213.250.6069 dmx system installation guide...2 of 21 213.250.6069 infoopticarts.com optic arts 2018...
TRANSCRIPT
-
1 of 21
213.250.6069
www.opticarts.com
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDENOTES
Please read entire guide prior to starting installation.
1. All installations shall be executed in accordance with local building codes.
2. The installing contractor assumes all liability for the safety and code compliance of the
installation.
3. Optic Arts is not liable for any damages caused by improper wiring, circuit overloading,
power surges, system design or layout, negligence, or other conditions.
DMX SYSTEM STANDALONE MODE
UL LISTED ENCLOSURE (BY OTHERS)
DMX MODULE
DMX MODULE
®®
24V DC+
24V DC+
24V DC-
24V DC-
LED+CH1 -CH2 -CH3 -CH4 -
LED+CH1 -CH2 -CH3 -CH4 -
GG
100E
-24-
UN
V
GG
100E
-24-
UN
VLED+
LED+
R
R
G
G
B
B
W/A
W/A
OUT TO NEXT MODULE
LEDSync thru +LEDSync thru -LEDSync shield
DMX in +
LEDSync thru +LEDSync thru -
DMX in -DMX in shield
LEDSync shield
DMX Cabling such as Belden 9841 (or similar):
• Blue > DMX+• White > DMX–• Shield > Common
-
2 of 21
213.250.6069
www.opticarts.com
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
DMX System With DMX Controller
Diagram #1 Diagram #2
DMX System with DMX Controller
and Power Supply
UL LISTED ENCLOSURE (BY OTHERS)
UL LISTED ENCLOSURE (BY OTHERS)
DMX MODULE DMX MODULE
DMX MODULE DMX MODULE
® ®
® ®
24V DC+ 24V DC+
24V DC+
24V DC+ 24V DC+
24V DC- 24V DC-
24V DC-
24V DC- 24V DC-
LED+CH1 -CH2 -CH3 -CH4 -
LED+CH1 -CH2 -CH3 -CH4 -
LED+CH1 -CH2 -CH3 -CH4 -
LED+CH1 -CH2 -CH3 -CH4 -
LED+ LED+
LED+ LED+
R R
R R
G G
G G
B B
B B
W/A W/A
W/A W/A
CTRLDMX.4CH.3S.W(OR BY OTHERS)
CTRLDMX.4CH.3S.W(OR BY OTHERS)
OUT TO NEXT MODULE OUT TO NEXT MODULE
DMX Cabling such as Belden 9841 (or similar)*: DMX Cabling such as Belden 9841 (or similar)*:Blue > DMX+ Blue > DMX+White > DMX– White > DMX–Shield > Common Shield > Common
DMX in +
LEDSync thru +
LEDSync thru -
DMX in -
DMX in shield
LEDSync shield
DMX in +
LEDSync thru +
LEDSync thru -
DMX in -
DMX in shield
LEDSync shield
DMX in +
LEDSync thru +
LEDSync thru -
DMX in -
DMX in shield
LEDSync shield
DMX in +
LEDSync thru +
LEDSync thru -
DMX in -
DMX in shield
LEDSync shield
CTRLDMX.4CH.3S.W(OR BY OTHERS)
CTRLDMX.4CH.3S.W(OR BY OTHERS)
GND GNDD+ D+D- D-V+ V+V- V-
GG
100E
-24-
UN
V
GG
100E
-24-
UN
V
GG
100E
-24-
UN
V
GG
100E
-24-
UN
V
LV10-24N-120-A(OR BY OTHERS)
(Mounted in junction box)120VAC
-
3 of 21
213.250.6069
www.opticarts.com
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
1.
1.1 Identify mounting location for driver & eldoLED® LinearDrive100D(s). eldoLED® LinearDrive100D(s) must be mounted in a UL listed Junction Box (by others).
1.2 Remove faceplate cover.
1.3 Mount eldoLED® LinearDrive100D(s) in a UL listed Junction Box (by others).
1.4 Remove strain relief pieces.
Strain Relief Strain Relief
WIRING INSTALLATION
-
4 of 21
213.250.6069
www.opticarts.com
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
2.
