1705-03 simi valley high school mpr specifications ... · 1705-03 simi valley high school mpr...

1705-03 Simi Valley High School MPRArchitecture for Education

1705-03 Simi Valley High SchoolMPR

10/18/2019 TABLE OF CONTENTS00 0110-2

Certification of Non-Asbestos, Non-LeadConstruction Forms, Waivers, and Releases, Owners Assessment Summary

SPECIFICATIONSDIVISION 01 -- GENERAL REQUIREMENTS

01 2300 - Alternates01 3000 - Administrative Requirements01 4000 - Quality Requirements01 4200 - Testing and Inspection01 5000 - Temporary Facilities and Controls01 6000 - Product Requirements01 7000 - Execution and Closeout Requirements01 7800 - Closeout Submittals

DIVISION 02 -- EXISTING CONDITIONS 02 4100 - Demolition

DIVISION 03 -- CONCRETE 03 0516 - Underslab Vapor Barrier03 1000 - Concrete Forming and Accessories031100 - Geofoam Lightweight Fill03 2000 - Concrete Reinforcing03 3000 - Cast-in-Place Concrete

DIVISION 04 -- MASONRY 04 2000 - Concrete Unit Masonry

DIVISION 05 -- METALS 05 1200 - Structural Steel05 1600 - Metal Framing Systems (Sure-Board)05 3100 - Steel Decking05 4100 - Load Bearing Metal Studs05 5000 - Metal Fabrications05 5100 - Metal Stairs05 5150 - Ladders05 5213 - Steel Railings05 7000 - Decorative Formed Metal Guardrails

DIVISION 06 -- WOOD, PLASTICS, AND COMPOSITES 06 1000 - Rough Carpentry06 2000 - Finish Carpentry06 4100 - Architectural Wood Casework

DIVISION 07 -- THERMAL AND MOISTURE PROTECTION 07 0150.19 - Preparation for Re-Roofing07 2100 - Thermal Insulation07 2500 - Weather Barriers



10/17/2019 TABLE OF CONTENTS

00 0110-3

07 2505 - Gypsum Board Weather-Resistant Barrier and Air Barrier System

07 2726 - Fluid-Applied Weather Barriers

07 5400 - Thermoplastic Membrane Roofing

07 6200 - Sheet Metal Flashing and Trim

07 7100 - Roof Specialties

07 7200 - Roof Accessories

07 8700 - Smoke Containment Barriers

07 9005 - Joint Sealers

07 9513 - Expansion Joint Cover Assemblies

DIVISION 08 -- OPENINGS

08 1113 - Hollow Metal Doors and Frames

08 1425 - Clad Wood Doors

08 3100 - Access Doors and Panels

08 3313 - Coiling Counter Doors

08 3513 - Accordion Folding Doors

08 4313 - Aluminum-Framed Storefront & Window Systems

08 4413 - Glazed Aluminum Curtain Walls

08 7100 - Door Hardware

08 8000 - Glazing

DIVISION 09 -- FINISHES

09 0600 - Schedule for Finishes

09 2116 - Gypsum Board Assemblies

09 2236.23 - Metal Lath and Accessories

09 2405 - Portland Cement Plaster

09 3000 - Tiling

09 5100 - Acoustical Ceilings

09 6460 - Wood Stage Flooring

09 6500 - Resilient Flooring

09 6813 - Tile Carpeting

09 7200 - Wall Coverings

09 8433.11 - Sound-Absorbing Wall Panels

09 8436.14 - Sound Absorbing & Sound-Reflecting Ceiling Panels

09 9000 - Painting and Coating

09 9113 - Exterior Painting

09 9123 - Interior Painting

DIVISION 10 -- SPECIALTIES

10 1400 - Signage

10 2113.19 - Plastic Toilet Compartments

10 2800 - Toilet Accessories

10 4400 - Fire Protection Specialties




00 0110-4

DIVISION 11 -- EQUIPMENT

11 5213 - Projection Screens

11 6113 - Orchestra Enclosures

11 6133 - Theatrical Rigging

11 6143 - Theatrical Draperies

11 6151 - Theatrical Pipe Grid

11 6171 - Portable Dance Floor System

11 6191 - Theatrical Lighting Instruments and Accessories

DIVISION 12 -- FURNISHINGS

12 2400 - Roller Shade System

12 3600 - Countertops

12 6211 - Loose Audience Seating

12 6623 - Telescoping Seating Platforms

DIVISION 13 -- SPECIAL CONSTRUCTION (NOT USED)

DIVISION 14 -- CONVEYING EQUIPMENT

14 4216 - Vertical Wheelchair Lift

VOLUME TWO

DIVISION 21 -- FIRE SUPPRESSION

21 0500 - Common Work Results for Fire Suppression

21 1313 - Wet Pipe Sprinkler Systems

DIVISION 22 -- PLUMBING

22 0503 - Pipes and Tubes for Plumbing Piping and Equipment

22 0523 - General-Duty Valves for Plumbing Piping

22 0529 - Hangers and Supports for Plumbing Piping and Equipment

22 0553 - Identification for Plumbing Piping and Equipment

22 0700 - Plumbing Insulation

22 3400 - Domestic Water Heater Accessories

22 4000 - Plumbing Fixtures

DIVISION 23 -- HEATING, VENTILATING, AND AIR-CONDITIONING (HVAC)

23 0529 - Hangers and Supports for HVAC Piping and Equipment

23 0548 - Vibration and Seismic Controls for HVAC

23 0553 - Identification for HVAC Piping and Equipment

23 0593 - Testing, Adjusting, and Balancing for HVAC

23 0700 - HVAC Insulation

23 0800 - Commissioning of HVAC

23 1123 - Facility Natural-Gas Piping

23 2300 - Refrigerant Piping

23 3100 - HVAC Ducts and Casings

23 3300 - Air Duct Accessories




00 0110-5

23 3400 - HVAC Fans

23 3500 - Gravity Vents

23 3700 - Air Outlets and Inlets

23 8103 - Packaged Rooftop Air Conditioning Units - Small Capacity

23 8126 - Split-SystemAir Conditioners

23 8400 - Humidity Control Equipment

DIVISION 25 -- INTEGRATED AUTOMATION (NOT USED)

DIVISION 26 -- ELECTRICAL

26 0000 - Penetration Firestopping for Electrical

26 0500 - Common Work Results Electrical

26 0502 - Basic Electrical Requirements

26 0503 - Equipment Wiring Connections

26 0519 - Low-Voltage Electrical Power Conductors and Cables

26 0526 - Grounding and Bonding for Electrical Systems

26 0529 - Hangers and Supports for Electrical Systems

26 0533 - Raceway and Boxes for Electrical Systems

26 0534 - Floor Boxes for Electrical Systems

26 0535 - Raceways & Boxes for Audio-Visual Systems

26 0536 - Cable Trays for Electrical Systems

26 0548 - Seismic Controls for Electrical Work

26 0553 - Identification for Electrical Systems

26 0573 - Overcurrent Protective Device Coordination Study

26 0923 - Lighting Control Devices

26 0943 - Network Lighting Controls

26 2200 - Low-Voltage Transformers

26 2413 - Switchboards

26 2416 - Panelboards

26 2500 - Enclosed Bus Assemblies

26 2716 - Electrical Cabinets and Enclosures

26 2726 - Wiring Devices

26 2813 - Fuses

26 2819 - Enclosed Switches

26 2823 - Enclosed Circuit Breakers

26 2913 - Enclosed Controllers

26 5100 - Interior Lighting

26 5600 - Exterior Lighting

26 6111 - Theatrical Dimming and Controls

26 6120 - Company Switches

DIVISION 27 -- COMMUNICATIONS

27 0000 - Communications




00 0110-6

27 0529 - Hangers and Supports for Communications Systems

27 0533 - Conduits and Backboxes for Communications Systems

27 0537 - Firestopping, Smoke and Acoustical Sealing for Communications Systems

27 0553 - Identification for Communications Systems

27 1343 - Structrured Cabling System

27 4100 - Audio-Visual Systems

27 4119 - Portable Audio-Visual Equipment

DIVISION 28 -- ELECTRONIC SAFETY AND SECURITY

28 3100 - Fire Detection and Alarm

DIVISION 31 -- EARTHWORK

31 1000 - Site Clearing and Preparation

31 2000 - Earth Moving

31 2316 - Excavation

31 2316.13 - Trenching & Backfilling

31 3000 - Erosion & Sediment Control

31 4000 - Shoring & Underpinning

DIVISION 32 -- EXTERIOR IMPROVEMENTS (NOT USED)

APPENDIX

A. Geotechnical Engineering Report

B. Laboratory Testing

C. USGS Design Map Reports-Fault Parameters

D. Earthquake Induced Settlement Analysis

END OF SECTION



10/16/2019 ALTERNATES01 2300-1

SECTION 01 2300ALTERNATES

PART 1 GENERAL1.01 SECTION INCLUDES

A. Description of Alternates.1.02 RELATED REQUIREMENTS

A. Document 00 2113 - Instructions to Bidders: Instructions for preparation of pricing forAlternates.

B. Document 00 4213 - Alternat Bid Items Proposal: List of Alternates as supplement to Bid Form.1.03 ACCEPTANCE OF ALTERNATES

A. Alternates quoted on Bid Forms will be reviewed and accepted or rejected at Owner's option. Accepted Alternates will be identified in the Owner-Contractor Agreement.

B. Coordinate related work and modify surrounding work to integrate the Work of each Alternate.1.04 SCHEDULE OF ALTERNATES

A. Alternate No. 01 - Theatrical Lighting & Draperies:1. Section 11 6133 Theatrical Rigging, included in all TE, TL, TS, & AV drawings.2. Section 11 6143 Theatrical Draperies, included in all TE & TL drawings.3. Section 11 6191 Theatrical Lighting Instruments and Accessories, included in all TE & TL

drawings.a. Theatrical Pipe Grid, Dimming and Controls shall remain in base bid.

B. Alternate No. 02 - Theatre Equipment:1. Section 11 6113 Orchestra Enclosures, included in all TE & TL drawings2. Section 11 6173 Portable Dance Floor Surface, included in all TE drawings.3. Section 12 6211 Loose Audience Seating, including drawings T-TS011, T-TS021,

T-TS031 row EE Only4. Section 12 6623 Telescoping Seating Platforms, including drawings T-TS011,T-TS021,

T-TS031C. Alternate No. 03 - Audio Visual System:

1. Section 27 4119 Portable Equipment, no drawings2. Section 27 4100 AV System, included in all AVS drawings

a. Video infrastructure system and projector system shall remain in base bidb. AV Conduit infrastructure shall remain in base bid

PART 2 PRODUCTS - NOT USEDPART 3 EXECUTION - NOT USED

END OF SECTION



10/9/2019 STEEL RAILINGS05 5213-1

SECTION 05 5213STEEL RAILINGS


A. Wall mounted handrails.B. Stair railings and guardrails.C. Free-standing railings at steps and Drinking Fountains.

1.02 RELATED REQUIREMENTSA. Section 03 3000 - Cast-in-Place Concrete: Placement of anchors in concrete.B. Section 05 5100 - Metal Stairs: Handrails other than those specified in this section.C. Section 05 5100 - Metal Stairs: Attachment plates for handrails specified in this section.D. Section 09 2116 - Gypsum Board Assemblies: Placement of backing plates in stud wall

construction.E. Section 09 9113 - Exterior Painting: Paint finish.F. Section 09 9123 - Interior Painting: Paint finish.

1.03 REFERENCE STANDARDSA. AAMA 611 - Voluntary Specification for Anodized Architectural Aluminum; 2012.B. AAMA 2603 - Voluntary Specification, Performance Requirements and Test Procedures for

Pigmented Organic Coatings on Aluminum Extrusions and Panels (with Coil Coating Appendix);2015.

C. AAMA 2604 - Voluntary Specification, Performance Requirements and Test Procedures forHigh Performance Organic Coatings on Aluminum Extrusions and Panels; 2013.

D. AAMA 2605 - Voluntary Specification, Performance Requirements and Test Procedures forSuperior Performing Organic Coatings on Aluminum Extrusions and Panels; 2013.

E. ADA Standards - Americans with Disabilities Act (ADA) Standards for Accessible Design; 2010.F. AISC 201 - AISC Certification Program for Structural Steel Fabricators, Standard for Steel

Building Structures; 2006.G. ASTM A53/A53M - Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated,

Welded and Seamless; 2012.H. ASTM A123/A123M - Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and

Steel Products; 2015.I. ASTM A500/A500M - Standard Specification for Cold-Formed Welded and Seamless Carbon

Steel Structural Tubing in Rounds and Shapes; 2013.J. ASTM A501/A501M - Standard Specification for Hot-Formed Welded and Seamless Carbon

Steel Structural Tubing; 2014.K. ASTM B177/B177M - Standard Guide for Engineering Chromium Electroplating; 2011

(Reapproved 2017).L. ASTM B211 - Standard Specification for Aluminum and Aluminum-Alloy Rolled or Cold Finished

Bar, Rod, and Wire; 2012.M. ASTM B211M - Standard Specification for Aluminum and Aluminum-Alloy Rolled or

Cold-Finished Bar, Rod, and Wire (Metric); 2012.N. ASTM B241/B241M - Standard Specification for Aluminum and Aluminum-Alloy Seamless Pipe

and Seamless Extruded Tube; 2016.



10/9/2019 STEEL RAILINGS05 5213-2

O. ASTM B429/B429M - Standard Specification for Aluminum-Alloy Extruded Structural Pipe andTube; 2010e1.

P. ASTM B483/B483M - Standard Specification for Aluminum and Aluminum-Alloy Drawn Tubesfor General Purpose Applications; 2013, with Editorial Revision (2014).

Q. ASTM E935 - Standard Test Methods for Performance of Permanent Metal Railing Systemsand Rails for Buildings; 2013, with Editorial Revision.

R. ASTM E985 - Standard Specification for Permanent Metal Railing Systems and Rails forBuildings; 2000 (Reapproved 2006).

S. SSPC-Paint 15 - Steel Joist Shop Primer/Metal Building Primer; 1999 (Ed. 2004).T. SSPC-Paint 20 - Zinc-Rich Primers (Type I, "Inorganic," and Type II, "Organic"); 2002 (Ed.

2004).1.04 SUBMITTALS

A. See Section 01 3000 - Administrative Requirements, for submittal procedures.B. Shop Drawings: Indicate profiles, sizes, connection attachments, anchorage, size and type of

fasteners, and accessories.C. Samples: Submit One, 6 inch long samples of handrail at welded joints. Submit one samples

of elbow, wall bracket, and end stop.1.05 QUALITY ASSURANCE

A. Structural Designer Qualifications: Professional Structural Engineer experienced in design ofthis work and licensed in the State in which the Project is located, or personnel under directsupervision of such an engineer.

B. Welder Qualifications: Show certification of welders employed on the Work, verifying AWSqualification within the previous 12 months.

C. Fabricator Qualifications:1. A qualified steel fabricator that is certified by the American Institute for Steel Construction

(AISC) under AISC 201.PART 2 PRODUCTS2.01 RAILINGS - GENERAL REQUIREMENTS

A. Design, fabricate, and test railing assemblies in accordance with the most stringentrequirements of applicable local code.

B. Allow for expansion and contraction of members and building movement without damage toconnections or members.

C. Dimensions: See drawings for configurations and heights.1. Top Rails and Wall Rails: 1-1/2 inches diameter, round.

D. Provide anchors and other components as required to attach to structure, made of samematerials as railing components unless otherwise indicated; where exposed fasteners areunavoidable provide flush countersunk fasteners.1. For anchorage to stud walls, provide backing plates, for bolting anchors.

E. Provide welded joints to join lengths, seal open ends, and conceal exposed mounting bolts andnuts, including but not limited to elbows, T-shapes, splice connectors, flanges, escutcheons,and wall brackets.

2.02 STEEL RAILING SYSTEMA. Steel Tube: ASTM A500/A500M, Grade B cold-formed structural tubing.B. Steel Bar: Shall conform to ASTM A 36

1. Profile: 1/2"x1.5" Steel Bar - See Drawings2. Finish:



10/9/2019 STEEL RAILINGS05 5213-3

a. Exterior: Galvanizedb. Interior: Painted - Reference Spec Sec 090600-Schedule for Finishes

3. Fabrication: Factory- or shop-welded from matching steel bar; seams continuously welded;joints and seams ground smooth.

C. Exposed Fasteners: Flush countersunk screws or bolts; consistent with design of railing.D. Straight Splice Connectors: Steel concealed spigots.E. Wood Handrail Cover: Solid Wood

1. Profile: Rounded Section per Drawings2. Material: Walnut3. Finish: Gloss-Per Spec Sec 099123-Interior Painting

F. Galvanizing: In accordance with requirements of ASTM A123/A123M.1. Touch-Up Primer for Galvanized Surfaces: SSPC-Paint 20, Type I - Inorganic.

G. Shop and Touch-Up Primer: SSPC-Paint 15, complying with VOC limitations of authoritieshaving jurisdiction.

2.03 FABRICATIONA. Accurately form components to suit specific project conditions and for proper connection to

building structure.B. Fit and shop assemble components in largest practical sizes for delivery to site.C. Fabricate components with joints tightly fitted and secured. D. Welded Joints:

1. Exterior Components: Continuously seal joined pieces by continuous welds. Drillcondensate drainage holes at bottom of members at locations that will not encouragewater intrusion.

2. Interior Components: Continuously seal joined pieces by continuous welds.3. Grind exposed joints flush and smooth with adjacent finish surface. Make exposed joints

butt tight, flush, and hairline. Ease exposed edges to small uniform radius.E. Install continuous solid wood handrail cover. Use finger-joints at splices, sand smooth and

apply finish.PART 3 EXECUTION3.01 EXAMINATION

A. Verify that field conditions are acceptable and are ready to receive work.3.02 PREPARATION

A. Clean and strip primed steel items to bare metal where site welding is required.B. Supply items required to be cast into concrete or embedded in masonry with setting templates,

for installation as work of other sections.C. Apply one coat of bituminous paint to concealed aluminum surfaces that will be in contact with

cementitious or dissimilar materials.3.03 INSTALLATION

A. Install in accordance with DSA approved drawings and manufacturer's instructions.B. Install components plumb and level, accurately fitted, free from distortion or defects, with tight

joints.C. Install railings in compliance with ADA Standards for accessible design at applicable locations.D. Anchor railings securely to structure.E. Field weld anchors as indicated on shop drawings. Touch-up welds with primer. Grind welds

smooth.



10/9/2019 STEEL RAILINGS05 5213-4

F. Conceal anchor bolts and screws whenever possible. Where not concealed, use flushcountersunk fastenings.

3.04 TOLERANCESA. Maximum Variation From Plumb: 1/4 inch per floor level, non-cumulative.B. Maximum Offset From True Alignment: 1/4 inch.C. Maximum Out-of-Position: 1/4 inch.

END OF SECTION



10/9/2019 EXPANSION JOINT COVERASSEMBLIES

07 9513-1

SECTION 07 9513EXPANSION JOINT COVER ASSEMBLIES


A. Expansion joint cover assemblies for wall, ceiling, and roof surfaces.B. Interior wall expansion joint coversC. Interior ceiling expansion joint coversD. Roof expansion joint coversE. Exterior wall expansion joint covers

1.02 RELATED REQUIREMENTSA. Section 03 3000 - Cast in Place Concrete: Placement of joint cover assembly frames in

concrete.B. Section 04 2000 - Unit Masonry: Placement of joint cover assembly frames in masonry.C. Section 07 7100 - Roof Specialties: Roof expansion and control joint covers.D. Section 07 9200 - Joint Sealants: Sealing expansion and control joints using gunnable and

pourable sealants.E. Section 09 2116 - Gypsum Board Assemblies: Placement of expansion joint assemblies in

gypsum board walls and ceilings.F. Section 09 2405 - Portland Cement PlasterG. Section 09 5100 - Acoustical Ceilings: Expansion joint assemblies in suspended ceiling grids.

1.03 REFERENCE STANDARDSA. ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods,

Wire, Profiles, and Tubes; 2014.B. ASTM B221M - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods,

Wire, Profiles, and Tubes [Metric]; 2013.C. ASTM B308/B308M - Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural

Profiles; 2010.D. UL (DIR) - Online Certifications Directory; current listings at database.ul.com.

1.04 ADMINISTRATIVE REQUIREMENTSA. Installation Templates: For frames and anchors to be embedded in concrete or masonry,

furnish templates to relevant installers; include installation instructions and tolerances.1.05 SUBMITTALS

A. See Section 01 3000 - Administrative Requirements, for submittal procedures.B. Product Data: Provide joint assembly profiles, profile dimensions, anchorage devices and

available colors and finish.C. Shop Drawings: Indicate joint and splice locations, miters, layout of the work, affected adjacent

construction and anchorage locations.D. Samples: Submit two samples 6 inch long, illustrating profile, dimension, color, and finish

selected.E. Manufacturer's Installation Instructions: Indicate rough-in sizes and required tolerances for item

placement.




07 9513-2

PART 2 PRODUCTS2.01 MANUFACTURERS

A. Expansion Joint Cover Assemblies:1. Construction Specialties, Inc: www.c-sgroup.com/#sle.2. MM Systems Corp: www.mmsystemscorp.com/#sle.3. Nystrom, Inc: www.nystrom.com/#sle.

2.02 EXPANSION JOINT COVER ASSEMBLY APPLICATIONSA. Interior Non-Fire-Rated Wall/Ceiling Joints Subject to Seismic Movement:

1. Manufacturers:a. Construction Specialties, Inc; Flush Seismic Wall and Ceiling Coversb. MM Systems Corp @ Ceiling: VSG-500c. MM Systems Corp @ Wall: VSW-500 STUDd. Substitutions: See Section 01 6000 - Product Requirements.

B. Exterior Wall Joints Subject to Seismic Movement:1. Manufacturers:

a. MM Systems Corp @ Metal Stud Wall VSS-500-E STUD w/ Interior Seal # 9820b. MM Systems Corp @ Concrete-Masonry Wall VSS-500-E CONC w/ Interior Seal #

9821c. Substitutions: See Section 01 6000 - Product Requirements.

C. Roof expansion joint covers subject to Seismic Movement:1. Manufacturers:

a. MM Systems Corp @ Roof-to-Wall ERFL-500 w/ Interior Sealb. MM Systems Corp @ Roof-to-Roof ERF-500 w/ Interior Sealc. Substitutions: See Section 01 6000 - Product Requirements.

2.03 EXPANSION JOINT COVER ASSEMBLIESA. Expansion Joint Cover Assemblies - General: Factory-fabricated and assembled; designed to

completely fill joint openings, sealed to prevent passage of air, dust, water, smoke; suitable fortraffic expected.1. Joint Dimensions and Configurations: As indicated on drawings.2. Joint Cover Sizes: Selected to suit joint width and configuration, based on manufacturer's

published recommendations and limitations.3. Lengths: Provide covers in full lengths required; avoid splicing wherever possible.4. Anchors, Fasteners, and Fittings: Provided by cover manufacturer.

B. Resilient Seal Type Covers: Having flat exposed surface without crevices that could collect dirt;designed to withstand expected movement without extrusion of seal from joint assembly; forfloors, provide style that is flush with top of floor covering; for exterior joints, weathertight.

C. Covers In Gypsum Board Assemblies: Provide style with anchoring wings that can becompletely covered by joint compound.

2.04 MATERIALSA. Extruded Aluminum: ASTM B221 (ASTM B221M), 6063 alloy, T6 temper; or ASTM

B308/B308M, 6061 alloy, T6 temper.1. Exposed Finish Outdoors: Natural anodized.2. Exposed Finish at Walls and Ceilings: Natural anodized.

B. Resilient Seals:1. For Ceilings: Any resilient material, flush, pleated, or hollow gasket.2. Color: White.

C. Anchors and Fasteners: As recommended by cover manufacturer.

http://global.ihs.com/doc_detail.cfm?rid=BSD&document_name=ASTM%20B308/B308M










07 9513-3

D. Ferrous Metal Anchors: Galvanized where embedded in concrete or in contact withcementitious materials.

E. Threaded Fasteners: Stainless steel.F. Backing Paint for Aluminum Components in Contact with Cementitious Materials: Asphaltic

type.PART 3 EXECUTION3.01 EXAMINATION

A. Verify that joint preparation and dimensions are acceptable and in accordance withmanufacturer's requirements.

B. Verify that frames and anchors installed by others are in correct locations and suitable forinstallation of remainder of assembly.

3.02 INSTALLATIONA. Install components and accessories in accordance with manufacturer's instructions.B. Align work plumb and level, flush with adjacent surfaces.C. Rigidly anchor to substrate to prevent misalignment.

3.03 PROTECTIONA. Do not permit traffic over unprotected floor joint surfaces.B. Provide strippable coating to protect finish surface.

END OF SECTION





























10/16/2019 COILING COUNTER DOORS

08 3313-1

SECTION 08 3313

COILING COUNTER DOORS

PART 1 GENERAL

1.01 SECTION INCLUDES

A. Non-fire-rated coiling counter doors and operating hardware.

1.02 RELATED REQUIREMENTS

A. Section 06 1000 - Rough Carpentry: Rough openings.

B. Section 07 9200 - Joint Sealants: Sealing joints between frames and adjacent construction.

C. Section 08 7100 - Door Hardware: Cylinder cores and keys.

D. Section 09 2116 - Gypsum Board Assemblies: Rough openings.

E. Section 09 9123 - Interior Painting: Field paint finish.

F. Section 26 0533.13 - Conduit for Electrical Systems: Conduit from electric circuit to operatorand from operator to control station.

G. Section 26 0533.13 - Conduit for Electrical Systems: Conduit from fire alarm system.

H. Section 26 0583 - Wiring Connections: Power to disconnect.

1.03 REFERENCE STANDARDS

A. ASTM A653/A653M - Standard Specification for Steel Sheet, Zinc-Coated (Galvanized) orZinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process; 2015.

B. ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods,Wire, Profiles, and Tubes; 2014.

C. ITS (DIR) - Directory of Listed Products; current edition.

D. NFPA 80 - Standard for Fire Doors and Other Opening Protectives; 2016.

E. UL (DIR) - Online Certifications Directory; current listings at database.ul.com.

1.04 SUBMITTALS

A. See Section 01 3000 - Administrative Requirements, for submittal procedures.

B. Product Data: Submit manufacturer's standard literature showing materials and details ofconstruction and finish. Include data on electrical operation.

C. Shop Drawings: Indicate rough and actual opening dimensions, anchorage methods, hardwarelocations, and installation details.

D. Samples: Submit two slats, 4 inch long, illustrating shape, color and finish texture.

E. Operation and Maintenance Data: Indicate modes of operation, lubrication requirements andfrequency, and periodic adjustments required.

1.05 QUALITY ASSURANCE

A. Products Requiring Electrical Connection: Listed and classified by UL (DIR) as suitable for thepurpose specified and indicated.

PART 2 PRODUCTS

2.01 MANUFACTURERS

A. Coiling Counter Doors:

1. C.H.I. Overhead Doors; Model 6522 (steel): www.chiohd.com/#sle.

2. Cookson; Model: ESC10; 1901 South Litchfield Road, Goodyear, AZ 85338. Telephone:(800) 294-4358.

3. Substitutions: See Section 01 6000 - Product Requirements.




08 3313-2

2.02 COILING COUNTER DOORS

A. Coiling Counter Doors, Non-Fire-Rated: Aluminum slat curtain.

1. Mounting: Exterior face mounted.

2. Provide integral frame and sill of same material and finish.

3. Nominal Slat Size: 2 3/4 inches wide.

4. Slat Profile: Flat .

5. Finish, Aluminum: Anodized.

6. Guides: Formed track; same material and finish unless otherwise indicated.

7. Hood Enclosure: Manufacturer's standard; primed steel.

8. Manual hand chain lift operation.

B. Coiling Counter Doors, Fire-Rated: Galvanized steel slat curtain.

1. Mounting: Between jambs, within prepared opening.

2. Provide integral frame and sill of same material and finish.

3. Fire Rating: 3/4 hour; comply with NFPA 80.

a. Provide product listed and labeled by ITS (DIR) or UL (DIR) as suitable for thepurpose specified and indicated.

4. Nominal Slat Size: 1-1/4 inches wide.

5. Slat Profile: Flat.

6. Finish, Stainless Steel: No. 4 - Brushed.

7. Guides: Formed track; same material and finish unless otherwise indicated.

8. Hood Enclosure: Manufacturer's standard; primed steel.

9. Locking Devices: Chain lock keeper on inside.

2.03 MATERIALS

A. Curtain Construction: Interlocking, single thickness slats.

1. Slat Ends: Alternate slats fitted with end locks to act as wearing surface in guides and toprevent lateral movement.

2. Curtain Bottom: Fitted with angles to provide reinforcement and positive contact in closedposition.

3. Steel Slats: ASTM A653/A653M galvanized steel sheet, with minimum G90/Z275 coating;minimum thickness 16 gage, 0.06 inch.

4. Aluminum Slats: ASTM B221 (ASTM B221M), aluminum alloy Type 6063; minimumthickness 0.05 inch.

B. Guide Construction: Continuous, of profile to retain door in place, with mounting brackets ofsame metal.

1. Aluminum Guides: Extruded aluminum channel, with wool pile runners along inside.

C. Hood Enclosure: Internally reinforced to maintain rigidity and shape.

D. Lock Hardware:

1. Extruded aluminum tube bottom bar. Cylinder locking. Keyed on interior side of door

2. Latch Handle: Manufacturer's standard.

3. Manual Chain Lift: Provide padlockable chain keeper on guide.

E. Roller Shaft Counterbalance: Steel pipe and torsion steel spring system, capable of producingtorque sufficient to ensure smooth operation of curtain from any position and capable of holdingposition at mid-travel; with adjustable spring tension; requiring 25 lb nominal force to operate.

PART 3 EXECUTION

3.01 EXAMINATION

A. Verify that opening sizes, tolerances and conditions are acceptable.

3.02 INSTALLATION

A. Install units in accordance with manufacturer's instructions.




08 3313-3

B. Install fire-rated doors in accordance with NFPA 80.

C. Use anchorage devices to securely fasten assembly to wall construction and building framingwithout distortion or stress.

D. Securely and rigidly brace components suspended from structure. Secure guides to structuralmembers only.

E. Fit and align assembly including hardware; level and plumb, to provide smooth operation.

F. Install perimeter trim as indicated.

3.03 TOLERANCES

A. Maintain dimensional tolerances and alignment with adjacent work.

B. Maximum Variation From Plumb: 1/16 inch.

C. Maximum Variation From Level: 1/16 inch.

D. Longitudinal or Diagonal Warp: Plus or minus 1/8 inch per 10 ft straight edge.

3.04 ADJUSTING

A. Adjust operating assemblies for smooth and noiseless operation.

3.05 CLEANING

A. Clean installed components.

B. Remove labels and visible markings.

END OF SECTION



10/9/2019 GLAZED ALUMINUM CURTAINWALLS

08 4413-1

SECTION 08 4413GLAZED ALUMINUM CURTAIN WALLS


A. Aluminum-framed window wall, with vision glazing and metal infill panels.B. Metal Cladding & Brake MetalC. Column covers.D. Firestopping between curtain wall and edge of floor slab.

1.02 RELATED REQUIREMENTSA. Section 05 1200 - Structural Steel Framing: Steel attachment members.B. Section 05 5000 - Metal Fabrications: Steel attachment devices.C. Section 07 8400 - Firestopping: Firestop at system junction with structure.D. Section 07 9200 - Joint Sealants: Sealing joints between frames and adjacent construction.E. Section 08 4313 - Aluminum-Framed Storefront & Window Systems: Entrance framing and

doors.F. Section 08 8000 - Glazing.

1.03 REFERENCE STANDARDSA. CBC 2013, Chapter 24B. AAMA CW-10 - Care and Handling of Architectural Aluminum From Shop to Site; 2015.C. AAMA 501.1 - Standard Test Method for Water Penetration of Windows, Curtain Walls and

Doors Using Dynamic Pressure; 2017.D. AAMA 501.2 - Field Check of Metal Storefronts, Curtain Walls, and Sloped Glazing Systems for

Water Leakage; 2009.E. AAMA 609 & 610 - Cleaning and Maintenance Guide for Architecturally Finished Aluminum

(Combined Document); 2015.F. AAMA 611 - Voluntary Specification for Anodized Architectural Aluminum; 2012.G. AAMA 1503 - Voluntary Test Method for Thermal Transmittance and Condensation Resistance

of Windows, Doors and Glazed Wall Sections; 2009.H. ASTM A36/A36M - Standard Specification for Carbon Structural Steel; 2014.I. ASTM B209 - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate; 2014.J. ASTM B209M - Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate

[Metric]; 2014.K. ASTM B221 - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods,

Wire, Profiles, and Tubes; 2014.L. ASTM B221M - Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods,

Wire, Profiles, and Tubes [Metric]; 2013.M. ASTM C794 - Standard Test Method for Adhesion-In-Peel of Elastomeric Joint Sealants; 2015a.N. ASTM E283 - Standard Test Method for Determining the Rate of Air Leakage Through Exterior

Windows, Curtain Walls, and Doors Under Specified Pressure Differences Across theSpecimen; 2004 (Reapproved 2012).

O. ASTM E331 - Standard Test Method for Water Penetration of Exterior Windows, Skylights,Doors, and Curtain Walls by Uniform Static Air Pressure Difference; 2000 (Reapproved 2009).




08 4413-2

1.04 ADMINISTRATIVE REQUIREMENTSA. Coordinate with installation of other components that comprise the exterior enclosure.B. Preinstallation Meeting: Conduct a preinstallation meeting one week before starting work of this

section; require attendance by all affected installers.1.05 SUBMITTALS

A. See Section 01 3000 - Administrative Requirements, for submittal procedures.B. Product Data: Provide component dimensions, describe components within assembly,

anchorage and fasteners, internal drainage details, glazing, and infill.C. Shop Drawings: Indicate system dimensions, framed opening requirements and tolerances,

affected related Work, expansion and contraction joint location and details, and field weldingrequired.

D. Deferred Approval: Contractor shall submit details and calculations for window walls taller than10'-0" for AOR,SEOR, and DSA approval prior to fabrication.

E. All sealant joints shown om shop drawings/submittals shall be reviewed and approved by thesealant manufacturer or distributor. A written statement approving the application from thesealant manufacturer shall be submitted to the architect for review.

F. The sealant manufacturer's statement shall address adhesion and compatability of surfaceswhere sealant is used.

G. Samples: Submit two samples 4x4 inches in size illustrating finished aluminum surface,glazing, infill panels, and glazing materials.

H. Manufacturer's Certificate: Certify that the products supplied meet or exceed the specifiedrequirements.

I. Design Data: Provide framing member structural and physical characteristics and engineeringcalculations, and identify dimensional limitations; include load calculations at points ofattachment to building structure.

J. Field Quality Control Submittals: Report of field testing for water penetration and air leakage.K. Warranty: Submit manufacturer warranty and ensure forms have been completed in Owner's

name and registered with manufacturer.1.06 QUALITY ASSURANCE

A. Designer Qualifications: Design curtain wall and its structural support framing componentsunder direct supervision of a Professional Structural Engineer experienced in design of thiswork and licensed at the State in which the Project is located.

B. Manufacturer Qualifications: Company specializing in manufacturing products specified in thissection with not less than three years of documented experience.

C. Installer Qualifications: Company specializing in performing work of type specified and with atleast three years of documented experience.

1.07 MOCK-UPA. See Section 01 4000 - Quality Requirements, for general requirements for mock-ups.B. Locate on-site where directed by Architect; mock-up may not remain as part of the Work.C. Locate off-site where directed, and remove when directed.

1.08 DELIVERY, STORAGE, AND HANDLINGA. Handle products of this section in accordance with AAMA CW-10.B. Protect finished aluminum surfaces with wrapping. Do not use adhesive papers or sprayed

coatings that bond to aluminum when exposed to sunlight or weather.




08 4413-3

1.09 FIELD CONDITIONSA. Do not install sealants when ambient temperature is less than 40 degrees F. Maintain this

minimum temperature during and 48 hours after installation.1.10 WARRANTY

A. See Section 01 7800 - Closeout Submittals, for additional warranty requirements.B. Correct defective Work within a five year period after Date of Substantial Completion.C. Provide five year manufacturer warranty against failure of glass seal on insulating glass units,

including interpane dusting or misting. Include provision for replacement of failed units.D. Provide five year manufacturer warranty against excessive degradation of exterior finish.

Include provision for replacement of units with excessive fading, chalking, or flaking.PART 2 PRODUCTS2.01 BASIS OF DESIGN

A. Captured Glazed System; Not Ubitized, Field Assembled:1. Basis of Design: Arcadia T500-OPG3000: per DSA approved drawings2. Refer to Schedule: Window Types S4, S7 & S8

B. Substitutions: See Section 01 6000 - Product Requirements.1. For any product not identified as "Basis of Design", submit information as specified for

substitutions.2.02 WINDOW WALL

A. Aluminum-Framed Window Wall: Factory fabricated, factory finished aluminum framingmembers with infill, and related flashings, anchorage and attachment devices.1. Outside glazed, with pressure plate and mullion cover.2. Fabrication Method: Field fabricated stick system.3. Glazing Method: Field glazed system.4. Vertical Mullion Face Width: 2-1/4 inches.5. Vertical Mullion Depth From Face of Glazing to Back of Frame: 10 inches min.6. Finish: Reference Spec Sec 090600-Schedule for Finishes.

a. Factory finish surfaces that will be exposed in completed assemblies.b. Touch-up surfaces cut during fabrication so that no natural aluminum is visible in

completed assemblies, including joint edges.c. Coat concealed metal surfaces that will be in contact with cementitious materials or

dissimilar metals with bituminous paint.7. Provide flush joints and corners, weathersealed, accurately fitted and secured; prepared to

receive anchors; fasteners and attachments concealed from view; reinforced as requiredfor imposed loads.

