18 hardware description modules - interactive productsitpg.com.au/image/data/ci1145 - hardware...

!"#$$%&"'

($

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18 Hardware description modules18.1 Master card E3X120The master card E3X... is contained in all CI1145 models.There are 3 types of master cards are available:

Master card Part. Nr. for FM installations for increasedpower supply

E3X120 511421 – –E3X120 (FM) 546632 ! –

E3X120 (P-FM) 559700 ! !

18.1.1 Features

Central processing unit for the fire detection control unit series CI1145 (CS1140) suppliedwith basic equipment, comprising:! Main processor! Battery charging unit max. 27Ah battery! Control outputs for alarm horns! Control outputs for fire control installations! Output contacts for remote transmission! Supply outputs 24VDC

! Connector for membrane keyboard (housing front panel)! Connector for max. 4 plug-in line cards and 1 RS232 module! Interfaces– C-Bus for external operating panel, Gateway etc.– E-Bus for max. 4 line cards K3M...– I-Bus for max. 4 optional I-Bus-modules E3M..., E3G..., E3L... etc.– Data Bus for parallel indicator panel B3R051 or K3R072 for synoptic panel or for relay

card K3G060! Integrated ground fault monitoring! Card format 205mm x 340mm

!"#$$%&"'

('

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.1.2 Key dataCurrent consumption– when operating on the mains (29.6V)– when operating on battery (24V)– maximum upon alarm (24V)

130mA + 100mA for LCD back lighting 1)120mA + 120mA for LCD back lighting 1)350mA (without external load + battery charge)

Monitored control line ’alarm horn’– Operating voltage in’normal operating condition’

– Operating voltage ’active phase’– Maximum current (active phase)– Line termination element– Active phase

2.3V (Open line > 3.5V /short circuit <1.0V)

24..30V (reversed polarity to ’active condition’)630mA (fuse ’F1/2’)Resistor 4k75Continuous signal / intermittent 1sec/1sec

Output contact remote transmission– max. load 1A/30VCombined driver outputs/control inputs– Application as ’control output’– Application as ’control input’

power rating up to 40mA (24V) short circuitvia dry contact

Connection ’Emergency power battery’– Type of battery– Charging characteristic

Lead batteries 2x12V / ...27Ah (fuses ’F6/7’)temperature compensation designed for ALARMCOM(FIAMM) batteries or equivalent

Supply outputs

– ’24V supply external’ (’K6’)– ’24V supply internal’ (’K4’)– 5V via ’K1’ (I-Bus modules)

NOTE: output monitoring possible, depending on parame-trization via AlgoWorks

max. 630mA / 1A (fuse ’F3’)max. 630mA / 1A (fuses ’F4/5’)max. 500mA

RAM– permanently soldered 8 x 128k x 8BitEPROM– pluggable at pos. ’D1’+’D2’ 2 x 512k x 8Bit (e.g. 27C4001)

1) The LCD back lighting is only active upon operation or alarm, additional 4mA for CI1145-2 for ’FBA’

Battery charging curves

ALARMCOM (FIAMM)

2.162.182.202.222.242.262.282.302.322.342.362.382.40

0 10 20 30 40 50Ua min. [V]Ua middle [V]Ua max. [V]

T [°C]

U [V]

!"#$

!"#%

!"!&

!"!!

!"!'

!"!$

!"!%

!"(&

!"(!

!"('

!"($

!"(%

!"'&

& #& !& (& '& )&

Genesis G12V120W15

Ua min. [V]

Ua max. [V]Ua mitte [V]

T [°C]

Power-Sonic PS12260

!"#$

!"#%

!"!&

!"!!

!"!'

!"!$

!"!%

!"(&

!"(!

