1430 mcs technical specifications · 2020. 10. 27. · section - 1 5 1430 mcs, technical...

74
IOWA MOLD TOOLING CO., INC. P.O. Box 189 Garner, IA 50438 Tel: 641.923.3711 Fax: 641.923.2424 www.imt.com 1430 MCS Technical Specifications Manual # 99906329 Revised 02-16-2021 Copyright © 2021 Iowa Mold Tooling Co., Inc. All rights reserved No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of Iowa Mold Tooling Co., Inc. Iowa Mold Tooling Co., Inc. is an Oshkosh Corporation Company

Upload: others

Post on 05-Mar-2021

17 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

IOWA MOLD TOOLING CO., INC.

P.O. Box 189Garner, IA 50438Tel: 641.923.3711

Fax: 641.923.2424www.imt.com

1430 MCS Technical

Specifications

Manual # 99906329

Revised 02-16-2021

Copyright © 2021 Iowa Mold Tooling Co., Inc.All rights reserved

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording or otherwise without the prior written permission of Iowa Mold Tooling Co., Inc.

Iowa Mold Tooling Co., Inc. is an Oshkosh Corporation Company

Page 2: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

ii

1430 MCS - Manual # 99906329

Page 3: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

iii

1430 MCS - Manual # 99906329

Table of Contents

Section - 1 - Specifications 1

1430 MCS - Specifications ............................................................................................................................21430 MCS - Specifications, Metric .................................................................................................................5

Section - 2 - Lifting Capacities 9

1430 MCS-K1, Lifting Capacity Chart ..........................................................................................................101430 MCS-K2, Lifting Capacity Chart .......................................................................................................... 111430 MCS-K3, Lifting Capacity Chart ..........................................................................................................121430 MCS-K4, Lifting Capacity Chart ..........................................................................................................131430 MCS-K5, Lifting Capacity Chart ..........................................................................................................141430 MCS-K6, Lifting Capacity Chart ..........................................................................................................151430 MCS - K1-K6, Lifting Capacity ...........................................................................................................16

Section - 3 - Dimension Sketches 17

Lifting capacity with winch ............................................................................................................................181430 MCS - Dimension Sketch ...................................................................................................................191430 MCS - Slewing Radius ........................................................................................................................201430 MCS - Dimension Sketch, Truck-Mounted Loader ..............................................................................211430 MCS - Lifting Height at Column ..........................................................................................................221430 MCS - Dimension Sketch, Fixed Stabilizer Legs ................................................................................231430 MCS - Dimension Sketch, Fixed Stabilizer Legs ................................................................................241430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 20°- 60°(Manual) ..............................................251430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 20°- 60°(Manual) ..............................................261430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 180°(Manual & Hydraulic) ...................271430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 180°(Manual & Hydraulic) ...................281430 MCS - Dimension Sketch Top Seat, RC & HC Linear .........................................................................291430 MCS - Dimension Sketch, Top Seat (Danfoss X) ................................................................................301430 MCS - Dimension Sketch, Top Seat (HC X) ........................................................................................311430 MCS - Dimension Sketch, Ladder for TS ............................................................................................321430 MCS - Stowed in Truck Body ..............................................................................................................331430 MCS - Dimension Sketch for Connecting Link ....................................................................................341430 MCS - Technical Data, Winch .............................................................................................................351430 MCS - Dimension Sketch, Winch ........................................................................................................361430 MCS - Dimension sketch, Stand-Up Platform (STD & Valve Control) ................................................371430 MCS - Dimension Sketch, Internal Hose Routing ...............................................................................38

Section - 4 - Hydraulic Drawings 39

1430 MCS - Pressure Setting Diagram, Manual ..........................................................................................401430 MCS - Pressure Setting Diagram, Fixed Flow Pump & Danfoss (Man) ..............................................411430 MCS - Danfoss, Single-Circuit Fixed 6 FCTS. RC (2 EXV: Grab + Rotator) .....................................421430 MCS - Danfoss, single-circuit variable6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator) .........431430 MCS - Hydrocontrol, single-circuit fixed 6 fcts. Std./HS, std./HS dir. valve contr. HDL (2 EXV: Grab + Rotator) ........................................................................................................................................................441430 MCS - Hydrocontrol, single-circuit fixed 6 fcts. RC med HDL (2 EXV: Grab + Rotator) ......................451430 MCS - Hydraulic Diagram - Stablilizer circuit – 2 fcts. ........................................................................461430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. ........................................................................471430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. RC ..................................................................481430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts. ...........................................491430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts. RC .....................................501430 MCS - Lubrication instructions ............................................................................................................511430 MCS - Lubrication instructions ............................................................................................................52

Page 4: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

This page left intentionally blank

iv

1430 MCS - Manual # 99906329

1430 MCS - Change of slewing area ...........................................................................................................551430 MCS - Replacement of hydraulic hoses in column .............................................................................601430 MCS - By-pass hose routing for emergency repair .............................................................................64

Page 5: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 1 1 1430 MCS, Technical Specifications

1430 MCS - Manual # 99906329

Section - 11430 MCS, Technical Specifications

Page 6: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 1 2 1430 MCS, Technical Specifications

1430 MCS - Manual # 99906329

1430 MCS - Specifications

Performance Unit K1 K2 K3 K4 K5 K6Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3

Load moment ft-lb 97446 93837 90949 88062 85175 83009Hydraulic reach ft 20’8” 27’7” 34’5” 42’0” 49’3” 56’9”Hydraulic telescopic movement ft 6’3” 12’9” 19’8” 27’0” 34’1” 41’3”

Lifting capacity, hydraulic

lb-ft 6945-14’1” 6658-14’1” 6327-14’5” 6019-14’9” 5732-15’2” 5490-15’2”

lb-ft 4784-20’4” 4519-20’8” 4211-20’8” 3924-21’0” 3682-21’4” 3461-21’8”

lb-ft 3395-27’2” 3086-27’2” 2822-27’7” 2579-27’11” 2381-28’3”

lb-ft 2447-34’1” 2161-34’5” 1940-34’9” 1720-35’1”

lb-ft 1764-41’8” 1521-42’0” 1323-42’4”

lb-ft 1279-48’11” 1080-49’3”

lb-ft 926-56’5”

Lifting Capacities, Manual Extensions

lb-ft2535-34’1” 1852-41’8” 1345-49’3” 1014-56’5” 750-64’4”

lb-ft1962-41’4” 1433-49’3” 1080-57’1”‘ 816-64’4”

lb-ft1521-49’3” 1190-56’9” 882-64’8”

Slewing torque, gross lb-ft 3956Slewing angle ° 400Max. heel at max. load moment ° 5

Slewing speed °/s 24

Dimensions Unit K1 K2 K3 K4 K5 K6Height above chassis ft-in 7’ 4”Width ft-in 8’ 2”Width with extra valves (int. hose routing) ft-in 8’ 3”Length, no extra valves ft-in 2’ 7’Length, with extra valves (hose guides) ft-in 3’ 1”Length, with extra valves (int. hose routing) ft-in 2’ 7”Stabilizer spread, S1 (standard) ft-in 15’ 1”Stabilizer spread, S2 ft-in 18’ 3”Stabilizer spread, D ft-in 21’ 2”

1) Weights ± 5% because of tolerances for plate thickness

Page 7: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 1 3 1430 MCS, Technical Specifications