8. Construction: Eliminate noises caused by wind and thermal movement, prevent vibrationharmonics, and prevent "stack effect" in internal spaces.

9. System Internal Drainage: Drain to the exterior by means of a weep drainage network anywater entering joints, condensation occurring in glazing channel, and migrating moistureoccurring within system.

10. Air and Vapor Seal: Maintain continuous air barrier and vapor retarder throughoutassembly, primarily in line with inside pane of glazing and inner sheet of infill panel andheel bead of glazing compound.

11. Perimeter Clearance: Minimize space between framing members and adjacentconstruction while allowing expected movement.

12. Preparation for Window Treatments: Provide reinforced interior horizontal head rail.B. Structural Performance Requirements: Design and size components to withstand the following

load requirements without damage or permanent set.




08 4413-4

1. Wind Loads: Refer to Sheet S1.00 for wind design critera and wind pressures.a. Design and size components to withstand the specified load requirements without

damageor permanent set, when tested in accordance with ASTM E330/E330M, usingloads 1.5 times the design wind loads and 10 second duration of maximum load.

b. Curtain wall manufacturer to provide internal steel reinforcing as required to meet thespecified deflection and design pressure.

c. All steel reinforcing shall be in compliance with DSA IR-24-2 provided in the appendix.d. Curtain wall / Storefront manufacturer to provide internal steel reinforcing as required

to meet specified design pressure, deflection and loads imposed on framing tosupport sunshade at window S8

2. Movement: Accommodate the following movement without damage to components ordeterioration of seals:a. Expansion and contraction caused by 180 degrees F surface temperature.b. Expansion and contraction caused by cycling temperature range of 170 degrees F

over a 12 hour period.c. Movement of curtain wall relative to perimeter framing.d. System shall not deflect more than 1/8" at center point, or 1/16" at the centerpoint of a

horizontal member, once deadload points have been established.C. Water Penetration Resistance on Manufactured Assembly: No uncontrolled water on indoor

face when tested as follows:1. Test Pressure Differential: 15 psf.2. Test Method: ASTM E331.

D. Dynamic Water Resistance: No water leakage when measured in accordance with AAMA501.1-94 with a dynamic test pressure of 15 psf.

E. Air Leakage Laboratory Test: Maximum of 0.06 cu ft/min sq ft of wall area, when tested inaccordance with ASTM E283 at 6.24 psf pressure differential across assembly.

F. Thermal Performance Requirements:1. Condensation Resistance Factor of Framing: 55, minimum, measured in accordance with

AAMA 1503.2. Thermal Transmittance (U-Value) in accordance with AAMA 1503.1-88 shall not be less

than .65 BTU,hr/degree F/SF unless noted otherwise in documents.2.03 COMPONENTS

A. Aluminum Framing Members: Tubular aluminum sections, thermally broken with interior sectioninsulated from exterior, drainage holes and internal weep drainage system.1. Cross-Section: As indicated on drawings and specifications.

B. Glazing: As specified in Section 08 8000.C. Infill Panels: Insulated, aluminum sheet face and back, with edges formed to fit glazing channel

and sealed.1. Basis of Design: Metal skin laminated spandrel panels as manufactured by Mapes

Architectural Panels, LLC, Lincoln, NE2. Face Sheet: Aluminum3. Finish

a. Exterior: Custom Kynarb. Interior: Standard Kynarc. Color: Reference Spec Sec 090600-Schedule for Finishes.

4. Panel Fabricationa. Exterior Substrate: Corelite (H.D.P.E.)b. Core: Isocyanuratec. Interior Substrate: Tempered Hardboardd. Tolerances - .8% of panels dimension length and width - (+/-) 1/16" thickness

http://global.ihs.com/doc_detail.cfm?rid=BSD&document_name=ASTM%20E331

http://www.aamanet.org/general.asp?sect=2&id=45

























08 4413-5

e. Panel Thickness - 1"f. R-Value - 6.11g. U-Value - 0.16

D. Metal Cladding & Brake Metal1. Aluminum: 20 gage, 0.032 inch minimum thickness, finish to match curtain wall framing

members.2. Stainless Steel: 18 gage, 0.050 inch minimum thickness with No. 4-Brushed finish using

320 grit for final polishing.E. Beam Covers: Aluminum, 20 gage, 0.032 inch minimum thickness, finish to match curtain wall

framing members.F. Shims: High-impact styrene plastic, for vertical or horizontal use.

1. Manufacturer: CRL Horseshoe Shims. CRL Shims2. Thickness: As required for proper levelling and setting of assembly.

2.04 MATERIALS A. Extruded Aluminum: ASTM B221 (ASTM B221M).B. Sheet Aluminum: ASTM B209 (ASTM B209M).C. Structural Steel Sections: ASTM A36/A36M; shop primed.D. Structural Supporting Anchors: See Section 05 1200.E. Structural Supporting Anchors Attached to Reinforced Concrete Members: Design for welded

attachment to weld plates embedded in concrete.F. Fasteners: Stainless steel; type as required or recommended by curtain wall manufacturer.G. Exposed Flashings: Aluminum sheet, 20 gage, 0.032 inch minimum thickness; finish to match

framing members.H. Concealed Flashings: Sheet aluminum, 26 gage, 0.017 inch minimum thickness.I. Firestopping: As specified in Section 07 8400.J. Weatherseal Sealant: Silicone, with adhesion in compliance with ASTM C794; compatible with

glazing accessories.K. Glazing Gaskets: Type to suit application to achieve weather, moisture, and air infiltration

requirements.L. Glazing Accessories: As specified in Section 08 8000.M. Single Source Responsibility: Obtain entrances, storefronts, ribbon walls, window walls, curtain

walls, window systems and finish through one source from a single manufacturer.2.05 FINISHES

A. Class II Natural Anodized Finish: AAMA 611 AA-M12C22A31 Clear anodic coating not lessthan 0.4 mils thick.

B. Color: Reference Spec Sec 090600-Schedule for Finishes.PART 3 EXECUTION3.01 EXAMINATION

A. Verify dimensions, tolerances, and method of attachment with other related work.B. Verify that curtain wall openings and adjoining air and vapor seal materials are ready to receive

work of this section.C. Verify that anchorage devices have been properly installed and located.























08 4413-6

3.02 INSTALLATIONA. Install curtain wall system in accordance with DSA approved drawings and manufacturer's

instructions.B. Attach to structure per DSA approved drawings and to permit sufficient adjustment to

accommodate construction tolerances and other irregularities.C. Provide alignment attachments and shims to permanently fasten system to building structure.D. Align assembly plumb and level, free of warp or twist. Maintain assembly dimensional

tolerances, aligning with adjacent work.E. Provide thermal isolation where components penetrate or disrupt building insulation.F. Install sill flashings. Turn up ends and edges; seal to adjacent work to form water tight dam.G. Touch-up minor damage to factory applied finish; replace components that cannot be

satisfactorily repaired.3.03 TOLERANCES

A. Maximum Variation from Plumb: 0.06 inches every 3 ft non-cumulative or 0.5 inches per 100 ft,whichever is less.

B. Maximum Misalignment of Two Adjoining Members Abutting in Plane: 1/32 inch.C. Sealant Space Between Curtain Wall Mullions and Adjacent Construction: Maximum of 3/4 inch

and minimum of 1/4 inch.3.04 FIELD QUALITY CONTROL

A. Provide services of curtain wall manufacturer's field representative to observe for properinstallation of system and submit report.

B. See Section 01 4000 - Quality Requirements, for general testing and inspection requirements.C. Water-Spray Test: Provide water spray quality test of installed curtain wall components in

accordance with AAMA 501.2 during construction process and before installation of interiorfinishes.1. Perform a minimum of two tests in each designated area as indicated on drawings.2. Conduct tests in each area prior to 10 percent and 50 percent completion of this work.

D. Repair or replace curtain wall components that have failed designated field testing, and retest toverify performance conforms to specified requirements.

3.05 ADJUSTINGA. Adjust operating sash for smooth operation.

3.06 CLEANINGA. Remove protective material from pre-finished aluminum surfaces.B. Wash down surfaces with a solution of mild detergent in warm water, applied with soft, clean

wiping cloths, take care to remove dirt from corners, and wipe surfaces clean.C. Upon completion of installation, thoroughly clean aluminum surfaces in accordance with AAMA

609 & 610.3.07 PROTECTION

A.END OF SECTION






10/9/2019 SCHEDULE FOR FINISHES09 0600-1

SECTION 09 0600SCHEDULE FOR FINISHES

PART 1 GENERAL1.01 SUMMARY

A. Section includes partial list of project finishes.1.02 PRODUCT OPTIONS

A. Products identified in this Section represent the basis of design and quality required for thisProject.1. To use an unnamed product, make a request for substitution following procedures in

Division 01 requirements for substitutions.2. Products proposed as substitutions shall have at least 10 comparable installations that

have been in place for 5 years, minimum, and remain in satisfactory condition.1.03 SUBMITTALS

A. Product Data: as specified in respective Section of this Manual. For proposed substitutions,accompany product data of proposed substitution with product data of specified material.

B. Samples: as specified in respective Section of this Manual. For proposed substitutions,accompany sample of proposed substitution with sample of specified material.

1.04 FINISH SCHEDULE NOTESA. Color selections are based on use of products specified in this Manual. If manufacturers, other

than those indicated, are used, Architect reserves the right to select color of the alternatematerial and revise color selections of other finishes to ensure proper coordination.

B. Paint Sheen Definitions1. Sheen 1: flat (5, or less, using an 85-degree gloss meter)2. Sheen 2: eggshell (10 to 20 using an 85-degree gloss meter)3. Sheen 3: satin (15 to 35 using a 60-degree gloss meter)4. Sheen 4: semi-gloss (30 to 65 using a 60-degree gloss meter)5. Sheen 5: high gloss (over 65 using a 60-degree gloss meter)6. Sheen 6: as manufactured

C. Paint Sheen Schedule. Unless scheduled or indicated otherwise, provide finish coats with thesheen ratings listed below. When the Paint finish ID Code contains a numerical extension ofthe color code, provide finish-coat with sheen indicated by that number, use definitions inSection 09 90 00.1. Concrete and concrete block walls: sheen 3 (Satin)2. Ceilings and soffits (gypsum, metal, concrete): sheen 1 (Flat)3. Gypsum board walls and partitions: sheen 2 or 3 (Eggshell / Satin)4. Hollow metal doors and frames: sheen 3 (Satin)5. Railings, stringers, risers, etc.: sheen 4 (Semi-gloss)6. Structural Steel & sheet metal: sheen 3 (Satin)7. Aluminum window & brake metal: sheen 4 (Semi-gloss)

D. Paint walls, scheduled to receive paint, color P-#, unless indicated otherwise.1. Where wall finish changes occur, terminate finishes at inside corners unless indicated

otherwise.E. Paint vents, grilles, access panels, plug strip, cabinet unit heaters, electrical panel boards (in

finished spaces) to match surface on which they occur unless indicated otherwise.1. Do not paint items with factory white finish, occurring in white AC-# or white gypsum board

ceilings.2. Do not paint stainless steel and brushed aluminum items.




F. Paint hollow metal doors and frames, scheduled to receive paint, to match surface in which theyoccur unless scheduled otherwise in Door Schedule.

G. Paint Ceilings scheduled to receive paint color P-#, unless indicated otherwise.H. Where changes in floor finish occur at door opening, locate change in flooring material directly

under centerline of closed door unless indicated otherwise. Where there is no door, centerchange in flooring material in opening, unless indicated otherwise.1. Provide resilient transition strip where flooring materials of different thicknesses meet,

unless indicated otherwise. Size strip to provide flush transition to both finishes.2. Provide SP # transition strip at transitions between wet and dry areas of ceramic tile finish

and at3. Provide metal edge strip at termination of carpet and tile at opening to utility spaces such

janitor’s- electrical- and communication-closets. Edge strip shall have beveled profilewhere flooring thickness exceeds 0.25-inch.

PART 2 PRODUCTS - NOT USEDPART 3 EXECUTION3.01 SCHEDULE OF CONCRETE FINISHES

A. 03 3511 –Concrete Floor Finishes1. Concrete Sealer - Acrylic

a. Manufacturer: Vexcon Starseal 1315b. Type: ASTM C1315 and C309, Type I clear, Class A, Acrylicc. Finish: Semi-gloss matte finish

2. CONC 1 – Field #1 (Interior, Vestibules & Ticket Booth)a. Colors

1) Cement: Natural2) Sand: Natural

b. Finish: Diamond Grind and Sealed3. CONC 2 – Field #2 (Interior, Storage and Mechanical)

a. Colors1) Cement: Natural2) Sand: Natural

b. Finish: Sealed3.02 SCHEDULE OF METAL FINISHES

A. 05 1200 – Structural Steel (Refer to 1.04C Paint Sheen Schedule for finish type)1. AESS - Architecturally Exposed Structural Steel @ Stair Stringers @ Control Booth

a. Color: P32. Exposed Structural Steel

a. Color: P3 U.N.O.B. 05 3100 – Steel Decking

1. Refer to Reflected Ceiling Plans for locations & Structural Drawings for Deck Typesa. Finish: Factory Primed, Finish P2

C. 05 5500 – Metal Fabrications1. Bent Plate

a. Color: Finished to Match P3 U.N.O.D. 05 5213 – Steel Railing

1. HRL 1 – Handraila. Railing Material: Steel Bar 1.5” x 0.5” - See Drawings for configuration and

dimensionsb. Finish:




1) Exterior: Galvanized2) Interior: Painted P3 U.N.O.

c. Handrail Cover:1) Material: Solid Wood2) Wood Species: Walnut3) Finish: Clear - Gloss

E. 05 7000 – Decorative Formed Metal Guardrails and Handrails (Refer to 1.04C Paint SheenSchedule for finish type)1. GRL 1 – Aluminum Panel Laser Cut Screen @ Drinking Fountain in MPR + Ramp

Guardrail.a. Manufacturer: BOK Modernb. Style: A36c. Color: To Match P1d. Finish: Aluminum, Kynar finishe. Thickness: 3/16”

3.03 SCHEDULE OF WOOD, PLASTIC AND COMPOSITE FINISHESA. 06 2000 – Finish Carpentry

1. WD 1 – Wood Veneer @ Acoustic Panelsa. Manufacturer: Bacon Veneer Companyb. Finish: Plain Sliced Maplec. Stain: Clear

2. WD 2 - Pressure Sensitive Veneer@ Acoustic Wall Panels, Acoustic Ceiling Panels &Acoustical Deflectorsa. Manufacturer: Formwood Industriesb. Finish: Plain Sliced Maplec. Stain: Clear

B. 06 4100 – Architectural Wood Casework1. Exposed Interior Surfaces:

a. WD-1b. Manufacturer: Bacon Veneer Companyc. Finish: Plain Sliced Mapled. Stain: Clear

2. Semi-Exposed Surfaces:a. WD-1b. Manufacturer: Bacon Veneer Companyc. Finish: Plain Sliced Mapled. Stain: Clear

3. Concealed Interior Surfaces:a. LPDLb. Low-Pressure Decorative Laminatec. Melamined. Color: White

3.04 SCHEDULE OF EXTERIOR FINISHESA. 07 6200 – Sheet Metal Flashing and Trim

1. MTL 2 – Sheet Metal at Roofsa. Finish: To Match Adjacent Surface & Painted Structure, See Exterior Elevations

where applicable.3.05 SCHEDULE OF OPENING FINISHES

A. 08 1113 – Hollow Metal Doors & Frames




1. Exterior Framesa. Manufacturer: PPG Industries, Inc.b. Finish: Gloss (paint finish to be sprayed not brushed or rolled)c. Color: Match P3 at Ticket Booth (See Architectural Drawings and Door Schedule)

2. Interior Framesa. Finish: Gloss (paint finish to be sprayed not brushed or rolled)b. Color: Match P3 at Ticket Booth (See Architectural Drawings and Door Schedule)

3. Exterior Doorsa. Manufacturer: PPG Industries, Inc.b. Finish: Semi-gloss (paint finish to be sprayed not brushed or rolled)c. Color: Match P3 at Ticket Booth (See Architectural Drawings and Door Schedule)

4. Interior Doorsa. Manufacturer: PPG Industries, Inc.b. Finish: Semi-gloss (paint finish to be sprayed not brushed or rolled)c. Color: See Architectural Drawings and Door Schedule

B. 08 1425 – Clad Wood Doors1. WD 1 - Interior Doors

a. Manufacturer: Doormerica Productsb. Style: American Series, Extra Heavy Duty with glass lite as occurs, See Door Type

Elevationsc. Species: Mapled. Cut: Plain Slicede. Stain / Finish: Clear

C. 08 4313 – Aluminum-Framed Storefront & Window Systems1. Exterior Frames & Doors

a. Manufacturer: Arcadiab. Finish: P3 @ Multi-Purpose Buildingc. Match color P3 at Ticket Boothd. Brake Metal Panels Colors: For locations & colors, see Window Type Elevations

D. 08 4413 – Glazed Aluminum Curtainwall1. Exterior Frames & Doors

a. Manufacturer: Arcadiab. Color: Match P3 at Ticket Booth @ Multi-Purpose Building

E. 08 8000 – Glazing1. G 1 - Glass: Glass Units – Vision Glazing (Typical @ Exterior)2. G 2 - Glass: Spandrel with Acid Etch Finish3. G 3 - Glass: Insulated, Laminated Safety Glass4. G 4 - Glass: Monolithic Interior Vision Glazing

3.06 SCHEDULE OF INTERIOR FINISHESA. 09 2405 – Portland Cement Plaster

1. ES 1 - Exterior Stucco 1: Typicala. Manufacturer: La Habrab. Finish: Sand Lightc. Color: Match Existing (VIF) Dunn Edwards - Heather: DEC 773d. Texture: Smooth

B. 09 3000 – Tiling1. CTB 1 - Ceramic Tile Base Type 1: Toilet Rooms

a. Manufacturer: Mosab. Style: Coved Skirtingc. Color: TBD




d. Size: 6”x6” cove base (with inside & outside corners)e. Grout:

1) Manufacturer: Custom Building Products2) Color: TBD

2. CT 1 - Ceramic Tile: Base Type 2: Toilet Roomsa. Manufacturer: Mosab. Style: Quartzc. Color: 4103Vd. Size: 24”x24”e. Grout:


3. CT 2 - Ceramic Tile: Floor Tile – Toilet Roomsa. Manufacturer: Mosab. Style: Murals Blendc. Pattern: PT3452-1059d. Finish: 30010 Stonematt 30510: Plain Glosse. Size: 6” x 6”f. Grout:


4. CT 3 – Ceramic Tile: Floor Tile – Toilet Rooms Accentsa. Manufacturer: Mosab. Style: Colors, Global Collection, Globalgripc. Pattern: PT3452-1056d. Finish: Plain Glosse. Size: 6” x 6”f. Grout:


C. 09 5100 – Suspended Acoustical Ceilings – Lay-In1. AC 1 - Acoustic Ceiling System: MPR

a. Panel:1) Manufacturer: Armstrong2) Color: White3) Style: 5/8" Square Lay-In Cortega4) Size: 24” x 24”

b. Suspension System1) Manufacturer: Armstrong2) Style: 15/16" Prelude Tegular3) Color: Factory Painted White

2. AC 2 - Acoustic Ceiling System: Corridora. Panel:

1) Manufacturer: Armstrong2) Color: White3) Style: 5/8" Rectangular Lay-In Cortega4) Size: 24" x 48"

b. Suspension System1) Manufacturer: Armstrong2) Grid: 15/16” Prelude Plus XL3) Color: Factory Painted White




D. 09 6480 - Wood Stage Flooring1. Top Finish Material: 1/4" thick Tempered Hardboard2. Finish: Smooth Painted3. Color: Black4. Sheen: Semi-Gloss

E. 09 6500 – Resilient Flooring1. LVT 1 – Hallways and Common Areas

a. Manufacturer: Gerflorb. Style: Sagac. Color: 0032 Mozaic Greyd. Thickness: 4.6mm

2. LVT 2 – Multi-Purpose Rooma. Manufacturer: Mohawk Groupb. Style: Matuto Plusc. Color: Frostbite 915d. Pattern: Custom (See Finish Plan)e. Thickness: 2.5mm

3. LVT 3 – Multi-Purpose Rooma. Manufacturer: Mohawk Groupb. Style: Matuto Plusc. Color: Agreeable Grey 926d. Pattern: Custom (See Finish Plan)e. Thickness: 2.5mm

4. LVT 4 – Multi-Purpose Rooma. Manufacturer: Mohawk Groupb. Style: Matuto Plusc. Color: Sonic Silver 927d. Pattern: Custom (See Finish Plan)e. Thickness: 2.5mm

5. LVT 5 – Multi-Purpose Rooma. Manufacturer: Mohawk Groupb. Style: Matuto Plusc. Color: Grey Granite 959d. Pattern: Custom (See Finish Plan)e. Thickness: 2.5mm

6. LVT 6 – Multi-Purpose Rooma. Manufacturer: Mohawk Groupb. Style: Matuto Plusc. Color: Lemon Twist 131d. Pattern: Custom (See Finish Plan)e. Thickness: 2.5mm

7. LVT 7 – Multi-Purpose Rooma. Manufacturer: Mohawk Groupb. Style: Matuto Plusc. Color: Outrageous Orange 252d. Pattern: Custom (See Finish Plan)e. Thickness: 2.5mm

8. LVT 8 – Multi-Purpose Rooma. Manufacturer: Mohawk Groupb. Style: Matuto Plusc. Color: Red Hot 353




d. Pattern: Custom (See Finish Plan)e. Thickness: 2.5mm

9. B 1 - Rubber Base Type 1:a. Manufacturer: Johnsoniteb. Style: BaseWorks Thermoset Rubber Wall Basec. Color: 48 Grey WGd. Height: 4”

F. 09 6813 – Tile Carpeting1. C 1 - Carpet Type 1: Control Room

a. Manufacturer: Mohawk Groupb. Style: Renegade Collection - BT355 Riot QS Tilec. Color: 999 Leather Jacketd. Pattern: Ashlar

G. 09 7200 – Wall Coverings1. WC 1 - Wallcovering Type 1: Graphic Wallpaper

a. Manufacturer: Blik (whatisblik.com)b. Style: TBDc. Color: TBDd. Image: Custom Graphic (five (5) custom images to be provided by Architect)e. Finish: Fine Texture

2. WC 2 - Wallcovering: Natural Wood veneera. Manufacturer: Hokusan Ltdb. Material: Maple

H. 09 9000 – Painting and Coating (Refer to 1.04C Paint Sheen Schedule for finish type, UNObelow):1. P 1 Interior Paint Color 1: Field Wall Color

a. Manufacturer: Sherwin Williamsb. Color: SW 7102 White Flourc. Finish: Eggshell (Semi-Gloss @ Restrooms & Kitchen)

2. P 2 Paint Color 2: Typical Ceilings: Gyp. Board and Exposed Deck, (see 05 70 00)a. Manufacturer: Sherwin Williamsb. Color: SW 7005 Pure Whitec. Finish: Semi-Gloss at Restrooms & Kitchen Ceilings.

3. P 3 Paint Color 4: Typical Fascia: Bent Plate (see Section 05 75 00), Door Framesa. Manufacturer: Sherwin Williamsb. Color: SW 7075 Web Grayc. Finish: Satin

4. P 4 Paint Color 5: Back Stage and Stage Floora. Manufacturer: Sherwin Williamsb. Color: SW 6258 Tricorn Blackc. Finish: Satin

5. P 5 Paint Color 6: Accenta. Manufacturer: Sherwin Williamsb. Color: SW 6903 Cheerfullc. Finish: Satin

6. P 6 Paint Color 7: Accenta. Manufacturer: Sherwin Williamsb. Color: SW 6881 Cayennec. Finish: Satin

7. P 7 Paint Color 7: Accenta. Manufacturer: Sherwin Williams




b. Color: SW 6501 Manitou Bluec. Finish: Satin

3.07 SCHEDULE OF SPECIALTY FINISHESA. 10 1400 – Signage

1. Tactile Plastic Signsa. Manufacturer: ASI Signageb. Manufacturer: ASI Signagec. Style: Digital high pressure laminate (ADA-Ready)d. Size: 12”x6”e. Font: Corbel

1) Color: White or Black letters2) Style: Bold3) Background:

(a) Color: Multiple custom digital images to be provided by architect duringsubmittals

2. Non-Tactile Plastic Signs:a. Manufacturer: ASI Signageb. Style: InTouch (ADA-Ready)c. Non-Tactile Plastic Signs:

1) Manufacturer: ASI Signage2) Style: Digital high pressure laminate (ADA-Ready)3) Size: 12”x6”4) Font: Corbel

(a) Color:White or Black letters(b) Style:Bold(c) Size:(d) Background:

(1) Color: Multiple custom digital images to be provided by architect duringsubmittals

3. Dimensional Letters: Powder Coated Aluminuma. Manufacturer: ASI Signageb. Style:c. Size: Varies, See Exterior Elevationsd. Font: Ariale. Color: Sherwin Williams: Manitou Blue SW 6501

4. Restroom Signsa. Tactile Plastic (wall mounted) Signs

1) Manufacturer: ASI Signage2) Style: InTouch (ADA-Ready)3) Size: 6”x6”4) Font: TBD5) Color:6) Background:

(a) Color:5. Photoluminescent Exit Signs:

a. Manufacturer: ESW Exit Sign Warehouse; [email protected]; (888)953-3948

b. Size: 8-1/2"x16"c. Model: ESW-PL75WLd. Color: Greene. Locations: As Indicated on Drawings




B. 10 2113 – Plastic Toilet Compartments1. TCP 1 - Toilet Compartments Type 1:

a. Manufacturer: Scranton Productsb. Style: 1" HDPEc. Color: Paisley Orange Peal

3.08 SCHEDULE OF FURNISHING FINISHESA. 12 2400 – Roller Shade System

1. WT 1 – Glare Reduction Shadea. Operation: Manualb. Manufacturer: Mechoshadec. Finish: SoHo Series 3% opennessd. Size: Refer to drawings for locations and size.e. Color: 1619 Sullivanf. Color: 0812 Charcoal

2. WT 2 – Room Darkening Shadea. Operation: Manualb. Manufacturer: Mechoshadec. Finish: SoHo Series 1% opennessd. Size: Refer to drawings for locations and size.e. Color: 1619 Sullivanf. Color: 0812 Charcoal

3. WT 4 – Glare Reduction Shadea. Operation: Motorizedb. Manufacturer: Mechoshadec. Finish: SoHo Series 1% opennessd. Style: Motorized roller shade & facia ‘Mecho5X’ sealed Heme. Size: Refer to drawings for locations and size.f. Color: 1619 Sullivang. Color: 0812 Charcoal

B. 12 3600 – Countertops1. PL 1 - Plastic Laminate: Counter Tops @ Control Room

a. Manufacturer: Nevamarb. Color: Jet Black - S6053Tc. Finish: Satin

2. SP 1 - Solid Polymer: Counter Tops @ Ticket Bootha. Manufacturer: Avoniteb. Color: Cement 8425c. Finish: Satin

3.09 SCHEDULE OF CONVEYING EQUIPMENT FINISHESA. 14 4216 – Vertical Wheelchair Lift

1. Manufacturer: Ascension-Lifta. Style: Vertical Platform Protege (42" Rise max)b. Style: Vertical Platform Clarity (168" Rise max)

1) Floor – Refer to 09 68 16 – Sheet Carpet, C1END OF SECTION



10/9/2019 WOOD STAGE FLOORING09 6460-1

SECTION 09 6460WOOD STAGE FLOORING


A. Wood Stage Flooring.B. Subflooring.C. Sleepers.D. Resilient cushioning.E. Sheet vapor retarder.

1.02 RELATED REQUIREMENTSA. Section 01 6116 - Volatile Organic Compound (VOC) Content Restrictions - Volatile Organic

Compound (VOC) Content Restrictions.B. Section 03 3000 - Cast-in-Place Concrete: Concrete subfloor surface; recessed.C. Section 06 1000 - Rough Carpentry: Subfloor blocking.D. Section 09 0561 - Common Work Results for Flooring Preparation: Concrete slab moisture and

alkalinity testing and remediation procedures.E. Section 09 9123 - Interior Painting: Product requirements for surface finish materials for

application in this section.1.03 REFERENCE STANDARDS

A. ASTM F710 - Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring;2011.

B. ASTM F1869 - Standard Test Method for Measuring Moisture Vapor Emission Rate of ConcreteSubfloor Using Anhydrous Calcium Chloride; 2011.

C. ASTM F2170 - Standard Test Method for Determining Relative Humidity in Concrete FloorSlabs Using in situ Probes; 2017.

D. MFMA (PUR) - Performance and Uniformity Rating Sport Specific Standards; current edition.E. MFMA (SPEC) - Guide Specifications for Maple Flooring Systems; current edition.

1.04 SUBMITTALSA. See Section 01 3000 - Administrative Requirements, for submittal procedures.B. Product Data: Provide data for flooring, floor finish materials, and resilient cushion.C. Shop Drawings: Indicate floor joint pattern and termination details.

1. Indicate provisions for expansion and contraction, wall base, and game insert or socketdevices.

2. Indicate size and type fasteners and anchors.D. Concrete Subfloor Test Report: Submit a copy of the moisture and alkalinity (pH) test reports.E. Installation Instructions: Indicate standard and special installation procedures.F. Maintenance Data: Include maintenance procedures and recommended maintenance

materials.G. Installer's Qualification Statement.H. Maintenance Materials: Furnish the following for Owner's use in maintenance of project.

1. See Section 01 6000 - Product Requirements, for additional provisions.1.05 QUALITY ASSURANCE

A. Perform work of this section in accordance with MFMA (SPEC).




B. Installer Qualifications: Company specializing in installing products specified in this section.1. Minimum three years of documented experience.

1.06 MOCK-UPA. Construct mock-up of wood flooring including subflooring, resilient cushioning, and hardboard.

Illustrate final finish.B. Size of mock-up to be not less than 12 inch long by 12 inch wide.C. See Section 01 4000 - Quality Requirements for additional requirements.D. Locate where directed.

1.07 DELIVERY, STORAGE, AND HANDLINGA. Deliver materials and store off the floor in a well-ventilated, weather-tight space.

1.08 FIELD CONDITIONSA. Do not install wood flooring until wet construction work is complete and permanent heat and air

conditioning is installed and operating.B. Maintain room temperature between 55 degrees F and 75 degrees F and relative humidity

between 35 to 50 percent for a period of seven days prior to delivery of materials to installationspace, during installation, and after installation.

C. Acclimate wood flooring materials to installation space a minimum of 48 hours prior toinstallation.

PART 2 PRODUCTS2.01 WOOD STAGE FLOORING

A. General: Wood Panel flooring, MFMA (PUR) compliant for application indicated; systemcomponents provided by single manufacturer.

B. Application: Performance stage.C. System Description:

1. Fixed, double layer subfloor system, wood panel flooring with tempered hardboard topmaterial-painted.

2.02 COMPONENTSA. Finish Surface Material

1. Tempered Hardboarda. Panel Thickness: 1/4"b. Panel Size: 4' x 8'c. Surface Finish: Smooth-Painted

B. Sleepers:1. Length: 96 inches.2. Softwood lumber, 2 by 4 inch nominal.

C. Subflooring: Two layers of 23/32 inch thick plywood, APA rated, exposure 1, minimum spanrating of 48/24.

D. Resilient Cushioning: Manufacturer's standard rubber pads, factory-applied to bottom side of subflooring.

E. Acoustic Insulation: Fill voids between sleepers with sound attenuation batt insualtion.F. Vapor Retarder: Polyethylene sheet, 6 mil thick; 2 inch wide tape for sealing sheet seams.G. Fasteners and Anchors: Manufacturer's standard type and size to suit application.

2.03 FINISHESA. Floor Finishes: Specified in Section 09 9000 - Painting & Coating




2.04 ACCESSORIESA. Edge Strip: Angle; mill finish aluminum.B. Transition Strip: Same species and finish as flooring material; profiles indicated.C. Adhesives: Types recommended by flooring manufacturer.

PART 3 EXECUTION3.01 EXAMINATION

A. Verify existing conditions before starting this work.B. Verify that concrete subfloor surface is smooth and flat to plus or minus 1/4 inch in 10 feet.C. Verify that required floor-mounted utilities are in correct location.

3.02 PREPARATIONA. Prepare substrate to receive wood flooring in accordance with manufacturer's and MFMA

instructions.B. Vacuum clean substrate.

3.03 INSTALLATIONA. Place vapor retarder over concrete surface, overlap seams a minimum of 6 inches and seal with

tape.B. Sleepers with Plywood Subfloor:

1. Place sleepers at 90 degree angle to direction of finished floor; space 12 inches on center. Stagger end joints a minimum of 24 inches.

2. Anchor sleepers to concrete substrate with steel anchoring pins.3. Fasten plywood subfloor over sleepers at 90 degree angle to direction of finished floor.

Allow minimum 1/4 inch between plywood subfloor edges.C. Double Layer Plywood Subfloor:

1. Place first layer at 90 degree angle to direction of finished floor, resilient pad side down.2. Fasten second layer (without pads) at 90 degree angle to first layer.3. Allow 1/4 inch between plywood subfloor edges.

D. Install solid blocking at doorways, under locations of heavy equipment, and as shown ondrawings, in accordance with flooring manufacturer's recommendations.

E. Install base at floor perimeter to cover expansion space. Miter inside corners.3.04 CLEANING

A. Clean floor surfaces in accordance with floor finish manufacturer's instructions.3.05 PROTECTION

A. Prohibit traffic on finished floor for 72 hours after installation.B. Place protective coverings over finished floors; do not remove coverings until Date of

Substantial Completion.END OF SECTION



10/9/2019 SOUND-ABSORBING WALLPANELS

09 8433.11-1

SECTION 09 8433.11SOUND-ABSORBING WALL PANELS


A. Sound-absorbing panels.B. Mounting accessories.

1.02 RELATED REQUIREMENTSA. Section 06 4100 - Architectural Wood Casework.B. Section 09 9123 - Interior Painting.

1.03 REFERENCE STANDARDSA. ASTM C423 - Standard Test Method for Sound Absorption and Sound Absorption Coefficients

by the Reverberation Room Method; 2009a.B. ASTM E84 - Standard Test Method for Surface Burning Characteristics of Building Materials;

2015a.C. ASTM E795 - Standard Practices for Mounting Test Specimens During Sound Absorption

Tests; 2005 (Reapproved 2012).1.04 SYSTEM DESCRIPTION

A. Performance Requirements:1. Surface Burning Characteristics (ASTM E84):

a. Flamespread: 25 maximum.b. Smoke Developed: 450 maximum.c. Fire ratings for all fabric covered panels is based on testing of the panel wrapped with

the standard in stock fabric, Guilford of Maine, FR 701 Style 2100.1.05 SUBMITTALS

A. See Section 01 3000 - Administrative Requirements, for submittal procedures.B. Product Data: Manufacturer's printed data sheets for products specified.C. Shop Drawings: Fabrication and installation details, panel layout, and fabric orientation.D. Selection Samples: Manufacturer's color charts for fabric covering, indicating full range of

fabrics, colors, and patterns available.E. Verification Samples: Fabricated samples of each type of panel specified; 12 by 12 inch,

showing construction, edge details, and fabric covering.F. Test Reports: Certified test data from an independent test agency verifying that panels meet

specified requirements for acoustical and fire performance.G. Maintenance Materials: Furnish the following for Owner's use in maintenance of project.

1. See Section 01 6000 - Product Requirements, for additional provisions.2. Extra Panels: Quantity equal to 5 percent of total installed, but not less than one of each

type.1.06 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company with not less than five years of experience inmanufacturing acoustical products similar to those specified.

1.07 DELIVERY, STORAGE, AND HANDLINGA. Protect acoustical units from moisture during shipment, storage, and handling. Deliver in

factory-wrapped bundles; do not open bundles until units are needed for installation.B. Store units flat, in dry, well-ventilated space; do not stand on end.




09 8433.11-2

C. Protect edges from damage.1.08 MOCK-UP

A. See Section 01 4000 - Quality Requirements, for additional mock-up requirements.B. Construct mock-up of acoustical units at location as indicated by Architect.

1. Minimum mock-up dimensions; 96 by 96 inches.2. Approved mock-up may remain as part of the Work.

1.09 PROJECT CONDITIONSA. Environmental Requirements: Do not install panels until wet work, such as concrete and

plastering, is complete; the building is enclosed; and the temperature and relative humidity arestabilized at 60 - 80 degrees F (16 - 27 degrees C) and 35% MINIMUM RH and 55% MAXIMUMRH, respectively. All products constructed with wood or wood fiber content must be stored forat least 72 hours in the controlled environment specified herein prior to installation to allow thematerials to stabilize.

PART 2 PRODUCTS2.01 FABRIC-COVERED SOUND-ABSORBING UNITS

A. Manufacturer - Basis of Design:1. Kinetics Noise Control, Inc.

a. Contact: PO Box 655, 6300 Irelan Place, Dublin, OH 43017; Telephone: (614)889-0480; Fax: (614) 889-0540; E-mail: [email protected]; Web site:www.kineticsnoise.com.

2. Substitutions: See Section 01 6000 - Product Requirements.B. Sound Absorbing Units: Prefinished, factory assembled fabric-covered panels.

1. Surface Burning Characteristics: Flame spread index of 25 or less and smoke developedindex of 450 or less, when tested in accordance with ASTM E84.

