2 ½ poly gunite jet (210-3700) installation · pdf file2 ½" poly gunite jet...
TRANSCRIPT
2200 East Sturgis Road, Oxnard, CA 93030 • Ph. (805) 981-0262 • Fax (805) 981-9403www.waterwayplastics.com • [email protected] 810-0023.0109© 2009 Waterway Plastics
2 ½" POLY GUNITE JET (210-3700) INSTALLATION INSTRUCTIONS AND PRESSURE TESTING
1. Hang Gunite Poly Jet Body with ties through preset holes onto steel rebar.
3. Glue 2 ½" cap onto end of pipe for pressure test being guniting.
5. Make a mark on the 1" PVC pipe flush or even with the end of the 2 ½" pipe.
7. Wrap Teflon tape on retainer ring if necessary and thread the 1" PVC pipe back into body with Poly Jet Wrench, making sure of a snug fit.
6. Unscrew 1" PVC pipe from body and cut 3 3⁄8" inward from the mark towards retainer ring, then glue wallfitting to 1" PVC pipe.
2. Estimate needed length of 2 ½" PVC pipe by thickness of wall. Cut 2 ½" PVC pipe at least 4" longer than estimated. Then glue 2 ½" PVC pipe to body.
Ties
Steel Rebar
Body (211-3060)
2" Water
Estimated Length
4"
8" min. from back of jet body
2 ½" Cap
4. After pool guniting, scoop around the pipe. Before plastering, cut the 2 ½" PVC pipe inside the wall and glue on the Gunite Poly Jet Plaster Niche (425-5030) (not included). Cover niche and tape then plaster over niche.
Gunite Wall
Chip out wallaround pipe
2 ½" PVC PipeSCH 40
Gunite Poly Jet Niche(425-5030)
Wall
Mark 1" PVC pipe�ush with wall
Retainer 0-Ring(805-0215)
Retainer Ring(219-1060)
3 3⁄8"
Make cut here
Mark linefrom step 5
Wall�tting (215-1070)
Wall
Retainer Ring (219-1060)
Poly Jet Wrench (218-1770)
Wrap Te�onTape
Wall�ttingAssembly
1 5
6
7
2
3
4
810-0023.0109© 2009 Waterway Plastics
8. If installing any of the internals above, use a Poly Jet Wrench to screw internal into wallfitting. Also available are metal escutcheons to cover plastic wallfittings (see below).
9. If installing a Deluxe Style internal, simply place into wallfitting and turn clockwise, hand tightening. When tight, turn counterclockwise to adjust to water flow.
Always use at least one Non-Adjustable internalper spa to prevent deadheading pump.
AdjustablePulsator
210-6060 - White10 GPM
AdjustablePulsator
210-6070 - White10 GPM
AdjustableRoto
210-6090 - White10 GPM
Adjustable210-6080 - White
10 GPM
AdjustableMassage (7 Nozzle)210-6700 - White
10 GPM
Stainless SteelTrim Escutcheon
916-6000
Wrench218-1770
AdjustableRoto
210-6120 - White10 GPM
Adjustable210-6100 - White
10 GPM
AdjustableMassage (7 Nozzle)210-6710 - White
10 GPM
Whirlpool210-979038 GPM
Monster210-8750
Four DifferentOrifices Included
5⁄16" 10 GPM3⁄8" 13 GPM7⁄16" 17 GPM½" 22 GPM
To prevent personal injury, shock, or property/equipment damage, an Air Spring Check Valve (2" 600-8160, 1 ½" 600-8140) must be installed on the blower stand pipe in case of a water backup in the air line.
Note: If a blower is not being used, please direct the air intake toward the groundusing the 2" Sweep Vent Grate Assembly (400-4130) on the Air Inlet Pipe.
Adjustable(210-6080)
Wall
Pulsator(210-6070)
Adjustable Roto(210-6090)
Whirlpool(210-9790)
Monster(210-8750)
Wrench(218-1770)
Wall
Deluxe StylePoly Jet Internal
Controller
8.00" min. length
5.989"4.290"
4.640"
1" SCH 40PVC Pipe
(not supplied)
Niche(not supplied)
(425-5030) 2 ½" SCH 40PVC Pipe
(not supplied)
1 ½" Socket Air 2" Socket Water
Blower
Water Flow Water Flow
AirFlow UL Listed
Check Valve
Air Intake
Sweep Vent Grate Assembly(400-4130)
AirFlow
Air Inlet Pipe
POLY JET INTERNALS AND ACCESSORIES
STAN
DARD
INTE
RNAL
S
NON-
ADJU
STAB
LE
DELU
XE SE
RIES
ACCE
SSOR
IES
Handheld Jet210-320010 GPM
8 9