!"('

!"($

!"(%

!"'&

& #& !& (& '& )&

Ua min. [V]

Ua max. [V]

U [V]

T [°C]

(at ! 40°C 100%battery chargingnot guaranteed)

Alternatives

U [V]

!"#$$%&"'

(C

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.1.3 Important components

E3X120

K5

K6 F5

F4 K7

K8

K9

K10

BR1BR3

BR2BR4

BR5BR6

K4

K3

K2

K1 F7

ST1S3

X30X60

V5

F6F3

F1F2

F8

V1

I-Bus 68

I-Bus 69V2

ST4

V10

V9

V8

V7

ST3

ST6

H1S1

H2H3

ON1

I-Bus 70V3

V4

I-Bus 71

X31

Y31

clock

EVEND2

ODDD1

H4H7

H5

K11K12

J1J2

J3

S2

1212

1

20

1

61

6

14

15

910

3031

1811

1231

13

14

31

1516

8

7

6

5

31

2428

1

253

2120

17

23

1922

294

227

26

50

G1

H6

1 ST1 Flat cable header (26-pin): I-Bus2 ST3 Connector: LCD illumination3 ST4 Connector: FBA key (only for CI1145-2 ’CH’)4 ST6 Flat cable header (Mini): RS232, maintenance PC, printer etc.

5 K1 Plug-in terminals: supply for the I-Bus modules6 K2 Plug-in terminals: input voltage 29.6V7 K3 Plug-in terminals: battery 24V8 K4 Plug-in terminals: output voltage for remote transmission9 K5 Plug-in terminals: C-Bus10 K6 Plug-in terminals: 24V external outputs 1 + 211 K7 Plug-in terminals: control lines for alarm horns 1 + 212 K8 Plug-in terminals: remote transmission fault and alarm13 K9 Plug-in terminals: data bus for parallel indicator panels or synoptic card

!"#$$%&"'

$@

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

14 K10 Plug-in terminals: control outputs/inputs15 K11 Plug-in terminals: operation enabled key switch16 K12 Plug-in terminals: door contact

17 V1-V4 Connector: for line cards18 V5 Connector: for RS232 card K3I06019 V7-V9 Connector: for membrane keyboard20 V10 Connector: for FBA membrane keyboard (only for CI1145-2 ’CH’)

21 50 Controller: FBA controller (only for CI1145-2 ’CH’)22 S1 Programming switch:

S1-1 on all inputs/outputs inactive

S1-2 on remote transmission (alarm + fault) and alarm hornsinactive

temporary service functions

S1-3S1-4S1-5

unused

S1-6 on control line alarm horns intermittent 1sec./1sec.S1-6 off control line alarm horns continuous signal

configuration

23 S2 Key: Reset CPU24 S3 Key: Battery ’start without mains’

25 G1 Lithium battery 3V / 70mAh: RAM buffering for clock, user data etc.– data storage time: minimum 2 weeks, typical >100 days– maintenance-free

26 D1/D2 EPROM plug in spaces

27 X31/Y31 Programming connector: EPROM size’X31’ plugged-in = EPROM size 512Kx8Bit (ex-works positioning)’Y31’ plugged-in = EPROM size 1024Kx8Bit

28 X30/X60 Programming connector: Ground fault monitoring’X60’ plugged-in = ground fault monitoring control unit active

disconnected= ground fault monitoring control unit inactive’X30’ on pos. ’J1’ = C-Bus not monitored for ground fault

on pos. ’J2’ = C-Bus monitored for ground fault,provided that ’X60’ is also active

29 H1..H7 Service-LEDs:’H1’ green not used’H2’ yellow all inputs/outputs inactive’H3’ yellow all remote transmission horns inactive’H4’ red fault remote transmission’H5’ red alarm horn 1’H6’ red alarm horn 2’H7’ red alarm remote transmission

30 BR1-6 Resistors to modify the C-Bus cable impedance:

Position Cable impedance of 110!, e.g. forG51 0.6Ø

Cable impedance of 50!" e.g. forMICC

BR5,6 402Ω 182ΩBR1,2,3,4 110Ω

inserted at factory49.9Ω

– A modification of impedance is in general only necessary if the C-Bus line is > 100m.– Specification of resistors for impedance values other than 110! or 50! " see document e1594

X31

Y31

X60

J1

J2

X30

J3

!"#$$%&"'

$"

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

31 Fuses

Master cardFuses Notes E3X120

Part.Nr. 511421E3X120 (FM)

Part. Nr. 546632E3X120 (P-FM)Part. Nr. 559700

F1 control line alarm horn 1 630mA/TF2 control line alarm horn 2 630mA/T

F3 24V supply remote transmission’internal’ 630mA/T 1A/T

F4/5 24V supply outputs 1/2 ’external’ 1) 1A/T

F6/7 battery 3,15A/T 6,3A/TF8 control outputs/inputs 1A/T

1) The rating of the fuses F3/4/5 can be increased from 630mA/T up to max. 1A/T(e.g. to provide 24V to printer B2Q191 etc.). The total current of the outputs K1, K4, K6, K7 and K10 mustnot exceed 1.7A.

