18seer service manual

Technical Service Manual

R-410A Split System

18~22 SEER, Inverter Systems - 60 and 50 Hz

Single Split

June 2010

© 20 rane All rights reserved

Warnings, Cautions and Notices

Warnings, Cautions and Notices. Note that warnings, cautions and notices appear at appropriate intervals throughout this manual. Warnings are provide to alert installing contractors to potential hazards that could result in personal injury or death. Cautions are designed to alert personnel to hazardous situations that could result in personal injury, while notices indicate a situation that could result in equipment or property-damage-only accidents.

Your personal safety and the proper operation of this machine depend upon the strict observance of these precautions.

Important

Environmental Concerns!

Scientific research has shown that certain man-made chemicals can affect the earth's naturally occurring stratospheric ozone layer when released to the atmosphere. In particular, several of the identified chemicals that may affect the ozone layer are refrigerants that contain Chlorine, Fluorine and Carbon (CFCs) and those containing Hydrogen, Chlorine, Fluorine and Carbon (HCFCs). Not all refrigerants containing these compounds have the same potential impact to the environment. Trane advocates the responsible handling of all refrigerants-including industry replacements for CFCs such as HCFCs and HFCs.

Responsible Refrigerant Practices!

Trane believes that responsible refrigerant practices are important to the environment, our customers, and the air conditioning industry. All technicians who handle refrigerants must be certified. The Federal Clean Air Act (Section 608) sets forth the requirements for handling, reclaiming, recovering and recycling of certain refrigerants and the equipment that is used in these service procedures. In addition, some states or municipalities may have additional requirements that must also be adhered to for responsible management of refrigerants. Know the applicable laws and follow them.

�WARNING

Electrocution and Fire Hazards with Improperly Installed and Grounded

Field Wiring!

Improperly installed and grounded field wiring poses FIRE & ELECTROCUTION hazards. To avoid these hazards, you MUST follow requirements for field wiring installation and grounding as described in the National Electrical Codes (NEC) and your local/state electrical codes. All field wiring MUST be performed by qualified personnel. Failure to follow these requirements could result in death or serious injury.

ATTENTION: Warnings, Cautions and Notices appear at appropriate sections throughout this literature. Read these carefully.

� WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

�CAUTION: Indicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury. It could also be used to alert against unsafe practices.

NOTICE: Indicates a situation that could result in equipment or property-damage only accidents.

10 T

�WARNING

R410A Refrigerant under Higher Pressure than R22!

The units described in this manual use R410A refrigerant which operates at 50 to 70% higher pressures than R-22. Use only R-410A approved service equipment. Refrigerant cylinders are painted with "pink" color to indicate the type of refrigerant and may contain a "dip" tube to allow for charging of liquid refrigerant into the system. For specific handling concerns with R-410A, please contact your local Trane representative. Failure to use R-410A approved service equipment could result in standard equipment exploding under R-410A higher pressure which could result in death or serious injury.

NOTICE:

Use PVE Oil with R-410A Mini-Split Units!

All R-410A mini-splits use a PVE oil (Polyvinyl Ether Oil) that readily absorbs moisture from the atmosphere. To limit this “hygroscopic” action, the system should remain sealed whenever possible. If a system has been open to the atmosphere for more than 4 hours, the compressor oil must be replaced. Never break a vacuum with air and always change the driers when opening the system for component replacement. For specific handling concerns with PVE oil, contact your local Trane representative.

USE ONLY THE FACTORY RECOMMENDED - DAFNE HERMETIC OIL FV50S - for servicing these units.

5. 13

. 17. 17. 18

29

. 37. 37

. . 37

. . 37. . 39

. . . . 41

. . 43. . 43. . 46

. . 49

. . 49. . 54

System

System . 15

35

36

. . 19

4

Electrical Characteristics 16

Capacit Variation Ratio 14

60Hz Heat pump models

COOLING HEATING COOLING HEATING

3100/2637/1300 3250/2725/930 3100/2637/1300 3250/2725/93010600/9000/4435 11100/9300/3200 10600/9000/4435 11100/9300/3200

1050/660/180 1100/680/220 1050/630/180 1100/680/22016.8 17 6.5/5.8 6.8/6.122 9.8 22 9.8

Model of Indoor UnitFan Motor Speed (r/min) (SH/H/M/L) 1300/1060/920/740 1320/1200/1100/960 1300/1060/920/740 1320/1200/1100/960Output of Fan Motor (w)Fan Motor Capacitor (uF)Fan Motor RLA(A)Fan Type-PieceDiameter-Length (mm)EvaporatorPipe Diameter (mm)Row-Fin Gap(mm)Coil length (l) x height (H) x coil width (L)Swing Motor ModelOutput of Swing Motor (W)Fuse (A)Sound Pressure Level dB (A) (SH/H/M/L)Sound Power Level dB (A)(SH/H/M/L)***Dimension (W/H/D) ( mm)Dimension of Package (L/W/H) ( mm)Net Weight /Gross Weight (kg)Room Temp. sensorPipe Temp. sensorModel of Outdoor UnitCompressor Manufacturer/trademarkCompressor ModelCompressor TypeL.R.A. (A)Compressor RLA(A)Compressor Power Input(W)Overload ProtectorThrottling MethodStarting MethodWorking Temp Range ( ) 18 T 48 (-15) T 24 18 T 48 (-15) T 24CondenserPipe Diameter (mm)Rows-Fin Gap(mm)Coil length (l) x height (H) x coil width (L)Fan Motor Speed (rpm)Output of Fan Motor (W)Fan Motor RLA(A)Fan Motor Capacitor (uF)Air Flow Volume of Outdoor Unit m3/hFan Type-PieceFan Diameter (mm)Defrosting MethodClimate TypeIsolationMoisture ProtectionPermissible Excessive OperatingPressure for the Discharge Side(MPa)Permissible Excessive OperatingPressure for the Suction Side(MPa)Sound Pressure Level dB (A) (H/M/L)Sound Power Level dB (A) (H/M/L)Dimension (W/H/D) ( mm)Dimension of Package (L/W/H)( mm)Net Weight /Gross Weight (kg)Refrigerant Charge (kg)Temp.sensorPipe Temp. sensorDischarge sensor

Rated Voltage

15K20K

Model

15K20K

Indo

or u

nit

Frequency(Hz)

Dehumidifying Volume (l/h)Air Flow Volume (m3/h) (H/M/L)**

EER / C.O.P (W/W)

R410A / 1.215K20K

878X360X580 878X360X58036/41 36/41

63 63848X320X540

3.8

1.2 1.2

53 53

3.8

20K50K

848X320X540

R410A / 1.2

Auto defrost Auto defrost

IP24 IP24

T1 T1I I

Axial fan –1 Axial fan –1398.5 398.5

/ /1900 1900

40 400.17 0.17

608X508X44 608X508X44900 900

7 72-1.4 2-1.4

Transducer starting Transducer starting

Aluminum fin-copper tube Aluminum fin-copper tube

Int11l-3979 Int11l-3979Electronic Expansion Valve throttling Electronic Expansion Valve throttling

4.59 4.59800 800

Twin rotory Twin rotory33 33

SANYO SANYOC-6RZ110H1A C-6RZ110H1A

11/14 11/14

4TXK8509A9 4TXK8509A1

845×275×180 845×275×180915×255×355 915×255×355

38/34/30/26 38/34/30/2648/44/40/36 48/44/40/36

2.4 2.4PCB 3.15A Transformer 0.2A PCB 3.15A Transformer 0.2A

645X25.4X267 645X25.4X267MP24AA MP24AA

7 72-1.4 2-1.4

92 X 645 92 X 645Aluminum fin-copper tube Aluminum fin-copper tube

0.38 0.2Cross flow fan – 1 Cross flow fan – 1

20 204 1

0.84.0/4.0 4.2/4.0

4MXW8509A9 4MXW8509A1

0.8

4MXW8509A9 4TXK8509A9 4MXW8509A1 4TXK8509A1

115V 208-230V60Hz 60Hz

560/500/430/370 560/500/430/370

Function

Total Capacity (W) (High/Standard/Low *):Total Capacity (Btu/h) (High/ Standard/Low *):Power Input (W) (High/ Standard/Low *)Nominal Input Current (A)SEER/HSPF

