2 .875 spec
TRANSCRIPT
27802020183109702000
9/1/09
2-7/8” 10.40 lbs/ft X-95 with 2-3/8” HT SLH90 3-1/8” OD x 1.975” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade X-95 Connection 2-3/8” HT SLH90
Interchangeable With N/A Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.41 lbs/ft
Capacity 0.187 US gal/ft Displacement 0.158 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/8”
Inside Diameter 1.975” API Drift 1.850”
Rabbit OD, Suggested 1-13/16” Minimum Make-up Torque 3,200 ft-lbs
Maximum Recommend Make-up Torque 4,600 ft-lbs Torsional Yield Strength 7,600 ft-lbs
Tensile Strength (Torque Not Considered) 212,200 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 271,500 lbs 210,900 lbs Slip Crushing / Slip Type (SDML) 234,000 lbs 183,300 lbs
Burst Pressure 20,930 psi 19,140 psi Collapse Pressure 20,910 psi 18,010 psi
Torsional Yield Strength 14,600 ft-lbs 11,200 ft-lbs
Tool joint is weaker than tube in tension.
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040183109702000
9/1/09
2-7/8” 10.40 lbs/ft S-135 with 2-3/8” HT SLH90 3-1/8” OD x 1.975” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-3/8” HT SLH90
Interchangeable With N/A Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.41 lbs/ft
Capacity 0.187 US gal/ft Displacement 0.159 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/8”
Inside Diameter 1.975” API Drift 1.850”
Rabbit OD, Suggested 1.788” Minimum Make-up Torque 3,200 ft-lbs
Maximum Recommend Make-up Torque 4,600 ft-lbs Torsional Yield Strength 7,600 ft-lbs
Tensile Strength (Torque Not Considered) 212,200 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
NOTE: Tool joint is weaker in tension than tube.
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040183109702100
9/1/09
2-7/8” 10.40 lbs/ft Internal Coated S-135 with 2-3/8” HT SLH90 3-1/8” OD x 1.975” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-3/8” HT SLH90
Interchangeable With N/A Upset Type IU
Internal Coating TK 34 XT Nominal Weight 10.40 lbs/ft Adjusted Weight 10.41 lbs/ft
Capacity 0.187 US gal/ft Displacement 0.159 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/8”
Inside Diameter 1.975” API Drift 1.850”
Rabbit OD, Suggested 1.788” Minimum Make-up Torque 3,200 ft-lbs
Maximum Recommend Make-up Torque 4,600 ft-lbs Torsional Yield Strength 7,600 ft-lbs
Tensile Strength (Torque Not Considered) 212,200 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDXL) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040183105302207
9/1/09
2-7/8” 10.40 lbs/ft Internal Coated S-135 with 2-3/8 HT SL H90 3-3/8” OD x 1.813” ID Arnco 300 XT Hard Band Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection WT 23
Interchangeable With N/A Upset Type IU
Internal Coating TK 34 Tool Joint Hard Band Arnco 300 XT
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.98 lbs/ft
Capacity 0.186 US gal/ft Displacement 0.163 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-3/8”
Inside Diameter 1.813” API Drift 1.688”
Rabbit OD, Suggested 1.625” Minimum Make-up Torque 4,200 ft-lbs
Maximum Recommend Make-up Torque 6,300 ft-lbs Torsional Yield Strength 10,600 ft-lbs
Tensile Strength (Torque Not Considered) 269,400 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDXL) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Tube weaker than connection in tension. Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802010079107502000
9/1/09
2-7/8” 10.40 lbs/ft E-75 with 2-7/8” PAC 3-1/8” OD x 1-1/2” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade E-75 Connection 2-7/8” PAC
Interchangeable With N/A Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.51 lbs/ft
Capacity 0.183 US gal/ft Displacement 0.160 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/8”
Inside Diameter 1-1/2” API Drift 1-3/8”
