1289865120426

7/31/2019 1289865120426

1/15

Hoot : Instructions 1

Rob Ives www.robives.com

1 2

Thread the long tabs on the wings

through the semi-circular holes in the

body and glue the body tabs to the

wings. (1)

Fold in and glue the three darts on the

body. (2)

Roll round the body and glue it into

place. (3)

You will need a craft knife or other sharp knife, a pair of scissors, some glue

and a glue spreader.

The best type of glue to use is white school glue (PVA.)

Print out the parts sheets onto thin cardboard. If you want to save ink, or prefer

to colour in the model yourself, print out the mono pages. Photocopier card is

ideal. Notice that the parts pages are marked front and back. Print out a front

page, flip it over, then print the back onto the same sheet. Leave the ink to dry

completely before continuing.

Before cutting anything out, score along all the dotted lines and cut out any

holes with a craft knife. Both these jobs are easier to do on full sheets of card.

Dashed lines are hill folds, dotted lines are valley folds. Cut along the solid

lines. Grey areas show where to glue

Cut

out

Dashed lines are

hill folds

Dotted lines are

valley folds

Black or White lines

show where to cut.

Shaded areas show

where to glue.

7/31/2019 1289865120426

2/15


3 4

5 6

Glue the

head down to

the top of the

body. (4)

It is made

slightly too

big; once the

glue is dry

trim the part

to size with

your scissors.

Glue togetherthe beak parts.

(5)

Glue the beak

and eyes to the

body. (6)

Youll need two

coins about this

size. These will

act as weights

Wrap the coin holders round

the coins. (7)

Glue them to the inside front

and back of the body. (8)

Fold round and glue together the

legs and the push rod as shown

above. (9 - 10)

Glue the push rod end into the top of

the head. (11) Use the end of a pencil

or a chop stick to press down theflaps to help the glue dry.

Fit the legs into the body. Glue the

long tabs to the legs. (12)

7/31/2019 1289865120426

3/15


7 8

9

Glue the box top to the legs. (13)

Fold round the four flaps on the

outside(14)

Assemble the button as shown below

(15) and glue on the button top.(16-17)

Glue the button to the end of the

push rod. (18)

Fold round and glue down the tabs on

the box tabs to make a triangular

section. (19)

Glue together the two parts of the box

and complete it as shown. (20-21)

Complete the owl by gluing the box top to the

box. (22)Once the glue is dry make Hoot flap his wings

by pressing the button under the box.

7/31/2019 1289865120426

4/15

HOOT! Parts. Front 1

Push rod

Beak E

yes

Wings

Head

top

12

1

12

1

10

7/31/2019 1289865120426

5/15

10

11

11

11

11

18

18

55 6a6a

11

11

Parts. Back 1

7/31/2019 1289865120426

6/15

22

21

21

19

20

22

22

13

13

12 12

17

17

13 13

9.

22

21

21

19

20

(cc) Rob Ives www.robives.com


Box

Box

Legs

BoxTop

Button

Top

7/31/2019 1289865120426

7/15

22

19

21 21

20

22

19

21 21

20

22

22

18

18

9

.

Parts. Back 2

7/31/2019 1289865120426

8/15

4

4

4 4

4

222

6a

6b

8 7 8 7

14 14 14 14 15

1616

3


Push Button

Body

Coin Holder Coin Holder

7/31/2019 1289865120426

9/15

7 7

3

88

14 14 14 14

17 1715

Parts. Back 1

7/31/2019 1289865120426

10/15

HOOT! Parts. Front 1 (mono)

Push rod

Beak E

yes

Wings

Head

top

12

1

12

1

10

7/31/2019 1289865120426

11/15

10

11

11

11

11

18

18

55 6a6a

11

11

Parts. Back 1

7/31/2019 1289865120426

12/15

22

21

21

19

20

22

22

13

13

12 12

17

17

13 13

9.

22

21

21

19

20

(cc) Rob Ives www.robives.com


Box

Box

Legs

BoxTop

Button

Top

7/31/2019 1289865120426

13/15

22

19

21 21

20

22

19

21 21

20

22

22

18

18

9

.

Parts. Back 2

7/31/2019 1289865120426

14/15

4

4

4 4

4

222

6a

6b

8 7 8 7

14 14 14 14 15

1616

3


Push Button

Body

Coin Holder Coin Holder

7/31/2019 1289865120426

15/15

7 7

3

88

14 14 14 14

17 1715

Parts. Back 1

1289865120426

Documents