26ld320h 32ld320h 37ld320h 42ld320h …€¦ · master tv setup pages 11 – 14 cloning information...

Master TV Setuppages 11 – 14

Cloning Informationpages 23 – 29

FTG Mode of Operationpages 30 – 40

EXPERIENCED INSTALLER

Commercial Mode Setup Guide Note: Selected features shown in this guide may not be available on all models.

Lodging Guest Interactive Pro:Centric™ TVs

© Copyright 2011, LG Electronics U.S.A., Inc. P/N: 206-4186 (Rev B)

26LD320H 32LD320H 37LD320H 42LD320H 32LD325H 37LD325H

26LD340H 32LD340H 37LD340H 42LD340H 26LD345H 32LD345H 37LD345H 42LD345H

2 206-4186

MODEL and SERIAL NUMBERThe model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here: Model No._________________ Serial No._______________

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:This product is equipped with a 3-wire grounding-type alternating current power plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the 3-wire grounding-type plug.

NOTE TO CABLE/TV INSTALLER: This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equip-ment does cause harmful interference to radio or television reception, which can be determined by turning the equip-ment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver. • Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.

CAUTION: Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE: The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA • Phone: 1-201-816-2000

WARNINGRISK OF ELECTRIC SHOCK

DO NOT OPEN

© Copyright 2011, LG Electronics U.S.A., Inc.

For Customer Support/Service, please call: 1-888-865-3026

The latest product information and documentation is available online at: www.LGsolutions.com/products

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc.1000 Sylvan Avenue, Englewood Cliffs, NJ 07632

3206-4186

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accor-

dance with the manufacturer’s instructions.8. Do not install near any heat sources, such as radiators,

heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the appara-tus. When a cart is used, use caution when moving the cart/apparatus combination in order to avoid injury from tip-over.

13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been dam-aged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

14. Never touch this apparatus or antenna during a thunder or lighting storm.

15. When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.

16. Do not allow an impact shock or any objects to fall into the product, and do not drop objects onto the screen.

17. Power Cord Caution: It is recommended that appliances be placed

upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page in the Owner’s Manual to be certain.

Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as twisting, kinking, or pinching or being closed in a door or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

Do not use a damaged or loose power cord. Be sure to grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

18. Overloading Do not connect too many appliances to the same AC power

outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or dam-aged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in fire or electric shock.

19. Outdoor Use/Wet Location Warning: To reduce the risk of fire or electrical shock, do not expose this product to rain, moisture or other liquids.

Do not touch the TV with wet hands. Do not install this prod-uct near flammable objects such as gasoline or candles or expose the TV to direct air conditioning.

Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc., on or over the apparatus (e.g., on shelves above the unit).

20. Grounding Ensure that you connect the earth ground wire to prevent

possible electric shock (i.e., a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a quali-fied electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightning rods, or gas pipes.

21. Disconnect Device The mains plug is the disconnecting device. The plug must

remain readily operable.

As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH.

(Continued on next page)

PORTABLE CART WARNING

4 206-4186

IMPORTANT SAFETY INSTRUCTIONS

(Continued from previous page)

22. Outdoor Antenna Grounding If an outside antenna or cable system is connected to the

product, follow the precautions below.

An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.

Article 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Antenna Grounding According to NEC, ANSI/NFPA 70

23. Cleaning When cleaning, unplug the power cord and wipe gently with

a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.

24. Transporting Product Make sure the TV is turned Off and unplugged and that all

cables have been removed. It may take two or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV during transport.

25. Ventilation Install the TV where there is proper ventilation. Do not install

in a confined space such as a bookcase. Do not cover the TV with cloth or other materials (e.g., plastic) while it is plugged in. Do not install in excessively dusty places.

26. Do not touch the ventilation openings, as they may become hot while the TV is operating.

27. If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord, and contact an authorized service center.

28. Do not press against the front panel of the TV with your hand or a sharp object (e.g., a nail, pencil, or pen) or make a scratch on it.

29. Keep the product away from direct sunlight.

30. Dot DefectThe LCD panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see fine dots on the screen while you are viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.

31. Generated Sound“Cracking”: A cracking noise that occurs while the TV is On or when it is turned Off is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. This generated sound does not affect the performance and reliability of the product.

32. For LCD TVIf the TV feels cold to the touch, there may be a small “flicker” when it is turned On. This is normal; there is nothing wrong with TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.

Antenna Lead in Wire

Antenna Discharge Unit(NEC Section 810-20)

Grounding Conductor(NEC Section 810-21)

Ground Clamps

Power Service GroundingElectrode System (NECArt 250, Part H)

Ground Clamp

Electric ServiceEquipment

5206-4186

Table of Contents

Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2Important Safety Instructions . . . . . . . . . . . . . . . . . . . .3 – 4Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Commercial Mode Overview. . . . . . . . . . . . . . . . . . . . .6 – 7

Setup Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6Pass-through Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . 6FTG Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Remote Management in FTG Mode . . . . . . . . . . . . . . . 7External MPI Control . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Pro:Centric Operation. . . . . . . . . . . . . . . . . . . . . . . . . .8 – 9Pro:Centric TV Interactive Menu Features . . . . . . . . . . 8Pro:Centric Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installer Remote Control Typical Key Functions . . . . . 10Master TV Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .11 – 14

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Cloning Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Clonable TV Setup Menu Features. . . . . . . . . . . . . . . 11Master TV Setup Procedure . . . . . . . . . . . . . . . . . . . . 12

Installer Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 – 21Accessing the Installer Menu . . . . . . . . . . . . . . . . . . . 15Using the Installer Menu . . . . . . . . . . . . . . . . . . . . . . . 15Exiting the Installer Menu and Activating Updates . . . 15

Channel Icons / Custom Text Labels (2-5-4 + MENU Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . 22Cloning Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23USB Cloning Procedure. . . . . . . . . . . . . . . . . . . . .24 – 25

Learning / Teaching a Master TV Setup using a USB Memory Device . . . . . . . . . . . . . . . . . . . . . . 24

Clone Programmer Cloning Procedures . . . . . . .26 – 29Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer . . . . . . . . . . . . . . . . 26Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer . . . . . . . . . . . . . . . . . . 28

FTG Mode of Operation Overview . . . . . . . . . . . .30 – 31FTG Mode via CPU or EBL. . . . . . . . . . . . . . . . . . . . . 30Determining the TV Operating Mode . . . . . . . . . . . . . 31

FTG Mode via CPU . . . . . . . . . . . . . . . . . . . . . . . . .32 – 35Creating an FMA Configuration File using the FTG Device Configuration Application . . . . . . . . . . . . . . . . 32Teaching FMA Configuration to a TV . . . . . . . . . . . . . 33Learning an FMA Configuration File from a TV . . . . . 34Optional Manual Configuration / TV Setup . . . . . . . . . 35