2.1 Wire 24VDC into eldoLED® LinearDrive100D(s) using the GG100E-24-UNV(s) through UL Listed conduit(s).
ELECTRONICDRIVER
UL Listed Enclosure (By Others)(Repeat step for additional drivers)
(Repeat step for additional modules)
24V DC+
24V DC-
Page must be printed in color.
-
5 of 21
213.250.6069
www.opticarts.com
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDEWIRING INSTALLATION
3.
3.1 Connect lead wires from light fixture or tape, as applicable to the product
being installed.
LED+
LED+
LED+
LED+LED-
R
R
C*
G
G
W
• FLEX RGBA/W
• FLEX VW
• FLEX Single Color
• FLEX RGB
FLEX WIRING:
B
B
W/A
24V DC-
24V DC+
GG100E-24-UNV
* Wire is either white or red, depending on specific product.
Page must be printed in color.
-
6 of 21
213.250.6069
www.opticarts.com
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
• FLEX RGBA/W
• FLEX VW
• FLEX Single Color
• FLEX RGB
VISUAL TEST:
On Screen: At Fixture:
No Light
No Light
No Light
No Light
No Light
No Light
4.
4.1 Run visual test by tapping the three control buttons simultaneously.
4.2 If LEDs on fixture flash in sequence shown on display, the eldoLED® LinearDrive100D is successfully installed.
M — ++ +(See Visual Test)(Press at the same time)
TEST Display Off
*Color specified will flash
2x R
G
B
W
RGBW
2x
2x
2x *
*
R
R
R
G
G
G
B
B
B
W
W
W
RGBW
RGBW
RGBW
If any control channels are not functioning, turn to next page to troubleshoot the malfunctioning FLEX product.
Page must be printed in color.
-
7 of 21
213.250.6069
www.opticarts.com
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
4. Cntd. TROUBLESHOOTING MALFUNCTIONING FLEX PRODUCT
A. If none of the FLEX LEDs are turning on, tap M button to see if display on eldoLED® Linear100D will turn on.
Follow step by step until issue is resolved.
• If display does not turn on, turn to next page to review TROUBLESHOOTING MALFUNCTIONING eldoLED® Linear100D.
• If display does turn on, move on to next step.
M M M M+ LED EXT INP DIM CURVLED Groups
(Click + or - to change)
B) LED GROUPS
Single Color
RGBRGBW
Variable White
External Input Dimming Curve
Display Off
1-1L2-2L3-3L4-4L2-4L1-4LRGB
RGBWRGBARRGBRGGBCCWWCWWW
OFFPOTM10VSWIT
LOGLIN
M M MM M
C) SINGLE COLOR C Cntd.) VARIABLE WHITEChannel 1 (Cool)Channel 1 Channel 2 (Warm)
Display Off Display Off
Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity
OR OR OR
M M M M
C Cntd.) RGBChannel 1 (Red) Channel 2 (Green) Channel 3 (Blue)
Display Off
Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity
OR OR OR
M M M M M
C Cntd.) RGBA/WChannel 1 (Red) Channel 2 (Green) Channel 3 (Blue) Channel 4 (Amber/White)
Display Off
Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity
OR OR OR OR
B. Program eldoLED® Linear100D to relevant Color Group to match LED setup. Hold to switch to color.
C. Raise the intensity of the first color to ensure that a FLEX color correlates with the channel. Lower the intensity to lowest setting, and repeat with next channel until each color has been verified.
• If FLEX color does not match its corresponding channel, rewire and retest each channel. Once FLEX color matches corresponding channel, reset DMX module and move on to Step 5 (pg. 9)
• If any channel is not functioning, check wiring, and retest each channel. If channel error persists, contact Optic Arts at (213) 250-6069.
M Display Off
Reset to Factory Defaults
M — ++ + RESETPRESS MENU
Reset(Press & hold for 5 sec)
OPTIC ARTS PRO TIP:If eldoLED® Linear100D continues to malfunction, refer to Reset To Factory Default.
M
-
8 of 21
213.250.6069
www.opticarts.com
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
4. Cntd.TROUBLESHOOTING MALFUNCTIONING eldoLED® Linear100D
A. Hold down all three buttons for 5 seconds to reset eldoLED® Linear100D. If eldoLED® Linear100D display does not turn on, move on to next step.
