2010 c&ms - ohio department of transportation · web viewseeding and mulching - hydrated lime...

700 MATERIAL DETAILS

700 MINIMUM REQUIREMENTS FOR SAMPLING MATERIALS

Spec No. Material Material only Inspection or Sampling Requirements

Post Inspection Instructions

203 Embankment Assure 203.02 Q and R materials conform to the individual material requirements. Sample materials when requested by the Engineer.

Follow S 1015 for acceptance

Soil Embankment: 50 lb (23 kg)Granular Embankment: 50 lb (23 kg)

258 Dowel Bar Retrofit Silicone SealantDowel Bar grout

301302

Asphalt Concrete Base

Project: Visually inspect delivered loads and newly placed mat

Plant: Test 1 sample in 4 days for verification. Observe other contractor QC sample and QC test 1 in 4 days.Plant: Conduct minimum monitoring requirements.

Project: Contact project Engineer/ DCE/DET immediately if problems are seen

Plant: Compare results per 403. Report on monitoring.

305 PC Concrete Pavement

Make two 6"x6"x4' beams for every 7500 yd² (6500 m²) or fraction thereof daily. Field test beams for required load for the specification.Report results in CMS.

Core samples taken every 2000 sq. yds by Contractor. Conform to S 1064

306 Cement Treated Free Draining Base

Report mix design and verification to Lab. Conform to S 1090 when determining compaction

Determine locations for thickness tolerance checks according to S 1064.

307 Non Stabilized Drainage Base

Provide samples conforming to 703.12 for design verification. Provide in process samples as directed by the Engineer. Sample material conforming to 703.12


308 Asphalt Treated Free Draining Base

Provide a JMF to the Lab for approval. Include 1 gal (4 L) sample of asphalt and 70 lb (32 kg) sample of aggregate


409 Sawing and Sealing Asphalt Concrete pavement Joints

Assure backer rod is on QPL at the time of use.Inspect material for condition.Document in CMS.

Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District testing and OMM

421 Micro Surfacing Project: Conduct a test strip per 421.09, inspect per 421.10 and accept per 421.11.

422 Chip Seal with Polymer Binder

Project: Conduct a test strip per 422.05. Clean the surface per 422.06. Verify binder and aggregate application per 422.07 and 422.08. Ensure contractor quality control per 422.10. Verify all of 422.11 is met for acceptance.

423 Fibers for Asphalt Concrete:PolyesterPropylenePolyproplylene

Verify type and brand name of material is on QPL at the time of use. Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use submit a use a 1 quart sample to the Laboratory.

424 Asphalt Concrete (Fine Graded Polymer)

For Type A see 301,302 procedures. For Type B see 448 procedures.



442 Asphalt Concrete Project and Plant: See requirements for 446 or 448 as specified for the 442 item.Plant: 1 per week have contractor take 2 1-quart samples, label and hold.

443 Asphalt Concrete (Stone Mastic)

See 446 requirements.

446 Asphalt Concrete Project: Visually inspect delivered loads and newly placed matProject: Obtain daily mix sample for District test unless otherwise directed by the DET.Project: Obtain 10 cores for each lot (day) within 48 hours for District test. Locate cores for sampling. Project: See 702.04 or 702.13 for tack sample.Plant: Conduct minimum monitoring requirements.Plant: See 702.01 for PG binder sample

Project: Contact project Engineer/ monitoring team immediately if problems seen.Project: Observe proper handling and quick delivery of the mix sample. Place cores in box flat side down, do not stack boxes, do not leave in weather, deliver to lab promptly.Plant: Report on monitoring.

448 Asphalt Concrete Project: Visually inspect delivered loads and newly placed matProject: Give lot sample location to the District monitoring team unless otherwise directed by the DET.Project: See 702.04 or 702.13 for tack sample.Plant: Conduct minimum monitoring requirements.Plant: See 702.01 for PG binder sample

Project: Contact project Engineer/monitoring team immediately if problems seen.Plant: Report on monitoring.




451.08.B Dowel Bond Breaking Material

Check new light form oil by labels on new cans. No sampling required

Report material as not approved and follow policy for non specification materials




499.02 Water Potable water is satisfactory.If question about water quality, obtain 1 gallon sample.Document in CMS.

Notify District Testing if water appears to contain sewage, oil, acid, or other matter.

503.09 Excavation for StructuresBackfill

Sampled only when requested by the Engineer per Section 203Soil Embankment: 50 lb (23 kg)Granular Embankment: 50 lb (23 kg)

504 Sheet Piling Left in Place

Use 711.03 materials

507.03 Bearing Piles Steel Pile Points

Only use points from suppliers on the approved list incorporated into the project plans.Document in CMS as needed.

Notify District Testing if material non-performs or looks defective during use. Notify the contractor with non-compliance issues.

509.08 Reinforcing Steel - Plastic support chairs

Assure plastic supports conform to supplement 1125



511 Concrete for Structures

Make two 6"x12" cylinders for spans over 20 ft each day, each 200 yd³.For spans 20 ft span and under, make two 6"x12" cylinders each 50 yd³ or less.Document in CMS.Field or Standard Cure according to ACI/ODOT specifications.

Within 24 to 48 hours after sampling, ship cylinders to Laboratory with required documentation.

515.15 Prestressed Concrete Bridge Members -Corrosion Inhibitors

Verify manufacturer is on Approved List maintained by OMM. Document in CMS.

526 Approach Slabs Make two 6"x12" cylinders for each day, each 200 yd³.Document in CMS.Field or Standard Cure according to ACI/ODOT specifications.

Within 24 to 48 hours after sampling, ship cylinders to Laboratory with required documentation.

601.11 Tied Concrete Block Mats(Slope/Channel Protection)

Verify company and brand name of material is on QPL at the time of use. Inspect material for condition.Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use submit a representative qty of defective material to the Laboratory.

603.02 External Sealing Bands Joint Wrap

Verify company and brand name of material is on QPL at the time of use. Inspect material for condition.Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use submit a representative qty of defective material to the OMM.

609.02 Curbing, Concrete Medians, and Traffic Islands - Stone Curbs

Contact District Testing and OMM Aggregate Section to assure stone curb conforms to requirements of 609.02

610 Cellular Retaining Walls

610.04.A Cellular Products will be supplied by a source on the Certified Lists for S-1073 maintained by OMM.Received with TE-24.Check dimension, condition and compliance with approved drawings.Document in CMS.610.04.B Cellular Products assure documentation is complete and approved by Lab.