FTG Mode via EBL . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36FTG Device Configuration Application Utilities Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 – 40

FTG Channel Map Configuration Utility . . . . . . . . . . . 37FTG Channel Map Editor . . . . . . . . . . . . . . . . . . . . . . 38FTG Installer Menu Configuration Utility. . . . . . . . . . . 39FMA Configuration Utility . . . . . . . . . . . . . . . . . . . . . . 40

Remote Jack Pack / TV Connections & Setup . . . . . . . 41

ReferencesUpgrading TV/PTC Software using a USB Memory Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42Downloading a Splash Screen using a USB Memory Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 Power Consumption Settings. . . . . . . . . . . . . . . . . .44 – 45TV Camport Auto Sense Operation . . . . . . . . . . . . . . . . 46TV Aux Input Configuration . . . . . . . . . . . . . . . . . . . . . . 47b-LAN Setup & Overview . . . . . . . . . . . . . . . . . . . . . . . . 48RJP Model List and Input Auto-sensing Hierarchy. . . . . 49Resetting Factory Defaults on the TV(s) . . . . . . . . . . . . 50LD320H/LD325H & LD340H/LD345H Rear Jack Panel . 51Side Connections Panel / RF Antenna & MPI Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 – 56General Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . 53Troubleshooting Flow Chart . . . . . . . . . . . . . . . . . . . . 54Commercial Mode Check / FTG Operating Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55Clone Programmer Troubleshooting . . . . . . . . . . . . . . 56

Glossary of Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Document Revision History / Notes . . . . . . . . . . . . . . . . 58Back Cover. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Notes • Installer Menu content is intended for use primarily by qualified TV electronics technicians. • Refer to the Owner’s Manual for additional information on TV installation, features, specifications, maintenance, and safety

instructions.• Design and specifications subject to change without prior notice.

6 206-4186

Installation and Setup Checklist__ Unpack TV and all accessories.__ Install batteries in remote control.__ Install TV on VESA mount or stand. Note: It may be advisable to make all cable

connections before installing on VESA mount or stand, as appropriate.

Hardware Connections__ Install any additional hardware as

appropriate to your institution, LAN, etc.

Cable Connections__ Make all rear jack panel and MPI card slot

connections, as appropriate.

Commercial Mode Setup__ Complete appropriate procedures as described

in this document for Commercial Mode operation. See “Pass-through Mode” and “FTG Mode” sections below for further information.

Commercial Mode Overview

This document describes how to set up LD320H/LD325H and LD340H/LD345H Pro:Centric™ TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’s CPU, Protocol Translator Card (PTC), or embedded b-LAN™ (EBL) module, or it resides externally from the TV (i.e., in a device from the solution provider). Each of these TV models has an EBL module that can be configured either for Pass-through Mode (default) or Free-To-Guest (FTG) Mode. In addition, each of these TVs is capable of FTG Mode operation via the TV CPU when the EBL is in Pass-through Mode.

Setup ChecklistNote: This document provides information specific to Commercial Mode operation. Refer to the Owner’s Manual for detailed information on TV installation and hardware and cable connections.

Typical Installer Menu

Installer MenuTo set up a Master TV for cloning purposes, you will need to know how to enter the commercial controller (PTC) Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the Installer Menu and how to make and save changes. Refer to pages 15 to 21 for information on accessing the Installer Menu in Pass-through Mode and for detailed descriptions of the Installer Menu items.

TV Setup MenusOn-screen setup menus control the features of the TV. Use the Installer Remote to access the TV setup menus, and set the TV features to the desired configuration for the end user. Refer to the Owner’s Manual for detailed information on the TV setup menus.

Pass-through Mode This mode allows you to create a Master TV Setup for cloning purposes for TVs that are to remain in Pass-through Mode. This mode also allows external control via the TV’s GAME CONTROL/MPI port. Use the Installer Remote to configure Installer Menu items as required for TV operation and set up TV features (Channel, Picture, Audio, etc.). See “Master TV Setup” on pages 11 to 14 for detailed information.

TV Setup Menus

PICTURE AUDIO

INPUTOPTION

TIME

MY MEDIA

CHANNEL

LOCK

xxLD340H PTC INSTALLER MENU

000 INSTALLER SEQ 000

UPN 000-000-000-000 ASIC 20E7 PTC V1.00.001 CPU V3.25.00

7206-4186

Commercial Mode Overview (Cont.)

CloningCloning refers to the process of capturing a Master TV Setup and transferring it to a Target TV (both TVs must be in Pass-through Mode). The Master TV’s clonable setup menu options should be configured as part of the Master TV Setup. If there are features in the Master TV’s setup—channel icons or labels, digital font options, etc.—that are not set or that are set incorrectly, those features also will not be set or will be set incorrectly in the Target TVs. Pages 23 to 29 provide detailed information on cloning requirements and procedures.

FTG ModeThis mode enables Pro:Idiom ® decryption and also allows logical channel mapping of physical channels to remove the need for dash tuning. TV operation in FTG Mode is based on which element of the TV owns the FTG Logical Channel Map—the CPU or the EBL. Understanding the application in which the TV will be used is vital in determining the owner. As indicated above, FTG mode operation in the LD320H/LD325H and LD340H/LD345H models can be provided either by the TV CPU or EBL (see note below). These are two separate and distinct FTG Modes of operation, each with its own unique advantages and requirements as described later in this document. When the TV CPU is configured with an FTG Channel Map, the CPU controls the operation of the TV, and when the EBL is configured with an FTG Channel Map, the EBL controls the operation of the TV.Once it is determined whether the TV CPU or the EBL will own the FTG Channel Map, configuration can begin. Configuration of either requires the LG FTG Device Configuration Application. This application pro-vides utilities that enable you to create/edit an FTG Channel Map and configure Installer Menu settings. See pages 30 to 40 for further information on FTG Mode operation and configuration. Note: LD320H/LD325H TVs must have the following minimum software loads in order to support FTG Mode via CPU: CPU version 3.61 or later and PTC version 1.01.008 or later. If necessary, contact LG to obtain LD320H/LD325H CPU and PTC software files, and perform the software updates as described in Reference section, “Upgrading TV/PTC Software using a USB Memory Device.”

Remote Management in FTG ModeWhen the TV is configured for FTG Mode via CPU, remote management of the FTG Channel Map and FTG Installer Menu settings is provided by a Pro:Centric server. Refer to the Pro:Centric™ Server Admin Client User Guide for further information.When the TV is configured for FTG Mode via EBL, the b-LAN module, which is internal to the TV, allows hotel/institution head end equipment (for example, an FMA-LG101) with b-LAN technology to communi-cate with the TV to provide remote management of the FTG Channel Map and FTG Installer Menu set-tings. See Reference section, “b-LAN Setup & Overview,” for further information.