B. Wire a different eldoLED® Linear100D to same driver. If eldoLED® Linear100D display does not turn on, repeat Step A with multiple eldoLED® Linear100D modules. If multiple eldoLED® Linear100D displays still do not turn on, move on to next step.
C. Wire eldoLED® Linear100D to another driver. Driver must be off first. Do not wire hot. If eldoLED® Linear100D display does not turn on, repeat Step A with multiple eldoLED® Linear100D modules on the most current driver. If multiple eldoLED® Linear100D
displays do not turn on, turn to next page to review TROUBLESHOOTING MALFUNCTIONING ELECTRONIC DRIVER.
Follow step by step until issue is resolved.
-
9 of 21
213.250.6069
www.opticarts.com
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
4. Cntd.TROUBLESHOOTING MALFUNCTIONING ELECTRONIC DRIVER
A. Wire one channel of FLEX product directly into ELECTRONIC DRIVER. If FLEX product does not turn on, move on to next step.
B. Wire the same channel of FLEX product to a different ELECTRONIC DRIVER. If FLEX product still does not turn on, repeat Step A & B with a different FLEX channel or FLEX product. If FLEX product still does not turn on, check input power to driver(s) (120/277 VAC).
• If issue is found with input power, resolve issue and return to Step 2 (pg. 3).
• If input power is not the issue, contact Optic Arts at (213) 250-6069 to replace ELECTRONIC DRIVER(s).
DRIVER MUST BE OFF FIRST - DO NOT WIRE HOT
Follow step by step until issue is resolved.
-
10 of 21
213.250.6069
www.opticarts.com
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
5 STANDALONE.M M M M+ LED EXT INP DIM CURV
LED Groups(Click + or - to change)
Single Color
RGBRGBW
Variable White
External Input Dimming Curve
Display Off
1-1L2-2L3-3L4-4L2-4L1-4LRGB
RGBWRGBARRGBRGGBCCWWCWWW
OFFPOTM10VSWIT
LOGLIN
M M
C) SINGLE COLOR
Channel 1
Display Off
Hold to Change Intensity
OR M M M
C Cntd.) VARIABLE WHITE
Channel 1 (Cool) Channel 2 (Warm)
Display Off
Hold to Change Intensity Hold to Change Intensity
OR OR
M M M M
C Cntd.) RGB
Channel 1 (Red) Channel 2 (Green) Channel 3 (Blue)
Display Off
Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity
OR OR OR
M M M M M
C Cntd.) RGBA/W
Channel 1 (Red) Channel 2 (Green) Channel 3 (Blue) Channel 4 (Amber/White)
Display Off
Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity Hold to Change Intensity
OR OR OR OR
M Display Off
LED Groups
Reset to Factory Defaults
M — ++ + RESETPRESS MENU
Reset(Press & hold for 5 sec)
5.1 Program eldoLED® Linear100D to relevant color group to match LED strip (See List).
5.2 Adjust intensity of each channel until the desired color is
reached. Use diagrams on the right to program correlating
color scheme.
*If eldoLED® Linear100D does not function properly, reset to factory defaults.
OPTIC ARTS PRO TIP:If eldoLED® Linear100D continues to malfunction, refer to Reset To Factory Default.
-
11 of 21
213.250.6069
www.opticarts.com
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
5 DMX CONTROLLER.
5.1 Wire eldoLED® Linear100D to DMX Controller (Either Optic Arts® provided or by others). If multiple eldoLED® Linear100Ds are
used, connect in parallel to other eldoLED® Linear100Ds.
5.2 Set mode to DMX.
*If eldoLED® Linear100D does not function properly, reset to factory defaults.
M M
M
SET MODE
Set Mode (Click + or - to change)(5 sec)
Display Off
Display Off
COLRSHOWDMX
Reset to Factory Defaults
DMX Controller Wiring
Set Mode to DMX
M — ++ + RESETPRESS MENU
Reset(Press & hold for 5 sec)
All DMX cabling shall conform to ANSI E1.27-2-2009 (R2014), recommended practice for permanently installed control cables for use with ANSI E1.11 (DMX512-A) and USITT DMX512/1990 products. The maximum total length of a daisy-chain DMX control run is 300 meters (1,000 feet) using the lowest grade cabling
conforming to ANSI E1.27-2-2009 (R2014). Improved wire gauge and shielding can extend this limitation. Some additional devices such as repeaters or splitters may also extend this limitation. Consult manufacturer to validate any limitation extensions. Every DMX control run must be terminated after the last DMX
control module in a daisy-chain sequence with a DMX terminator..
