8/10/2019 129630_1_en

1/8

MU120111A 10/100M Ethernet ModuleMU120112A Gigabit Ethernet ModuleFunction Upgrades (Version 2.1)

For MD1230A Data Quality AnalyzerMU120111A/MU120112A Features

OSPF Protocol (MD1230A-07)OSPF Emulation satisfying the RFC2328 OSPF Version 2standards can be performed by adding the optionalMD1230A-07 OSPF Protocol software. Up to 200 virtualrouters can be registered for each physical port and each of

Router-LSA, Network-LSA, Summery-LSA, AS-external-LSA,and NSSA External-LSA can be registered for each router. Asa result, HELLO packets, Database Description packets, Link-State Request packets, Link-State Update packets and Link-State Acknowledgement packets are all acknowledged (sendand receive).Note: DR and BDR operation is not supported.

MPLS (LDP/CR-LDP) Protocol (MD1230A-08)LDP and CR-LDP emulation satisfying the RFC3036 andRFC3212 standards can be performed by adding the option-al MD1230A-08 MPLS (LDP/CR-LDP) Protocol software.Adjacent LSR detection can be performed using Hello mes-sages, LDP section establishment, and LDP messageexchange. Moreover, explicit LSPs can be specified.

MPLS (RSVP) Protocol (MD1230A-09)RSVP and RSVP-TE emulation satisfying the RFC2205 andRFC3209 standards can be performed by adding the option-al MD1203A-09 MPLS (RSVP) Protocol software.

RFC2889 Benchmarking Test (MD1230A-10)Benchmarking tests of LAN switching devices satisfying theRFC2889 standards can be performed by adding the option-al MD1230A-10 RFC2889 Benchmarking Test software. Thefollowing tests can be performed.

1) Fully meshed throughput, frame loss and forwarding rates2) Partially meshed one-to-many/many-to-one3) Partially meshed multiple devices4) Partially meshed unidirectional traffic5) Congestion control6) Forward pressure and maximum forwarding rate7) Address caching capacity8) Address learning rate9) Errored frames filtering10) Broadcast frame forwarding and latency

8/10/2019 129630_1_en

2/8

2

IPv6 Expansion (Option MD1230A-12)The following functions can be performed by adding theoptional MD1230A-12 IPv6 Expansion software.

1) ICMPv6 support2) MLD (Multicast Listener Discovery) Emulation3) Ping64) RFC2544 test using IPv65) IPv6 traffic monitoring and mapping6) Sending these IPv6 protocols in transmit streams:

IPv6 over IPv4 TCP/IPv6 UDP/IPv6 ICMPv6/IPv6 ICMPv6/IPv6 over IPv4 TCP/IPv6 over IPv4

UDP/IPv6 over IPv47) IPv6 related counters Send/Receive IPv6 packet count/rate Send/Receive ICMPv6(NA) packet count Send/Receive ICMPv6(NS) packet count Send/Receive ICMPv6 Echo Request packet count Send/Receive ICMPv6 Echo Reply packet count User-defined counter for IPv6

8) Filter and trigger for capture based on IPv69) Filter for user-defined counter based on IPv6

Protocol Addition and ExpansionThe following functions are added or expanded.1) Advertising 2 32 routes and maintaining 200 BGP Peers in

BGP-4 emulation2) Added IS-IS send and protocol decode functions3) Added OSPF protocol decode function4) Added MPLS (LDP/CR-LDP) protocol decode function5) Added MPLS (RSVP) protocol decode function6) IPv6 expanded header support for IPv6 send and protocol

decode functions

Support for 1000BASE-TThe new MU120112A Gigabit Ethernet module supports thestandard 1000BASE-T copper interface using the G0124A1000BASE-T GBIC optional accessory.

Note: For 1000BASE-T, the wire speed is 1 Gbps full duplex.

1000BASE-T GBIC

8/10/2019 129630_1_en

3/8

8/10/2019 129630_1_en

4/8

4

Functions Supported by Version 2.1

MU120101A MU120102A MU120103A -Function 10/100M Ethernet Gigabit Ethernet MU120106A

Module Module 2.5G/10G Modules

MD1230A-07 OSPF Protocol Option

MD1230A-08 MPLS (LDP/CR-LDP) Protocol Option

MD1230A-09 MPLS (RSVP) Protocol Option

MD1230A-10 RFC2889 Benchmarking Test Option X

MD1230A-12 IPv6 Expansion Option

MD1230A-13 XENPAK Test Option (including unframed BER test) N/A N/A N/A

BGP-4 emulation function expansion

IS-IS send/protocol decode function X X X

Protocol expansion OSPF protocol decode function X X Xor addition MPLS (LDP/CR-LDP) protocol decode function X X X

MPLS (RSVP) protocol decode function X X X

IPv6 expanded header support for IPv6 send and decode functions X X

1000BASE-T support N/A N/A

Monitor mode support X X X

Service disruption time measurement X X X

TCP/UDP port number increment function X X

BER measurementUnframed BER test X X

MD1230A-11 Packet BER Test Option X X

X: Supported functionN/A: Not applicable

8/10/2019 129630_1_en

5/8

8/10/2019 129630_1_en

6/8

6

MU120111A 10/100M Ethernet Module MU120112A Gigabit Ethernet Module

InterfaceOptical: 1000BASE-SX/LX/LH/ZX 1, Electrical: 1000BASE-T

Number of ports: 2Connector

Ports Optical: SC, Electrical: RJ-45Link speed: 1,000 Mbit/sDuplex mode: FullNegotiation: On/offFlow control: On/off

LED Link (10/100M), Tx /Collision, Rx/Error Link, Tx, Rx, Error

Connection mode When the mapping is Framed: Normal mode, Through mode, Monitor mode

Preamble length: 2 to 255 bytesMAC address: Static, increment, decrement, random (changeable parts specified in 4-bit units)VLAN tag 2: Static, increment, decrement, randomMPLS label 2: Up to 10 MPLS labels with fixed settings can be appended.Protocol editing:

IPv4, IPv6, TCP/IPv4, UDP/IPv4, IGMP/IPv4, ICMP/IPv4, RIP/UDP/IPv4, DHCP/UDP/IPv4, IPX, ARP, pause control, IS-ISFrame settingsThe following protocols are added by the MD1230A-12 option:

TCP/IPv6, UDP/IPv6, ICMPv6/IPv6, IPv6 over IPv4, ICMPv6/IPv6 over IPv4, TCP/IPv6 over IPv4, UDP/IPv6 over IPv4Data field

Can set any 4 parts in data field:All1s, all 0s, alternate1/0 (each bit, each 2 bits, each 4 bits, each byte, each 2 bytes, increment, decrement, random, userprogrammable, single PRBS9, time stamp, sequence number, test frame)

Frame length 18 to 10,000 bytes (settable as auto, fixed, increment, or random) 48 to 65,280 bytes (settable as auto, fixed, increment, or random)

Stream transport mode:Continuous, continuous burst, stop after this stream, nextstream, jump to stream, jump to stream for count (loop count:1 to 16,000,000, frame count per burst: 1 to 16,777,215, burstcount per stream: 1 to 16,777,215)

Interframe gap10BASE-T:

8,000 ns to 1,700 s, resolution of 800 ns settable as fixed,

random100BASE-TX:800 ns to 170 s, resolution of 80 ns settable as fixed, random

Stream settings Interburst gap10BASE-T:

8,000 ns to 1,700 s, resolution of 800 ns settable as fixed,random

100BASE-TX:800 ns to 170s, resolution of 80 ns settable as fixed, random

Interstream gap10BASE-T:

8,000 ns to 1,700 s, resolution of 800 ns settable as fixed,random

100BASE-TX:800 ns to 170 s, resolution of 80 ns settable as fixed, random

Number of streams 256 streams/por t

Collision, FCS error, alignment error, dribble bit error, undersize FCS error, undersize error, oversize error, fragments error,Error insertion error, oversize error, fragments error, oversize/FCS error, IPv4 oversize/FCS error, IPv4 header checksum error, TCP/UDP

header checksum error, TCP/UDP checksum error checksum error

Specifications

Stream transport mode:Continuous, continuous burst, stop after this stream, next

stream, jump to stream, jump to stream for count (loop count:1 to 16,000,000, frame count per burst: 1 to 16,777,215, burstcount per stream: 1 to 16,777,215)

Interframe gap64 ns to 120 s, resolution of 8 ns settable as fixed, random

Interburst gap64 ns to 120 s, resolution of 8 ns settable as fixed, random

Interstream gap64 ns to 120 s, resolution at of ns settable as fixed, random

Interface: 10BASE-T/100BASE-TXNumber of ports: 8Connector: RJ-45Link speed: 10 Mbit/s, 100 Mbit/sDuplex mode: Full, HalfNegotiation: On/offFlow control: On/off

8/10/2019 129630_1_en

7/8

7

MU120111A 10/100M Ethernet Module MU120112A Gigabit Ethernet Module

When Framed mapping is selected:Send & receive frame count/rate, send & receive byte count,send & receive data rate, capture trigger, capture filter, flowcontrol, send & receive ARP reply count, send & receive ARPrequest count, send & receive PING reply count, send & receivePING request count, QoS 0 - 7 count/rate, user-defined 1/2 andrate, send & receive IPv4 packet count/rate, receive TCP packetcount/rate, receive UDP packet count/rate, fragment, undersize,oversize, oversize & FCS error, FCS error, IPv4 header checksumerror, TCP checksum error, UDP checksum error, alignment error,dribble bit error, collision error, line error

CountersThe following counters are added by the MD1230A-12 option:

Send & receive IPv6 packet count/rate, send & receive ICMPv6Echo Request count, send & receive ICMPv6 Echo Replycount, send & receive ICMPv6 (NA) count, send & receiveICMPv6 (NS) count

The following counters are added by the MD1230A-11 option:Send & receive test frame count, sequence error, PRBS biterror count/rate, PRBS frame error count/rate

When Unframed mapping is selected:Bit error count/rate, pattern sync loss count, pattern sync lossseconds

Latency measurement Maximum, minimum, average values

Service disruption timemeasurement

Time measurement

Frame arrival timevariation measurement

Time resolution: 1 s, 10 s, 100 s, 1 ms, 10 ms, 100 ms, 1 s

With Packet BER Test (MD1230A-11 option) With Packet BER Test (MD1230A-11 option)Test pattern: Single PRBS9 Test pattern: Single PRBS9Error insertion: PRBS error Error insertion: PRBS error

With Unframed BER Test (supported on ports 1 and 5 only) With Unframed BER TestTest patterns: Test patterns:

BER measurement All 0s, All 1s, Alternate1/0, All 0s, All 1s, Alternate1/0,User defined 16 bytes, PRBS23, PRBS31 User defined 16 bytes, PRBS23, PRBS31, CJPAT, CRPATError insertion: PRBS error Error insertion: PRBS errorError insertion timing: Error insertion timing:

Single, rate (1E-3, 4, 5, 6, 7, 8, 9), Single, rate (1E-3, 4, 5, 6, 7, 8, 9),Programmable rate (9.9 E-3 to 1.0 E-10) Programmable rate (9.9 E-3 to 1.0 E-10)

QoS counter setting 8-level priority frame count using either the IEEE 802.1D VLAN tag user priority field or 3 bits of the RFC2474 DSCP (DiffServ) field

Capture buffer 8 Mbytes/port 32 Mbytes/port

Capture filterCapture filter condition settings for each port:

Destination MAC address, source MAC address, 128-bit pattern (settable bit length and offset) x 2, error conditions

Capture trigger condition settings for each port:Capture trigger Destination MAC address, source MAC address, 128-bit pattern (settable bit length and offset) x 2, error conditions, traffic over,

latency over, external trigger input

Protocol decodeEthernet, MPLS, VLAN, ARP, IPX, IPv4, ICMP for IPv4, ICMP for IPv6, IPv6, TCP, UDP, IGMP, RIP, BGP-4, DHCP, DVMRP, OSPFv2,MPLS LDP/CR-LDP, MPLS RSVP, IS-IS, IPv6 (expanded header)

Protocol emulationARP, ICPM for IPv4, IGMP, BGP-4, OSPF (MD1230A-07 option), MPLS LDP/CR-LDP (MD1230A-08 option),

MPLS RSVP (MD1230A-09 option), ICMP for IPv6 (MD1230A-12 option)

When Framed mapping is selected:Send & receive frame count/rate, send & receive byte count,send & receive data rate, capture trigger, capture filter, flowcontrol, send & receive ARP reply count, send & receive ARPrequest count, send & receive PING reply count, send & receivePING request count, QoS 0 - 7 count/rate, user-defined 1/2 andrate, send & receive IPv4 packet count/rate, receive TCP packetcount/rate, receive UDP packet count/rate, fragment, undersize,oversize, oversize & FCS error, FCS error, IPv4 header check-sum error, TCP checksum error, UDP checksum error, bytealignment error, line error

The following counters are added by the MD1230A-12 option:Send & receive IPv6 packet count/rate, send & receive ICMPv6Echo Request count, send & receive ICMPv6 Echo Replycount, send & receive ICMPv6 (NA) count, send & receiveICMPv6 (NS) count

The following counters are added by the MD1230A-11 option:Send & receive test frame count, sequence error, PRBS biterror count/rate, PRBS frame error count/rate

When Unframed mapping is selected:Bit error count/rate, pattern sync loss count, pattern sync lossseconds

1: 1000BASE-SX/LX/LH/ZX/T can be selected by changing the GBIC module.2: The VLAN tag and MPLS labels cannot be used simultaneously.

8/10/2019 129630_1_en

8/8

Ordering Information

Model/Order No. NameOption

MD1230A-07 OSPF ProtocolMD1230A-08 MPLS (LDP/CR-LDP) ProtocolMD1230A-09 MPLS (RSVP) ProtocolMD1230A-10 RFC2889 Benchmarking TestMD1230A-11 Packet BER TestMD1230A-12 IPv6 ExpansionMD1230A-13 XENPAK Test

Plug-in modulesMU120111A 10/100M Ethernet ModuleMU120112A Gigabit Ethernet Module 1

Model/Order No. NameMaintenance service

MU120111A-90 Extended three year warranty serviceMU120112A-90 Extended three year warranty service

Optional accessoriesG0105A GBIC SX 850 nm 2G0106A GBIC LX 1310 nm 2G0107A GBIC LH 1310 nm 2G0108A GBIC ZX 1550 nm 2G0124A GBIC T (1000BASE-T) 2

The MD1230A family includes these newly added products and options.Refer to the separate MD1230A datasheet regarding existing MD1230A family products.

1: MU120112A requires two GBIC modules (sold separately).2: GBIC modules are sold individually. MU120112A can accommodate two GBIC interfaces.

ANRITSU CORPORATION5-10-27, Minamiazabu, Minato-ku, Tokyo 106-8570, JapanPhone: +81-3-3446-1111Telex: J34372Fax: +81-3-3442-0235

U.S.A.ANRITSU COMPANYNorth American Region Headquarters1155 East Collins Blvd., Richardson, TX 75081, U.S.A.Toll Free: 1-800- ANRITSU (267-4878)Phone: +1-972-644-1777Fax: +1-972-671-1877 CanadaANRITSU ELECTRONICS LTD.700 Silver Seven Road, Suite 120, Kanata,ON K2V 1C3, CanadaPhone: +1-613-591-2003Fax: +1-613-591-1006 BrasilANRITSU ELETRNICA LTDA.Praia de Botafogo 440, Sala 2401 CEP 22250-040,Rio de Janeiro, RJ, BrasilPhone: +55-21-5276922Fax: +55-21-537-1456 U.K.ANRITSU LTD.200 Capability Green, Luton, Bedfordshire LU1 3LU, U.K.Phone: +44-1582-433200Fax: +44-1582-731303

GermanyANRITSU GmbHGrafenberger Allee 54-56, 40237 Dsseldorf, GermanyPhone: +49-211-96855-0Fax: +49-211-96855-55 FranceANRITSU S.A.9, Avenue du Qubec Z.A. de Courtabuf 91951 LesUlis Cedex, FrancePhone: +33-1-60-92-15-50Fax: +33-1-64-46-10-65 ItalyANRITSU S.p.A.Via Elio Vittorini, 129, 00144 Roma EUR, ItalyPhone: +39-06-509-9711Fax: +39-06-502-24-25 SwedenANRITSU ABBotvid Center, Fittja Backe 1-3 145 84 Stockholm,SwedenPhone: +46-853470700Fax: +46-853470730 SpainANRITSU ELECTRNICA, S.A.Europa Empresarial Edificio Londres, Planta 1, Oficina6 C/ Playa de Liencres, 2 28230 Las Rozas. Madrid,SpainPhone: +34-91-6404460Fax: +34-91-6404461

SingaporeANRITSU PTE LTD.10, Hoe Chiang Road #07-01/02, Keppel Towers,Singapore 089315Phone: +65-6282-2400Fax: +65-6282-2533

Hong KongANRITSU COMPANY LTD.Suite 719, 7/F., Chinachem Golden Plaza, 77 ModyRoad, Tsimshatsui East, Kowloon, Hong Kong, ChinaPhone: +852-2301-4980Fax: +852-2301-3545 KoreaANRITSU CORPORATION14F Hyun Juk Bldg. 832-41, Yeoksam-dong,Kangnam-ku, Seoul, KoreaPhone: +82-2-553-6603Fax: +82-2-553-6604 5 AustraliaANRITSU PTY LTD.Unit 3/170 Forster Road Mt. Waverley, Victoria, 3149,AustraliaPhone: +61-3-9558-8177Fax: +61-3-9558-8255 Taiwan

ANRITSU COMPANY INC.7F, No. 316, Sec. 1, NeiHu Rd., Taipei, TaiwanPhone: +886-2-8751-1816Fax: +886-2-8751-1817

Specifications are subject to change without notice.

Catalog No. MU120111A/120112A-E -A -3 -(1.00) Printed in Japan 2003-2 30ddc/M

030123