
Three optional operating temperature ranges :
Option ST : 0°C to 70°C
Option ET : -5°C to 85°C
Option IT : -40°C to 85°C
Applications
SONET OC-192 / STM-64 : P16L1-2A2
10GBASE-ZR/ZW Ethernet
80km 10G FC
G.709 OUT-2
Description
OE Solutions’ Small Form Factor Pluggable
(SFP+) transceivers are compatible with the
Small Form Factor Pluggable 20pin Multi-
Source Agreement (MSA). The high performance
cooled DWDM EML transmitter and high
sensitivity APD receiver provide superior
performance for SONET/SDH and Ethernet
applications up to 80km optical links.
Enhanced Digital Diagnostics functions are
available via the 2-wire serial bus specified in the
SFF-8472 Rev. 11.0. The transmitter and receiver
features ac-coupled differential data inputs and
outputs, and an LVTTL for Tx disable input and
Tx fault output. Software TX disable is also
implemented. The receiver features differential
ac-coupled data outputs and LVTTL for LOS
(Loss of Signal) output.
10Gb/s DWDM SFP+ 80km Transceiver
RDPX0SZR-xxx
Rev. A.7, 07/31/2013 2
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
1. Absolute Maximum Ratings
Parameter Symbol Min. Typ. Max. Unit Notes
Absolute Supply Voltage Vcc_max 0 - 3.6 V -
Operating Case Temperature Top -40 - 85 °C 1,3
Operating Relative Humidity RHop 5 - 90 % 2
Storage and Transportation Temperature Tst -40 - 85 °C 2
Storage and Transportation
Relative Humidity
5 - 95 % 2
Notes: 1. Measured on top side front center of SFP module 2. Non-condensing 3.There are three options of operating maximum temperature:
Option ST: standard temperature from 0oC to 70
oC,
Option ET: extended temperature from -5oC to 85
oC
Option IT: extended temperature from -40oC to 85
oC
2. General Operating Conditions
Parameter Symbol Min. Typ. Max. Unit Notes
Bit Rate B 9.9 10.3 11.3 Gb/s -
Maximum Transmission Distance Dmax 80 - - km -
Operating Voltage Vcc 3.14 - 3.46 V -
Power Supply Current ICC - - 650 mA ST
- - 750 mA ET, IT
Total Power Consumption - - 2.1 W -
ESD (High speed pins) - - 500 V 2
Notes : 1. Supplies TEC, Current draw depends on Temperature 2. Human body model per JEDEC JESD22-A114-B, compliant with INF-8077i Rev. 4.5 August 31, 2005
Rev. A.7, 07/31/2013 3
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
3. Electrical Specifications
3.1 Transmitter Electrical Specifications (Over Operating Case Temperature and Power Supply Range)
Electrical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes
Differential Input Impedance Rin 80 100 120 Ω -
Differential Data Input Swing Vin,pp 180 - 800 mVp-p -
Data Input Rise/Fall Time tr/tf 15 - 40 ps
Tx Disable Voltage Vd 2.0 - Vcc+0.3 V 1
Tx Enable Voltage Ven 0 - 0.8 V -
Tx Fault Output Low Vtfl - - 0.4 V -
Tx Disable Assert Time T_off - - 100 s -
Tx Enable Assert Time T_on - - 2 ms -