!"#$$%&"'

$B

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.1.4 Connections

1234

++

1Plug-in terminals K1

24V5V

Supply for I-Bus modules to I-Bus modulesE3M.../E3L.../E3G... etc.

0V blueblue

green

red

12

+–


Input voltage29.6V " /2%

from converter B2F...0V

12

+–


Battery 24VF6

F7 battery 24V / ...27Ah

12

+–


Supply remote transmissionF3 to remote transmission equipment

1234


C-Bus B1A1

C-Bus (return line) B2A2

K7–1

K5–2K5–1K5–4K5–3

AlgoPilot B3Q...

1234

+–


Ext. Supply output 1

5+–

F4

F5K7–5K7–3

K7–4K7–6

1234

+–


Monitored control lineAlarm horn 1

+–

Monitored control lineAlarm horn 2

F1

F2

24V

external audible alarm devices

24V4.75kΩmax. 0.5A

max. 0.5A

123

Remote transmissionFAULT (LED H4)(Normal operation = 1/3 closed)

Plug-in terminals K8

456

Remote transmissionALARM (LED H7)

to remote transmission device

max.1A / 30V

123Data bus Parallel display B3R...

or Synoptic card K3R...

Plug-in terminals K9

456

(Clock)

(data)

(Load)

K2–2

K2–4K2–3

K2–5K2–6

K2–1

K1–3K1–2

K1–1

B3R051or K3R072max.1A / 30V

4.75kΩ

(Normal operation = 4/5 closed)

CI1145 (E3X120)

E3X120

K4K3K2K1

K5K6

K7K8

K9

Ext. Supply output 2

1) The indicated polarity at the terminals K7-1...4 applies to the active state

1)

!"#$$%&"'

$D

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

Flat cable header (Mini) ST6

20-p

inData communication RS232

according to application– Printer B2Q191– Maintenance PC (B3D021)– PSA/Pager interface K3I090

1234

––


Q1/I1Control outputs/inputs(as outputs max.40mA/24V)

––

5–6789

––

––

10–11121314

––

––

15–16171819

–+

20

0V

F8

Q2/I2Q3/I3Q4/I4Q5/I5Q6/I6Q7/I7Q8/I8Q9/I9

Q10/I10Q11/I11Q12/I12Q13/I13Q14/I14Q15/I15Q16/I16

relay function ’output’(location outside thehousing admissible)

signal transmitter (contact) function ’input’(location outside the housing admissible)

external key switch (optional)121

Plug-in terminals K11Operat. enabledC

Externally enabledoperation

door switch (optional)121

Plug-in terminals K12Inputdoor switch

Connector ST4

2-pi

n

FBA key FBA key

LCD to LCD illumination

Connector ST3

3-pi

n

Plug-in terminal block monitoredagainst removal

internal wiring

Z3B171141211

A1A2

10A 250VAC900Ω

Quiescent current 33mA at 29.6V(27mA at 24V)

CI1145 (E3X120)E3X120

ST4

ST6ST3

K10

K11K12

Flat cable header ST1

26-p

inData communicationI-Bus modules

to the I-Bus modules

!"#$$%&"'

$E

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.2 Line card ’interactive’ K3M071The line card K3M071 is not integrated into CI1145-x (supplied separately).

18.2.1 Overview

! Line card for 1 interactive detection line (stub or loop line)! Can be inserted in the E3X120 master card (E-Bus)! max. 4 x K3M071 possible! Card address (E-Bus) is given by the plug-on location! The detection line is galvanically isolated from the control unit! Integrated ground fault monitoring! Card format 151mm x 69mm

18.2.2 Key dataAddresses .... 128 1)Number of wires 2Cable type twistedLine resistance ....120 ! 1) 2)Line capacitance ....300nF 1) 2)

Line short circuit immunity yes (separator in each manual call point and input/output module, auto-matic detectors are available with or without separator)

T-branch yesQuiescent current at 24V(typical)

120mA for 128 detectors(53mA without detectors + 0.5mA per D-Bus device)

1) For limitations at ’acquisition level’ " see document e15082) with MICC max. 1000m from the control unit to the last detector, with RADOX max. 2000m


1

ST1

K1

15

2

3

K3M071

1 Connector ’ST1’ to plug into master card E3X120, connector ’V1....V4’ (E-Bus)2 Philips screw M3x83 2 spacer pins nylon

!"#$$%&"'

$#

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.2.4 Connections

K3M071Plug-in terminals K1

interactive detection lineloop or stub line

1+2345

–

+–

return with loopline

1

1 Connection of shielding if used (not essential)

!"#$$%&"'

$(

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.3 Line card ’collective’ K3M080The line card K3M080 is not integrated into CI1145-x (supplied separately).