1430 MCS - Manual # 99906329

1430 MCS - Specifications - continued

Weights, basic loader Unit K1 K2 K3 K4 K5 K6Standard loader 1), excl. stabilizers lb 2888 3197 3505 3803 4068 4277Stabilizers, S1 fixed lb 441Stabilizers, S1 swing-up lb 452Stabilizers, S1 hydr. swing-up lb 474Stabilizers, S2 fixed lb 518Stabilizers, S2 swing-up lb 529Stabilizers, S2 hydr. swing-up lb 551Stabilizers, D fixed lb 661Stabilizers, D swing-up lb 561Stabilizers, D hydr. swing-up lb 694Mounting kit, 4 bolts lb 121Mounting kit, 8 bolts lb 132Tank, excl. oil (fitted on loader) lb 99

Manual extensions lb —187165143

16514399

1439988

9988

88

Oil in loader lb 55 66 77 88 99 99

Weights, equipment Unit K1 K2 K3 K4 K5 K6Stand-up controls (HS), std. lb 132Stand-up controls (HS), direct valve control lb 154Top seat (TS) lb 198Top seat, ladder lb 441 extra valve, hose guides lb 88 121 143 165 187 2091 extra valve, int. hose routing lb 165 165 165 176 176 1872 extra valves, hose guides lb 132 165 198 231 265 2982 extra valves, int. hose routing lb 287 287 287 309 320 331Winch (1.5 t), single snatch block lb 386 397

Winch (1.5 t), double snatch block lb 375 386

Winch (2.5 t), single snatch block lb 441 452

Winch (2.5 t), double snatch block lb 430 441

High-pressure filiter lb 15

Oil cooler lb 55

Max. load on stabilizer (per stab. cylinder) Unit K1 K2 K3 K4 K5 K6S1, fixed ft-lb

62693

S1, swing-up ft-lbS1, hyd swing-up ft-lbS2, fixed ft-lbS2, Swing-up ft-lbS2, hyd swing-up ft-lbD, fixed ft-lb

50154D, swing-up ft-lbD, hyd swing-up ft-lb

Page 8: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 1 4 1430 MCS, Technical Specifications

1430 MCS - Manual # 99906329

1430 MCS Technical Specifications - Continued

Power consumption / oil capacity Unit K1 K2 K3 K4 K5 K6Working pressure psi 4786Tank capacity (fitted on loader) gal 24Max. pump performance, Hydrocontrol 1-circuit g/min 11.9

Max. pump performance, Danfoss fixed flow g/min 18.5Max. pump performance, Danfoss variable g/min 26.4

Page 9: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 1 5 1430 MCS, Technical Specifications

1430 MCS - Manual # 99906329

1430 - Specifications, Metric

Performance Unit K1 K2 K3 K4 K5 K6Loading group (EN12999) H1/B3 H1/B3 H1/B3 H1/B3 H1/B3 H1/B3

Load moment tm 13.5 13 12.6 12.2 11.8 11.5Hydraulic reach m 6.3 8.4 10.5 12.8 15.0 17.3Hydraulic telescopic movement mm 1930 3940 6040 8230 10390 12580

Lifting capacity, hydraulic

kg-m 3150-4.3 3030-4.3 2870-4.4 2730-4.5 2600-4.6 2490-4.6

kg-m 2170-6.2 2040-6.3 1910-6.3 1780-6.4 1670-6.5 1570-6.6

kg-m 1540-8.3 1400-8.3 1280-8.4 1170-8.5 1080-8.6

kg-m 1110-10.4 980-10.5 880-10.6 780-10.7

kg-m 800-12.7 690-12.8 600-12.9

kg-m 580-14.9 490-15.0

kg-m 420-17.2

Lifting Capacities, Manual Extensions

kg-m1150-10.4 840-12.7 610-15.1 460-17.2 340-19.6

kg-m890-12.6 650-15.0 490-17.4 370-19.6

kg-m690-15.0 540-17.3 400-19.7

Slewing torque, gross kNm 17.6Slewing angle ° 400Max. heel at max. load moment ° 5

Slewing speed °/s 24

Dimensions Unit K1 K2 K3 K4 K5 K6Height above chassis mm 2250Width mm 2500Width with extra valves (int. hose routing) mm 2535Length, no extra valves mm 825Length, with extra valves (hose guides) mm 950Length, with extra valves (int. hose routing) mm 825Stabilizer spread, S1 (standard) mm 4615Stabilizer spread, S2 mm 5900Stabilizer spread, D mm 6470

1) Weights ± 5% because of tolerances for plate thickness

Page 10: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 1 6 1430 MCS, Technical Specifications

1430 MCS - Manual # 99906329

1430 MCS Specifications - Metric, continued

Weights, basic loader Unit K1 K2 K3 K4 K5 K6Standard loader 1), excl. stabilizers kg 1310 1450 1590 1725 1845 1940Stabilizers, S1 fixed kg 200Stabilizers, S1 swing-up kg 205Stabilizers, S1 hydr. swing-up kg 215Stabilizers, S2 fixed kg 235Stabilizers, S2 swing-up kg 240Stabilizers, S2 hydr. swing-up kg 250Stabilizers, D fixed kg 300Stabilizers, D swing-up kg 300Stabilizers, D hydr. swing-up kg 315Mounting kit, 4 bolts kg 55Mounting kit, 8 bolts kg 60Tank, excl. oil (fitted on loader) kg 45

Manual extensions kg —857565

756545

654540

4540

40

Oil in loader kg 25 30 35 40 45 45

Weights, equipment Unit K1 K2 K3 K4 K5 K6Stand-up controls (HS), std. kg 60Stand-up controls (HS), direct valve control kg 70Top seat (TS) kg 90Top seat, ladder kg 201 extra valve, hose guides kg 40 55 65 75 85 951 extra valve, int. hose routing kg 75 75 75 80 80 852 extra valves, hose guides kg 60 75 90 105 120 1352 extra valves, int. hose routing kg 130 130 130 140 145 150Winch (1.5 t), single snatch block kg 175 180

Winch (1.5 t), double snatch block kg 170 175

Winch (2.5 t), single snatch block kg 200 205

Winch (2.5 t), double snatch block kg 195 200

High-pressure filiter kg 7

Oil cooler kg 25

Max. load on stabilizer (per stab. cylinder) Unit K1 K2 K3 K4 K5 K6S1, fixed kN

85

S1, swing-up kNS1, hyd swing-up kNS2, fixed kNS2, Swing-up kNS2, hyd swing-up kND, fixed kN

68D, swing-up kND, hyd swing-up kN

Page 11: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 1 7 1430 MCS, Technical Specifications

1430 MCS - Manual # 99906329

1430 Specifications - Metric, continued

Power consumption / oil capacity Unit K1 K2 K3 K4 K5 K6Working pressure Bar 330Tank capacity (fitted on loader) L 90Max. pump performance, Hydrocontrol 1-circuit L/min 45

Max. pump performance, Danfoss fixed flow L/min 70Max. pump performance, Danfoss variable L/min 100

Minimum Chassis SpecsFront Axle Rating (GAWR) 12,000 (5443 kg)Rear Axle Rating (GAWR) 21,000 (9525 kg)Resistance to Bending Moment 1,400,000 (16134 kg-m)

Page 12: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

This page left intentionally blank

8

1430 MCS - Manual # 99906329

Page 13: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 2 9 1430 MCS Load Capacity Charts

1430 MCS - Manual # 99906329

Section - 21430 MCS Load Capacity Charts

Page 14: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 2 10 1430 MCS Load Capacity Charts

1430 MCS - Manual # 99906329

1430 MCS-K1, Lifting Capacity Chart

MODEL 1430 MCS K1

Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.

NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN

VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT

REVISIONSREV CN DESCRIPTION DATE BY

IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438

TEL: 515-923-3711 FAX: 515-923-2424

TECH PUBS GENERATED DRAWING

DRAWN BY

APPROVED BY DATE

DATE SCALETITLE

SIZE DWG NO

SHT OF

A

FULL5/07/2018 DECAL- CP1430 MCS K1

BKS

70490149

70490149(2m) (4m) (6m)6’ 6” 13’ 1” 19’ 7”

0

(2m)

(4m)

(6m)

(8m)

6’ 6”

13’ 1”

19’ 7”

26’ 3”

0

(1m) (3m) (5m) (7m)3’ 3”

(1m)3’ 3”

9’ 11”

(3m)9’11”

16’ 5”

(5m)16’ 5”

23’ 0”

(7m)23’ 0”

(9m)29’ 5”

69453150 2170

lb

kg

110235000

4784

Page 15: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 2 11 1430 MCS Load Capacity Charts

1430 MCS - Manual # 99906329

1430 MCS-K2, Lifting Capacity Chart

MODEL1430 MCS K2

Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.

NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN

VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT

REVISIONSREV CN DESCRIPTION DATE BY

IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438

TEL: 515-923-3711 FAX: 515-923-2424

TECH PUBS GENERATED DRAWING

DRAWN BY

APPROVED BY DATE

DATE SCALETITLE

SIZE DWG NO

SHT OF

A

FULL5/07/2018 DECAL- CP1430 MC K2

BKS

70490150

70490150(2m) (4m) (6m) (8m)6’ 6” 13’ 1” 19’ 8” 26’ 3”

0

(2m)

(4m)

(6m)

(8m)

(10m)

(12m)

6’ 6”

13’ 1”

19’ 8”

26’ 3”

32’ 10”

39’ 4”

0

(1m) (3m) (5m) (7m) (9m)3’ 3”

(1m)3’ 3”

9’ 11”

(3m)9’ 11”

16’ 5”

(5m)16’ 5”

23’ 0”

(7m)23’ 0”

29’ 6”

(9m)29’ 6”

(11m)36’ 1”

66583020

45192050

33951540

lb

kg

105824800

Page 16: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 2 12 1430 MCS Load Capacity Charts

1430 MCS - Manual # 99906329

1430 MCS-K3, Lifting Capacity Chart

MODEL 1430 MCS K3

Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.

NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN

VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT

REVISIONSREV CN DESCRIPTION DATE BY

IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438

TEL: 515-923-3711 FAX: 515-923-2424

TECH PUBS GENERATED DRAWING

DRAWN BY

APPROVED BY DATE

DATE SCALETITLE

SIZE DWG NO

SHT OF

A

FULL5/07/2018 DECAL- CP1430 MCS K3

BKS

70490151

70490151(2m) (4m) (6m) (8m) (10m)

(11m)

(13m)

6’ 6” 13’ 1” 19’ 8” 26’ 3” 32’10”

42’ 8”

0

(2m)

(4m)

(6m)

(8m)

(10m)

(12m)

6’ 6”

13’1”

19’ 7”

26’3”

32’10”

39’ 4”

0

(1m) (3m) (5m) (7m) (9m)3’ 3”

(1m)3’ 3”

9’ 11”

(3m)9’ 11”

16’ 5”

(5m)16’ 5”

23’0”

(7m)23’0”

29’ 6”

(9m)29’ 6”

36’ 1”

(11m)36’ 1”

63272870

42111910

30861400 1110

lb

kg

2447

105824800

Page 17: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 2 13 1430 MCS Load Capacity Charts

1430 MCS - Manual # 99906329

1430 MCS-K4, Lifting Capacity Chart

39241780

28221280

2161980

1764800

60192730

99214500

MODEL 1430 MCS K4

Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.

(2m) (4m) (6m) (8m) (10m)(11m)6’ 6” 13’ 2” 19’ 8” 26’ 3” 32’ 10”

0(1m) (3m) (5m) (7m) (9m)

3’ 3” 9’ 11” 16’ 5” 23’ 0” 29’ 6” 36’ 1”(13m)42’ 8”

(12m)39’ 4”

(14m)44’ 11”

(16m)52’ 6”

(2m)

(4m)

(6m)

(8m)

(10m)

(12m)

6’ 6”

13’ 1”

19’ 8”

26’ 3”

32’ 10”

39’ 4”

0

NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN

VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT

REVISIONSREV CN DESCRIPTION DATE BY

IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438

TEL: 515-923-3711 FAX: 515-923-2424

TECH PUBS GENERATED DRAWING

DRAWN BY

APPROVED BY DATE

DATE SCALETITLE

SIZE DWG NO

SHT OF

A

FULL5/07/2018 DECAL- CP1430 MCS K4

BKS

70490152

70490152

lb

kg

Page 18: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 2 14 1430 MCS Load Capacity Charts

1430 MCS - Manual # 99906329

1430 MCS-K5, Lifting Capacity Chart

Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.

NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN

VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT

REVISIONSREV CN DESCRIPTION DATE BY

IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438

TEL: 515-923-3711 FAX: 515-923-2424

TECH PUBS GENERATED DRAWING

DRAWN BY

APPROVED BY DATE

DATE SCALETITLE

SIZE DWG NO

SHT OF

A

FULL5/07/2018 DECAL- CP1430 MCS K5

BKS

70490153

70490153(2m) (4m) (6m) (8m) (10m) (12m) (14m) (16m)6’ 6” 13’ 1” 19’ 8” 26’ 3” 32’ 10” 39’ 4” 45’ 11” 52’ 6”0

(2m)

(4m)

(6m)

(8m)

(10m)

(12m)

(14m)

(16m)

(18m)

6’ 6”

13’ 1”

19’ 8”

26’ 3”

32’ 10”

39’ 4”

45’ 11”

52’ 6”

59’ 0”

0

1279580

57322600

36821670

25791170

1940880

1521690

lb kg

MODEL1430 MCS K5

97004400

Page 19: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 2 15 1430 MCS Load Capacity Charts

1430 MCS - Manual # 99906329

1430 MCS-K6, Lifting Capacity Chart

Limit working loads to those shown. Deduct the weightof load handling devices.El peso propio (tara) de los dispositivos demanipulación de cargas es parte de la cargalevantada y se debe descontar de la capacidad nominal.

NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWN

VENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT

REVISIONSREV CN DESCRIPTION DATE BY

IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438

TEL: 515-923-3711 FAX: 515-923-2424

TECH PUBS GENERATED DRAWING

DRAWN BY

APPROVED BY DATE

DATE SCALETITLE

SIZE DWG NO

SHT OF

A

FULL5/07/2018 DECAL- CP1430 MCS K6

BKS

70490154

lb kg

70490154

54902490

34611570

23811080

1720780

1323600

1080490

926420

(2m)

(2m)

(4m)

(6m)

(8m)

(10m)

(12m)

(14m)

(16m)

(18m)

(20m)

(4m) (6m) (8m) (10m) (12m) (14m) (16m) (18m)

6’ 6”

6’ 6”

13’ 1”

13’ 1”

19’ 8”

19’ 8”

26’ 3”

26’ 3”

32’ 10”

32’ 10”

39’ 4”

39’ 4”

45’ 11”

45’11”

52’ 6”

52’6”

59’ 0”

59’ 0”

65’ 7”

0

0

MODEL1430 MCS K6

94804300

Page 20: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 2 16 1430 MCS Load Capacity Charts