15K

50K

Out

door

uni

t

5


4100/3458/1320 4200/3800/950 4100/3458/1320 4200/3800/95014000/11800/4500 14500/13100/3250 14000/11800/4500 14500/13100/3250

1450/990/120 1500/1190/220 1450/960/120 1500/1190/22017 18.2 7.0/6.3 7.5/6.820 9.6 20 9.6


T1Auto defrost

15K20K

Indo

or u

nit

I

15K

Auto defrostT1

20K

Axial fan –1398.5 398.5

1900 1900Axial fan –1

0.17 0.17/ /

900 90040 40

2-1.4 2-1.4747X508X44 747X508X44

Aluminum fin-copper tube Aluminum fin-copper tube9 9

Electronic Expansion Valve throttling Electronic Expansion Valve throttlingTransducer starting Transducer starting

800 800Int11l-3979 Int11l-3979

33 334.59 4.59

C-6RZ110H1A C-6RZ110H1ATwin rotory Twin rotory

4TXK8512A9 4TXK8512A1SANYO SANYO

915×255×355 915×255×35511/14 11/14

50/46/42/36 50/46/42/36845×275×180 845×275×180

PCB 3.15A Transformer 0.2A PCB 3.15A Transformer 0.2A40/36/32/26 40/36/32/26

MP24AA MP24AA2.4 2.4

2-1.4 2-1.4 645X25.4X267 645X25.4X267

Aluminum fin-copper tube Aluminum fin-copper tube7 7

Cross flow fan – 1 Cross flow fan – 192 X 645 92 X 645

4 10.38 0.2

4MXW8512A9 4MXW8512A1

20 20

1.4 1.43.5/3.2 3.6/3.2

60Hz 60Hz

510/470/430/370 510/470/430/370

4MXW8512A9 4TXK8512A9 4MXW8512A1 4TXK8512A1

115V 208-230V

SEER/HSPFAir Flow Volume (m3/h) (H/M/L)**

Total Capacity (W) (High/Standard/Low *):Total Capacity (Btu/h) (High/ Standard/Low *):Power Input (W) (High/ Standard/Low *)Nominal Input Current (A)

Model

EER / C.O.P (W/W)Dehumidifying Volume (l/h)

FunctionRated VoltageFrequency(Hz)

IIP24 IP24

1.2 1.2

3.8 3.8

6555

878X360X580 878X360X580848X320X540 848X320X540

50K 50K

15K 15KR410A / 1.3 R410A / 1.3

40/44 40/44

Out

door

uni

t

20K 20K

6


6550/5275/1750 7473/7327/1202 7325/6300/2812 7618/7560/126022350/18000/6000 25500/25000/4100 25000/21500/9600 26000/25800/4300

2650/1500/300 2750/2700/335 2650/1790/500 2750/2700/4007.67/6.94 14.06/12.72 9.15/8.28 14.06/12.72

18 10.5 18 10.1


15K20K

4MXW8524A1 4TXK8524A1FunctionRated Voltage 208-230V 208-230V

Model 4MXW8518A1 4TXK8518A1

Nominal Input Current (A)SEER/HSPFAir Flow Volume (m3/h) (H/M/L)**

60HzTotal Capacity (W) (High/Standard/Low *):Total Capacity (Btu/h) (High/ Standard/Low *):Power Input (W) (High/ Standard/Low *)

Frequency(Hz) 60Hz

850/780/650/550 900/800/700/600Dehumidifying Volume (l/h) 1.8 2

3.5/2.84MXW8518A1 4MXW8524A1

20 35

EER / C.O.P (W/W) 3.5/2.7

Indo

or u

nit

0.25

7

2.5

940X298X200

15K20K

0.451.5 2.5

98X710 98X765Cross flow fan – 1 Cross flow fan – 1

7Aluminum fin-copper tube Aluminum fin-copper tube

715X304.8X25.4 765X342.9X25.42-1.4 2-1.5

2.5MP28VB MP35XX

46/44/40/35 48/44/40/35PCB 3.15A Transformer 0.2A PCB 3.15A Transformer 0.2A

1008X315X21956/54/50/45 58/54/50/45

13/17 16/211010X285X380 1073X395X313

C-6RZ146H1ATwin rotory Twin rotory

4TXK8524A1SANYO SANYO

4TXK8518A1

C-6RZ146H1A

1640

418.4 8.441

1640

Electronic Expansion Valve throttling1NT11L-3979 1NT11L-3979


Transducer starting Transducer startingElectronic Expansion Valve throttling

2-1.47 7

690 780837x660x38.1 967x748x38.1

2-1.4

0.960 90

3200 42003 4

0.62

552Axial fan –1 Axial fan –1

T1 T1Auto defrost Auto defrost

520

IP24I I

1.2 1.2

3.8 3.8

IP24

6555

1030X460X735 1065X485X840890X700X340 920X790X370

R410A/1.45 R410A/1.8050/55 54/60

50K 50K

Out

door

uni

t

15K 15K20K 20K 7

60Hz Cooling only models4MYW8509A9 4TYK8509A9 4MYW8509A1 4TYK8509A1

COOLING COOLING 115V 208-230V60Hz 60Hz

3100/2637/1300 3100/2637/130010600/9000/4435 10600/9000/4435

1050/660/180 1050/630/18016.8 6.5/5.822 22

560/500/430/370 560/500/430/3700.8 0.84.0 4.2

Model of Indoor Unit 4MYW8509A9 4MYW8509A1Fan Motor Speed (r/min) (SH/H/M/L) 1300/1060/920/740 1300/1060/920/740Output of Fan Motor (w) 20 20Fan Motor Capacitor (uF) 4 1Fan Motor RLA(A) 0.38 0.2Fan Type-Piece Cross flow fan – 1 Cross flow fan – 1Diameter-Length (mm) 92 X 645 92 X 645Evaporator Aluminum fin-copper tube Aluminum fin-copper tubePipe Diameter (mm) 7 7Row-Fin Gap(mm) 2-1.4 2-1.4Coil length (l) x height (H) x coil width (L) 645X25.4X267 645X25.4X267Swing Motor Model MP24AA MP24AAOutput of Swing Motor (W) 2.4 2.4Fuse (A) PCB 3.15A PCB 3.15ASound Pressure Level dB (A) (SH/H/M/L) 38/34/30/26 38/34/30/26Sound Power Level dB (A) (SH/H/M/L)*** 48/44/40/36 48/44/40/36Dimension (W/H/D) ( mm) 845×275×180 845×275×180Dimension of Package (L/W/H) ( mm) 915×255×355 915×255×355Net Weight /Gross Weight (kg) 11/14 11/14Room Temp. sensor 15K 15KPipe Temp. sensor 20K 20KModel of Outdoor Unit 4TYK8509A9 4TYK8509A1Compressor Manufacturer/trademark SANYO SANYOCompressor Model C-6RZ110H1A C-6RZ110H1ACompressor Type Twin rotory Twin rotoryL.R.A. (A) 33 33Compressor RLA(A) 4.59 4.59Compressor Power Input(W) 800 800Overload Protector Int11l-3979 Int11l-3979Throttling Method Electronic Expansion Valve throttling Electronic Expansion Valve throttlingStarting Method Transducer starting Transducer startingWorking Temp Range ( ) 18 T 48 18 T 48Condenser Aluminum fin-copper tube Aluminum fin-copper tubePipe Diameter (mm) 7 7Rows-Fin Gap(mm) 2-1.4 2-1.4Coil length (l) x height (H) x coil width (L) 608X44X508 608X44X508Fan Motor Speed (rpm) 900/650 900/650Output of Fan Motor (W) 40 40Fan Motor RLA(A) 0.17 0.17Fan Motor Capacitor (uF) / /Air Flow Volume of Outdoor Unit m3/h 1900 1900Fan Type-Piece Axial fan –1 Axial fan –1Fan Diameter (mm) 398.5 398.5Defrosting Method / /Climate Type T1 T1Isolation I IMoisture Protection IP24 IP24Permissible Excessive OperatingPressure for the Discharge Side(MPa) 3.8 3.8

Permissible Excessive OperatingPressure for the Suction Side(MPa) 1.2 1.2

Sound Pressure Level dB (A) (H/M/L) 53 53Sound Power Level dB (A) (H/M/L) 63 63Dimension (W/H/D) ( mm) 848X320X540 848X320X540Dimension of Package (L/W/H)( mm) 878X360X580 878X360X580Net Weight /Gross Weight (kg) 36/41 36/41Refrigerant Charge (kg) R410A / 1.2 R410A / 1.2Temp.sensor 15K 15KPipe Temp. sensor 20K 20KDischarge sensor 50K 50K

Out

door

uni

t

SEER/HSPFAir Flow Volume (m3/h) (SH/H/M/L)**Dehumidifying Volume (l/h)EER / C.O.P (W/W)

Total Capacity (W) (High/Standard/Low *):Total Capacity (Btu/h) (High/ Standard/Low *):Power Input (W) (High/ Standard/Low *)Nominal Input Current (A)

ModelFunctionRated VoltageFrequency(Hz)

Indo

or u

nit

8

4MYW8512A9 4TYK8512A9 4MYW8512A1 4TYK8512A1COOLING COOLING

115V 208-230V60Hz 60Hz

4100/3458/1320 4100/3458/132014000/11800/4500 14000/11800/4500

1450/990/120 1450/960/12017 7.0/6.320 20

510/470/430/370 510/470/430/3701.2 1.23.5 3.6

Model of Indoor Unit 4MYW8512A9 4MYW8512A1Fan Motor Speed (r/min) (SH/H/M/L) 1300/1080/900/740 1300/1080/900/740Output of Fan Motor (w) 20 20Fan Motor Capacitor (uF) 4 1Fan Motor RLA(A) 0.38 0.2Fan Type-Piece Cross flow fan – 1 Cross flow fan – 1Diameter-Length (mm) 92 X 645 92 X 645Evaporator Aluminum fin-copper tube Aluminum fin-copper tubePipe Diameter (mm) 7 7Row-Fin Gap(mm) 2-1.4 2-1.4Coil length (l) x height (H) x coil width (L) 645X25.4X267 645X25.4X267Swing Motor Model MP24AA MP24AAOutput of Swing Motor (W) 2.4 2.4Fuse (A) PCB 3.15A PCB 3.15ASound Pressure Level dB (A) (SH/H/M/L) 40/36/32/26 40/36/32/26Sound Power Level dB (A) (SH/H/M/L)*** 50/46/42/36 50/46/42/36Dimension (W/H/D) ( mm) 845×275×180 845×275×180Dimension of Package (L/W/H) ( mm) 915×255×355 915×255×355Net Weight /Gross Weight (kg) 11/14 11/14Room Temp. sensor 15K 15KPipe Temp. sensor 20K 20KModel of Outdoor Unit 4TYK8512A9 4TYK8512A1Compressor Manufacturer/trademark SANYO SANYOCompressor Model C-6RZ110H1A C-6RZ110H1ACompressor Type Twin rotory Twin rotoryL.R.A. (A) 33 33Compressor RLA(A) 4.59 4.59Compressor Power Input(W) 800 800Overload Protector Int11l-3979 Int11l-3979Throttling Method Electronic Expansion Valve throttling Electronic Expansion Valve throttlingStarting Method Transducer starting Transducer startingWorking Temp Range ( ) 18 T 48 18 T 48Condenser Aluminum fin-copper tube Aluminum fin-copper tubePipe Diameter (mm) 9 9Rows-Fin Gap(mm) 2-1.4 2-1.4Coil length (l) x height (H) x coil width (L) 747X44X508 747X44X508Fan Motor Speed (rpm) 900/680 900/680Output of Fan Motor (W) 40 40Fan Motor RLA(A) 0.17 0.17Fan Motor Capacitor (uF) / /Air Flow Volume of Outdoor Unit m3/h 1900 1900Fan Type-Piece Axial fan –1 Axial fan –1Fan Diameter (mm) 398.5 398.5Defrosting Method / /Climate Type T1 T1Isolation I IMoisture Protection IP24 IP24Permissible Excessive OperatingPressure for the Discharge Side(MPa) 3.8 3.8


Sound Pressure Level dB (A) (H/M/L) 55 55Sound Power Level dB (A) (H/M/L) 65 65Dimension (W/H/D) ( mm) 848X320X540 848X320X540Dimension of Package (L/W/H)( mm) 878X360X580 878X360X580Net Weight /Gross Weight (kg) 41/44 41/44Refrigerant Charge (kg) R410A / 1.3 R410A / 1.3Temp.sensor 15K 15KPipe Temp. sensor 20K 20KDischarge sensor 50K 50K

ModelFunctionRated VoltageFrequency(Hz)Total Capacity (W) (High/Standard/Low *):Total Capacity (Btu/h) (High/ Standard/Low *):Power Input (W) (High/ Standard/Low *)Nominal Input Current (A)SEER/HSPFAir Flow Volume (m3/h) (SH/H/M/L)**Dehumidifying Volume (l/h)EER / C.O.P (W/W)

Indo

or u

nit

Out

door

uni

t

9

4MYW8518A1 4TYK8518A1 4MYW8524A1 4TYK8524A1COOLING COOLING208-230V 208-230V

60Hz 60Hz6550/5275/1750 7325/6300/2812

22350/18000/6000 25000/21500/96002650/1500/300 2650/1790/500

7.67/6.94 9.15/8.2818 18

850/780/650/550 950/800/700/6002 2.5

3.5 3.5Model of Indoor Unit 4MYW8518A1 4MYW8524A1Fan Motor Speed (r/min) (SH/H/M/L) 1350/1200/1050/900 1400/1150/1100/850Output of Fan Motor (w) 25 35Fan Motor Capacitor (uF) 1.5 2.5Fan Motor RLA(A) 0.25 0.45Fan Type-Piece Cross flow fan – 1 Cross flow fan – 1Diameter-Length (mm) 98X710 98X765Evaporator Aluminum fin-copper tube Aluminum fin-copper tubePipe Diameter (mm) 7 7Row-Fin Gap(mm) 2-1.4 2-1.5Coil length (l) x height (H) x coil width (L) 715X304.8X25.4 765X342.9X25.4Swing Motor Model MP28VB MP35XXOutput of Swing Motor (W) 2.5 2.5Fuse (A) PCB 3.15A Transformer 0.2A PCB 3.15A Transformer 0.2ASound Pressure Level dB (A) (SH/H/M/L) 46/44/40/35 48/44/40/35Sound Power Level dB (A) (SH/H/M/L)*** 56/54/50/45 58/54/50/45Dimension (W/H/D) ( mm) 940X298X200 1007X315X219Dimension of Package (L/W/H) ( mm) 1010X285X380 1073X395X313Net Weight /Gross Weight (kg) 13/17 16/21Room Temp. sensor 15K 15KPipe Temp. sensor 20K 20KModel of Outdoor Unit 4TYK8518A1 4TYK8524A1Compressor Manufacturer/trademark SANYO SANYOCompressor Model C-6RZ146H1A C-6RZ146H1ACompressor Type Twin rotory Twin rotoryL.R.A. (A) 41 41Compressor RLA(A) 8.4 8.4Compressor Power Input(W) 1640 1640Overload Protector 1NT11L-3979 1NT11L-3979Throttling Method Electronic Expansion Valve throttling Electronic Expansion Valve throttlingStarting Method Transducer starting Transducer startingWorking Temp Range ( ) 18 T 48 18 T 48Condenser Aluminum fin-copper tube Aluminum fin-copper tubePipe Diameter (mm) 7 7Rows-Fin Gap(mm) 2-1.4 2-1.4Coil length (l) x height (H) x coil width (L) 837x38.1x660 967x38.1x748Fan Motor Speed (rpm) 690/500 780/500Output of Fan Motor (W) 60 90Fan Motor RLA(A) 0.62 0.9Fan Motor Capacitor (uF) 3 4Air Flow Volume of Outdoor Unit m3/h 3200 4200Fan Type-Piece Axial fan –1 Axial fan –1Fan Diameter (mm) 520 552Defrosting Method / /Climate Type T1 T1Isolation I IMoisture Protection IP24 IP24Permissible Excessive OperatingPressure for the Discharge Side(MPa) 3.8 3.8


Sound Pressure Level dB (A) (H/M/L) 54 56Sound Power Level dB (A) (H/M/L) 64 66Dimension (W/H/D) ( mm) 890X340X700 920X370X790Dimension of Package (L/W/H)( mm) 1030X460X735 1065X485X840Net Weight /Gross Weight (kg) 50/55 54/60Refrigerant Charge (kg) R410A/1.45 R410A/1.80Temp.sensor 15K 15KPipe Temp. sensor 20K 20KDischarge sensor 50K 50K

ModelFunctionRated VoltageFrequency(Hz)Total Capacity (W) (High/Standard/Low *):

Out

door

uni

t

Air Flow Volume (m3/h) (SH/H/M/L)**Dehumidifying Volume (l/h)EER / C.O.P (W/W)

Indo

or u

nit

Total Capacity (Btu/h) (High/ Standard/Low *):Power Input (W) (High/ Standard/Low *)Nominal Input Current (A)SEER/HSPF

10

50Hz Heat pump modelsCOOLING HEATING COOLING HEATING

3100/2500/1180 3800/2750//1200 4000/3500/1220 4297/4000/131010600/9000/4036 13000/9386/4096 13714/12000/4172 14660/13650/4480

1330/730/280 1365/745/310 1560/1060/295 1420/1100/3306.1 6.3 7.0 7.217 9 17 9

3.2 3.4 3.2 3.4Model of Indoor UnitFan Motor Speed (r/min) (SH/H/M/L) 1260/1050/920/730 1320/1200/1100/950 1260/1070/900/730 1300/1150/1000/950Output of Fan Motor (w)Fan Motor Capacitor (uF)Fan Motor RLA(A)Fan Type-PieceDiameter-Length (mm)EvaporatorPipe Diameter (mm)Row-Fin Gap(mm)Coil length (l) x height (H) x coil width (L)Swing Motor ModelOutput of Swing Motor (W)Fuse (A)Sound Pressure Level dB (A) (SH/H/M/L)Sound Power Level dB (A) (SH/H/M/L)***Dimension (W/H/D) ( mm)Dimension of Package (L/W/H) ( mm)Net Weight /Gross Weight (kg)Room Temp. sensorPipe Temp. sensorModel of Outdoor UnitCompressor Manufacturer/trademarkCompressor ModelCompressor TypeL.R.A. (A)Compressor RLA(A)Compressor Power Input(W)Overload ProtectorThrottling MethodStarting MethodWorking Temp Range ( ) 18 T 48 (-15) T 24 18 T 48 (-15) T 24CondenserPipe Diameter (mm)Rows-Fin Gap(mm)Coil length (l) x height (H) x coil width (L)Fan Motor Speed (rpm)Output of Fan Motor (W)Fan Motor RLA(A)Fan Motor Capacitor (uF)Air Flow Volume of Outdoor Unit m3/hFan Type-PieceFan Diameter (mm)Defrosting MethodClimate TypeIsolationMoisture ProtectionPermissible Excessive OperatingPressure for the Discharge Side(MPa)Permissible Excessive OperatingPressure for the Suction Side(MPa)Sound Pressure Level dB (A) (H/M/L)Sound Power Level dB (A) (H/M/L)Dimension (W/H/D) ( mm)Dimension of Package (L/W/H)( mm)Net Weight /Gross Weight (kg)Refrigerant Charge (kg)Temp.sensorPipe Temp. sensorDischarge sensor

SEER/HSPFAir Flow Volume (m3/h) (H/M/L)**Dehumidifying Volume (l/h)EER / C.O.P (W/W)

Model 4MXW8509AB 4TXK8509AB

500/440/400/360

4MXW8509AB

FunctionRated VoltageTotal Capacity (W) (High/Standard/Low *):Total Capacity (Btu/h) (High/ Standard/Low *):Power Input (W) (High/ Standard/Low *)Nominal Input Current (A)

560/500/430/3800.8 1.4

4MXW8512AB 4TXK8512AB

220-240V 220-240V

10.1 0.25

4MXW8512AB

10 201

Aluminum fin-copper tube7 7

Cross flow fan – 1×596 92 X 645

Cross flow fan – 1

Aluminum fin-copper tube

581X264X25.4 645X25.4X2672-1.5 2-1.4

1.5 2.4MP24AA MP24AA

40/37/31/23 44/37/32/25PCB 3.15A PCB 3.15A

790×265×170 845×275×18050/47/41/33 54/47/42/35

9/12 10/13870×248×355 915×255×355

MITSUBISHI MITSUBISHI4TXK8509AB 4TXK8512AB

Single-rotary Single-rotaryKNB092FHBMC KNB092FHBMC

8.9 8.925 25

222KT-XH-2P-400mm 222KT-XH-2P-400mm895 895

Transducer starting Transducer startingCapillary throttling Capillary throttling

9.52 7Aluminum fin-copper tube Aluminum fin-copper tube

608X508X22 608x498x221-1.6 2-1.4

30 30830 880

2.5 20.3 0.3

Axial fan –1 Axial fan-11900 1900

Auto defrost Auto defrost400 400

I IT1 T1

1.2

3.8 3.8

IP24 IP24

15K20K

50K20K 20K15K 15K

R410A / 0.8

Indo

or u

nit

15K20K

35/40878X360X580848X260X540

6353

1.2

50K

Out

door

uni

t

R410A / 1.1536/41

878X360X580848X260X540

6252

11

12


6600/5275/1260 6800/5850/1120 7000/6450/1400 8200/7000/120022500/18000/4300 23200/20000/3800 24000/22000/4800 28000/24000/4100

2650/1600/380 2650/1620/350 2500/1985/350 2700/1930/35010.7 11.5 11.4 12.416.5 9 16 9

3.2 3.4 3.2 3.4Model of Indoor UnitFan Motor Speed (r/min) (SH/H/M/L) 1350/1200/1050/900 1420/1250/1150/1050 1250/1100/950/800 1300/1100/1000/850Output of Fan Motor (w)Fan Motor Capacitor (uF)Fan Motor RLA(A)Fan Type-PieceDiameter-Length (mm)EvaporatorPipe Diameter (mm)Row-Fin Gap(mm)Coil length (l) x height (H) x coil width (L)Swing Motor ModelOutput of Swing Motor (W)Fuse (A)Sound Pressure Level dB (A) (SH/H/M/L)Sound Power Level dB (A) (SH/H/M/L)***Dimension (W/H/D) ( mm)Dimension of Package (L/W/H) ( mm)Net Weight /Gross Weight (kg)Room Temp. sensorPipe Temp. sensorModel of Outdoor UnitCompressor Manufacturer/trademarkCompressor ModelCompressor TypeL.R.A. (A)Compressor RLA(A)Compressor Power Input(W)Overload ProtectorThrottling MethodStarting MethodWorking Temp Range ( ) 18 T 48 (-15) T 24 18 T 48 (-15) T 24CondenserPipe Diameter (mm)Rows-Fin Gap(mm)Coil length (l) x height (H) x coil width (L)Fan Motor Speed (rpm)Output of Fan Motor (W)Fan Motor RLA(A)Fan Motor Capacitor (uF)Air Flow Volume of Outdoor Unit m3/hFan Type-PieceFan Diameter (mm)Defrosting MethodClimate TypeIsolationMoisture ProtectionPermissible Excessive OperatingPressure for the Discharge Side(MPa)Permissible Excessive OperatingPressure for the Suction Side(MPa)Sound Pressure Level dB (A) (H/M/L)Sound Power Level dB (A) (H/M/L)Dimension (W/H/D) ( mm)Dimension of Package (L/W/H)( mm)Net Weight /Gross Weight (kg)Refrigerant Charge (kg)Temp.sensorPipe Temp. sensorDischarge sensor 50K 50K

20K 20K15K 15K

R410A/1.10 R410A/1.4047/52 50/55

1030X460X735 1030X460X735890X700X340 890X700X340

64 6454 54

1.21.2

3.83.8

IP24 IP24I I

T1 T1Auto defrost Auto defrost

520 520Axial fan –1 Axial fan –1

2700 32003 3

0.62 0.6260 60

690 690870x660x19.05 837x660x38.1

2-1.4 2-1.47 7


Transducer starting Transducer startingElectric expand valve Electric expand valve

1NT11L-3979 1NT11L-39791640 16408.4 8.441 41

Twin rotary Twin rotaryC-6RZ146H1A C-6RZ146H1A

Sanyo Sanyo4TXK8518AB 4TXK8524AB

20K 20K15K 15K

13/17 16/211010X285X380 1073X395X313940X298X200 1007X315X21956/54/50/45 61/57/52/4946/44/40/35 51/47/42/39

PCB 3.15A Transformer 0.2A PCB 3.15A Transformer 0.2A2.5 2.5

MP28VB MP35XX715X304.8X25.4 765X342.9X25.4

2-1.4 2-1.57 7

Aluminum fin-copper tube Aluminum fin-copper tube98X710 98X765

Cross flow fan – 1 Cross flow fan – 10.25 0.31.5 1.520 25

4MXW8518AB 4MXW8524AB

1.8 2850/780/650/550 900/800/700/550

220-240V 220-240V

Model 4MXW8518AB 4TXK8518AB 4MXW8524AB 4TXK8524AB

Indo

or u

nit

Out

door

uni

t

Dehumidifying Volume (l/h)EER / C.O.P (W/W)

Power Input (W) (High/ Standard/Low *)Nominal Input Current (A)SEER/HSPFAir Flow Volume (m3/h) (H/M/L)**

Rated VoltageTotal Capacity (W) (High/Standard/Low *):Total Capacity (Btu/h) (High/ Standard/Low *):

Function

60Hz Models

4MYW8509A94TYK8509A9






Length (m) 7.6 7.6 7.6 7.6 7.6 7.6Gas additionalcharge(g/m) 15 15 15 15 30 30

6(1/4”) 6(1/4”) 6(1/4”) 6(1/4”) 6(1/4”) 6(1/4”)9(3/8”) 9(3/8”) 9(3/8”) 9(3/8”) 12(1/2”) 16(5/8”)15 15 15 15 20 2030 30 30 30 40 40

Outer Diameter

Max Distance

Model

Con

nect

ion

Pipe

Length (m)Gas additionalcharge(g/m)

50Hz Models

66(1/4”)

Max Distance15 2030 40 40

201530

Outer Diameter6(1/4”) 6

12(1/2”) 12129.52(3/8”)

4MXW8524AB4TXK8524AB

Con

nect

ion

Pipe

5 5 5 5

15 15 20 50

Model 4MXW8509AB4TXK8509AB



13

*For 9/12 Mbh models:

*For 18/24 Mbh models:

14

INDOOR UNIT OUTDOOR UNIT

HEATEXCHANGE(EVAPORATOR)

HEATEXCHANGE(CONDENSER)

COMPRESSOR

GAS SIDE

3-WAY VALVE

LIQUID SIDE

2-WAY VALVE

COOLING

Accumlator

Discharge

Suction

Muffler

CapillaryStrainer Strainer

Strainer Strainer

INDOOR UNIT OUTDOOR UNIT

HEATEXCHANGE(EVAPORATOR)

HEATEXCHANGE(CONDENSER)

COMPRESSOR

GAS SIDE

3-WAY VALVE

LIQUID SIDE

3-WAY VALVE

COOLINGHEATING

Accumlator

Discharge

Suction

Muffler4-Way valve

Expansion Valve

15

Electrical Characteristics

60Hz Models

ModelIndoor Outdoor Hz Voltage Min. Max. MCA MFA W FLA

4MYW8509A9000AA 4TYK8509A9000AA 60Hz 115V 103V 127V 6.4 15 40 0.174MYW8512A9000AA 4TYK8512A9000AA 60Hz 115V 103V 127V 6.4 15 40 0.174MYW8509A1000AA 4TYK8509A1000AA 60Hz 220V 198V 242V 6.2 15 40 0.174MYW8512A1000AA 4TYK8512A1000AA 60Hz 220V 198V 242V 6.2 15 40 0.174MYW8518A1000AA 4TYK8518A1000AA 60Hz 220V 198V 242V 11.6 25 60 0.624MYW8524A1000AA 4TYK8524A1000AA 60Hz 220V 198V 242V 12.2 25 90 0.94MXW8509A9000AA 4TXK8509A9000AA 60Hz 115V 103V 127V 6.4 15 40 0.174MXW8512A9000AA 4TXK8512A9000AA 60Hz 115V 103V 127V 6.4 15 40 0.174MXW8509A1000AA 4TXK8509A1000AA 60Hz 220V 198V 242V 6.2 15 40 0.174MXW8512A1000AA 4TXK8512A1000AA 60Hz 220V 198V 242V 6.2 15 40 0.174MXW8518A1000AA 4TXK8518A1000AA 60Hz 220V 198V 242V 11.6 25 60 0.624MXW8524A1000AA 4TXK8524A1000AA 60Hz 220V 198V 242V 12.2 25 90 0.9

50Hz Models

ModelIndoor Outdoor Hz Voltage Min. Max. MCA MFA W FLA

4MXW8509AB000AA 4TXK8509AB000AA 50Hz 220V 198V 242V 11.6 25 30 0.34MXW8512AB000AA 4TXK8512AB000AA 50Hz 220V 198V 242V 11.8 25 30 0.34MXW8518AB000AA 4TXK8518AB000AA 50Hz 220V 198V 242V 9.8 15 60 0.624MXW8524AB000AA 4TXK8524AB000AA 50Hz 220V 198V 242V 11.7 25 60 0.62

Power Supply Current OFM

Power Supply Current OFM

16

60Hz Models

unit W(width) H(height) D(depth)4MYW8509A 845 275 1804MYW8512A 845 275 1804MYW8518A 940 298 2004MYW8524A 1007 315 219

50Hz Models

unit W(width) H(height) D(depth)4MYW8509A 790 265 1704MYW8512A 845 275 1804MYW8518A 940 298 2004MYW8524A 1007 315 219

Dimenssions(mm)

Dimenssions(mm)

17

Dimensions

90 700 34 396 518

Model

SUMMERIndoor conditions 25 30 35 40 45 50

Total Capacity (Btu/h) 9597 8993 8805 8041 8703 8304Sensible Capacity (Btu/h) 7543 7235 7109 6543 6355 6177

Input (W) 574 599 621 627 707 718Compressor Frequency (Hz) 41 41 41 41 41 41







WINTER12 D 7 D 4 D 0 D -4 D -7 D11 W 6 W 3 W -1 W -6 W -8 W

Total Capacity (Btu/h) 10850 10460 12170 12864 11347 9692Input (W) 700 656 831 1049 1057 1089

Compressor Frequency (Hz) 44 44 44 44 44 44Total Capacity (Btu/h) 10659 10180 11577 12105 10759 9343





22

15

18

20

OUTDOOR TEMPERATURE DRY

Indoor conditions

32 D 23 W

4MYW8509A1/4TYK8509A14MXW8509A1/4TXK8509A1

21 D 15 W

24 D 17 W

27 D 19 W


19

Model

















15

18

20

22

27 D 19 W

32 D 23 W


Indoor conditions


21 D 15 W

24 D 17 W

4MXW8509AB/4TXK8509AB

20

Model

















15

18

20

22

27 D 19 W

32 D 23 W


Indoor conditions



21 D 15 W

24 D 17 W

21

Model

















15

18

20

22

27 D 19 W

32 D 23 W


Indoor conditions



21 D 15 W

24 D 17 W

22

Model

















15

18

20

22

27 D 19 W

32 D 23 W


Indoor conditions



21 D 15 W

24 D 17 W

23

Model


Total Capacity (Btu/h)Sensible Capacity (Btu/h)

Input (W)Compressor Frequency (Hz) 59


Input (W)Compressor Frequency (Hz)

Total Capacity (Btu/h) 11800Sensible Capacity (Btu/h)

Input (W) 990Compressor Frequency (Hz)




Total Capacity (Btu/h)Input (W)

Compressor Frequency (Hz)Total Capacity (Btu/h)


Total Capacity (Btu/h) 13100Input (W) 1190



15

18

20

22

27 D 19 W

32 D 23 W


Indoor conditions



21 D 15 W

24 D 17 W

24

Model



Input (W)Compressor Frequency (Hz) 65








Total Capacity (Btu/h)Input (W)



Total Capacity (Btu/h) 25000Input (W) 2700



15

18

20

22

27 D 19 W

32 D 23 W


Indoor conditions



21 D 15 W

24 D 17 W

25

Model

















15

18

20

22

27 D 19 W

32 D 23 W


Indoor conditions



21 D 15 W

24 D 17 W

26

Model









Input (W) 65 65 65 65 65 65Compressor Frequency (Hz)








15

18

20

22

27 D 19 W

32 D 23 W


Indoor conditions



21 D 15 W

24 D 17 W

27

Model

















15

18

20

22

27 D 19 W

32 D 23 W


Indoor conditions



21 D 15 W

24 D 17 W

28

4MYW8509A9 4TYK8509A9

4MYW8509A1 4TYK8509A1

29

4MYW8512A9 4TYK8512A9

4 4MYW8512A1 4TYK8512A1

30

5 4MYW8518A1 4TYK8518A1

6 4MYW8524A1 4TYK8524A1

31

7 4MXW8509A9 4TXK8509A9

8 4MXW8509A1 4TXK8509A1

32

9 4MXW8512A9 4TXK8512A9

10 4MXW8512A1 4TXK8512A1

33

11 4MXW8518A1 4TXK8518A1

12 4MXW8524A1 4TXK8524A1

34

Sound Level Test condition

Test value

60Hz Models

Outdoor Indoor SH H M L1 4TYK8509A9 4MYW8509A9 38 34 30 262 4TYK8512A9 4MYW8512A9 40 36 32 263 4TYK8509A1 4MYW8509A1 38 34 30 264 4TYK8512A1 4MYW8512A1 40 36 32 265 4TYK8518A1 4MYW8518A1 46 44 40 356 4TYK8524A1 4MYW8524A1 48 44 40 357 4TXK8509A9 4MXW8509A9 38 34 30 268 4TXK8512A9 4MXW8512A9 40 36 32 269 4TXK8509A1 4MXW8509A1 38 34 30 26

10 4TXK8512A1 4MXW8512A1 40 36 32 2611 4TXK8518A1 4MXW8518A1 46 44 40 3512 4TXK8524A1 4MXW8524A1 48 44 40 35

50Hz Models

Outdoor Indoor SH H M L1 4TXK8509AB 4MXW8509AB 40 37 31 232 4TXK8512AB 4MXW8512AB 44 37 32 253 4TXK8518AB 4MXW8518AB 46 44 40 354 4TXK8524AB 4MXW8524AB 81 47 42 39

Model Indoor Sound Pressure level (dB(A))

ModelUnitNumber

Indoor Sound Pressure level (dB(A))

UnitNumber

36

Operating Functions

Operation of remote controller

Temperature parameters

• Room set temperature (T set)

• Room ambient temperature (T amb)

Fundamental functions

After powered on, no matter when the compressor is started, the time interval between two startups cannot be less than 3 minutes.

COOL mode

The condition and process of cooling

• If T amb is superior or equal T set, COOL mode will act, the compressor and outdoor fan will run, and the indoor fan will run at the set speed.

• If T amb is inferior or equal T set -2 ºC, the compressor will stop, the outdoor fan will delay 30 seconds to stop, and the indoor fan will run at the set speed.

• If T set -2ºC < T amb < Tset, the unit will keep running in the previous mode.

In this mode, the reversal valve will not be powered on and the temperature setting range is 16ºC~30ºC.

The unit will adjust the running frequency of the compressor automatically according to the change of ambient temperature.

Protection function

• Antifreezing protection

Under cooling and drying mode, after the compressor run about 10 mins, when the pipe temp.of the evaporator is to low, the compressor will stop, the outdoor fan will stop after 30s, under cooling mode the indoor fan and swing motor will keep running in the original mode, under drying mode the indoor fan will run at low fan speed, the swing motor will run in the original mode. When antifreezing protection is eliminated and the compressor has stopped for 3 minutes, the unit will resume running in the original mode.

TamdTset

Tset

3min

Compressor

Outdoor fanIndoor fan

Start cooling

Original running state

Stop cooling

Set fan speed

Run Stop

The period of antifreezing protection

Compressor

Outdoor fan

Indoor fan

3 min

Run Stop

37

Overcurrent protection

If total current is high, the compressor will run in limited or dropped frequency. When total current goes on rising over the stated value, the compressor will stop, the outdoor fan will delay 30 seconds to stop.

DRY mode

The condition and process of drying

• If T amb > T set, DRY mode will act, the indoor fan, outdoor fan and compressor will run, and indoor fan will run at low speed.

• If T set -2ºC inferior or equal T amb inferior or equal T set, the unit will keep running in the original mode.

• If T amb < T set -2ºC, the compressor will stop running, the outdoor fan will delay 30 seconds to stop and the indoor fan will run at low speed.

In this mode, the reversal valve will not be powered on and the temperature setting range is 16ºC~30ºC.


Protection

Protection is the same with that in COOL mode.

HEAT mode

The condition and process of heating

• If T amb inferior or equal T set +2ºC, HEAT mode will act, the compressor, outdoor fan and 4-way valve will run simultaneously, the indoor fan will delay at most for 2min to run.

• If T set +2ºC < Tamb < Tset +5ºC, the unit will keep running in the original mode.

• If T amb superior or equal T set +5ºC, the compressor will stop, the outdoor fan will delay 30 sec to stop and the indoor fan will blow for 60 sec at the original speed and then stop.

In this mode, the temperature setting range is 16ºC~30ºC.

The air conditioner will adjust the running frequency of the compressor automatically according to the change of ambient temperature.

When the unit is turned off in HEAT mode, or switched to other mode from HEAT mode, the four-way valve will be powered off 2min later after the compressor stops.

Dry mode will act

Running in the original mode

Stop running

Compressor

Outdoor fan

Indoor fan

Run Stop

Tamb

Tset

Tset-2

Low fan speed

38

The condition and process of defrosting

When frost is detected in the condenser, the system will enter into defrosting state. When defrosting starts, the compressor and indoor fan will stop, and the outdoor fan and four-way valve will delay 30 seconds to stop. The compressor will start again after 30s and. When the compressor has run for 8mins, the compressor will stop.

After 30 seconds the four-way valve opens and after another 60 seconds, the compressor and outdoor fan resume running. The indoor fan will delay 2 minutes to run at the latest and temperature on the display panel shows H1.

Under heating mode,when the compressor is stopped by malfunction, the indoor fan will blow at low fan speed for 60s and then stop.

Protection

• Overcurrent protection

If total current is high, the compressor will run in limited or dropped frequency. When total current go on rising over the stated value, the compressor will stop, the outdoor fan will delay 30 seconds to stop.

FAN mode

In this mode, the indoor fan will run the fan in High, Med, Low and Auto mode. The compressor, outdoor fan and four-way valve will stop.

In this mode, the temperature setting range is 16~30ºC.


AUTO mode

In this mode, the system selects COOL, HEAT and FAN mode automatically according to the change of ambient temperature. The protection function is the same with that of COOL/HEAT mode.


Other control

ON / OFF

Each time the On/Off button of the remote controller is pressed, the On/Off state will switch once.

MODE selection

Press the MODE button on the remote controller to select and display the following modes: AUTO, COOL, DRY, FAN, and HEAT.

Stop heating

Original running state

Reversal valve

Indoor fan

Outdoor fan

Stop

Start heating

Compressor

Tset

Tset Tamb 3min

Run

2min 2min

39

TEMP. setting button

Each time TEMP + or TEMP - button is pressed, the set temperature will be increased or decreased by 1ºC.

Adjusting range is 16~30ºC . In AUTO mode, this button does not function.

AUTO key

When the unit is stop, press AUTO key, the unit will run under AUTO mode and the swing motor starts.

When the unit is running, press AUTO key, the unit will be stopped.

Timer control

The unit is turned on or off according to the timer set by the remote controller.

Sleep control

When the air conditioner is in COOL or DRY mode, after Sleep mode has been set properly, the preset Tset will be increased by 1ºC after the sleep program has run for 1 hour, and Tset will be increased by another 1ºC after 2 hours. Tset has been increased by 2ºC total in two hours. Then the unit will run at this set temperature and at the set speed.

When the air conditioner is in HEAT mode, after Sleep mode has been set properly, the preset Tset will be decreased by 1ºC after the sleep program has run for 1 hour, and Tset will be decreased by another 1ºC after 2 hours. Tset has been increased by 2ºC totally in two hours. Then the unit will run at this set temperature and at the set speed.

In AUTO or FAN mode, the setting temp. will not change.

Handling switch

AUTO/STOP

Set temp.Tset

1 h 2 h Above 2h

Tset+2

Tset+1

Tset

1 h 2 h Above 2h

Tset

Tset-1

Tset-2 Set temp.Tset

40

Indoor fan control

Use the remote controller to set the indoor fan running at HIGH, MED or LOW speed. At this time the fan will run at high, medium or low speed. It can also be set to AUTO and the indoor fan will select fan speed(HIGH, MED or LOW) automatically according to ambient temperature.

There are at least 3 mins and 30s delay for fan speed shift.

Power supply for outdoor unit

The power supply for outdoor unit is turned on in AUTO, COOL, HEAT and DRY mode under turn-on state.

The power supply for outdoor unit will delay 3 minutes to turn off under turn-off state or in the FAN mode under turn-on state.

Swing control

Use the SWING button of the wireless remote control to control SWING On and Off. Swing will only act when indoor fan is running. After power on, the swing motor turns back to 0 position and closes the air outlet vent; if it does not preset swing, after the unit is turned on, it will turn to the max. air outlet D1 position; then turn back to L position under COOL mode.Under HEAT mode, the guide louver stays at D1; when in swinging state, it will swing between L1 and D1 position. When the unit is turned off, it will turn back to 0 position.

Buzzer control

When the unit is power on or receives remote control signal or the auto key be pressed, the buzzer will give out a beep.

Power-off memory function

Contents of memory: Mode; Swing; Set fan speed, Set temperature, Timing etc.

Under turn-on state, when power off and power on, the power supply for outdoor unit will be turn on after 3 mins.

Under turn-off state, when power off and power on, the power supply for outdoor unit will be turn on immediately.

Delay Protection of Compressor

Under COOL; DRY; HEAT mode, before each time the compressor starts, there will be 3 mins delay.

Common protection function in each mode

Overload protection

Ttube: at cooling,it detects the temp. of outdoor heat exchanger,at heating,it detects the temp. of indoor heat exchanger.

When Ttube is detected high, the compressor will run in limited frequency. When Ttube goes on rising over the stated value, the compressor will stop; under AUTO HEAT or HEAT mode, indoor fan will blow 60s at low fan speed and then stop; under other mode, the indoor fan will run at set speed.

41

Compressor discharge temperature protection

When discharge temperature is too high to over the stated value, the compressor will stop, and When discharge temp. resume normal and the compressor has stopped for 3 minutes, the unit will resume its original operating status.

Communication malfunction

When not receiving correct signal for 3 minutes, the unit has communication malfunction and the outdoor unit stops, it is the same as normal stop when meeting the set temp.

Module protection

When module is in protection, the compressor will stop, after the compressor has stopped for 3 minutes, it will resume to running. During module protection period, the indoor unit displays malfunction and the whole unit stops.

42

4. Remove front caseUnscrew the 6 tapping screws fixng the front panel and turn the front case backward to remove it.

5. Remove electric boxUnscrew the 2 screws fixing the electric boxPull out the wiring terminal of motor and then un-screw the 3 screws fixing electric box.Lift the ele-ctric box to remove it.

6. Remove evaporatorUnscrew the screws on the rear pipe cardplateand then remove the cardplate.

temp. sensorclasp

screw

clasp

screw

clasp

screw

44

7. Remove motor and cross flow fanUnscrew the screws fixing the motor press plateof motor and then the screws connecting the mo-tor and cross flow fan to separate and removethem.

screw

screw

screw

45

top cover

Cable Cross Plate sub-assy

cabinet

screws

front panel

screws

screws

1. Remove top cover and the Cable Cross Plate sub-assy Unscrew the screw on the handle and pull theCable Cross Plate sub-assy forcibly downwards to re-move it. Unscrew the 3 screws fixing the top cover toremove it.

2. Remove cabinetUnscrew the 4 screws fixing the cabinet to remove it.

3. Remove front panelUnscrew the 5 screws fixing the front panel andpull out the front panel to remove it.

Removal Procedure of Outdoor Unit

46

4. Remove electric box coverUnscrew the 2 screws fixing the electiric box. Pull theelectric box upwards and unplug the plug-inline to remove the electric box.

5. Remove axial flow fanUnscrew the nut and remove the washer fixing theaxial flow fan and then pull it out.

nut and washer

screws

axial flow fan

6.Remove 4-way valveWrap the 4-way valve with wet cloth and unsolderthe 4 weld spots of the 4-way valve to remove it.

weld spots

4-way valve

47

7. Remove electronic expannsion valveUnsolder the weld spots of eletronic expansionvalve connecting with other pipelines to remove it.

8. Remove gas valve and liquid valveUnscrew the 2 screws fixing the gas valve andunsolder the weld spots of gas valve and suctionpipe to remove the gas valve.Unscrew the 2 screws fixing the liquid valve andunsolder the weld spots of liquid valve and suc-tion pipe to remove the liquid valve.

screws

gas valve

electronic expannsion valve

liquid valve

9 . Remove compressorUnsolder the 2 weld spots of the compressor andunscrew the 3 feet nuts and remove the was-heres fixing the compressor to remove it.

compressor foot

48

Troubleshooting

�WARNING

Hazardous Service Procedures!

The maintenance and troubleshooting procedures recommended in this section of the manual could result in exposure to electrical, mechanical or other potential safety hazards. Always refer to the safety warnings provided throughout this manual concerning these procedures. Unless specified otherwise, disconnect all electrical power including remote disconnect and discharge all energy storing devices such as capacitors before servicing. Follow proper lockout/tagout procedures to ensure the power can not be inadvertently energized. When necessary to work with live electrical components, have a qualified licensed electrician or other individual who has been trained in handling live electrical components perform these tasks. Failure to follow all of the recommended safety warnings provided, could result in death or serious injury.

General Section

�WARNING

Hazardous Voltage!

Disconnect all electric power, including remote disconnects before servicing. Follow proper lockout/tagout procedures to ensure the power can not be inadvertently energized. Failure to disconnect power before servicing could result in death or serious injury.