Rabbit OD, Suggested 1-5/16” Minimum Make-up Torque 3,400 ft-lbs
Maximum Recommend Make-up Torque 3,800 ft-lbs Torsional Yield Strength 5,700 ft-lbs
Tensile Strength (Torque Not Considered) 273,000 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 214,300 lbs 166,500 lbs Slip Crushing / Slip Type (SDML) 184,800 lbs 144,700 lbs
Burst Pressure 16,530 psi 15,110 psi Collapse Pressure 16,510 psi 14,220 psi
Torsional Yield Strength 11,500 psi 8,900 psi
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802020079107502000
9/1/09
2-7/8” 10.40 lbs/ft X-95 with 2-7/8” PAC 3-1/8” OD x 1-1/2” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade X-95 Connection 2-7/8” PAC
Interchangeable With N/A Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.51 lbs/ft
Capacity 0.183 US gal/ft Displacement 0.160 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/8”
Inside Diameter 1-1/2” API Drift 1-3/8”
Rabbit OD, Suggested 1-5/16” Minimum Make-up Torque 3,400 ft-lbs
Maximum Recommend Make-up Torque 3,800 ft-lbs Torsional Yield Strength 5,700 ft-lbs
Tensile Strength (Torque Not Considered) 273,000 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 271,500 lbs 210,900 lbs Slip Crushing / Slip Type (SDML) 234,000 lbs 183,300 lbs
Burst Pressure 20,930 psi 19,140 psi Collapse Pressure 20,910 psi 18,010 psi
Torsional Yield Strength 14,600 ft-lbs 11,200 ft-lbs
Tool joint is weaker than tube in tension.
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802030079107502000
9/1/09
2-7/8” 10.40 lbs/ft G-105 with 2-7/8” PAC 3-1/8” OD x 1-1/2” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade G-105 Connection 2-7/8” PAC
Interchangeable With N/A Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.51 lbs/ft
Capacity 0.183 US gal/ft Displacement 0.160 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/8”
Inside Diameter 1-1/2” API Drift 1-3/8”
Rabbit OD, Suggested 1-5/16” Minimum Make-up Torque 3,400 ft-lbs
Maximum Recommend Make-up Torque 3,800 ft-lbs Torsional Yield Strength 5,700 ft-lbs
Tensile Strength (Torque Not Considered) 273,000 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 300,100 lbs 233,100 lbs Slip Crushing / Slip Type (SDML) 258,700 lbs 202,600 lbs
Burst Pressure 23,140 psi 21,150 psi Collapse Pressure 23,110 psi 19,910 psi
Torsional Yield Strength 16,200 ft-lbs 12,400 ft-lbs
Tool joint is weaker than tube in tension.
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040079107502000
9/1/09
2-7/8” 10.40 lbs/ft S-135 with 2-7/8” PAC 3-1/8” OD x 1-1/2” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-7/8” PAC
Interchangeable With N/A Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.51 lbs/ft
Capacity 0.183 US gal/ft Displacement 0.160 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/8”
Inside Diameter 1-1/2” API Drift 1-3/8”
Rabbit OD, Suggested 1-5/16” Minimum Make-up Torque 3,400 ft-lbs
Maximum Recommend Make-up Torque 3,700 ft-lbs Torsional Yield Strength 3,800 ft-lbs
Tensile Strength (Torque Not Considered) 273,000 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Tool joint is weaker in tension than tube.
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040079107102000
9/1/09
2-7/8” 10.40 lbs/ft S-135 with 2-7/8” PAC 3-1/8” OD x 1-1/4” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-7/8” PAC
Interchangeable With N/A Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.62 lbs/ft
Capacity 0.182 US gal/ft Displacement 0.162 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/8”
Inside Diameter 1-1/4” API Drift 1-1/8”
Rabbit OD, Suggested 1-1/16” Minimum Make-up Torque 4,100 ft-lbs
Maximum Recommend Make-up Torque 4,500 ft-lbs Torsional Yield Strength 6,800 ft-lbs
Tensile Strength (Torque Not Considered) 337,800 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Tool joint is weaker in tension than tube.