External MPI ControlTo control the TV using an external MPI control device, you must use the TV’s GAME CONTROL/MPI port for communication purposes. In these TVs, Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port; therefore, to ensure that the GAME CONTROL/MPI port circuitry is powered, thus enabling MPI communication, Installer Menu item 118 POWER SAVINGS must be set appropriately. See Installer Menu item descriptions as well as reference section, “b-LAN Setup & Overview,” for further information.

8 206-4186

Pro:Centric TV Interactive Menu Features

Important: Pro:Centric operation requires that Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL be set appropriately and that the TV be in PPV or FTG Mode.

The interactive Pro:Centric TV enables guests—from the comfort of their hotel rooms—to view and select from a complete listing of hotel services and amenities. The Pro:Centric TV is connected to the hotel's billing computer, and service/amenities charges are billed at the time of order.Interactive amenities may include:• Hotel information, news, and events• Directory services (tourist attractions, restaurants, etc.)• Reservation services (business meetings, fitness, spa, etc.)• Weather and traffic information• Shopping services (delivery to guest room)• Room service (menu ordering, memo service, morning wake up call, laundry, etc.)• Ticketing and gaming services• Check-out service (in the guest room)• E-mail resources/account access

Use the Installer Remote to operate both interactive menus and regular TV features. Press PORTAL on the Installer Remote to access the interactive menus.Note: Interactive menu options may vary, depending on Pro:Centric features enabled for the site. The following are default interactive menus.

Channel GuideShows available TV networks and logical channels. When available, electronic program guide (EPG) data provides additional channel and program information.

InformationTypically displays hotel information, for example, photos of guest rooms, dining rooms, business centers, facilities, etc., as well as information on local weather and attractions. Information may also include resources, such as local school programs, run in coopera-tion with the hotel.

HelpProvides help for navigating the interactive menus.

Watch TVRemoves the interactive menu from the screen and returns to the previously tuned TV channel.

MENU

MUTE

VOL CHPAGE

RETURN

INPUT

TV

ALARM TIMER

1 2 34 5 67 8

09

FLASHBK

PORTAL

ENTER

GUIDE

EXIT

INFO

EJECT

SAP

RATIO

CC

i

Pro:Centric Operation

9206-4186

Pro:Centric Operation (Cont.)

Pro:Centric SetupThe Pro:Centric server provides the following functionality:• Remote management/administration (TV E-Z Installation): The Pro:Centric server Admin Client provides

remote management/administration facilities for downloading splash screens and software/firmware updates as well as facilities for downloading FTG Channel Map and FTG Installer Menu settings for TVs that are in FTG Mode via CPU (see also “Remote Management in FTG Mode” on page 7). The Data Channel must be set appropriately in the Installer Menu (item 119 DATA CHANNEL) to enable Pro:Centric remote management/administration facilities.

• Pro:Centric application: The application comprises the Pro:Centric interactive menus/features described on the previous page. Pro:Centric application settings are managed via the Pro:Centric server Admin Client. In addition to the Data Channel, the Pro:Centric Application Mode must be set appropriately in the Installer Menu (item 098 PRO:CENTRIC) to enable the Pro:Centric application.

Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric™ Server Admin Client User Guide. This document describes only those settings that must be specified on the TVs.

10 206-4186

Installer Remote Control Typical Key Functions

MENU

MUTE

VOL CHPAGE

RETURN

INPUT

TV

ALARM TIMER

1 2 34 5 67 8

09

FLASHBK

PORTAL

ENTER

GUIDE

EXIT

INFO

EJECT

SAP

RATIO

CC

i

NUMBER Buttons (0 - 9) & DASH Use to enter a program number or channel. Dash is used for sub-channel numbers such as 2-1, 2-2, 9-1, 9-2, 100-3, 100-4, etc.

FLASHBK (FLASHBACK) Returns to the previously tuned channel.

The LG Installer Remote is supplied with and dedicated to operate the TV. The LG Installer Remote illustrated below and throughout this document shows typical remote control functions and is provided for reference only. This Installer Remote may vary from the Installer Remote supplied with the TV.

Color buttons access special functions in some menus.

USB BUTTONS Use to view/navigate USB memory

device content.

EJECT Ejects a USB memory device.

VOLUME UP/DOWN Increases/decreases sound level.

INFO Displays channel information.

PORTAL Displays and removes the interactive

menu.

MUTESwitches sound ON or OFF.

CHANNEL/PAGE UP/DOWN Changes the channel. Moves from

one full set of screen information to the next.

Arrows (Up/Down/Left/Right) & ENTERUse to navigate on-screen menus and adjust TV settings to your requirements.

MENU Displays the TV setup menus on the screen. Also exits the on-screen menu system and returns to TV viewing.

GUIDE Displays and removes the electronic program guide.

CC Press to activate subtitles.

RETURN Returns one level to the previous menu/ display.

SAP Analog Mode: Selects MTS sound (Mono, Stereo, or SAP). DTV Mode: Changes audio language, if additional languages are available. *

EXIT Clears all on-screen displays and returns to TV viewing.

POWER Turns TV ON or OFF.

ALARM Sets the time when the TV

will automatically turn itself ON.

TIMER Sets the amount of time before the TV

automatically turns itself OFF.

INPUT Selects RGB, HDMI/DVI1, HDMI2,

Component Input, AV1, and AV2 sources.

TV Returns to the last TV channel

(from an Aux input).

SAP notes:• If SAP is selected and no SAP is provided, sound

may not be heard on channel. • Each analog channel may have its own SAP setting. • Digital channels will reset to default audio language

with a power off/on.

*

RATIO Adjusts the picture aspect ratio.

11206-4186

Master TV Setup

This section describes how to set up a Master TV for cloning purposes when the TV is in Pass-through Mode.Note: Refer to FTG Mode information on pages 30 to 40 for details on entering FTG Mode and configuring/editing FTG Channel Map and FTG Installer Menu settings.

Before You Begin• Disconnect all Aux inputs if you intend to run Auto Tuning (Channel Search). Under certain conditions,

Auto Tuning is disabled if there is an Aux input active.• Determine which cloning tool—USB memory device or clone programmer—is appropriate for your

application. See “Cloning Methods” below for further information.

Cloning MethodsUsing a USB Memory Device / .tll FileThe .tll file format clones the contents of the commercial controller (PTC) memory, including an auto-tuned/edited Channel Map, Installer Menu settings, and one TV source’s (analog, digital, or Aux) clonable setup menu settings. See “Clonable TV Setup Menu Features” list below.