Notify District Testing if rejecting material. If material non-performs or looks defective during use 1notify District Testing and OMM.

613 Low Strength Mortar Backfill

Supplier to perform trial batches of 1 cy to ensure flowable consistency.Refer to Item 613.05 for mix design proportions.Alternative mix will be submitted for approval 30 days prior to placement.


622 Concrete Barriers 622.04 Products will be supplied by a source on the Certified List for S-1073 maintained by OMM.Received with TE-24.Check dimension, markings, roughness or excessive cracks.Document in CMS.




632.11 Traffic Signal Equipment Loop Detector Sealant

Verify manufacturer is on Approved List maintained by OMM.Inspect for condition, appearance and package markings.Document in CMS.


633 Traffic Signal Controllers

Inspect material for condition and conformance to shop drawings.Manufacturer’s certified test data required for acceptance.Refer to Handbook of Procedures for Contractor Certification of Lighting, Signing & Traffic Signal Working Drawings on OMM Manual website.

Notify District Testing if rejecting material.

653.02 Topsoil Obtain one (1) pint sample of material from each source and/or stockpile of visually different material from same source.Use friction top, air tight metal container supplied by the Department.Submit to Office of Geotechnical Engineering Operations.Samples will include a TE-31 form or CMS print screen

657.02 RipRap for Tree Protection

Confirm with DET that the aggregate source has a acceptable performance history. For sources with poor performance require test data conforming to ASTM D5240

658.02 Tree Root Aeration - Aggregate

Assure source on the Certified List for S 1069 maintained by OMM Assure aggregate meets soundness requirements. Sample sources with no soundness history and obtain a 100 lb (45 kg) sample

659.03 Seeding and Mulching - Liming Materials

Only accept materials from suppliers licensed in Ohio. See OMM website for list of Ohio Department of Agriculture list of licensed suppliers. Document in CMS

659.03 Seeding and Mulching - Hydrated Lime Slurry

Verify company and brand name of material is on QPL at the time of use. Document in CMS.


659.04 Seeding and Mulching - Commercial Fertilizer

Only accept materials from suppliers licensed in Ohio. See OMM website for list of Ohio Department of Agriculture list of licensed suppliers. Inspect material for certified analysis and condition.Non-standard application rate require approval prior to useDocument in CMS.

Licensing is required. Notify District Testing if rejecting material.If material non-performs or looks defective during use notify District Testing & OMM.



659.07659.08659.09S1022

Seeding and MulchingSeedsLegumesNative Grasses and Wildflowers

Verify manufacturer is on certified supplier List maintained by OMM.Received with TE-24 and description bill of lading. Document in CMS.

Verify District approval of seed mixture.

659.14659.15659.16

Seeding and Mulching - Mulch

Material should be reasonably free from foreign matter that would inhibit seed germination.

Notify District if rejecting material.

660.02 Sodding Verify company and brand name of material is on QPL at the time of use. Certification required for each shipment.Document in CMS.


661 Planting Trees Shrubs and Vines[Trees][Shrubs][Vines]

Verify company and brand name of material is on QPL at the time of use. Inspect material for condition.Plant material should be sealed until use.Document in CMS.

Final acceptance should take place after period of establishment.Notify District Testing if rejecting material.

STANDARD MATERIALS SPECIFICATIONS

701.01701.02701.04701.05701.07701.09

Cement, HydraulicASTM Types I, IA, II, IIIMasonrySlag Modified Type I(SM)

Verify manufacturer on Concrete Plant Batch Ticket is on Certified List for S 1028 maintained by OMM. Verify material against bill of lading description.Document in CMS.

Obtain one ½ gallon sample and original bill-of-lading per concrete plant every 180 days for QA. Ship sample to OMM laboratory. Ensure that sample container is filled to capacity prior to transport.

701.10 Micro-Silica Admixture

Verify manufacturer on Concrete Plant Batch Ticket is on Certified List for S 1045 maintained by OMM. Verify material against bill of lading descriptionDocument in CMS.

Obtain one ½ gallon sample and original bill-of-lading per concrete plant every 180 days for QA. Ship sample to OMM laboratory.Ensure that sample container is filled to capacity prior to transport.

701.11 Ground Granulated Blast Furnace (GGBF) Slag

Verify manufacturer on Concrete Plant Batch Ticket is on Certified List for S 1034 maintained by OMM. Verify material against bill of lading descriptionDocument in CMS.


701.13 Fly Ash Verify manufacturer on Concrete Plant Batch Ticket is on Certified List for S 1026 maintained by OMM. Verify material against bill of lading descriptionDocument in CMS.If high LOI flyash verify manufacturer on Concrete Plant Batch Ticket is on List for S 1115.




702.01 Asphalt Binder Certified asphalt PG binder: As directed by the Lab. Plant: Minimum of one sample per project per season, except for inconsequential quantities.

Non-Certified PG binder: Will be sampled and approved by the Department before use.

Certified binder: Plant: Submit sample to Lab.

Non-certified binder: Submit to Lab. Do not allow asphalt production until material is approved.

702.02702.03702.04702.07702.13

Cut Back AsphaltCut Back Asphalt EmulsionsEmulsified AsphaltsAsphalt Emulsion MWSRubberized Asphalt Emulsion

Certified material: At the refinery or source as directed by the Lab. Project and/ or Plant: One sample per each 25,000 gallons. None for less than 300 gallons.

Non-certified material: Will be sampled and approved by the Department before use.

Certified material: Submit to Lab.

Non-certified material: Submit to Lab. Do not use until approved by Lab.

702.05702.06

Asphalt Primer WaterproofingAsphalt Waterproofing

Each batch sampled and pre-approved per TE 24. Lab contacted by supplier for test.

Project: Do not accept on project without TE 24.

702.14 Rubber Compound 1Certified test data702.16 Polymer

Emulsified Binder1Certified test data

702.17 Crack Sealant Material is pre-tested and approved.Will be shipped with TE-24.Document in CMS.

Notify District Testing if rejecting material. If material non-performs or looks defective during use 1Notify District Testing and OMM Asphalt Section.

703.02703.04703.05703.08

Coarse Aggregate - Group 0

Products will be supplied by a source on the Certified List for S 1069 maintained by OMM.Document in CMS.