Tx Fault Assert Time Tx_f_on - - 1 s -
Tx Fault Reset Time Tx_reset 10 - - s -
Initialization Time T_start_up_cooled - - 90 s -
Note : 1. Vcc is the voltage of host board
3.2. Receiver Electrical Specifications (Over Operating Case Temperature and Power Supply Range)
Electrical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes
Data Rate B 9.9 10.3 11.3 GBd -
Differential Output Impedance Rout 80 100 120 Ω -
Differential Data Output Swing Vout 300 - 800 mVp-p -
Data Output Rise/Fall Time tr/tf - - 45 ps -
LOS Output High Voltage Vlosh Vcc-0.5 - Vcc+0.3 V 1
LOS Output Low Voltage Vlosl 0 - 0.4 V -
LOS Assert/Deassert Time Delay T_los on/off - - 100/100 s/s -
Note : 1. Vcc is the voltage of host board
Rev. A.7, 07/31/2013 4
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
4. Optical Specifications
4.1 Transmitter Optical Specifications (Over Operating Case Temperature and Power Supply Range)
Optical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes
Laser Safety Class Class 1 according to IEC60825 -
Optical Wavelength λ 1529 - 1562 nm -
Average Optical Output Power Pout -1 - 4 dBm 1
Optical Power Overshoot Pov - - 1 dB 2
Optical power of OFF transmitter Pout-off - - -40 dBm -
Spectral Width -8 - 8 GHz 3
Optical Output Power Variation
(with respect to BOL Tc=25C,
and nominal power supply)
Pout -1 - +1 dB -
Side Mode Suppression Ratio SMSR 35 - - dB 4
Wavelength
Deviation
BOL T -50 - +50 pm 5
EOL a -100 - +100 pm
Optical Extinction Ratio(Filtered) ER 8.2 - - dB -
Optical Rise/Fall Time (20%-80%) Tr, Tf - - 35 ps -
Output Jitter - - - - 6
Notes: 1. Average power measured at output 2. Defined as Peak power – Steady-state power (in dBm) when Tx-dis is de-asserted or when the module is hot plugged with Tx_dis in low state (Tx enabled). 3. Full spectral width (RBW=0.1nm) measured 15dB down from the maximum of center wavelength peak under full modulation condition 4. Ratio of the average output power in the dominant longitudinal mode to the power in the most significant side mode peak under full modulation condition 5. Deviation related to the ITU standardized wavelength. The EOL value is met as soon as the output average power is above 10% of the steady-state power. 6. The jitter performance meets Telcodia GR-253-Core and ITU-T Recommendations G.783, G813, G825 and G82511 with ITU-T 0.172(04/2005) for the measurement methods and the measurement equipment.
Laser Safety: All transceivers in this datasheet are Class I Laser products per FDA/CDRH and IEC-60825 standards.
They must be operated under specified operating conditions.
Rev. A.7, 07/31/2013 5
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
4.2 ITU Channel and Wavelength Guide
ITU Channel Frequency
(THz)
Wavelength
(nm) ITU Channel
Frequency
(THz)
Wavelength
(nm)