18.3.1 Overview

! Line card for 4 collective detection lines (stub lines)! Can be inserted in the E3X120 master card (E-Bus)! max. 4 x K3M080 possible! Card address (E-Bus) is given by the plug-in location! Short circuit can be evaluated either as fault or alarm! Line termination with Transzorb or EOL22, depending on the type of line! 2 different types of line available (programmable via AlgoWorks) dependent on the de-

tector series connected! Card format 151mm x 69mm

18.3.2 Key dataLine type 1) Type 11 Type 1Detector series which can be connected DS11 / MS9 / 716 MS6/7 / 9 / 24 / (DS11)

for details " see chapter 18.3.5Number of detectors per line max. 25 2)Number of wires per line 2Cable type twisted (untwisted allowed)Line resistance max. 150! max. 250!Line capacitance max. 4"F max. 4"FLine termination element Transzorb 20V EOL22 (Ex)Line voltage see table ’Line voltage’ chapter 18.3.3

Alarm current limitation 45 – 60mA during AI pulsemax. 4.5mA during AI blank phase

Line voltage limitation 26.5 ... 27.7VLine current in ’quiescent condition’ max. 4.5mAReset time 3 Sec.Switch-on alarm delay period 4.6 Sec.Fault signal delay 15 Sec.Module quiescent current at 24V (typical) 48mA

1) When parameterizing the line types (SWE11) it must be known which detector series are being connected(K3M080 is supplied with 4 Transzorbs)

2) for limitations " see documents e825 and e1508

18.3.3 Line voltage

’Alarm’3.2 ... 16.4V

’Open line’23.3 – 27.7V

’Short circuit’0 – 3.7V

’Quiescent’17.3–24.1V

0 [V]

Line type 1

0 [V]

Line type 11

’Alarm’3.2 ... 16.4V

’Open line’21.4 – 27.7V

’Short circuit’0 – 3.7V

’Leak’ 15.7 – 18.0V

’Quiescent’18.9–22.2V

’Leak’ 15.7 – 19.7V

!"#$$%&"'

$$

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.3.4 Line termination elements

Transzorb (part number 460 051)

EOL22 (Ex) (part number 516 222)

18.3.5 Compatibility detectors ! line typeIncompatible– AT3– ATAN3– MS6 detectors– External response indicators with incandescent lamps– SE20 with incandescent lamp as response indicator– FES 7.5 detectors– 220V detectors

Line type 11" Line termination usingTranszorb 20VStandard application, also for Exdetectors via DC1192 or MLK20

Compatible detectorsAlgoRex detectors:DO110x , DT110x , DM110x, DC1192Older detectors:MS716 , MS9 , MLK20 , T2416/18 , D2417 , SE22, AT4x, AT5x without SE2Base: Z70, Z72, Z72A, Z74*, Z74A*, Z90, Z94, Z96*Limitations: Z74 and Z74A only as of year of construction 1988 (year index W)

D900 only as of year of construction 1983 (year index R)! if in doubt, use line type 1

Ex-detectors (without limitation)Operation via DC1192 with SB3: DO110x Ex, DT110x Ex(or via MLK20 with SB3) F911, D901, D921 with base Z91C/Z94C

D2401 Ex, S2406ExF6A Ex, D6A Ex

Line type 1" Line termination using EOL22(Ex)for older detectors and for mixedlines (new and older types of detec-tor)

Compatible detectorsAlgoRex detectors:DLO1191, (with mixed lines also DO110x, DT110x, DM110x, DC1192)Older detectors:MS6* , MS7*, MS9 , MS24 , SE20* , SE22 , MLK20, AT4x, AT5x, SE2Base electronics: Z70, Z72, Z72A, Z74, Z74A, Z90, Z94, Z96*Limitations: With MS6 and MS7 note the detector types or applications listed

under ’Incompatible’