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040179103202007
9/1/09
2-7/8” 10.40 lbs/ft S-135 with 2-7/8 HT PAC 3-3/8” OD x 1-5/16” ID Arnco 300 XT Hard Band Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-7/8 HT PAC
Interchangeable With N/A Upset Type IU
Tool Joint Hard Band Arnco 300 XT Nominal Weight 10.40 lbs/ft Adjusted Weight 10.88 lbs/ft
Capacity 0.181 US gal/ft Displacement 0.166 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-3/8”
Inside Diameter 1-5/16” API Drift 1-3/16”
Rabbit OD, Suggested 1-1/16” Minimum Make-up Torque 4,200 ft-lbs
Maximum Recommend Make-up Torque 6,300 ft-lbs Torsional Yield Strength 10,600 ft-lbs
Tensile Strength (Torque Not Considered) 322,700 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in 2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Connection weaker than tube in tension. Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040179103502007
9/1/09
2-7/8” 10.40 lbs/ft S-135 with 2-7/8 HT PAC 3-3/8” OD x 1-1/2” ID Arnco 300 XT Hard Band Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-7/8 HT PAC
Interchangeable With N/A Upset Type IU
Tool Joint Hard Band Arnco 300 XT Nominal Weight 10.40 lbs/ft Adjusted Weight 10.53 lbs/ft
Capacity 0.183 US gal/ft Displacement 0.161 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-3/8”
Inside Diameter 1-1/2” API Drift 1-3/8”
Rabbit OD, Suggested 1-5/16” Minimum Make-up Torque 3,500 ft-lbs
Maximum Recommend Make-up Torque 5,200 ft-lbs Torsional Yield Strength 8,700 ft-lbs
Tensile Strength (Torque Not Considered) 273,000 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in 2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Connection weaker than tube in tension. Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040179105502100
9/1/09
2-7/8” 10.40 lbs/ft Internal Coating S-135 with 2-7/8” HT PAC 3-1/4” OD x 1-1/2” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-7/8” HT PAC
Interchangeable With N/A Upset Type IU
Internal Coating TK34XT Nominal Weight 10.40 lbs/ft Adjusted Weight 10.70 lbs/ft
Capacity 0.182 US gal/ft Displacement 0.164 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/4”
Inside Diameter 1-1/2” API Drift 1-3/8”
Rabbit OD, Suggested 1-5/16” Minimum Make-up Torque 3,500 ft-lbs
Maximum Recommend Make-up Torque 5,700 ft-lbs Torsional Yield Strength 8,600 ft-lbs
Tensile Strength (Torque Not Considered) 273,000 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 28,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040179107502207
9/1/09
2-7/8” 10.40 lbs/ft Internal Coated S-135 with 2-7/8” HT PAC 3-1/8” OD x 1-1/2” ID Arnco 300 XT Hard Band Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-7/8” HT PAC
Interchangeable With N/A Upset Type IU
Internal Coating TK 34 Tool Joint Hard Band Arnco 300 XT
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.53 lbs/ft
Capacity 0.183 US gal/ft Displacement 0.161 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/8”
Inside Diameter 1-1/2” API Drift 1-3/8”
Rabbit OD, Suggested 1-5/16” Minimum Make-up Torque 3,400 ft-lbs
Maximum Recommend Make-up Torque 5,100 ft-lbs Torsional Yield Strength 8,500 ft-lbs
Tensile Strength (Torque Not Considered) 273,000 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Tube weaker than connection in tension. Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802010003111602000
9/1/09
2-7/8” 10.40 lbs/ft E-75 with 2-7/8” RFO 3-7/8” OD x 2-5/32” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade E-75 Connection 2-7/8” RFO
Interchangeable With 2-7/8” OH Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.06 lbs/ft
Capacity 0.189 US gal/ft Displacement 0.166 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-7/8” Inside Diameter 2-5/32”
API Drift 1.963” Rabbit OD, Suggested 1-7/8”