39 193.9 1546.12
40 194.0 1545.32
17 191.7 1563.86 41 194.1 1544.53
18 191.8 1563.05 42 194.2 1543.73
19 191.9 1562.23 43 194.3 1542.94
20 192.0 1561.42 44 194.4 1542.14
21 192.1 1560.61 45 194.5 1541.35
22 192.2 1559.79 46 194.6 1540.56
23 192.3 1558.98 47 194.7 1539.77
24 192.4 1558.17 48 194.8 1538.98
25 192.5 1557.36 49 194.9 1538.19
26 192.6 1556.56 50 195.0 1537.40
27 192.7 1555.75 51 195.1 1536.61
28 192.8 1554.94 52 195.2 1535.82
29 192.9 1554.13 53 195.3 1535.04
30 193.0 1553.33 54 195.4 1534.25
31 193.1 1552.52 55 195.5 1533.47
32 193.2 1551.72 56 195.6 1532.68
33 193.3 1550.92 57 195.7 1531.90
34 193.4 1550.12 58 195.8 1531.12
35 193.5 1549.32 59 195.9 1530.33
36 193.6 1548.51 60 196.0 1529.55
37 193.7 1547.72
38 193.8 1546.92
Rev. A.7, 07/31/2013 6
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
4.3. Receiver Optical Specifications (Over Operating Case Temperature and Power Supply Range)
Optical Characteristics
Parameter Symbol Min. Typ. Max. Unit Notes
Optical Wavelength λ 1528 1563 nm -
Average Rx Sensitivity@10Gb/s RSENS - - -23 dBm 1, 2
Maximum Input Power Pol -6.0 - - dBm -
Receiver Reflectance - - - -27 dB -
LOS Assert LOS_A -35 - - dBm -
LOS De-assert LOS_D - - -23 dBm -
LOS Hysteresis - 0.5 - 5 dB -
Notes : 1. Measured with a PRBS of 231
-1 at 1x10-12
BER and 8.2 dB extinction ratio, 1450ps/nm
2. Guaranteed after 80km transmission over the entire operating temperature range.
Rev. A.7, 07/31/2013 7
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
5. Pin Descriptions
SFP Transceiver Electrical Pad Layout
Tx GND
TD-
TD+
Tx GND
VccT
VccR
Rx GND
RD+
RD-
Rx GND
Tx Fault
Tx Disable
SDA
RS0
Rx_LOS
RS1
Rx GND
SCL
Mod_ABS
20
19
18
17
16
15
14
13
12
11
1
2
3
4
5
6
7
8
9
10
Top of Board Bottom of Board
Tx GND
Rev. A.7, 07/31/2013 8
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
Pin Descriptions (continued)
Pin Logic Symbol Description Plug Seq. * Notes
1 - Tx GND Transmitter Ground 1 1
2 LVTTL-O Tx Fault Transmitter Fault Indication 3 2
3 LVTTL-I Tx Disable Transmitter Disable 3 3
4 LVTTL-I/O SDA 2 wire Serial Interface Data Line 3 4
5 LVTTL-I/O SCL 2 wire Serial Interface Clock 3 4
6 -
MOD_ABS Module Absent, connected to Tx GND or Rx GND in the module
3 5
7 LVTTL-I RS0 Rate Select 0, not used 3 6
8 LVTTL-O Rx LOS Receiver Loss of Signal Indication (In FC designated as Rx_LOS and in Ethernet designated as Signal Detect Bar
3 7
9 LVTTL-I RS1 Rate Select 1, not used 3 6
10 - Rx GND Receiver Ground 1 1
11 - Rx GND Receiver Ground 1 1
12 CML-O RD- Receiver Negative Data Out 3 -
13 CML-O RD+ Receiver Positive Data Out 3 -
14 - Rx GND Receiver Ground 1 1
15 - Vcc Rx Receiver Power, 3.3V±5% 2 -
16 - Vcc Tx Transmitter Power, 3.3V±5% 2 -
17 - Tx GND Transmitter Ground 1 1
18 CML-I TD+ Transmitter Positive Data In 3 -
19 CML-I TD- Transmitter Negative Data In 3 -
20 - Tx GND Transmitter Ground 1 1 *Plug Seq. : Pin engagement sequence during hot plugging Notes : 1. The module ground contacts, Tx GND abd Rx GND, shall be isolated frim the module case, that is, frame ground. 2. Tx Fault is an open collector/drain output that shall be pulled up with a 4.7k ~ 10k on the host board. Pull up voltage
between 2.0V and VccT + 0.5V. When high, output indicates a laser fault of some kind. When low, output indicates normal operation. The LD output is not turned off in case of Tx Fault
3. Tx Disable is an input that is used to shut down the transmitter optical output. It is pulled up within the TRx with a 4.7k ~ 10k to VccT.
4. SDA and SCL should be pulled up with a 4.7k ~ 10k on the host board. The pull-up voltage shall be VccT. SCL is the clock line of 2-wire serial interface for serial ID. SDA is the data line of 2-wire serial interface for serial ID.
5. Mod_ABS is connected to Tx GND or Rx GND in the SFP+ module. The host may pull the contact up to Vcc on the host board with a resistor in the range 4.7 ~ 10k. Mod_ABS is asserted “high” when the SFP+ module is physically absent from a host slot. In the SFP MSA (INF-8074i) this contact has the same function but is called MOD_DEF0.
6. RS0 and RS1 are module input rate select contacts and are pulled low to Tx GND with a >30k resistor in the module. RS0 is an input hardware contact which optionally selects the optical receive data path rate coverage for an SFP+ module. RS1 is an input hardware contact which optionally selects the optical transmit path data rate coverage for the SFP+ module. These contacts can also be used for AS0 and AS1 if implementing SFF8079. RS1 is commonly connected to Tx GND or Rx GND in the classical SFP modules. The host needs to ensure that it will not be damaged if this contact is connected to Tx GND or Rx GND in the module. For logical definitions of RS0/RS1, see Section 2.5 of SFF-8431 Rev. 2.1.
7. LOS is an open collector output. Shall be pulled up with a 4.7k ~ 10k on host board. Pull up voltage between 2.0 and VccR+0.3. Logic 0 indicates normal operation.