C. Fabric-Covered Acoustical Panels for Walls:1. Panel Core: Manufacturer's standard rigid or semi-rigid fiberglass core.2. Core Density: 6 to 7 lb/cu ft.3. Noise Reduction Coefficient (NRC): 1.00 when tested in accordance with ASTM C423 for

Type back-mounted with mechanical fasteners mounting, per ASTM E795.4. Panel Size: 24 inches by 48 inches.5. Panel Thickness: 2 inches.6. Edges: Perimeter edges reinforced by a formulated resin hardener.7. Corners: Radiused.8. Fabric: Woven polyester.9. Color: Reference Spec Sec 090600-Schedule for Finishes.10. Mounting Method: Back-mounted with mechanical fasteners.

2.02 FABRICATIONA. Fabric Wrapped, General: Fabricate panels to sizes and configurations as indicated, with fabric

facing installed without sagging, wrinkles, blisters, or visible seams.1. Where radiused or mitered corners are indicated, install fabric to avoid seams or gathering

of material.B. Tolerances: Fabricate to finished tolerance of plus or minus 1/16 inch for thickness, overall

length and width, and squareness from corner to corner.2.03 ACCESSORIES

A. Spline-Mounting Accessories: Manufacturer's standard concealed connecting splines ofextruded aluminum designed for screw attachment to walls, with coordinating moldings and trimfor interior and exterior corners and miscellaneous conditions.1. Color of Exposed Trim: To match fabric.




09 8433.11-3

B. Back-Mounting Accessories: Manufacturer's standard accessories for concealed support,designed to allow panel removal, and as follows:1. Two-part clip and base-support bracket system; brackets designed to support full weight of

panels and clips designed for lateral support, with one part mechanically attached to backof panel and the other attached to substrate.

2. Metal impaling clips designed to support full weight of panels, mechanically attached tosubstrate and adhesively bonded to back of panels.

C. Trim Moldings: Manufacturer's standard wood trim moldings for concealing panel joints; coloras selected from manufacturer's standards.

D. Fixing Clips: Manufacturers standard for application as indicated.E. Furring Strips: 1 by 2 inch wood furring.F. Panel Adhesive: Acceptable to acoustical panel manufacturer for application as indicated.

PART 3 EXECUTION3.01 EXAMINATION

A. Examine substrates for conditions detrimental to installation of acoustical units. Proceed withinstallation only after unsatisfactory conditions have been corrected.

3.02 INSTALLATIONA. Install acoustical units in locations as indicated, following manufacturer's installation

instructions.B. Align panels accurately, with edges plumb and top edges level. Scribe to fit accurately at

adjoining work and penetrations.3.03 CLEANING

A. Clean fabric facing upon completion of installation from dust and other foreign materials,following manufacturer's instructions.

3.04 PROTECTIONA. Provide protection of installed acoustical panels until Date of Substantial Completion.B. Replace panels that cannot be cleaned and repaired to satisfaction of the Architect.

END OF SECTION



10/9/2019 EXTERIOR PAINTING09 9113-1

SECTION 09 9113EXTERIOR PAINTING

PART 1 - GENERAL1.01 RELATED DOCUMENTS

A. Drawings and general provisions of the Contract, including General and SupplementaryConditions and Division 01 Specification Sections, apply to this Section.

1.02 SUMMARYA. Section includes surface preparation and the application of paint systems on the following

exterior substrates:1. Concrete.2. Fiber-cement board.3. Concrete masonry units (CMU).4. Steel.5. Galvanized metal.6. Aluminum (not anodized or otherwise coated).7. Stainless-steel flashing.8. Wood.9. Plastic trim fabrications.10. Exterior portland cement plaster (stucco).11. Exterior gypsum board.

1.03 RELATED REQUIREMENTS:A. Section 01 6116 - Volatile Organic Compound (VOC) Content Restrictions.B. Section 05 5000 - Metal Fabrications: Shop-primed items.C. Section 05 5100 - Metal Stairs: Shop-primed items.D. Section 09 9600 - High-Performance Coatings.E. Section 21 0553 - Identification for Fire Suppression Piping and Equipment: Painted

identification.F. Section 21 0553 - Identification for Fire Suppression Piping and Equipment: Color coding

scheme for items to be painted under this section.G. Section 22 0553 - Identification for Plumbing Piping and Equipment: Painted identification.H. Section 22 0553 - Identification for Plumbing Piping and Equipment: Color coding scheme for

items to be painted under this section.I. Section 23 0553 - Identification for HVAC Piping and Equipment: Painted identification.J. Section 23 0553 - Identification for HVAC Piping and Equipment: Color coding scheme for

items to be painted under this section.K. Section 26 0553 - Identification for Electrical Systems: Painted identification.L. Section 26 0553 - Identification for Electrical Systems: Color coding scheme for items to be

painted under this section.M. Section 32 1723.13 - Painted Pavement Markings: Painted pavement markings.

1.04 ACTION SUBMITTALSA. Product Data: For each type of product. Include preparation requirements and application

instructions.1. Indicate VOC content.

B. Samples for Initial Selection: For each type of topcoat product.C. Samples for Verification: For each type of paint system and each color and gloss of topcoat.




1. Submit Samples on rigid backing, 8 inches square.2. Label each coat of each Sample.3. Label each Sample for location and application area.

D. Product List: For each product indicated, include the following:1. Cross-reference to paint system and locations of application areas. Use same

designations indicated on Drawings and in schedules.2. Indicate VOC content.

1.05 CLOSEOUT SUBMITTALSA. Coating Maintenance Manual: Provide coating maintenance manual including area summary

with finish schedule, area detail designating location where each product/color/finish was used,product data pages, material safety data sheets, care and cleaning instructions, touch-upprocedures, and color samples of each color and finish used.

1.06 MAINTENANCE MATERIAL SUBMITTALSA. Furnish extra materials that match products installed and that are packaged with protective

covering for storage and identified with labels describing contents.1. Paint: 1 gallon of each material and color applied.

1.07 QUALITY ASSURANCEA. Mockups: Apply mockups of each paint system indicated and each color and finish selected to

verify preliminary selections made under Sample submittals and to demonstrate aestheticeffects and set quality standards for materials and execution.1. Architect will select one surface to represent surfaces and conditions for application of

each paint system specified in Part 3.a. Vertical and Horizontal Surfaces: Provide samples of at least 100 sq. ft.b. Other Items: Architect will designate items or areas required.

2. Final approval of color selections will be based on mockups.a. If preliminary color selections are not approved, apply additional mockups of

additional colors selected by Architect at no added cost to Owner.3. Approval of mockups does not constitute approval of deviations from the Contract

Documents contained in mockups unless Architect specifically approves such deviations inwriting.

4. Subject to compliance with requirements, approved mockups may become part of thecompleted Work if undisturbed at time of Substantial Completion.

1.08 DELIVERY, STORAGE, AND HANDLINGA. Delivery and Handling: Deliver products to Project site in an undamaged condition in

manufacturer's original sealed containers, complete with labels and instructions for handling,storing, unpacking, protecting, and installing. Packaging shall bear the manufacture’s label withthe following information:1. Product name and type (description).2. Batch date.3. Color number.4. VOC content.5. Environmental handling requirements.6. Surface preparation requirements.7. Application instructions.

B. Store materials not in use in tightly covered containers in well-ventilated areas with ambienttemperatures continuously maintained at not less than 45 deg F.1. Maintain containers in clean condition, free of foreign materials and residue.2. Remove rags and waste from storage areas daily.




1.09 FIELD CONDITIONSA. Apply paints only when temperature of surfaces to be painted and ambient air temperatures are

between 50 and 95 deg F.B. Do not apply paints in snow, rain, fog, or mist; when relative humidity exceeds 85 percent; at

temperatures less than 5 deg F above the dew point; or to damp or wet surfaces.C. Hazardous Materials: It is not expected that hazardous materials will be encountered in the

Work.1. If suspected hazardous materials are encountered, do not disturb; immediately notify

Architect and Owner.PART 2 - PRODUCTS2.01 MANUFACTURERS

A. Basis-of-Design Manufacturer: Subject to compliance with requirements, provide1. Sherwin-Williams Company paints and coatings.

B. Comparable Manufacturers:1. Dunn-Edwards: 4885 E. 52nd Place, Los Angeles, CA 90058; (888) 337-24682. Behr Process Corporation: www.behr.com/#sle.3. Benjamin Moore & Co: www.benjaminmoore.com/#sle.4. PPG Paints: www.ppgpaints.com/#sle.

C. Comparable Products: Comparable products of approved manufacturers will be considered inaccordance with Section 016000 "Product Requirements," and the following:1. Products are approved by manufacturer in writing for application specified.2. Products meet performance and physical characteristics of basis of design product

including published ratio of solids by volume, plus or minus two percent.D. Source Limitations: Obtain paint materials from single source from single listed manufacturer.E. Manufacturer's designations listed on a separate color schedule are for color reference only and

do not indicate prior approval.2.02 PAINT - GENERAL

A. Material Compatibility:1. Provide materials for use within each paint system that are compatible with one another

and substrates indicated, under conditions of service and application as demonstrated bymanufacturer, based on testing and field experience.

2. For each coat in a paint system, provide products recommended in writing bymanufacturers of topcoat for use in paint system and on substrate indicated.

B. Provide all paint and coating products from the same manufacturer to the greatest extentpossible.1. In the event that a single manufacturer cannot provide all specified products, minor

exceptions will be permitted provided approval by Architect is obtained using the specifiedprocedures for substitutions.

C. VOC Content: For field applications, provide paints and coatings that complies with VOCcontent limits of authorities having jurisdiction.

D. Colors: Reference Spec Sec 090600-Schedule for Finishes2.03 SOURCE QUALITY CONTROL

A. Testing of Paint Materials: Owner reserves the right to invoke the following procedure:1. Owner will engage the services of a qualified testing agency to sample paint materials.

Contractor will be notified in advance and may be present when samples are taken. If paintmaterials have already been delivered to Project site, samples may be taken at Projectsite. Samples will be identified, sealed, and certified by testing agency.




2. Testing agency will perform tests for compliance with product requirements.3. Owner may direct Contractor to stop applying paints if test results show materials being

used do not comply with product requirements. Contractor shall remove noncomplyingpaint materials from Project site, pay for testing, and repaint surfaces painted with rejectedmaterials. Contractor will be required to remove rejected materials from previously paintedsurfaces if, on repainting with complying materials, the two paints are incompatible.

PART 3 - EXECUTION3.01 EXAMINATION

A. Examine substrates and conditions, with Applicator present, for compliance with requirementsfor maximum moisture content and other conditions affecting performance of the Work. Verifysuitability of substrates, including surface conditions and compatibility with existing finishes andprimers. Where acceptability of substrate conditions is in question, apply samples and performin-site testing to verify compatibility, adhesion, and film integrity of new paint application.1. Report, in writing, conditions that may affect application, appearance, or performance of

paint.B. Substrate Conditions:

1. Maximum Moisture Content of Substrates: When measured with an electronic moisturemeter as follows:a. Concrete: 12 percent.b. Fiber-Cement Board: 12 percent.c. Masonry (Clay and CMU): 12 percent.d. Wood: 15 percent.e. Portland Cement Plaster: 12 percent.f. Gypsum Board: 12 percent.

2. Portland Cement Plaster Substrates: Verify that plaster is fully cured.3. Exterior Gypsum Board Substrates: Verify that finishing compound is sanded smooth.

C. Proceed with coating application only after unsatisfactory conditions have been corrected;application of coating indicates acceptance of surfaces and conditions.

3.02 PREPARATIONA. Comply with manufacturer's written instructions and recommendations in "Data Pages"

applicable to substrates and paint systems indicated.B. Remove hardware, covers, plates, and similar items already in place that are removable and are

not to be painted. If removal is impractical or impossible because of size or weight of item,provide surface-applied protection before surface preparation and painting.1. After completing painting operations, use workers skilled in the trades involved to reinstall

items that were removed. Remove surface-applied protection.C. Clean substrates of substances that could impair bond of paints, including dust, dirt, oil, grease,

and incompatible paints and encapsulants.1. Remove incompatible primers and reprime substrate with compatible primers or apply tie

coat as required to produce paint systems indicated.D. Concrete Substrates: Remove release agents, curing compounds, efflorescence, and chalk. Do

not paint surfaces if moisture content or alkalinity of surfaces to be painted exceeds thatpermitted in manufacturer's written instructions.

E. Masonry Substrates: Remove efflorescence and chalk. Do not paint surfaces if moisture contentor alkalinity of surfaces or mortar joints exceeds that permitted in manufacturer's writteninstructions.

F. Steel Substrates: Remove rust, loose mill scale, and shop primer if any. Clean using methodsrecommended in writing by paint manufacturer.




G. Shop-Primed Steel Substrates: Clean field welds, bolted connections, and abraded areas ofshop paint, and paint exposed areas with the same material as used for shop priming to complywith SSPC-PA 1 for touching up shop-primed surfaces.

H. Galvanized-Metal Substrates: Remove grease and oil residue from galvanized sheet metal bymechanical methods to produce clean, lightly etched surfaces that promote adhesion ofsubsequently applied paints.

I. Aluminum Substrates: Remove loose surface oxidation.J. Wood Substrates:

1. Scrape and clean knots. Before applying primer, apply coat of knot sealer recommendedin writing by topcoat manufacturer for exterior use in paint system indicated.

2. Sand surfaces that will be exposed to view, and dust off.3. Prime edges, ends, faces, undersides, and backsides of wood.4. After priming, fill holes and imperfections in the finish surfaces with putty or plastic wood

filler. Sand smooth when dried.K. Plastic Trim Fabrication Substrates: Remove dust, dirt, and other foreign material that might

impair bond of paints to substrates.3.03 APPLICATION

A. Apply paints according to manufacturer's written instructions and recommendations in "MPIManual."1. Use applicators and techniques suited for paint and substrate indicated.2. Paint surfaces behind movable items same as similar exposed surfaces. Before final

installation, paint surfaces behind permanently fixed items with prime coat only.3. Paint both sides and edges of exterior doors and entire exposed surface of exterior door

frames.4. Paint entire exposed surface of window frames and sashes.5. Do not paint over labels of independent testing agencies or equipment name, identification,

performance rating, or nomenclature plates.6. Primers specified in painting schedules may be omitted on items that are factory primed or

factory finished if acceptable to topcoat manufacturers.B. Tint undercoats same color as topcoat, but tint each undercoat a lighter shade to facilitate

identification of each coat if multiple coats of same material are to be applied. Provide sufficientdifference in shade of undercoats to distinguish each separate coat.

C. If undercoats or other conditions show through topcoat, apply additional coats until cured filmhas a uniform paint finish, color, and appearance.

D. Apply paints to produce surface films without cloudiness, spotting, holidays, laps, brush marks,roller tracking, runs, sags, ropiness, or other surface imperfections. Cut in sharp lines and colorbreaks.

E. Painting Fire Suppression, Plumbing, HVAC, Electrical, Communication, and Electronic Safetyand Security Work:1. Paint the following work where exposed to view:

a. Equipment, including panelboards.b. Uninsulated metal piping.c. Uninsulated plastic piping.d. Pipe hangers and supports.e. Metal conduit.f. Plastic conduit.g. Tanks that do not have factory-applied final finishes.




3.04 FIELD QUALITY CONTROLA. Dry Film Thickness Testing: Owner may engage the services of a qualified testing and

inspecting agency to inspect and test paint for dry film thickness.1. Contractor shall touch up and restore painted surfaces damaged by testing.2. If test results show that dry film thickness of applied paint does not comply with paint

manufacturer's written recommendations, Contractor shall pay for testing and applyadditional coats as needed to provide dry film thickness that complies with paintmanufacturer's written recommendations.

3.05 CLEANING AND PROTECTIONA. At end of each workday, remove rubbish, empty cans, rags, and other discarded materials from

Project site.B. After completing paint application, clean spattered surfaces. Remove spattered paints by

washing, scraping, or other methods. Do not scratch or damage adjacent finished surfaces.C. Protect work of other trades against damage from paint application. Correct damage to work of

other trades by cleaning, repairing, replacing, and refinishing, as approved by Architect, andleave in an undamaged condition.

D. At completion of construction activities of other trades, touch up and restore damaged ordefaced painted surfaces.

3.06 EXTERIOR PAINTING SCHEDULEA. Concrete, Portland Cement Plaster (Stucco), Cementitious Siding, Nontraffic Surfaces:

1. Latex System: Select sheen.a. Prime Coat: Primer sealer, latex.

1) S-W Loxon Concrete & Masonry Primer Sealer, LX02W50, at 8.0 mils wet, 3.2mils dry.

b. Intermediate Coat: Latex, exterior, matching topcoat.c. Topcoat: Latex, exterior, flat.

1) S-W A-100 Exterior Latex Flat, A6 Series, at 4.0 mils wet, 1.2 mils dry, per coat.d. Topcoat: Latex, exterior, satin.

1) S-W A-100 Exterior Latex Satin, A82 Series, at 4.0 mils wet, 1.5 mils dry, percoat.

B. Concrete, Nontraffic Surfaces:1. Latex finish over latex texture System: Decorative Texture. Higher cost implications.

Medium Texture Standard.a. Prime Coat: Primer sealer, latex.


b. Topcoat: Latex, exterior, Fine, Med. Or Course.1) S-W ConFlex UltraCrete Acrylic Textured Coating, DF17 Series, at 50-80 square

feet, per coat.C. Concrete, Portland Cement Plaster (Stucco), Nontraffic Surfaces:

1. Elastomeric Coating System: Recommended for crack control and waterproofing. Highercost implications.a. Prime Coat: Primer sealer, latex.


2. Intermediate Coat: Latex, exterior, matching topcoat.3. Topcoat: Latex, exterior, satin.

a. S-W ConFlex Sherlastic Elastomeric Coating, CF16 Series, at 10.0-14.0 mils wet,4.0-6.0 mils dry, per coat.




D. Concrete: Pedestrian Traffic Surfaces:1. Latex Floor Paint System:

a. First Coat: Floor paint, latex, low gloss.1) S-W ArmorSeal Tread-Plex, B90 Series at 1.5-2.0 mils dry per coat.

b. Topcoat: Floor paint, latex, low gloss.1) S-W ArmorSeal Tread-Plex, B90 Series at 1.5-2.0 mils dry per coat.

2. Latex Textured Deck Coating System: Recommended Balconies, Walkways.a. First Coat: Deck Coating Acrylic Water-Based.

1) S-W Sher-Crete Flexible Concrete Waterproofer, A5 Series Textured at10.0-12.0 mils dry per coat.

b. Topcoat: Deck Coating Acrylic Water-Based.1) S-W Sher-Crete Flexible Concrete Waterproofer, A5 Series Textured at

10.0-12.0 mils dry per coat.E. Concrete Masonry Units (CMU): Select sheen.

1. Latex System:a. Block Filler: Block filler, latex, interior/exterior:

1) S-W PrepRite Block Filler, B25W25, at 75 to 125 sq. ft. per gal..b. Intermediate Coat: Latex, exterior, matching topcoat.c. Topcoat: Latex, exterior, flat.

1) S-W A-100 Exterior Latex Flat, A6 Series, at 4.0 mils wet, 1.2 mils dry, per coat.2. Topcoat: Latex, exterior, satin.

a. S-W A-100 Exterior Latex Satin, A82 Series, at 4.0 mils wet, 1.5 mils dry, per coat.F. Ferrous Metal Fabrications:

1. Waterbased Light Industrial Acrylic System: over shop coat primer. Standard system forHollow Metal Doors & Frames.a. Prime Coat: Primer, rust-inhibitive, water based:

1) S-W Pro Industrial Pro-Cryl Universal Primer, B66-310 Series, at 5.0 to 10 milswet, 2.0 to 4.0 mils dry.

b. Intermediate Coat: Water-based Acrylic, exterior, matching topcoat.c. Topcoat: Water-based Acrylic, semi-gloss, exterior:

1) S-W Pro Industrial Acrylic Semi-Gloss Coating, B66-650 Series, at 2.5 to 4.0mils dry, per coat.

2. Waterbased/Alkyd Urethane System: over shop coat primer. Hand Rails, Canopies. Exposed Structural Steel, Lintels, Pipe Ballards.a. Prime Coat: Primer, rust-inhibitive, water based:


b. Intermediate Coat: Water-based acrylic-alkyd, exterior, matching topcoat.c. Topcoat: Water-based alkyd-urethane, semi-gloss, exterior:

1) S-W Pro Industrial Waterbased Alkyd Urethane Semi-Gloss, B53-1150 Series,at 4.0 mils wet, 1.4 mils dry, per coat.

G. Galvanized and Zinc Rich Metal Fabrications:1. High Performance: Pigmented Epoxy/Polyurethane System: over Zinc Rich Primer Hand

Rails, Canopies. Exposed Structural Steel, Lintels, Pipe Ballards. Two part Urethane isthe Industry Standard for High Performance.a. Prime Coat: specified in division 05 12 00 Sectionb. Intermediate Coat: Epoxy, two-component, pigmented, matching topcoat.

1) S-W Macropoxy 646-100 Epoxy, B58-600 Series, at 5.0-10.0 mils dry.c. Topcoat: Polyurethane, two-component, pigmented, gloss:

1) S-W Hi-Solids Polyurethane 250, B65 Series, at 2.0 to 3.0 mils dry, per coat.




H. Wood Substrates: Including exposed wood items not indicated to receive shop-applied finish.1. Latex System: Select Sheen.

a. Prime Coat: Primer, latex for exterior wood.1) S-W Exterior Latex Primer, B42W8041, at 4.0 mils wet, 1.4 mils dry, per coat.

b. Intermediate Coat: Latex, exterior, matching topcoat.c. Topcoat: Latex, exterior, flat:

1) S-W A-100 Exterior Latex Flat, A6 Series, at 4.0 mils wet, 1.2 mils dry, per coat.d. Topcoat: Latex, exterior, satin:


I. Wood Substrates, Semi-Transparent Surfaces:1. Semi-Transparent Stain System:

a. First Coat: Semi-Transparent stain, latex, matching topcoat.b. Topcoat: Semi-Transparent stain, latex:

1) S-W WoodScapes® Semi-Transparent Stain, A15 Series.J. Exterior Gypsum Board Substrates:

1. Latex System: Select Sheena. Prime Coat: Primer bonding, water-based.

1) S-W PrepRite ProBlock Latex Primer/Sealer, B57-620 Series, at 4.0 mils wet,1.4 mils dry.

b. Intermediate Coat: Latex, exterior, matching topcoat.c. Topcoat: Latex, exterior, flat.

1) S-W A-100 Exterior Latex Flat, A6 Series, at 4.0 mils wet, 1.2 dry, per coat.d. Topcoat: Latex, exterior, satin:


K. Anti-Graffiti :1. Non-Sacrificial System:

a. Clear: Two-Part Urethane.1) S-W 2K Waterbased Urethane Anti-Graffiti Coating, B65-195/B65V195 Satin.

See Manufactures data page for details. (Application of a clear coating maychange the color appearance of the base coat. Apply a test patch prior tocoating the entire project)

END OF SECTION



10/9/2019 INTERIOR PAINTING09 9123-1

SECTION 09 9123INTERIOR PAINTING

PART 1 - GENERAL1.01 RELATED DOCUMENTS


1.02 SUMMARYA. Section includes surface preparation and the application of paint systems on the following

interior substrates:1. Concrete.2. Concrete masonry units (CMU).3. Steel.4. Galvanized metal.5. Aluminum (not anodized or otherwise coated).6. Wood.7. Tempered Hardboard.8. Gypsum board.

1.03 RELATED REQUIREMENTS:A. Section 01 6116 - Volatile Organic Compound (VOC) Content Restrictions.B. Section 05 5000 - Metal Fabrications: Shop-primed items.C. Section 05 5100 - Metal Stairs: Shop-primed items.D. Section 09 9600 - High-Performance Coatings.E. Section 21 0553 - Identification for Fire Suppression Piping and Equipment: Painted

identification.F. Section 21 0553 - Identification for Fire Suppression Piping and Equipment: Color coding

scheme for items to be painted under this section.G. Section 22 0553 - Identification for Plumbing Piping and Equipment: Painted identification.H. Section 22 0553 - Identification for Plumbing Piping and Equipment: Color coding scheme for

items to be painted under this section.I. Section 23 0553 - Identification for HVAC Piping and Equipment: Painted identification.J. Section 23 0553 - Identification for HVAC Piping and Equipment: Color coding scheme for

items to be painted under this section.K. Section 26 0553 - Identification for Electrical Systems: Painted identification.L. Section 26 0553 - Identification for Electrical Systems: Color coding scheme for items to be

painted under this section.M. Section 32 1723.13 - Painted Pavement Markings: Painted pavement markings.

1.04 ACTION SUBMITTALSA. Product Data: For each type of product. Include preparation requirements and application

instructions.1. Indicate VOC content.

B. Samples for Initial Selection: For each type of topcoat product.C. Samples for Verification: For each type of paint system and in each color and gloss of topcoat.

1. Submit Samples on rigid backing, 8 inches square.2. Label each coat of each Sample.3. Label each Sample for location and application area.




D. Product List: For each product indicated, include the following:1. Cross-reference to paint system and locations of application areas. Use same

designations indicated on Drawings and in schedules.2. Indicate VOC content.

1.05 CLOSEOUT SUBMITTALSA. Coating Maintenance Manual: Provide coating maintenance manual including area summary

with finish schedule, area detail designating location where each product/color/finish was used,product data pages, material safety data sheets, care and cleaning instructions, touch-upprocedures, and color samples of each color and finish used.

1.06 MAINTENANCE MATERIAL SUBMITTALSA. Furnish extra materials that match products installed and that are packaged with protective

covering for storage and identified with labels describing contents.1. Paint: 1 gallon of each material and color applied.

1.07 QUALITY ASSURANCEA. Mockups: Apply mockups of each paint system indicated and each color and finish selected to

verify preliminary selections made under Sample submittals and to demonstrate aestheticeffects and set quality standards for materials and execution.1. Architect will select one surface to represent surfaces and conditions for application of

each paint system specified in Part 3.a. Vertical and Horizontal Surfaces: Provide samples of at least 100 sq. ft.b. Other Items: Architect will designate items or areas required.

2. Final approval of color selections will be based on mockups.a. If preliminary color selections are not approved, apply additional mockups of

additional colors selected by Architect at no added cost to Owner.3. Approval of mockups does not constitute approval of deviations from the Contract

Documents contained in mockups unless Architect specifically approves such deviations inwriting.

4. Subject to compliance with requirements, approved mockups may become part of thecompleted Work if undisturbed at time of Substantial Completion.

1.08 DELIVERY, STORAGE, AND HANDLINGA. Delivery and Handling: Deliver products to Project site in an undamaged condition in

manufacturer's original sealed containers, complete with labels and instructions for handling,storing, unpacking, protecting, and installing. Packaging shall bear the manufacturer’s label withthe following information:1. Product name and type (description).2. Batch date.3. Color number.4. VOC content.5. Environmental handling requirements.6. Surface preparation requirements.7. Application instructions.

B. Store materials not in use in tightly covered containers in well-ventilated areas with ambienttemperatures continuously maintained at not less than 45 deg F.1. Maintain containers in clean condition, free of foreign materials and residue.2. Remove rags and waste from storage areas daily.

1.09 FIELD CONDITIONSA. Apply paints only when temperature of surfaces to be painted and ambient air temperatures are

between 50 and 95 deg F.




B. Do not apply paints when relative humidity exceeds 85 percent; at temperatures less than 5deg F above the dew point; or to damp or wet surfaces.

C. Lead Paint: It is not expected that lead paint will be encountered in the Work.1. If suspected lead paint is encountered, do not disturb; immediately notify Architect and

Owner.PART 2 - PRODUCTS2.01 MANUFACTURERS

A. Basis-of-Design Manufacturer: Subject to compliance with requirements, provide1. Sherwin-Williams Company paints and coatings.

B. Comparable Manufacturers:1. Dunn-Edwards: 4885 E. 52nd Place, Los Angeles, CA 90058; (888) 337-24682. Behr Process Corporation: www.behr.com/#sle.3. Benjamin Moore & Co: www.benjaminmoore.com/#sle.4. PPG Paints: www.ppgpaints.com/#sle.

C. Comparable Products: Comparable products of approved manufacturers will be considered inaccordance with Section 016000 "Product Requirements," and the following:1. Products are approved by manufacturer in writing for application specified.2. Products meet performance and physical characteristics of basis of design product

including published ratio of solids by volume, plus or minus two percent.D. Source Limitations: Obtain paint materials from single source from single listed manufacturer.

1. Manufacturer's designations listed on a separate color schedule are for color referenceonly and do not indicate prior approval.

2.02 PAINT, GENERALA. Material Compatibility:

1. Provide materials for use within each paint system that are compatible with one anotherand substrates indicated, under conditions of service and application as demonstrated bymanufacturer, based on testing and field experience.

2. For each coat in a paint system, provide products recommended in writing bymanufacturers of topcoat for use in paint system and on substrate indicated.

B. VOC Content: For field applications that are inside the weatherproofing system, paints andcoatings shall provide materials that comply with VOC limits of authorities having jurisdictionand for interior paints and coatings applied at Project site, the following VOC limits exclusive ofcolorants added to a tint base, when calculated according to 40 CFR 59, Subpart D (EPAMethod 24):1. Flat Paints and Coatings: 50 g/L.2. Nonflat Paints and Coatings: 150 g/L.3. Dry-Fog Coatings: 150 g/L.4. Primers, Sealers, and Undercoaters: 200 g/L.5. Anticorrosive and Antirust Paints Applied to Ferrous Metals: 250 g/L.6. Zinc-Rich Industrial maintenance Primers: 340 g/L.7. Pretreatment Wash Primers: 420 g/L.8. Floor Coatings: 100 g/L.

C. Colors: Reference Spec Sec 090600-Schedule for Finishes.2.03 SOURCE QUALITY CONTROL

A. Testing of Paint Materials: Owner reserves the right to invoke the following procedure:1. Owner will engage the services of a qualified testing agency to sample paint materials.

Contractor will be notified in advance and may be present when samples are taken. If paintmaterials have already been delivered to Project site, samples may be taken at Projectsite. Samples will be identified, sealed, and certified by testing agency.




2. Testing agency will perform tests for compliance with product requirements.3. Owner may direct Contractor to stop applying coatings if test results show materials being

used do not comply with product requirements. Contractor shall remove noncomplyingpaint materials from Project site, pay for testing, and repaint surfaces painted with rejectedmaterials. Contractor will be required to remove rejected materials from previously paintedsurfaces if, on repainting with complying materials, the two paints are incompatible.

PART 3 - EXECUTION3.01 EXAMINATION

A. Examine substrates and conditions, with Applicator present, for compliance with requirementsfor maximum moisture content and other conditions affecting performance of the Work. Verifysuitability of substrates, including surface conditions and compatibility with existing finishes andprimers. Where acceptability of substrate conditions is in question, apply samples and performin-situ testing to verify compatibility, adhesion, and film integrity of new paint application.1. Report, in writing, conditions that may affect application, appearance, or performance of

paint.B. Substrate Conditions:

1. Maximum Moisture Content of Substrates: When measured with an electronic moisturemeter as follows:a. Concrete: 12 percent.b. Masonry (Clay and CMU): 12 percent.c. Wood: 15 percent.d. Gypsum Board: 12 percent.e. Plaster: 12 percent.

2. Gypsum Board Substrates: Verify that finishing compound is sanded smooth.3. Plaster Substrates: Verify that plaster is fully cured.4. Spray-Textured Ceiling Substrates: Verify that surfaces are dry.

C. Proceed with coating application only after unsatisfactory conditions have been corrected;application of coating indicates acceptance of surfaces and conditions.

3.02 PREPARATIONA. Comply with manufacturer's written instructions and recommendations in "Data Pages"

applicable to substrates indicated.B. Remove hardware, covers, plates, and similar items already in place that are removable and are

not to be painted. If removal is impractical or impossible because of size or weight of item,provide surface-applied protection before surface preparation and painting.1. After completing painting operations, use workers skilled in the trades involved to reinstall

items that were removed. Remove surface-applied protection if any.C. Clean substrates of substances that could impair bond of paints, including dust, dirt, oil, grease,

and incompatible paints and encapsulants.1. Remove incompatible primers and reprime substrate with compatible primers or apply tie

coat as required to produce paint systems indicated.D. Concrete Substrates: Remove release agents, curing compounds, efflorescence, and chalk. Do

not paint surfaces if moisture content or alkalinity of surfaces to be painted exceeds thatpermitted in manufacturer's written instructions.1. Concrete Floors: Remove oil, dust, grease, dirt, and other foreign materials. Comply with

SSPC-SP-13/NACE 6 or ICRI 03732.E. Masonry Substrates: Remove efflorescence and chalk. Do not paint surfaces if moisture content

or alkalinity of surfaces or mortar joints exceed that permitted in manufacturer's writteninstructions.




F. Steel Substrates: Remove rust, loose mill scale, and shop primer, if any. Clean using methodsrecommended in writing by paint manufacturer.

G. Shop-Primed Steel Substrates: Clean field welds, bolted connections, and abraded areas ofshop paint, and paint exposed areas with the same material as used for shop priming to complywith SSPC-PA 1 for touching up shop-primed surfaces.

H. Galvanized-Metal Substrates: Remove grease and oil residue from galvanized sheet metalfabricated from coil stock by mechanical methods to produce clean, lightly etched surfaces thatpromote adhesion of subsequently applied paints.

I. Aluminum Substrates: Remove loose surface oxidation.J. Wood Substrates:

1. Scrape and clean knots and apply coat of knot sealer before applying primer.2. Sand surfaces that will be exposed to view and dust off.3. Prime edges, ends, faces, undersides, and backsides of wood.4. After priming, fill holes and imperfections in the finish surfaces with putty or plastic wood

filler. Sand smooth when dried.K. Cotton or Canvas Insulation Covering Substrates: Remove dust, dirt, and other foreign material

that might impair bond of paints to substrates.3.03 APPLICATION

A. Apply paints according to manufacturer's written instructions and to recommendations in "MPIManual."1. Use applicators and techniques suited for paint and substrate indicated.2. Paint surfaces behind movable equipment and furniture same as similar exposed

surfaces. Before final installation, paint surfaces behind permanently fixed equipment orfurniture with prime coat only.

3. Paint front and backsides of access panels, removable or hinged covers, and similarhinged items to match exposed surfaces.

4. Do not paint over labels of independent testing agencies or equipment name, identification,performance rating, or nomenclature plates.

5. Primers specified in painting schedules may be omitted on items that are factory primed orfactory finished if acceptable to topcoat manufacturers.

B. Tint each undercoat a lighter shade to facilitate identification of each coat if multiple coats ofsame material are to be applied. Tint undercoats to match color of topcoat but provide sufficientdifference in shade of undercoats to distinguish each separate coat.

C. If undercoats or other conditions show through topcoat, apply additional coats until cured filmhas a uniform paint finish, color, and appearance.

D. Apply paints to produce surface films without cloudiness, spotting, holidays, laps, brush marks,roller tracking, runs, sags, ropiness, or other surface imperfections. Cut in sharp lines and colorbreaks.

E. Painting Fire Suppression, Plumbing, HVAC, Electrical, Communication, and Electronic Safetyand Security Work:1. Paint the following work where exposed in equipment rooms:

a. Equipment, including panelboards.b. Uninsulated metal piping.c. Uninsulated plastic piping.d. Pipe hangers and supports.e. Metal conduit.f. Plastic conduit.g. Tanks that do not have factory-applied final finishes.




h. Duct, equipment, and pipe insulation having cotton or canvas insulation covering orother paintable jacket material.

2. Paint the following work where exposed in occupied spaces:a. Equipment, including panelboards.b. Uninsulated metal piping.c. Uninsulated plastic piping.d. Pipe hangers and supports.e. Metal conduit.f. Plastic conduit.g. Duct, equipment, and pipe insulation having cotton or canvas insulation covering or

other paintable jacket material.h. Other items as directed by Architect.

3. Paint portions of internal surfaces of metal ducts, without liner, behind air inlets and outletsthat are visible from occupied spaces.

3.04 FIELD QUALITY CONTROLA. Dry Film Thickness Testing: Owner may engage the services of a qualified testing and

inspecting agency to inspect and test paint for dry film thickness.1. Contractor shall touch up and restore painted surfaces damaged by testing.2. If test results show that dry film thickness of applied paint does not comply with paint

manufacturer's written recommendations, Contractor shall pay for testing and applyadditional coats as needed to provide dry film thickness that complies with paintmanufacturer's written recommendations.

3.05 CLEANING AND PROTECTIONA. At end of each workday, remove rubbish, empty cans, rags, and other discarded materials from

Project site.B. After completing paint application, clean spattered surfaces. Remove spattered paints by

washing, scraping, or other methods. Do not scratch or damage adjacent finished surfaces.C. Protect work of other trades against damage from paint application. Correct damage to work of

other trades by cleaning, repairing, replacing, and refinishing, as approved by Architect, andleave in an undamaged condition.

D. At completion of construction activities of other trades, touch up and restore damaged ordefaced painted surfaces.

3.06 INTERIOR PAINTING SCHEDULEA. Concrete Substrates, Nontraffic Surfaces:

1. Institutional low odor / low VOC System:a. Prime Coat: Primer, latex, interior. Select Sheen Eggshell standard


b. Intermediate Coat: Latex, interior, matching topcoat.c. Topcoat: Latex, interior, eggshell.

