220VAC Swing Gate Operator

USER’S GUIDECONTROLLER

PKM1.2K

2

21)Ensure that entrapment between the driven part and the surrounding fixed parts due to the opening movement of the driven part is avoided.

22)After installation, ensure that the mechanism is properly adjusted and that the protection system and any manual release function correctly.

23)Permanently fix the label concerning the manual release adjacent to its actuating member.

24)The drive cannot be used with a driven part incorporating a wicket door.

~220V(10%)50HZ

~220V/24V/12V/10W

200mA(AC24V)

-10 C~450 C

5AX2

60S

Power supply

Transformer

Accessories max loaded

Environment temperature

Protection fuse

Running time protect(Max)

Auto close time delay Programmable(0~99)

Force

E_LOCK Relay out

Adjustable

Transformer

BUZZER Fuse (5A)

Fuse(5A)

Force of motor 2adjust

Auto-close time adjust

Dipswitch

Terminal (power and motor)

Fuse(0.2A)

3.Controller:

4.1 Button instruction:

S1:Open the gate and increase 1 every once push when adjust the interval time between left and right leaf. S2:Close the gate and decrease 1 every once push when adjust the interval time between left and right leaf. S4:Stop the gate when the gate is running. Set the interval time between left and right leaf when the gate is stopped.

3

2. Example of a sliding gate operator installed:

Alarm light

Controller

po

wer

cab

le

Operater 1

Operater 2

Force of motor 1adjust

receiver board

Learnbutton

main icbutton

Terminal (limit and photocell...)

Auto-close function is invalid

Auto-close function is available

Cancel E-lock function

E-lock not work

Force test

Cancel force test function

4.2 Dip-switch(S3)setting:

Adjust the force of Motor1

Clockwise is more , Auticlockwise is less

Adjust the force of Motor2

Clockwise is more , Auticlockwise is less

Force of Motor:

ADD DEC

ADD DEC

POWER MOTOR1 MOTOR2 LIGHTAC220V AC24V

POWER-OUT

AC-NAC-L L1-1 COM L1-2 L2-1 COM L2-2

5.Connection of Motor:

220V/AC INPUT

ALARM LIGHT (220VAC)

24V/AC OUTPUT

LIMIT1 LIMIT2 PHOTOCELL BUTTON LOCKOL COM CL OL COM CL GND PHOTO V+ CLOSEOPEN COMPUSH RELAY-OUT

AC24V

NC

CO

M

E-LOCKRELAY-OUT

MOTOT1(220V/AC)

LIMIT2

MOTOR2(220V/AC)

* If the gate is only 1 leaf, the motor must be connected with MOTOR1" and LIMIT1"." "*If the gate is 2 leaves, first, it must be confirmed witch one leaf is the priority opening one. The priority opening leaf must be connected with "MOTOR1", the other one is connected with "MOTOR2"

5

LIMIT1

PHOTOCELL

OPEN

CLOSE

PUSHPhotocell input-must be bridged if not used

emitter receiver

LIMIT STOPPER

LIMIT SWITCH

“be,be”Y

N NThe time decrease and the beep “be”

“be,be”Y

EndSpot press”S4" button

POWER ON

Spot press”S4" button

“Be”,“Be”LED1 flashing

spot press“S2"button

The time isless than 0s?

The time increase and the beep “be”

spot press“S1"button

The time ismore than 9s?

Set delay time between 2 motors operating:

7

*No power*Break fuse

*Check power supply*Change fuse*Connect the limit*Not connect limit

*Change the motor

*The interval time between left and right leaf is very long

*Decrease the interval time

*Connectthe motor cable or

limit switch.

Motor not working

Only one motor working

*Motor is damaged

*The motor (or limit switch)not connect with control board .

First, press "LEARN BUTTON" once , the "LEARN LED" light, then,

press the button you choose on transmitter till the "LEARN LED "

flash and go out ,This button control double- leaf.

Second , press "LEARN BUTTON" twice, the "LEARN LED" light, then,

press ano ther button you choose on transmitter till the "LEARN LED "

flash and go out, This button control leaf open.

Now , the transmitter is coded, Other transmitters can be coded as this way.

Press"LEARN BUTTON" and hold on to make the "LEARN LED" light till go out .Now ,all codes of transmitters which had been learnt are cleared.

8.2: Earsuring transmitter codes:

8.1: Setting transmitter code:LEARN BUTTONLEARN LED

9.Trouble Shooting:

*Clutch is released* Use the key to couple the clutch

*Operating handle is broken

*Worm gears are jammed*Change the handle

*Rotate the pinion

*Position of limit switch is not correct

*Limit switch is damaged

*Adjust position

*Change limit switch

*Distance of limit switch is too large*Limit switch is wrong*Magnetic- steel’s position is wrong

*Adjust position of limit switch*Change limit switch*Re-adjust the position