Minimum Make-up Torque 5,300 ft-lbs Maximum Recommend Make-up Torque 5,800 ft-lbs
Torsional Yield Strength 8,800 ft-lbs Tensile Strength (Torque Not Considered) 347,700 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 214,300 lbs 166,500 lbs Slip Crushing / Slip Type (SDML) 184,800 lbs 144,700 lbs
Burst Pressure 16,530 psi 15,110 psi Collapse Pressure 16,510 psi 14,220 psi
Torsional Yield Strength 11,600 ft-lbs 8,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802020003111602000
9/1/09
2-7/8” 10.40 lbs/ft X-95 with 2-7/8” RFO 3-7/8” OD x 2-5/32” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade X-95 Connection 2-7/8” RFO
Interchangeable With 2-7/8” OH Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.06 lbs/ft
Capacity 0.189 US gal/ft Displacement 0.166 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-7/8” Inside Diameter 2-5/32”
API Drift 1.963” Rabbit OD, Suggested 1-7/8”
Minimum Make-up Torque 5,300 ft-lbs Maximum Recommend Make-up Torque 5,800 ft-lbs
Torsional Yield Strength 8,800 ft-lbs Tensile Strength (Torque Not Considered) 347,700 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 271,500 lbs 210,900 lbs Slip Crushing / Slip Type (SDML) 234,000 lbs 183,300 lbs
Burst Pressure 20,930 psi 19,140 psi Collapse Pressure 20,910 psi 18,010 psi
Torsional Yield Strength 14,600 ft-lbs 11,200 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802030003111602000
9/1/09
2-7/8” 10.40 lbs/ft G-105 with 2-7/8” RFO 3-7/8” OD x 2-5/32” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade G-105 Connection 2-7/8” RFO
Interchangeable With 2-7/8” OH Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.06 lbs/ft
Capacity 0.189 US gal/ft Displacement 0.166 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-7/8” Inside Diameter 2-5/32”
API Drift 1.963” Rabbit OD, Suggested 1-7/8”
Minimum Make-up Torque 5,300 ft-lbs Maximum Recommend Make-up Torque 5,800 ft-lbs
Torsional Yield Strength 8,800 ft-lbs Tensile Strength (Torque Not Considered) 347,700 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 300,100 lbs 233,100 lbs Slip Crushing / Slip Type (SDML) 258,700 lbs 202,600 lbs
Burst Pressure 23,140 psi 21,150 psi Collapse Pressure 23,110 psi 19,910 psi
Torsional Yield Strength 16,200 ft-lbs 12,400 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040003111602000
9/1/09
2-7/8” 10.40 lbs/ft S-135 with 2-7/8” RFO 3-7/8” OD x 2-5/32” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-7/8” RFO
Interchangeable With 2-7/8” OH Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.06 lbs/ft
Capacity 0.189 US gal/ft Displacement 0.166 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-7/8” Inside Diameter 2-5/32”
API Drift 1.963” Rabbit OD, Suggested 1-7/8”
Minimum Make-up Torque 5,300 ft-lbs Maximum Recommend Make-up Torque 5,800 ft-lbs
Torsional Yield Strength 8,800 ft-lbs Tensile Strength (Torque Not Considered) 347,700 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040003111603000
9/1/09
2-7/8” 10.40 lbs/ft S-135 with 2-7/8” RFO Class 2 3-7/8” OD x 2-5/32” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-7/8” RFO
Interchangeable With 2-7/8” OH Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.06 lbs/ft
Capacity 0.189 US gal/ft Displacement 0.166 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-7/8” Inside Diameter 2-5/32”
API Drift 1.963” Rabbit OD, Suggested 1-7/8”
Minimum Make-up Torque 5,300 ft-lbs Maximum Recommend Make-up Torque 5,800 ft-lbs
Torsional Yield Strength 8,800 ft-lbs Tensile Strength 347,700 lbs
TUBE DATA
New Class 2 Outside Diameter 2.875 in 2.658 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.253 in
Cross Sectional Area 2.858 in2 1.914 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 258,400 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 225,400 lbs