Rev. A.7, 07/31/2013 9
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
5. Outline Drawings
Dimensions are in millimeters
Rev. A.7, 07/31/2013 10
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
6. PCB layout and Bezel recommendation
Dimensions are in inches (millimeters)
Notes : 1. Datum and basic dimensions established by customer.
2. Pads and vias are chassis ground, 11 locations
3. Thru holes, plating optional.
Rev. A.7, 07/31/2013 11
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
7. PCB layout and Bezel recommendation (continued)
Notes : Thru holes, plating optional.
Recommended Panel Opening
Rev. A.7, 07/31/2013 12
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
8. SFP+ Block Diagram, Power Supply Information and Host Board Interface
8.1 SFP+ Block Diagram
TOSA
TOSA
Laser
driver
Post amp.
Vcc Tx
Tx_GND
LOS
RD-
RD+
TD+
TD-
Tx Disable
Tx Fault
SCL
SDA EEPROM
10k
100
Management processor
Vcc Rx
Rx_GND
Zin diff.=
100
Zout = 50
each arm
Pin 16
Pin 3
Pin 18
Pin 19
Pin 2
Pin 1, 17, 20
Pin 5
Pin 4
Pin 15
Pin 12
Pin 13Pin 8
Pin 10, 11, 14
RS0
RS1
Pin 7
Pin 9
Mod ABS Pin 6
Rev. A.7, 07/31/2013 13
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
8.2 Recommended Host Board Supply Filtering Network
8.3 SFP+ Host Board Interface
Note 1: Host board output device circuit in the transmitter side and host board input device circuit in the receiver should be
carefully designed to meet 100ohm differential impedance matching. Also necessary is the dc bias circuit of each
input and output by taking into account of ac coupling of data input ant output of SFP+ module. For the interface of
host board devices, it is recommended to refer to the device vendor’s data sheet.
1H
1H
0.1F
0.1F
10F 10F 0.1F
Vcc +3.3V
SFP+ Module
Vcc Tx
Vcc Rx
HOST BOARD
Tx GND
Rx GND
Host Board GND
1 Tx GND
2 Tx Fault
3 Tx Disable
4 SDA
5 SCL
6 Mod ABS
7 RS0
8 Rx LOS
9 RS1
10 Rx GND
Tx GND 20
TD- 19
TD+ 18
Tx GND 17
Vcc Tx 16
Vcc Rx 15
RX GND 14
RD+ 13
RD- 12
Rx GND 11
10k
Vcc
10k
Vcc
10k
Vcc
10k
Vcc
10k
Vcc
Host board
Device
Host board
Device
Differential 100(note 1)
Differential 100(note 1)
Refer to Section 8.2
SFP+ Module
Rev. A.7, 07/31/2013 14
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
9. Digital Diagnostic Monitoring and Serial ID Operation
The information is accessed through the pin 4 (SDA), and pin 5(SCL) of the module. The device
address used to read the Serial ID data is 1010000X(A0h), and the address to read the diagnostic data is
1010001X(A2h). The EEPROM Write Protect pin is internally tied to ground with no external access,
allowing write access to the customer-writable field (bytes 128-247 of address 1010001X). Address
bytes 0-127 are not write protected and may cause diagnostic malfunctions if overwritten.
The information stored in the EEPROM, including the organization and the digital diagnostic
information, is defined in the Small Form-Factor document SFF-8472 Rev. 11.0, dated September,
2010.