Using a Clone Programmer (TLL-1100A or LT2002)Both the TLL-1100A and LT2002 clone the contents of the commercial controller (PTC) memory, including an auto-tuned/edited Channel Map, Installer Menu settings, and one TV source’s (analog or Aux) clonable setup menu settings. See “Clonable TV Setup Menu Features” list below.

Clonable TV Setup Menu Features

Channel Auto Tuning (Channel Lineup) Manual Tuning Channel Edit Channel Label

Picture Aspect Ratio Picture Mode

Audio Auto Volume Clear Voice Sound Mode Balance TV Speaker

Time Auto Clock Auto Off (Sleep Timer)

Option Menu Language

Audio Language Caption

Lock Movie Rating TV Rating – Children TV Rating – General

Note: Some menu options vary between analog and digital channels and Aux inputs.

12 206-4186

Master TV Setup (Cont.)


Note: The Installer Menu header will vary depending on the TV you are setting up.

Adjust the settings for these Installer Menu items.


Use the TV setup menus to set the TV features to the desired configuration

for the end user.

PICTURE AUDIO

INPUTOPTION

TIME

MY MEDIA

CHANNEL

LOCK




117 FACT DEFAULT 001

003 BAND/AFC 00X

Master TV Setup Procedure1. Set Installer Menu items.

This step provides specific instruction only on the Installer Menu items that should be set on a Master TV. Refer to pages 15 to 21 for detailed information on all Installer Menu items.

a) Make sure the TV is ON. Then, use the Installer Remote to enter the PTC Installer Menu: Press MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6 + ENTER.

b) Set Installer Menu item 117 FACT DEFAULT to 001 and press ENTER on the Installer Remote. This clears all Installer Menu custom settings, channel lineup, etc. and reloads the factory default settings. The value will change back to 0 after the PTC has been restored to factory default condition. This step ensures that the TV Channel Memory will be the active channel lineup.

c) Set Installer Menu item 003 BAND/AFC, as appropriate.• Broadcast: Set to 000. • HRC: Set to 002.• CATV: Set to 001 (default). • IRC: Set to 003.

d) Set any other Installer Menu items that affect your TV pro-gramming network to the required configuration. For example, enable/disable Aux inputs, set a Start Channel, etc.

e) After you have adjusted all required Installer Menu item settings, press ENTER once on the Installer Remote to save your changes; then, press ENTER again to exit the menu.

2. Set up TV features. On-screen setup menus control the features of the TV. Press MENU on the Installer Remote to access the TV setup menus, and then set Channel, Picture, Audio, Lock, Time, etc. options to the desired configurations. See also the Clonable TV Setup Menu Features list on page 11.Note: Remember that only one TV source’s clonable setup menu settings will be cloned. Thus, for a clone programmer, the TV setup menu settings should be applicable to either an analog channel or Aux input, while for a USB memory device, the TV setup menu settings should be applicable to the analog or digital channel or Aux input to which the Target TV will be set during the Teaching process. Note: If desired, you can run Auto Tuning (see step 3) prior to completing this step.

13206-4186


CHANNEL EnterMove


3. Run Auto Tuning.

a) To search for all available analog and digital channels, go to the Channel Menu, select the Auto Tuning option, and follow the on-screen instructions.

b) Use the Channel Edit option in the Channel Menu to edit the channel lineup, as necessary, to include only free to guest (non-encrypted) channels. • Add/delete channels per your system requirements. • Use the Channel Label option in the Channel Menu to select

the appropriate trademark/icon for each channel’s Channel-Time on-screen display. Icons are available for familiar channels, such as ABC, CBS, NBC, etc. Identifiable labels (icons) should enable the end user to readily know what common networks are available.

Use Channel Menu options to run Auto Tuning, edit channels,

and select channel icons.

Auto TuningManual TuningChannel EditChannel Label


Note: If Installer Menu item 103 ATSC TUNE MODE is set for Physical Channel tuning (default and recommended setting), channels with minor channel numbers higher than 255 will not transfer correctly in step 5. If item 103 is set for Virtual Channel tuning and either the major or minor channel numbers are higher than 255, the channel(s) will not transfer correctly in step 4.Note: You can add the channel icons in this step or as described in step 6. Also in step 6, you can add custom text labels for channels without icons.

4. Transfer the TV setup menu settings to the commercial controller (PTC): 2-5-5 + MENU Mode

Important: This step is essential for successful cloning. Without this step, the PTC will not contain any of the TV setup menu settings.

a) After the TV channel lineup has been edited and channel label icons added, tune to the channel (source) for which you wish to transfer TV setup menu settings. Note: If you intend to use a clone programmer for cloning purposes, this must be either an analog channel or Aux input.

b) Enter the Installer Menu, and press 2-5-5 + MENU on the Installer Remote to initiate the transfer of the Master TV Setup to the PTC. The TV exits the Installer Menu and then tunes through the channels in the channel lineup during the transfer. When the transfer is complete, the TV tunes back to the channel that was tuned before the transfer began.

Note: The maximum number of channels that can be transferred is 141. An attempt to transfer more than 141 channels will result in erratic TV tuning operation.

14 206-4186


5. (Optional) Add Custom Channel and Aux Input Labels: 2-5-4 + MENU Mode

Note: 2-5-4 + MENU Mode enables you to add/edit channel icons and custom text labels in the PTC once the Master TV Setup has been transferred as described in the previous step.Enter the Installer Menu, and press 2-5-4 + MENU on the Installer Remote. Add/edit custom text labels and/or change icons for the Channel-Time on-screen displays (see 2-5-4 + MENU procedural information on page 22). Note that broadcast digital channels often already have a broadcaster generated label. When you are finished, press MENU to exit 2-5-4 + MENU Mode.

6. Verify the TV setup. Verify that the channel lineup, channel icons, and custom text labels are

correct. Also, make sure the TV features are set per your requirements. 7. Lock the channel lineup.

Enter the Installer Menu. Set item 028 CH. OVERIDE to 000 and press ENTER to lock the channel lineup and restrict access to the TV setup menus. Press ENTER again to save your changes and exit the Installer Menu.*

The Master TV Setup is now ready to be copied to the predetermined cloning tool—a USB memory device or a clone programmer. See cloning procedures in this document.

After verifying the TV Setup, set Installer Menu item 028 CH. OVERIDE to 000.*

DIGITAL 19-3

WXYZ

MONO STEREO SAP

Custom text label “WXYZ” created in 2-5-4 + MENU Mode.

* This step prevents end users from accessing channel settings (i.e., the Channel Menu will be inaccessible/grayed out).

028 CH. OVERIDE 000


15206-4186

Installer Menu


Use the Installer Menu to set up or change operational settings.Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing.




Accessing the Installer Menu1. Make sure the TV is ON. 2. Using an Installer Remote, press MENU repeatedly until the on-

screen display of the TV setup menus (if the TV is in Pass-through Mode) or the Function Menu (if the TV is not in Pass-through Mode) no longer toggles, and then press 9-8-7-6 + ENTER to access the Installer Menu.

The Installer Menu opens with item 000 INSTALLER SEQ 000. Note: If the password is not entered or registered correctly, you will see the message “ENTER PASSWORD 0000” at the top of the screen instead of the Installer Menu header. Once you re-enter the correct password (i.e., press 9-8-7-6 + ENTER), the Installer Menu will display.Note: If the TV is in FTG Mode, the Installer Menu is accessible as read-only. Refer to pages 30 to 40 for information on FTG Mode configuration.

Using the Installer MenuRefer to the table on pages 16 and 17 for an overview of the available Installer Menu items, including their item numbers, functions, value ranges, and default values. Installer Menu items not relevant to this TV series are not present in the Installer Menu; therefore, some numbers are missing. For example, item 006 will not appear.

Navigation within the Installer MenuUse the Up/Down arrow keys on the Installer Remote to sequence through the available menu items, or access an item directly by keying in the line number and then pressing MENU. For example, to access the SLEEP TIMER option, which is item 015, press 0-1-5 + MENU.

Changing Installer Menu SettingsTo change an Installer Menu item value, use the Left/Right arrow keys on the Installer Remote, or enter a valid value directly. To save the new setting, press ENTER, or use the Up/Down arrow keys to navigate to a new Installer Menu item if you have additional items to edit. Note that invalid values will not be saved.

Exiting the Installer Menu and Activating UpdatesAfter you have adjusted all required Installer Menu item settings, press ENTER once on the Installer Remote to save your changes; then, press ENTER again to exit the Installer Menu. Any changes you make will be stored in non-volatile memory. Note: Each time you exit the Installer Menu in Pass-through Mode, all V-Chip (Parental Control) settings in the TV are reset to their default values; that is, the Lock System, if previously enabled from the Lock setup menu (see the Owner’s Manual for additional information), will now be disabled, and the individual Parental Control settings will be restored to default values.

16 206-4186

Installer Menu (Cont.)

Installer Menu Items 000 through 071

Menu Item Function Value Range Default Value Brief Description of Function and Comments

000 INSTALLER SEQ 0 ~ 3 0 Leave default set to 0.

001 POWER MANAGE 0 ~ 7 0 Sets number of hours of no activity before automatic shutoff.

002 AC ON 0 / 1 0 Set to 1 to enable Auto Turn ON when AC power is applied.

003 BAND/AFC 0 ~ 3 1 Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC

004 STRT CHANNEL 0 ~ 127, 255 255 Channel tuned when TV is turned ON. (Set to 255 to tune to channel tuned before TV turned OFF.)

005 CHAN LOCK 0 / 1 0 If set to 1, cannot tune from current channel.

007 STRT VOLUME 0 ~ 63, 255 255 Volume level when TV is turned ON. (Set to 255 to use volume level before TV turned OFF.)

008 MIN VOLUME 0 ~ 63 0 Sets minimum allowable volume setting.

009 MAX VOLUME 0 ~ 63 63 Sets maximum allowable volume setting.

010 MUTE DISABLE 0 / 1 0 Set to 1 to disable Mute Function.

011 KEY DEFEAT 0 / 1 0 Set to 1 to disable menu navigation keys on display panel.

015 SLEEP TIMER 0 / 1 1 Set to 1 to enable Sleep Timer.

016 EN TIMER 0 / 1 0 Set to 1 to enable On/Off Timers.

017 ALARM 0 / 1 1 Set to 1 to enable Alarm.

020 FEATURE LEVEL 0 ~ 1, 16 ~ 24 1 Determines an additional IR code scheme to which the TV will respond.

021 V-CHIP 0 / 1 1 Set to 1 to enable V-Chip (Parental Control) functions.

022 MAX BLK HRS 0 ~ 99 12 Sets number of V-Chip blocking hours.

023 CAPTION LOCK 0 / 1 0 Set to 1 to retain caption setting set before TV turned OFF.

028 CH. OVERIDE 0 / 1 1 If set to 0, limits direct access to favorite channels.

029 OLD OCV 0 / 1 0 Set to 1 to change MPI operation to OCV.

030 ACK MASK 0 / 1 0 If set to 1, enables ACK feature of MPI.

031 POLL RATE 20 ~ 169 94 Selects poll rate for MPI.

032 TIMING PULSE 186 ~ 227 207 Sets baud rate for MPI.

034 CAMPORT EN 0 / 1 1 Set to 1 to enable Video 2 input.

035 COMPPORT EN. 0 / 1 1 Set to 0 to disable HDMI 1. Set to 1 enable HDMI 1.

038 YPrPb EN. 0 / 1 1 Set to 1 to enable display panel Component Video 1 input jacks.

039 REAR AUX EN 0 / 1 1 Set to 1 to enable display panel Video 1 input jack.

040 AUTO CAMPORT 0 / 1 1 Set to 1 to automatically switch to Camport. If set to 1, STRT AUX SRCE cannot be set to 2.

046 STRT AUX SRCE 1 ~ 6, 255 6 Sets the starting Aux source (if item 004 STRT CHANNEL is set to 0).

047 AUX STATUS 0 / 1 0 Set to 1 for MPI Aux source to be reported as a channel number instead of Channel 0.

053 DIS. CH-TIME 0 / 1 0 Set to 1 to disable Channel-Time display.

069 EN. CH-T COL. 0 / 1 1 Set to 1 to enable custom color for the Channel-Time display.

070 FOR. CH-TIME 0 ~ 7 2 Chooses custom foreground color for the Channel-Time display.

071 BCK. CH-TIME 0 ~ 7 2 Chooses custom background color for the Channel-Time display.

17206-4186

Installer Menu Items 073 through 119

Menu Item Function Value Range Default Value Brief Description of Function and Comments

073 CH NOT AVBLE 0 / 1 0 If set to 1 and item 028 CH. OVERIDE is set to 0, “NOT AVAILABLE” message is displayed if user direct tunes a channel that is not in the favorite channel list.

075 REVERT CH 0 / 1 0 If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel.

078 UPN MSB 0 ~ 255 0 User programmable number, most significant byte.

079 UPN MSB-1 0 ~ 255 0 User programmable number, most significant byte - 1.

080 UPN MSB-2 0 ~ 255 0 User programmable number, most significant byte - 2.

081 UPN LSB 0 ~ 255 0 User programmable number, least significant byte.

082 CHKSM ERROR 0 / 1 1 Enforces rigid MPI checksum.

083 HANDSHK TIME 0 ~ 5 5 Relaxes MPI timing to be compatible with PC-based Windows- controlled systems.

084 PERMANENT BLK 0 / 1 0 Removes block hours setting for Parental Control and makes block permanent.

087 REAR RGB EN. 0 / 1 / 17 1 Dependent on item 093 RJP AVAILABLE setting. Set to 0 to disable RGB input. Set to 1 to enable RGB input. Set to 17 for Auto Configure.

088 EN NOISE MUTE 0 / 1 1 If set to 1, audio is muted if no signal is present.

090 KEY LOCK 0 / 1 0 If set to 1, keyboard is locked out, IR is still functional.

091 YPrPb2 EN 0 / 1 1 Set to 1 to enable HDMI 2 input.

093 RJP AVAILABLE 0, 1, 2, 5, 6 0 Set to 0 to disable. Set to 1, 2, 5, or 6 for HDMI or DVI Mode. (See detailed descriptions.)

094 SAP MENU EN 0 / 1 1 Set to 0 to disable feature on Function Menu. Set to 1 to enable feature on Function Menu.

096 DEF. ASP. RATIO 0 ~ 4 2 Sets default aspect ratio at power up. See detailed descriptions and item 106.

098 PRO:CENTRIC 0 ~ 2 0 Set to 0 to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for GEM (Java Application) Mode.

099 BACK LIGHTING 1 ~ 100, 101 ~ 200, 255 100 Sets the level of the TV picture back lighting. (See detailed descriptions.)

102 ATSC BAND 0 ~ 4 4 Selects ATSC band.

103 ATSC TUNE MODE 0 / 1 1 Set to 1 (default) for Physical Channel scan. Set to 0 for Virtual Channel scan.

104 START MINOR CH 0 ~ 255 0 Selects Minor Start Channel. Set to 0 for NTSC.

106 ASP RATIO LOCK 0 / 1 0 To retain set aspect ratio on power cycle, set to 1. Set to 0 for default ratio on power cycle.

116 VIDEO MUTE EN 0 / 1 0 Set to 0 for Normal. Set to 1 for Blank.

117 FACT DEFAULT 0 / 1 0 Set to 0 for Normal. Set to 1 to load presets for all Installer Menu settings.

118 POWER SAVINGS 1 / 3 3 Set to 3 (default—b-LAN module only powered when TV is turned ON), or set to 1 (b-LAN module is always powered). (See detailed descriptions.)

119 DATA CHANNEL 0 ~ 135 0 Set to 0 to disable. Set to the RF channel number of the Data Channel for Pro:Centric or TV E-Z Installation data. (See detailed descriptions.)


Caution: Installer Menu settings may affect options available from the TV setup menus or the Function Menu.

18 206-4186


Detailed Descriptions of Installer Menu Items 000 - INSTALLER SEQUENCE Specifies entry sequence to the Installer Menu.

0 = 9876 1 = 4321 2 = 1478 3 = 3698

001 - POWER MANAGE (Power Management) Determines hours of no activity before automatic shutoff. The Power Management function is for saving energy. If set to 0, Power Manage is Off. Settings range from 0 ~ 7, with 1 ~ 7 representing the hours that the unit will remain ON, unless there has been activity from either the control panel or remote control.

002 - AC ON (AC Power Switchable) If set to 1, this allows the TV to turn ON when AC power is applied. Pressing the ON button is not necessary. This is desirable if the TV is plugged into a cable box or a power outlet controlled by a wall switch. Use the Left/Right arrow keys to choose 0 or 1, where 0 is the default (OFF), and 1 is ON.Note: If set to 1 (ON), the TV does not respond to ON/OFF commands from either the remote or the display panel, and the SLEEP TIMER is also nonfunctional.

003 - BAND/AFC (Band/Automatic Frequency Control) There are four possible settings for this option:

0 = Broadcast 1 = CATV (default) 2 = HRC 3 = IRC

If some channels were not found by Auto Tuning (Channel Search), select the appropriate Band setting here, and add the channels using the Channel Edit option in the Channel Menu.

004 - STRT CHANNEL (Start Channel)If active, this function allows you to determine the initial Major Start Channel number when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always select that channel when it is turned ON. Setting this item to 255 causes the last channel viewed when the TV was turned OFF, to be the tuned to channel when the TV is turned ON again. Note: For a digital Start Channel, always remember to set item 104 to the Minor Start Channel number.

255 = Last channel 1 ~ 125 = Major Ch. # 0 = Aux 126 = Map to Channel 3 127 = Map to Channel 4

005 - CHAN LOCK (Channel Lock) Channel Lock is ideal if the system must always be on the same channel. Changing channels with the Channel Up/Down or keypad numbers is impossible. Channel Lock is inactive if set to 0 (default).Generally, this feature is used in connection with item 004 STRT CHANNEL where the Start Channel may, for example, be set to 3 or 4. If the Start Channel is 3, then the TV will remain locked on channel 3.

NOTE: For items 007, 008, and 009For legacy reasons, the scale used is 0 – 63. The PTC software will translate this to the 0 – 100 scale used by the TV.

To translate a TV volume level to the Installer Menu value, use the following formula:

Installer Value = TV Value x 63 100

Enter only the whole number (disregard fractions).

007 - STRT VOLUME (Start Volume) This function allows the Installer to determine the initial volume level setting when the TV is turned ON. This feature is useful for an in-house information channel, since the TV would always select that volume level when it is turned ON. The range of values are 0 - 63, 255. If 255 is selected, the current volume level will be retained in memory when the TV is turned OFF; at turn ON, the volume level will be automatically set at the previous or last level.

008 - MIN VOLUME (Minimum Volume) This function determines the minimum volume level allowable with the Volume (VOL) Up/Down control. In this way, for example, someone cannot set the volume too low to hear. The value range is from 0 to 63. Use the Left/Right arrow keys to change values. The factory default is 0, which provides the full range of volume control, if item 009 MAX VOLUME is also set to 63. It may be best to set the same value on every TV. Note: The minimum volume level cannot have a value setting higher than the maximum volume level (described below).

009 - MAX VOLUME (Maximum Volume) This function determines the maximum volume level allowable with the Volume (VOL) Up/Down control. In this way, for example, someone cannot set the volume level high enough to disturb others. The value range is 0 to 63, with 63 as the default, which gives the user the full range of volume control, if item 008 MIN VOLUME is also set at 0. Use the Left/Right arrow keys to change values. It may be best to set the same value on every TV. Note: The maximum volume level cannot have a value setting lower than the minimum volume level (described above).

010 - MUTE DISABLE Enables or disables sound mute function. If set to 1, sound cannot be muted. If set to 0, sound can be muted.

011 - KEY DEFEAT (Keyboard Defeat) If set to 1, KEY DEFEAT prevents the end user from accessing the on-screen menu(s) from the display panel—MENU, ENTER, and menu navigation keys do not function. If set to 0, those keys do function. Note: Users can always access the menu(s) by pressing MENU on the remote.

19206-4186


015 - SLEEP TIMER If set to 1, the Sleep Timer feature may be used. If set to 0, the Sleep Timer is not available.

016 - EN TIMER (Enable On/Off Timers)If set to 1, the Timer function is available to the end user and enabled continuously. Set to 0 to disable On/Off timers. Note: Clock must be set in order for timers to be used.

017 - ALARMGives the installer the option of making the Alarm function avail-able to the end user. If set to 1, the Alarm function is available to the end user. Set to 0 to disable the Alarm function. Note: Clock must be set before the Alarm function will work.

020 - FEATURE LEVEL Determines an additional IR code scheme to which the TV will respond, allowing for the use of unique IR codes based on “bed number” in a multi-TV single room installation. First determine the IR mode; then select the bed number.

IR Mode Bed # ValuesLegacy (Hospital) 1 – 2 0 – 1

Multi-code Remote 1 – 9 16 – 24

Note: For further information, see documentation for the accessory package that includes the multi-code remote.

021 - V-CHIP (Parental Control) Set to 1 to activate V-Chip (Parental Control) and have it available to the end user to filter and control or otherwise restrict program-ming content that can appear. Set to 0 to turn the V-Chip feature Off (not available to user); no programming restrictions can be set.

022 - MAX BLK HRS (Maximum Block Hours) Sets hours from 0 to 99 for the maximum V-Chip (Parental Control) block hours. Default setting is for 12 blocking hours.

023 - CAPTION LOCK If set to 0, captions are OFF when the TV is turned ON. Set to 1 to use the caption setting configured before the TV was turned OFF when the TV is turned ON.

028 - CH. OVERIDE (Channel Override) If set to 1, the user can select channels with either Channel Up/Down or by direct keypad entry. If set to 0, only those channels that are active in the TV’s memory can be selected.

029 - OLD OCV (On Command Video™)Set to 1 for operation with systems from On Command Corporation.

030 - ACK MASK MPI Communication Parameter. When set to 1, enables ACK feature of MPI.

031 - POLL RATEMPI Communication Parameter. Selects poll rate for MPI. Step size of 16 ms. Changing from default may affect communication via MPI.

032 - TIMING PULSEMPI Communication Parameter. Sets baud rate for MPI. Step size of 4.3 uS. Changing from default may affect communication via MPI.

034 - CAMPORT EN. (Camera Port Enable)Set to 1 to enable Video 2 input on display panel. If set to 0, Video 2 input on display panel is not functional.

035 - COMPPORT EN. (Computer Port Enable)Enable/disable TV display panel HDMI 1 input jack. Set to 0 to disable HDMI1. Set to 1 to enable HDMI1.Note: This setting is ignored if item 093 RJP AVAILABLE is set to 1.

038 - YPrPb EN. (Rear Component Video Enable)Set to 1 to enable display panel rear Component Video input jacks. Set to 0 to disable display panel rear Component Video input jacks.

039 - REAR AUX EN. (Rear Aux Enable)Set to 1 to enable display panel rear Aux (Video 1) input. Set to 0 to disable display panel rear Aux (Video 1) input.

040 - AUTO CAMPORT Set to 1 to automatically switch to Camport when equipment is connected to side Video input. Set to 0 to disable side Video automatic source selection. If set to 1, STRT AUX SRCE cannot be set to 2.Note: If set to 1, item 093 RJP AVAILABLE is automatically set to 0.

046 - STRT AUX SRCE (Start Aux Source)Sets the starting Aux source. When turned ON, the TV will tune to starting Aux source if item 004 STRT CHANNEL is set to 0.

If item 093 RJP AVAILABLE is set to 0 and item 040 AUTO CAMPORT is set to 0:1 = Video 1 4 = RGB 255 = Last Aux 2 = Video 2 5 = HDMI 2 3 = HDMI 1 6 = Component

If item 093 RJP AVAILABLE is set to 1: 2 = Video 2 5 = HDMI 2 6 = Component

If item 040 AUTO CAMPORT is set to 1: 1 = Video 1 4 = RGB 6 = Component 3 = HDMI 1 5 = HDMI 2

047 - AUX STATUSSet to 1 for MPI Aux source to be reported as a channel number instead of channel 0. Set to 0 to disable Aux identification change. Controls MPI status channel response for Aux inputs.

20 206-4186


053 - DIS. CH-TIME (Disable Channel-Time)Set to 1 to disable the Channel-Time display; Channel-Time display will not appear. Set to 0 to enable the Channel-Time display.

069 - EN. CH-T COL. (Enable Channel-Time Custom Color)Set to 1 to enable custom color for the Channel-Time display. Set to 0 to disable custom color for the Channel-Time display.

070 - FOR. CH-TIME (Channel-Time Display Foreground Color)Set according to Color Chart:0 = Black 3 = Cyan 6 = Yellow 1 = Blue 4 = Red 7 = White 2 = Green 5 = Violet

Note: If foreground color and background color are the same, the menu background will be transparent. Note: Applies only to “Channel Not Available” message if item 073 CH NOT AVBLE is set to 1 (enabled).

071 - BCK. CH-TIME (Channel-Time Display Background Color)See description for item 070 FOR. CH-TIME above. The color chart is the same for both items.

073 - CH NOT AVBLE (Channel Not Available)If set to 1 and item 028 CH. OVERIDE is set to 0, a “NOT AVAIL-ABLE” message is displayed when a user direct tunes a channel that is not in the channel scan list available in memory.

075 - REVERT CH (Revert to Start Channel)If set to 1 and loss of MPI communication occurs, TV automatically tunes to the specified Start Channel.

078 - UPN MSB (UPN Most Significant Byte)User programmable number, most significant byte readable by MPI command. Note: Not linked to serial number.

079 - UPN MSB-1 (UPN Most Significant Byte-1)User programmable number, most significant byte-1 readable by MPI command. Note: Not linked to serial number.

080 - UPN MSB-2 (UPN Most Significant Byte-2)User programmable number, most significant byte-2 readable by MPI command. Note: Not linked to serial number.

081 - UPN LSB (UPN Least Significant Byte) User programmable number, least significant byte readable by MPI command. Note: Not linked to serial number.

082 - CHKSM ERROR (Checksum Error)Enforces rigid MPI checksum validation. Set to 1 for validation. Set to 0 to disable (does not check checksum on MPI async port). SPI is always checked.

