2-way wireless security suite gs2065/tl265gs product technical training (international version)
TRANSCRIPT
2-Way Wireless Security Suite
GS2065/TL265GS Product Technical Training(International version)
2-Way Wireless Security Suite
GS2065/TL265GS– Product Overview
2-Way Wireless Security Suite
GS2065
GS2065 GSM/GPRS Wireless Alarm Communicator
Overview:The GS2065 provides primary or backup GSM/GPRS communication for the Alexor 2-way wireless security suite
Specifications:• Dimensions : 3.937"x5.875"x0.625" (100mmx150mmx15mm)• Weight : 68 g• Antenna Gain : 2db• Input Voltage : 11.1 to 12.6 V (from the PC-Link header)• Current Draw : 65 mA at 12V (400 mA during the GSM transmission)• Operating Environment : 5 º C to 40º C
(40º F to 104º F)
2-Way Wireless Security Suite
GS2065
GS2065 GSM/GPRS Wireless Alarm Communicator
Features:• Back up and primary GSM/GPRS alarm communication• Panel remote uploading/downloading support via GSM/GPRS • Advanced remote and local programming via DLS IV• Keypad programming through WT5500 wireless keypad• Individual Periodic Test Transmission via GSM/GPRS• Supervision heartbeats via GSM/GPRS• 128-bit AES encryption over GSM/GPRS• Full event reporting• Installer code• SIA format• PC-Link connection• Signal strength and trouble display• Optional Network Lock and SIM Lock• PC9155 replacement front plate (8 LEDs) included • Quad-Band: 850 MHz, 1900 MHz, 900 MHz and 1800 MHz
2-Way Wireless Security Suite
GS2065
GS2065 GSM/GPRS Wireless Alarm Communicator
Compatible Receivers:Sur-Gard System I Receiver: version 1.10 and higherSur-Gard System II Receiver: version 2.00 and higherSur-Gard SG-DRL3-IP: version 2.20 and higher (for Sur-Gard System III Receiver)
Compatible Control Panel:PC9155 Alexor Wireless Panel version 1.0 and higher
Product Model and Accessories:GS2065GS: For international marketGS-15ANTQ: Antenna Extension Kits with 15 feet cable GS-25ANTQ: Antenna Extension Kits with 25 feet cableGS-50ANTQ: Antenna Extension Kits with 50 feet cablePCLINK-5WP: PCLINK Kits for the programming with DLS IV
2-Way Wireless Security Suite
TL265GS
TL265GS Internet and GSM/GPRS Dual-Path Alarm Communicator
Overview:The TL265GS is an Internet and GSM/GPRS Dual-Path alarm communicator for the Alexor 2-way wireless security suite
Specifications:• Dimensions : 3.937"x5.875"x0.625" (100mmx150mmx18mm)• Weight : 78 g• Antenna Gain : 2db• Input Voltage : 11.1 to 12.6 V (from the PC-Link header)• Current Draw : 100 mA at 12V (400 mA during the GSM transmission)• Operating Environment : 5 º C to 40º C
(40º F to 104º F)
2-Way Wireless Security Suite
TL265GS
TL265GS Internet and GSM/GPRS Dual-Path Alarm Communicator
Features:• Fully redundant Internet and GSM/GPRS dual-path alarm
communication• Integrated call routing• Panel remote uploading/downloading support via GSM/GPRS and
Internet• Advanced remote and local programming via DLS IV• Keypad programming through WT5500 wireless keypad• Individual Periodic Test Transmission via GSM/GPRS and Internet• Supervision heartbeats via GSM/GPRS and Internet• 128-bit AES encryption via GSM/GPRS and Internet• Full event reporting• Installer code• SIA format• PC-Link connection• Signal strength and trouble display• Optional Network Lock and SIM Lock• PC9155 replacement front plate (8 LEDs) included • Quad-Band: 850 MHz, 1900 MHz, 900 MHz and 1800 MHz
2-Way Wireless Security Suite
TL265GS
TL265GS Internet and GSM/GPRS Dual-Path Alarm Communicator
Compatible Receivers:Sur-Gard System I Receiver: version 1.10 and higherSur-Gard System II Receiver: version 2.00 and higherSur-Gard SG-DRL3-IP: version 2.20 and higher (for Sur-Gard System III Receiver)
Compatible Control Panel:PC9155 Alexor Wireless Panel version 1.0 and higher
Product Model and Accessories:TL265GS: For International market GS-15ANTQ: Antenna Extension Kits with 15 feet cable GS-25ANTQ: Antenna Extension Kits with 25 feet cableGS-50ANTQ: Antenna Extension Kits with 50 feet cablePCLINK-5WP: PCLINK Kits for the programming with DLS IV
2-Way Wireless Security Suite
Global Approvals
GS2065 GSM/GPRS Wireless Alarm CommunicatorTL265GS Internet and GSM/GPRS Dual-Path Alarm Communicator
Now • FCC/IC, UL, ULC (North America)• CE, WEEE (Europe)• A-Tick (Australia/New Zealand)
September 2009• ANATEL (Brazil)• CNC (Argentina)• ICASA (South Africa)
November 2009•IMQ (Italy)
2-Way Wireless Security Suite
GS2065/TL265GS– Installation and programming
2-Way Wireless Security Suite
Installation
GS2065/TL265GS Installation
BEFORE YOU BEGIN
Have the following ready before installation:
• DSC DLS IV Programming Software • Control panel backup battery• Battery connection harness• Batteries for WT5500 2-way wireless keypad• Screwdriver• PCLINK-5WP Kits
PCLINK Header (Female) RJ11 cable Serial Header (DB9) Transformer (w/ connector to PCLINK header) 4 power plugs (international plugs)
2-Way Wireless Security Suite
Installation
GS2065/TL265GS Installation
Summary of Installation Steps
Step 1 – Connect the PCLINK-5WP cable between the computer and GS2065/TL265GS
Step 2 – Program the GS2065/TL265GS using DLS IV
Step 3 – Insert the SIM card in the GS2065/TL265GS
Step 4 – Connect the GS2065/TL265GS to the PC9155
Step 5 – Test for best signal strength location
Step 6 – Program Communication Sections on the PC9155 via keypad
Step 7 – Test communication
NOTE: All the options of the communicator also could be programmed through WT5500 2-way wireless keypad. Please see details in product manual.
2-Way Wireless Security Suite
GS2065/TL265GS – Installation
Step 1 – Connect the GS2065/TL265GS to the DLS computer using the PCLINK- 5WP
· If connected to the PC9155, power down the PC9155 and remove the PC-LINK connection
· Insert the PCLINK-5WP header to GS2065/TL265GS
· Connect the DB9 serial connector to the DLS computer
· Apply power to the PCLINK-5WP
Installation
2-Way Wireless Security Suite
GS2065/TL265GS – Installation
Installation
Step 2 – Program the GS2065/TL265GS usin g DLS IV
Step 2
Step 2.1 – Open DLS IV
2-Way Wireless Security Suite
GS2065/TL265GS – Installation
Installation
Step 2.2 – Create an account• Select ‘New Account’• Enter the account details
• Account Name• Panel Type (Communicator Module)• Connection Type (TL Network)
Account Name
Panel Type
Connection Type
2-Way Wireless Security Suite
GS2065/TL265GS – Installation
Installation
Step 2.3 – Module IP Address• Enter the IP address for the module
Communicator IP Address
2-Way Wireless Security Suite
GS2065/TL265GS – Installation
Installation
Step 2.4 – Enter SMS Details• Change ‘Connection Type’ to ‘SMS’• Enter a ‘User Name’• Enter a ‘Password’
• Select ‘Create’
Connection Type User Name
Password
Create
2-Way Wireless Security Suite
GS2065/TL265GS – Installation
Installation
Step 2.5 – Program the GS/IP options• The account will open• Select the ‘GS/IP’ tab• Enter the required information in the ‘GS/IP Options’ screen
2-Way Wireless Security Suite
GS2065/TL265GS – Installation
Installation
Step 2.6 – Program the Receivers options· Enter the required information in the ‘Receivers’ screen
2-Way Wireless Security Suite
GS2065/TL265GS – Installation
Installation
Step 2.7 – Program the GPRS options· Enter the required information in the ‘GPRS’ screen
2-Way Wireless Security Suite
GS2065/TL265GS – Installation
Installation
Step 2.8 – Load the programming to the communicator· Use “Global Download” and choose “PC-LINK” as the connection type. Then click “OK”
2-Way Wireless Security Suite
GS2065/TL265GS – Installation
Installation
Step 3 – Insert the SIM card
Ensure that the GS2065/TL265GS is powered down before inserting the SIM card
2-Way Wireless Security Suite
Installation
GS2065/TL265GS Installation
Step 4 – Install and wire the communicator to the control panel (on-site)GS2065/TL265GS: See details in product manual for PC9155 control panelFor PC9155D or PC9155G Kit, GS2065/TL265GS is pre-installed with the control panel
Red Wire
2-Way Wireless Security Suite
Installation
GS2065/TL265GS Installation
Step 5 - Test for best signal strength location
Ensure the SIM card is inserted Power up the control panel
Check Green LEDs. You must achieve full or medium signal strength. See details in product manual.
If signal strength is poor, must relocate the control panel or use an external extension antenna kits
2-Way Wireless Security Suite
Installation
GS2065/TL265GS Installation
Step 6 – Program communication options on the control panel via keypad
GS2065/TL265GS with PC9155 control panel o Sections [301], [302], [303], [305] : Program Communication
Path• DCAA - Internal (Ethernet 1,
Ethernet 2, GPRS 1, GPRS 2)
• DCBB - Ethernet Receiver 1• DCCC - Ethernet Receiver 2
(backup)• DCDD - GPRS Receiver 1• DCEE - GPRS Receiver 2
(backup)
o Section [350] : Program Communication Format (Communicator)• (If Option [301] (above) is set to DCAA,
Option [350] must be set to SIA, sub-option 5)
o Sections [351] to [376] : Program Call Directiono Section [382] : Enable T-LINK Interface (Option [5])o Section [383] : Program Back-up or Independent Communicationo Section [167] : Enable Communication Wait For ACK (Set to 60
seconds)o Section [401] : Enable DLS Session Through GPRS or Ethernet
(Option [1])
2-Way Wireless Security Suite
Installation
GS2065/TL265GS Installation
Step 7 – Test communication
1. Disconnect incoming phone line from TIP and RING on the control panel 2. Verify that LED 2 is on, this indicate that the unit is active3. Create an alarm transmission 4. Verify alarm transmission by calling monitoring station5. Re-connect the phone line, if necessary
For back-up communication applications, perform steps 1 to 5For primary communication applications, perform steps 3 and 4 only
2-Way Wireless Security Suite
Programming
GS2065/TL265GS Remote Programming
We need several slides here to show how remotely get the DSL connection to re-program the communicator •Via Ethernet/Internet connection•Vis SMS initiated connection
2-Way Wireless Security Suite
Installation
LED Display
Trouble Status LED (Yellow)
Please see details about the trouble shooting on page 17 in product manual
2-Way Wireless Security Suite
Installation
LED Display
Network Connection Status LED (Red)
LED OFF•No network connection issue present
LED ON•Physical Ethernet cable is not connected•DHCP configuration fails•Fails to get an IP address from the GPRS network•GPRS connections has been reset
LED blinks quickly once•Ethernet transmitting
LDE blinks quickly twice•Ethernet receiving
2-Way Wireless Security Suite
Installation
LED Display
Signal Strength LED 2 (Green)
Signal Strength LED 1 (Green)
Green LED 2 blinks quickly once•GPRS transmitting
Green LED 2 blinks quickly twice•GPRS receiving
2-Way Wireless Security Suite
Installation
Keypad Trouble Display
Trouble Condition•Alternate Communicator Trouble
Description•SIM Card Lock•GSM Trouble•Ethernet Trouble•Central Station Receiver Trouble•Supervision Trouble•SMS Config Trouble
2-Way Wireless Security Suite
GS2065/TL265GS– Applications
2-Way Wireless Security Suite
Applications
GS2065/TL265GS Call Routing (Internal)
Communicator Controlled Call Routing – Backup (dual-path)
– Redundant (dual-path)
Required ProgrammingPanel Sections [301], [302],[303] and [305]
• Any of them could be programmed as DCAADCAA (default): Ethernet 1 → Ethernet 2 → GRPS 1 → GPRS 2
Communicator Sections [005]Option [004] - Primary and backup path
[ON]: GPRS path primary, Ethernet path backup
[OFF]: Ethernet path primary, GPRS path backup
Option [005] - Redundant between GPRS path and Ethernet path [OFF]: Disable
redundancy[ON]: Enable redundancy
2-Way Wireless Security Suite
Applications
GS2065/TL265GS Call Routing (Internal)
Backup Mode 1: Ethernet Primary, 4 Receivers
Ethernet Receiver 1
Ethernet Receiver 2
GPRS Receiver 1
GPRS Receiver 2
IP Receiver* 1
IP Receiver 2
IP Receiver 3
IP Receiver 4
Tx 2 failed, TX3
TX 1
Tx 3 failed, Tx4
Tx 1 failed, Tx2
2-Way Wireless Security Suite
Applications
GS2065/TL265GS Call Routing (Internal)
Backup Mode 2: Ethernet Primary, 2 Receivers
Ethernet Receiver 1
Ethernet Receiver 2
GPRS Receiver 1
GPRS Receiver 2
IP Receiver 1
IP Receiver 2
TX 1
Tx 3 failed, Tx4
Tx 1 failed, Tx2
Tx 2 failed, TX3
2-Way Wireless Security Suite
Applications
GS2065/TL265GS Call Routing (Internal)
Backup Mode 3: GPRS Primary, 4 Receivers
Ethernet Receiver 1
Ethernet Receiver 2
GPRS Receiver 1
GPRS Receiver 2
IP Receiver 1
IP Receiver 2
IP Receiver 3
IP Receiver 4
Tx 2 failed, TX3
TX 1
Tx 3 failed, Tx4
Tx 1 failed, Tx2
2-Way Wireless Security Suite
Applications
GS2065/TL265GS Call Routing (Internal)
Backup Mode 4: GPRS Primary, 2 Receivers
Ethernet Receiver 1
Ethernet Receiver 2
GPRS Receiver 1
GPRS Receiver 2
IP Receiver 1
IP Receiver 2
TX 1
Tx 3 failed, Tx4
Tx 1 failed, Tx2
Tx 2 failed, TX3
2-Way Wireless Security Suite
Applications
GS2065/TL265GS Call Routing (Internal)
Redundant Mode: 4 Receivers – (Redundancy between GSM/GPRS path and Ethernet/Internet path)
Ethernet Receiver 1
Ethernet Receiver 2
GPRS Receiver 1
GPRS Receiver 2
IP Receiver 1
IP Receiver 2
IP Receiver 3
IP Receiver 4
TX1, GPRS path
TX 1, Ethernet path
TX 1 failed, TX 2 via GPRS path
TX1 failed, TX 2 via Ethernet path
NOTE: The application requires 4 different SG receivers or SG-DLR3 IP line cards
2-Way Wireless Security Suite
Applications
GS2065/TL265GS Call Routing (External)
PC9155 Panel Controlled Call Routing Backup (triple-path)
• Panel section [383] – Options [2],[3] and [4] enabled
• Panel section [380], Option [6] disabled Redundant (triple-path)
• Panel sections [351] – [376] Options enabled Alternate (triple-path)
• Panel section [380] – Option [6] enabled
Required ProgrammingPanel Sections [301], [302],[303] and
[305] • Phone #: Phone number of the receiver • DCBB: Ethernet Receiver 1• DCCC: Ethernet Receiver 2• DCDD: GPRS Receiver 1
• DCEE: GPRS Receiver 2
2-Way Wireless Security Suite
Applications
GS2065/TL265GS Call Routing (External)
PC9155 Panel Controlled Call Routing–Backup: Panel Section [383] – Options [2],[3] and [4] enabled
DC DD[305]
DC C C[303]
DC B B[302]
1-800-xxxxxxx[301]
DC DD[305]
DC C C[303]
DC B B[302]
1-800-xxxxxxx[301]
Phone Line Receiver 1
IP Receiver 1
IP Receiver 2
IP Receiver 3
Phone Line path
Ethernet Receiver 1
Ethernet Receiver 2
GPRS Receiver 1
TX 1
Tx 1 5 failures, Tx2
Tx 2 5 failures, Tx3
Tx 3 5 failures, Tx4
Example
2-Way Wireless Security Suite
Applications
GS2065/TL265GS Call Routing (External)
PC9155 Panel Controlled Call Routing– Redundant: Panel Sections [351] – [376] Options enabled
DC DD[305]
DC C C[303]
DC B B[302]
1-800-xxxxxxx[301]
DC DD[305]
DC C C[303]
DC B B[302]
1-800-xxxxxxx[301]
Phone Line Receiver 1
IP Receiver 2
IP Receiver 3
IP Receiver 4
Phone Line path
Ethernet Receiver 1
Ethernet Receiver 2
GPRS Receiver 1
TX 1
TX 1
TX 1
TX 1
Example
2-Way Wireless Security Suite
Applications
GS2065/TL265GS Call Routing (External)
PC9155 Panel Controlled Call Routing–Alternate: Panel section [380] – Option [6] enabled
DC DD[305]
DC C C[303]
DC B B[302]
1-800-xxxxxxx[301]
DC DD[305]
DC C C[303]
DC B B[302]
1-800-xxxxxxx[301]
Phone Line Receiver 1
IP Receiver 1
IP Receiver 2
IP Receiver 3
Phone Line path
Ethernet Receiver 1
Ethernet Receiver 2
GPRS Receiver 1
TX 1
Tx 1 1 failure, Tx2
Tx 2 1 failure, Tx3
Tx 3 1 failure, Tx4
5 rounds total
Example
2-Way Wireless Security Suite
Applications
Other Applications
Keypad Programming •All options of the communicator could be programmed from WT5500 keypad •Control Panel option [851], Communicator option [999]-55NOTE: A module reset is required if any options have been changed by the keypad.
Periodic Test transmission•Individual periodic test transmission via GPRS and Ethernet•Customized Time of Day for test transmission•Daily, Weekly and Monthly Interval•Communicator Options [026], [028], [029], [124], [125], [224] and [225]NOTE: Enabling this feature will require more data usage.
Encryption•128 Bit AES Encryption •Turned on by central monitoring station Sur-Gard receiver•Encrypted communications enabled after next event sent to the receiverNOTE: Enabling this feature will require more data usage.
2-Way Wireless Security Suite
Applications
Other Applications
Supervision Type•Commercial Type and Residential Type•Commercial Type can Swap Detection and require more data usage than Residential Type•Communicator option [005]-[3]
Heartbeats Interval•Should be 65 seconds less than the supervision window programmed at the receiver. •Send heartbeats to Ethernet 1 and/or GRPS 1 receiver•Communicator option [004] and [005]-[1]&[2]
NOTE: Enabling this feature will require more data usage.
2-Way Wireless Security Suite
Applications
Other Applications
Installer Code•Required to program the communicator by using DLS IV remotely/locally•Communicator option [11]
Optional Carrier and SIM Lock •Lock the unit to a specific carrier’s network•Lock the unit to a SIM card with a specific PIN numberNOTE: This feature is available upon request of specific carrier networks.
Public APN•Use Public APN for DLS session if the communicator is operating on a private APN•GPRS Login User Name and Password might be required •Communicator option [221] to [223]
2-Way Wireless Security Suite
Applications
Other Applications
Power Save Mode•Extend the battery duration when an AC power loss on control panel•Ethernet functionality turned off until a new event need to be transmitted•Network Connections LED: OFF•Incoming DLS connection will not be possible
Hardware Default •Reset the programming options to the factory setting (default values)NOTE: Please see details in product manual
Software Update •Update the firmware through DLS IV locally via PCLINK•Update the firmware through DLS IV remotely via Ethernet/Internet (TL265GS only)•Communicator option [005]-[6]
2-Way Wireless Security Suite
Applications
Other Applications
System Information •Upload and read the system status by using DLS IV•Also readable from WT5500 keypad
Firmware versionEthernet IP addressEthernet gateway IP addressGRPS IP addressSIM numberGSM phone numberIMEI numberMAC addressModule Default/Reset
2-Way Wireless Security Suite
Applications
SIA Report Code
Event SIA Data Code SIA Address Field Panel Absent Trouble ET 001Panel Absent Trouble Restore ER 001Radio Activation Restore RS 001Ethernet 1 Test Transmission RP 001GPRS 1 Test Transmission RP 003GPRS 2 Test Transmission RP 004FTC Restore YK 001
Example: Nri0 ET001 N= New Eventri0=Partition/Area identifierET= Panel Absent Restore 001=Zone 001
NOTE: GPRS 2 Test Transmission will only be sent when two different APNs are programmed.