9.1 Data Field Descriptions, and Serial ID Data and Map
9.2 Serial ID and Map: page A0h
Address HEX Name of Fields Description
0 03 Identifier SFP+
1 04 Ext. Identifier GBIC/SFF function is defined by serial ID only
2 07 Connector LC
3 00 Infiniband Compliance Unallocated
4 10 Reach Specifier SONET IR-1/LR-1 compliant
5 00 SONET
6 00 Gigabit Ethernet
7 00 Fiber Channel link length Unallocated
8 00 Transmitter technology Unallocated
9 01 Transmission media Single Mode (SM)
10 00 Fiber Channel Speed
Address(1010000X) (A0h) Address(1010001X) (A2h)
Serial ID Information:
Defined by SFP MSA
OE Solution Specific
Information
Reserved for SFP MSA
Alarm and Warning Limits
Reserved for External
Calibration Constants
Real Time Diagnostic
Information
OE Solutions Specific
Information
OE Solutions Specific Information
Non-volatile, customer-
writeable, field-writeable
area
0
95
127
255 255
247
119
127
95
0
55
Rev. A.7, 07/31/2013 15
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
11 06 Encoding 64B/66B
12 67 Nominal Bit Rate 10.30 Gbps
13 00
14 50 Length(9u)[km] 80 Km
15 FF
16 00 Length(50u,OM2)[m] Not support
17 00 Length(62.5u,OM1)[m] Not support
18 00 Length(copper) Not support
19 00 Length(50u,OM3)[m] Not support
20 4F
Vendor Name
O
21 45 E
22 20
23 53 S
24 4F O
25 4C L
26 55 U
27 54 T
28 49 I
29 4F O
30 4E N
31 53 S
32-35 20
36 00 Reserved
37 00
Vendor OUI
00
38 19 19
39 3A 3A
40 52
Vendor PN
R
41 44 D
42 50 P
43 58 X
44 30 0
45 53 S
46 5A Z
47 52 R
48 2D -
49 xx xx = (5Ah for ST, 45h for ET, 49h for IT)
50 xx xx=(31h:1, 32h:2,33h:3,34h:4,35h:5,36h:6)
51 xx xx=(30h:0, 31h:1, 32h:2,33h:3,34h:4,35h:5,36h:6,37h:7, 38h:8, 39h:9)
52-55 20
56 30
Vendor Rev.
0
57 31 1
58 2E .
59 Varies Varies
60
Note 1 Wavelength[nm]
61
62 Wavelength(@10pm)
63 Varies CC_BASE Checksum over 0 to 62
64 04
Option Values
Cooled Transceiver[2]
Power Level[1]
Linear Receiver Output[0]
Cooled Laser implementation
Rev. A.7, 07/31/2013 16
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
65 3A
Option Values
Rate Select[5]
Tx Disable[4]
TX Fault[3]
SD[2]
LOS[1]
Rate Select[5]
Tx Disable[4]
TX Fault[3]
LOS[1]
66 00 Bit Rate, max[%] Not Specified
67 00 Bit Rate, min[%] Not Specified
68-83 Varies Vendor S/N Varies
84-91 Varies Date Code Varies
92 68
Diagnostic Monitoring Type
Digital diagnostic[6]
Internally Cailbrated[5]
Externally Calibrated[4]
Average Power[3]
Address change req[2]
Digital diagnostic[6]
Internally Calibrated[5]
Average Power[3]
93 F0
Enhanced Options
Alarm/Warm Impl.[7]
Soft TX Dis Control[6]
Soft TX Fault monitor[5]
Soft Rx LOS monitor[4]
Soft RATE_SEL Control[3]
App Select Control[2]
Rate Select Control[1]
Alarm/Warm Impl.[7]
Soft TX Dis Control[6]
Soft TX Fault monitor[5]
Soft Rx LOS monitor[4]
94 05 SFF-8472 Compliance Rev 11.0 of SFF-8472
95 Varies CC_EXT Check Sum Byte for Bytes 64 to 94
96-127 00 Vendor Specific
128-163 Varies OES'DATA OES'DATA
164-247 00 Reserved Reserved
248-255 Varies OES'DATA OES'DATA
Note 1. 16-bit integer value in nm with byte 60 as high byte, byte 61 as low byte. The fractional part of the wavelength in
units of 0.01nm written in byte 62. Varies
9.3 Diagnostics
The enhanced digital diagnostics feature monitors five key transceiver parameters which are internally
calibrated and should be read as absolute values.
A2h address Parameter Calibration Accuracy Range
96-97 Temperature Internal +/- 3oC Note 1
98-99 Vcc Internal +/- 3% 3.13 to 3.47
100-101 Tx bias Internal +/- 10% Note 2
102-103 Tx power Internal +/- 2dB -1 to +4Bm
104-105 Rx Power Internal +/- 2dB -23 to -6dBm
Note: 1) Junction temperature of temperature sensing device. Monitoring range is from -40oC to 125
oC.