OPTIC ARTS® DMX CONTROLLER OR
BY OTHERS
OPTIC ARTS PRO TIP: Max of 10 modules on one DMX line. Consult DMX Controller datasheet for maximum device limitation specific controller.
DMX Cabling such as Belden 9841 (or similar)*:Blue > DMX+White > DMX–Shield > Common
OPTIC ARTS PRO TIP:If eldoLED® Linear100D continues to malfunction, refer to Reset To Factory Default.
OUT TO NEXT MODULE
DMX in +
LEDSync thru +LEDSync thru -
DMX in -DMX in shield
LEDSync shield
DMX in +
LEDSync thru +LEDSync thru -
DMX in -DMX in shield
LEDSync shield
24V DC-
24V DC+
To F
LEX
To F
LEX
-
12 of 21
213.250.6069
www.opticarts.com
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
5.3 Program eldoLED® Linear100D to relevant color group to match LED strip (See List).
*If eldoLED® Linear100D does not function properly, reset to factory defaults.
M M M M+ LED EXT INP DIM CURV
LED Groups(Click + or - to change)
Single Color
RGBRGBW
Variable White
External Input Dimming Curve
Display Off
1-1L2-2L3-3L4-4L2-4L1-4LRGBRGBWRGBARRGBRGGBCCWWCWWW
OFFPOTM10VSWIT
LOGLIN
LED Groups
5 DMX CONTROLLER.
-
13 of 21
213.250.6069
www.opticarts.com
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
5.4 Set DMX Addresses according to the desired zones of control.
*If eldoLED® Linear100D does not function properly, reset to factory defaults.
M M M MDMX ADDR NETW RES INTERPOL
DMX Address(Click + or - to change)
FLEX RGB ConfigurationDMX Addresses increase by increments of 3 DMX Addresses increase by increments of 4 DMX Addresses increase by increments of 2
FLEX VW ConfigurationFLEX RGBA/W Configuration
External Input Interpol
Display Off
*1...512 8 BT16 BT
OFFVIDCOLRWHITGLOW
Setting DMX Address
M Display Off
Reset to Factory Defaults
M — ++ + RESETPRESS MENU
Reset(Press & hold for 5 sec)
1
4
1
3
DM
X CO
NTR
OLL
ER
BY O
THER
S
1
5
OPT
IC A
RTS®
DM
X
CON
TRO
LLER
OR
BY
OTH
ERS
7 59
5 DMX CONTROLLER.
OPTIC ARTS PRO TIP:If eldoLED® Linear100D continues to malfunction, refer to Reset To Factory Default.
(Repeat step for additional modules) (Repeat step for additional modules) (Repeat step for additional modules)
DM
X CO
NTR
OLL
ER
BY O
THER
S
24V DC-
To F
LEX
To F
LEX
To F
LEX
To F
LEX
To F
LEX
To F
LEX
To F
LEX
To F
LEX
To F
LEX
24V DC- 24V DC- 24V DC-
24V DC- 24V DC-
24V DC- 24V DC- 24V DC-
24V DC+
24V DC+ 24V DC+ 24V DC+
24V DC+ 24V DC+
24V DC+ 24V DC+ 24V DC+
OUT TO NEXT MODULE OUT TO NEXT MODULE OUT TO NEXT MODULE
-
14 of 21
213.250.6069
www.opticarts.com
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
5.5 Remove faceplate from controller by carefully inserting a flathead screwdriver into
slot A and gently pulling up.
A
This step only is applicable if using an Optic Arts® DMX controller (CTRLDMX.4CH.3S.W).5 DMX CONTROLLER.
-
15 of 21
213.250.6069
www.opticarts.com
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
This step only is applicable if using an Optic Arts® DMX controller (CTRLDMX.4CH.3S.W).