Figure Air conditioner cannot start up

Airconditionercannotstart up

Breaker trippedor fuse burnt out

Air conditioner does not response after powered on. (The buzzer does not sound after the plug is connected and the unit does not response after the remote controller is used to turn it on)

When the breaker is set ON, it will trip at once

Remotecontroller does not receive signal (When powered on, the buzzer will send out a sound, unless it is broken)

When the unit is turned on, the breaker will trip in a few minutes

No power supply

The power plug is not or poorly connected

Controller fuse is burnt out

Loose or poor contact of transformer connection, or transformer malfunction

The controller is broken

Batteries of remote controller are low

Malfunction of remote controller

Loose or poor connection of receiving head

Receiving head is broken

Measure the insulating resistancefor grounding to confirm whether there is electrical leakage or short circuit in the unit

Insulation malfunction of line or componen in the air conditioner. Insulation breakdow occurs after radiation, which causes shor circuit or electricity leakage. Measure insulating resistance or use one-by-on elimination method; Malfunction of fuse. Replace it.

Check power supply circuit

Check and plug well plug, make loosen contact firm

Change control fuse

Secure the wire connection: measure the output voltage of the transformer and replace it if the value is wrong

Replace the controller

Change battery

First press the "AUTO" button of the manual switch. If there is no response, check according to the above method; if it is normal after the button is pressed, check if the installation location and wire connection of the receiving head are correct. If correct, replace the receiving head, or the remote controller.

1.

49

Figure Troubleshooting chart

Improper setting of temperature

Whether cooling (heating) loadis proper

Adjust the set temperature

Check the estimated load of cooling (heating)

Leakage or shortage of refrigerant

Leakage occurs between high and low pressure inside compressor

Malfunction of four-way valve

Partial blockage of capillary

Blockage of cooling system

Replace the compressor

Replace the four-way valve

Replace the capillary

Use the method of observing condensation on the evaporator and pressure value ofhigh pressure manometer to see whether the system is blocked and carry out corresponding handling on the system

Vacuumize after leakage detection and leakage repair. Charge refrigerant according to specification.

Malfunction of refrigerant flow

Poor thermal insulation of connecting pipe of indoor and outdoor unit

Ensure that both thick pipe and thin pipe are insulated well. The exposed part of the connector and copper pipe must be insulated as well.

Heat exchanger of outdoor unit is blocked

Air filters are blocked

Fan speed is set too slow

Fan speed turns low

Improper installation location for outdoor unit

Outdoor unit should be installed in a place with well ventilation

Set the fan speed to high or medium speed

Clean the filter

Clean the dust accumulated on the surface of the heat exchanger

Air circulation is insufficient

Damage ofcapacitor damaged

Damage of motor

Replace thecapacitor

Replace the motor

Flashing or awning can be installed appropriately. If the max. cooling capacity cannot be satisfied, replacement of the air conditioner is recommended.

Maintain a certain degree of indoor sealability. Try not to use appliance with high amount of heat.

Outdoor temperature is too high

Indoor sealability is inadequate; too many people go in and out frequently; there is heating unit in the room.

Poor

coo

ling

(hea

ting)

eff

ect

1.

50


When unit is cooling or heating, both compressor and outdoor fan don'trun

When unit is cooling or heating, the compressor runs but outdoor fan doesn't run

When cooling or heating, outdoor fan runs, but compressordoesn't run.

When cooling or heating, outdoor fan runs, but compressordoesn't run.

Fan doesn't run when FAN mode is set

Abnormal power supply of outdoor unit

Damage of outdoor main control board

Breakage of outdoor power module

Improper setting of temperature

Breakage of outdoor fan motor

Wrong wire connection

Breakage of outdoor main control board

Breakage of outdoor fan capacitor

Malfunction of compressor

Poor contact of connection between the main control board and module

Abnormal input of power module

Abnormal output of power module

Compressor temperature is too high

Wrong wiring

Damage of outdoor main control board

Check the circuit according to circuit diagram

Replace the main control board

Replace the power module

Adjust the set temperature

Replace the fan motor

Wire according to the circuit diagram

Replace the main control board

Replace the fan capacitor

Replace the compressor

Re-fasten the connection

Check if input is 320V. If not, replace the rectifier

Replace the power module

Cool the compressor for 30 min before running


Replace the outdoor main control board

Burn-out or broken wire of indoor fan motor

Wrong wiring

Circuit break or damage of fan motor capacitor

Repair or change the fan motor


Replace the indoor main control board

1.

51

Note: When replacing power module and rectifier, be sure to spread the radiating paste evenly.


Water leakage

Blockage or breakage of drainage hose

Wrap of refrigerant pipe connector is not tight enough

Fan of indoor unit contacts other parts

There is foreign substance in indoor unit

Compressor shakes too much

Touch of pipeline of outdoor unit

Touch of inner plates

Touch of outdoor unit fan blade with outer case

Abnormal sound inside compressor

Abnormal electromagnetic sound inside four-way valve when heating

Replace the drainage hose

Re-wrap and make it tight

Adjust fan location

Take out the foreign substance

Adjust support washer of the compressor and tighten loose bolts

Separate the touched pipeline

1. Tighten connecting screws 2.Stick shock-absorbing clay between plates

Adjust louver position

Replace compressor

Short circuit inside electromagnetic valve. Replace the electromagnetic valve

Abnormal sound and shake

1.

52

Figure Compressor is too hot

Compressor too hot,

Ambient temperature is too high For safe use

or directly under sunlightChange the mounting position

once, or the stop just start and stop at

often occur

Check whether the outdoor unit is not mountedproperly such as outlet blockage; bad ventilation

yes

no

yes

yes

yes

yes

yes

yes

yes

yes

yes

no

no

no

no

no

no

no

no

Clean themCheck if the filter or the outdoor condenser dirty

Check if the indoor and outdoor fans do not runor run too slowly and whether the outlet airflowis normal

Check if the cooling system blockage, the froston the capillary don't melt

Replace blockage component

Check if the power supply circuit for motor on the controller is normal or replace the motor

The power is abnormal Add voltahe regulator,etc.

Check if the system operating pressure is normal

1.6-2.4 MPa for heating system)

to confirm whether the refrigerant is leakage or mix with air (normal: 0.4-0.6MPa for cooling system, Recharge refrigerant

Check the breadboards of indoor and outdoor unitsand the power supply circuit assembly Change the assembly or main PCB

Change the power module

Change the compressor

Check the U ;V; W output of the outdoor powermodule for detail, see "Power Module protection"

Check if the compressor is jammed or the wire-wound resistance is open or short circuit

1.

53

YELLOW-LED4 GREEN-LED2 RED-LED3

55

18, 24 MBH - 60 and 50 Hz

56

4 E5 □ ■ □

5 E6 □ □ □

6 E8 ■ □ ■ ■

7 H6

8 C5

9 F1

10 F2

11 F3 □ □ ■

12 F4 □ □ □

13 F5 □ □

14 F6 ■ □

15 F8 ■ ■ □ ■

16 F9 ■ ■ □ □

17 PH □ ■ □ 57

protection

System Overloadoff 3s blink4 times

off 3s blink5 times

cooling, drying: compressorwill stop running, indoor fan is running.Heating: all will stop running cooling, drying: compressorwill stop running, indoor fan is running.Heating: all will stop running

Refer to malfunction analysis (overload, ,high temperature resistant)

Refer to malfunction analysis(IPM protection, compressor losessteps, compressor overcurrentprotection)

58

www.trane.com

For more information, contact your local Trane office or e-mail us at [email protected]

Literature Order Number

Date

Supersedes New

Trane has a policy of continuous product and product data improvement and reserves the right to change design and specifications without notice.

18seer service manual

Documents

8permissible excessive operatingpressure

permissible excessive operatingpressure

sensor 20k 20kmodel

seer hspfair flow volume

17fan motor capacitor

6m conditions ndoor

main control boardreplace

local trane representative