14328l-007

© 2011 ZIH Corp. All product names and numbers are Zebra trademarks, and Zebra and the Zebra logo are registered trademarks of ZIH Corp. All rights reserved.

14328L-00708/31/2011

E53.17.x, E53.15.x, and E50.13.x Summary of Firmware Changes

This document summarizes the following E50.13.x and E53.15.x firmware releases:

E53.17.11

Release Date: 9 September 2011

This firmware release is for use on:

• All S4M™ (203 dpi) printers

• All ZM400™ /ZM600™ (203 dpi) printers

This firmware includes all features of previous E53.17.x releases.

Changes

• Wired PS Check has been removed from the menu.

• The ZebraNet b/g Print Server is now supported for the S4M, ZM400/ZM600 printers.

• The ZebraNet Internal Wireless Plus Print Server option board firmware has been updated to version 2.12.1761.

Issues Corrected

• Adjustments to the LEFT POSITION setting on the front panel will now be applied to the next label sent to the print engine.

• The S4M and ZM400/ZM600 will no longer pause after extended usage.

Firmware Release Number Release Date See Page

E53.17.11 9 September 2011 page 1



E53.15.0B 18 March 2009 page 3

E53.15.0A 21 November 2007 page 4

E53.15.0 13 August 2007 page 6

E50.13.5 14 July 2006 page 7

E50.13.3 9 November 2005 page 8

E50.13.2 27 October 2005 page 8

Summary of Firmware ChangesE53.17.3

2

14328L-007 08/31/2011

E53.17.3






Changes

• None

Issues Corrected

• The printer shall now retain the Q value after a power cycle.

• A "0" will no longer be added to a Code 128 the barcode when the data stream is "<T>".

• The print position on S4M™ and 2746e™ shall now be the same when using black marked media.

E53.17.2






Changes

• Media power up now defaults to no motion

• On the ZM400/ZM600 printers the printserver web pages are now available when the internal printserver is used.

• On the ZM400/ZM600 printers FTP is now available when the internal printserver is used.

• On the ZM400/ZM600 printers SNMP is now available when the internal printserver is used.

• On the ZM400/ZM600 printers SMTP is now available when the internal printserver is used.

• The ZPL Code Validation feature is turned on by default, for more information on this feature see the documentation in the ZPL manual on the ^CV command.

• Added device.printhead.coldwarning command to control the Head Cold warning. Default is OFF.

3Summary of Firmware ChangesE53.15.0B

08/31/2011 14328L-007

Issues Corrected

• The OS command will now correctly reverse the transmissive (gap) sensor's normal operation.

• Changes to the Tear Off setting on the front panel will now be saved and used in printing.

• Serial handshaking performance improved at higher baud rates.

• Formats using a PDF417 barcode will encode a backslash (\) correctly .

• A barcode will no longer print if no data is provided for the barcode.

• RS-232 handshaking has been corrected.

• Barcodes will no longer truncate at the right edge of the label.

• Tear Off value no longer reverts to zero when exiting the menu.

• Labels print in correct order when using counter values in the format.

• Code 128 Auto barcodes will now print when the data contains an F1.

• Maxicode will now allow a nine digit zip to have a comma as a separator between the first five digits and the last four.

• A Maxicode barcode format will print when a zip code begins with a zero.

• The f command will now take priority over the front panel Tear Off setting.

• Formats containing a single double quote will now print correctly.

• Memory management enhanced to reduce need to run defragmentation routine.

• Stored templates will now consistently print.

E53.15.0B

Release Date: 18 March 2009





Issues Corrected and Items Changed

• Front panel buttons are responsive with offset greater than +30.

Summary of Firmware ChangesE53.15.0A

4

14328L-007 08/31/2011

E53.15.0A

Release Date: 21 November 2007





Changes

Support added for:

• The Wireless Plus Print Server on the S4M, ZM400, and ZM600 EPL models, with the ability to use the following wireless securities - dependent on the PCMCIA based RF card used (see the ZebraNet Wireless User Guide for full details and configuration commands):

• OPEN

• LEAP

• EAP-FAST

• EAP-TLS

• EAP-TTLS

• WPA EAP-FAST

• WPA EAP-TLS

• WPA EAP-TTLS

• WPA2 LEAP

• WPA2 PEAP

• WPA2 EAP-FAST

• WPA2 EAP-TLS

• WPA2 EAP-TTLS

• Additional Set/Get/Do commands to configure and get status on the printer and print server*.

* See the latest EPL manual (available at www.zebra.com) for complete details on new commands.

http://www.zebra.com/support

5Summary of Firmware ChangesE53.15.0A

08/31/2011 14328L-007

Wireless Notes

The following items are issues Zebra has noted during testing with various wireless networking products.

• Conflicts can exist between the Symbol LA-4137CF and some Cisco Access Points. This is characterized by the RF card reaching the Maximum Retry timeout.

• Conflicts can exist between the 802.11B Symbol LA-4137CF and 802.11G support on some Access Points. One potential work-around is to disable G support on the Access Point.

• It is recommended to set WPA Handshaking to 1000.

• It is recommended to disable the Aironet Extensions.

• It is recommended to use Cisco Access Point firmware 12.3(8)JAE1 or later.

Table 1 • Wireless Plus PrintServer Security Support

Securities Supported

Cisco Symbol

Cisco CB21 (CardBus)

Cisco 350 (PCMCIA)

LA-4121 (PCMCIA)

LA-4137CF (Compact Flash)

Open Yes Yes Yes Yes

KERBEROS Not Supported Not Supported Yes Yes

WEP 40-bit & 128-bit Yes Yes Yes Yes

LEAP Yes Yes Yes Yes

PEAP Yes Not Supported Yes Yes

EAP- FAST Yes Not Supported Yes Yes

EAP-TLS Yes Not Supported Yes Yes

EAP-TTLS Yes Not Supported Yes Yes

WPA PSK Yes Yes Yes Yes

WPA LEAP Yes Yes Yes Yes

WPA PEAP Yes Yes Yes Yes

WPA EAP- FAST Yes Yes Yes Yes

WPA EAP-TLS Yes Yes Not Supported Yes

WPA EAP-TTLS Yes Yes Not Supported Yes

WPA2 PSK Yes Not Supported Not Supported Not Supported

WPA2 LEAP Yes Not Supported Not Supported Not Supported

WPA2 PEAP Yes Not Supported Not Supported Not Supported

WPA2 EAP- FAST Yes Not Supported Not Supported Not Supported

WPA2 EAP-TLS Yes Not Supported Not Supported Not Supported

WPA2 EAP-TTLS Yes Not Supported Not Supported Not Supported


6

14328L-007 08/31/2011


• The Code 93 Barcode now prints correctly with full ASCII data strings.

• Adjusting the Left Position setting on the front panel now adjusts the position of the printed image.

E53.15.0

Release Date: 13 August 2007




E50 has been changed to E53. This firmware includes all features of previous E50.13.x releases.

Changes

Support added for:

• The graphic display on the ZM400/ZM600 printers (ability to display Japanese, Simplified & Traditional Chinese, Korean)

• The Internal Wired Print Server on the ZM400 and ZM600 models

• The Wireless Plus Print Server on the S4M, ZM400, and ZM600 models, with the ability to use the following wireless securities - dependent on the PCMCIA based RF card used (see the Wireless Plus manual for full details and configuration commands):

• WEP 40 BIT

• WEP 128 BIT

• PEAP

• WPA PSK

• WPA2 PSK (no key rotation)

• WPA PEAP

• WPA LEAP

• Kerberos

• The User Selectable “Primary Print Server” which allows the user to configure the printer determines which print server type - wired or wireless - to use as the Active Print Server at power up. Available on the ZM400/ZM600 and for use with the wired and wireless print servers. Controlled via the Front Panel and Set/Get/Do commands*.

• A Network configuration label on ZM400 and ZM600 that can display details on the External Wired, Internal Wired or Wireless print servers

• The ability to display the “Active Print Server” on the front panel and network configuration label

7Summary of Firmware ChangesE50.13.5

08/31/2011 14328L-007

• The OC command is interpreted on a format by format basis. In some cases, if later formats contain a different value for the p1 (cut quantity) parameter than earlier formats, the printer may use the value from an earlier format.

• When using counters in QR Code fields, the printer may use data from an earlier counter value in a later printed code

• Additional Set/Get/Do commands to configure and get status on the printer and print servers*

* See the latest EPL manual (available at www.zebra.com) for complete details on new commands.


• The S4M now responds to the receipt of Q command in the same way as the 2736e

• The S4M now responds to KDU serial number prompts

• The FR command now functions in the same way it does on a 2746e

• Printing a batch of labels with time stamps now functions in the same way as it does on a 2746e

• Printers using E53.15.x firmware will process labels with both R and q commands in the same format in the same was as a 2746e does

• Maxicode will appear on label when postal code is less than 9 digits.

• Autofr now functions on S4M, ZM400, and ZM600 printers in the same as it did on the 2746e

• The internal print server on the ZM400/ZM600 and the wireless print server on E53.15.x-based printers does not support FTP, UDP, SNMP, IPP (port 631) or Web (port 80)

E50.13.5

Release Date: 14 July 2006

This firmware release is for all S4M™ (203 dpi) printers. It includes features of previous V50.13.x releases.


• The S4M now reports back to the host when the US command is used.

http://www.zebra.com/support


8

14328L-007 08/31/2011

E50.13.3

Release Date: 9 November 2005

This firmware release is for all S4M™ (203 dpi) printers. It includes features of previous V50.13.x releases.


• Improvements to print head detection (203 dpi)

E50.13.2

Release Date: 27 October 2005

This is the initial release of this firmware. It is for use on all S4M™ (203 dpi) printers.

14328l-007

Documents