60 to 75 lb. QC sample taken by District lab at source a minimum two (2) times per year. 100 lb QC sample for sizes 1,2, and 24.No project sampling required except if project believes there is a problem with the material [either gradation or quality]

703.02703.04703.05703.08



60 to 75 lb. QC sample taken by District lab at source a minimum four (4) times per year.No project sampling required except if project believes there is a problem with the material [either gradation or quality]

703.02703.04703.05703.08703.10


Products will be supplied by a source on the Certified List for S 1069 maintained by OMM.60 to 70 lb. QC sample taken from each 2600 ton (2360 metric ton) stockpile, submitted to OMM Aggregate Section. 100 lb QC sample for sizes 1,2, and 24.Document in CMS.Do not use until tested and approved.

1No additional project sampling required for approved, sampled tonnage except if project believes there is a problem with the material [either gradation or quality]



703.02703.03703.04703.05703.06

Fine Aggregate - Group 0


30 to 40 lb. QC sample taken by District lab at source a minimum two (2) times per year.No project sampling required except if project believes there is a problem with the material [either gradation or quality]

703.02703.03703.04703.05703.06




703.02703.03703.04703.05703.06


Products will be supplied by a source on the Certified List for S 1069 maintained by OMM.30 to 40 lb. QC sample taken from each 1800 ton (1640 metric ton) stockpile, submitted to OMM Aggregate Section.Document in CMS.Do not use until tested and approved.

No additional project sampling required for approved, sampled tonnage except if project believes there is a problem with the material [either gradation or quality]

703.02703.04703.05

Dense Graded Aggregate - Group 0



703.02703.04703.05




703.02703.04703.05




703.07 Materials Mineral filler

For limestone dust assure from a source on Certified List for S 1069.For Portland cement assure source is on Certified list for S 1028For inert mineral filler sample for gradation. Submit to District Lab.



703.11 Type 1

Structural Backfill for 603 Bedding and Backfill – Group 0 and 1 sources

Group 0 and 1 sources Assure materials provided by a source on the Certified List for S 1069Document in CMS


703.11 Type 1

Structural Backfill for 603 Bedding and Backfill – Group 2 sources

Group 2 sources Assure materials provided by a source on the Certified List for S 106990 to 100 lb. QC sample taken from each 5200 ton (4720 metric ton) stockpile, submitted to OMM Aggregate Section.Document in CMS.Do not use until tested and approved.


703.11 Type2

Structural Backfill for 603 Bedding and Backfill - – Group 0 and 1 sources



703.11 Type2

Structural Backfill for 603 Bedding and Backfill - Group 2 sources

Group 2 sources Assure materials provided by a source on the Certified List for S 106990 to 100 lb. QC sample taken from 5200 ton (4720 metric ton) stockpile, submitted to OMM Aggregate Section.Document in CMS.Do not use until tested and approved.


703.11 Type 3

Structural Backfill for 603 Bedding and Backfill – Group 0 and 1 sources



703.11 Type 3

Structural Backfill for 603 Bedding and Backfill – Group 2 sources



703.12.A Aggregate for 306 and 307 – Group 0 an 1 sources





703.12.A Aggregate for 306 and 307 – Group 2 sources



703.12.B Aggregate for 306 and 307 – Group 0 and 1 sources



703.12.B Aggregate for 306 and 307 – Group 2 sources



703.13 Coarse Aggregate for Items 451 and 452

Assure materials provided by a source on the Certified List for S 1069Assure materials are on the OMM Freeze Thaw List Follow requirements of coarse aggregate 703.02Document in CMS

No project sampling required except if project believes there is a problem with the material [either gradation or quality]

703.14 Open-Hearth Steel Slag Aggregate Used for Item 304

Assure materials from a source on the Certified List for S 1069Stockpile and sample each 2500 tons (2300 metric tons). Notify the District laboratory for inspection of sources and to obtain split samples. Test for expansion


703.15 Open-Hearth, Electric Arc Furnace, and Basic Oxygen furnace Steel Slag Aggregate Used for Items 410, 411, and 617

See requirements for 703.14 See requirements for 703.14

703.16 Suitable Materials for Embankment Construction

Multiple materials listed. Follow the requirements of the individual material specification

Follow the requirements of the individual material specification

Modification required for 703.16



703.17 Group 0 Materials Aggregate base









703.18 Group 0 Materials for Items 410, 411, and 617.









703.19.A Crushed Aggregate Slope Protection and Filter Aggregate for Dump Rock Fill

Products will be supplied by a source on the Certified List for S 1069 maintained by OMM.Document in CMS

No sampling required except if project believes there is a problem with the material [either gradation or quality]



703.19.B Dumped Rock Fill and Rock Channel Protection

Products will be supplied by a source on the Certified List for S 1069 maintained by OMM.Confirm with OMM laboratory source has know durability historySample on direction of the OMM laboratoryDocument in CMS

No sampling required except if project believes there is a problem with the material [either gradation or quality]

704.01704.02704.03

Block:BrickConcrete MasonryShale

Verify type of material is on QPL at the time of use. Inspect for condition and defects.Document in CMS.

Notify District Testing if rejecting material.When material non-performs or looks defective during use reject material and sample 12 brick representative of defect to OMM for QA follow-up.

705.01 Fiber Reinforced Polymer (FRP) Dowel Bars

Certified test data from an accredited testing facility will accompany each shipment.Document in CMS.

Notify District Testing upon receipt of shipment.

705.03 Joint FillerPreformed

Verify type and brand name of material is on QPL at the time of use.Inspect for condition, appearance and dimension.Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use send one (1) 1.5'x2.5' sample representative of defect to OMM for QA follow-up.

705.04 Joint and Crack SealerHot Applied

Material is pre-tested and approved.Will be shipped with TE-24.Document in CMS.

Notify District Testing if rejecting material. If material non-performs or looks defective during use 1nnotify District Testing and OMM Asphalt Section for sampling requirements.

705.05 Burlap Cloth Materials

Inspect for condition, appearance and dimension.Documenting in CMS .is not requiredOnly sample if there if questioning material meet specification

Notify District Testing if rejecting material.If material non-performs or looks defective during use 1notify District Testing and OMM.

705.06 Sheet Curing Materials

Inspect for condition, appearance and dimension.Documenting in CMS is not required.Only sample if there if questioning material meet specification


705.07 Concrete Curing Compounds

Verify type and brand name of material is on QPL at the time of use.Inspect for condition and appearance.Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use send one (1) quart sample representative of defect to OMM, Cement and Concrete section, for QA follow-up.