1) S-W ProMar 200 Zero VOC Latex Eg-Shel, B20-12600 Series, at 4.0 mils wet,1.7 mils dry, per coat.

d. Topcoat: Latex, interior, semi-gloss.1) S-W ProMar 200 Zero VOC Latex Semi-Gloss, B31-2600 Series, at 4.0 mils wet,

1.6 mils dry, per coat.2. Water-Based Light Industrial Coating System: For added durability and burnish protection

at hallways, stairwells, toilets, kitchens, gym walls, ultradeep accent colors.a. Prime Coat: Primer sealer, latex, interior:





b. Intermediate Coat: Light industrial coating, interior, water based, matching topcoat.c. Topcoat: Light industrial coating, interior, water based, eggshell:

1) S-W Pro Industrial Pre-Catalyzed Water Based Epoxy, K45-1151 Series, at 4.0mils wet, 1.5 mils dry, per coat.

d. Topcoat: Light industrial coating, interior, water based, semi-gloss:1) S-W Pro Industrial Pre-Catalyzed Water Based Epoxy, K46-1151 Series, at 4.0

mils wet, 1.5 mils dry, per coat.B. Concrete Substrates, Pedestrian Traffic Surfaces:

1. Epoxy System: Clear or Pigmented Thin Film Moderate Dutya. Prime Coat: Epoxy, matching topcoat.b. Topcoat: Epoxy, Gloss:

1) S-W Armorseal 8100 Water Based Epoxy Floor Coating, B70 Series, at 2.0 to4.0 mils dry, per coat.

C. CMU Substrates:1. Institutional low odor / low VOC System: Select Sheen Eggshell standard

a. Block Filler: Block filler, latex, interior/exterior:1) S-W PrepRite Block Filler, B25W25, at 75-125 sq. ft. per gal.

b. Intermediate Coat: Latex, interior, matching topcoat.c. Topcoat: Latex, interior, eggshell:

1) S-W ProMar 200 Zero VOC Latex Eg-Shel, B20-12600 Series, at 4.0 mils wet,1.7 mils dry, per coat.

d. Topcoat: Latex, interior, semi-gloss:1) S-W ProMar 200 Zero VOC Latex Semi-Gloss, B31-2600 Series, at 4.0 mils wet,

1.6 mils dry, per coat.2. Water-Based Light Industrial Coating System: Consider for added durability and burnish

protection, hallways, stairwells, toilets, kitchens, gym walls, ultradeep accent colors.a. Block Filler: Block filler, latex, interior/exterior:

1) S-W PrepRite Block Filler, B25W25, at 75-125 sq. ft. per gal.b. Intermediate Coat: Light industrial coating, interior, water based, matching topcoat.c. Topcoat: Light industrial coating, interior, water based, eggshell:


d. Topcoat: Light industrial coating, interior, water based, semi-gloss:1) S-W Pro Industrial Pre-Catalyzed Water Based Epoxy, K46-151 Series, at 4.0

mils wet, 1.5 mils dry, per coat.D. Metal Substrates (Aluminum, Steel, Galvanized Steel):

1. Water based Acrylic System: Standard system for doors & frames, misc. metals.a. Prime Coat: Primer, rust-inhibitive, water based:


b. Intermediate Coat: Water-based Acrylic, interior, matching topcoat.c. Topcoat: Water-based Acrylic, semi-gloss, interior:


2. Water-Based Light Industrial Coating System: Suggested for handrails, stair stringers.a. Prime Coat: Primer, rust-inhibitive, water based:


b. Intermediate Coat: Light industrial coating, interior, water based, matching topcoat.c. Topcoat: Light industrial coating, interior, water based, semi-gloss:





3. Water-Based Dry-Fall System: Exposed Ceilings Select Sheen Flat standarda. Top Coat: Dry-fall latex, flat:

1) S-W Pro Industrial Waterborne Acrylic Dryfall Flat, B42-181 Series, at 6.0 milswet, 1.5 mils dry.

b. Top Coat: Dry-fall latex, eggshell:1) S-W Pro Industrial Waterborne Acrylic DryFall Eg-Shel, B42-82, at 6.0 mils wet,

1.9 mils dry.E. Wood Substrates: Including exposed wood items not indicated to receive shop-applied finish.

1. Waterbased/Acrylic System:a. Prime Coat: Primer sealer, latex, interior:

1) S-W Premium Wall & Wood Primer, B28W8111, at 4.0 mils wet, 1.8 mils dry.b. Intermediate Coat: Water-based Acrylic, interior, matching topcoat.c. Topcoat: Water-based Acrylic, semi-gloss, interior:


F. Wood Substrates: Stain and Waterbased Urethane finish.1. Transparent System: Low VOC Finish

a. Stain Coat: interior: S-W Minwax Performance Series Tintable Wood Stain 250 VOC.b. Intermediate Coat: WB Polyurethane, matching topcoat.c. Topcoat: Clear, interior, satin, Gloss Level 3:

1) S-W Minwax Waterbased Oil-Modified Polyurethane, Satin.G. Gypsum Board Substrates:

1. Latex System: Select Sheen Eggshell standarda. Prime Coat: Primer, latex, interior:

1) S-W ProMar 200 Zero VOC Latex Primer, B28W2600, at 4.0 mils wet, 1.0 milsdry.

b. Intermediate Coat: Latex, interior, matching topcoat.c. Topcoat: Latex, interior, flat:

1) S-W ProMar 200 Zero VOC Latex Flat, B30-12600 Series, at 4.0 mils wet, 1.6mils dry, per coat.

d. Topcoat: Latex, interior, eggshell:1) S-W ProMar 200 Zero VOC Latex Eg-Shel, B20-12600 Series, at 4.0 mils wet,

1.7 mils) dry, per coat.e. Topcoat: Latex, interior, semi-gloss:

1) S-W ProMar 200 Zero VOC Latex Semi-Gloss, B31-2600 Series, at 4.0 mils wet,1.6 mils dry, per coat.

2. Water-Based Light Industrial Coating System: Consider for added durability and burnishprotection, hallways, stairwells, toilets, kitchens, gym walls, ultradeep accent colors.a. Prime Coat: Primer sealer, latex, interior:

1) S-W ProMar 200 Zero VOC Latex Primer, B28W2600, at 4.0 wet, 1.0 mils dry.b. Intermediate Coat: Light industrial coating, interior, water based, matching topcoat.c. Topcoat: Light industrial coating, interior, water based, eggshell:

1) S-W Pro Industrial Pre-Catalyzed Waterbased Epoxy, K45-151 Series, at 4.0mils wet, 1.5 mils dry, per coat.

d. Topcoat: Light industrial coating, interior, water based, semi-gloss:1) S-W Pro Industrial Pre-Catalyzed Waterbased Epoxy, K46-151 Series, at 4.0

mils wet, 1.5 mils dry, per coat.3. Epoxy-Modified Latex System: Select sheen, gloss is standard. For wet areas, chemical

resistance, surgery rooms, labs.a. Prime Coat: Primer sealer, latex, interior:

1) S-W ProMar 200 Zero VOC Interior Latex Primer, B28W2600, at 1.0 mils dry,per coat.




b. Intermediate Coat: Epoxy-modified latex, interior, matching topcoat.c. Topcoat: Epoxy-modified latex, interior, eggshell:

1) S-W Pro Industrial Waterbased Catalyzed Epoxy Eggshell, B73-360 Series, at2.0 to 4.0 mils dry, per coat.

d. Topcoat: Epoxy-modified latex, interior, gloss:1) S-W Pro Industrial Waterbased Catalyzed Epoxy Gloss, B73-300 Series, at 2.0

to 4.0 mils dry, per coat.e. See High Performance 099600 for Immersion Grade or severe moisture

END OF SECTION



10/9/2019 PROJECTION SCREENS11 5213-1

SECTION 11 5213PROJECTION SCREENS

PART - 1 GENERAL1.01 RELATED DOCUMENTS


1.02 SUMMARYA. Drawings and general provisions of the Contract, including General and Supplementary

Conditions and Division 1 Specification Sections, apply to this Section.B. Section Includes:

1. Manual retractable front-projection screens2. Motorized retractable front-projection screens3. Fixed front projection screens4. Cable, wiring, connection devices for wiring systems to be used as signal pathways for

projection systems1.03 RELATED SECTIONS:

A. Division 26: Section “Raceways and boxes for Audio-Video Systems”B. Division 27: Section “Audio-Video Equipment”

1.04 MEASUREMENT PROCEDURES:A. Product quantity is as required.B. Portable equipment is specified with specific quantities listed in the specification.C. Some equipment is shown on the drawing and required as part of the portable equipment

package. The total quantity requirement is the sum of the equipment show on the drawings andthe specific quantity listed in the specification.

D. Some product listed under this section may not be required to fulfill the obligations of the Work.1.05 DEFINITIONS

A. For purposes of the Contract Documents, these words and phrases are defined as follows:1. Fully Operational: A system that meets or exceeds aal of the requirements set forth in the

Contract Documents and is ready for the Final Observation Inspection.2. Fabricator's Shop: The address listed on the business license of the entity responsible for

fabricating the work sepcified in this Section.3. Provide: Furnish, Install, Program, Document, Test and Demonstrate.4. AV: Audio-Video, Audiovisual.5. EAV: Audiovisual Infrastructure Category Drawings6. AVS: Audiovisual SystemCategory Drawings7. Gain of Front-Projection Screens: Ratio of light reflected from screen material to that

reflected perpendicularly from a magnesium carbonate surface as determined per SMPTERP 94.

8. Half Gain Angle: The angle, measured from the axis of the screen surface to the mostcental position on a perpendicular plane through the horizontal centerline of the screenwhere gain is half of the peak gain.

9. ANSI: American National Standards Institute10. ASA: Acoustical Society of America11. ASTM: ASTM International12. ICIA: International Communications Industries Association13. NAB: National Association of Broadcasters14. NEC: National Elecrical Code




15. NFPA: National Fire Protection Association16. SMPTE: Society of Motion Picture and Television Engineers17. EMI: Electromagnetic Interference18. UL: Underwriters Laboratories19. CE: Conformte Eurpeenne

1.06 SUBMITTALSA. Submit the following items in accordance with the General Conditions and Division 1.B. Only complete submittals will be reviewed; incomplete submittals will be rejected.C. Electronic Media:

1. In addition to the requirements in Division 1, submit all material on three solid state USBdrives.a. Adobe Acrobat .pdf and Autocad .DWG files of the Record Drawings.b. Adobe Acrobat .pdf files of the Manufacturers Equipment Specification Sheets.c. Adobe Acrobat .pdf files of the System Operating Instructions.d. Adobe Acrobat .pdf files of the Performance Tests.

D. Installer Qualifications:1. Provide the installer qualification information described in Part 1 Quality Assurance.

E. Product Data:1. Bill of Quantity: Provide a Bill of Quantity for each item specified in Part 2 and all incidental

material supplied necessary to complete the Work as specified herein and shown on theDrawings.

2. Provide the following information for each item listed:a. Manufacturer's name.b. Manufacturer’s model number.c. Product description.d. Quantity supplied.

F. Manufacturers Equipment Specification Sheets:1. For each item specified in Part 2 submit a Manufacturer’s Equipment Specification Sheet

listing the product features, specification and physical characteristics. If more than oneproduct or model option is listed, identify clearly on the sheet which product is beingsubmitted.

2. Tabulate each the Specification Sheets using tab dividers in the same order as each itemappears in Part 2 of this Section.

G. Shop Drawings:1. General:

a. Shop Drawings shall be clear and legible.b. Character height shall be 1/8-inch high when plotted at full scale.c. Draw all Shop Drawings using the most current version of AutoCAD by Autodesk.d. Title character height shall be 1/4-inch when plotted at full scale.

1) Drawings shall be 1/4-inch, 3/4-inch, 1-inch, 1-1/2-inch, 3-inch and 1-inch =1-inch scale.

2. Plan View Drawings:a. General:

1) Coordinate the Plan View Drawings with the Single Line Diagrams.b. Clearly show and dimension the location and size of all devices.c. Include the following for each cable in a Cable Schedule:

1) Manufacturer name.2) Manufacturer's model number.3) Designation prefix.4) Cable type.




5) Cable color.d. Detail the conduit fill. For each conduit run show the cable fill, include:

1) Cable designation.2) Cable quantity.

3. Contractor Fabricated Equipment Drawings: For each contractor fabricated indicate:a. All components and equipment, including:

1) Manufacturer's name.2) Manufacturers model number.3) Dimensions.4) Component values.5) Locations.

4. Structural Drawings:a. Locations, loads and attachment to structure shall be per DSA Approved plans.b. This system is not a DSA deferred Approval submittal.c. For all equipment attached to the building indicate:

1) All loads.2) Location of attachment to building structure.3) Dimensions.4) Method of connection to building structure.5) Details of hardware.6) Manufacturer's name.7) Manufacturer’s model number.8) Design calculations.

5. Samples:a. Submit a sample for each piece of equipment visible in a public area.

H. Substantial Completion Inspection Request:1. Submit a Substantial Completion Inspection request letter certifying that all of the criteria

defined in the Contract Documents has been satisfied and the system is Fully Operational.The Request must be written on company letterhead and signed by the Owner, Presidentor Majority Shareholder of the Contractor responsible for the Work.

I. Operations and Service Manual:1. General:

a. Compose the Manual using a single, consistent visual format and writing style.b. Portions of the Manual may be derived from the equipment manufacturer's instruction

manuals and may include reproductions of artwork and other materials.c. Manual Organization:

1) Organize the Manual in a three ring binder.2) Print the Manual using 24lb. bond paper.3) Separate each Part with labeled tab dividers.4) Tabulate each the Equipment Manual using tab dividers in the same order as

each item appears in Part 2 of this Section.2. Part I - Index, include:

a. Title page:1) Project name.2) Date.3) Specification reference number.4) Installers name and address.5) Installers service phone number.

3. Part III - System Operating Instructions:a. Provide an overview of the System Description that describes the functionality of the

system.




b. Provide comprehensive instructions for the operations of all the systems specified inthis Section.

c. Provide comprehensive system operation instructions, include:1) Custom equipment programming instructions.

4. Part IV - Equipment Information:a. For each piece of equipment specified in this Section, include:

1) Manufacturer's installation, operating and service manual.5. Part V - Performance Tests:

a. Provide comprehensive documentation of all performance verification tests andprocedures described in Part 2 and Part 3 of this Section.

J. Record Drawings:1. General:

a. Develop the Record Drawings from the final As-Built condition of the system.b. Include the corrections from the Shop Drawing Submittal.c. Include all Changes as a result of Change Orders.

2. Mount one full-scale original of the As-Built Drawings plotted on 20 lb. bond paper behindacrylic in the control room for each system.

K. Training Materials Submittal:1. Provide all training materials for review prior to scheduling training sessions.2. Warranties: Special Warranty specified in this Section.

1.07 QUALITY ASSURANCEA. Regulatory Requirements:

1. Comply with the latest version of the ANSI, Cal-OSHA, IEC, IEEE, FCC, NEC and NFPArequirements.

2. Listed and labeled as defined in California Electrical Code by a testing agency acceptableto authorities having jurisdiction, and marked for intended use.

3. Equipment and materials shall be UL listed.B. Installer Qualifications:

1. The installer shall have the following experience, certifications and requirements:a. Authorized representative of equipment manufacturer for both installation and

maintenance of equipment required for this Section.b. Successfully completed a minimum of three projects of similar scope and size.

Provide letters of recommendation from the Owner’s Representative from those threeprojects.

c. Installation staff: ICIA CTS-I certification. Provide certification from ICIA.d. Engineering staff: ICIC CTS-D certification. Provide certification from ICIA.e. Support staff: ICIA CTS certification. Provide certification from ICIA.

2. Submit the following information in accordance with the Instruction to Bidders:a. A detailed brochure describing its capabilities.b. Examples of three similar installations within the past two five years.c. Distribution arrangements with manufacturers.

1) Franchises.2) Dealerships.3) Distributorships.

d. Evidence of all necessary licenses and certificates to perform the specified work.e. Financial capability.f. Bonding capability.g. Identify all sources of labor.h. Identify all local agents.i. Identify all subcontractors.




j. Personnel experience background for the following people who will be directlyresponsible for the Work specified herein:1) Director of engineering.2) Project engineer.3) Project manager.4) Shop personnel.5) Field personnel.

3. This submittal must justify in the judgment of the Owner’s Representative that theContractor has the capability to manage and install a project of this size and scope andthat he is capable of the necessary business and technical arrangements for thisinstallation and the pursuant warranty service.

C. Manufacturer Qualifications:1. A prime system manufacturer who maintains or sponsors a service center capable of

providing training, parts, and emergency maintenance and repairs at Project site with a24-hour maximum response time.

2. Minimum of 10 years continuous experience in the design and manufacture of audio-video,control, network and optical equipment.

3. ISO 9001 quality certification for a period of 5-years or longer.D. Substitutions:

1. Model numbers and manufacturers included in this Section are listed as a standard offunction, performance and quality.

2. Prior to acceptance of a substitute product, demonstrate equivalency by direct A/Bcomparison to the Owners Representative.

E. Source Limitations:1. Obtain each category of audio-video systems through one source from a single

manufacturer. Obtain each piece of equipment as a complete unit, including necessarymounting hardware and accessories.

F. Materials:1. Provide only new materials and products.2. Do not use discontinued items replaced by newer models or versions.3. If an item specified in Part 2 of this section has been discontinued, submit the

manufacturer’s direct replacement for review and approval by the Owner’s representative.G. Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70,

Article 100, by a testing agency acceptable to authorities having jurisdiction, and marked forintended use.

1.08 DELIVERY, STORAGE AND HANDLINGA. Deliver portable audio and visual system components, equipment, materials, and accessories to

project site in original, unopened packages and store them in a fully enclosed, conditionedspace where they will be protected against damage from moisture, humidity, temperatureextremes, direct sunlight, surface contamination, and other causes.

B. Handle components, equipment, materials and accessories carefully to avoid damaging units inany way.

C. Do not deliver the audio-video system assemblies until the building is enclosed and otherconstruction within spaces where the audio-video system assemblies will be installed iscomplete and ready for installation.

1.09 COORDINATIONA. Coordinate arrangement of the audio-video system assemblies with adjacent construction, and

with components occupying ceiling space, including structural members, pipes, air-distributioncomponents, raceways, cable trays, recessed lighting fixtures, ceiling framing, light fixtures,HVAC equipment, fire-suppression system, and partitions.




B. Refer to Electrical Drawings for service voltage, power feed. Refer to Category AVS Drawingsfor control and interlock wiring for equipment specified under this Section.

C. Coordinate layout and installation of audio-video system with adjacent construction, includingceiling framing, light fixtures, HVAC equipment, fire-suppression system, and partitions.

1.10 PROJECT SITE CONDITIONSA. Environment Requirements.

1. The spaces where audio-video system assemblies are installed shall meet the followingrequirements:a. Free from dust generated from construction.b. The room temperature shall be within the specified operating temperature

recommended by manufacturer.1.11 SEQUENCING

A. General:1. Allow adequate time for corrections to be made after Inspections to maintain the Project

Schedule.2. Allow adequate time for corrections to be made after Submittals to maintain the Project

Schedule.B. Sequence the Project Submittals and Inspection Requests as follows:

1. Qualifications Submittal.2. Shop Drawings and Product Data3. Shop Test Report4. Shop Observation Inspection Request.5. Shop Observation Inspection.6. Substantial Completion Inspection Request.7. Substantial Completion Inspection.8. Field Test Report9. Operations and Service Manual and Record Drawing10. Final Inspection Request11. Final Inspection.12. Training Request.13. Training.14. Warranties

1.12 WARRANTYA. General Warranty: Special warranty specified in this Article shall not deprive Owner of other

rights that the Owner may have under other provisions of the Contract Documents and shall bein addition to, and run concurrent with, other warranties made by Contractor under requirementsof the Contract Documents.

B. Special Warranty: Written warranty, executed by manufacturer agreeing to repair or replacecomponents of audio-video system that fail in materials or workmanship within specifiedwarranty period.1. Warranty Period: Two years from date of the Final Inspection and Acceptance.

C. The Warranty Period will begin when all of the documented Substantial Completion InspectionDeficiencies have been corrected to the satisfaction of the Owner and the Owner’sRepresentative.

1.13 MAINTENANCEA. Maintenance Service:

1. Provide one service call to the project site to check and adjust the AV systems threemonths after Final Acceptance.




2. Provide one service call to the project site to check and adjust the AV systems six monthsafter Final Acceptance.

3. Maintain and monitor the all controllable devices remotely.4. Provide a Maintenance Service Agreement Contract to maintain the AV system after the

Warranty Period has expired as part of the Bid Documents. The Service Agreement scopeof work includes maintenance required to the AV system so that it functions exactly as itdid at the time of final acceptance.

PART - 2 PRODUCTS2.01 FLUSH MOUNT MOTORIZED PROJECTION SCREEN (SC-ST-BB226D)

A. Manufacturer: Stewart Filmscreen Corporation BB226.41D -(GM70) with optional low voltagecontrol or equal (no known equal).

B. Features:1. Tab-Guy tensioning system.2. Motorized Roller System may be activated by infrared/remote control, switch or projector

screen trigger.3. Self-finishing trim-ring.4. Drywall and plaster flange.5. Aluminum construction.6. Screen can be wall mounted or ceiling recessed.7. Compact in tube motor.8. UL approved.9. Low voltage control.

C. Specification:1. Image Size: 226.41” Diagonal.2. Image Height: 10’3. Image Width: 16'4. Aspect Ratio: 16:105. Top Masking: 12" or as shown on Drawings6. Color: Color match the wall-ceiling surface and provide the paint to the manufacturer for

painting.2.02 FRONT PROJECTION SCREEN PROJECTION MATERIAL AND VIEWING SURFACE:

A. Low Gain - Wide Angle - Ambient Light Rejection Viewing Surface (GM 70):1. Manufacturer: Stewart Filmscreen Corporation Greymatte 70 or equal (no known equal).2. Features:

a. High ambient light tolerance.b. Increases contrast ratio.c. Washable, flame retardant material.

3. Specification:a. Peak gain: 0.70.b. Half Gain: N/A.c. Viewing Angle: 180 Degrees.

B. Unity Gain - Medium Angle - Ambient Light Rejection Viewing Surface (FH 4G):1. Manufacturer: Stewart Filmscreen Corporation Firehawk G4 or equal (no known equal).2. Features:

a. Optimized for 1080P.b. Ambient light tolerance.c. Increases contrast ratio.d. Washable, flame retardant material.

3. Specification:a. Gain: 1.




b. Half Gain: 35 Degrees.c. Viewing Angle: 160 Degrees.

C. Low Gain - Medium Angle - Ambient Light Rejection Matte Viewing Surface (GH RS 3G):1. Manufacturer: Stewart Filmscreen Corporation GrayHawk RS 3G or equal (no known

equal).2. Features:

a. High ambient light tolerance.b. Increases contrast ratio.c. Washable, flame retardant material.

3. Specification:a. Peak gain: 0.95.b. Half Gain: 64 Degrees.c. Viewing Angle: 160 Degrees.

D. Unity Gain - Wide Angle - Viewing Surface (SM):1. Manufacturer: Stewart Filmscreen Corporation Snowmatte or equal (no known equal).2. Features:

a. Wide viewing cone.b. Washable, flame retardant material.

3. Specification:a. Gain: 1.b. Half Gain: NA.c. Viewing Angle: 180 Degrees.

E. Medium Gain - Medium Angle Viewing Surface Viewing Surface:1. Manufacturer: Stewart Filmscreen Corporation StudioTek 130 G3 or equal (no known

equal).2. Features:

a. 30% brighter than standard matte white material.b. Washable, flame retardant material.

3. Specification:a. Peak gain: 1.3.b. Half Gain: 68 Degrees.c. Viewing Angle: 160 Degrees.

F. High Gain - Wide-Angle Viewing Surface (WA):1. Manufacturer: Stewart Filmscreen Corporation Ultramatte 150 or equal (no known equal).2. Features:

a. 50% brighter than standard matte white material.b. Washable, flame retardant material.

3. Specification:a. Peak gain: 1.5.b. Half Gain: .75.c. Viewing Angle: 140 Degrees.

G. High Gain - Narrow Angle Viewing Surface (MP):1. Manufacturer: Stewart Filmscreen Corporation Videomatte 200 or equal (no known equal).2. Features:

a. 100% brighter than standard matte white material.b. Color corrected for CRT projector.c. Washable, flame retardant material.

3. Specification:a. Peak gain: 2.b. Half Gain: 1.c. Viewing Angle: 120 Degrees.




H. High-Gain Speciality Viewing Surface (HG):1. Manufacturer: Stewart Filmscreen Corporation Silver 3D or equal (no known equal).2. Features:

a. Enhances 3D effects.b. Silver based material.c. High contrast ratio.d. Non-Washable, flame retardant material

3. Specification:a. Peak gain: 3.2.b. Half Gain: 1.6.c. Viewing Angle: 44 Degrees.

2.03 INSTALLED CABLEA. DC Control:

1. Acceptable: Belden 8461 or equal (no known equal).2. Features:

a. CM rated.b. High conductivity.c. PVC jacket.

3. Specification:a. Conductor Configuration: 2 unshielded twisted pair.b. Wire Gauge: 18.c. Shield Coverage: 0%.d. Conductor: Stranded 7x26.e. Nominal Outside Diameter: .234-inch.

2.04 DC POWER:A. Acceptable: Belden 8477 or equal (no known equal).

1. Features:a. CM rated.b. High conductivity.c. PVC jacket.

2. Specification:a. Conductor Configuration: 2 unshielded twisted pair.b. Wire Gauge: 12.c. Shield Coverage: 0%.d. Conductor: Stranded 65x30.e. Nominal Outside Diameter: .386-inch.

2.05 PORTABLE CABLEA. DC Power:

1. Acceptable: Belden 19228 or equal (no known equal).2. Features:

a. SO-2.b. Neoprene jacket.

3. Specification:a. Conductor Configuration: Twisted pair.b. Wire Gauge: 16.c. Shield Coverage: Un-shielded.d. Conductor: Stranded copper (26x30).e. Nominal Outside Diameter: .315-inch.




2.06 CABLE LABELSA. Installed and Portable Cable

1. Acceptable:a. <0.313-inch cable diameter: Thomas and Betts WES2112 or equal (no known equal).b. <0.468-inch cable diameter: Thomas and Betts WES12214 or equal (no known

equal).2. Features

a. Printable markers.b. WSL self-laminating vinyl.c. Maximum protection against most common elements.

3. Specification:a. Thickness: 1 mil.b. Color: White

4. Quantity: Two for each cable supplied minimum.2.07 ACCESSORIES

A. 12V. Power Supply1. Features:

a. Linear DC power design.b. UL Listed

2. Specification:a. Voltage: 12V.b. Power Redundancy: 100% extra.

3. Acceptable: Condor Linear series power supply or equal (no known equal).B. 24V. Power Supply

1. Features:a. Linear DC power design.b. UL Listed

2. Specification:a. Voltage: 24V.b. Power Redundancy: 100% extra.

3. Acceptable: Condor Linear series power supply or equal (no known equal).2.08 FINISHES

A. Manufacturer’s logos:1. Remove all manufacturers’ names, logos, or other symbols from speakers or other objects

placed in view of the public.PART - 3 EXECUTION3.01 EXAMINATION

A. Examine roughing-in for the audio-video systems to verify actual locations of cable connectionsbefore audio- video systems installation.

B. Examine pathway elements intended for cables. Check raceways, cable trays, and otherelements for compliance with space allocations, installation tolerances, hazards to cableinstallation, and other conditions affecting installation.

C. Examine walls, floors, roofs, equipment bases, and roof supports for suitable conditions whereaudio-video systems are to be installed.

D. Proceed with installation only after unsatisfactory conditions have been corrected.3.02 INSTALLATION

A. General:




1. Install projection screens at locations indicated to comply with screen manufacturer'swritten instructions.

2. Install front-projection screens with screen cases in position and in relation to adjoiningconstruction indicated. Securely anchor to supporting substrate in a manner that producesa smoothly operating screen with vertical edges plumb and viewing surface flat whenscreen is lowered.

3. Install low-voltage controls according to NFPA 70 and manufacturer's written instructions.4. Install projection screen units and accessories at locations shown, in accordance with

manufacturer's instructions. Install level, plumb, secure and at proper height.B. Seismic Restraints:

1. Secure all hanging and freestanding equipment to building structure so that it resistsseismic acceleration of 1g in any direction.

2. Comply with the local building codes and the most recent version of the UBC.3. Submit calculations and detailed details stamped by a registered engineer.4. The seismic restraints are not shown on the Contract Drawings. It is the Contractor’s

responsibility to develop shop drawings that reflect the field condition and the seismicrequirements.

5. The equipment restraints are not shown on the Contract Drawings. It is the Contractor’sresponsibility to develop shop drawings that reflect the field condition and the restraintrequirements.

3.03 EQUIPMENT MOUNTING.A. Category AVS Drawings are for information only. Supply Shop Drawings demonstrating the

mounting methods stamped by a registered structural engineer prior to installation.3.04 INSTALLED CABLE

A. Reference Division 27 Section “Audio-Video Systems”3.05 SYSTEM GROUNDING

A. Reference Division 27 Section “Audio-Video Systems”3.06 FIELD QUALITY CONTROL

A. The finished installation shall be free from damage, flaws, blemishes or other defectsdetrimental to appearance; have doors and acoustical overlay at doors in alignment withadjacent acoustical ceiling and be uniform in plane.

B. Provide protection as required to ensure satisfactory operation and appearance at completion ofproject.

C. Manufacturer's Field Services: Engage a factory-authorized service representative to test andadjust projection screens.

D. Schedule visual and mechanical inspections and electrical tests with at least seven days'advance notice.

E. Inspect projection screen components for defects, physical damage, testing laboratory labeling,and nameplate compliance with the Contract Documents.

F. Electrical Tests: Use particular caution when testing devices containing solid-state components.Perform the following according to manufacturer's written instructions:1. Continuity tests of circuits.2. Operational Tests: Set and operate controls to demonstrate their functions and capabilities

in a methodical sequence that reproduces actual operating functions.3. Where light balancing or other control involving equipment provided under other Sections

is indicated, combine testing required by this Section with that required by Sectionsspecifying other equipment. Test programmable control related to light balancing,occupancy sensing, and other controls under conditions that simulate actual operationalconditions. Record control settings, operations, cues, and functional observations.




G. Correct deficiencies, make necessary adjustments, and retest. Verify that specifiedrequirements are met.

H. Project Management:1. Participate in all Project Meetings. Be present at the Project site for Substantial Completion

Inspection, Final Inspection, approve the operating and maintenance manuals, and provideany additional instruction as needed to designated members of the Owner's staff.

2. Be responsible for supervision of all technical work that is part of this Section3. Supervise preparation of shop drawings and submittals and sign all submittals.4. Supervise shop fabrication and field installation work to assure conformance with the

Contract Drawings, the Specifications, and the reviewed Shop Drawings to assureworkmanship of the specified quality.

5. Oversee the testing of all assemblies and sub-assemblies prior to delivery to the ProjectSite.

6. Lead in the specified testing of the completed installation to assure the Owner that allContract Requirements are met. Work with and assist the Owner in the final testing forapproval and acceptance of the system for the Owner.

3.07 ADJUSTING AND TESTINGA. General:

1. Testing will include but is not limited to those listed below in order to verify that the systemmeets all design and performance requirements. Testing includes pre-installation and postinstallation testing.

2. Perform the testing and adjustment prior to scheduling the Owner’s Representative toattend the Substantial Completion Inspection.

3. Document the test results and submit them in accordance with the submittal procedures.After acceptance, incorporate all test documentation into the system manual.

4. Assist the Owner’s representative during the Substantial Completion Inspection inperforming final system adjustments and acceptance tests. Providing all labor, materialsand tools necessary for these tests and adjustments and all necessary test equipment tocomplete the tests.

5. When all the tests have been completed and the system is ready for inspection, formallynotify the Owner’s Representative at least seven working days prior to AcceptanceTesting. Include in this notice copies of all data recorded, date each test was completedand the results of each test. All test data shall be available during the inspection process.

6. Test electrically operated units to verify that screen controls, limit switches, closure, andother operating components are in optimum functioning condition.

7. Test manually operated units to verify that screen operating components are in optimumfunctioning condition.

B. Verification:1. Verify that all wiring is installed correctly and completely. Verify that there are no short

circuits or open circuits.2. Prior to energizing or testing the system, ensure the following:

a. All products are installed in a proper and safe manner per the manufacturer’sinstructions.

b. Insulation and shrink tubing are present where required.c. Dust and debris is removed.d. Cable is dressed, routed, and labeled.e. All labeling has been provided.f. Temporary facilities and utilities have been properly disconnected, removed and

disposed off-site.g. Electronic devices are properly grounded.




3.08 CLEANINGA. Clean all provided equipment and devices internally and externally using methods and materials

recommended by manufacturers.B. All of the equipment shall be free from dust at the time of the Substantial Completion Inspection

and the Final Inspection.C. Repair damaged finishes.D. Clean projection screens on both faces immediately before date scheduled for inspection

intended to establish date of Substantial Completion. Use methods and cleaning materialsrecommended by screen manufacturer, taking care not to scratch or damage optical coatings orscreen substrates.

3.09 SUBSTANTIAL COMPLETION INSPECTIONA. General:

1. Notify the Owner’s Representative in writing that the system has met all of therequirements for Substantial Completion and is ready for the Substantial CompletionInspection two weeks prior to the Inspection. The notice must be written and signed by themajority shareholder if the company is a closely held corporation or the President in apublically traded company or Sole Proprietorship.

2. Provide the services of the Project Engineer described above, the Project Manager and afield service technician to the Owners Representative to make adjustments during theSubstantial Completion Inspection.

3. Assist the Owner’s Representative in performing final system tests and adjustments.4. Provide all labor, materials, tools and test equipment necessary for these tests and

adjustments.B. System Demonstration:

1. Demonstrate the:a. Overall system operation.b. Control system operation.c. DSP software control operation.d. Optics system field performance.e. Electro-acoustic field performance.f. Audio system field performance.g. Video system field performance.h. Production Communications system field performance.i. RF system field performance.j. Performance Tests verification (as described in Part 3 of this Section).

C. Loose Equipment and Documentation:1. Provide the following items on-site for inspection:

a. Operations and Service Manual.b. Shop Drawings.c. Portable Equipment.d. Shop Test Report.e. Field Test Report.

D. Failure:1. In the event that the system fails to meet the criteria for Substantial Completion all of the

costs for additional inspections shall be borne solely by the Contractor. Costs include:a. Consulting fees.b. Travel and daily expenses.

E. Deficiencies:




1. After the Substantial Completion Inspection the Owner’s Representative will issue a reportdocumenting the system deficiencies.

3.10 FINAL INSPECTION AND ACCEPTANCE:A. Notify the Owner’s Representative in writing that the system has met all of the requirements for

Final Inspection and is ready for the Final Inspection two weeks prior to the Inspection andE-mail digital photographs of the corrected deficiencies from the Substantial CompletionInspection.

B. Provide the services of the Project Engineer described above, the Project Manager and a fieldservice technician to the Owners Representative to make adjustments during the FinalInspection.

C. Assist the Owner’s Representative in performing final system tests and adjustments.D. Provide all labor, materials, tools and test equipment necessary for these tests and

adjustments.E. Final acceptance of the installation will be granted when it is clear to the Owner’s

Representative that the following conditions have been met:1. All of the deficiencies documented in the Substantial Completion Inspection Report have

been corrected.2. All fixed equipment has been furnished, programmed and installed according to the

drawings and specifications.3. All portable equipment has been turned over to the Owner.4. All equipment has been tested individually and as a completed assembly performs as

specified.5. The Operations and Service Manual and As-Built Documentation have been completed,

approved and delivered to the Owner.3.11 DEMONSTRATION

A. General:1. Demonstrate the device meets all of the specifications during the Substantial Completion

Inspection.2. Notify the Owner’s Representative in writing that the system has met all of the

requirements for Training and is ready for Training two weeks prior to Training.3. Train the Owner after all of the deficiencies documented in the Substantial Completion

Inspection have been corrected and observed by the Owner’s Representative.3.12 PROTECTION

A. General:1. After the audio-video system has been installed in the field, protect the audio-video system

from damage during construction. If damage occurs despite such protection, remove andreplace damaged components or entire unit as required to provide units in their original,undamaged condition.

2. Provide temporary covering of the audio-video system components until time ofSubstantial Completion.

3. See Part 1 if this Section for the Project Site Conditions requirements.END OF SECTION



10/9/2019 PORTABLE DANCE FLOORSYSTEM

11 6171-1

SECTION 11 6171PORTABLE DANCE FLOOR SYSTEM

PART 1 - GENERAL1.01 SUMMARY

A. Portable Dance Floor System comprised of vinyl sheet flooring to provide the appropriate floorsurface for dance, for use on top of the permanent resilient floor of the stage.

1.02 SECTION INCLUDES:A. Work in the following spaces:

1. Proscenium TheatreB. Systems:

1. Vinyl sheet flooring with hook and loop straps2. Rolling dance floor storage rack3. Vinyl tape4. Cleaning supplies5. Signage6. Operations and Maintenance (O&M) Manuals

C. Provision of materials, components, modifications, assemblies, equipment and services asspecified herein, including but not limited to:1. Verification of site dimensions and conditions2. Submittals as required by the Contract Documents3. Manufacture of equipment and systems as required by the Contract Documents4. Scheduling, sequencing and coordination with work specified in other sections5. Installation and site supervision of equipment and systems specified herein and elsewhere

in the Contract Documents6. Demonstration of equipment and systems as specified herein and elsewhere in the

Contract Documents7. Instruction to the Owner on installation, storage and maintenance

1.03 RELATED SECTIONS:A. Division 01: General Requirements:B. Division 9: Finishes

1.04 DEFINITIONSA. PDF: portable document file.

1.05 SYSTEM DESCRIPTIONA. Design Requirements

1. Provide a portable dance floor for use during dance rehearsals and performances. Includeaccessories needed to provide a complete system. Include roll carrier dance floor rack tostore and transport the flooring when not in use.