5.6 Wire DMX Controller to eldoLED® Linear100D.
24V DC+
24V DC+
24V DC-
24V DC-
GG100E-24-UNV
GG100E-24-UNV
CTRLDMX.4CH.3S.W
CTRLDMX.4CH.3S.W
DMX Controller Power Supply
(LV10-24N-120-A)
CTRLDMX.4CH.3S.W
DMX Cabling such as Belden 9841 (or similar)*:
• Blue > DMX+• White > DMX–• Shield > Common
24V
DC-
24V
DC+
DM
X in
+
DM
X in
-
DM
X in
shi
eld
GG100E-24-UNVor
LV10-24N-120-A
LINEARdrive 100D
5 DMX CONTROLLER.
CTRLDMX.4CH.3S.W
CTRLDMX.4CH.3S.W
GND
GND
D+
D+
D-
D-
V+
V+
V-
V-
OUT TO NEXT MODULE
OUT TO NEXT MODULE
DMX in +
LEDSync thru +LEDSync thru -
DMX in -DMX in shield
LEDSync shield
DMX in +
LEDSync thru +LEDSync thru -
DMX in -DMX in shield
LEDSync shield
24V DC-
24V DC+
To F
LEX
To F
LEX
-
16 of 21
213.250.6069
www.opticarts.com
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
5.7 Make power and DMX connections on the controller body
terminal blocks (See Figure 1). If DMX Controller Power Supply is
used, make connection and place power supply in junction box
before proceeding to next step.
5.8 Mount controller body on Junction Box with screws.
5.9 Align faceplate connector with pins on controller body and snap
faceplate into place.
5.10 Fit controller onto Junction Box.
Note: Power to come from GG100E-24-UNV Driver used to power
fixtures. Controller consumes 5 watts.
Figure 1
Figure 2
DMX Controller Power Suppy
Note: Wire color coding depends on wire type used.
Note: Wire color coding depends on wire type used.
5 DMX CONTROLLER.DMX Controller wired to GG100E-24-UNV Driver DMX Controller wired to DMX Controller Power Supply
Note: Refer to Diagram #2 on Page 2 for wiring instructions.
Note: Refer to Diagram #2 on Page 2 for wiring instructions.
CTRLDMX.4CH.3S.W
CTRLDMX.4CH.3S.W
GND
GND
D+
D+
D-
D-
V+
V+
V-
V-
This step only is applicable if using an Optic Arts® DMX controller (CTRLDMX.4CH.3S.W).
-
17 of 21
213.250.6069
www.opticarts.com
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
5.11 Test each function of DMX Controller to ensure successful installation.
Red Channel• Tap to turn on/off
• Hold to adjust light intensity
WALL MOUNTED DMX CONTROLLERBUTTON FUNCTIONS
Green Channel• Tap to turn on/off• Hold to adjust light intensity
Blue Channel• Tap to turn on/off
• Hold to adjust light intensity
Warm White, Natural White, Cool White• Tap to switch between warm, natural & cool white mixed
with RGB
Hold to adjust overall light intensity
Select color from RGB color wheel
White Channel• Tap to turn on/off• Hold to adjust light intensity
Master on/off
• Play/Pause programmed effects• Hold to adjust effect speed
• Hold to save color/effects preset• Tap to recall preset
5 DMX CONTROLLER. This step only is applicable if using an Optic Arts® DMX controller (CTRLDMX.4CH.3S.W).
-
18 of 21
213.250.6069
www.opticarts.com
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
TROUBLESHOOTING DMX CONTROLLER
A. If controller is unresponsive, push to turn off controller (red LED will light on Controller), then push to turn on (blue LED will light on controller) & retest controller functionality. If light fixture does not turn on, move on to next step.
B. Turn on controller and hold down to test and see if light fixture ramps up or down. Repeat, hold down button 2-3 times. If FLEX LED does not turn on, move on to next step.
C. Turn on controller and tap each of the following color buttons _________ or _________ or _________ or _________, If FLEX LED does not turn on, then hold down color wheel buttons to test if LED brightens/dims. Repeat 2-3 times for each. If FLEX LED does not turn
on, move on to next step.