705.10 Air Entraining Admixtures

Verify type and brand name of material listed on Concrete Plant Batch Ticket is on QPL at the time of use.Document in CMS.

Storage: Admixtures should be stored at concrete producer in such a manner to permit easy access for proper identification in weather resistant units.Provide minimum QA sample of one (1) every 180 days per concrete plant, each material, each company. Minimum sample size one (1) quart

705.11 Joint SealerPreformed Elastomeric

Verify type and brand name of material is on QPL at the time of use.Inspect for condition, appearance, dimension and manufacturer trademark. Document in CMS.

Notify District Testing if rejecting material because material non-performs or looks defective during use.

705.12 Chemical Admixtures for Concrete

Verify type and brand name of material is on QPL at the time of use.Document in CMS.

Storage: Admixtures should be stored at concrete producer in such a manner to permit easy access for proper identification in weather resistant units.Provide minimum QA sample of one (1) every 180 days per concrete plant, each material, each company. Minimum sample size one (1) quart.

705.15 High Molecular Weight Methacrylate (HMWM)


705.20 Non Shrink, Non Metallic Grout


Notify District Testing if rejecting material.If material non-performs or looks defective during use 1notify District Testing and OMM for sampling requirements.

705.21 Quick Setting Concrete Mortar


Notify District Testing if rejecting material.If material non-performs or looks defective during use 1notify District Testing and OMM for sampling requirements.

705.22 Non-shrink Mortar Verify manufacturer is on the Approved List maintained by OMM.Inspect for condition, appearance and dimension.Make three (3) or more 3"x6" cylinders from keyway mix.Ship to OMM Concrete Section. Document in CMS.

Sample will be tested at 3, 7 and 28 days.Do not open structure to traffic until a compressive strength of 5000 psi (34.5 MPa) is achieved.

705.23 A Epoxy-urethane Sealers

Verify type and brand name of material is on QPL at the time of use.Inspect for condition, dimension, suitability for intended use.Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use obtain 1 qt (1 L) samples in a sealed container and send to OMM.



705.23 B Non Epoxy Sealers Verify type and brand name of material is on QPL at the time of use.Inspect for condition, dimension, suitability for intended use.Document in CMS.


705.24 Soluble Reactive Silicate



705.25 Gravity Fed Resin Verify type and brand name of material is on QPL at the time of use.Inspect for condition, dimension, suitability for intended use.Document in CMS.


705.26 Epoxy injection Resin



706.01 Non-Reinforced Concrete Pipe

Assure products are supplied by a source on the Certified List for S-1074 maintained by OMM.Received with TE-24.Check dimension, markings, roughness or excessive cracks.Document in CMS.

Iif rejecting material because material non-performs or looks defective during use, notify District Testing and OMM, Cement and Concrete section,

706.02 Reinforced Concrete Circular Pipe


If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM, Cement and Concrete section,

706.03 Reinforced Concrete Pipe, Epoxy Coated



706.04 Reinforced Concrete Elliptical Culvert, Storm Drain and Sewer Pipe



706.05 Precast Reinforced Concrete Box Sections





706.051 Precast Reinforced Concrete Three-Sided Flat Topped Culverts



706.052 Precast Reinforced Concrete Arch Sections



706.06 Perforated Concrete Pipe



706.07 Concrete Drain Tile



706.08 Vitrified Clay Pipe Verify type and brand name of material is on QPL at the time of use.Inspect for condition, appearance and dimension.Document in CMS.


706.09 Clay Drain Tile Verify type and brand name of material is on QPL at the time of use.Inspect for condition, appearance and dimension.Document in CMS.


706.10 Bituminous pipe joint filler


If rejecting material because material non-performs or looks defective during use, notify District Testing and OMM, Asphalt Concrete section,

706.11 Resilient and Flexible Gasket Joints


Notify District Testing and OMM, Structural Metals and Welding section, if rejecting material because material non-performs or looks defective during use.

706.12 Resilient and Flexible Joints


Notify District Testing and OMM Structural Metals and Welding section, if rejecting material because material non-performs or looks defective during use.



706.13 Precast Reinforced Concrete Manhole Riser Sections, Catch Basins and Inlet Tops, and Temporary Barriers

Assure products are supplied by a source on the Certified List for S-1073 maintained by OMMReceived with TE-24.Check dimension, markings, roughness or excessive cracks.Document in CMS.

Notify District Testing and OMM, Cement and Concrete section, if rejecting material because material non-performs or looks defective during use.

706.14 Flexible Plastic Gaskets


Notify District Testing and OMM, Structural Metals and Welding section, if rejecting material because material non-performs or looks defective during use.

706.15 Precast Reinforced Concrete Outlets

Assure products are supplied by a source on the Certified List for S-1073 maintained by OMMReceived with TE-24.Check dimension, markings, roughness or excessive cracks.Document in CMS.

Notify District Testing and OMM, Cement and Concrete section, if rejecting material because material non-performs or looks defective during use.

707.01 Metallic Coated Corrugated Steel Conduits and Underdrains[½ inch and 1/4 depth corrugations]

Products will be supplied by a source on the Certified List for S-1019 maintained by OMM.Received with TE-24.Check dimensions and markings.Document in CMS.

Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use.

707.02 Metallic Coated Corrugated Steel Conduits[1 inch depth corrugation]



707.03 Structural Plate Corrugated Steel Structures



707.04 Precoated, Galvanized Steel Culverts

Products will be supplied by a source on the Certified List for S-1019 maintained by OMM.Received with TE-24.Check dimensions and cracks.Document in CMS.

Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use

707.05705.07

Bituminous Coated Corrugated Steel Pipe and Arches with Paved Invert [½ inch depth corrugations][1 inch depth corrugations]



707.10 Steel TubingSquare and Rectangular

Generally a fabricated component received with TE-24.Check dimensions and markings.Document in CMS.




707.11 Mortar Lined Corrugated Steel Pipe[any corrugation depth]



707.12 Corrugated Steel Spiral Rib Conduits



707.13707.14

Bituminous Lined Corrugated Steel Pipe [½ depth corrugations][1 depth corrugations]



707.15 Corrugated Steel Box Culverts



707.21 Corrugated Aluminum Alloy Conduits and Underdrains[1/4, 7/16 & ½ inch depth corrugations]

Products will be supplied by a source on the Certified List for S-1019 maintained by OMM.Received with TE-24.Check dimension and markings.Document in CMS.


707.22 Corrugated Aluminum Alloy Conduits



707.23 Aluminum Alloy Structural Plate Conduits



707.24 Corrugated Aluminum Spiral Rib Conduits



707.25 Corrugated Aluminum Box Culverts





707.31707.32707.33

Polyethylene Corrugated Pipe


Notify District Testing and OMM, asphalt section, if rejecting material because material non-performs or looks defective during use.

707.41 Polyvinyl Chloride Plastic Pipe

If material is shipped with TE24, accept based on inspection of material for type, condition and dimension.Document in CMS.If no TE24, accept based on inspection of material for type, condition, dimension, receipt and verification of manufacturer’s certified test data.Document in CMS


707.42 Polyvinyl Chloride Corrugated Smooth Interior Pipe



707.43 Polyvinyl Chloride Profile Wall Pipe



707.44 Polyvinyl Chloride Sanitary Pipe



707.45 Polyvinyl Chloride Solid Wall Pipe



707.46 Polyvinyl Chloride Drain Waste and Vent Pipe





707.47 ABS and Polyvinyl Chloride Composite Pipe



707.51 ABS Drain Waste and Vent Pipe



707.52 ABS Sewer Pipe If material is shipped with TE24, accept based on inspection of material for type, condition and dimension.Document in CMS.If no TE24, accept based on inspection of material for type, condition, dimension, receipt and verification of manufacturer’s certified test data.Document in CMS


707.70 Welded and Seamless Steel Pipe


Notify District Testing and OMM, structural metals and Welding section, if rejecting material because material non-performs or looks defective during use.

708.01 Inorganic Zinc Silicate Primer Paint

Products will be supplied by a source on the Certified List for S-1084 maintained by OMM.Verify type and brand name of material is on QPL at the time of use.Inspect material container for markings, expiration date and condition.Document in CMS.

Notify District Testing and OMM, chemical section, if rejecting material because material non-performs or looks defective during use. Obtain a 1 qt (1 L) sample representative of the defects.

708.02708.02B708.02C708.02D

OZEU Structural Steel PantOrganic Zinc Prime CoatEpoxy Intermediate CoatUrethane Finish Coat

Products will be supplied by a source on the Certified List for S-1084 maintained by OMM.Verify type and brand name of material is on QPL at the time of use.Inspect material container for markings, expiration date and condition.Document in CMS.

Notify District Testing and OMM, chemical section, if rejecting material because material non-performs or looks defective during use. Obtain a 1 qt (1 L) sample representative of the defects.

709.01 Deformed and Plain Billet Steel Bars for Concrete Reinforcement

Products will be supplied by a source on the Certified List for S-1068 maintained by OMM.Received with TE-24.Check dimension, markings and condition.Document in CMS.

Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain three (3) 30" (.8 m) long samples of each rebar size, with markings, and submit for QA testing by the Laboratory.



709.03 Rail Steel Deformed and Plain Bars for Concrete Reinforcement



709.05 Axle Steel Deformed and Plain Bars for Concrete Reinforcement



709.08 Cold-Drawn Steel Wire for Concrete Reinforcement


Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain three (3) 30" (.8 m) long samples of each diameter and submit for QA testing by the Laboratory.

709.09 Fabricated Steel Bar or Rod Mats for Concrete Reinforcement


Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain 3 ft x 3 ft (1 m x 1 m) of the mat and submit for QA testing by the Laboratory.

709.10 Welded Steel Wire Fabric for Concrete Reinforcement



709.11 Deformed Steel Wire for Concrete Reinforcement





709.12 Welded Deformed Steel Wire Fabric for Concrete Reinforcement



709.13 Coated Dowel Bars


Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain 3 dowel bars and submit for QA testing by the Laboratory.

709.14 Epoxy-Coated Steel Wire and Welded Wire Fabric for Reinforcement



709.15 Plastic Supports for Reinforcing Steel

Products will be supplied by a source on the Approved List maintained by OMM.Inspect for dimension and condition.

Notify District Testing if rejecting material that non-performs or looks defective during use.

709.16 Galvanizing Steel Option for Bridge Spirals



710.01.A710.01 B

Barbed Wire Products will be supplied by a source on the Certified List for S-1067 maintained by OMM.Received with TE-24.Check dimension, markings and condition.Document in CMS.

Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain a 5 ft (1.5 m) length of barbed wire and submit for QA testing by the Laboratory.

710.02 Woven Steel Wire Fence, Type 47


Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain 4 ft (1.2 m) width of fencing and submit for QA testing by the Laboratory.



710.03 Chain-Link Fence[ including Fittings and Accessories]


Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain samples as directed by the Laboratory.

710.06 Deep Beam Rail Products will be supplied by a source on the Certified List for S-1042 maintained by OMM.Received with TE-24.Check dimension, markings and condition.Document in CMS.

Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain three (3) 1 ft (0.3 m) lengths of guardrail from the same section and submit for QA testing by the Laboratory.

710.09 Wire Rope Rail Inspect for dimension, condition, appearance and markings on tag or reel.Submit one (1) six (6) ft. sample to OMM.Document in CMS.

Approval required prior to use. 1Notify District Testing and OMM.

710.11 Fence Posts and Braces[Lumber][Steel]

Products will be supplied by a source on the Certified List for S-1067 and S-1072 maintained by OMM.Received with TE-24.Check dimension, markings and condition.Document in CMS.


710.12 Square-Sawed and Round Guardrail Posts



710.14 Pressure Treated Guardrail and Fence Posts, Braces, and Blocks

Products will be supplied by a source on the Certified List for S-1042 and S-1067 maintained by OMM.Received with TE-24.Check dimension, markings and condition.Document in CMS.


710.15 Steel Guardrail Posts



710.16 Guard Posts Products will be supplied by a source on the Certified List for S-1042 and S-1067 maintained by OMM.Received with TE-24.Check dimension, markings and condition.Document in CMS.




711.01711.04711.07

Structural SteelCold Rolled SteelSteel Castings

Material supplied by a Fabricator source on the Certified List for Items 513, 516, 517 & 518 maintained by OMM.Structural Steel Members are received with TE-24.

If questions concerning structural steel materials, contact OMM Structural Steel Section 1and notify District Testing.

711.02 Galvanized Steel Any material supplied with galvanizing will conform to this specification. Randomly inspect galvanizing for appearance and thickness of coating.


711.03 Steel for Sheet Piling

Certified Mill Test Data required for new material.Verify tensile and chemical properties meet requirements.Inspect all material for dimension and condition.Used material is not acceptable for permanent installations.Document field inspection.

711.08 Arc-welding Electrode & Fluxes

Verify manufacturer is on Approved List maintained by OMM. Inspect for dimension, condition and markings.Document in CMS.

If material is not on Approved List, certification and test data from supplier will be submitted to OMM. Do not use until approval has been received.

711.09 High Strength BoltsNuts and Washers

Received with TE-24.Inspect material for dimension, condition and markings.Reject defective material.Perform field testing of assembly combination per S-1080.Document field inspection & testing in CMS.

If field test does not meet requirements of S 1080, retest bolt, nut and washer combination after application of a lubricant.Notify District Testing if rejecting material.

711.10 Machine Bolts General specification for many common boltsVerify material is component of certified supplier shipment like S-1042 for Guardrail Suppliers or S-1067 for Fence Suppliers.Inspect for condition and coating.Reject defective material.


711.12711.13711.14

Gray Iron CastingsDuctile Iron CastingsGray Iron & Ductile Iron Castings

Verify manufacturer is on Approved List maintained by OMM. Received with TE-24.Inspect for condition and defect.

1Notify District Testing if rejecting material

711.15711.16711.17711.18711.19

Sheet CopperPhosphor Bronze PlateCast BronzeLeaded BronzeSheet Lead

Material supplied by a Fabricator source on the Certified List for Items 513, 516, 517 & 518 maintained by OMM.Structural Steel Members are received with TE-24.Document in CMS.


711.20 Aluminum for Railings

Material supplied by a Fabricator source on the Certified List for Items 513, 516, 517 & 518 maintained by OMM.Structural Steel Members are received with TE-24.Document in CMS.




711.21 Preformed Bearing Pads

Verify type and brand name of material is on QPL at the time of use.Inspect for condition and defect.Verify dimension conform to plan requirements. Document in CMS.

If material non-performs or looks defective during use 1notify District Testing and OMM.

711.23 Elastomeric Bearings

Only accept elastomeric bearings shipped by TE-24.and provided by certified suppliers conforming to S1081. Notify district testing. to Inspect material to check location and number of internal shims utilizing an ice pick or similar tool. Five (5) Durometer Gage readings should be taken and averaged to determine compliance with design plans.Document in CMS.

Field acceptable for durometer. Reading average range: +/- 7 points of design plan number.

711.24 Waterproofing fabric



711.25 Type 2 Membrane Waterproofing


Notify District Testing if rejecting material.If material non-performs or looks defective during use send one (1) 4 ft2 sample representative of defect to OMM for QA follow-up.

711.26 Structural Timber, Lumber and Piling

Products will be supplied by a source on the Certified List for S-1072 maintained by OMM.Received with TE-24 and supplier bill of lading.Check dimension, quantity and condition.Document in CMS.


711.27 Prestressing Steel Material supplied by a Fabricator source on the Certified List for Items 515 maintained by OMM.Prestressed Concrete Members are received with TE-24.

If questions concerning prstressed concrete or prestressed

711.28 Cellular Polyvinyl Chloride Sponge


Notify District Testing if rejecting material.If material non-performs or looks defective during use sendone (1) 1.5'x2.5' sample representative of defect to OMM for QA follow-up.

711.29 Type 3 Membrane Waterproofing

Verify type and brand name of material is on QPL at the time of use.Membrane primer is 705.04 materialInspect for condition and defect.Verify dimension conform to plan requirements. Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use sendone (1) 4 square ft sample representative of defect to OMM for QA follow-up.



711.30 Aluminum for Steps



711.31 Reinforced Propylene Plastic Manhole Steps



712.01 Expansion Shield Anchors


Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain three(3) samples representative of defect to OMM for QA follow-up.

712.02 Calcium Chloride Verify type and brand name of material is on QPL at the time of use.Inspect for condition and defect.Verify dimension conform to plan requirements. Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use contact OMM.

712.03 Sodium Chloride Inspect material for condition.Submit one (1) pint sample per Each Purchase Order to OMM.Document in CMS.

If additional samples required for material quantities exceeding 3000 tons, Notify District Testing.

712.04 A Lime [masonry] Sample & Inspect material for condition with 24 hrs of receipt.One (1) five (5) lb sample for Masonry and Stabilization purposes.One (1) ten (10) lb sample of Quicklime. Send to Geotechnical Engineering.Document in CMS.

Notify District Testing if rejecting material.Samples may be taken in triplicate, if required. Contact Geotechnical Engineering.

712.04 B Lime [Quick] Stabilization

Assure provided material is from suppliers certified under Supplement 1087 and documentation for m S1087 is complete. Document in CMS.If questions on material quality sample.One (1) five (5) lb sample for Masonry and Stabilization purposes.One (1) ten (10) lb sample of Quicklime. Send to Geotechnical Engineering.


712.04 B Lime [Hydrated] Stabilization

Assure provided material is from suppliers certified under Supplement 1087 and documentation for m S1087 is complete. Document in CMS.If questions on material quality sample.One (1) five (5) lb sample for Masonry and Stabilization purposes.One (1) ten (10) lb sample of Quicklime. Send to Geotechnical Engineering




712.04 C Lime [Hydrated] Stabilization

Assure provided material is from suppliers certified under Supplement 1087 and documentation for m S1087 is complete. Document in CMS.If questions on material quality sample.One (1) five (5) lb sample for Masonry and Stabilization purposes.One (1) ten (10) lb sample of Quicklime. Send to Geotechnical Engineering


712.06 Preservative Treatment for Structural Timber

Component material of pressure treated lumber. No approval required.

If questions on pressure treated lumber check the specific material item and follow those instructions

712.09 Geotextile Fabrics Verify type and brand name of material is on QPL at the time of use.Inspect for condition and defect.Verify dimension conform to plan requirements. Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use submit one (1) 4' x 4' sample representative of defect to OMM.

712.10 Prefabricated Edge Underdrain

Inspect material for condition and dimension.Manufacturer’s certified test data required for acceptance.Document in CMS.


712.11 Temporary Erosion Control Mats Material[Types A through I]

Inspect material for condition and dimension.Manufacturer’s certified test data required for acceptance.Field Acceptance itemRefer to Temporary Materials Policy for documentation requirements.


720.01 Rectangular Reflectors

Verify type and brand name of material is on QPL at the time of use.Inspect for condition, color requirements and defect.Verify dimension conform to plan requirements. Document in CMS.


720.03 Flexible Delineator Posts



720.04 Barrier Reflectors Verify type and brand name of material is on QPL at the time of use.Inspect for condition and defect.Verify dimension conform to plan requirements. Document in CMS.


721.01 Raised Pavement Marker Castings

Verify type and brand name of material is on QPL at the time of use.Inspect for condition and defect.Verify type conforms to pre-qualification requirements. Document in CMS.

Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain one (1) 4x2x0.48 in. sample representative of defect to OMM for QA follow-up.



721.02 Prismatic Retroreflector

Verify type and brand name of material is on QPL at the time of use.Inspect for condition and defect.Verify type conforms to pre-qualification requirements. Document in CMS.

Notify District Testing and OMM, structural welding and metals section, if rejecting material because material non-performs or looks defective during use. Obtain one (1) sample representative of defective RPM casting to OMM for QA follow-up.

721.03 Casting Adhesive Verify type and brand name of material is on QPL at the time of use.Inspect for condition and defect.Verify dimension conform to plan requirements. Document in CMS.


721.04 Prismatic Retroreflector Adhesive



725.02 Electrical Cables Verify type and brand name of material is on QPL at the time of use.Inspect for condition, markings and conformance to plan requirements.Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use send a sample representative of non -compliance or defect to OMM for QA follow-up.

725.03 Unit Type Duct-Cable Systems

Verify type and brand name of material is on QPL at the time of use.Inspect for condition, markings and conformance to plan requirements.Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use send a 10 ft. sample representative of non -compliance or defect to OMM for QA follow-up.

725.04 Rigid Ferrous Metal Electrical Conduit and Fittings

Verify type and brand name of material is on QPL at the time of use.Inspect for condition of coating and conformance to plan requirements.Document in CMS.


725.051 Polyvinyl Chloride Conduit and Fittings



725.052 Polyethylene Conduit and Fittings





725.06 Polymer Concrete Pull Boxes

Verify type and brand name of material is on QPL at the time of use.Inspect for condition, dimension, markings and conformance to plan requirements.Document in CMS.


725.07 Plastic Pull Box Verify type and brand name of material is on QPL at the time of use.Inspect for condition, dimension, markings and conformance to plan requirements.Document in CMS.


725.08 Portland Concrete Pull Boxes

Products will be supplied by a source on the Certified List for S-1073 maintained by OMM.Received with TE-24.Check dimension, markings, roughness or excessive cracks.Item 604 Installation documented on CA-P-3 Inspection Form.Document in CMS.

Notify District Testing if rejecting material. If material non-performs or looks defective during use notify District Testing and OMM..

725.10 Junction Boxes Verify type and brand name of material is on QPL at the time of use.Inspect for condition, dimension, markings and conformance to plan requirements.Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use notify District Testing and OMM.

725.11 B Lamps for Luminaires



725.11 E Luminaires for High Intensity Discharge Lamps (including Optical system, lamp, ballast and housing)



725.11 F Wall Mounted Underpass Luminaires (including Optical system, lamp, ballast and housing)



725.11 G High Mast/Low Mast Luminaire (including Optical system, lamp, ballast and housing)





725.12 Polyethylene, Fiberglas reinforced, Pull Box with Polymer concrete cover and support ring



725.15 Circuit Cable Connections and terminations



725.16 Ground Rods Verify type and brand name of material is on QPL at the time of use.Inspect for condition, dimension, markings and conformance to plan requirements.Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use contact OMM.

725.19 I Power Service ComponentsWood Pole

Products will be supplied by a source on the Certified List for S-1072 maintained by OMM.Received with TE-24 and supplier bill of lading.Check dimension, quantity and condition.Document in CMS.


725.20 Multiple Cell Polyvinyl Chloride Conduit and Fittings



725.21 A Luminaire SupportsLight Poles

Inspect material for condition and conformance to plan requirements.Verify pole provided by Certified Manufacturer under Supplement 1091.Accept with TE-24Document in CMS


725.21 B Luminaire SupportsLight Towers

Inspect material for condition and conformance to plan requirements.Verify pole provided by Certified Manufacturer under Supplement 1091.Accept with TE-24.Document in CMS.


725.21B9 Luminaire SupportAnchor Bolts

OPTION 1Verify type and brand name of material is on QPL at the time of use.Inspect for condition, and conformance to plan requirements.OPTION 2Verify pole provided by Certified Manufacturer under Supplement 1091.Accept with TE-24.Document in CMS.


730.01 Steel Tube and Pipe

This item typically is a component of a sign support. Inspect total component for condition and conformance to shop drawings. Document in CMS




730.015 U-Channel Posts Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use notify District testing and OMM.

730.016 Square Posts Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


730.02 Steel Anchor Bolts and Nuts

OPTION 1Verify type and brand name of material is on QPL at the time of use.Inspect for condition, and conformance to plan requirements.OPTION 2Verify pole provided by Certified Manufacturer under Supplement 1093.Accept with TE-24.Document in CMS.


730.03 Steel Poles and Arms

Component material provided by Certified Manufacturer under Supplement 1093. Verify manufacturer is on 1093.Accept with TE-24.Document in CMS.


730.04 Base and Arm Plates

Component material provided by Certified Manufacturer under Supplement 1093. Verify manufacturer is on 1093.Accept with TE-24.Document in CMS.


730.05 Handhole Covers Component material provided by Certified Manufacturer under Supplement 1093. Verify manufacturer is on 1093.Accept with TE-24.Document in CMS.


730.06 Pole Caps Component material provided by Certified Manufacturer under Supplement 1093. Verify manufacturer is on 1093.Accept with TE-24.Document in CMS.


730.07 Arm Caps Component material provided by Certified Manufacturer under Supplement 1093. Verify manufacturer is on 1093.Accept with TE-24.Document in CMS.


730.08 Steel Hardware Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093.Accept with TE-24.Document in CMS.




730.09 Stainless Steel Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093.Accept with TE-24.Document in CMS.


730.10 Stainless Steel Hardware

Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093Accept with TE-24.Document in CMS.


730.11 Aluminum Sheet and Plate

Component material provided by Certified Manufacturer under Supplement 1092 or 1093. Verify manufacturer is on 1092 or 1093.Accept with TE-24.Document in CMS.


730.12 Aluminum Extrusions



730.13 Aluminum Tube and Pipe



730.14 Aluminum Castings



730.15 Aluminum Forgings



730.16 Aluminum Welding Rods

Normally only applies to shop fabrication. If performing field aluminum welding contact District Testing and OMM for recommendations.


730.17 Aluminum Hardware

Component material provided by Certified Manufacturer under Supplement 1092.Verify manufacturer is on 1092.Accept with TE-24.Document in CMS.


730.18 Reflective Sheeting Type F

Use if certification provided. Document in CMS.

Notify District Testing if rejecting material.If material non-performs or looks defective during use notify District Testing and OMM..



730.19 Reflective Sheeting Type G

Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


730.191 Reflective Sheeting Type G rebondable



730.192 Reflective Sheeting Type H



730.193 Reflective Sheeting Type J



730.20 Nonreflective Sheeting



730.22 Silk Screen Inks No field acceptance requirements.- part of 730.19,191,192 or 193 items.

730.23 Transparent Electronic Cuttable Films

No field acceptance requirements.- part of 730.19,191,192 or 193 items No field requirements.

731.01 Mercury Vapor Luminaire



731.03 Changeable Message Sign, Electrical Type



731.05 Internally Illuminated Fixed Message Sign



731.06 Sign Flasher Assembly





731.07 School Speed Limit Sign Assembly



731.08 Flexible Conduit Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


731.10 Timer with Enclosure



732.01 Vehicular Signal Heads, Conventional



732.02 Vehicular Signal Heads, Optically Programmed, 12-inch (300 mm) Lens



732.03 Vehicular Signal Heads, Optically Programmed, 8-inch (200 mm) Lens



732.04 A Optically ProgrammedAnd Pedestrian Incandescent Signal Lamps



732.04 B Vehicular Signal Incandescent Lamps



732.04 C Vehicular and pedestrian light Emitting Diode Lamps



732.05 Pedestrian Signal Heads[Type A1][Type A2][Type D2]





732.06 Pedestrian Pushbuttons



732.07 A Loop Detector Units Nema TS 1



732.07 B Loop Detector Units Nema TS 2



732.08 Loop Detector Units, Delay and Extension Type



732.09 Magnetometer Detector Units



732.10 Magnetometer Sensor Probes



732.11 Signal Supports Check provided by Certified Manufacturer under Supplement 1094 Accept with TE-24.Document in CMS.


732.12 Strain Poles Check provided by Certified Manufacturer under Supplement 1094 Accept with TE-24.Document in CMS.


732.13 Wood Poles Check provided by Certified Manufacturer under Supplement 1072 Accept with TE-24.Document in CMS.


732.14 Down Guy Assemblies





732.15 Pedestals Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


732.16 Conduit Risers See 725.04 requirements. Notify District Testing if rejecting material.If material non-performs or looks defective during use notify District Testing and OMM.

732.17 Cable Support Assemblies



732.18 Messenger Wire Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


732.19 Cable and Wire Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


732.20 Power Service See 725.04 requirements Notify District Testing if rejecting material.If material non-performs or looks defective during use notify District Testing and OMM.

732.21 Disconnect Switch with Enclosure



733.02 A Controller Unit Type TS2/A1



733.02 B Controller Unit Type TS2/A2



733.02 C Controller Unit Type 170E





733.02 D Controller Unit Type 2070L and LC



733.03 A Cabinet Type TS 1 Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


733.03 B Cabinet Type TS 2 Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


733.03 C Cabinet Type 332 Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


733.03 D Cabinet Type 334 Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


733.03 E Cabinet Type 336 Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


733.04 A Cabinet Riser for TS 1 – TS 2 cabinet

Field inspect for 1/4 aluminum thickness and accept.


733.04 B Cabinet Riser for Types 332, 334 or 336



733.05 Flasher Controller Verify type and brand name of material is on QPL at the time of use.Inspect for conformance to dimension and condition.Document in CMS.


733.06 Controller, Master, Traffic Responsive

Assure the same manufacturer as the supplied controller unit 733.02.


733.07 Remote Monitoring Station

Compatible with the supplied 733.02 and 733.06 unit.




740.02 Traffic Paint Verify material is on Approved List maintained by OMM.Accepted with TE-24.Inspect container for appropriate markings. Inspect material for uniform consistency.Document in CMS.

If rejecting for performance provide 1 qt (1 L) sample and notify District.

740.03 Polyester Pavement Marking

Verify material is on Approved List maintained by OMM.Accepted with TE-24.Inspect container for appropriate markings. Inspect material for uniform consistency.Document in CMS.


740.04 Thermoplastic Pavement Marking



740.05 Preformed Pavement Marking



740.06 Work Zone Pavement Marking[Type 1 Removable][Type 2 Non-Removable]

Materials accepted by Engineer.Inspect material for uniform consistency.Document in CMS.


740.07 Epoxy Pavement Marking Material


If rejecting for performance provide 1 qt (1 L) sample and notify District

740.08 Heat-Fused Preformed Plastic Pavement Marking Material


If rejecting for performance provide 1 qt (1 L) sample and notify District



740.09 A Glass Beads – for 740.02



740.09 B Glass Beads – for 740.03



740.09 C Glass Beads – for 740.04



740.09 D Glass Beads – for 740.07



748.01 Ductile Iron Pipe, Joints, and Fittings



748.02 Polyvinyl Chloride (PVC) Pipe, Joints, and Fittings



748.03 Polyethylene (PE) Service Branches and Fittings



748.05 Copper Service Branches and Fittings



748.06 Steel Pipe Encasement

Basis of acceptance is certified test data containing documentation of domestic origin from manufacturer.

Notify District Testing if rejecting material



748.07 Polyethylene Encasement

Verify manufacturer certification conforms to ANSI/AWWA C105/A21.5Inspect condition, dimension, suitability for intended use.


748.08 Gate Valve and Valve Box



748.09 Inserting Valve and Valve Box



748.10 Cutting-in Sleeve, Valve, and Valve Box



748.11 Tapping Sleeve, Valve, and Valve Box



748.12 Tapping Saddle and Corporation Stop



748.13 Service Stop and Service Box



748.14 Meter, Setting, Stop, and Chamber

Inspect for condition, dimension, suitability for intended use.Acceptance based on manufacturer’s statement of conformity.

748.15 Fire Hydrant Verify type and brand name of material is on QPL at the time of use.Inspect for condition, dimension, suitability for intended use.Document in CMS.


2010 c&ms - ohio department of transportation · web viewseeding and mulching - hydrated lime...

Documents