Burst Pressure 29,750 psi 23,800 psi Collapse Pressure 29,720 psi 23,290 psi
Torsional Yield Strength 20,800 ft-lbs 13,300 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040003141603000
9/1/09
2-7/8” 10.40 lbs/ft S-135 with 2-7/8” RFO Class 2 3-1/2” OD x 2-5/32” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-7/8” RFO
Interchangeable With 2-7/8” OH Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.06 lbs/ft
Capacity 0.189 US gal/ft Displacement 0.166 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-1/2” Inside Diameter 2-5/32”
API Drift 1.963” Rabbit OD, Suggested 2-7/8”
Minimum Make-up Torque 3,300 ft-lbs Maximum Recommend Make-up Torque 3,600 ft-lbs
Torsional Yield Strength 5,500 ft-lbs Tensile Strength (Torque Not Considered) 390,300 ft-lbs
TUBE DATA
New Class 2 Outside Diameter 2.875 in 2.658 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.253 in
Cross Sectional Area 2.858 in2 1.914 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 258,400 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 225,400 lbs
Burst Pressure 29,750 psi 23,800 psi Collapse Pressure 29,720 psi 23,290 psi
Torsional Yield Strength 20,800 ft-lbs 13,300 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040096111602000
9/1/09
2-7/8” 10.40 lbs/ft S-135 with 2-7/8 American Open Hole 3-7/8” OD x 2-5/32” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection 2-7/8” AOH
Interchangeable With N/A Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.98 lbs/ft
Capacity 0.187 US gal/ft Displacement 0.167 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-7/8”
Inside Diameter 2-5/32” API Drift 2-1/32”
Rabbit OD, Suggested 1-31/32” Minimum Make-up Torque 5,200 ft-lbs
Maximum Recommend Make-up Torque 5,700 ft-lbs Torsional Yield Strength 8,700 ft-lbs
Tensile Strength (Torque Not Considered) 337,100 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in 2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040323103702207
9/2/09
2-7/8” 10.40 lbs/ft Internal Coated S-135 with Hydril Wedge Thread 23 3-3/8” OD x 1-1/2” ID Arnco 300 XT Hard Band Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection Hydril WT 23
Interchangeable With N/A Upset Type IU
Internal Coating TK 34 Tool Joint Hard Band Arnco 300 XT
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.98 lbs/ft
Capacity 0.132 US gal/ft Displacement 0.116 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-3/8”
Inside Diameter 1-1/2” API Drift 1-3/8”
Rabbit OD, Suggested 1-1/4” Minimum Make-up Torque 2,200 ft-lbs
Maximum Recommend Make-up Torque 8,300 ft-lbs Torsional Yield Strength 10,400 ft-lbs
Tensile Strength (Torque Not Considered) 387,100 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in 2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040323105702207
9/2/09
2-7/8” 10.40 lbs/ft Internal Coated S-135 with Hydril Wedge Thread 23 3-1/8” OD x 1-1/2” ID Arnco 300 XT Hard Band Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection WT 23
Interchangeable With N/A Upset Type IU
Internal Coating TK 34 Tool Joint Hard Band Arnco 300 XT
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.98 lbs/ft
Capacity 0.132 US gal/ft Displacement 0.116 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/8”
Inside Diameter 1-1/2” API Drift 1-3/8”
Rabbit OD, Suggested 1-5/16” Minimum Make-up Torque 2,200 ft-lbs
Maximum Recommend Make-up Torque 8,300 ft-lbs Torsional Yield Strength 10,400 ft-lbs
Tensile Strength (Torque Not Considered) 387,100 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDXL) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802010026101502000
9/2/09
2-7/8” 10.40 lbs/ft E-75 with NC 26 3-5/8” OD x 1-3/4” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade E-75 Connection NC 26
Interchangeable With 2-3/8” IF Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.79 lbs/ft
Capacity 0.185 US gal/ft Displacement 0.165 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-5/8” Inside Diameter 1-3/4”
API Drift 1-5/8” Rabbit OD, Suggested 1-9/16”
Minimum Make-up Torque 4,250 ft-lbs Maximum Recommend Make-up Torque 4,700 ft-lbs
Torsional Yield Strength 7,100 ft-lbs Tensile Strength (Torque Not Considered) 313,700 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 214,300 lbs 166,500 lbs Slip Crushing / Slip Type (SDML) 184,800 lbs 144,700 lbs
Burst Pressure 16,530 psi 15,110 psi Collapse Pressure 16,510 psi 14,220 psi
Torsional Yield Strength 11,500 ft-lbs 8,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802030026103502000
9/2/09
2-7/8” 10.40 lbs/ft G-105 with NC 26 3-3/8” OD x 1-3/4” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade G-105 Connection NC 26
Interchangeable With 2-3/8” IF Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.79 lbs/ft
Capacity 0.185 US gal/ft Displacement 0.165 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-3/8” Inside Diameter 1-3/4”
API Drift 1-5/8” Rabbit OD, Suggested 1-9/16”
Minimum Make-up Torque 4,125 ft-lbs Maximum Recommend Make-up Torque 4,500 ft-lbs
Torsional Yield Strength 6,875 ft-lbs Tensile Strength (Torque Not Considered) 303,794 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.731 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.221 in2
Maximum Hook Load/Tensile Strength 300,000 lbs 233,100 lbs Slip Crushing / Slip Type (SDML) 258,700 lbs 202,600 lbs
Burst Pressure 23,140 psi 21,150 psi Collapse Pressure 23,110 psi 19,910 psi
Torsional Yield Strength 16,200 ft-lbs 12,400 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040026101502000
9/2/09
2-7/8” 10.40 lbs/ft S-135 with NC 26 3-5/8” OD x 1-3/4” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection NC 26
Interchangeable With 2-3/8” IF Upset Type IU
Nominal Weigh 10.40 lbs/ft Adjusted Weight 10.79 lbs/ft
Capacity 0.185 US gal/ft Displacement 0.165 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-5/8” Inside Diameter 1-3/4”
API Drift 1-5/8” Rabbit OD, Suggested 1-9/16”
Minimum Make-up Torque 4,300 ft-lbs Maximum Recommend Make-up Torque 4,700 ft-lbs
Torsional Yield Strength 7,100 ft-lbs Tensile Strength 313,700 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802010626103502000
9/2/09
2-7/8” 10.40 lbs/ft E-75 with Left Hand NC 26 3-3/8” OD x 1-3/4” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade E-75 Connection Left Hand NC 26
Interchangeable With Left Hand 2-3/8” IF Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.79 lbs/ft
Capacity 0.185 US gal/ft Displacement 0.165 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-3/8” Inside Diameter 1-3/4”
API Drift 1-5/8” Rabbit OD, Suggested 1-9/16”
Minimum Make-up Torque 4,100 ft-lbs Maximum Recommend Make-up Torque 4,500 ft-lbs
Torsional Yield Strength 6,900 ft-lbs Tensile Strength (Torque Not Considered) 313,700 ft-lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 214,300 lbs 166,500 lbs Slip Crushing / Slip Type (SDML) 184,800 lbs 144,700 lbs
Burst Pressure 16,530 psi 15,110 psi Collapse Pressure 16,510 psi 14,220 psi
Torsional Yield Strength 11,500 ft-lbs 8,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040126101102000
9/1/09
2-7/8” 10.40 lbs/ft S-135 with HT 26 3-5/8” OD x 1-1/2” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection HT 26
Interchangeable With N/A Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.05 lbs/ft
Capacity 0.183 US gal/ft Displacement 0.169 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-5/8” Inside Diameter 1-1/2”
API Drift 1-3/8” Rabbit OD, Suggested 1-5/16”
Minimum Make-up Torque 5,400 ft-lbs Maximum Recommend Make-up Torque 7,900 ft-lbs
Torsional Yield Strength 13,100 ft-lbs Tensile Strength (Torque Not Considered) 390,300 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040126102902207
9/1/09
2-7/8” 10.40 lbs/ft Internal Coated S-135 with HT 26 3-1/2” OD x 1-5/8” ID Arnco 300 XT Hard Band Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection HT 26
Interchangeable With N/A Upset Type EU
Internal Coating TK 34 Tool Joint Hard Band Arnco 300 XT
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.98 lbs/ft
Capacity 0.185 US gal/ft Displacement 0.169 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-1/2”
Inside Diameter 1-5/8” API Drift 1-1/2”
Rabbit OD, Suggested 1-7/16” Minimum Make-up Torque 4,800 ft-lbs
Maximum Recommend Make-up Torque 6,900 ft-lbs Torsional Yield Strength 11,400 ft-lbs
Tensile Strength (Torque Not Considered) 353,400 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in 2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040126102102000
9/1/09
2-7/8” 10.40 lbs/ft S-135 with HT 26 3-1/2” OD x 1-1/2” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection HT 26
Interchangeable With N/A Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.89 lbs/ft
Capacity 0.183 US gal/ft Displacement 0.169 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-1/2” Inside Diameter 1-1/2”
API Drift 1-3/8” Rabbit OD, Suggested 1-5/16”
Minimum Make-up Torque 6,600 ft-lbs Maximum Recommend Make-up Torque 7,300 ft-lbs
Torsional Yield Strength 12,100 ft-lbs Tensile Strength (Torque Not Considered) 390,300 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802049126101102000
9/1/09
2-7/8” 10.40 lbs/ft S-135 with Left Hand HT 26 3-5/8” OD x 1-1/2” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection Left Hand HT 26
Interchangeable With N/A Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.05 lbs/ft
Capacity 0.183 US gal/ft Displacement 0.169 US gal/ft
TOOL JOINT DATA
Outside Diameter 3-5/8” Inside Diameter 1-1/2”
API Drift 1-3/8” Rabbit OD, Suggested 1-5/16”
Minimum Make-up Torque 5,400 ft-lbs Maximum Recommend Make-up Torque 7,900 ft-lbs
Torsional Yield Strength 31,100 ft-lbs Tensile Strength 390,300 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802140326103502000
9/2/09
2-7/8” 10.40 lbs/ft VM 95 – SS with Hydril Wedge Thread 26 3-3/8” OD x 1-3/4” Tool Joint
DRILL PIPE SPECIFICATIONS
Grade VM 95 - SS Connection Hydril WT 26
Interchangeable With N/A Upset Type IU
Nominal Weight 10.40 lbs/ft Adjusted Weight 10.98 lbs/ft
Capacity 0.185 US gal/ft Displacement 0.166 US gal/ft
TOOL JOINT DATA
Minimum Yield Strength 120,000 psi Outside Diameter 3-3/8”
Inside Diameter 1-3/4” API Drift 1-5/8”
Rabbit OD, Suggested 1-9/16” Minimum Make-up Torque 2,800 ft-lbs
Maximum Recommend Make-up Torque 9,800 ft-lbs Torsional Yield Strength 12,300 ft-lbs
Tensile Strength (Torque Not Considered) 416,000 lbs
TUBE DATA New Premium
Outside Diameter 2.875 in 2.730 in Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 271,500 lbs 210,900 lbs Slip Crushing / Slip Type (SDML) 234,000 lbs 183,300 lbs
Burst Pressure 20,930 psi 19,140 psi Collapse Pressure 20,910 psi 18,010 psi
Torsional Yield Strength 14,600 ft-lbs 11,200 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802010031103902000
9/2/09
2-7/8” 10.40 lbs/ft E-75 with NC 31 4-1/8” OD x 2-1/8” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade E-75 Connection NC 31
Interchangeable With 2-7/8” IF Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.17 lbs/ft
Capacity 0.189 US gal/ft Displacement 0.171 US gal/ft
TOOL JOINT DATA
Outside Diameter 4-1/8” Inside Diameter 2-1/8”
API Drift 2” Rabbit OD, Suggested 1-7/8”