B. Performance Requirements:1. Size:

a. Size to cover approximately 30’ deep X 50’ wide floor area. Floor shall extend to stagefront edge. Use custom cut panels if required.

b. Separate floor panels to cover orchestra pit if used as stage front extension. Panels tobe custom cut to stage front shape.

c. Nominal maximum panel size of 60 feet long by 78.5 inches wide2. System surface effect shall perform evenly and consistently regardless of ambient

temperature and humidity.3. System is 100 percent portable.




11 6171-2

4. Floor shall not make excessive noise under impact from dancers, including binding orcracking.

1.06 SUBMITTALSA. All submittals shall be in accordance with Division 1. All submittals shall be submitted within 90

days of bid award, allowing sufficient time for adequate review and possible resubmittal withoutjeopardizing the project schedule.

B. Shop Drawings:1. All submittals shall be complete. No partial submittals shall be allowed without the Theatre

Consultant’s prior written consent.2. Drawings will show all information necessary to explain fully the design features,

appearance, function, fabrication, installation and use of system components in all phasesof operation.a. Show floor layout in plan view, indicating all panels.

3. Fabrication, installation or erection shall not commence until shop drawings have beenreviewed by the Theatre Consultant.

4. All sheets in the submittal shall be of the same size.5. Submittal shall include a title sheet listing all sheets in the submittal.

C. Record Documents:1. Record Documents shall be submitted in accordance with Division 1.2. Provide three (3) bound copies of the Operations and Maintenance Manuals. Manuals

shall include:a. Contact informationb. Safety and Operational Instructionsc. Complete parts and subassembly listd. Periodic Maintenance Schedulee. Maintenance procedure for finishesf. Diagrams depicting the system layout and maximum load limitations, drawn not less

than 1/4 inch = 1'-0"3. Provide three (3) hard copies of shop drawings, including updates or revisions to the

original submission, to accurately reflect the installed system.4. Provide three (3) copies of the following electronic files:

a. Final shop drawings in their native electronic files (AutoCAD or similar)b. Submittal files, including shop drawings, in a PDF formatc. Submit files on standard pc format CD clearly labeled with project name, project

architect, theatre consultant, contractor name, and date of submittal.1.07 DELIVERY, STORAGE, AND HANDLING

A. Acceptance at Site:1. Deliver equipment to the site only after the building has been closed in.

B. Storage and Protection:1. Coordinate storage at the site and ensure the materials and components are undamaged.

1.08 WARRANTYA. Special Warranty:

1. Warrant systems and equipment to be free of defective components, faulty workmanship,or improper adjustment for a period of two (2) years from the date of Owner’s acceptance. Paint and exterior finishes are excluded. Replace items showing evidence of defectivematerials or workmanship (including installation workmanship) within thirty (30) days afternotification. Make replacements without cost to the Owner.

2. Rectify conditions that might present a hazard to human life, well-being, and/or propertywithin forty-eight (48) hours of notification.




11 6171-3

1.09 COMMISSIONINGA. Provide demonstration and testing of systems described in this section. Training shall be made

part of the system demonstration.1.10 MAINTENANCE

A. Maintenance Service:1. Provide maintenance service for a period of one (1) year after final acceptance of the

product.PART 2 - PRODUCTS2.01 MANUFACTURERS

A. Provide material (except where otherwise stated) by one of the following fabricators:1. Harlequin "FreeStyle"2. As approved alternative

2.02 MATERIALSA. Vinyl Sheet Flooring:

1. Color: Black.2. Thickness: Minimum 0.180 inch.3. Roll width: 59 inch4. Weight: Minimum of 4.9 pounds per square yard5. Dimensional stability, flexibility, and residual indentation in compliance with British

Standard (BS) 3261: Type A.6. Fire rating: ASTM E648, E662 – Class 1

B. Storage Rack:1. Provide rolling storage racks of steel tube construction suitable for storage of up to six (6)

rolls of dance floor each and accessories. Provide in quantity to store the all rolls provided.2. Racks shall be sized for narrowest passageway in facility.3. Caster will be sized not to damage the dance floor covering.4. Racks shall be designed to allow the speedy rolling of the floor roll directly onto the storage

rack, to prevent double handling of the dance floor.C. Vinyl Flooring Accessories: Provide the following accessories in quantities as noted:

1. PVC Vinyl floor tape suitable for use with Vinyl Dance flooring, in quantities to achieve six(6) full installations – approximately 900 yards:a. Black

2. All-purpose cleaner as recommended by the manufacturer – one case3. Heavy duty floor cleaner as recommended by the manufacturer – one case4. Binding straps fabricated from hook and loop tape, in quantities to secure all flooring rolls

in storage.5. Walk along tape applicator: Qty (1).

a. GaffTech: GaffGun.b. Or approved equal

2.03 SOURCE QUALITY CONTROLA. Tests, Inspection

1. Work on the systems may be inspected at the point of manufacture a minimum of one (1)time during fabrication. This review will occur during the final factory checkout prior toshipping, unless the Manufacturer and Theatre Consultant agree on a more advantageousreview date.

PART 3 - EXECUTION3.01 INSTALLATION

A. Deliver flooring material and provide one installation for demonstration.




11 6171-4

1. Install and demonstrate the entire floor, including the custom trimmed stage front area2. Taping floor is not required.3. Demonstrate black side only.

3.02 INSPECTION & TESTSA. Demonstrate compliance with tolerances specified in the Contract Documents.

3.03 DEMONSTRATIONA. Final review will be made by the Theatre Consultant following receipt in writing or notification

from the Contractor that the material has been delivered and cut with custom shapes.B. If review reveals any detail of construction, fabrication, not in strict accord with the Specification

and Contract requirements, approval will be withheld and Contractor shall be given thirty (30)days to replace the rejected items with those conforming to specification requirements.

END OF SECTION



10/16/2019 LOOSE AUDIENCE SEATING

12 6211-1

SECTION 12 6211

LOOSE AUDIENCE SEATING

PART 1 - GENERAL

1.01 SUMMARY

A. Fully upholstered free-standing chairs, materials and services as specified herein:

1. See Drawings for location and quantities.

2. Spare Parts: Two (2) percent of all parts, minimum of one (1).

1.02 SECTION INCLUDES:

A. Seating units are to be provided for the following space:

1. Multipurpose Hall

B. Approximately 140 21 upholstered free-standing chairs, with arms, materials and appropriateaccessories. Specific chair style and fabric will be chosen by Architect. See Drawings forseating layouts and locations.

C. Materials, component modifications, assemblies, equipment and services as specified herein. These include, but are not limited to:

1. Submission of Shop Drawings, certificates, test reports and approvals as specified herein

2. Inspection, alignment, and final adjustment of completed installation; demonstration forreview

D. Systems:

1. Furnish equipment and hardware in addition to the items specified previously that arenecessary to provide a fully working system in conformance with the intent of the ContractDocuments.

2. Contractors are required to identify all specification items that their product does notconform to at the time of bidding.

1.03 RELATED SECTIONS:

A. Section 12 66 23: Telescopic Seating Platform

1. Fabric for this section provided by 12 66 23

1.04 SYSTEM DESCRIPTION

A. Design Requirements:

1. The intent of the Work is to provide safe, efficient method of audience seating conformingto the performance and aesthetic requirements herein and elsewhere in the ContractDocuments.

2. Chair dimensions: the following are the maximum dimensions for the loose chair:

a. Seat Height: 18 inches

b. Seat Back Height: 32 inches

c. Seat Depth: 21.5 inches

d. Seat Width: 21.5 inches

e. Armrest Height: 26 inches

f. COM yardage: 1-1/8

1.05 SUBMITTALS

A. Shop Drawings:

1. Provide Submittals in accordance with Division 1. Submit in a timely manner, allowingsufficient time for adequate review and possible resubmittal without jeopardizing theproject schedule.

2. Submit Shop Drawings or product cut sheets within ninety (90) days of award of contract.

3. Provide complete Submittals. No partial Submittals shall be allowed.




12 6211-2

4. Drawings will show all information necessary to explain fully the design features,appearance, function, fabrication, installation and use of system components in all phasesof operation.

5. Fabrication, installation and erection shall not commence until Shop Drawings have beenreviewed and marked by the Theatre Consultant.

6. All sheets in the Submittal shall be of the same size.

7. Submittal shall have a title sheet listing included sheets.

B. Samples:

1. In addition to the samples required for substitutions, provide the following non-returnablesamples within forty-five (45) days of bid acceptance. Pay shipping charges incurred.

a. Provide samples for selection and verification purposes of each exposed materialfrom which seating units and accessories are composed, in each color, finish, pattern,and texture indicated. Include samples of the following:

1) Fabric swatches

b. Submit one (1) seat of each type to the Architect for approval. These chairs may beincorporated into the work as spare parts at completion.

1.06 QUALITY ASSURANCE

A. Qualifications

1. This Contractor and all subcontractors shall have been an authorized representative of themanufacturer of the specified equipment and systems for a minimum of five (5) years. The Architect shall be the final judge of suitability of experience.

2. No sub-contracting work is permissible, unless the sub-contractor is named and includedas part of the bid.

3. The Architect will have the right to inspect any previous equipment or systems as furnishedor installed by this Contractor. In addition, the right is reserved by the Consultant to rejecta Contractor who has failed in any respect to comply with every provision of any previouscontract.

4. Demonstrate that spare parts and service personnel are, and shall continue to be, readilyavailable for the Work specified.

B. Certifications

1. Submit applicable flame retardant certificates.

1.07 PROJECT CONDITIONS

A. Existing Conditions

1. Survey and document field measurements prior to the commencement of shop drawingsand again prior to delivery and installation of the system.

1.08 SEQUENCING

A. Schedule and sequence the Work in conjunction and agreement with trades performing related,adjacent and intersecting work and the General Contractor. Accommodate the Owner’sprojected time schedule for installation, particularly where coordination with other trades isrequired.

B. Coordinate the Work with related trades; this includes the preparation of schedules andcoordination of equipment delivery and storage.

1.09 WARRANTY

A. Special Warranty

1. Warrant the work to be free of defective components, faulty workmanship, and improperadjustment for a period of two (2) years from the date of owner’s acceptance. Replaceitems showing evidence of defective materials or workmanship (including installationworkmanship) within thirty (30) days after notification. Make replacements without cost tothe Owner.




12 6211-3

2. Designate warranties on manufactured equipment to the Owner on the date of systemacceptance.

PART 2 - PRODUCTS

2.01 PRE-APPROVED THEATRICAL SUBCONTRACTORS

A. The following loose audience seating system specialty subcontractors have been pre-approvedfor bidding for the work in this section:

1. PS Furniture - Model: Acton Stacker

a. Local Dealer: Tom Polito, Polito Associates, 1350 Reynolds Ave, Suite 101, Irvine, CA92614; Phone: 949-433-3405, email [email protected]

2. Hussey Seating - Model: HDS Stacking Chair, Arm Chair Standard Size

a. 3 Centurion Way, Crusader Park, Warminster, Wiltshire, BA12 8BT U.K.

1) Phone: +44 (0)1985 847200

B. Non-preapproved specialty subcontractors

1. All other contractors must be approved prior to bid.

2. Other contractors seeking acceptance must submit the following information at least 2weeks prior to the bid opening date.

3. Failure to submit any of the required information will automatically disqualify the contractorfrom consideration of approval.

a. A listing of five equivalent installations including:

1) Name, address and telephone number of contractor;

2) Name, address and telephone number of Theatre Consultant;

3) Scope of work.

4) A brief written description of the contractor's operation including facilities,financial capabilities, key personnel, and experience of key personnel.

5) If required, a statement from a bonding company agreeing to provide therequired bonds in the amount required for the project.

4. Permission to bid does not imply acceptance of the specialty subcontractor. It is the soleresponsibility of the contractor for this Section to ensure that any price quotations receivedand submittals made are for systems that meet or exceed the specifications.

2.02 MATERIALS

A. Employ parts and materials that are new and undamaged.

B. Padding Materials:

1. Provide seat and back padding material of new (prime manufacture) polyurethane foam.

2. Testing: California Technical Bulletin 117-2013 - Requirement, Test Procedure andApparatus for Testing the Smolder Resistance of Materials Used in Upholstered Furniture,June 2013

a. The use of fire retardant chemicals to meet the requirements of this bulletin is notacceptable.

C. Fabric: (to match telescopic seating)

1. To be provided by Section 12 66 23.

2. Testing:

a. California Technical Bulletin 117-2013 - Requirement, Test Procedure and Apparatusfor Testing the Smolder Resistance of Materials Used in Upholstered Furniture, June2013

1) The use of fire retardant chemicals to meet the requirements of this bulletin isnot acceptable.

b. ASTM D 4157-02 or current approved ASTM standard - Standard Test Method forAbrasion Resistance of Textile Fabrics (Oscillatory Cylinder Method)

1) Meet or exceed 50,000 rubs with #10 cotton duck (Wyzenbeek apparatus).

c. AATCC 16 Option 1 or 3 - Fabric Colorfastness to Light




12 6211-4

1) Grade 4 minimum at 40 hours

d. Brush Pill ASTM D3511 - Class 3 minimum

e. Breaking Strength ASTM D5034 (Grab Test) - 50 lbs. minimum in warp and weft

f. Seam Slippage ASTM D4034 - 25 lbs. minimum in warp and weft

g. AATCC 8 - Crocking

1) Dry Crocking Grade 4 minimum

2) Wet Crocking Grade 3 minimum

D. Armrests:

1. Provide black satin reinforced molded polymer.

E. Frames:

1. 14-gauge tubular steel frame design, with 16-gauge steel inner reinforcement.

2.03 FINISHES

A. Shop Finishing

1. Finish: Match fixed seating, per Architect’s selection.

2. Hardware: All assembly hardware shall be concealed, rust resistant, and black plated.

B. Metal Parts: Protect metal parts with a five-stage bonderization process prior to application ofpowder coat finish. Finish metal parts in electrostatically-applied powder coat finish. Architect toselect color from manufacturer’s full color range.

2.04 ACCESSORIES

A. Storage cart:

1. Provide cart sized for storage and transportation of all stack chairs.

B. Ganging:

1. Provide ganging attachment.

PART 3 - EXECUTION

3.01 EXAMINATION

A. Site Verification of Conditions

1. Examine work prepared by others to receive work of this Section and report defectsaffecting installation to the Construction Manager for correction. Commencement of thework shall indicate complete acceptance of preparatory work by others. Inspectionincludes but is not limited to:

a. Protect the surrounding environment from damage by the Work.

b. Deliver equipment to the site only after the building has been closed in. Coordinatestorage at the site with the Owner and ensure the materials and components areundamaged.

c. Remove debris caused by this work from the premises.

3.02 FIELD QUALITY CONTROL

A. Site Tests, Inspection

1. Final inspection shall be made by Theatre Consultant, following receipt in writing ornotification from this Contractor that the installation is complete. If inspection reveals anydetail of construction, fabrication, or installation not in strict accord with the Contractrequirements, approval shall be withheld and Contractor shall be given ten (10) days toreplace the rejected items with those conforming to specification requirements. Previousinspections do not eliminate the possibility of rejection during the final inspection.

3.03 DEMONSTRATION

A. Contractor is required to facilitate the Consultant/Architect commissioning of the loose seating. This commissioning will include but is not limited to the following items.

1. Verify that loose and installed seating quantities are as contracted.

2. Verify delivery of all specified spare parts, materials, etc.




12 6211-5

3. Check alignment for smooth, quiet, reliable operation of all seats.

4. Inspect structural attachments of seating.

5. Inspect seating for material and workmanship per specification.

6. Review warranty certificate.

3.04 PROTECTION

A. Following installation, protect the seating from damage with appropriate covers to be removedon final acceptance.

END OF SECTION



10/9/2019 AUDIO-VIDEO SYSTEMS27 4100-1

SECTION 27 4100AUDIO-VIDEO SYSTEMS

PART 1 - GENERAL1.01 SUMMARY


B. Section Includes:1. Sound system2. Video system3. Audiovisual system4. Production communications system5. Control system for audio-video system6. CATV system7. Cable, wiring, connection devices for wiring system to be used as signal pathways for

audio-video, production communications and control system1.02 RELATED SECTIONS:

A. Division 26: Section “Raceways and boxes for Audio-Video Systems”B. Division 11: Section “Projection Screens”C. Division 27: Section “Portable Audio-Video Equipment”D. Allowances:

1. Allow $7,500.00 for equipment and installation that will be specified after the SubstantialCompletion Inspection. Credit the Allowance amount to the Owner if no additionalequipment is specified. If the Owner does not use the entire Allowance credit thedifference.

E. Measurement procedures:1. Product quantity is as required.2. Some equipment is shown on the Drawings and required as part of the Portable

Audio-Visual Equipment specification Division 27 41 19. The total quantity requirement isthe sum of the equipment show on the Drawings and the specific quantity listed in theSpecifications.

3. Some product listed under this section may not be required to fulfill the obligations of theWork.

1.03 DEFINITIONSA. For purposes of the Contract Documents, these words and phrases are defined as follows:

1. Fully Operational: A system that meets or exceeds all of the requirements set forth in theContract Documents and is ready for the Final Inspection described in Part 3 of thisSection.

2. Fabricator’s Shop: The address listed on the Business License of the entity responsible forfabricating the Work specified in this Section.

3. Provide: Furnish, install, program, document, test and demonstrate4. AV: Audio-Video, Audiovisual5. EAV: Audiovisual infrastructure category drawings6. AVS: Audiovisual System category drawings7. AES: Audio Engineering Society8. ANSI: American National Standards Institute9. ASA: Acoustical Society of America10. ICIA: International Communications Industries Association11. NAB: Nation Association of Broadcasters12. SMPTE: Society of Motion Picture and Television Engineers




13. EMI: Electromagnetic interference14. GN: Generic

1.04 SYSTEM DESCRIPTIONA. General:

1. The following is intended to provide an overview of the design concepts and is not anexhaustive description of the related systems.

2. AV System Description:a. General:

1) The following audiovisual system functional description reflects the Owner’sprogrammatic requirements as documented in our programming interview withstakeholders on August 24th, 2017

2) The functional descriptions below will govern the audiovisual system designs thatwill be developed into the Contract Documents, Plans and Specifications. TheContractor will bid and build the work shown on the Contract Documents.

3) The principal design goal will be to minimize the interaction required by the staffto operate the audiovisual system, provide flexibility for future expansion andminimize the impact of the audiovisual system devices on the architecture. Theresult will be an audiovisual system that is unobtrusive to the audience,presenters and system operators.

3. Conduit Pathway and AC Power Infrastructurea. Analog wiring will be run in ferrous metal conduit from the equipment racks to the

remote connection and equipment locations in the field. Conduit for analog signals inconcrete will be coated-ridged. Ferrous metal conduit provides EMI shielding forextremely low voltage signals like microphone (1mV.) and line level (1V.) audio andvideo from electromagnetically induced interference inherent to high voltage lines thatcan introduce hum and noise into the AV system and protects the individual cablesfrom damage.

4. Digital signals are not subject to EMI in levels found in standard building construction. Pathways for digital signal cable will be metallic conduit. Digital signal cable pathways inconcrete will be PVC conduit.a. The AV systems will be powered from a dedicated isolation transformer with a

dedicated isolated technical ground specific to the audiovisual system. Thisgrounding scheme minimizes the possibility of other equipment introducing noise intothe audiovisual system through the building AC power ground.

b. To eliminate signal interference introduced through the conduit grounding system, theconduit for the audiovisual system will be bonded to the general building ground. Theaudiovisual system signal ground will be isolated from the conduit and building powerground, bonded at the AV technical ground power panel.

5. Power Sequencea. The power for the AV system will be controlled and sequenced. The AC power for the

control system, digital signal processing and every device with an IP address will beconstantly powered.

b. Power Sequence On: The power sequencing system will energize the power to thesource equipment first then all processing equipment, then all of the power amplifiersin intervals no greater than 18 amps. Each power sequence will be separated by a .3second delay.

c. Power Sequence Off: The power sequencing system will de-energize the power tothe source equipment in the reverse order. The Delay will be set to one second toallow the power capacitors in the power amplifier to completely de-energize, theneach successive power sequence will sequence.

d. The AV system power sequencing system will be connected to the fire alarm panelwith a supervised control line. The supervised control line maintains a constantvoltage to the dry contact closures on the power sequencing system and the fire




alarm panel. A fire alarm event will de-energize the power to the control line andremove power from the AV system.

6. Multi-Purpose Rooma. General:

1) The Multi-Purpose Room (MPR) will function as a flexible event space foracoustic, amplified music, drama, dance, musicals, choral performances andlecture events.

2) Events will include: 55 person wind orchestra 20-30 person string orchestra, 20piece jazz band with and without vocals, band camp, ballet, drumline, choir, jazzchoir, guitar, pop show, rock show, hip-hop dance, fall concert, chamber group,march festival, winter concert, spring concert live band, dinner theater, statetesting, and video lecture presentations.

3) The audio-visual system will be designed to accommodate the followingfunctions: speech reinforcement, program audio reinforcement, videopresentation, live performance recording and outside productions.

4) Staffing:(a) Support personnel, trained student or professional operators will be required

to enable the AV system’s fullest potential.(b) There will be a simplified version of the sound system and video

presentation system that will operate using a control system that a novicewith minimal training will be able to operate.

5) User Interface:(a) A control system will be used to control many of the system’s operations.

The control system will control lighting presets, audio system, AV presets,and the presentation system functions.

6) Sound Reinforcement System:(a) Left Center Right Program Reinforcement Loudspeakers: The main

loudspeaker system will consist of left, center right powered loudspeakerarrays. These loudspeaker arrays will be hung above the stage area and beable to be lowered to the stage for servicing. The array loudspeakers will beincorporated into the design of the architecture so their appearance isminimized to the viewing audience.

(b) Subwoofers: Separate subwoofers will be used in addition to the main left,center, right loudspeaker clusters. The subwoofers cover only the very lowend of the audio spectrum and are used to enhance bass response formusic and special effects.

(c) Multi-channel and Effects Loudspeakers: Loudspeaker outlets will beprovided in the rear of the hall to provide reinforcement for ‘5.1’multi-channel effects.

7) Control Suite - Mix Position:(a) The mix position will be the primary location to mix audio for live

performances. The mix position equipment will include a digital mixingconsole, source equipment and production communications connections.

8) Digital Recording:(a) There will be a computer software based digital audio workstation (DAW)

recording system connected to the digital audio transport using DANTE. The DAW will have independent control of the audio signals.

9) Presentation support:(a) There will be support for a lecture presentation behind. It will include a

control touch panel, source equipment and HD computer inputs to the AVsystem.

10) Wireless Microphones:




(a) There will be wireless microphones transmitters, receivers and varioustypes of microphones. The microphones will be a mix of handheld, lapeland head worn.

11) Equipment racks(a) The equipment racks will be located in the control suite.

12) Stage Equipment:(a) There will be input panels on the stage for microphone and line level inputs,

monitor loudspeakers, video monitors, high-resolution video devices, andother equipment. Stage monitor loudspeakers and amplifiers, microphones,stands and other ancillary equipment will be part of the portable equipmentpackage.

(b) There will be several microphone inputs distributed throughout the MPR forrecording.

13) Stage Manager(a) Locations for the stage manager will be provided off-stage left, right and in

the control suite. These locations will include production communications,paging microphone, video and audio performance monitoring.

14) Technical Table:(a) A technical location in the forward third of the MPR. The tech table will have

production intercom a microphone and video input.15) Hearing Assistance System:

(a) The sound reinforcement system will include an infrared hearing assistancesystem. This will consist of a wireless transmission system with a pool ofreceivers for the audience. The ADA specifies providing 4 percent of theseating area with receivers.

16) Presentation System:17) The MPR will have a high definition presentation system to support lecture

events.18) Lectern

(a) Source equipment and user interface controls will be mounted in amulti-media lectern. The lectern will have a large working surface,equipment rack rails and a side drawer for a document camera.

(b) The audiovisual cable connecting the devices to and from the lectern will berouted through the bottom of the lectern to a floor-box to minimize trippinghazards. There will be a floor box on stage-right.

19) Source Equipment(a) The audiovisual system will have the following source equipment: Blu-Ray

DVD, document camera, inputs at the for HD video, HDMI, computer inputsfor both Macintosh and PC generated signals for the presenter’s laptopcomputer.

(b) The system will allow for variety of audio and video source equipment to beinserted into the system on a temporary basis. There will be connections inthe control room connected to the multimedia switch for source equipment.HD video with audio and HDMI connections, a Blu-Ray player and acomputer media drive at this location.

20) Audio and Video Switching(a) The AV switching system will be designed with HDMI signal technology.

21) Control System(a) The presentation system will be designed for automatic and manual

operation. Whenever possible the audiovisual system will be designed witha control system to minimize the interaction required by the presenter sothat no operator will be required for daily use of the basic functions. The




audiovisual system will also have an additional level of flexibility for morecomplicated operations.

(b) Remote Controls will minimize the interaction required by the users tooperate the AV system. The end user will have basic remote controlcapability of the audiovisual system components with an uncomplicatedbutton panel remote. The technician’s touch panel control will have morecomprehensive control of the Av system. The technician will have controlover system on/off, projection screen up/down, program audio volumeup/down/mute. In addition, it will control systems external to the audiovisualsystem (TBD).

(c) Transport control, play, stop, pause, forward and reverse will be controlleddirectly from the front of the source equipment and the control touch panel.

(d) The control system will have the ability to be remotely monitored bytechnical staff through the campus network. Crestron RoomView softwarewill be implemented by the contractor with the assistance of the controlsystem manufacturer.

22) Video Projection(a) HD video will be displayed with a projector in the projector room above the

Control Suite. The projector will have a motorized lens that will be able tofocus on two projection screen locations.

(b) The video projector will display HDMI connection. The video projector willhave a minimum light output capable of 55 to 75 ANSI Lumens per squarefoot of projected image and a native resolution of WUXGA.

(c) When possible all of the video sources will be native 1080P, 720P. Somevideo sources will need to be scaled to the native resolution of the projectorLCD panels (1080P).

(d) The video projector will be connected to the network and send email statusof lamp life.

(e) The projector will be equipped with remote mouse annotation forhighlighting projected images.

23) Projection Screen(a) The motorized projection screen will be sized to be 1/5 of the viewing

diagonal. The projection screen will have a tensioning system to minimizedistortion and a screen gain of .9. The .9 screen gain aids the videoprojector to produce a higher contrast ratio for higher classroom ambientlight conditions. The projection screen image format ratio will match thenative resolution of the projector (16:10).

(b) The projection screen will be controlled by the control system and withparallel controls in the control suite.

24) Program Audio(a) Program audio for the presentation system will use the LCR speakers.

25) Portable Equipment(a) The portable equipment package will include portable equipment to support

the MPR. It will include monitor loudspeakers, portable cable, microphones,stands and other ancillary equipment.

7. Power Sequencing Programming:a. Program the power sequence as follows:

1) Power Sequence On:2) Energize the power to the source equipment then all processing equipment then

all of the power amplifiers in 15 Amp intervals. Delay each sequence by .3seconds.

3) Power Sequence Off:




(a) De-energize the power to the power amplifiers then all of the processingequipment then all of the source equipment. Delay the power amplifiersequence until the power capacitors completely de-energize then eachsuccessive sequence by 1 second.

(b) Uninterruptable Power - UPS:(1) Provide constant uninterruptable power for the following equipment

types, digital audio signal processors, digital video signal processors,control system, computer networks and computers.

8. Fire Alarm Event:a. De-Energize the power to the Audio-Video equipment when the fire alarm is activated.b. Maintain a constant voltage ‘supervised line’ from the fire alarm panel to the power

sequence control input. The fire alarm panel power is maintained when the fire alarmis not activated.

c. When the fire alarm panel triggers an event drop the line voltage to zero so that thepower sequencer activates the Power Sequence Off.

9. Remote Control System Software Descriptiona. General:

1) Provide programming for the remote control systems as described below andshown on the Category AVS Drawings.

2) The functional description below describes the basic functional parameters ofthe control system. Lay-out and program the touch panel based on the controldescription, the system description and the Programmer’s experience. TheContractor is expected to use a degree of creative license with the control panelmenu layout.

b. Logic:1) Use positive logic.2) Provide power sensors, video sync sensors or other equipment to ensure that

positive logic conditions are maintained. Command synchronization conflictsare unacceptable. This equipment is not shown on the drawings.

3) Continually poll the state of each device to monitor and report its current state tothe control panel.

4) Use the light or inverted illumination capabilities of the control devices to indicatethe system status.

c. Control protocol:1) Use IP, RS-232 or RS-422 control protocol. Use IR control transmission only if

IP and RS-232/485 protocols are not supported by the device.d. Programming Efficiently:

1) Link device functions so that the end users are required to make the fewestnumber button pushes possible to control the audio-video devices.

2) Use a default preset as part of the power-up sequence.3) The programming shall be “foolproof” so that no amount of button pushes can

“Lock-up” the system.e. Touch Panel:

1) Text and Icons:(a) Do not use abbreviations or acronyms.(b) Use graphical icons with alphanumeric labels.(c) Use ten point font minimum.(d) Maximize the button size to use all of the ‘real-estate’ available.(e) Maintain a uniform text and background contrast for each page.(f) Color:

(1) Use the Owner’s corporate color pallet.(2) Use contrasting color to highlight functions or current status.

10. Touch Panel




a. Title Screen:1) Locate the Owner’s logo in the center of the page. Activate the initial preset with

a button push in any location of the touch panel. Advance the control to the MainMenu screen and start the Power Sequence.(a) Help Menu:

(1) Provide a detailed touch sensitive help section to aid the operation anduse of the audio-visual system. The help section shall provide a“novice” user with enough information to use every aspect of theprogrammed, controllable equipment.

(b) Lighting Control:(1) Provide four lighting presets and off that parallel the lighting system

presets. Maintain the control state by polling the status of the lightingcontrol system.

(c) Main Menu:(1) Menu Tabs: Locate control tabs at the top of the control screen. The

control tabs will select controllable menu pages. Highlight the currentmenu tab.

(d) Permanently located on right half of all screens are controls for thefollowing:(1) Previous Menu or Home: Returns user to the previous selected menu

screen. (upper right hand corner)(2) Program Audio Up and Down buttons: Alters the master volume of the

program audio.(3) Microphone master volume Up and Down buttons: Alters the overall

microphone volume level.(4) Lighting Control as described.(5) Projection Screen Up and Down buttons: Activates front projection

screen.b. Media Presentation Specific Menu Tabs:

1) System on and off:2) Source Equipment Tab (one for each source device).

(a) Selects the source equipment menu and advances the user to the selectedsource equipment control screen.

(b) Stop button.(c) Play button.(d) Pause button.(e) REW button.(f) FFWD button.(g) Video Projector On/Off:

(1) On and Off buttons: Turns the video projector on and off.c. Sound System Control Page

1) Presets:(a) Default: Program the default stage of the system.(b) Events: Provide presets for each type of event. The events will be defined

by the Owner during Commissioning.(c) System States: Program preset states for:(d) Automatic microphone mixing(e) Manual mixing(f) Hybrid a mix of manual and automatic mixing, automatic microphone mixing

for speech and manual mixing for music(g) Level control

(1) Level control for each automatic microphone (AMIC)(2) Master level control




(h) Mute(1) Mute control for each individual microphone(2) Mute for the master volume

d. Video Matrix Router:1) General:

(a) Set up the video matrix switch similar to a broadcast router with sources,destinations, Presets, ‘Preview’ and ‘Take’.

(b) Audio follows video.(c) Account for each route so it can be recalled.(d) Layout the matrix router control page so that the source equipment

possibilities are on the left-hand side of the touch-panel, the destinationdevices are on the right-hand side of the touch-panel. Locate a ‘Preview’and a ‘Take’ button on the top of the control panel. Locate eight presetbuttons at the bottom of the page.

(e) When a sources is selected route the video to the ‘Preview’ monitor and theaudio to the audio monitors.

(f) After a source has been ‘Previewed’ it can them be routed or ‘any-or-all’destinations by selecting each destination device then ’Take’ sends thesource to the selected destination.

(g) Pressing any source will tell the end user where that source has beenrouted by highlighting the source and the destinations.

(h) Pressing preview and a source in that order will route the source to thepreview monitor without the possibility of a ‘Take’. This is a safety thatallows the end user to preview a source without the possibility of accidentlysending the route to a destination.

(i) Presets routs can be programmed to a preset button by selecting a routethen holding down a preset button for three seconds.

(j) Preset routs can be named.e. Audio Matrix Router:

1) General:(a) Use the Digital Signal Processor to create an audio matrix switch similar to

a broadcast router with Sources, Zones, Presets, ‘Preview’ and ‘Take’.(b) Account for each route so it can be recalled.(c) Layout the matrix router control page so that the source equipment

possibilities are on the left-hand side of the touch-panel, the destinationZones are on the right-hand side of the touch-panel. Locate a ‘Preview’ anda ‘Take’ button on the top of the control panel. Locate eight preset buttonsat the bottom of the page.

(d) When a sources is selected route the audio to the ‘Preview’ audio monitor.(e) After a source has been ‘Previewed’ it can them be routed or ‘any-or-all’

Zones by selecting each destination device then ’Take’ sends the source tothe selected Zone.

(f) Pressing any source will tell the end user where that source has beenrouted by highlighting the source and the Zone(s).

(g) Pressing preview and a Source in that order will route the Source to thepreview audio monitor without the possibility of a ‘Take’. This is a safetythat allows the end user to preview a source without the possibility ofaccidently sending the route to a zone.

(h) Presets routs can be programmed to a preset button by selecting a routethen holding down a preset button for three seconds.

(i) Preset routes can be named.1.05 SUBMITTALS

A. General:




1. Submit the following items in accordance with the General Conditions and Division 1.2. Only complete submittals will be reviewed; incomplete submittals will be rejected.3. Electronic Media:

a. In addition to the requirements in Division 1, submit all material on one solid-stateUSB drive and one full size paper copy of the Shop Drawings and the Product Data.1) The control system un-compiled source code.2) The audio digital signal processing (DSP) source file.3) The video digital signal processing / routing source file.4) All software source files required to make the hardware function.5) A list of the IP addresses for each device.6) A list of the usernames and passwords for each device.7) A list of usernames and passwords for the programming code.8) The Adobe Acrobat or Bluebeam .pdf copy of the Product Data Manufacturers

Equipment Specification Sheets in a single file.9) An Adobe Acrobat or Bluebeam .pdf copy of the System Operating Instruction

Manual in a single file.10) An Adobe Acrobat or Bluebeam .pdf copy of the Performance Tests in a single

file.11) An Adobe Acrobat or Bluebeam .pdf copy of the Autocad .DWG drawings in a

single file.12) The Project Autocad .DWG drawing files.

b. Software License:1) Provide the original software license for the software and firmware supplied with

the system.4. Installer Qualifications:

a. Provide the installer qualification information described in Part 1 Quality Assurance.5. Product Data:

a. Bill of Quantity: Provide a Bill of Quantity for each device specified in Part 2 and allincidental material supplied necessary to complete the Work as specified herein andshown on the Drawings.

b. Provide the following information for each item listed:1) Manufacturer's name.2) Manufacturer’s model number.3) Product description.4) Quantity supplied.

c. Manufacturers Equipment Specification Sheets:1) For each item specified in Part 2 submit a Manufacturer’s Equipment

Specification Sheet listing the product features, specification and physicalcharacteristics. If more than one product or model option is listed, Clearlyidentify which product is being submitted.

2) Tabulate each Manufacturer’s Equipment Specification Sheet using tab dividersin the same order as each item appears in Part 2 of this Section.

6. Shop Drawings:a. General:

1) Shop Drawings shall be clear and legible.2) Character height shall be 1/8-inch high when plotted at full scale.3) Draw all Shop Drawings using the most current version of AutoCAD by

Autodesk.4) Title character height shall be 1/4-inch when plotted at full scale.5) Drawings shall be 1/4-inch, 3/4-inch, 1-inch, 1-1/2-inch, 3-inch and 1-inch =

1-inch scale.b. Single Line Diagrams:




1) Separated the Single Line Diagrams in to audio, video, control, audio network,production communications, intercom, RF, broadcast and fiber system drawings.

2) Show the interconnection of all of the equipment in the signal path for eachsystem.

3) Include the following information for each piece of equipment:(a) Equipment manufacturer name.(b) Equipment manufactures model number.(c) Specialized part number option.(d) All input and output connection information, used or unused.(e) Location.(f) No drawing codes shall be permitted.(g) Coordinated with the bills of quantities.(h) Demonstrate the calculated estimated signal strength of the RF distribution

system based on the theoretical conduit path.(i) Include the following information for each cable:

(1) Equipment manufacturer name.(2) Equipment manufactures model number.(3) Cable designation number.(4) Termination locations.

(j) Include the following information for each field device:(1) Terminal cabinet number.(2) Intermediate pull box number.(3) Intermediate pull box size.(4) Field panel number.(5) Field panel connector number.(6) Location.

c. Plan View Drawings:1) General:

(a) Coordinate the Plan View Drawings with the Single Line Diagrams.(b) Clearly show and dimension the location and size of all devices.(c) Include the following for each cable in a Cable Schedule:

(1) Manufacturer name.(2) Manufacturer's model number.(3) Designation prefix.(4) Cable type.(5) Cable color.