!"#$$%&"'

$'

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"


K3M080

3

S1

ONST1

F1

K1

1

8

21

5

1

46

1 Fuse ’F1’ 1A/F for 5V supply (SMD fuse, can only be changed at factory)2 Connector ’ST1’ to plug into master card E3X120, connector ’V1....V4’ (E-Bus)3 Programming switch ’S1’:

Facilitates the classification of a line short circuit as a fault or as an alarm (collectivelyfor all 4 lines)S1 set to ”off” at factory

S1-1 not usedS1-2 on Short circuit evaluated as alarm (AI pulse generator active)S1-2 off Short circuit evaluated as fault

4 Philips screw M3x85 2 spacer pins nylon6 4 Transzorb

!"#$$%&"'

$C

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.3.7 Connections


Collective detection line 1 1+2345

–+–+

6–7+8–

Collective detection line 2



Line type 11 or 1

max.150Ω or 250Ω

*!"#$%&'($%))%*%&+,#-./+0%123!"#$%&'($%%%)%*%45!11%6478

Line type 11 or 1

Z-diode 5.6V

alarm contact*

1

Explosion hazard area

SB3

Ex detectors

MLK20

4k3

Line max. 20Ω24VDC

Explosion hazard area

SB3

Ex detectors

DC1192

EOL22 (Ex)

24VDC

Line type 11 or 1

Line type 11 or 1 *

*

2

3

3 3

4

4

*

1 Max. 25 collective DS11 detectors MS6, MS7, MS9, MS24 depending on type of de-tector, " see document e825

2 The 24V lead to the MLK20 may be max. 20Ω Important: Making current 0.5A (1 sec.)3 For details of max. permissible line resistance etc. " see document e1204 with latest

index4 Local compensating earth

!"#$$%&"'

'@

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.4 Line card ’AnalogPLUS’ K3M111The line card K3M111 is not integrated into CI1145-x (supplied separately).

18.4.1 Overview

! Line card for 4 AnalogPLUS detection lines (loop or stub lines)! Can be inserted in the E3X120 master card (E-Bus)! max. of 2 K3M111 line cards possible (but only 512 detectors permissible)! Card address (E-Bus) is given by the plug-in location! Card format 151mm x 138mm

18.4.2 Key dataAddresses per line .... 128 1)Number of wires 2Cable type twisted (untwisted allowed)Line resistance ....150 ! 1)Line capacitance ....300nF 1)

Line short-circuit immunity yes(separator in each detector, manual call point and input/output module)

Line topology Loop or stub line / T-tap via DC1135Quiescent current at 24V(typical)

238mA with 512 detectors(50mA without detectors + 0.31mA per D-Bus device)

1) for limitations at ’acquisition level’ " see document e15082) with MICC max. 1000m from the control unit to the last detector, with RADOX max. 2000m


3K1

K3M111

4

F1F2

ST11

2

1

20

1 Fuse ’F1’ 1A/T for 24V supplyFuse ’F2’ 1A/T for 5V supply

2 Connector ’ST1’ to plug into master card E3X120, connector ’V2,V3’ or ’V4’ (E-Bus)3 2 Philips screw M3x84 4 spacer pins nylon

!"#$$%&"'

'"

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.4.4 Connections


AnalogPLUS detection line 1loop or stub line

1+2345

–

+–return loop line


6+789

10

–

+–


11+12131415

–

+–


16+17181920

–

+–

return loop line

return loop line

return loop line

1

1 Connection of shielding if used (not essential)

!"#$$%&"'

'B

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.5 RS232 card K3I060The RS232 card K3I... is not integrated into CI1145-x (optional).

18.5.1 Overview

! For the conversion of the HCMOS level to RS232! Can be inserted in the E3X120 master module, connector ’V5’! Contains 2 serial RS232 interfaces! An interface with extended functions, e.g. for telephone modems! Both interfaces with galvanic isolation! Card format 55mm x 70mm

18.5.2 Key dataCurrent consumption 24V (from E3X120) 17mARate of transmission up to max. 19’200 baud


1

2

ST13

K3

K2

K3I060

15

13

1 Connector ’ST1’ to plug into master card E3X120, connector ’V5’2 Philips screw M3x83 2 spacer pins nylon

18.5.4 Connections

123

1234

(transmit) TXD(receive) RXD(ground) GND

RS232-1

RS232-2

K3I060Plug-in terminals K2

Plug-in terminals K3(transmit) TXD

(receive) RXDRTS

CTS(ground) GND 5

e.g. printer

!"#$$%&"'

'D

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.6 AC/DC Converter B2F020 / B2F040 / B2F060In each control unit CI1145-x a B2F040 or B2F020 is integrated, depending upon model.B2F060 use only to supply external devices such as door magnets etc. (optional).