Minimum Make-up Torque 7,100 ft-lbs Maximum Recommend Make-up Torque 7,800 ft-lbs
Torsional Yield Strength 11,900 ft-lbs Tensile Strength (Torque Not Considered) 447,100 lbs
TUBE DATA
New Premium Outside Diameter 2-7/8” 2.730”
Inside Diameter 2.151” 2.151” Wall Thickness 0.362” 0.290”
Cross Sectional Area 2.858 sq in 2.220 sq in Maximum Hook Load/Tensile Strength 214,300 lbs 166,500 lbs
Slip Crushing / Slip Type (SDML) 184,800 lbs 144,700 lbs Burst Pressure 16,530 psi 15,110 psi
Collapse Pressure 16,510 psi 14,220 psi Torsional Yield Strength 11,500 ft-lbs 8,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802020031103702000
9/2/09
2-7/8” 10.40 lbs/ft X-95 with NC 31 4-1/8” OD x 2” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade X-95 Connection NC 31
Interchangeable With 2-7/8” IF Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.29 lbs/ft
Capacity 0.187 US gal/ft Displacement 0.173 US gal/ft
TOOL JOINT DATA
Outside Diameter 4-1/8” Inside Diameter 2”
API Drift 1-7/8” Rabbit OD, Suggested 1-13/16”
Minimum Make-up Torque 7,900 ft-lbs Maximum Recommend Make-up Torque 8,700 ft-lbs
Torsional Yield Strength 13,200 ft-lbs Tensile Strength 495,700 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 271,500 lbs 210,900 lbs Slip Crushing / Slip Type (SDML) 234,000 lbs 183,300 lbs
Burst Pressure 20,930 psi 19,140 psi Collapse Pressure 20,910 psi 18,020 psi
Torsional Yield Strength 14,600 ft-lbs 11,200 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802030031103702000
9/2/09
2-7/8” 10.40 lbs/ft G-105 with NC 31 4-1/8” OD x 2” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade G-105 Connection NC 31
Interchangeable With 2-7/8” IF Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.29 lbs/ft
Capacity 0.187 US gal/ft Displacement 0.173 US gal/ft
TOOL JOINT DATA
Outside Diameter 4-1/8” Inside Diameter 2”
API Drift 1-7/8” Rabbit OD, Suggested 1-13/16”
Minimum Make-up Torque 7,900 ft-lbs Maximum Recommend Make-up Torque 8,700 ft-lbs
Torsional Yield Strength 13,200 ft-lbs Tensile Strength 495,700 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 300,100 lbs 233,100 lbs Slip Crushing / Slip Type (SDML) 258,700 lbs 202,600 lbs
Burst Pressure 23,140 psi 21,150 psi Collapse Pressure 23,110 psi 19,910 psi
Torsional Yield Strength 16,200 ft-lbs 12,400 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed
27802040031103702000
9/2/09
2-7/8” 10.40 lbs/ft S-135 with NC 31 4-1/8” OD x 2” ID Tool Joint
DRILL PIPE SPECIFICATIONS
Grade S-135 Connection NC 31
Interchangeable With 2-7/8” IF Upset Type EU
Nominal Weight 10.40 lbs/ft Adjusted Weight 11.29 lbs/ft
Capacity 0.187 US gal/ft Displacement 0.173 US gal/ft
TOOL JOINT DATA
Outside Diameter 4-1/8” Inside Diameter 2”
API Drift 1-7/8” Rabbit OD, Suggested 1-13/16”
Minimum Make-up Torque 7,900 ft-lbs Maximum Recommend Make-up Torque 8,700 ft-lbs
Torsional Yield Strength 13,200 ft-lbs Tensile Strength 495,700 lbs
TUBE DATA
New Premium Outside Diameter 2.875 in 2.730 in
Inside Diameter 2.151 in 2.151 in Wall Thickness 0.362 in 0.290 in
Cross Sectional Area 2.858 in2 2.220 in2
Maximum Hook Load/Tensile Strength 385,800 lbs 299,800 lbs Slip Crushing / Slip Type (SDML) 332,600 lbs 260,400 lbs
Burst Pressure 29,750 psi 27,200 psi Collapse Pressure 29,720 psi 25,600 psi
Torsional Yield Strength 20,800 ft-lbs 15,900 ft-lbs
Excessive heat or pulling when tube is torqued can cause the maximum pull to decrease.
Where possible all figures are obtained from OEM data source.
NOTE: Weatherford in no way assumes responsibility or liability for any loss, damage or injury resulting from the use of the information listed above. All applications are for guidelines and the data described are at the user’s own risk and are the user’s responsibility.
Uncontrolled Document If Printed