(d) Detail the conduit fill. For each conduit run show the cable fill, include:(1) Cable designation.(2) Cable quantity.

d. Equipment Enclosure Elevations:1) Show the elevation view of all enclosed equipment and indicate the following

information:(a) Manufacturer's name.(b) Manufacturer’s model number.(c) Equipment enclosure location.(d) Equipment enclosure number.

e. Control Panel Menu Layouts:1) Document each control panel screen menu as described in Part 2 of this

Section.2) Document the menu logic tree for each control device.

f. Contractor Fabricated Equipment Drawings: For each contractor fabricated indicate:1) All components and equipment, including:




(a) Manufacturer's name.(b) Manufacturers model number.(c) Dimensions.(d) Component values.(e) Locations.(f) Mounting Drawings:

2) Equipment mounting per DSA approved plans.g. Samples:

1) Submit a sample for each piece of equipment visible in a public area.2) Submit a 4” swatch of the architectural grille cloth and a 4” swatch of the

immediate architectural surface.7. Shop Test Report:

a. General:1) Submit the test results of the test results from Part 3 of this Section.

8. Field Test Report:a. General:

1) Submit the test results of the test results from Part 3 of this Section.9. Substantial Completion Inspection Request:

a. Submit a Substantial Completion Inspection request letter certifying that all of thecriteria defined in the Contract Documents has been satisfied and the system is FullyOperational. The Request must be written on company letterhead and signed by theOwner, President or Majority Shareholder of the Contractor responsible for the Work.

10. Operations and Service Manual:a. General:

1) Compose the Manual using a single, consistent visual format and writing style.2) Portions of the Manual may be derived from the equipment manufacturer's

instruction manuals and may include reproductions of artwork and othermaterials.

3) Manual Organization:(a) Organize the Manual in a three ring binder.(b) Print the Manual using 24lb. bond paper.(c) Separate each Part with labeled tab dividers.(d) Tabulate each the Equipment Manual using tab dividers in the same order

as each item appears in Part 2 of this Section.b. Part I - Index, include:

1) Title page:(a) Project name.(b) Date.(c) Specification reference number.(d) Installers name and address.(e) Installers service phone number.

c. Part II - AV Network Information:1) List the IP addresses for each piece of equipment.2) List the usernames and passwords for each device.3) List the usernames and passwords for each software programming code.4) Document the network topology.

d. Part III - System Operating Instructions:1) Provide an overview of the System Description that describes the functionality of

the system.2) Provide comprehensive instructions for the operations of all the systems

specified in this Section.3) Provide comprehensive control system instructions, include:




(a) A button-by-button description for each menu for each touch panel. At thetop half of each page include a ‘screen shot’ of the control system touchpanel display being described.

(b) Button panel description for button panel.(c) Control system help section.(d) Provide comprehensive system operation instructions, include:

(1) Equipment front panel buttons and displays.(2) Custom equipment programming instructions.

e. Part IV - Equipment Information:1) For each piece of equipment specified in this Section, include:

(a) Manufacturer's installation, operating and service manual.f. Part V - Performance Tests:

1) Provide comprehensive documentation of all performance verification tests andprocedures described in Part 2 and Part 3 of this Section.

11. Record Drawings:a. General:

1) Develop the Record Drawings from the final As-Built condition of the system.2) Include the corrections from the Shop Drawing Submittal.3) Include all Changes as a result of Change Orders.

b. Mount one full-scale original of the As-Built Drawings plotted on 20 lb. bond paperbehind acrylic in the control room for each system.

12. Training Materials Submittal:a. General:

1) Provide all training materials for review prior to scheduling training sessions.13. Warranties: Special Warranty specified in this Section.

1.06 QUALITY ASSURANCEA. Regulatory Requirements:

1. Comply with the latest version of the ANSI, Cal-OSHA, IEC, IEEE, FCC, NEC and NFPArequirements.

2. Listed and labeled as defined in California Electrical Code by a testing agency acceptableto authorities having jurisdiction, and marked for intended use.

3. Equipment and materials shall be UL listed.4. Installer Qualifications:

a. The installer shall have the following experience, certifications and requirements:1) Authorized representative of equipment manufacturer for both installation and

maintenance of equipment required for this Section.2) Successfully completed a minimum of three projects of similar scope and size.

Provide letters of recommendation from the Owner’s Representative from thosethree projects.

3) Installation staff: ICIA CTS-I certification. Provide certification from ICIA.4) Engineering staff: ICIC CTS-D certification. Provide certification from ICIA.5) Support staff: ICIA CTS certification. Provide certification from ICIA.6) Control system programmer: Crestron Certified Master Programmer.7) Digital Media technician: The demonstration and acceptance tests shall be done

by a Crestron DigitalMedia Certified Engineer (DMC-E).b. The Work specified in this Section and Section 11 52 13 shall be accomplished by a

single Contractor experienced in the design, fabrication, installation, checkout andwarranty contract management of systems such as those described in each Section.1) Employ a qualified project engineer meeting the following requirements:

(a) Be a university graduate engineer in electrical or electronic engineering orphysics, and have at least 5 years experience with similar electronic and




optical specialty systems or other equivalent educational experience orbackground.

(b) Participation in meetings and conferences. Be present at the Project site forSubstantial Completion Inspection, Final Inspection, approve the operatingand maintenance manuals, and provide any additional instruction as neededto designated members of the Owner's staff.

(c) Be responsible for supervision of all technical work that is part of thisSection

(d) Supervise preparation of shop drawings and submittals and sign allsubmittals.

(e) Supervise shop fabrication and field installation work to assure conformancewith the Contract Drawings, the Specifications, and the reviewed ShopDrawings to assure workmanship of the specified quality.

(f) Oversee the testing of all assemblies and sub-assemblies prior to deliveryto the Project Site.

(g) Lead in the specified testing of the completed installation to assure theOwner that all Contract Requirements are met. Work with and assist theOwner in the final testing for approval and acceptance of the system for theOwner.

c. Prior to the bid submit the following in accordance with the Instruction to Bidders:1) A detailed brochure describing its capabilities.2) Examples of three similar installations within the past two five years.3) Distribution arrangements with manufacturers.

(a) Franchises.(b) Dealerships.(c) Distributorships.(d) Evidence of all necessary licenses and certificates to perform the specified

work.(e) Financial capability.(f) Bonding capability.(g) Identify all sources of labor.(h) Identify all local agents.(i) Identify all subcontractors.(j) Personnel experience background for the following people who will be

directly responsible for the Work specified herein:(1) Director of engineering.(2) Project engineer.(3) Project manager.(4) Control system programmer.(5) DSP system programmer.(6) Shop personnel.(7) Field personnel.

d. This submittal must justify in the judgment of the Owner’s Representative that theContractor has the capability to manage and install a project of this size and scopeand that he is capable of the necessary business and technical arrangements for thisinstallation and the pursuant warranty service.

5. Structural Engineer Qualifications:a. Structural Engineer: A Professional Engineer registered and engaged in regular

practice in the Project State.6. Manufacturer Qualifications:

a. A prime system manufacturer who maintains or sponsors a service center capable ofproviding training, parts, and emergency maintenance and repairs at Project site witha 24-hour maximum response time.




b. Minimum of 10 years continuous experience in the design and manufacture ofaudio-video, control, network and optical equipment.

c. ISO 9001 quality certification for a period of 5-years or longer.7. Substitutions:

a. Model numbers and manufacturers included in this Section are listed as a standard offunction, performance and quality.

b. Prior to acceptance of a substitute product, demonstrate equivalency by direct A/Bcomparison to the Owners Representative.

8. Source Limitations:a. Obtain each category of audio-video systems through one source from a single

manufacturer. Obtain each piece of equipment as a complete unit, includingnecessary mounting hardware and accessories.

9. Electrical, electronic and optical equipment:a. Products of firms regularly engaged in the manufacture of electrical, electronic or

optical equipment. Provide latest model or type offered which meets the applicablespecifications at the time of the submittal.

10. Materials:a. Provide only new materials and products.b. Do not use discontinued items replaced by newer models or versions.c. If an item specified in Part 2 of this section has been discontinued, submit the

manufacturer’s direct replacement for review and approval by the Owner’srepresentative.

1.07 DELIVERY, STORAGE AND HANDLINGA. Deliver portable audio and visual system components, equipment, materials, and accessories to

project site in original, unopened packages and store them in a fully enclosed, conditionedspace where they will be protected against damage from moisture, humidity, temperatureextremes, direct sunlight, surface contamination, and other causes.

B. Handle components, equipment, materials and accessories carefully to avoid damaging units inany way.

C. Do not deliver the audio-video system assemblies until the building is enclosed and otherconstruction within spaces where the audio-video system assemblies will be installed iscomplete and ready for installation.

1.08 COORDINATIONA. Coordinate arrangement of the audio-video system assemblies with adjacent construction, and

with components occupying ceiling space, including structural members, pipes, air-distributioncomponents, raceways, cable trays, recessed lighting fixtures, ceiling framing, light fixtures,HVAC equipment, fire-suppression system, and partitions.

B. Refer to Electrical Drawings for service voltage, power feed. Refer to Category AVS Drawingsfor control and interlock wiring for equipment specified under this Section.

C. Coordinate layout and installation of audio-video system with adjacent construction, includingceiling framing, light fixtures, HVAC equipment, fire-suppression system, and partitions.

1.09 PROJECT SITE CONDITIONSA. Environment Requirements.

1. The spaces where audio-video system assemblies are installed shall meet the followingrequirements:a. Free from dust generated from construction.b. The room temperature shall be within the specified operating temperature

recommended by manufacturer.




1.10 SEQUENCINGA. General:

1. Allow adequate time for corrections to be made after Inspections to maintain the ProjectSchedule.

2. Allow adequate time for corrections to be made after Submittals to maintain the ProjectSchedule.

3. Sequence the Project Submittals and Inspection Requests as follows:a. Qualifications Submittal.b. Shop Drawings and Product Data.c. Shop Test Report.d. Shop Observation Inspection Request.e. Shop Observation Inspection.f. Substantial Completion Inspection Request.g. Substantial Completion Inspection.h. Field Test Report.i. Operations and Service Manual and Record Drawing.j. Final Inspection Request.k. Final Inspection.l. Training Request.m. Training.n. Warranties.

1.11 WARRANTYA. General Warranty: Special warranty specified in this Article shall not deprive Owner of other

rights that the Owner may have under other provisions of the Contract Documents and shall bein addition to, and run concurrent with, other warranties made by Contractor under requirementsof the Contract Documents.

B. Special Warranty: Written warranty, executed by manufacturer agreeing to repair or replacecomponents of audio-video system that fail in materials or workmanship within specifiedwarranty period.1. Warranty Period: Two years from date of the Final Inspection and Acceptance.2. Response Time:

a. Provide telephone technical support on-call from 7:00a.m. to 12:00a.m. 7 days aweek. Maximum response time response time 30 minutes.

b. Provide on-site technical warranty service, with 48-hours of notification.3. The Warranty Period will begin when all of the documented Substantial Completion

Inspection Deficiencies have been corrected to the satisfaction of the Owner and theOwner’s Representative.

1.12 MAINTENANCEA. Maintenance Service:

1. Provide one service call to the project site to check and adjust the AV systems threemonths after Final Acceptance.

2. Provide one service call to the project site to check and adjust the AV systems six monthsafter Final Acceptance.

3. Maintain and monitor the all controllable devices remotely.4. Provide a Maintenance Service Agreement Contract to maintain the AV system after the

Warranty Period has expired as part of the Bid Documents. The Service Agreementscope of work includes maintenance required to the AV system so that it functions exactlyas it did at the time of final acceptance.




PART 2 - PRODUCTS2.01 SOURCE EQUIPMENT

A. Disk Player1. Network CD/Media Player (CD-DM-DN-700C):

a. Acceptable: D&M Pro DN-700C + D&M RC-F400s or equal (no known equal).2. Universal Multi-Disk Player3. 4K Ultra HD Blu-Ray Player (BR-SY-UBP-X1000ES):

a. Acceptable: Sony 4K Ultra HD Blu-ray Player UBP-X1000ES or equal.4. Professional Solid-State Audio Recorder

a. Audio Recorder (CD-DM-DN-700R)1) Acceptable: D&M Pro DN-700R + D&M RC-F400s

2.02 COMPUTERA. Workstation Computer (Computer)

1. Acceptable: Dell XPS 27 All-in-one cax2710w10hs4032. Acceptable: Blackmagic H.264 Recorder for 1080p HD-SDI3. Installed Software:

a. Audinate Dante Controllerb. BSS London Architectc. Crestron Toolboxd. Crestron DM Managemente. Crestron Fusionf. Blackmagic Video recording softwareg. Shure Wireless Workbenchh. Renkus Heinz RHAONi. ZeeVee Managerj. Yamaha Dante Virtual Sound Cardk. Yamaha DAW Nuendo Livel. Yamaha QL Editorm. Web management for Cisco switchesn. Web Management for Panasonic cameras

2.03 SOURCE EQUIPMENT - NETWORK INTERFACEA. Streaming Audio Player (SAP-SON-CONNECT):

1. Acceptable: Sonos Connect or equal (no known equal).B. Streaming Media Player (SMP-NVIDIA-SHIELD-PRO):

1. Acceptable: Nvidia Shield TV Pro or equal (no known equal).2.04 MICROPHONES - WIRELESS

A. Wireless Microphone System (WM-SH-ULXD4Q):1. Acceptable:

a. Receiver: Shure ULCD4Q or equal.b. Transmitter Shure QLXD1 + Sennheiser MKE-II Microphone

1) Quantity: Eighteenc. Transmitter Shure QLXD2/BETA87A

1) Quantity: EightB. Wireless Microphone System Antenna Splitter (ANT-SH-UA844+SWB):

1. Acceptable: Shure UA844+SWB2.05 DIGITAL MIXING CONSOLE

A. Digital Mixing Console (MIX-YA-QL5)1. Acceptable: Yamaha QL5 or equal.




2.06 INTERFACE CARDSA. I/O Card (CRD-YA-MY8-AE96S)

1. Acceptable: Yamaha MY8-AE96S2.07 DIGITAL AUDIO TRANSPORT

A. DANTE A to D Converter and Microphone Preamp (DAT-YA-RIO1608-D):1. Acceptable: Yamaha RIO 1608-D or equal (no known equal).

2.08 DIGITAL SIGNAL PROCESSORA. Digital Signal Processor (DSP-BSS-BLU-806):

1. Acceptable: BSS Soundweb London BLU-806, or equal.2. Features:

a. 4X Digital Signal Processorsb. DANTEc. Digital Audio Bus

B. Digital Signal Processor (DSP-BSS-BLU-326)1. Acceptable: BSS BLU-326 or equal

C. Interface Card1. Input Card (CRD-BSS-BLU-IN-ML)

a. Acceptable: BSS BLU-IN-ML2. Output Card (CRD-BSS-BLU-OUT-L)

a. Acceptable: BSS BLU-OUT-LD. Remote Control Interface

1. Flush-mount programmable control panel (CPL-BSS-BLU-10)a. Acceptable: BSS BLU-10 or equal.

2.09 DIGITAL AUDIO WORD CLOCKA. Master Word Clock (CLK-APG-BIGBEN)

1. Acceptable: Apogee Big Ben2.10 SURROUND PROCESSOR

A. Surround Decoder1. Surround Processor (REC-YA-CX-A5100):

a. Acceptable: Yamaha CX-A5100 or equal.2.11 AUDIO AMPLIFIER

A. Power Amplifier1. Power Amplifier (AMP-QC-ISA300TI):

a. Acceptable: QSC ISA 300TI or equal.2. Power Amplifier (AMP-QC-CX404)

a. Acceptable: QSC CX4043. Power Amplifier (AMP-LG-D20:4L)

a. Acceptable: Lab Gruppen D20:4L2.12 LOUDSPEAKERS

A. Loudspeaker - Reinforcement1. Loudspeaker (SPK-RH-PN81R-9060)

a. Acceptable: Renkus-Heinz PN81R-9060 or equal2. Loudspeaker (SPK-RH-TA82-RD)

a. Acceptable: Renkus-Heinz TA82-RD or equal3. Loudspeakers (SPK-RH-VA101i-(horn angle listed below)):

a. Acceptable:1) Speaker: Renkus Heinz Varia VA101i-15/6-R or equal.




2) Speaker: Renkus Heinz Varia VA101i-22/69-R or equal.3) Speaker: Renkus Heinz Varia VA101i-22/912-R or equal.4) Speaker: Renkus Heinz Varia VA101i-22/120-R or equal.

4. Rigging Hardware:a. Renkus Heinz RHANG Head-Frame and rigging hardware or equal.

5. Loudspeaker - Ceilinga. 6.5” Ceiling Speaker (SPK-MA-C6.8T)

1) Acceptable: Martin Audio C6.8Tb. Loudspeakers Sub Woofer (SPK-RH-BPS12-2):

1) Acceptable:(a) Speaker: Renkus Heinz BPS12-2 or equal.

2.13 ASSISTIVE LISTENINGA. Comply with 2016 CBC 11B-219 & 706B. Stationary RF Transmitter (ADA-LS-LT-800-072-01)

1. Acceptable: Listen LT800-072-01 with Rack Kit and Antenna and Signage Kit or equal.2.14 CAMERA

A. PTZ Camera1. PTZ Camera (CAM- PA-AW-HE130):

a. Acceptable: Panasonic PA-AW-HE130 or equal.2. Camera -Analog Color Fixed

a. Analog Color Fixed Camera (CAM-SY-SNC-VB630):1) Acceptable: Sony SNC-VB630 with lens or equal.

2.15 CAMERA CONTROLLERA. Camera Controller for PTZ camera (CCU-PA-AW-RP50)

1. Acceptable: Panasonic AW-RP50.2.16 DIGITAL VIDEO CONVERTER

A. Digital Video Converter (DVC-BM-HD-ANALOG-SDI)1. Acceptable: Black Magic HD-ANALOG-SDI2. Digital Video Converter (DVC-BM-CONVMCAUDS2)

a. Acceptable: Black Magic CONVMCAUDS23. Digital Video Converter (DVC-AJA-HI5PLUS)

a. Acceptable: AJA HI5PLUS2.17 HD-SDI VIDEO - DISTRIBUTION AMPLIFIER

A. 1 X 6 HD-SDI Distribution Amplifier: (VDA-BM-HD-SDI-DA):1. Acceptable: Black Magic HD-SDI-DA or equal.

2.18 REMOTE CONTROL SYSTEMA. Mainframe

1. Control System Mainframe: (CNL-CN-CP3N)a. Acceptable: Crestron CP3N

2. Wired Touch Panela. 5” Touch Screen (TP-CN-TSW-560)

1) Acceptable: Crestron TSW-560 or equal2) Features:

(a) Color: Black3. 15.6” Touch Screen (TP-CN-TS-1542)

a. Acceptable: Crestron TS-1542 or equalb. Features:

1) Color: Black




4. Wireless Touch Panela. Control Screen (RC-IPAD-PRO10)

1) Acceptable: Apple 10“ iPad Pro or equal2.19 DIGITAL AV SYSTEM

A. Matrix Switchers1. 16X16 DigitalMedia Switcher (SW-CN-DM-MD16X16-RPS):

a. Acceptable: Crestron DM-MD16X16-RPS or equal.b. 16 Port DigitalMedia Power over DM.

1) Acceptable: Crestron CEN-SWPOE-16 or equal.2. Switcher Input Cards

a. HDMI Input Card (CRD-CN-DMC-4K-HD-HDCP2):1) Acceptable: Crestron DMC-4K-HD-HDCP2 or equal.

b. HS-SDI Input Card (CRD-CN-DMC-SDI):1) Acceptable: Crestron DMC-SDI or equal.

c. DigitalMedia 8G+ Input Card (CRD-CN-DMC-4K-C-HDCP2):1) Acceptable: Crestron DMC-4K-C-HDCP2 or equal

3. DigitalMedia Switcher Output Cardsa. DigitalMedia Output Card (CRD-CN-DMC-4K-CO-HD-HDCP2):

1) Acceptable: Crestron DMC-4K-CO-HD-HDCP2 or equal.2) Features:

(a) 2 DM-C Outputs(b) 1 Parallel HDMI Output

b. DigitalMedia Output Card (CRD-CN-DMC-STRO):1) Acceptable: Crestron DMC-STRO or equal.

4. Digital AV System - Transmittersa. DigitalMedia 8G+ Wall Plate Transmitter (TX-CN-DM-TX1-4K-C-1G):

1) Acceptable: Crestron DM-TX1-4K-C-1G or equal.2) Features:

(a) Color: Blackb. DigitalMedia 8G+ Wall Plate Transmitter (TX-CN-DM-TX-200-C-2G):

1) Acceptable: Crestron DM-TX-200-C-2G or equal.2) Features:

(a) Color: Blackc. DigitalMedia 8G+ Transmitter (TX-CN-DM-TX-401-C)

1) Acceptable: Crestron DM-TX-401-C or equal2) Features:

(a) Color: Black5. Digital AV System - Receivers & Controllers

a. DigitalMedia 8G+ Wall Plate Receiver (RX-CN-DM-RX1-4K-C-1G):1) Acceptable: Crestron DM-RX1-4K-C-1G or equal.

2.20 ETHERNET SWITCHA. 48 Port Ethernet Switch with PoE/PoE+ (ES-CI-WS-C2960X-48FPD-L):

1. Acceptable: Cisco WS-C2960X-48FPD-L or equal.2. 48 Port Ethernet Switch (ES-CI-WS-C2960X-48TD-L):

a. Acceptable: Cisco WS-C2960X-48TD-L or equal.3. 12 Port PoE Ethernet Switch (ES-CI-WS-C3750G-12S-S):

a. Acceptable: Cisco WS-C3750G-12S-S or equal.2.21 NETWORK ATTACHED STORAGE

A. Five Bay NAS Server (NAS-SY-DS1517+)1. Acceptable:




a. Synology DiskStation DS1517+b. Synology 8GB DDR38 GB RAM modules

1) Quantity: Two.c. Synology M2D17 Dual M.2 SATA SSD Card.

1) Quantity: One.d. Cash Drive: Samsung 512GB 970 PRO NVMe M.2 Internal SSD Cash Drives

1) Quantity: Two.e. Data Storage Hard Drive

1) Quantity: Fivef. Configuration:

1) Synology four disk SHR RAID disk array.2) One hot spare disk.3) Configure Audio, Video, Photo and Plex video server service.

B. Data Storage Hard Drive1. 6 Terabyte Hard Drive

a. Acceptable: Western Digital Red Pro NAS WD6002FFBX2.22 DATA ROUTER

A. Router + Wireless Access Point (RT-SY-RT2600AC)1. Acceptable:2. Synology RT2600ac3. SanDisk Ultra Fit 32GB USB 3.0 Flash Drive - SDCZ43-032G-GAM4

2.23 PRODUCTION COMMUNICATIONSA. Main Stations

1. Two Channel Intercom Master Station (PC-CC-MS-702):a. Acceptable: Clear-Com MS-702 Clear-Com with GM-18 or equal.

2. Page Stationsa. Intercom Speaker Station (PC-CC-KB-701):

1) Acceptable: Clear-Com KB-701 or equal.2.24 RF - DISTRIBUTION

A. General:1. Functional Description: Broad-band RF amplifier and splitters to allow cable TV signal to

be selectively patched to co-ax lines for distribution within the building Equipment toinclude the following components by a single vendor:

2. Installation: Submit block diagram, bill of materials and cut sheets for approval.3. Video Modulator (MOD-ZV-P820):

a. Acceptable: ZeeVee ZvPro 820 HD Video Distribution QAM Modulator over COAX1080p or equal.

2.25 VIDEO PROJECTORA. Video Projector (VP-DP-118-053)

1. Acceptable: Digital Projection M Vision Laser 18K 118-053 or equal2. Acceptable: Digital Projection 1.50 - 2.00:1 Zoom lens 118-578, or as required by field

measurement verification2.26 VIDEO MONITOR

A. Video Monitor (LCD-NC-V423-AVT)1. Acceptable: NEC V423-AVT or equal2. Video Monitor (MONITOR)

a. Acceptable: Dell Ultrasharp 24” U2417H or equalb. Specification: 1920X1080 native resolution, HDMI/HDCP input.




2.27 EQUIPMENT ENCLOSURESA. Stationary Gangable Equipment Enclosures:

1. Acceptable:a. 44 Space: Middle Atlantic WRK-44-27 or equal.b. Quantity:

1) Equipment Enclosure: As shown on the Drawings.2) Side panel: 1 pair for each side by side assembly provided.3) Top panel: 1 for each equipment enclosure provided.4) Rear door: 1 for each equipment enclosure provided.5) Plexi Front door: 1 for each equipment enclosure provided.6) Mid rails: 1 pair for each equipment enclosure provided.

2. Pivoting Wall Mounted Equipment Enclosure:a. Acceptable:

1) 40 Space - 26” Deep: Middle Atlantic SR-40-28 or equal.2.28 EQUIPMENT ENCLOSURE ASSEMBLY PARTS

A. Blank Panels:1. Acceptable:

a. 1 Space: Middle Atlantic EB1 or equal.b. 2 Space Middle Atlantic EB2 or equal.c. 3 Space Middle Atlantic EB3 or equal.d. 4 Space Middle Atlantic EB4 or equal.e. 5 Space Middle Atlantic EB5 or equal.f. 6 Space Middle Atlantic EB6 or equal.g. Features:

1) Steel flange2) 19-inch standard EIA width

h. Specification:1) Thickness: 11 Gauge2) Space Height

(a) 1 Space(b) 2 Space(c) 3 Space(d) 4 Space(e) 5 Space(f) 6 Space

B. Vent Panels:1. Acceptable:

a. 1 Space: Middle Atlantic VT1, Lowell L5-191 or equal.b. 2 Space Middle Atlantic VT2, Lowell L5-193 or equal.c. 3 Space Middle Atlantic VT3, Lowell L5-195 or equal.d. 4 Space Middle Atlantic VT4, Lowell L5-197 or equal.

2. Features:a. 16 Ga. perforated steel.b. Black power coat finishc. 19-inch standard EIA width

3. Specification:a. Thickness: 11 Gaugeb. Open Area: 65%c. Space Height

1) 1 Space2) 2 Space




3) 3 Space4) 4 Space

C. Equipment Enclosure Rack Kit:1. Acceptable: Custom by Middle Atlantic, Lowell or manufactures optional equipment

enclosure kit.2. Features:

a. 1/6-inch anodized brushed aluminum finishb. Custom manufactured for each piece of equipmentc. 19-inch standard EIA width

3. Quantity: 1 for each non-standard 19-inch EIA piece of equipment4. Left Equipment Enclosure Screw Hardware:

a. Acceptable: Middle Atlantic HTX, Lowell RSV or equal..b. Features:

1) High security star post design.2) Black oxide finish.

c. Specification:1) Size: 10-32

d. Quantity: One for every left equipment enclosure ear mounting position.5. Right Equipment Enclosure Screw Hardware:

a. Acceptable: Middle Atlantic HS, Lowell RSR or equal..b. Features:

1) Tamper resistant security square drive.2) Black oxide finish.

c. Specification:1) Size: 10-32

d. Quantity: One for every right equipment enclosure ear mounting position.D. Vertical Cable Management Lace Bar

1. Acceptable: Middle Atlantic LACE, Lowell CLB77 or equal.2. Features:

a. Highly perforated steel lacer bar mounts vertically to equipment enclosure railbrackets and provides ample holes for cable ties.

3. Specification:a. Height: 44 space length can be cut down to smaller sizes.b. Width: 2:

4. Quantity: 2 for every equipment enclosure provided minimum.E. Horizontal Cable Management Lace Bar

1. Acceptable: Middle Atlantic LBP-1R4, Lowell LCRS4 - or equal.2. Features:

a. Horizontally cable management.b. Made from 1/4-inch diameter flattened rod.c. Provides convenient cable tie points.d. 4-inch offset.e. Black powder coat finish.

3. Quantity: 1 for every piece equipment provided.F. Freestanding Equipment Enclosure Cooling System:

1. Acceptable:a. Fan: Middle Atlantic QFAN with fan guard or equal.b. Control: Middle Atlantic FC-4 or FC-4-1C or equal.

2. Features:a. 4” Fan.b. Thermostatically controlled fan.




3. Specification:a. CFM: 50.b. Noise: Less than 30 dB.

4. Quantity:a. One cooling system for each fixed equipment rack enclosure provided.b. Four fans for each fixed equipment rack enclosure provided.

G. Equipment Enclosure Light:1. Acceptable: Middle Atlantic WL-60 or equal.2. Features:

a. Magnetic work light.3. Specification:

a. Power: 27 Watt fluorescent bulb.4. Quantity: One for every equipment enclosure provided.

H. Equipment Labels:1. Features:

a. Custom fabricated by Contractor.b. Descriptive equipment labels.c. Character Height: 1/8” minimum.

2. Acceptable:a. Engraved black/white laminated plastic labels.b. Stick-on strip labels such as those from Dymo or Brother are not acceptable.

3. Quantity:a. One for every piece of equipment provided.b. One for every connector provided.c. One for every user control function provided.d. One for every equipment rack provided.

2.29 POWER SEQUENCE AND AC POWER DISTRIBUTION:A. Modular AC Power Distribution and Sequencing System for Stationary Equipment Enclosures

from 24-Space Height to 44-Space Height:1. Acceptable:

a. 3 Module Raceway: Middle Atlantic MPR3, or equal.b. 6 Module Raceway: Middle Atlantic MPR6 or equal.c. 9 Module Raceway: Middle Atlantic MPR9 or equal.d. 15A. Module: Middle Atlantic RLM 15IG, or equal.e. 20A. Module: Middle Atlantic RLM 20IG, or equal. or equal.f. Sequencing Controller: Middle Atlantic USC-6R, or equal.g. Jumpers: Middle Atlantic J and T series or equal.h. Features:

1) General:(a) UL Listed(b) Switchable power modules in vertical power raceways.(c) 15 Amp and 20 Amp modules.(d) Power Modules:

(1) Contact closure and led power indicator.(2) Available in three sizes to accommodate 3, 6, or 9 duplex power

modules.(3) Constructed of 18-gauge min-spangle galvanized steel.(4) Electrical knockouts and integral J-box with removable cover(5) Power cable lacing points along both sides.

(e) Sequencing Controller:




(1) Provides 6-step sequencing control to AC power distribution systemwith switch closure or 12 Volt DC.

(2) Sequencing can be initiated locally with a front panel switch, as well asremotely via a momentary dry-contact closure key-switch.

(3) Interval delay selector of 1, 3, or 6 seconds between sequence steps.(4) Up to three USC-6R units to be interconnected to operate as a single

18 step unit.(5) LED status indicators.(6) Durable black powder coat finish.

(f) Key-switch:(1) Provides remote up/down sequence initiation via a secure keyswitch.(2) Status LED indicators provided.

i. Specification:1) Ground: Isolated.2) Rated Power: 15A., 20A and 30A. Modules.

j. Quantity:1) One power sequencing system for each stationary equipment rack provided.2) Jumpers and modular power outlets as required.

2. High Density Modular AC Power Distribution System for Stationary Equipment Enclosuresfrom 24-Space Height to 44-Space Height:a. Acceptable:

1) Power Strip: Middle Atlantic PDW Series Multi-Circuit, High Capacity PowerDistribution.

2) May be used in conjunction with Middle Atlantic Power Sequencing system.b. Features:

1) General:(a) UL Listed(b) Custom Configured from the manufacturer with 15 Amp,20 Amp and 30

Amp Outlets.c. Specification:

1) Ground: Isolated.2) Rated Power: 15A., 20A and 30A circuits.

d. Quantity:1) One power outlet for each piece of equipment required.

3. Rack Mount AC Power Distribution and Sequencing System for Equipment Enclosuresfrom 6-Space Height to 24-Space Height:a. Acceptable:

1) Middle Atlantic PDS-615R or equal.2) Middle Atlantic PDS-620R or equal.3) Middle Atlantic PDS-2X315R or equal.

b. Features:1) General:

(a) UL Listed(b) Switchable power modules in horizontal rack mount power distribution.(c) 15 Amp and 20 Amp models.(d) Sequencing Controller:

(1) Provides 6-step sequencing control to AC power distribution systemwith switch closure or 12 Volt DC.

(2) Sequencing can be initiated locally with a front panel switch, as well asremotely via a momentary dry-contact closure key-switch.

(3) Interval delay selector of 1, 3, or 6 seconds between sequence steps.(4) LED status indicators.(5) Durable black powder coat finish.




c. Specification:1) Rated Power: 15A. and 20A.

d. Quantity:1) One power sequencing system for each equipment rack provided.

4. Rack Mount AC Power Distribution System for Equipment Enclosures from 6-SpaceHeight to 24-Space Height:a. Acceptable:

1) Middle Atlantic PDC-915R or equal.b. Features:

1) General:(a) UL Listed(b) Switchable power modules in rack mounted enclosure.(c) Built-in 2-stage surge suppression with notification.(d) Settings for momentary or maintained control style, normally opened or

normally closed.c. Specification:

1) Rated Power: 15A. and 20A.d. Quantity:

1) One power distribution system power outlet for each piece of equipmentprovided.

2.30 UNINTERRUPTABLE POWER - UPS:A. Uninterruptable Power - 280W / 450 VA:

1. Acceptable: APC SC450RM1U or equal.2. Uninterruptable Power 1425W 1500 VA:

a. Acceptable: APC SUM1500RMXL2U or equal.3. Uninterruptable Power - 2850W / 3000 VA:

a. Acceptable: APC SMX3000LV or equal.2.31 EQUIPMENT ENCLOSURE CABLE TERMINATION

A. Cable Terminal Block System:1. Features:

a. Universal rail mounting standard screw clamp.b. Versatile feed through terminals.c. Easy mounting and dismounting from the DIN Rail.d. Multiple connection configurations:e. Specification:

1) Color:(a) Match cable conductor shield.(b) Red, Blue, Black, Orange, Green, White, Yellow.(c) Wire Gage: As required(d) Configuration: As required.

f. Acceptable:1) Alltech C Series equal (no known equal).

g. Quantity: One terminal connection for every cable entering or leaving the equipmentenclosure.

2. Terminal Block:a. Features:

1) Barrier screw lug.2) Accept up to #10 cable.

b. Acceptable: Beau, Kukla or approved equal.c. Quantity: Use as required.




2.32 VOLUME CONTROL:A. 100 Watt Manual Volume Control (VC-LO100), (VC-AT-AT100):

1. Acceptable: Lowell 100LVC, Atlas/Soundolier AT100 or equal.2.33 LAMPS

A. Reading Lamps, Control Console, Mixing Console:1. Acceptable: LittlLite 18G-HI, DM dimmer and Q5 bulb or equal.2. Features:

a. 5 Watt dimmable, high-intensity lamps on 18-inch flexible stemb. Attaches via BNC connectorc. Located on panels in console end equipment enclosure as shown on drawingsd. Provide 100% spare lamps

2.34 CABLE - INSTALLED IN CONDUITA. General:

1. The conduit shown on the EAV Category Drawings is sized for the first cable product listedin the Cable Installed in Conduit section. In the event that the Contractor selects one ofthe alternate cables listed the Contractor is solely responsible for changes to the conduit.

2. Audio Microphone:a. Acceptable: Belden 8761 or equal.b. Unacceptable:

1) Belden 8451, Belden 9451, West Penn (x)454.c. Features:

1) Low capacitance.2) CM rated.3) Tinned copper.4) Polyethylene insulated.

d. Specification:1) Conductor Configuration: Twisted shielded pair.2) Wire Gauge: 22.3) Nominal Capacitance: 24 pF/ft.4) Nominal Outside Diameter: .175-inch.5) Shield Coverage: 100%.6) Stranded Conductors: Stranded 7x30.

3. Audio Line:a. Acceptable: Belden 8761 or equal.b. Unacceptable:

1) Belden 8451, Belden 9451, West Penn (x)454c. Features:


d. Specification:1) Conductor Configuration: Twisted shielded pair.2) Wire Gauge: 22.3) Nominal Capacitance: 24 pF/ft.4) Nominal Outside Diameter: .175-inch.5) Shield Coverage: 100%.6) Stranded Conductors: Stranded 7x30.

4. AES/EBU Single Channel Audio Cable:




a. Acceptable: Belden 1801B, Liberty Wire and Cable 24-1P-PLN-DIG-AUDIO, CanareDA202 AES/EBU Digital Audio Cable.

b. Features:1) Tinned copper conductors.2) Foam FEP Teflon insulation.3) Flamarrest jacket.4) 24 AWG tinned copper drain wire.5) 100% Beldfoil shield.

c. Specifications:1) Conductor:

(a) Number of Pairs: 1.(b) Total Number of Conductors: 2.(c) AWG: 24.(d) Stranding: 7x32.(e) Conductor Diameter: .024 inches.(f) Conductor Material: TC - Tinned Copper.(g) Insulation:

(1) Insulation Material Trade Name: Teflon.(2) Insulation Material: FFEP - Foam Fluorinated Ethylene Propylene.(3) Insulation Diameter: .066 inches.

(h) Inner Shield: 1.(1) Color: Red & Black.

(i) Outer Shield:(1) Outer Shield Material Trade Name: Beldfoil.(2) Outer Shield Type: Tape.(3) Outer Shield Material: Aluminum Foil-Polyester Tape.(4) Outer Shield % Coverage: 100 %.

(j) Outer Shield Drain Wire:(1) Outer Shield Drain Wire AWG: 24.(2) Outer Shield Drain Wire Stranding: 7x32.(3) Outer Shield Drain Wire Conductor Material: TC - Tinned Copper.

(k) Outer Jacket:(1) Outer Jacket Material Trade Name: Flamarrest.(2) Outer Jacket Material: LS PVC - Low Smoke Polyvinyl Chloride.

(l) Overall Nominal Diameter: .165 inches.(m) Mechanical Characteristics:

(1) Operating Temperature Range: -20°C To +75°C.(2) UL Temperature Rating: 75°C.(3) Bulk Cable Weight: 13 lbs/1000 feet.(4) Max. Recommended Pulling Tension: 16.5 lbs.(5) Min. Bend Radius (Install): 1.75 inches.

(n) Applicable Standards:(1) NEC/(UL) Specification CMP.(2) CEC/C(UL) Specification CMP.(3) Other Specification AES/EBU.

5. Video Analog Composite RG 59: - > 500-foot Length Run:a. Acceptable: Belden 8281B or equal.b. Features:

1) CM rated.2) Precision video Coax.3) Double braided shield.4) Polyethylene jacket.




c. Specification:1) Conductor Configuration: Coaxial.2) Wire Gauge: 20.3) Nominal Capacitance: 20.5 pF/ft.4) Impedance: 75 Ohm.5) Shield Coverage: 98%.6) Conductor: Solid.7) Nominal Outside Diameter: .305-inch.

6. Video Analog Composite RG 59: - < 500-foot Length Run:a. Acceptable: Belden 1505A, Extron 22-145-03 or equal.b. Features:

1) CM rated.2) Precision video coax.3) Foil and braid shield.4) Polyethylene jacket.

c. Specification:1) Conductor Configuration: Coaxial.2) Wire Gauge: 20.3) Nominal Capacitance: 16.3 pF/ft.4) Impedance: 75 Ohm .5) Shield Coverage: 100%.6) Conductor: Solid.7) Nominal Outside Diameter: .235-inch.

7. Video Digital Composite RG 6: - < 300-foot Length Run:a. Acceptable: Belden 1694A, Extron 22-098-03 or equal.b. Features:

1) CM rated.2) Precision digital video coax.3) Foil and braid shield.4) Polyethylene jacket.


8. Low Loss RF Transmission Cable: - < 100-foot Length Run:a. Acceptable: Belden 7808A 240 or equal.b. Features:

1) Foam high-density polyethylene insulation.2) Tinned copper braid shield.3) Polyethylene jacket.

c. Specification:1) Conductor Configuration: Coax: 1.2) Wire Gauge: 15.3) Nominal Capacitance: 23.0 pF/ft.4) Impedance: 50 Ohm.5) Shield Coverage:

(a) Bonded DuoFilm: 100%.(b) Tinned Copper: 95%.




(c) Conductor: Solid(d) Nominal Outside Diameter: .240-inch

9. Low Loss RF Transmission Cable: - > 100-foot Length Run:a. Acceptable: Belden 7810A, or equal.b. Features:

1) Foam high-density polyethylene insulation.2) Tinned copper braid shield.3) Polyethylene jacket.

c. Specification:1) Conductor Configuration: Coax: 1.2) Wire Gauge: 10.3) Nominal Capacitance: 23.0 pF/ft.4) Impedance: 50 Ohm.5) Shield Coverage:

(a) Bonded DuoFilm: 100%.(b) Tinned Copper: 95%.(c) Conductor: Solid.(d) Nominal Outside Diameter: .403-inch.

10. Video Component RG 59/U:a. Acceptable:

1) RGB: Belden 7794A or equal.2) RGBHV: Belden 7796A or equal.

b. Features:1) CM rated.2) Precision video coax.3) Foil and braid shield.4) Polyethylene jacket.

c. Specification:1) Conductor Configuration: Coaxial.2) Wire Gauge: 20.3) Nominal Capacitance: 16.3 pF/ft.4) Impedance: 75 Ohm.5) Shield Coverage: 100%.6) Conductor: Solid.7) Nominal Outside Diameter:

(a) RGB: .631-inch.(b) RGBHV: .790-inch.

11. 35 Volt Loudspeaker:a. Acceptable: THHN type #10, Canare 4S11 or equal.

1) Features:(a) Standard electrical cable.(b) CM Rated.(c) Specification:

(1) Conductor Configuration: Individual pair.(2) Wire Gauge: 10.(3) Shield Coverage: Un-shielded.(4) Conductor: Stranded copper.(5) Nominal Outside Diameter: .685-inch.

b. Acceptable: Belden YR442331) Features:

(a) Standard electrical cable.(b) UL Type CL2R - Audio Only




(c) Specification:(1) Conductor Configuration: Individual pair.(2) Wire Gauge: 10.(3) Shield Coverage: Un-shielded.(4) Conductor: Stranded copper.(5) Nominal Outside Diameter: .446-inch.

c. Acceptable: Belden YR468891) Features:

(a) Standard electrical cable.(b) UL Type CL2R - Audio Only(c) Specification:

(1) Conductor Configuration: Individual pair.(2) Wire Gauge: 10.(3) Shield Coverage: Un-shielded.(4) Conductor: Stranded copper.(5) Nominal Outside Diameter: .446-inch.

12. 70 Volt Loudspeaker:a. Acceptable: Belden 8473, Liberty 16-2-GRY or Extron 22-152-03.b. Features:

1) CM rated.2) PVC jacket.

c. Specification:1) Conductor Configuration: Unshielded twisted pair.2) Wire Gauge: 14.3) Shield Coverage: Un-shielded.4) Conductor: Stranded 42x30.5) Nominal Outside Diameter: .340-inch.

13. Radio Frequency RG-58:a. Acceptable: Belden 8240 or equal.b. Features:

1) CM rated.2) Braided shield.3) PVC jacket.


14. Digital Control:a. Acceptable: Belden 8102 or equal.b. Features:

1) CM rated.2) Braided shield.3) Low capacitance.4) PVC jacket.

c. Specification:1) Conductor Configuration: 2 shielded twisted pair.2) Wire Gauge: 24.3) Nominal Capacitance: 12.5 pF/ft.




4) Impedance: 100 Ohm .5) Shield Coverage: 65%.6) Conductor: Stranded 7x32.7) Nominal Outside Diameter: .270-inch.

15. DC Control:a. Acceptable: Belden 8461 or equal.b. Features:

1) CM rated.2) High conductivity.3) PVC jacket.

c. Specification:1) Conductor Configuration: one unshielded twisted pair.2) Wire Gauge: 18.3) Shield Coverage: 0%.4) Conductor: Stranded 7x26.5) Nominal Outside Diameter: .234-inch.

16. Crestron Control (Crestnet)a. Acceptable: Crestron Crestnet-NP-TL

17. DC Power:a. Acceptable: Belden 8477 or equal.b. Features:

1) CM rated.2) High conductivity.3) PVC jacket.

c. Specification:1) Conductor Configuration: one unshielded twisted pair.2) Wire Gauge: 12.3) Shield Coverage: 0%.4) Conductor: Stranded 65x30.5) Nominal Outside Diameter: .386-inch.

18. Video Teleconferencinga. Video Teleconferencing Codec (VT-PLY-HDX-8000)

1) Acceptable: Polycom HDX-8000 or equalb. Video Teleconferencing Codec (VT-PLY-HDX-9000)

1) Acceptable: Polycom HDX-9000 or equalc. Video Teleconferencing Codec (VT-PLY-EE-IV-HD)

1) Acceptable: Polycom EE-IV-HD or equald. Video Teleconferencing Codec (VT-PLY-HDX-MIC-ARRAY)

1) Acceptable: Polycom HDX-MIC-ARRAY or equale. Video Teleconferencing Codec (VT-TP-SX80-CODEC)

1) Acceptable: Cisco SX80-CODEC or equalf. Video Teleconferencing Codec (VT-TP-SX80-CODEC-C60)

1) Acceptable: Cisco SX80-CODEC-C60 or equal19. Production Communications:

a. Acceptable:1) Installed in conduit: Belden 8719 equal (no known equal).

b. Features:1) CM rated.2) Tinned copper.3) PVC jacket.

c. Specification:1) Conductor Configuration: Two twisted shielded pair.




2) Wire Gauge: 16.3) Drain Wire Gauge: 184) Stranded Conductors: Stranded 19x29.

20. Optical Fiber:a. Acceptable: Belden MTBP604 or equal.b. Features:

1) Fiber, 4 fibers.2) FA - Flamarrest jacket.3) FGE/Aramid Strength Member.4) 62.5/125/900 Micron Fiber Type.5) UL/NEC/CEC Listing: OFNP.6) PVC jacket.

c. Specification:1) Flame Tests: Passes IEEE 383, CSA FT6, and UL 910 Flame Test.2) 50 micron and single mode fiber.3) Nominal Outside Diameter: 293-inch.

21. Data:a. Acceptable: Belden 10GX12 0051000 or equal.b. Specification:

1) Category 6A.2) Color: Green

2.35 CABLE - INSTALLED IN PLENUM SPACEA. Audio Microphone:

1. Acceptable: Belden 88761 or equal.2. Unacceptable:

a. Belden 8451, Belden 9451, West Penn (x)454.b. Features:


c. Specification:1) Conductor Configuration: Twisted shielded pair.2) Wire Gauge: 22.3) Nominal Capacitance: 24 pF/ft.4) Nominal Outside Diameter: .175-inch.5) Shield Coverage: 100%.6) Stranded Conductors: Stranded 7x30.

3. Audio Line:a. Acceptable: Belden 88761 or equal.b. Unacceptable:

1) Belden 8451, Belden 9451, West Penn (x)454c. Features:


d. Specification:1) Conductor Configuration: Twisted shielded pair.2) Wire Gauge: 22.3) Nominal Capacitance: 24 pF/ft.4) Nominal Outside Diameter: .175-inch.




5) Shield Coverage: 100%.6) Stranded Conductors: Stranded 7x30.

4. Video Analog Composite RG 59: - > 500-foot Length Run:a. Acceptable: Belden 88281 or equal.b. Features:

1) CM rated.2) Precision video Coax.3) Double braided shield.4) Polyethylene jacket.


5. Video Analog Composite RG 59: - < 500-foot Length Run:a. Acceptable: Belden 1506A, Extron 22-146-03 or equal.b. Features:



6. Video Digital Composite RG 6: - < 300-foot Length Run:a. Acceptable: Belden 1695A, Extron 22-164-03 or equal.b. Features:

1) CM rated.2) Precision digital video coax.3) Foil and braid shield.4) Polyethylene jacket.


7. Data:a. Acceptable: Belden 10GX13 0051000 or equal.b. Specification:

1) Category 6A.2) Color: Green




8. Crestron Control (Crestnet)a. Acceptable: Crestron Crestnet-P-TL

9. Crestron Digital Media:a. Acceptable:

1) Crestron DM-CBL-P or equal.2) Crestron DM-CBL-D-P or equal.3) Crestron DM-CBL-8G-P or equal.4) Crestron CRESFIBER-P or equal.5) Crestron CRESFIBER-DUAL-SC-P or equal.

2.36 CABLE - NOT INSTALLED IN CONDUITA. Audio Microphone:

1. Acceptable: Belden 8484, Liberty Wire and Cable 24-2P-STAR or Canare L-4E6S.2. Features:

a. Low capacitance.b. Polyethylene insulated.c. Silver Plated High Strength Copper Alloy conductors.d. Polypropylene insulation.e. Braided shield.f. Flexible Polyvinyl Chloride jacket.g. High Conductivity Copper.h. Low Impedance.i. Specification:

1) Conductor Configuration: 4 conductors quad shielded.2) Wire Gauge: 20.3) Nominal Capacitance: 49 pF/ft.4) Nominal Outside Diameter: .252-inch.5) Shield Coverage: 78%.6) Stranded Conductors: stranded (19x32).

3. Audio Line:a. Acceptable: Belden 8484, Liberty Wire and Cable 24-2P-STAR or Canare L-4E6S.b. Features:

1) Low capacitance.2) Polyethylene insulated.3) Silver Plated High Strength Copper Alloy conductors.4) Polypropylene insulation.5) Braided shield.6) Flexible Polyvinyl Chloride jacket.7) High Conductivity Copper.8) Low Impedance

c. Specification:1) Conductor Configuration: 4 conductors quad shielded.2) Wire Gauge: 20.3) Nominal Capacitance: 49 pF/ft.4) Nominal Outside Diameter: .252-inch.5) Shield Coverage: 78%.6) Stranded Conductors: stranded (19x32).

4. Audio Digital - Single CAT5e:a. Acceptable: Gepco CT504HD or equal.

5. Audio Digital - Dual CAT5e:a. Acceptable: Gepco CTS2504HDX or equal.

6. Audio Digital - Quad CAT5e:a. Acceptable: Gepco CTS4504HDX or equal.




7. Audio Digital - Multi CAT6A Plenuma. Acceptable: Belden 10GX53F Plenum CAT6A or equal.

8. Audio Digital - Multi CAT6Aa. Acceptable: Belden 10GX53F CAT6A or equal.

9. Video Composite RG 59:a. Acceptable: Belden 1505A or equal.b. Features:


c. Specification:1) Conductor Configuration: Coaxial2) Wire Gauge: 203) Nominal Capacitance: 16.3 pF/ft.4) Impedance: 75 Ohm5) Shield Coverage: 100%6) Conductor: Solid7) Nominal Outside Diameter: .235-inch

10. Video Component RG 59:a. Acceptable:

1) RGB: Belden 7794A or equal.2) RGBHV: Belden 7798A, Liberty Wire and Cable RGB5C-20-CMR or equal.

b. Features:1) CM rated.2) Precision video coax.3) Foil and braid shield.4) Polyethylene jacket.

c. Specification:1) Conductor Configuration: Coaxial.2) Wire Gauge: 20.3) Nominal Capacitance: 16.3 pF/ft.4) Impedance: 75 Ohm.5) Shield Coverage: 100%.6) Conductor: Solid.7) Nominal Outside Diameter:

(a) RGB: .631-inch.(b) RGBS: .706-inch.(c) RGBHV: .790-inch.

11. 35 Volt Loudspeaker 2 Conductor:a. Acceptable: Belden 19201, Canare 4S11 or equal.b. Features:

1) SO-2.2) Neoprene jacket.

c. Specification:1) Conductor Configuration: Twisted pair.2) Wire Gauge: 12.3) Shield Coverage: Un-shielded.4) Conductor: Stranded copper (65x30).5) Nominal Outside Diameter: .610-inch.

12. 35 Volt Loudspeaker 4 Conductor:a. Acceptable: Belden 19216 or equal.




b. Features:1) SO-4.2) Neoprene jacket.

c. Specification:1) Conductor Configuration: Two twisted pairs.2) Wire Gauge: 12.3) Shield Coverage: Un-shielded.4) Conductor: Stranded copper (65x30).5) Nominal Outside Diameter: .686-inch.

13. Radio Frequency RG-58:a. Acceptable: Belden 8240 Liberty Wire and Cable RG58-CMR-BLK or equal.b. Features:

1) CM rated.2) Braided shield.3) PVC jacket.


14. DC Power:a. Acceptable: Belden 19228 or equal.b. Features:

1) SO-2.2) Neoprene jacket.

c. Specification:1) Conductor Configuration: Twisted pair.2) Wire Gauge: 16.3) Shield Coverage: Un-shielded.4) Conductor: Stranded copper (26x30).5) Nominal Outside Diameter: .315-inch.

15. Production Communications:a. Acceptable:

1) Installed in conduit: Liberty Wire and Cable 24-2P-STAR or equal.b. Features:

1) Heavy duty construction.2) Tinned copper.3) Neoprene jacket.

c. Specification:1) Conductor Configuration: Twisted shielded pair.2) Wire Gauge: 18.3) Nominal Capacitance: 35 pF/ft.4) Shield Coverage: 85%.5) Shield: Braided.6) Conductors: Stranded 65x34.

16. Optical Fiber:a. Acceptable: Liberty Wire and Cable RGB3C-20-CMR 1FPIxx or equal.b. Features:

1) Fiber, 1 fiber.




2) FA - Flamarrest jacket.3) FGE/Aramid Strength Member.4) 62.5/125/900 Micron Fiber Type.5) UL/NEC/CEC Listing: OFNP.6) PVC jacket.

c. Specification:1) Flame Tests: Passes IEEE 383, CSA FT6, and UL 910 Flame Test.2) 50 micron and single mode fiber.3) Nominal Outside Diameter: 114-inch

2.37 CABLE - INSULATED FERRULESA. Low Voltage Single Cable Connectors:

1. Acceptable: BM Insulated Ferrules or equal.a. 22 AWG Cable: BM 00501.b. 20 AWG Cable: BM 00502.c. 18 AWG Cable: BM 00503.d. 16 AWG Cable: BM 005041.e. 14 AWG Cable: BM 005061.f. 12 AWG Cable: BM 005081.g. 10 AWG Cable: BM 00511.h. Features:

1) Single cable electrolytic copper tinned end-sleevesi. Quantity: One for every bare cable compression connection.

2.38 CABLE - LABELSA. Installed and Portable Cable Labels:

1. Acceptable:a. <0.313-inch cable diameter: Thomas and Betts WES2112 or equal.b. <0.468-inch cable diameter: Thomas and Betts WES12214 or equal.c. <0.875-inch cable diameter: Thomas and Betts WES12334 or equal.d. <1.5-inch cable diameter: Thomas and Betts WES2512 or equal.e. <2-inch cable diameter: Thomas and Betts WES2128 or equal.f. Features:

1) Printable markers.2) WSL self-laminating vinyl.3) Maximum protection against most common elements.

g. Specification:1) Thickness: 1 mil.2) Color: White with clear protective wrap.3) Label Designation Character:

(a) Print Method: Printed with a laser jet printer.(b) Character Height: 10 point minimum.(c) Font Type: Arial or Times New Roman.(d) Hand written labels are unacceptable.

h. Quantity: One at each end of every cable supplied minimum.2.39 CONNECTORS - PANEL MOUNTED

A. Microphone level XLR:1. Acceptable:

a. Male - Switchcraft D3MB, Neutrik NC3MD-L-1-BAG or approved equal.b. Female - Switchcraft D3FB, Neutrik NC3FD-L-1-BAG or approved equal.c. Features:

1) Studio quality XLR receptacle.




2) Low/stable contact resistance.3) Withstands corrosion.4) Metal construction.5) Locking connector.

d. Specification:1) Color: Black.2) Pins: 3.3) Power Rating: 500mA, 125V.

2. Line Level XLR/1/4-inch Combo:a. Acceptable:

1) Female - Neutrik NCJ6FI-S or equal.b. Features:

1) Accepts XLR and ¼-inch Phone connectors2) Low/stable contact resistance.3) Withstands corrosion.4) Solder cups.5) Metal construction.6) Locking connector.

c. Specification:1) Color: Black2) Pins: 3 and TRS.3) Current:

(a) XLR: 7.5 A.(b) ¼-inch 3A.

3. XLR Style Multi-Pin XLR Connector:a. Acceptable:

1) 3 Pin Male - Switchcraft D3MB, Neutrik NC3MD-L-1-BAG or approved equal.2) 3 Pin Female - Switchcraft D3FB, Neutrik NC3FD-L-1-BAG or approved equal.3) 4 Pin Male - Switchcraft D4MB, Neutrik NC4MD-L-1-BAG or approved equal.4) 4 Pin Female - Switchcraft D4FB, Neutrik NC4FD-L-1-BAG or approved equal.5) 5 Pin Male - Switchcraft D5MB, Neutrik NC5MD-L-1-BAG or approved equal.6) 5 Pin Female - Switchcraft D5FB, Neutrik NC5FD-L-1-BAG or approved equal.7) 6 Pin Male - Switchcraft D6MB, Neutrik NC6MD-L-1-BAG or approved equal.8) 6 Pin Female - Switchcraft D6FB, Neutrik NC6FD-L-1-BAG or approved equal.9) 7 Pin Male - Switchcraft D7MB, or equal.10) 7 Pin Female - Switchcraft D7FB, Neutrik N63FP-BAG or approved equal.

b. Features:1) Studio quality XLR receptacle.2) Low/stable contact resistance.3) Withstands corrosion.4) Metal construction.5) Locking connector.

c. Specification:1) Color: Black2) Pins: 3, 4, 5, 6 and 7.3) Power Rating: 500mA, 125V.

4. Video BNC:a. Acceptable:

1) Panel Mounted: Canary BCJ-JRU, Neutrik NBB75DFGB+NBB75FG or approvedequal.

b. Features:1) Heavy duty nickel-plated or stainless steel housing.




2) Gold plated center pin.3) Flush mounted panel connector.

c. Specification:1) Duty Cycle: 5002) Impedance: 75 Ohm.3) Ground: Isolated.

5. 35 Volt Loudspeaker HPC:a. Acceptable:

1) 4 pin metal panel: Neutrik NL4MP, Switchcraft HPCP41F or approved equal.2) 4 pin wooden box mounting: Neutrik NL4MPR, Switchcraft HPCPR41F or

approved equal.3) 8 pin: Neutrik NL8MPR, Switchcraft or equal.

b. Features:1) UL Listed2) Heavy duty construction3) Quick-Lock connection.

c. Specification:1) Contacts: 4 or 8 pin configuration.2) Current: 40 A. RMS.3) Voltage: 250 VAC.

6. Production Communications:a. Acceptable:

1) 3 Pin Male - Switchcraft D3MB, Neutrik NC3MP-BAG or approved equal.2) 3 Pin Female - Switchcraft D3FB, Neutrik NC3FP-BAG or approved equal.3) 6 Pin Male - Switchcraft D6MB, Neutrik NC6MP-BAG or approved equal.4) 6 Pin Female - Switchcraft D6FB, Neutrik NC6FP-BAG or approved equal.

b. Features:1) Studio quality XLR receptacle.2) Low/stable contact resistance.3) Withstands corrosion.4) Metal construction.5) Locking connector.

c. Specification:1) Color: Black2) Pins: 3 and 6.3) Power Rating: 500mA, 125V.

7. Data Category 6 RJ45:a. Acceptable:

1) Connector: Neutrik NE8FDY-Y110-B or equal.2) Cover: Neutrik SCDX-Green or equal.3) Lettering plate: Neutrik DSS-Green or equal.

b. Features:1) Latch lock connector.2) IDC Termination.3) CAT 6 connector.

c. Specification:1) Connector: RJ452) Duty Cycles: >10003) Bandwidth: 1 to 100 MHz4) Contacts: 85) Current: 1.5A

8. Data Category 6A Shielded RJ45:




a. Acceptable:1) Connector: Neutrik NE8FDY-Y6-B or equal.2) Cover: Neutrik SCDX-Green or equal.3) Lettering plate: Neutrik DSS-Green or equal.

b. Features:1) Latch lock connector.2) IDC Termination.3) CAT 6 rated shielded connector.

c. Specification:1) Connector: RJ452) Duty Cycles: >10003) Bandwidth: 1 to 100 MHz4) Contacts: 85) Current: 1.5A

9. USBa. Acceptable: Neutrik NKUSB-W-B or equal.

10. HDMIa. Acceptable: Neutrik NKHDMI-W-B or equal.

11. Firewirea. Acceptable: Neutrik NK1394-W-B or equal.

12. Multimode Fiber - SC Typea. Acceptable Neutrik opticalCON.

13. DC Power:a. Acceptable: Neutrik NAC3MPB or equal.b. Features:

1) Heavy-duty quick lock connector.2) “Speakon” style housing.

c. Specification:1) Contacts: 3.2) Maximum Current 20A:3) Rated Voltage: 250 V AC.

2.40 CONNECTORS - CABLEA. Microphone level XLR:

1. Acceptable:a. Male - Switchcraft A3MB or equal.b. Female - Switchcraft AD3FB or equal.c. Features:

1) Studio quality XLR receptacle.2) Low/stable contact resistance.3) Withstands corrosion.4) Metal construction.5) Screw type locking housing mechanism.6) Screw cable strain relief mechanism.

d. Specification:1) Color: Black2) Pins: 3.3) Power Rating: 500mA, 125V.

2. Line Level XLR and XLR/1/4-inch Combo:a. Acceptable:

1) Male - Switchcraft A3MB or equal.2) Female - Switchcraft AD3FB or equal.

b. Features:




1) Studio quality XLR receptacle.2) Low/stable contact resistance.3) Withstands corrosion.4) Metal construction.

c. Specification:1) Color: Black2) Pins: 3.3) Power Rating: 500mA, 125V.

3. Multi-Pin XLR Connector:a. Acceptable:

1) Male - Switchcraft A3MB or equal.2) Female - Switchcraft A3FB or equal.3) Male - Switchcraft A4MB or equal.4) Female - Switchcraft A4FB or equal.5) Male - Switchcraft A5MB or equal.6) Female - Switchcraft A5FB or equal.7) Male - Switchcraft A6MB or equal.8) Female - Switchcraft A6FB or equal.9) Male - Switchcraft A7MB or equal.10) Female - Switchcraft A7FB or equal.

b. Features:1) Studio quality XLR receptacle.2) Low/stable contact resistance.3) Withstands corrosion.4) Metal construction.

c. Specification:1) Color: Black2) Pins: 3, 4, 5, 6 and 7.3) Power Rating: 500mA, 125V.

4. High density multi-pin:a. Acceptable:

1) 48 pin: Mass W5CIRP or equal.2) 84 pin: Mass W6CIRP or equal.3) 122 pin: Mass W3CIRP or equal.4) 176 pin: Mass W4CIRP or equal.

b. Features:1) Crimp type connector design.2) Heavy-duty aluminum housing.

c. Specification:1) Color: Black2) Pin Configurations: 48, 84, 122 and 176 contacts.

5. Video BNC:a. Acceptable:

1) Cable Mounted: Belden 8281B: Switchcraft HP75BNC2, Canary BCP-C51 orapproved equal.

2) Cable Mounted: Belden 1501A: Switchcraft HP75BNC9, Canary BCP-C25F orapproved equal.

3) Panel Mounted: Canary BCJ-JRU or equal.b. Features:

1) Heavy duty nickel-plated housing.2) Gold plated center pin.3) Flush mounted panel connector.




c. Specification:1) Duty Cycle: 5002) Impedance: 70 Ohm.

6. 35 Volt Loudspeaker HPC:a. Acceptable:

1) 4 pin: Neutrik NL4FC, Switchcraft HPC14F or approved equal approved equal.2) 8 pin: Neutrik NL8FC or equal.

b. Features:1) UL Listed2) Heavy duty construction3) Quick-Lock connection.

c. Specification:1) Contacts: 2, 4 or 8.2) Current: 40 A. RMS.3) Voltage: 250 VAC.

7. Production Communications:a. Acceptable - 3 Wire System:

1) Male - Switchcraft A3MB or equal.2) Female - Switchcraft A3FB or equal.

b. Acceptable - 6 Wire System:1) Male - Switchcraft A6MB or equal.2) Female - Switchcraft A6FB or equal.

c. Features:1) Studio quality XLR receptacle.2) Low/stable contact resistance.3) Withstands corrosion.4) Metal construction.

d. Specification:1) Color: Black2) Pins: 3, 4, 5, 6 and 7.3) Power Rating: 500mA, 125V.

8. DC Power:a. Acceptable: Neutrik NAC3FCB or equal.b. Features:

1) Heavy duty quick lock connector.2) “Speakon” style housing.

c. Specification:1) Contacts: 3.2) Maximum Current 20A:3) Rated Voltage: 250 V AC.

9. Data:a. Acceptable:

1) Connector: Neutrik NE8MC6-MO or equal.2) Bushing: Neutrik BSE-5 (Green)

b. Specification1) Category 6 Cable connector.

10. Multimode Fiber - SC Typea. Acceptable Neutrik opticalCON.

11. USBa. Acceptable: Neutrik NKUSB- or equal.

12. HDMIa. Acceptable: Neutrik NKHDMI- or equal.




13. Crestron Digital Media:a. Acceptable:

1) Crestron DM-CONN or equal.2) Crestron DM-CONN-8G or equal.3) Crestron DM-CRESFIBER-CONN or equal.

2.41 EQUIPMENT MOUNTING - LOUDSPEAKERA. Loudspeaker Mounting:

1. Acceptable:a. Omnimount Professional series products or equal.b. Loudspeaker manufacturer’s mounting hardware and brackets.c. Equipment mounting per DSA approved plans.

2. Monitor Mounting Hardware:a. Acceptable: Progressive Marketing Premier Series PVCY Ceiling-Yoke Hardware or

equal.b. Features:

1) Ceiling-Yoke mount with lower tray.2) 360-degree swivel and 10-degree tilt adjustable positioning.3) Size as required for above monitor and provide ceiling mounting accessories as

necessary. Include escutcheon ring.c. Equipment mounting per DSA approved plans.

2.42 EQUIPMENT MOUNTING – VIDEO DISPLAYA. Monitor Mounting Hardware:

1. Acceptable Legrand/Chief MTM1U or equal.2. Specification:

a. Weight capacity: up to 250 lbs.b. Color: Black.

3. Equipment mounting per DSA approved plans.2.43 EQUIPMENT MOUNTING - PROJECTOR

A. Heavy Duty Universal Projector Mount:1. Acceptable: Legrand/Chief VCMU or equal.2. Specification:


3. Quantity: One for each projector provided.B. Projector Mount Adjustable Column Extension:

1. Acceptable: Legrand/Chief CMS 0305 or equal.2. Specification:

a. Color: Black.3. Quantity: One for each projector mount provided.

C. Structural Ceiling Plate:1. Acceptable: Legrand/Chief CMA345 or equal.2. Specification:


3. Quantity: One for each projector mount provided.D. Ceiling Projector Mount-Basis of Design:

1. CMA 345 ceiling plate2. CMS 003 3” speed connect fixed extension column.3. CMA 160 electrical storage enclosure




4. CMSO 305 3’ – 5’, speed connect adjustable extension column.5. RPA 094 series inverted custom projector mount.6. Tech 000018 Heavy Duty Universal Projector Bracket7. CMA 340 support bracket and stabilization cable assembly.8. CMA 275 quick snap cable cover.9. SSCI security screw cover kit.10. CMA 152 threaded pipe coupler

E. Substitutions: In accordance with Section 01 6000 - Product Requirements2.44 ACCESSORIES

A. Video Ground Loop Corrector (HBV-JBVBH1BB):1. Acceptable: Jensen ISO-MAX VBH-1BB or known equal (no known equal).2. Features:

a. Excellent picture quality.b. Waveform Distortion Prevention.c. Excellent ground loop minimization.

3. Specification:a. Frequency Response: -.80 dB at 100 kHz.b. Distortion: 3% THD.c. Common Mode Rejection: greater than 50dB.d. Insertion loss: less than -0.05 dB

4. Quantity: Use as required.B. Volume Control:

1. 25-Watt Manual Volume Control (VC-LO25):a. Acceptable: Lowell 25LVC or equal.b. Features:

1) High quality auto transformer series for use in 70-Volt system2) 10 step attenuation.3) Durable brushed stainless steel plate with skirted black knob.

c. Specification:1) Power: 25 Watt.2) Dimensions: 1 Gang.

2. 35-Watt Manual Volume Control (VC-AT-AT35):a. Acceptable: Atlas/Soundolier AT35 or equal by Lowell.b. Features:

1) High quality autotransformer series for use in 70-Volt system.2) 10 step attenuation.3) Durable brushed stainless steel plate with skirted black knob.


3. 100-Watt Manual Volume Control (VC-LO100), (VC-AT-AT100):a. Acceptable: Lowell 100LVC, Atlas/Soundolier AT100 or equal.b. Features:

1) High quality auto transformer series for use in 70-Volt system2) 10 step attenuation.3) Durable brushed stainless steel plate with skirted black knob.


C. Power Supply:1. DC Power Supplies:




a. Acceptable: Condor Linear Commercial series power supply or equal.1) Quantity: Use as required to power all DC powered equipment. Provide Power

Redundancy, 100% extra.b. Features:

1) World-wide ac input ranges and safety standards.2) Industry standard packages.3) Burn-in with cycling; 3-year warranty.4) Capacitors have highest CV & ripple current ratings.

c. Specification:1) Ac Input: 100, 120 and 240 Vac: +10%, -13%; 215 Vac: +12%, -11%; 47 to

63Hz. Tolerance for 230 Vac operation is +15%, -10%. Derate output current10% for 50 Hz operation.

2) Dc Output: See voltage rating chart from Condor. Adjustment range ±5%minimum. Select voltage as required.

3) Line Regulation: ±0.05% for a 10% change.4) Load Regulation: ± 0.05% for a 50% load change.5) Output Ripple: 3 mV +0.05% of output voltage, peak to peak maximum. All

“3-terminal regulator” outputs: 3 mV +0.2% peak to peak maximum.6) Transient Response: <50 microseconds for 50% load change.7) Short Circuit Protection: Automatic current limit/foldback.8) Overvoltage Protection: Built-in on all 5 V models, set at 6.2 V ±0.4 V. Other

models use optional overvoltage protection.9) Remote Sensing: Provided on all models; open sense lead protection built-in.10) Stability: ±0.05% for 24 hours after warmup.11) Temperature Rating: 0 to 50°C full rated, derated linearly to 40% at 70°C.12) Temperature Coefficient: ±0.01%/°C maximum.13) Efficiency: 5 V units: 45%; 12 and 15 V units: 55%; 20 and 24 V units: 60%.14) Logic Inhibit and Current-Share: F & G models.

2. AC Power Supply:a. Acceptable: Submit manufacturers’ data sheet.b. Quantity: Use as required to power all low voltage AC powered equipment.c. Features:

1) UL Listed.d. Specification:

1) Voltage: 12V AC to 48V AC.2) Power Redundancy: 100% extra.

2.45 FABRICATIONA. Equipment Enclosure Assemblies:

1. General:a. Assemble and Test the equipment enclosure assemblies in the Fabricator’s shop.b. Complete each equipment enclosure as a stand-alone assembly.

2. Equipment:a. Locate the front equipment rack rails two inches from the front of the equipment rack.b. Use mid-rails to support equipment weighing more than 50 pounds.c. Maintain accessibility to the rear of the equipment.

3. Wiring Harnesses:a. Neatly bundled all wiring in harnesses.b. Locate the wiring harness in the front of the equipment enclosure and break out the

individual pairs of cable around the side to the rear of the equipment where theconnectors are located.

c. Separate each harness service level by 3-inches.




d. Harness the patch-bay cable so that any cable can be re-routed to any otherconnector within a single patch bay.

e. Harness each individual voltage level and signal type separately as follows:1) Microphone.2) Line.3) 35-Volt loudspeaker.4) 70-Volt loudspeaker.5) Production communications.6) Control.7) Video.8) RF.

4. Cable Management:a. Secure the cable in the equipment racks with cable ties so that the connector does

not support the weight of the cable. The weight of the cable shall not apply pressurein any direction to the connector.

5. Cable Label Designation:a. Use the identical cable label designation scheme as described in Part 3 of this

Section.6. Equipment Enclosure Interconnections:

a. When 3 or more equipment enclosures located adjacent to each other,interconnection between equipment enclosures shall be accomplished withmulti-channel cable and multi-pin connector assemblies.

7. Equipment Labels:a. Label all equipment with Specified labels.b. Attach the equipment labels with permanent adhesive.c. Locate the labels on the blank or vent above each piece of equipment.d. Use descriptive labels like “Left Equalizer” “Right Amplifier”

8. Internal A/C Receptacles:a. Install grounding as shown on Drawings and described in this Section.b. Locate all internal AC receptacles on the right side of the equipment enclosure.c. Locate the lamp in top rear of each equipment enclosure.d. Provide final connection of power. Hard-wire power wiring directly to power

contactors or internal AC receptacles to ensure uninterrupted operation.9. Grounding:

a. Provide a copper ground buss in each equipment enclosure. Bond equipmentchassis with two-wire power cord to the ground buss with 12 gauge wire.

b. Bond the green ground wire from each AC outlet in the equipment enclosure to thebuss bar.

10. Field Line Terminations:a. Terminal Blocks:

1) Use Specified terminal blocks for all connections.2) Label each termination.3) Terminate all field line entering and leaving the equipment rack.

11. Patch Bays:a. Clearly and neatly label the patch bays with the connector assignments.b. Numbered the patch bays sequentially.c. All work on the patch bays shall be accomplished using tools and support hardware

designed for the patch bay system and following procedures identified by themanufacturer.

B. Power Sequencing Programming:1. Program the power sequence as follows:

a. Power Sequence On:




1) Energize the power to the source equipment then all processing equipment thenall of the power amplifiers in 15 Amp intervals. Delay each sequence by .2seconds.

b. Power Sequence Off:1) De-Energize the power to the power amplifiers then all of the processing

equipment then all of the source equipment. Delay the power amplifiersequence until the power capacitors completely de-energize then eachsuccessive sequence by 1 second.

c. Fire Alarm Sequence:1) De-Energize the power to the power amplifiers when the fire alarm is activated.

d. Energize the power to the power amplifiers when the fire alarm is not activated.C. AV Plates:

1. General:a. The AV Plate details in the Contract Drawings do not distinguish between flush or

surface mounted plates. It is the contractor’s responsibility to size each AV Platebased on the field condition.

b. Coordinate the AV Plate size and mounting condition with Division 26.2. Cable Management:

a. See Cable Installation requirements in this Section for the Cable Installationrequirements.

3. AV Plates with surface mounted back boxes:a. Fabricate the AV panels so that they are flush with the back-box edge. No part of the

AV panel shall extend beyond the back-box creating a sharp edge.b. See the Contract Drawings for details.