18.6.1 Overview

! Converts the mains voltage to the system voltage! Built-in mains fuse (unscrew metal cover to exchange fuse)! Mains voltage 115/230VAC by means of internal connector (set at factory for 230VAC)! Requires no special cooling! Primary switched converter! Additional surge protector (mains side) only necessary in special cases! Current limitation and short circuit proof on the secondary side (parallel operation not

permissible, not even if de-coupled via diodes)! With metal shielding! Dimensions 210 x 98 x 40

18.6.2 Key dataB2F020 B2F040 B2F060

Mains voltage 115 / 230VAC +10%/–15%50...60Hz

115 / 230VAC +14%/–20% 1)50...60Hz

115 / 230VAC +14%/–20% 1)50...60Hz

Power consumption togetherwith control unit 40...220VA 30...200VA 30...120VA

Mains fuse internal 3.15A/T permanently inte-grated, not exchangeable on site internal 3A/T ’FS1’ internal 3A/T ’FS1’

Output current max. 6A continuous (limited) max. 3.5A continuous max. 4.5A continuousOutput voltage 29.6VDC +/− 2% 29.6VDC +/− 2% 24VDC +/− 2%Residual ripple max. 300mVpp max. 180mVpp max. 150mVppQuiescent current with bat-tery operation 0mA 0mA –

Temperature range 0°C .... +70°C without ventilator,automatic switch-off at >90°C –10°C .... +60°C max. 90% load 2) –10°C .... +60°C max. 90% load 2)

Standard CE / prEN54-4 CE / prEN54-4 CE / prEN54-4

1) VdS and FM approved +10% / –15%2) VdS approved 0°C .... 40°C

!"#$$%&"'

'E

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"


Note!Check mains voltage setting before commissioningThe converter is supplied by the factory at 230VAC. To switch over to 115VAC ! removemetal cover and then reinsert jumper at the ’115VAC’ pin.

Converter B2F020

115VAC

230VAC

12

34

56

2

7

DANGER!

1 Mounting flange2 Mounting screws for metal shield3 Clamp to fasten the mains cable4 Terminals ’L’/’N’/’E’: mains connection5 not used6 Terminals ’–’/’+’: load 24V7 Jumper for switchover 115VAC/230VAC

Converter B2F040/060

A

A115V

230VFS1

1

23

4

5

6

6

7

DANGER!

1 Jumper for switchover 115VAC/230VAC

2 Mains fuse ’FS1’ 3A/T3 Terminals ’L’/’N’/’G’: mains connection4 Protection for mains cable5 Terminals ’–COM’/’+V’: load 24V6 Installation openings7 Mounting screw and stud for metal cover

!"#$$%&"'

'#

)*+!,-,.!/0+*12,3+450/16.*!7!86,90*:5*8;,<!/=84:4;*!6,>+40? @$AB@@"

18.6.4 Connections

DANGER!Converter B2F... may only be built into housings which are not accessible to unauthori-zed persons.

Output voltage24VDC / max. 4.5A

Output voltage29.6VDC / max. 3.5A

Input voltage(115VAC) 230VAC / 50...60Hzmax. 120VA

Input voltage(115VAC) 230VAC / 50...60Hzmax. 200VA

mains

mainsNeutralGround

GroundNeutral

B2F040

GNL

COMCOM

93

93

:

:

FS1 Phase

B2F060

GNL

COMCOM

93

93

:

:

FS1 Phase

door magnet

B2F020

+–

ENLInput voltage

(115VAC) 230VAC / 50...60Hzmax. 220VA

Output voltage29.6VDC / max. 6A

OptSd–– S+ S+

Jumpers inserted at the factory (essential)

mainsGroundNeutralPhase

2K2

1to master card E3X120

2K2

1to master card E3X120

DANGER!

18 hardware description modules - interactive productsitpg.com.au/image/data/ci1145 - hardware...

Documents