1430 MCS - Manual # 99906329

1430 MCS - K1-K6, Lifting Capacity

K5

K4

K3

2579

K2

K1

FT 14’1” 20’4”47846945

1521

LB

M21703150KG

10145732 1940LBFT

6658 15211962 LBFT

25353395

1279

4519

M 4,3 6,3 8,3 10,4 12,6 15,03020 690098 KG 115015402050

11906327 1433 1852LBFT

244730864211

M 4,4 6,3 8,3 10,4 12,7 15,0 17,3 5402870 650 840KG 111014001910

882

400

3924 1080 13456019 1764 2161LBFT

2822

M 4,5 6,4 8,4 10,5 12,7 15,0 17,4 19,7 1780 490 6102730 800 980KG 1280

8163682

1170 690 4602600 880KG 580 M 4,6 6,5 8,5 10,6 12,8 14,9 17,2 19,6

3701670

LBFT

5490 3641 2381 1720 1323 1080 926 750

M 4,6 6,6 8,6 10,7 12,9 15,0 17,2 19,6KG 2490 1570 1080 780 600 490 420 340

K6

LIFTING CAPACITY WITH MANUAL EXTENSIONS

LIFTING CAPACITY WITHOUT MANUAL EXTENSIONS

4,3

14’1”

14’5”

14’9”

15’2”

15’2” 21’8” 28’3” 35’1” 42’4” 49’3” 56’5” 64’4”

21’4” 27’11” 34’9” 42’0” 48’11” 56’5” 64’4”

21’0” 27’7” 34’5” 41’8” 49’3” 57’1” 64’8”

20’8” 27’2” 34’1” 41’8” 49’3” 56’9”

20’8” 27’2” 34’1” 41’4” 49’3”

6,2

Page 21: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 17 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

Section - 31430 MCS, Dimension Drawings

Page 22: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 18 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

Lifting capacity with winch

Hydraulic hoist type

65°

90°

Not recommended workning angle.

Dinamic S 25 Brevini 2500

Dinamic P9E

Dinamic P15E

Hydraulic hoist type

Dinamic S 25 Brevini 2500

Dinamic P9E

Dinamic P15E

MAXW MAXWMAXWD MAXWD

1500 kg 3000 kg

2500 kg 5000 kg

6400 kg3200 kg

3307 lb

5512 lb

7055 lb

6614 lb

11023 lb

14110 lb

Page 23: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 19 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch

73 2.9”

28,5

1953

6

’5”

2162

7’2

2715

8’

11”

225

0

7’5”

1250 4’1”

2500 8’2”

290 CL CHASSIS

76 (TYP.)

4726 15’6”

381

2502

8

’2”

950

825

A

TOP CHASSISA-A

TOP CHASSIS TOP CHASSIS

A 3”

Metric=Millimeters

11.5”

37.4”

34.5”

15”

Page 24: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 20 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Slewing Radius

R380

R470 18.5”

R440 17.3”

R600 23.7”

1745

5’

9”

2075

6’

10”

2095

6’

11‘

2375

7’

10”

10°

TOP CHASSIS

15”

Page 25: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 21 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Truck-Mounted Loader

Max.32 Max.32

Max.6.3”Max.160

26

80

7”185

1.5”

40

28”

717

14”

357

Min.580Min 23”

Max.1060Max.3’6”

Min.2’11”/Max.3’5”

Min.900/Max.1040

38 38

Min

.200

/Max

.560

Min

.7.8

” Max

.22”

140

1)

1)1)

See note 2)

Mounting kit 8 x M24x2 bolts

Mounting kit 4 x M30x2 bolts

Notes:

1) Values dictated by strength considerations.

2) Drill hole when assembling

3) As regards installation - please see HMF Installation Manual

4) Mounting kits or spare parts - please see the Spare Parts Catalogue of the individual loader

CL CHASSIS

1.2” 1.2”

28”

717

14”

357

1.5” 1.5”

Page 26: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 22 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

70399472

Model 40/275 K5FJ1000 K3

25555630 19504300 13602995 10202245

6'(1.83 m)0CENTERLINE 18'(5.49 m)12'(3.66 m) 30'(9.14 m)24'(7.32 m) 42'(12.80 m)36'(10.97 m) 54'(16.46 m)48'(14.63 m) 66'(20.12 m)60'(18.29 m) 72'(21.95 m)

0MOUNTING SURFACE

6'(1.83 m)

12'(3.66 m)

18'(5.49 m)

24'(7.32 m)

30'(9.14 m)

36'(10.97 m)

42'(12.80 m)

48'(14.63 m)

54'(16.46 m)

60'(18.29 m)

72'(21.95 m)

66'(20.12 m)

84'(25.60 m)

78'(21.95 m)

80°

65°

45°

45°

20º30°

KGLB

11652565 10502315 9552105 8701915

14303150 12752810 11552545 10502315

18604100 16403615 14653230 11402510

29506500 22705005 15953515 12002645

29506500 23155100 16253580 12272705

15953515

29506500 2950650021054640

29506500

23155100

16253580

12202690

NOTES:MATERIAL: .005" VELVET FINISH LEXANADHESIVE: 3M 468 HI-PERFORMANCE APPLIED AFTER SCREENINGSIZE: 8" WIDE X 10.50” HIGHCOLORS: BLACK AND WHITE AS SHOWNVENDOR: CREATIVE SCREEN PRINT (CRE10) OR EQUIVALENT

REVISIONSREV ECO DESCRIPTION DATE BY

70399472

IOWA MOLD TOOLING CO., INCBOX 189, GARNER, IA 50438TEL: 515-923-3711 FAX: 515-923-2424TECH PUBS GENERATED DRAWING

DRAWN BY

APPROVED BY DATEDATE SCALETITLE SIZE DWG NO SHT OFKJB AFULL12-19-13 DECAL- MODEL 40/275K5 / FJ1000 K3

A 9000 KJB12/19/2013Changed model description

1430 MCS - Lifting Height at Column

H1K1 9’0”

K2 8’10”

K3 8’7”

K4 8’4”

K5 8’0”

K6 7’8”

7’3”

2,2m H

1

R=1m

TOP CHASSIS

H1K1 2,76m

K2 2,71m

K3 2,62m

K4 2,53m

K5 2,44m

K6 2,35m

Page 27: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 23 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Fixed Stabilizer Legs

A 2’6” 2’11” 3’2”

20”

520

A A20

”20

20”

520

290 CL CHASSIS

5’4”1625

23407’8” 5’4”1625559018’4”

290 CL CHASSIS

3’8”1137

3’8”1137

23407’8”

461415’1”

A20

”52

0

A20

”52

0

6’9”2065

23407’8” 6’9”2065647021’2”

520

520

AA 290 CL CHASSIS

TOP CHASSIS

TOP CHASSIS

TOP CHASSIS

A 777 877 977

11”

11”

11”

Page 28: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 24 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Fixed Stabilizer Legs

27”

677

440

17”

4610 / 5590 / 6470

15’1” / 18’4” / 21’3”

195

290

360

357

TOP CHASSIS

Stabilizer cylinder, C80-440

Page 29: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 25 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 20°- 60°(Manual)

290 11”

CL CHASSIS

5’4”1625

23227’7” 5’4”1625557218’3”

A20

”52

0

A20

”52

0

290 11”

CL CHASSIS

A20

”52

0

A20

”52

0

7’7”3’8”1137

3’8”113715’1”

23214595

6’9”2065

20”

520

23227’7” 6’9”2065

20”