4. AV Plates with back boxes that are recessed in the wall:a. Fabricate the AV Panels so that they are flush with the wall surface and no part of the

AV Back-box or unfinished wall surface is visible. Extend the AV Panel beyond theopening in the wall creating a flush finished appearance.

b. See the Contract Drawings for details.D. Programming:

1. Program the hardware.2.46 FINISHES

A. Manufacturer’s logos:1. Remove all manufacturers’ names, logos, or other symbols from devices mounted in a

public space.B. Custom Fabricated AV Plates:

1. Finish the custom fabricated plates that are not visible in public areas in brushed, anodizedblack.

2. Finish the custom fabricated plates that are visible in public areas in brushed, anodizedclear aluminum finish.

3. Finish all standard gang plates in brushed stainless steel.4. Engrave the Plates with 3/16” high characters.5. Fill the characters in contrasting colors.

a. Black AV Plate: Fill engraving with black paintb. Clear aluminum and stainless steel AV Plate: Fill engraving with black paint.

C. Custom Fabricated Plate Screws:1. Match the finish of the screws used to mount the custom fabricated plates with the finish of

the custom fabricated plate.D. Ceiling Loudspeaker Grilles:

1. Paint all loudspeaker grilles so that the color is an exact match with the immediatesurrounding ceiling area color.




E. Surface Mounted Loudspeakers:F. All surface mounted loudspeakers shall be black unless specifically specified in Part II.

1. Control Interfaces:a. All control interfaces bezels and button panels shall be black unless specifically

specified in Part II.G. Projector Mounts:

1. All projector mounts shall be black unless specifically specified in Part II.2.47 SOURCE QUALITY CONTROL

A. Fabrication Tolerances:1. General:

a. Each item shall be a product of a firm regularly engaged in the manufacture ofelectrical, electronic or optical equipment. The equipment shall be the latest model ortype offered which meets the applicable specifications at the time of the submittal. Discontinued items replaced by newer models or versions are prohibited and shouldnot be submitted for review.

b. Quality of workmanship and fabrication of all equipment and components which arecustom fabricated shall be comparable to professional equipment produced byspecialized manufacturers of the trade involved and shall be verified by inspection. Only firms having 5 years experience in all aspects of the fabrication and installationof similar systems shall be allowed to perform the work.

2. All materials and products shall be new and of professional quality. Unless specificallystated in the drawings or specifications, no existing or used materials shall be installed.

3. Substitutions:a. Substitutions of equal equipment beyond the alternatives listed shall be permitted only

in accordance with Division 1. If a requested substitution requires a change in any ofthe contract drawings, a revised drawing must be submitted as part of the substitutionrequest. The Owner’s Representative shall be the final judge of the acceptability ofsubstitutions.

b. By making requests for substitutions, the Contractor:1) Represents that the Contractor has personally investigated the proposed

substitute product and determined that it is equal to or superior in all respects tothat specified.

2) Represents that the Contractor will provide the same warranty for the substitutionthat the Contractor would for that specified.

3) Certifies that the cost data presented is complete and includes all related costsunder this Contract and waives all claims for additional costs related to thesubstitution which may later become apparent.

4) Coordinate the installation of the accepted substitute, making such changes asmay be required for the Work to be complete in all respects equal to thedesigned system before the substitution was made. In the event that thesubstituted material or equipment fail to meet performance testing standardsafter installed replace substituted equipment with the specified equipment.

4. Loudspeaker Substitutions:a. Loudspeaker Substitutions shall be accompanied with EASE data supporting the

substitution.B. Shop Fabrication Inspection:

1. Notify the Owner’s Representative in writing that the system has met all of therequirements for the Shop Fabrication Inspection and is ready for the Shop FabricationInspection two weeks prior to the Inspection.

2. Demonstrate to the Owner’s Representative that all equipment is operating as specifiedbefore the equipment is delivered to the project site.




3. Verify the achievement of the specifications for each electronic component in situ, i.e., asassembled in its console, equipment enclosure or other enclosure, powered by the systempower supply and with all other components also activated, i.e., powered andinterconnected. The magnitude and character of the threshold noise shall be observed forappearance of hum in excess of that present with individual activation, or the appearanceof high frequency oscillation.

4. Test the projection equipment to verify that the manufacturer's specifications are met afterit has been incorporated into a complete subassembly.

5. Tested the video equipment to verify that its operation meets the manufacturer'sspecifications and EIA RS-170A after assembly into complete subsystems.

C. Verification of Performance:PART 3 - EXECUTION3.01 EXAMINATION

A. Audiovisual Infrastructure:1. Examine the audio-video system infrastructure as-built condition to discover all of the field

changes to the audio-video system infrastructure.a. Verify that all of the audio-video system back-boxes shown on the EAV category

Drawings match the plate size Shown on the AVS drawings. If they do not, match theplate with the backbox. In the event that the backbox that has been installed is toosmall and will not accommodate the AV receptacles notify the Owner’sRepresentative.

b. Verify the As-Built conduit capacity. In the event that the conduit that has beeninstalled is too small and will not accommodate the AV cables, notify the Owner’sRepresentative.

c. Examine pathway elements intended for cables. Check raceways, cable trays, andother elements for compliance with space allocations, installation tolerances, hazardsto cable installation, and other conditions affecting installation.

d. If the conduit or back-boxes are deficient in any way notify the Owner’sRepresentative in writing before the shop drawings are submitted.

2. Examine walls, floors, ceilings, roofs, equipment bases, and supports for suitableconditions where audio-video systems are to be installed.

3. Verify that the AC power has been installed and tested.4. Verify that the isolated ground for AC power circuits has been implemented correctly.5. Proceed with audio-video equipment installation only after the unsatisfactory conditions

have been corrected.3.02 PREPARATION

A. Audiovisual Equipment Rooms.1. Prepare rooms that will have audio-video equipment installed in them by completely

finishing the Work associated with the room. Complete the following items before theaudio-video equipment components are installed:a. Painting.b. Ceilings.c. Windows.d. Millwork.e. Doors.f. Door Locks.g. Cleaning.h. Floor coverings.i. Electrical Work.

2. Verify that all of the environmental requirements described in Part 1 if this Section ProjectSite Conditions have been completed.




B. Proceed with audio-video equipment installation only after the unsatisfactory conditions havebeen corrected.

3.03 INSTALLATIONA. General:

1. Furnish all labor, materials, equipment, programming, and incidental items necessary forconstruction and completion of the audio-video system described in the Specifications andshown on the Drawings.

2. In case of a discrepancy between these overall system standards and the individualequipment item specifications, or manufacturers’ recommendations, the most stringentshall govern.

3. Assistive Listeninga. Comply with 2016 CBC 11B-219 & 706.

B. Cable Installation:1. General:

a. See the EAV category Drawings and Section 26 05 34 Raceway and Boxes forAudio-Video Systems for additional information.

2. Quality Assurance:a. Pull the cable without damage to the insulation or deformation to the conductors.b. Install the cable in conduit.c. Do not install cable in the

3. Separation of electrical signal levels:a. Each conduit shall contain cable of the same signal level or the same type of circuitry

only. Install each separate electrical service level cable designation type shown onthe AVS Drawings in their respective, separate conduits.

b. Separate all low voltage signal levels by 2” minimum.c. Separate all low voltage signal levels running parallel to 120 and 240 Volt AC power

by 3’ minimum.d. Separate all low voltage signal levels running parallel to AC power greater than 240

Volts by 6’ minimum.e. Low voltage signals shall cross AC power perpendicular to each other.

4. Terminations, Splices and Taps:a. Splices are not allowed.b. Wirenuts are not allowed.c. Pull all cable from device to device directly through terminal, junction, pull and AV

back-boxes without splices or terminations.d. Tin the bare wire prior to termination unless the connector manufacturer specifically

recommends otherwise.e. Individually insulate unused ends of line level shields with shrinkable tubing and

attached to the cable using an additional piece of shrinkable tubing.5. Cable Service Loop:

a. Create a cable service loop within the equipment rack by routing the cable enteringthe top of the equipment rack, from the top to the bottom of the equipment rack, thento the equipment. Do this in a manner that will allow the cable to be re-routed withinthe equipment rack in the future.

b. Create a cable service loop within the equipment rack by routing the cable enteringthe bottom of the equipment rack, from the bottom to the top of the equipment rack,then to the equipment. Do this in a manner that will allow the cable to be re-routedwithin the equipment rack in the future.

6. Cable Labels:a. Clearly label both ends of each cable during the installation with cable labels.b. Consecutively number the cable with respect to the devices, the leading service level

designation type.




c. Install cable labels 3” from the connector or termination at each end of the cable.7. Cable Designation:

a. Format the Cable Designation as follows:1) “Leading Cable Designation Type” “-“ “Cable Number”.

b. Example:1) M-45 = Microphone number 45.2) L-122 = Line number 122.3) L-1122 = Line parallel to line L-122.4) AES-1 = Digital Audio number 1.

c. Acceptable Cable Designation Type example:1) M = Microphone Level Audio.2) L = Line Level Audio.3) S = Speaker.4) D = 70Volt Speaker.5) DA = Digital Audio.6) AES = AES/EBU Digital Audio - Balanced.7) AESU = AES/EBU Digital Audio - Un-Balanced.8) SDV = Serial Digital Standard Definition Video.9) SDH = Serial Digital High Definition Video.10) V = Composite Video.11) SV = S-Video.12) RGB = Component Video.13) RGBHV = RED, Green, Blue, Horizontal Sync, Vertical Sync Video.14) RF = Radio Frequency 75 Ohm.15) WRF = Radio Frequency 50 Ohm.16) NET = Cat 5, Cat 6 Network.17) C = Digital Control.18) DC = Direct Current Power.19) F = Fiber Optic Power.20) SF = Single-Mode Fiber.21) MF = Multi-Mode Fiber.

8. Cable Management:a. Bundled and route cables by type from source to termination uniformly to the

equipment enclosures.b. Install edge protection material ‘cat track’ or grommets on the edges of devices where

cables cross a metal edge.c. Secure the cable with cable ties, Kelems grips or approved device so that the

connector does not support the weight of the cable. Size the cable managementdevice as required. The weight of the cable shall not apply pressure in any directionto the connector.

C. System Grounding:1. The grounding system shown in the AVS Drawings is designed to avoid ground loops and

inductive coupling. Do not deviate from the grounding system scheme without priorapproval.

2. The system shall be hum free, stable and free of oscillation with the earth groundtemporarily disconnected.

3. Ground the system to “Earth Ground” at one point in the system as shown on theDrawings. Comply with National Electric Code 1996 paragraphs 250-74 Exception No. 4,250-75 Exception and 384-20 Exception.

D. Power Sequencing Fire Alarm Input:1. Fire Alarm Panel Connection:




a. Connect the power sequence fire alarm input to the fire alarm panel with a supervisedcontrol line.

b. The supervised line maintains a constant voltage to the dry contact closures of thePower Sequencing System and the Fire Alarm Panel.

E. AV Plates:1. Mounting General:

a. Equipment mounting per DSA approved plans.1) The AV Plate details in the Contract Drawings do not distinguish between flush

or surface mounted plates. It is the contractor’s responsibility to size each AVPlate based on the field condition.

2) Coordinate the AV Plate size and mounting condition with Division 26.2. AV Panel Screws:

a. Mount all AV panels to the back-box with 10-32 pan-head screw hardware. Drill andtap the back box.

b. Countersink the AV plate to one half the depth of the screw head.c. The mounting screws shall match the finish of the AV Plate.d. Use two screws on each side of the panel for AV Plates that have a side that is twelve

inches long or longer.e. Use two screws on the left and right or top and bottom of the AV Panel for AV Panels

that have no side larger than twelve inches long.3. Cable:

a. See Cable Installation requirements in this Section for the Cable Installationrequirements.

4. AV Plates with surface mounted back boxes:a. Install the AV panels so that they are flush with the back-box edge. No part of the AV

panel shall extend beyond the back-box creating a sharp edge.b. See the Contract Drawings for details.

5. AV Plates with back boxes that are recessed in the wall:a. Install the AV Panels so that they are flush with the wall surface and no part of the AV

Back-box or unfinished wall surface is visible. Extend the AV Panel beyond theopening in the wall creating a flush finished appearance.

b. See the Contract Drawings for details.F. Free Standing Equipment Enclosure:

1. Equipment mounting per DSA approved plans.2. Connect audio field lines entering the equipment enclosures with an intermediate terminal

block. In the event that a patch bay with connectors is specified, the patch bay may serveas the terminal block.

3. Connected Video field lines entering the equipment enclosure directly to the switch orvideo patch bay.

4. Electrically isolated the equipment enclosure from:a. The building grounding system.b. The conduit system. Use nylon bushings.c. The building structural steel.

5. Electrically bond the equipment enclosures at one point to the isolated grounding system. See the AVS category drawings for grounding details.

6. Mount the equipment enclosure on an isolator base made of treated wood. See the AVScategory drawings for mounting details.

G. Wall Mounted Equipment Enclosure:1. Equipment mounting per DSA approved plans.2. Connect field lines entering the equipment enclosure directly to the equipment.3. Service Loop:




a. Provide a twelve-foot service loop so that the equipment rack insert can be removedfrom the enclosure housing for service.

b. Start the service loop from the top of the equipment enclosure and secure it to the topof the movable equipment insert.

4. Electrically isolated the equipment enclosure from:a. The building grounding system.b. The conduit system. Use PVC bushings to terminate the equipment enclosure to the

conduit.c. The building structural steel.


6. Mount the equipment enclosure on an isolator base made of treated wood. See the ACScategory drawings for mounting details.

H. Millwork Mounted Equipment Enclosure:1. Install the equipment enclosure as shown on the drawings.2. Connect field lines entering the equipment enclosure directly to the equipment.3. Service Loop:

a. Provide a twelve-foot service loop so that the equipment rack insert can be removedfrom the enclosure housing for service.

b. Start the service loop from the top of the equipment enclosure and secure it to the topof the movable equipment insert.

4. Electrically isolated the equipment enclosure from:a. The building grounding system.b. The conduit system. Use PVC bushings to terminate the equipment enclosure to the

conduit.c. The building structural steel.


6. Mount the equipment enclosure on an isolator base made of treated wood. See the ACScategory drawings for mounting details.

7. Install the cooling system in the back of the millwork cabinet to vent the heat out of themillwork. Connect the cooling unit directly to the AC power.

I. Device and assemblies mounted to the building structure:1. Install every device according to the Structural Engineer’s Stamped Drawings.2. Seismic Restraints:

a. Secure all hanging and free-standing equipment to the building structure so that itresists seismic acceleration of 1g in any direction or as required by the StructuralEngineer. The structural Engineer’s recommendation supersedes the 1grequirement.

b. Comply with the local building codes and the most recent version of the CBC.c. Submit calculations and detailed drawings stamped by a registered engineer in the

project State.d. The seismic restraints are not shown on the Contract Drawings. It is the Contractor’s

responsibility to develop shop drawings that reflect the field condition and the seismicrequirements.

J. Video Projector1. Equipment mounting per DSA approved plans.2. Align, register and color balance the video projector for the following resolutions:

a. 1024 x 768, 60Hz, 70Hz, 72Hz and 75Hz.b. 720pc. 1080id. 1080P




e. 4Kf. The native resolution of the projector.

K. Wall Mounted Loudspeaker Installation:1. Equipment mounting per DSA approved plans.2. Coordinate the receptacle that serves the loudspeaker directly behind the loudspeaker so

that the cable, connectors and cover-plate are not visible. Coordinate this with Division 26.3. When a powered loudspeaker is specified, coordinate the receptacle that serves the

loudspeaker power directly behind the loudspeaker so that the cable, connectors andcover-plate are not visible. Coordinate this with Division 26.

L. Reinforcement Loudspeaker Installation:1. Equipment mounting per DSA approved plans.

M. Control System Network Deployment:1. Configure the Control System as an independent VLAN separate with a bridge to the

Owner’s Network. Configure the network router so the Owner has access to all of thecontrollable devices as follows:a. Crestron control system Ipad, iPhone and Android device control.b. Network controllable devices with web browser interface control.

2. Configure the Video Projector Remote Monitoring to:a. E-mail the Owner when the lamp life is low, and all alerts.b. Status monitoring.

N. Audio System Network Deployment:1. Configure the Audio System as an independent VLAN separate with a bridge to the

Owner’s Network. Configure the network router so the Owner has access to all of thecontrollable devices as follows:a. Crestron control system iPad, iPhone and Android device control.b. Network controllable devices with web browser interface control.

3.04 FIELD QUALITY CONTROLA. General:

1. The Verification and Performance Tests documented in this Section represent theminimum system testing required to fulfill the Contract Document Verification andPerformance Testing requirements. Additional tests not documented in this Section will berequired to make the system Fully Operational.

2. Record the results of each Test in this Section in the Project Operations and ServiceManual described in Part 1 of this Section. Recorded the date each Test was completedand the results of each Test.

3. Engage a factory-authorized service representative to assist with Performance Testing,Verification as needed.

B. Verification Tests:1. System Energizing:

a. Prior to energizing the system for Testing and Verification, make certain that:1) All products are installed in a proper and safe manner in accordance to the

manufacturer’s instructions.2) That the insulation and shrinkable tubing is present where required.3) All dust, debris, solder splatter, etc. is removed.4) Temporary facilities and utilities have been properly disconnected.5) Electronic devices are properly grounded.6) Electrical mechanical connections are secure.

2. Loudspeaker Circuit Verification:a. Provide a low level, band limited test signal to each amplifier input.b. Turn on one channel of Amplifier #1 and verify that the correct loudspeaker or group

of loudspeakers is operating. Correct any wiring or other problems found.




c. In a similar manner, check each channel of all remaining amplifiers and theirrespective loudspeaker circuits.

3. Constant Voltage Loudspeaker Verification:a. Play a pink noise signal through each group of constant voltage loudspeakers. Only

one amplifier channel should be on at a time.b. Walk the area covered by the loudspeakers to verify that each loudspeaker is

operating and that there are no significant changes in volume level from oneloudspeaker to the next. Verify that the extent of coverage is consistent through thearea.

4. Loudspeaker Polarity Verification:a. Use an electronic polarity checker, TEF-20, SYSID, SIM II, or other similar equipment

to test each reinforcement loudspeaker. All loudspeakers should have the samerelative polarity.

b. In a similar manner, check all distributed loudspeakers to ensure they have the samepolarity.

5. Loudspeaker General Performance Verification:a. Verified the general performance of each loudspeaker unit by sending it a pink noise

signal at 10.0 Volt level and verifying the specified output SPL at a distance of 1 foot.b. Verified normal undistorted sound quality by headphone listening at the output of the

calibrated system.c. Feed each loudspeaker with an oscillator signal at 10.0 Volt level within its intended

frequency range, verifying absence or abnormal distortion of rattles due to installation.6. Headroom Verification:

a. Once the preceding tests and adjustments have been completed, play a variety ofmusical programs through the system. Amplifiers should be off for this test.

b. Adjust the console gain to achieve peak output levels of +6 VU on the consolemeters.

c. Observe if any of the components indicate clipping or less than 3 dB of headroom.d. Replace the musical program with a steady 1000 Hz sine wave. Connect an

oscilloscope or similar equipment to selected amplifiers in each portion of thereinforcement system.

e. Increase the output level of the console until the signal displayed on the oscilloscopebegins to show distortion.

7. Remote Input Verification:a. Using a microphone or portable signal generator, connect to each microphone

receptacle throughout the facility.b. Verify that the receptacle under test appears at the correct position on the patch bay

and is operating properly.c. In a similar manner, check all remote tielines and media related lines for correct wiring

and labeling.8. System Gain Adjustment:

a. Adjust each active piece of equipment for proper gain from the console output to theinput of the amplifier.

9. Video Camera Verification:a. Prior to installing the lens on the camera, manually verify that the lens is dust free and

that the zoom, front focus, iris, and rear focus rings move freely.b. For conference rooms, classrooms, etc. verify that all lighting fixtures have the proper

temperature bulbs for video and the light is even across the room.c. Using system control, verify the range of all lens components i.e. Zoom, focus and

iris.10. Wiring and Cabling:

a. Verify that all of the wiring is correctly and completely installed.b. Perform the following Verification:




1) Short Circuit Conductor - Verify that there are no short circuits betweenconductors within any cable.

2) Short Circuit Cable - Verify that there are no short circuits between cable tocable.

3) Open Circuit - Verify that there are no open circuits.4) Circuit Polarity - Verify that each AC circuit is 0 degrees in phase with respect to

the system.C. Performance Tests:

1. General:a. Perform all tests in accordance with manufacturer's written instructions.b. Use particular caution when testing equipment containing solid-state components and

loudspeakers.c. Set and operate controls to demonstrate their functions and capabilities in a

methodical sequence that cues and reproduces actual operating functions.d. When testing the system involving equipment provided under other Sections, combine

testing required by this Section with that required by the Sections specifying the otherequipment.

2. Testing Documentation:a. Document all tests and submit in accordance to Division 1 and Part I of this Section.

3. AC Power Receptacle Testa. Test:

1) Test each AC power receptacle with a circuit tester for proper hot, neutral andground connections.

4. DC Resistance Test:a. Test:

1) Measure the DC resistance between the technical ground in each equipmentrack, console and the main building ground.

b. Specification:1) Resistance should be 0.15 ohms or less.

5. Technical Ground Test:a. Test:

1) Temporarily lift the technical ground from the main electrical ground, measurethe DC resistance between them.

b. Specification:1) Resistance should be 1000 ohms or greater.

6. Loudspeaker Circuit Test:a. Test:

1) Measure the impedance of each loudspeaker cable. For full rangeloudspeakers, use a frequency of 1000 Hz and 100Hz, for band limitedloudspeakers, use a frequency appropriate for the operating range of thetransducer. When documenting the results of these tests, include the calculatedimpedances based on number of units on a line and the size and distance of therun.

b. Specification:1) Correct any field readings that differ more than 20% from the calculated

impedances.7. Signal to Noise Test:

a. Test:1) Test the Signal to Noise through each piece of equipment.

b. Specification:1) The signal to noise ratio of the system as installed shall be no greater than 1dB

across any line.8. Cross Talk:




a. Test:1) Cross talk between channels shall be measured with signal equivalent to 1.0

Volts output into 1 channel with its gain off and the gain of each other channelvaried over their full range.

b. Specification:1) Maximum signal leakage at the system output must be not greater than -70 dB

re 1.0 Volt at the pre-amp output at 1 kHz, increasing to -52 dB at 8 kHz.9. Video Signal Level Test:

a. Test:1) Feed the video system with a "known good signal" from a video signal generator.

b. Specification:1) Video outputs shall conform to EIA RS-170A.

10. Video Signal Chain Test:a. Test

1) Feed the video system with a "known good signal" from a video signal generator.b. Specification:

1) All equipment and video signal chains shall operate according to themanufacturer's specifications.

11. Video Switching and Distribution Test:a. Test:

1) Using a RS170A compliant test signal generator, ensure that there is no signaldegradation from each input to each output. Make adjustments as required.

b. Specification:1) Luminance level at 100 IRE white, sync tip at -40 IRE.2) Ensure the color burst ranges from -20 to +20 IRE.3) Verify the maximum chrominance levels of the first two color bars (yellow and

cyan). Both should be at exactly 100 IRE.4) Verify there is no excessive frequency roll-off by verifying that the ends of the

first two color bars drop less than 2 IRE from the above check.5) Using a vector scope, ensure that each of the primary and secondary colors fall

within the 2% box.6) Check the Signal to Noise ratio and verify that it has not increased more than 1%

through the system from the manufactures published specification.12. Video Camera Black Level Test:

a. Test:1) Set the iris to approximately 75% open. Verify lighting is even and that there is

no flaring, adjust iris as required to remove flaring.2) Connect a waveform / vectorscope the output of the camera.3) Cap the lens or block the front of the lens with an opaque substance such as a

piece of cardboard.b. Specification:

1) On the vectorscope, verify that the camera output produces a “fuzzy” spot in theexact center of the display.

2) On the waveform monitor verify the black level.3) Adjust as necessary for proper results.

13. Video Camera White Level Test:a. Test:

1) Set iris to approximately 75% . Verify lighting is even and that there is no flaring,adjust iris as required to remove flaring.

2) Connect a waveform / vectorscope the output of the camera. Zoom the cameraonto a pure white spot, paper, etc. Use the front focus adjustment and ensurethe object is in focus.

b. Specification:




1) Verify with a vectorscope that the camera output produces a “fuzzy” spot in theexact center of the display.

2) Verify the white level using a Waveform monitor. Adjust as necessary for properresults.

14. Video Source Equipment Test:a. Test:

1) At the furthest destination point from the source equipment output color bars,verify the following and adjust as required:

b. Specification:1) Luminance level at 100 IRE white, sync tip at -40 IRE.2) Ensure the color burst ranges from -20 to +20 IRE3) Check the maximum chrominance levels of the first two color bars (yellow and

cyan). Both should be at exactly 100 IRE.4) Verify there is no excessive frequency roll-off by verifying that the ends of the

first two color bars drop less than 2 IRE from the above check.5) Using a vector scope, ensure that each of the primary and secondary colors fall

within the 2% box.6) Check the Signal to Noise ratio and verify that it has not increased more than 1%

through the system from the manufactures published specification.15. RF Distribution Test:

a. Test:1) Set the modulators channels as defined on the AVS category Drawings for the

RF System.2) Input a video signal from one of the source equipment into each of the

modulators.3) Adjust modulator outputs to the signal strength shown on the AV category

Drawing.b. Specification:

1) Measure the signal at each of the connector plates and record initial results.2) The signal levels should be +10db plus or -7db. Add additional RF pads as

required to meet this requirement.3) Using a TV with tuner, verify that the picture quality is clear with no noise visible.

16. UTP Test:a. Test:

1) Test UTP cable in accordance with the referenced "Standards".b. Specification:

1) Category 5e and Category 6e.17. Multi-mode Fiber Test:

a. Specification:1) Perform tests at both 850nm and 1300nm.2) Test procedure to be ANSI/EAI-526-14A-Test Method B any applicable

amendments.3) Tests are to be performed with optical source and power meter.4) Signature Trace Measurements are to be performed and record using OTDR at

both 850nm and 1300nm.5) Identify and resolve any discrepancies.6) Trace the Wavelength.7) Trace the Pulse Width setting.8) Trace the Index refraction.9) Trace the Fiber and cable number.10) Trace the Test locations.11) Trace the Segment length.12) Trace the End to end loss.




18. Single-mode Fiber:a. Test:

1) Perform tests at 1310nm and 1550nm.2) Test procedure to be ANSI/EAI-526-7-Test Method A.1 and any applicable

amendments.3) Tests are to be performed with optical source and power meter.4) Signature Trace Measurements are to be performed and recorded using OTDR

at both 850nm and 1300nm.b. Specification:

1) Identify and resolve any discrepancies.2) Trace the Wavelength.3) Trace the Pulse width setting.4) Trace the Index refraction.5) Trace the Fiber and cable number.6) Trace the Test locations.7) Trace the Segment length.8) Trace the End to end loss.

19. Control Test:a. Test programmable control related to light balancing, occupancy sensing, and other

controls under conditions that simulate actual operational conditions.20. Digital Media Video Test:

a. Crestron Digital Media Commissioning Report Toolbox for DM products.b. The number of HDCP KSVs ? Keys supported by each source.c. The video timing, HDCP use and audio format of each source when operating.d. The video timings and supported audio formats for each connected sink.e. The video timings and supported audio formats presented in the EDID to each source

- the preferred video timing shall be indicated.f. The length of cable used on all shielded twisted pair cable used for AV distribution.g. The data rate supported by each shielded twisted pair cable used for AV distribution.

D. Test Equipment:1. Furnish the following equipment as requested. Equipment to be available for the entire

test period through final system testing:a. Sound Level Meter: ANSI S1.4-1971 Type SEA with digital or analog display. Meter to

provide ranges of 40 to 120 dBA.b. Impedance Meter: Capable of testing audio lines at three frequencies, minimum,

between 250 Hz and 4k Hz. Measurement Range: 1 Ohm to 100 kOhms.c. Multimeter-Measurement range: DC to 20kHz, 100 mV to 300V, 10 mA to 10 A.d. Audio Oscillator: bandwidth 20 Hz to 20k Hz ±1 dB at 0 dBm output. Output to be

balanced. Oscillator to include adjustable output level.e. Ladders and scaffolding necessary to inspect all loudspeakers.f. Temporary 1000 foot microphone cable for testing purposes.g. Videotek TSM-61 Waveform and Vectorscope monitor.h. Sencore SLM 1453 RF Signal Level Meter.i. Videotek VSG 201.j. Extron VTG 400D.k. Provide three portable UHF band radios during all Inspections.

3.05 ADJUSTINGA. Loudspeaker adjusting:

1. The loudspeaker details shown on the Drawings show the approximate angle of theloudspeakers. The final adjustments to the loudspeaker positions will be made during theFinal Inspection with the assistance of the Owners Rep.




B. Signal Delay Adjustment:1. Adjust the delay to each subsystem to ensure proper synchronization between the main

loudspeakers and delayed loudspeakers.2. Using a TEF 20, SYSID, Smaart, SIM II, or an approved time-based measurement system,

measure the arrival time of the distant signal and then measure the arrival of the localsignal. Based on the arrival times measured, adjust the delay applied to the localloudspeakers to synchronize them with the distant loudspeakers. Repeat the test to verifythe delay has been set to within 1 ms of the arrival of the distant signal.a. Continue to test and adjust each separate subsystem with a dedicated delay channel.

C. Level Adjustment - Reinforcement System:1. Adjust the gain of each amplifier to provide a consistent and appropriate volume level

throughout the facility.2. Begin by connecting a pink noise source to one input of the mixing console. Adjust the

console output to -10 dB on the VU meter. Adjust the appropriate amplifiers to achieve 85dBA in the area covered by one section loudspeakers. Use a calibrated sound level meterto make the measurement.

3. If the test group of loudspeakers employs an active crossover, use an FFT based analyzer,TEF 20, SYSID or Smaart to balance the spectrum by adjusting the level for each band.

4. Once the initial loudspeakers have been properly adjusted, begin adding the loudspeakersin each adjacent areas and repeating the same adjustments. When a given area orseating level has been completed, move to the next lower area and repeat the tests andadjustments for that area.

5. Amplifier settings for loudspeakers covering similar seating areas should have the samegain settings. Investigate and correct any occurrences where an amplifier deviates morethan 2 dB from the average.

6. Amplifiers should be set to provide an average of 85 dBA ±1.5 dB throughout each seatingsection.

D. Amplifier Level Adjustment - 70 Volt System:1. Adjust the level of 70 volt system to achieve a volume level appropriate for their location

and intended use.2. After setting the amplifier level for each system, play a pink noise signal over the

loudspeakers and walk through each area. Using a sound level meter, identify any areaswhere the SPL changes by more than 3 dB. Identify the cause of the change and where itis due to mounting height or architectural differences, adjust the transformer taps of theaffected loudspeakers to bring the sound level within range.

E. System Equalization:1. Use SMAART to equalize all loudspeaker system. The equalized loudspeaker will have an

average frequency response, +/- 3dB within the audience seating area.a. Use four identical measurement microphones located randomly within the audience

seating area to measure the loudspeaker response. The microphones shall have acapsule diameter of ¼” or less. Microphones equivalent to Earthworks M30 areacceptable.

2. Equalization methods using Real Time Analyzers (RTA’s) are specifically un-approvedmethods of equalization.

F. Video Camera Focal Adjustments:1. Zoom the lens all the way out. Adjust rear focus ring to bring objects at far end of view into

focus.2. Zoom the lens all the way in. Adjust the front focus to bring near objects into focus.

G. Verify that the picture stays in focus while traveling to the extents of the zoom function.1. Camera Resolution:

a. Using a SMPTE camera resolution chart verify the camera’s resolution performanceis within the specifications of the camera.




b. Adjust as required to bring within specifications. Note: any adjustments performed willrequire that the black and white level adjustment be re-verified.

H. Video Projector:1. Completely fill projected images with their respective screen formats to full size without

"cropping".2. Projection lenses shall provide distortion free images without color fringing or aberration.3. Using a RS170A compliant test signal generator, Insert SMPTE color bars and adjust

brightness and contrast accordingly4. Using a RS170A compliant test signal generator, insert a cross-hatch pattern and adjust

convergence as required.I. Slide Projection:

1. Slide projectors shall be tested for proper image size, focus and brightness. TheContractor shall supply 3 each of the following precision test slides for checkout of theslide projectors of each system:

2. Image size slide - shows single frame, double frame and "instamatic" image sizes on asingle "superslide".

3. Resolution slide - provides for focus adjustment and resolution observation.4. Typeface slide - provides legibility information.5. Grey scale slide - shows effect of ambient light on projected images.

J. Video Monitor:1. Setup and adjusted video monitors following the manufacturer's guidelines using a blue

gun including the following:a. Black level, using the brightness control.b. White level, using the contrast control.c. Correct Hue.

2. Three months after the date of Substantial Completion, provide sixteen hours, to adjustaudio-video system, make program changes, and adjust the audio-video system to suit theactual operational conditions.

3. LCD Display (LCD-NC-V423-AVT)a. Acceptable: NEC V423-AVT or equal

3.06 CLEANINGA. Clean all provided equipment and devices internally and externally using methods and materials

recommended by manufacturers.B. All provided equipment shall be free from dust at the time of the Substantial Completion

Inspection and the Final Inspection.C. Repair damaged finishes.

3.07 SUBSTANTIAL COMPLETION INSPECTIONA. General:

1. Notify the Owner’s Representative in writing that the system has met all of therequirements for Substantial Completion and is ready for the Substantial CompletionInspection two weeks prior to the Inspection. The notice must be written and signed by themajority share holder if the company is a closely held corporation or the President in apublically traded company or Sole Proprietorship.

2. Provide the services of the Project Engineer described above, the Project Manager and afield service technician to the Owners Representative to make adjustments during theSubstantial Completion Inspection.

3. Assist the Owner’s Representative in performing final system tests and adjustments.4. Provide all labor, materials, tools and test equipment necessary for these tests and

adjustments.




5. Inspections will be performed using Bluebeam Revu software. The Contractor is requiredto read, listen, watch and view inspection reports from interactive .pdf software withimbedded audio, video and photographs.

B. System Demonstration:1. Demonstrate the:

a. Overall system operation.b. Control system operation.c. DSP software control operation.d. Optics system field performance.e. Electro-acoustic field performance.f. Audio system field performance.g. Video system field performance.h. Production Communications system field performance.i. RF system field performance.j. Performance Tests verification (as described in Part 3 of this Section).

C. Loose Equipment and Documentation:1. Provide the following items on-site for inspection:

a. Operations and Service Manual.b. Shop Drawings.c. Portable Equipment.d. Shop Test Report.e. Field Test Report.

D. Failure:1. In the event that the system fails to meet the criteria for Substantial Completion all of the

costs for additional inspections shall be borne solely by the Contractor. Costs include:a. Consulting fees.b. Travel and daily expenses.

E. Deficiencies:1. After the Substantial Completion Inspection the Owner’s Representative will issue a report

documenting the system deficiencies.3.08 FINAL INSPECTION AND ACCEPTANCE:

A. Notify the Owner’s Representative in writing that the system has met all of the requirements forFinal Inspection, all of the Deficiencies List form the Substantial Completion Inspection hasbeen completed and is ready for the Final Inspection two weeks prior to the Inspection.

B. Submit digital photographic evidence of the corrected deficiencies from the SubstantialCompletion Inspection Deficiencies List to the Owner’s Representative.

C. Provide the services of the Project Engineer described above, the Project Manager and a fieldservice technician to the Owners Representative to make adjustments during the FinalInspection.

D. Assist the Owner’s Representative in performing final system tests and adjustments.E. Provide all labor, materials, tools and test equipment necessary for these tests and

adjustments.F. Final acceptance of the installation will be granted when it is clear to the Owner’s

Representative that the following conditions have been satisfied.1. All of the deficiencies documented in the Substantial Completion Inspection Report have

been corrected.2. All fixed equipment has been furnished, programmed and installed according to the

drawings and specifications.3. All portable equipment has been turned over to the Owner.




4. All equipment has been tested individually and as a completed assembly performs asspecified.

5. The Operations and Service Manual and As-Built Documentation have been completed,approved and delivered to the Owner.

3.09 DEMONSTRATIONA. General:

1. Notify the Owner’s Representative in writing that the system has met all of therequirements for Training and is ready for Training two weeks prior to Training.

2. Train the Owner after all of the deficiencies documented in the Substantial CompletionInspection have been corrected and observed by the Owner’s Representative.

3. Provide twenty four hours of hands-on training in practical operation of the system to theOwner. Include the following training topics:a. General sound, video and control system operation and theory.b. Signal topology for each system provided.c. Basic functionality.d. Correct operating procedures.e. DSP equipment software configuration and operation.f. Control system operation.g. Routine maintenance and upkeep.

4. Provide eight hours training for Owner's maintenance personnel including troubleshooting,servicing, and adjusting equipment and normal maintenance schedules.a. Engage a factory-authorized service representative to train Owner's maintenance

personnel.b. Submit all training materials to the Owners Representative for review prior to

scheduling training sessions.c. Use the reviewed final version of maintenance manuals as a training aid.d. Schedule training with Owner, with at least seven days' advance notice.

5. Videotape all of the training sessions. Provide three copies to the Owner on digital videodisk (DVD) format.

6. Attend the first 3 scheduled events to demonstrate the practical operation, setup andoperation of the system.

7. Provide 4 hours of follow-up training within 3 months of the initial training to review aspectsof the original training and provide instruction on specific troubleshooting issues.

3.10 PROTECTIONA. General:

1. After the audio-video system has been installed in the field, protect the audio-video systemfrom damage during construction. If damage occurs despite such protection, remove andreplace damaged components or entire unit as required to provide units in their original,undamaged condition.

2. Provide temporary covering of the audio-video system components until time ofSubstantial Completion.

3. See Part 1 if this Section for the Project Site Conditions requirements.END OF SECTION