D. Turn on controller and scroll through center color wheel. If FLEX LED does not turn on, move on to next step.
E. Set groups on LinearDrive100D (See Step 4.2, page 4) to COLOR, then SHOW, then back to DMX. Repeat steps from Troubleshooting Step A. If FLEX LED does not turn on, move on to next step.
F. Check wiring (See Step 4, page 4), then check every setting following to match corresponding FLEX LED. Repeat steps from Troubleshoot Step A. If FLEX LED does not turn on, move on to next step.
G. Reset eldoLED® Linear100D to factory settings and start from Step 4 (see page 4). Repeat Troubleshooting DMX Controller.
Follow step by step until issue is resolved.
5 DMX CONTROLLER.Page must be printed in color.
-
19 of 21
213.250.6069
www.opticarts.com
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
6.
6.1 Reinstall strain relief pieces.
6.2 Reinstall faceplate cover.
6.3 Cover UL Listed Enclosure (by others).
eldoLED® Linear100D
To FLEXTo GG100E-24-UNV
-
20 of 21
213.250.6069
www.opticarts.com
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
Problem Solved!
Tap M button on eldoLED® Linear100D. Does the eldoLED®
Linear100D display turn on?
Do all eldoLED® Linear 100D(s) fail to turn on?
Do all FLEX colors match the corresponding control channel?
Check wiring and retest each channel. Does error persist?
Contact Optic Arts at 213.250.6069
Program eldoLED® Linear100D to relevant Color Group
to ensure FLEX color coordinates with control
channel to match LED setup. (Reference TROUBLESHOOTING
MALFUNCTIONING FLEX PRODUCT STEP B & C for further
instruction). Do all FLEX channels turn on?
Wire each channel of FLEX product directly into ELECTRONIC DRIVER.
Do all FLEX channels turn on?
Wire another FLEX lunimnaire to the same driver. If FLEX does not
turn on, re-test with all other FLEX. Are all FLEX not turning on?
Wire same product to another driver. If product does not work, retest with all other drivers. Are
all drivers not turning on product?
Check input power line. Are all drivers working?
No
No
No
Yes
Yes
Wire another eldoLED® Linear 100D to same driver. If eldoLED® Linear 100D does not turn on, re-
test with all other eldoLED® Linear 100D. Are all eldoLED® Linear
100D(s) functioning?
No
Yes
No
No
Yes
No
Yes
No
Yes
YesNo
Yes
Yes
Yes
START HERE
No
DRIVER/eldoLED® LINEAR100D/FLEX LED TROUBLESHOOTING
-
21 of 21
213.250.6069
www.opticarts.com
Optic Arts reserves the right to modify this specification without prior notice. Last Modified: January 29, 2018
© Optic Arts 2018; 1130 Monterey Pass Rd, Monterey Park, CA 91754
DMX SYSTEM INSTALLATION GUIDE
Problem Solved!
Is the DMX controller responsive?
Tap power button to switch DMX controller on. (Red LED on DMX
controller means on) (Blue LED on DMX controller means off) Does the LED on the DMX controller
light up?
Turn on DMX controller & hold down (sun icon) to test if light
fixture ramps up & down. Repeat hold down 2-3 times. Do any of
the luminaires ramp up?
Check wiring connection of DMX controller. Does the LED on the DMX controller light up after
fixing connection?
Check wiring of every channel that is non-responsive. Are all channels on FLEX responsive to the functions on the DMX
controller?
(See pg. 18) Step D > Do any of the luminaires turn on?
(See pg. 18) Step E > Do any of the luminaires turn on?
(See pg. 18) Step F > Do any of the luminaires turn on?
(See pg. 18) Step G > Do any of the luminaires turn on?
Are all channels on FLEX responsive to the functions on
the DMX controller?
Are all DMX controller features functioning properly?
Are any luminaires responsive to the DMX controller?
Test functions on DMX controller. Are all DMX controller features
functioning properly?
Do any of the luminaires turn on?
Contact Optic Arts at 213.250.6069
START HEREDMX CONTROLLER TROUBLESHOOTING
YesYes
Yes
Yes
Yes
Yes
YesNo
No
No
No
No
No
No
No
No
No
No
No
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes