2011 ford f150 supercharger

Upload: mfcramer

Post on 03-Apr-2018

237 views

Category:

Documents


0 download

TRANSCRIPT

  • 7/29/2019 2011 Ford f150 Supercharger

    1/41

    Step 1

    Disconnect negative terminal from

    battery using 8 mm wrench.

    Step 2

    Drain cooling system by un-screwing the drain

    plug on the passenger of the radiator. This is

    best accessed through the fender well.

    Attaching a length of 5/16 ID hose to the drain

    nipple will help guide the coolant into the

    container.

    R Removing the coolant bottle cap

    will aid in the draining of the coolant. Once

    drained, replace the drain plug and the

    coolant bottle cap.

  • 7/29/2019 2011 Ford f150 Supercharger

    2/41

    Step 3Cover the tops of the fenders and the

    bumper with protective wrap.

    Step 4

    Loosen screws on the band clamps on both ends of air intake duct. Remove PCV hose from air

    intake duct. Remove break booster hose from air intake duct. Remove entire air intake duct

    from engine.

    jjkj

  • 7/29/2019 2011 Ford f150 Supercharger

    3/41

    Step 5

    Disconnect throttle body electrical connector.you will need to slide the red lock sideways first

    in order to remove the connector.

    Step 6

    Disconnect purge valve electrical connector.

    Step 7

    Disconnect PCV hose connection at the

    intake manifold.

  • 7/29/2019 2011 Ford f150 Supercharger

    4/41

    Step 8

    Disconnect heater hose connection on

    drivers side of engine and move the hose

    close to the battery, out of the way.

    Step 9

    Disconnect purge valve hose and hose

    support and move hose out of way.

  • 7/29/2019 2011 Ford f150 Supercharger

    5/41

    Step 10

    Remove drives side fuel rail insulation.

    Step 11

    Remove passenger side fuel rail insulation.

    Step 12

    Disconnect brake booster hose connection.

  • 7/29/2019 2011 Ford f150 Supercharger

    6/41

    Step 13

    Disconnect fuel line connection at the fuel rail.

    be careful to protect against fuel spray, as there

    may be pressure in the fuel system.

    Step 14

    Remove the four bolts that secure the fuel

    rail assembly to the intake manifold,

    using a 10 mm socket.

    Step 15

    Disconnect the eight injector connector

    from the injectors.

    Step 16

    Remove the fuel rail assembly with the injectors.

  • 7/29/2019 2011 Ford f150 Supercharger

    7/41

    Step 17

    Loosen the six intake manifold bolts

    using an 8 mm socket.

    Note: The bolts do not come out of

    the intake manifold assembly.

    Step 18

    Remove intake manifold assembly from engine.

    Step 19

    Remove all eight injectors by first removing

    the injector retaining clip with a screwdriver.

  • 7/29/2019 2011 Ford f150 Supercharger

    8/41

    Step 20

    Install new injectors using a small amount of

    petroleum jelly to lubricate O-Rings.

    Step 21

    Re-install injector retainer clips.

    Step 22

    Install fuel rails as shown in photo,

    pushing injectors down into seats.

  • 7/29/2019 2011 Ford f150 Supercharger

    9/41

    Step 23

    Install four M6 X 80 mm SHCS and M6

    washer onto the injector bracket hole.

    Step 24

    Remove the eight intake seals from the

    stock intake.

    Step 25

    Install the eight intake seals into the grooves

    on the supercharger intake manifold.

  • 7/29/2019 2011 Ford f150 Supercharger

    10/41

    Step 26Remove the four bolts retaining the throttle

    body onto the stock intake using 8 mm socket.

    Step 27

    Remove the stock seal from the original

    intake manifold using 8 mm socket.

    Step 28

    Remove the two bolts securing the purge valve

    to the stock intake manifold using an 8 mm socket.

  • 7/29/2019 2011 Ford f150 Supercharger

    11/41

    Step 29

    Remove the bolt securing the PCV nipple to the

    stock intake using an 8 mm socket.

    Step 30

    Using a utility knife, cut the plastic fuel

    line, where it attaches to the steel line

    at the firewall. Remove the plastic line.

    Step 31

    Cut the plastic line with a utility knife where

    it attaches to the fuel rail connector, and

    discard the plastic line.

  • 7/29/2019 2011 Ford f150 Supercharger

    12/41

    Step 32

    Connect the supplied 5/16 fuel line to the

    fuel rail connector, and install the supplied

    fuel hose clamp and tighten.

    Step 33

    Connect the other end of the supplied fuel

    line to the steel fuel line at the firewall, and

    install the supplied fuel hose clamp and

    tighten.

    Step 34

    Remove the protective tape from

    the rear of the supercharger.

  • 7/29/2019 2011 Ford f150 Supercharger

    13/41

    Step 35

    Install the supplied vacuum nipple to the

    intake manifold using a small amount of

    red threadlocker.

    Step 36

    Install the supplied O-Ring to the rear of the

    supercharger. A small amount of petroleum

    jelly may help in holding the O-Ring in place.

    Step 37

    Install the inlet elbow at the rear of the

    supercharger.

  • 7/29/2019 2011 Ford f150 Supercharger

    14/41

    Step 38

    Install the three M8 X 25 SHCS and M8

    washers and tighten.

    Step 39

    Install the M8 hex nut onto the stud and

    tighten with a 13mm wrench.

    Step 40

    Install the PCV nipple and secure with the

    supplied M6 X 16 SHCS and M6 washer.

  • 7/29/2019 2011 Ford f150 Supercharger

    15/41

    Step 41

    Connect supplied vacuum line to the

    bypass valve nipple.

    Step 42

    Connect other end of vacuum line to the

    nipple on upper rear of intake manifold.

    Step 43

    Installed supplied NPT elbow to inlet elbow

    using a small amount of red thread locker.

  • 7/29/2019 2011 Ford f150 Supercharger

    16/41

    Step 44

    Install supplied brake booster hose nipple

    onto the NPT elbow using a small amount

    of red threadlocker.

    Step 45

    Install purge valve onto intake elbow with

    original bolts using an 8 mm socket.

    Step 46

    Loosen the knock sensor bolts and adjust the rotation of the sensors to place them

    as close as possible to the cylinder heads. It may be necessary to remove some of the

    wire harness cover between the two sensors in order to rotate the sensors to the correct

    location. Torque the sensors to 177 lb / in (20 Nm).

  • 7/29/2019 2011 Ford f150 Supercharger

    17/41

    Step 47

    Install the supercharger/intake manifold assembly onto the engine. This is a tight fit, so go

    slowly. Once in place, the fuel rail bolts should start into the threaded holes on the cylinderheads.

    Step 48

    Tighten the four M6 X 80mm SHCS securing

    the fuel rails, using an M4 allen socket.

  • 7/29/2019 2011 Ford f150 Supercharger

    18/41

    Step 49

    Install the six M6 X 40mm SHCS and M6 washers

    into the intake manifold and tighten using an

    M4 allen socket.

    Step 50

    Connect the eight fuel injector

    electrical connectors.

    Step 51

    Remove the two thermostat housing bolts

    using an 8mm socket.

  • 7/29/2019 2011 Ford f150 Supercharger

    19/41

    Step 52

    Remove the two water outlet housing

    bolts using a 10mm socket.

    Step 53

    Remove the radiator hose from the

    water outlet housing with

    adjustable pliers.

    Step 54

    Remove the original hose clamp from the

    radiator hose. The clamp is bonded to the

    hose, so you must carefully cut the clamp

    away from the hose.

  • 7/29/2019 2011 Ford f150 Supercharger

    20/41

    Step 55

    Install the hose onto the water outlet

    housing, using the supplied HS24 hose

    clamp. Note: How the hose sits

    approximately inch further out

    on the outlet housing.

    Tighten clamp.

    Step 56

    Release tensioner with a Johnson

    bar and a 15mm socket. Remove

    the drive belt.

    Step 57

    Remove top water pump bolt using

    a 10mm wrench.

  • 7/29/2019 2011 Ford f150 Supercharger

    21/41

    Step 58

    Remove water pump pulley bolts usinga 10mm socket. Remove pulley.

    Step 59

    Install supercharger belt idler pulley

    and bracket using a 6mm allen socket.

    Step 60

    Re-install water pump pulley using

    a 10mm socket.

  • 7/29/2019 2011 Ford f150 Supercharger

    22/41

    Step 61

    Install supercharger drive belt

    per diagram.

    Step 62Install O-Ring on water pump outlet

    spacer using a small amount of

    petroleum jelly to hold the O-Ring

    in place during assembly.

    Step 63

    Install spacer between water pump outlet

    and water pump with the O-Ring towards

    the engine using the M6 X 75mm SHCS and

    6mm washers. Tighten with 4mm allen

    socket.

  • 7/29/2019 2011 Ford f150 Supercharger

    23/41

    Step 64

    Re-install water outlet housing to drivers

    side cylinder head using 10mm socket.

    Check for adequate clearance between

    radiator hoses and supercharger drive

    belt.

    Step 65

    Re-connect heater hose to drivers

    side head, routing the hose over

    the supercharger.

    Step 66

    Remove passenger side PCV hose from

    valve cover and cut tube on both ends

    to enable hose to be removed from thefittings.

  • 7/29/2019 2011 Ford f150 Supercharger

    24/41

    Step 67

    Push PCV fittings onto each end of supplied

    5/8 ID hose. Install heat shrink bands to

    secure hose ends using a heat gun to shrink

    the bands into place.

    Step 68

    Install one end of PCV hose onto nipple

    on passenger valve cover and installother end onto PCV nipple located on

    supercharger inlet elbow.

    Step 69

    Install original throttle body seal into

    groove in supercharger inlet elbow.

  • 7/29/2019 2011 Ford f150 Supercharger

    25/41

    Step 70

    Install throttle body onto inlet elbow

    using original bolts and an 8mm socket.

    Step 71

    Cut brake booster hose to shorten

    length in order to connect to barb

    fitting on supercharger inlet elbow.

    Step 72

    Push hose onto barb and retain using

    original clamp.

  • 7/29/2019 2011 Ford f150 Supercharger

    26/41

    Step 73

    Cut hose at end of purge valve line,

    in order to remove purge valve fitting.

    Step 74

    Cut purge valve hose shorter and

    connect purge valve fitting. Connect

    purge valve line to purge valve.

    Step 75

    Cut throttle body wiring approx. 6 inches

    back from connector.

  • 7/29/2019 2011 Ford f150 Supercharger

    27/41

    Step 76

    Cut purge valve wiring approx. 6 inches

    back from connector.

    Step 77

    Use supplied wiring extensions and

    connectors to lengthen the throttle

    body harness and the purge valve

    harness.

    Step 78

    Use supplied split loom to cover wiring

    once extensions have been spliced in.

  • 7/29/2019 2011 Ford f150 Supercharger

    28/41

    Step 79

    Route wiring for throttle body and purge valve down passenger side valve cover,

    around rear of supercharger and connect each to proper connector. Secure wiring

    loom with supplied tie wraps.

    Step 80

    Connect intake sensor harness suppliedto the IAT sensor on the rear of the

    supercharger intake.

    Step 81

    Route the wiring towards the air filter

    box. Connect the blue wire from the

    mass air flow sensor wire harness using

    the supplied scotchlock connector.

  • 7/29/2019 2011 Ford f150 Supercharger

    29/41

    Step 82

    Cut the purple wire in the mass air flow sensor

    wire harness and connect the purple wire from

    the intake air sensor harness to the purple

    wire on the wire harness. Seal the harness with

    supplied electrical tape. Cover wiring with

    supplied split loom and secure harness with

    supplied tie wraps.

    Step 83

    Install air inlet ducts and tubing connectors as shown in photos. Attach with supplied

    HS56 hose clamps and tighten with screwdriver.

    Step 84

    Connect supplied 5/8 PCV hose to two

    supplied PCV connectors as shown in

    photo.

  • 7/29/2019 2011 Ford f150 Supercharger

    30/41

    Step 85 (no photo)

    Use supplied heat shrink tubing to Step 86 photo

    secure PCV hose to connectors.

    Step 86

    Install completed PCV hose assembly as

    shown in photo.

    Step 87

    Install intercooler water pump onto heat

    exchanger as shown in photo using

    supplied HS36 hose clump. Tighten

    clamp with a screwdriver.

    Step 88

    Cut approx. 2 inches off short leg of

    supplied hose.

  • 7/29/2019 2011 Ford f150 Supercharger

    31/41

    Step 89

    Install hose as shown in photo using supplied

    HS12 hose clamps. Tighten clamps with a

    screwdriver.

    Step 90

    Remove two upper front bumper bracket

    bolts using 13/16 socket.

    Step 91

    Remove horn bracket mounting bolt using

    10mm socket.

  • 7/29/2019 2011 Ford f150 Supercharger

    32/41

    Step 92

    Bolt heat exchanger to upper radiator (no photo)

    support using the original bolt and a

    10mm socket.

    Step 93

    Drill 3/16 hole in upper radiator support

    being careful to ensure the heat

    exchanger is level.

    Step 94

    Use supplied X 1 self tapping screw

    and fender washer to mount drivers

    side upper strap to radiator support using

    an 11mm socket.

  • 7/29/2019 2011 Ford f150 Supercharger

    33/41

    Step 95

    Tighten original upper bumper nuts

    to secure lower heat exchanger

    brackets using 13/16 socket.

    Step 96

    Photo shows installed heat exchanger.

    Step 97

    Bolt horn bracket on to passenger side

    upper heat exchanger bracket using

    supplied X 1 bolt, nylock nut and

    washers with an 11mm socket.

  • 7/29/2019 2011 Ford f150 Supercharger

    34/41

    Step 98

    Drill holes into radiator shroud using

    3/16 drill bit to mount intercooler

    bottle bracket.

    Step 99

    Rivet bracket in place using 3/16

    supplied rivets.

    Step 100

    Bolt bottle to bracket using M6 X 25

    bolt and washer.

  • 7/29/2019 2011 Ford f150 Supercharger

    35/41

    Step 101

    Cut a 30 inch length of hose from the supplied hose, connect one end of hose

    to lower nipple of intercooler bottle and the other end to intercooler pump.

    Secure with supplied HS12 hose clamps and tighten with screwdriver.

    Step 102

    Cut an 18 inch length of hose and a 3 inch length of hose from the supplied hose.

    Connect one end to upper nipple of intercooler bottle and the other end to the 90 degree

    fitting. The 3 inch hose connects the other side of the 90 degree fitting to the vertical

    intercooler nipple on the front of the intake manifold. Use supplied HS12 hose clamps to

    secure the hoses. Tighten with a screwdriver.

  • 7/29/2019 2011 Ford f150 Supercharger

    36/41

    Step 103

    Cut a 32 inch length of hose and a 3 inch length of hose and a 6 inch length of hose

    from the supplied hose. Connect the 3 inch piece on one end of the 32 inch hose using a

    supplied 90 degree fitting and the 6 inch piece on the other end of the 32 inch hose. Connect

    the 6 inch hose to the lower heat exchanger nipple and the 32 inch hose through the radiator

    support to route. Connect the 3 inch hose to the 45 degree intercooler nipple located at thescrewdriver.

    Step 104

    Using a trim tool, remove the upper

    radiator support trim panel.

  • 7/29/2019 2011 Ford f150 Supercharger

    37/41

    Step 105

    Drill a 3/16 hole in the passenger side

    fuse box bracket next to the hole for

    the trim clip.

    Step 106

    Attach the relay using the supplied

    3/16 rivet.

    Step 107

    Connect the 10 gauge red wire with the

    male spade connector to the lower left

    pin in cavity 9.

  • 7/29/2019 2011 Ford f150 Supercharger

    38/41

    Step 108

    Connect the ring terminal of the 10 gauge

    red wire to the positive terminal inside

    the fuse box. Tighten nut with a 10mm

    socket.

    Step 109

    Connect ground wire ring terminal to

    negative terminal of battery cable

    using a 10 mm socket.

    Step 110

    Connect water pump electrical connector

    to the water pump and route wiring close

    to radiator support. Use tie wraps tosecure wiring.

  • 7/29/2019 2011 Ford f150 Supercharger

    39/41

    Step 111

    Re-install upper radiator support

    trim panel using original trim clips.

    Step 112

    Connect negative terminal to battery,

    tighten with 8mm socket.

    Step 113

    Connect handheld programmer to OBD connector under dash. Follow directions on

    programmer to install custom tune. Ensure battery is fully charged before starting download.

  • 7/29/2019 2011 Ford f150 Supercharger

    40/41

    Step 114

    Fill radiator bottle with 50/50 mixture

    of Ford antifreeze and water.

    Step 115

    Fill intercooler bottle with 50/50 mixture of Ford antifreeze and water. Turn ignition key to

    run position and verify that the coolant is circulating through bottle.

    Step 116

    Fill truck with 91 octane fuel. Start engine and warm up truck fully. Check fluid levels.

  • 7/29/2019 2011 Ford f150 Supercharger

    41/41