2) Specified by nominal value
Rev. A.7, 07/31/2013 17
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
9.4 Alarm Boundary Conditions
1) Transmitter Output Power and Receiver input power
Model Name Tx Low
Warning
Tx Alarm Tx High
Warning
Rx Low
Warning
Rx Alarm Rx High
Warning Low High Low High
RDPX0SZR-xxx -2.5 dBm -3 dBm 6 dBm 5.5 dBm -25 dBm -28 dBm -5 dBm -6 dBm
2) Power Supply and Transmitter Bias Current
Model Name Vcc Low
Warning
Vcc Alarm Vcc High
Warning
Bias Low
Warning
Bias Alarm Bias High
Warning Low High Low High
RDPX0SZR-xxx 3.14V 2.97 3.63V 3.47V 50mA 40mA 130mA 120mA
3) Temperature
Model Name Temp. Low Warning Temperature Alarm
Temp. High Warning Low High
RDPX0SZR-Sxx -5oC -8
oC +73
oC +70
oC
RDPX0SZR-Exx -5oC -8
oC +88
oC +85
oC
RDPX0SZR-Ixx -40oC -43
oC +88
oC +85
oC
10. Regulatory Compliance
RDPX0SZR comply with international Electromagnetic Compatibility (EMC) and international safety
requirements and standards. EMC performance is dependent on the overall system design. The RDPX0SZR is
lead-free and RoHS-compliant per Directive 2011/65/EU of the European Parliament and of the Council of 8
June 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment..
11. Label
1. P/N : RDPX0SZR-xxx / 2. Bit rate , Reach , Wavelength : 10G 80km 1xxx.xxnm / 3. S/N
Rev. A.7, 07/31/2013 18
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
12. Ordering Information
Model Name OES P/C Operating Case
Temperature Nominal
Wavelength Latch Color
Application Distance
RDPX0SZR-Sxx Gxx02 0oC to 70oC
C-band
DWDM
(See Section 4.2)
White SONET/SDH
& 10G GbE 80km
RDPX0SZR-Exx Gxx10 -5oC to 85oC
C-band
DWDM
(See Section 4.2)
White SONET/SDH
& 10G GbE 80km
RDPX0SZR-Ixx Gxx08 -40oC to 85oC
C-band
DWDM
(See Section 4.2)
White SONET/SDH
& 10G GbE 80km
Notice: This data sheet is subject to change at any time without notice.
Revision History
Date Rev. # Description Author(s)
12/13/2010 A.0 Initial Release JSYU/KSP
08/30/2011 A.1 Latch Color: White
Detailed specs for Rx Sensitivity, Path penalty, ONSR w.r.t BER
JSYU
05/09/2012 A.2 Power consumption revised: 2.1W (Standard Temp) JSYU
09/15/2012 A.3 Total current changed(Max. 650mA → 545mA) JSYU
11/23/2012 A.4 Typo
(Optical Extinction Ratio (Unfiltered) → Optical Extinction
Ratio(filtered))
Datasheet correction
(SONET OC-192 LR-2 / SDH L-64.2a → SONET OC-192 / STM-64 :
P16L1-2A2)
ET, IT added
JSYU
06/26/2013 A.5 Bias High Alarm/Warning changed(120mA/110mA→130mA/120mA) JSYU
07/19/2013 Rev.A.6 Total Current changed
(ST : Max. 550mA → 650mA / ET,IT : 700mA → 750mA)
Path Penalty changed : 2dB → 2.5dB
JSYU
07/31/2013 Rev.A.7 Sensitivity and LOS De-assert changed (Max. -24dBm → Max. -23dBm)
Path Penalty deleted
Transmitter Output Power and Receiver input power changed
JSYU
Rev. A.7, 07/31/2013 19
RDPX0SZR-xxx DWDM SFP+ Transceiver Product Specifications
Contact Information:
OE Solutions Co. Ltd. (Korea) Techno Park, 958-3, Daechon-Dong, Buk-Gu, Gwangju, Korea, 500-470. Tel: +82-62-602-7813, Fax: +82-62-602-7639, www.oesolution.com.
OE Solutions America, Inc. 560 Sylvan Avenue, 1
st Floor, Englewood Cliffs, NJ 07632
Tel: 201-568-1188 Fax:201-568-1177Tel: +1-201-224-2377, Fax: 1-949-272-3200