520

645221’2”

AA

290 11”

CL CHASSIS

Type R-20° (Obsolete)

Type R-60°

A

3’2”

3’1”

2’10”

2’9”

2’6”

2’6”

TOP CHASSIS

TOP CHASSIS

TOP CHASSIS

AType R-20° (Obsolete)

Type R-60°

A

971

963

871

863

771

763

A

Page 30: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 26 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 20°- 60°(Manual)

Type R-60°

BC C

B30°60°

20°

D

4”

4”

95

95

195290

360357Type R-60°

Type R-20° (Obsolete)

C

B

36”22”

33”20”

29”18”

16”15”13”D

C

B

918565

831515

744465

412378344D

14” 14.1”11”

7.7”

Page 31: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 27 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 180°(Manual & Hydraulic)

290 11”

CL CHASSIS

A16

”41

8

A16

”41

8

6’9”1625

2320 6’9”16255570

7’7”

21’9”

18’3”

290 11”

CL CHASSISA20

”52

0

A20

”52

0

23197’7”3’8”1137

3’8”1137459315’1”

6’9”2065 6450

2320 6’9”2065

418

16”

16”

A A41

8

29011”

CL CHASSIS

TOP CHASSIS

TOP CHASSIS

A 35” 37” 43” A 881 981 1081

Page 32: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 28 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Swing-up Stabilizer Legs 180°(Manual & Hydraulic)

B

6553 63

150

95

195

290

357

360

TOP CHASSIS

B 31” 34” 38” B 775 875 975

357 14” 360 14.1”290 11”195 7.7”

95 3.7”65 2.5”53 2.1”63 2.5”

mm IN

mm IN

Page 33: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 29 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch Top Seat, RC & HC Linear

2’7”785

8702’10”

1’7”475

5’0” 1530

1’7”

490

7’8”

2330

R10

20

R10

80

3’11

”12

00

Page 34: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 30 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Top Seat (Danfoss X)

800

2’7”890

2’11”

6152’0”

4’8”

1410

1’8”

500

2220

7’3”

200.7”

4’10

”14

80

R11

90

R11

40

Page 35: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 31 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Top Seat (HC X)

2’5”735

2’8”825

1’11”585

4’8”

1410

1’4”

400

R11

35

R119

5

Page 36: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 32 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Ladder for TS

4’0”

1230

1’9”

520

TOP CHASSIS

Notes:

1) Ladder cannot be used for TS RC

2) There is no access to the top seat when the loader is in stowing position

Page 37: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 33 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Stowed in Truck Body

2322

2432

1333

15°

2091

TOP CHASSIS

TOP CHASSIS

7’ 6

8’ 0

6’ 9

”4’ 4

Page 38: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 34 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch for Connecting Link

The following design is recommended so the connecting link can swing sufficiently when using the equipment or when stowing and/or folding in the truck body.

The connecting link must be able to move freely at an angle of 35° (minimum) in both directions of the jib extension. This is to minimize the risk of damage to the hook suspension when placing crane equip-ment in the truck body.

Max. 26,5

Min

. 52

Max. R35

Max. 70

35°

Recommended dimensions for connecting link.

Page 39: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 35 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Technical Data, Winch

PERFORMANCE (AT 2176 PSI) UNIT 1.5T WINCH 2.5T WINCHMax. wire pull – 1st layer lbs 3307 5512Max. wire pull – 2nd layer lbs 3020 5071Max. wire pull – 3rd layer lbs 2778 4630Max. wire pull – 4th layer lbs 2579 4299PERFORMANCE (150 BAR) UNIT 1.5T WINCH 2.5T WINCHMax. wire pull – 1st layer kg 1500 2500Max. wire pull – 2nd layer kg 1370 2300Max. wire pull – 3rd layer kg 1260 2100Max. wire pull – 4th layer kg 1170 1950

WIRE SPEED (AT 40 G/MIN) UNIT 1.5T WINCH 2.5T WINCHMax. wire pull – 1st layer g/min 5.8 6.3Max. wire pull – 2nd layer g/min 6.3 6.9Max. wire pull – 3rd layer g/min 6.9 7.4Max. wire pull – 4th layer g/min 7.4 7.9WIRE SPEED (AT 40 L/MIN) UNIT 1.5T WINCH 2.5T WINCHMax. wire pull – 1st layer m/min 22 24Max. wire pull – 2nd layer m/min 24 26Max. wire pull – 3rd layer m/min 26 28Max. wire pull – 4th layer m/min 28 30

WEIGHTS UNIT 1.5T WINCH 2.5T WINCHTare weight, winch (CE) lbs 143 198Fixed parts (valve section, brackets,hoses etc.) lbs 110 110Wire Ø10 x 50 m lbs 66 66Spare parts, single snatch block lbs 66 66Spare parts, double snatch block lbs 88 88WEIGHTS UNIT 1.5T WINCH 2.5T WINCHTare weight, winch (CE) kg 65 90Fixed parts (valve section, brackets, hoses etc.) kg 50 50Wire Ø10 x 50 m kg 30 30Spare parts, single snatch block kg 30 30Spare parts, double snatch block kg 40 40

Page 40: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 36 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Winch

2,5T: 3’0”1,5T: 3’1”

2,5T: 9251,5T: 945

1010

Page 41: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 37 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension sketch, Stand-Up Platform (STD & Valve Control)

1’10

”55

5

5’11

1820

2’9”850

TOP CHASSIS

Stand-Uo Platform (STD)

1515

5’0”

11”

275

2’10”875

TOP CHASSIS

Stand-Up Platform (Valve Control)

Page 42: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 3 38 1430 MCS, Dimension Drawings

1430 MCS - Manual # 99906329

1430 MCS - Dimension Sketch, Internal Hose Routing

B

8’3”

250

2 A

D

øD A B

K1, K2, K3

K4

K5

K6

øD A B

K1, K2, K3 480 230mm 78mm

K4 520 250mm 58mm

K5 570 275mm 33mm

K6 620 300mm 8mm

Feet / Inches Metric

480

520

570

620

9.1” 3.1”

9.8” 2.3”10.8” 1.3”

11.8” 0.3”

Page 43: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 39 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

Section - 41430 MCS, Hydraulic Drawings

Page 44: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 40 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Pressure Setting Diagram, Manual

Working Pressure on Main-Relief Valve & Port- Relief Valves

Function Direction Port HDL(BAR)

HDL [PSI]

Main-relief valve 330 4786

Slewing systemRight A P PLeft B P P

Boom cylinderDown A 100 1450Up B 340 4931

Jib cylinderUp A 340 4931Down B 200 2901

Extension cylindersExtend A P PRetract B P P

RotatorRight A 200 2901Left B 200 2901

GrabOpen A 200 2901Close B 200 2901

Separate stabilizer valve All 150 2176

Working Pressure on Load-holding Valves

Function Direction Port Opening Pressure [BAR]

Opening pressure [PSI]

Boom cylinder 350 5076Jib cylinder 350 5076Slewing system 185 2683

Extension cylindersRetract A 210 3046Extend B 430 6237

Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 320 [BAR] 4641 [PSI]HDL 290 [BAR] 4206 [PSI]

Max. pump performancePump performance, 1 Circuit 45 L/min 11.9 g/pm

Page 45: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 41 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Pressure Setting Diagram, Fixed Flow Pump & Danfoss (Man)

Working Pressure on Main-Relief Valve & Port- Relief Valves

Function Direction Port Port Relief(BAR)

LS Pressure [BAR]

Port Relief[PSI]

LS Pressure [PSI]

Main-relief valve 300 4351

Slewing systemRight A P 180 P 2611Left B P 180 P 2611

Boom cylinderDown A 125 100 1813 1450Up B 320 350 4641 5076

Jib cylinderUp A 350 350 5076 5076Down B 250 230 3626 3336

Extension cylindersExtend A P 280 P 4061Retract B P 280 P 4061

RotatorRight A P 50-300 P 725-4351Left B P 50-300 P 725-4351

GrabOpen A P 50-300 P 725-4351Close B P 50-300 P 725-4351

Separate stabilizer valve All 150 2176

Working Pressure on Load-holding Valves

Function Direction Opening Pressure [BAR]

Opening pressure [PSI]

Slewing systemRight 185 2683Left 185 2683

Boom cylinderUp 325 4714Down - -

Jib cylinderUp 350 5076Down 300 4351

Extension cylindersRetract 430 6237Extend 210 3046

Pressure setting for Load Moment Limitation (LMB)Load moment limitation (LMB) 285 [bar] 4134 [PSI]

Max. pump performanceChoice of pump 1 x Fixed 1 x FixedPump performance 70 L/min 18.5 g/pm

Page 46: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 42 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Danfoss, Single-Circuit Fixed 6 FCTS. RC (2 EXV: Grab + Rotator)

Option

Recommended

B1M3B

A

M2

M1

A1

55227

C2 C1

V2 V1

5904

4

PVP

T

P

LS M

5526

1 / 5

5262

A1 B1

A B

5902

7

MM2M1 C1C2

V1V2

X4

X1

X2

X3

A-PORTA6

B6

A-PORTA5

B5

A-PORTA4

B4

A3

B3A-PORT

A-PORTA2

B2

A-PORTA1

B1

63092/63301/63303/63313

P PVSKPst

Tst

58478

58478

58478

58478

58478

58478

58478

58478

58478

58479

4940

1

Obsolete for 1430-K

Page 47: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 43 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Danfoss, single-circuit variable6 fcts. RC/HS dir. valve contr. (2 EXV: Grab + Rotator)

B1M3B

A

M2

M1

A1

55227

C2 C1

V2 V159

044

55261 / 55262

A1 B1

A B

5902

7

MM2M1 C1C2

V1V2

X4

X1

X2

X3

59823

A-PORTA6

B6

A-PORTA4

B4

A-PORTA3

B3

58479

63393

A-PORTA1

B1

63394

T

58479

PVP

P

59823

LS M

58478

A-PORTA5

B5

A-PORTA2

B2

PVSK

HPCO

P

PVPT

P

LS

PVSI

LX

Pst

Option

Recommended

494015847

8

6340844

Tst

58478

58478

A1

B1

5051

750

517

Option

Page 48: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 44 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Hydrocontrol, single-circuit fixed 6 fcts. Std./HS, std./HS dir. valve contr. HDL (2 EXV: Grab + Rotator)

Option

A-PORT

A-PORT

A-PORT

A-PORT

C2 C1

V2 V1

5904

4

Q-MODULT

P

5526

1 / 5

5262

A1 B1

A B

A-PORT

A-PORT

5902

7

MM2M1 C1C2

V1V2

X4

X1

X2

X3

PstHPCO

M

A5

B5

A2

B2

A3

B3

A4

B4

A1

B1

A6

B6

58478

58478

58478

58478

58478

58478

58478

58478

58478

58479

NEM

-MO

DU

L

TP

55265 / 55266 / 55267

Tst

B1M3B

A

M2

M1

A1

55227

Max 3 bar

Page 49: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 45 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Hydrocontrol, single-circuit fixed 6 fcts. RC med HDL (2 EXV: Grab + Rotator)

Pst HPCO

B1M3B

A

M2

M1

A1

55227

C2 C1

V2 V1

5904

4

5526

1 / 5

5262

A1 B1

A B

5902

7

MM2M1 C1C2

V1V2

X4

X1

X2

X3

A1

B1

58478

58478

58478

58478

58478

58478

58478

58478

58478

58479

Tst

A-PORTA5

B5

M

55290

A-PORTA1

B1

A-PORTA4

B4

A-PORTA2

B2

A3

B3A-PORT

A-PORTA6

B6

Option

Q-MODULP2

M

TQ-MODUL

T

P1

Page 50: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 46 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Hydraulic Diagram - Stablilizer circuit – 2 fcts.

PstTst

A-PORT

A2 B2

A-PORT

A1 B1

5522

5

PT

5849

6

5849

6

Page 51: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 47 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts.

PstTst

D

C

5522

8

5849

6

5849

6

D

C55

228

A14 B14 A13 B13 A12 B12 A11 B11

5522

6 / 5

5281

PT

A-PORT A-PORT A-PORTA-PORT

Page 52: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 48 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. RC

D

C

5522

8

5849

6

5849

6

D

C

5522

8

PstTst

A13 B13 A12 B12

5527

6

T

B-PORT

A-PORT

A11 B11

PA-PORT

B-PORT

NEM-MODULT P

T

ø1 mmø1 mm

50521

C1

C2

C3

D1

D2

D3

D4

C4

49187

49187

Only when HR stabilizer

Page 53: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 49 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts.

D

C55

228

5849

6

5849

6

D

C

5522

8

Separate traverse

PstTst

A15 B15 A14 B14 A13 B13 A12 B12

5527

7

TA-PORT

B-PORT

A-PORTA-PORT

A11 B11

PA-PORT

OPT.

B-PORTB-PORTB-PORT

OPT.OPT.OPT.

ø1 mm ø1 mm

50521

C1

C2

C3

D1

D2

D3

D4

C4

Page 54: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 50 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Hydraulic Diagram - Stablilizer circuit – 4 fcts. + 4 available fcts. RC

D

C

5522

8

5849

6

5849

6

D

C

5522

8

Separate traverse

PstTst

P

P

A15 B15 A14 B14 A13 B13 A12 B12

5527

5

TA-PORT

B-PORT

A-PORTA-PORT

A11 B11

A-PORT

OPT.

B-PORTB-PORTB-PORT

OPT.OPT.OPT.

NEM-MODULT

T

ø1 mm ø1 mm

50521

C1

C2

C3

D1

D2

D3

D4

C4

Only when HR stabilizer

49187

49187

Page 55: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 51 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Lubrication instructions

The present instructions are valid for the following loader cranes:

For the K-Series Cranes Catalogue

1300-K / 1420-K / 1520-K 38 084 1310-K / 1430-K / 1530-K 38 085 1500-K / 1720-K / 1820-K 38 086 1510-K / 1730-K / 1830-K 38 087 1800-K / 2020-K / 2120-K 38 088 1810-K / 2030-K / 2130-K 38 089 2200-K / 2420-K / 2620-K 38 090 2210-K / 2430-K / 2630-K 38 091

For the T-Series

Cranes Catalogue1410-T / 1530-T / 1630-T 38 100 1910-T / 2030-T / 2130-T 38 101

The crane models concerned by these instructions are to a great extent equipped with maintenance-free composite bearings. However, for a limited number of bearings, regular lubrication has to be carried out according to these instructions.

The crane has to be greased in the following places:

1. Central greasing on the base.2. The push rods at the boom and jib cylinders .3. Sliding surfaces in the boom system.

Please see the Instruction Manual, Cranes, for recommended oil and grease.

Re 1) Central lubrication on the base: The base is equipped with a central greasing point where all lubrication of moving parts in the slewing system is carried out.

The central greasing point is placed on the cross beam of the base and is indicated in the figure below.

Page 56: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 52 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Lubrication instructionsLubrication instructions

Figure 1 - Central greasing point on the base

Greasing has to be carried out at the greasing points indicated above, while the crane is swung from stop to stop. Repeat the lubrication of the cogging twice. The crane has to be lubricated again after 50 hours of operation or as a minimum every month. Furthermore the crane has to be lubricated right before a longer period of standstill.

Below is indicated where the central greasing points are connected on the central part of the base.

Figure 2 – Connection points on the central part of the base.

Top bearing

Guide for rack

Top bearing

CoggingBottombearing

Cogging

Top bearing (2 places)

Guide for rack

Bottombearing

Page 57: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 53 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

Lubrication instructions

Re 2) For the K-Series:

The push rods at the boom and jib cylinders: Lubricate the crane’s push rods at the boom cylinder at the points indicated below. They have to be greased after 250 hours of operation or every third month as a minimum.

Figure 3 - Greasing points on inner push rods at the boom cylinder

Note:The 1310K, 1430K, 1530K, 1510K, 1730K, 1830K, 1810K, 2030K, 2130, 2210K, 2430K, 2630KSeries only have a push rod at the jib cylinder.

Lubricate the crane’s outer push rod at the jib cylinder at the points indicated below. They have to be greased after 250 hours of operation or every third month as a minimum.

Figure 4 – Greasing points on outer push rod at the jib cylinder

Greasing points on the push rod

Greasing points on the outer push rod

Page 58: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 54 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

Lubrication instructions

Re 3) For the T-Series:

Pins on the main boom: Lubricate the pins of the crane on the main boom at the points indicated below. They have to be greased after 250 hours of operation or every third month as a minimum.

Greasing points on the push rod

Lubrication instructions

Re 4) Sliding surfaces in the boom system:

Grease the boom system on all surfaces where the bearing slide blocks are running. I.e. grease the extensions externally on the underside and internally on the upper side.

Figure 5 - Boom system with indication of greasing points

The boom system has to be greased after 100 hours of operation or every month as a minimum. Furthermore the boom system has to be lubricated right before a longer period of standstill.

Grease the external underside

Grease the internal upper side.

Page 59: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 55 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Change of slewing area

Change of slewing area

The present instructions are valid for the following loader cranes:

For the K-Series Cranes Catalogue

1300-K / 1420-K / 1520-K 38 084 1310-K / 1430-K / 1530-K 38 085 1500-K / 1720-K / 1820-K 38 086 1510-K / 1730-K / 1830-K 38 087 1800-K / 2020-K / 2120-K 38 088 1810-K / 2030-K / 2130-K 38 089 2200-K / 2420-K / 2620-K 38 090 2210-K / 2430-K / 2630-K 38 091

For the T-Series

Cranes Catalogue1410-T / 1530-T / 1630-T 38 100 1910-T / 2030-T / 2130-T 38 101

These instructions describe how to change the slewing area of a ready-mounted crane.

It is important to mention that change of slewing area should be avoided by a necessary drawing up of the installation in connection with making the quotation and placing of the order. Otherwise expenses for changing the slewing area must be considered a direct economic loss for the seller (vendor).

Procedure:1. Take off the lubricating brush and the slewing sensor ( - if the crane is equipped with a

such). The components are fitted on the side of the central part of the base. Eachcomponent is fitted with two (2) x M6 screws.

Page 60: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 56 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

Change of slewing area

2. All hoses coming out of the column are removed from the control valve.

Figure 1 – Cover for lubricating brush on the side of the central part of the base.

Figure 2 – Hose connection for control valve

Page 61: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 57 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

Change of slewing area

3. Take off the protection plate. The plate is fitted with two (2) x M8 bolts with nuts.

4. Remove the hose clamp fixing the hoses at the protection plate.Please note:If there is no marking of the function of each individual hose, this has to be added beforedisassembling. It should also be marked where the hose clamp fixes the hoses. Thisshould be done to be able to recreate the correct length of each hose from the hose clampto the control valve.

Figure 3 – The underside of the crane with protection plate fitted.

Figure 4 – Hose routing through the underside of the column.

Page 62: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 58 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

5. Loosen the hose connection and pull it downwards until the circlip on the bottom of thecolumn is visible and can be reached. The hose connection is fitted by means of four (4) xM8 button head screws. Take off the circlip on the bottom of the column.

6. It is now possible to lift up the column and place it again in the new slewing area required.Please note:Make sure that the column is free of the top and bottom bearings, when it has been raisedapprox. 75 mm. We recommend that lifting of the column with boom system is carried outas a two-point lift so that the burden is kept stable when it is no longer supported by thetop and bottom bearings. Otherwise bearings, coggings and hose connections may bedamaged.

Depending on the crane model, we recommend the following lift of the column inconnection with change of slewing area:

The K-Series:The 1300-K – 1830-K Series: 140 mm The 1800-K – 2630-K Series: 150 mm

The T-Series: The 1410-T - 1630-T Series: 140 mm The 1910-T - 2130-T Series: 150 mm

In the picture below, you see a cross-section through the lower part of a column and the central part of a base. You see the column lifted up to the area where the slewing area can be changed. Please note the dirt-repelling recess above the lower column bearing. If

Figure 5 – The underside of the crane with protection plate and hose connection removed.

Page 63: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 59 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

the column is lifted too high, it will hit against the rack, if the column is not tilted away from the rack.

--- ooo ---

Assembling takes place in the opposite order as the items above. Make sure that the hose connections coming out of the column are positioned without the hoses being mutually twisted. This is how to ensure the longest possible life span of the hose routing inside the column.

Before tightening the hose clamp on the protection plate for fixing of hoses, each hose has to be positioned with correct length from the hose clamp to the control valve. This is to ensure that there is enough free hose length inside the column. (- this is used for instance in case of replacement of hoses.). In this connection it may be easiest to carry out the adjustment of the length of the hose by temporarily loosening and lifting the complete kit of hoses through the protection plate at the top of the column. Please see Service Information for replacement of hoses inside the column.

--- ooo ---

Figure 6 – Picture of the cross-section of the central part of a base with the column lifted.

Page 64: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 60 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - Replacement of hydraulic hoses in column

Replacement of hydraulic hoses in column

The present instructions are valid for the following loader cranes:

For the K-Series Cranes Catalogue

1300-K / 1420-K / 1520-K 38 084 1310-K / 1430-K / 1530-K 38 085 1500-K / 1720-K / 1820-K 38 086 1510-K / 1730-K / 1830-K 38 087 1800-K / 2020-K / 2120-K 38 088 1810-K / 2030-K / 2130-K 38 089 2200-K / 2420-K / 2620-K 38 090 2210-K / 2430-K / 2630-K 38 091

For the T-Series

Cranes Catalogue1410-T / 1530-T / 1630-T 38 100 1910-T / 2030-T / 2130-T 38 101

These instructions describe how to change hydraulic hoses in the column.

Replacement of hoses with internal hose routing inside the column is more demanding than for crane models with hose routing on the outside of the column. However, a longer life span for the internal hose routing and a more functional crane design compensates for this.

In case of urgent repair of hose rupture, carry out emergency repair as described in the Service Information no. 38 0XX 230 – “By-pass hose routing for emergency repair”.

If you have problems locating which one of the hoses that have been damaged it may be necessary to carry out a separate pressure test for each individual hose.

Procedure:

1. Dismount the hose shield at the top of the column.

Page 65: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 61 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

2. Lift up the bundle of hoses either by means of a workshop crane or by means of the HMFservice tools P/N 82 00 030 (please see spare parts catalogue). When using the servicetools, fit the threaded pins into the hole plate for the bundle of hoses at the top of thecolumn. Then fit the service tools onto the flange at the top of the column. Thereuponconnect the threaded pins to the lifting tools. Dismount the screws at the back of thecolumn holding the hole plate. Then lift the bundle of hoses using the service tools. Nowthere is access to the hole plate with swivel coupling and hose ends.

Figure 1 – Photo of the upper part of the column with hose shield

Page 66: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 62 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

3. Take off the end of the damaged hose from the swivel coupling on the hole plate. Screwthe end of the damaged hose together with the end of the new hose. (In case of limitedspace under the crane, it may be necessary to pull the new hose through using a string orthe like instead of direct connection to the damaged hose. This is because the rigid partnext to the connection cannot be turned out into the open at the bottom of the column).

Figure 2 – Photo of the top of the column with the bundle of hoses lifted using the service tools.

Page 67: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 63 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

4. Dismount the protection plate underneath the base.

5. Take off the end of the damaged hose from the control valve.6. Loosen the clamp fixing the hoses at the protection plate to the point where the upper

hose end can come through.7. Pull out the damaged hose (- with the new one connected to the upper end) down through

the column. Pull the hose from below.8. Connect the hose ends to the swivel coupling on the hole plate as well as to the control

valve.9. Tighten the hose clamp and mount the protection plate.10. Lower the hole plate into the column and mount it again. Dismount the service tools.11. Mount the hose shield onto the column again.

In case of hose rupture you have to consider whether you should pull up the entire hose kit and change all hoses fed inside the column instead. One or several of the other hoses may also be worn and need replacement.

--- ooo ---

Change hoses led out of the front plate of the column for connection to the boom cylinder in the following way:

1. Dismount the hose connection on the load-holding valve on the boom cylinder.2. Take off the nuts on the front plate behind the boom cylinder. (It may appear easier to

dismount the lower pin in the boom cylinder and turn it away. The crane must be properlysupported before dismounting the pin).

3. Dismount both hose connections for the boom cylinder on the control valve.4. Tie the two lowest hose ends together with a string. This string must have a free end of at

least 2 metres.5. Pull out the hose kit from the top of the column.

Change the damaged hose, and both of them if necessary. To remount the hose/s, reverse the procedure.

--- ooo ---

Figure 3 – Photos of the protection underneath the base with and without protection plate.

Page 68: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 64 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

1430 MCS - By-pass hose routing for emergency repair

The present information is valid for the following cranes:

For the K-Series

Cranes Catalogue1300-K / 1420-K / 1520-K 38 084 1310-K / 1430-K / 1530-K 38 085 1500-K / 1720-K / 1820-K 38 086 1510-K / 1730-K / 1830-K 38 087 1800-K / 2020-K / 2120-K 38 088 1810-K / 2030-K / 2130-K 38 089 2200-K / 2420-K / 2620-K 38 090 2210-K / 2430-K / 2630-K 38 091

For the T-Series

Cranes Catalogue1410-T / 1530-T / 1630-T 38 100 1910-T / 2030-T / 2130-T 38 101

This information describes establishing of an emergency hose connection for the crane functions in case of hose rupture on the part of the crane’s hose routing that is fed inside the column.

The emergency hose connection can be used until you reach a service point.

The following hoses can be used for emergency purpose:

All permanent hose equipment, which is fitted on the crane, appears from the spare parts catalogue of the crane in question.

Hose connection from – to: Hose no.: Control valve – Boom “up/down” 00 15 250 Control valve – Jib ”extend/retract” 00 17 610 Control valve – Extension ”extend” (hole plate on jib) 56 524 Control valve – Extension ”retract” (hole plate on jib) 00 17 550 Control valve – Extra valves (hole plate on jib) 00 17 550 Control valve – Winch (hole plate on jib) 56 524

Page 69: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 65 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

By-pass hose routing for emergency repair

In the following it is indicated in the photos how the different emergency hoses are fitted.

Figure 1 – Illustration of fitting of the hose loop from the control valve and further onto the crane. Please note the first fixing of the upper end of the hose loop on the boom cylinder as well as hydraulic connection down to the boom cylinder.

Figure 2 – Illustration of the hose routing further up to the connection on the jib cylinder.

Page 70: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 66 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

Cut off the part of the damaged hose placed below the main boom. Cut it as far to the back below the boom as you can reach, and take off the part of the hose which is fitted on the hole plate on the jib. Remove the piece of hose.

Instead of mounting by means of cable ties, it may be advantageous to fit the emergency hose under the hose clamps below the boom.

--- ooo ---

Figure 3 – Illustration of the hose routing further out under the main boom.

Page 71: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 67 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

Handling equipment Lifting yoke for handling of loader

The present instructions are valid for the following loaders:

Loaders Catalogue1300-K / 1420-K / 1520-K 38 084 1310-K / 1430-K / 1530-K 38 085 1500-K / 1720-K / 1820-K 38 086 1510-K / 1730-K / 1830-K 38 087 1800-K / 2020-K / 2120-K 38 088 1810-K / 2030-K / 2130-K 38 089 2200-K / 2420-K / 2620-K 38 090 2210-K / 2430-K / 2630-K 38 091

This information serves as instruction for safe internal handling of the loader in case of lifting when moving and mounting it on a truck, etc.

The figure 1 below shows a complete lifting yoke (82 00 010).

Spare parts numbers of the lifting yoke parts appear from the spare parts catalogue of the loader in question.

Figure 1 – Complete lifting yoke

Page 72: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 68 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

The figure below shows the positioning of the lifting yoke in connection with lifting.

Figure 2 – Loader with lifting yoke seen from the side

Figure 3 – Loader with lifting yoke seen from the rear.

Page 73: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

Section - 4 69 1430 MCS, Hydraulic Drawings

1430 MCS - Manual # 99906329

Lifting Instructions:

The max. permissible lifting capacity of the lifting yoke is 4.0 t.

The following instructions have to be followed when using the lifting yoke:

• The loader must be locked in stowing position while handling it by means of thelifting yoke. (Locking can take place by fitting of a pin in the stowing bracket or bysecuring of the main boom to the base).

• The lifting yoke is equipped with a row of holes used for attachment over thecentre of gravity of the loader. (cf. figure 3).

• Never lift the loader with a Fly-Jib fitted in the boom system.• When lifting, always keep at least a 5 metres safety distance from the loader.

The positioning of the centre of gravity of the loader depends on the loader configuration as regards the number of extensions and the equipment, etc. Therefore, the loader may, in certain loader configurations, not be completely in vertical position during lifting. In this connection, please pay attention to the fact that the loader may skid on the surface when it is lifted.

Page 74: 1430 MCS Technical Specifications · 2020. 10. 27. · Section - 1 5 1430 MCS, Technical Specifications 1430 MCS - Manual # 99906329 1430 - Specifications, Metric Performance Unit

IMT reserves the right to make changes in engineering, design, specifications, add improvements or discontinue manufacturing at any time without notice or obligation.

IMT and IMT LOGO are registered trademarks of Iowa Mold Tooling Co., Inc., Garner, IA, USA.© 2021 Iowa Mold Tooling Co., Inc. All Right Reserved.

IOWA MOLD TOOLING CO., INC.

P.O. Box 189 Garner, IA 50438Tel: 641.923.3711

Fax: 641.923.2424www.imt.com