083 - HANDSHK TIME (Handshake Time)Adds an additional delay to the handshake time which is 64 msec, thus relaxing MPI timing requirements to be compatible with PC- based Windows controlled systems. Range is 0 - 5. (Timeout = 25.5MS + [25.5 MS* Handshake time].)

084 - PERMANENT BLK (Permanent Block)Allows Lock (Parental Control) blocking schemes to be permanent by disabling the blocking hours function. Set to 1 to install Parental Control restrictions permanently. Set to 0 for user-specified hours control of blocking schemes.

087 - REAR RGB EN. (Rear RGB Enable)Controls access to rear RGB input on TV. Set to 0 to disable RGB input. Set to 1 to enable RGB input. Set to 17 to initiate a one-time automatic configuration after an AC power cycle; otherwise, automatic adjustment will be performed each time the RGB input is accessed.

088 - EN NOISE MUTE (Enable Noise Mute)If set to 1, audio mutes if no signal is present.

090 - KEY LOCK If set to 1, display panel Channel, Volume, and Caption buttons are disabled, Power button remains enabled. If set to 0, Channel, Volume, Caption, and Power buttons are all enabled.

091 - YPrPb2 EN. (HDMI2 Enable) Set to 1 to enable display panel HDMI 2 input. Set to 0 to disable display panel HDMI 2 input.

093 - RJP AVAILABLE (Remote Jack Pack Available)• 0 = Remote jack pack is not available or disabled.• 1 = Legacy Model RJPs: HDMI Mode

Enables RJP feature for use with full cable bundle models. In this mode, when an HDMI source is connected to the RJP, both digital video and audio are expected via the HDMI cable. If no digital audio is present, no audio will be heard.

• 2 = Legacy Model RJPs: DVI Mode Enables RJP feature for use with full cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via a separate cable, from the source, connected to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard.

• 5 = Scaler Model RJPs: HDMI Mode Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI source is connected to the RJP, both digital video and audio are expected via the HDMI cable. If no digital audio is present, no audio will be heard.

21206-4186

• 6 = Scaler Model RJPs: DVI Mode Enables RJP feature for use with reduced cable bundle models. In this mode, when an HDMI/DVI source is connected to the RJP, only digital video is expected via the HDMI cable. Analog audio is provided via separate cable, from the source, connect-ed to an RJP AUDIO IN. If no analog audio cable is connected, tuner audio will be heard.

Notes:See Reference section, “RJP Model List and Input Auto-sensing Hierarchy.” If RJP AVAILABLE is set to 1, 2, 5, or 6, item 040 AUTO CAMPORT is automatically set to 0. Settings 1, 2, 5, and 6 allow the lodge staff to customize each TV’s RJP setup based on customer requirements.

094 - SAP MENU EN (2nd Audio Program) Set to 1 to enable SAP feature on Function Menu, if Function Menu is available (i.e., TV is not in Pass-through Mode). Set to 0 to disable SAP feature on Function Menu, if Function Menu is available.

096 - DEF. ASP. RATIO (Default Aspect Ratio) Selects default aspect ratio at power up. • Set to 0 for Set By System.• Set to 1 for 4:3.• Set to 2 for 16:9 (Factory Default). • Set to 3 for Just Scan. • Set to 4 for Zoom. Note: Only applies if item 106 ASP RATIO LOCK is disabled, i.e., set to 0.

098 - PRO:CENTRIC Selects the Pro:Centric Application Mode. Set to 0 (default) to disable Pro:Centric operation. Set to 1 for Flash Mode. Set to 2 for GEM (Java Application) Mode.

099 - BACK LIGHTING Sets the TV screen brightness at power up. Default setting is 100.• 1 - 100 Static Back Lighting

(1 = Dimmest picture, 100 = Brightest picture)

• 101 - 200 Dynamic Back Lighting (101 = Dimmest picture, 200 = Brightest picture)

If set between 101 and 200, the TV automatically controls back lighting depending upon the picture level of the current program. If set to 255, back lighting is controlled via the Picture settings in the TV’s setup menus.

102 - ATSC BAND Sets up TV to receive different types of incoming signals: 0 = Broadcast, 1 = CATV, 2 = HRC, 3 = IRC, 4 = Same as NTSC.

103 - ATSC TUNE MODE Sets ATSC tuning mode. Default set to 1 for Physical Channel scan. Set to 0 for Virtual Channel scan.

104 - START MINOR CHANNEL Sets Minor Start Channel number at power up. 0 = NTSC. If not 0, number selected is the digital channel’s Minor Start Channel number.

106 - ASP RATIO LOCK (Aspect Ratio Lock)Set to 1 to retain previous aspect ratio with power off. Set to 0 to retain default aspect ratio with power off. See item 096 DEF. ASP. RATIO above.

116 - VIDEO MUTE EN (Video Mute Enable)Set to 0 for Normal. Set to 1 for Blank.

117 - FACT DEFAULT (Factory Default)Set to 0 for normal. Set to 1 to load presets of all Installer Menu item settings.

Caution: If set to 1, this will reload the factory defaults and clear the channel lineup, including any assigned channel icons and custom text labels.

Note: See also Reference section, “Resetting Factory Defaults on the TV(s),” for further information.

118 - POWER SAVINGS Default set to 3—the power circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port is only powered when the TV is turned ON. When the TV is in Standby Mode, the MPI card slot is powered by the Standby power supply and both the embedded b-LAN and the GAME CONTROL/MPI port are not powered. When the TV is in Power On Mode, the MPI card slot is powered by the main 12V power supply and both the embedded b-LAN and GAME CONTROL/MPI port are powered.Note that the TV must be turned ON in order to communicate with the embedded b-LAN module for configuration and control when POWER SAVINGS is set to 3. If set to 1, the b-LAN module is always powered.Similarly, if MPI communication is required for external MPI control, POWER SAVINGS should be set to 1 so that the GAME CONTROL/MPI port circuitry is always powered.Note: MPI cards with b-LAN technology—LMT7Z5, LMT7Z7, LMT7Z9—are NOT supported in TVs in which b-LAN technology is already integrated.Note: See Reference section, “b-LAN Setup & Overview,” for further information.

119 - DATA CHANNELSet to 0 (default) to disable. Set to the RF channel number of the data channel for Pro:Centric or TV E-Z Installation (splash screen, configuration, or firmware) data. Note: Pro:Centric updates are downloaded from the Pro:Centric server to the TV when the TV is turned OFF. Also, while Pro:Centric updates are in progress, it is not possible to turn the TV ON. The TV may take several minutes to load EPG data after the initial download of the Pro:Centric application. Subsequent updates generally will take less than one minute.


22 206-4186

Channel Icons / Custom Text Labels (2-5-4 + MENU Mode)

Changing a Channel’s Icon on the Master TV1. Use Channel Up/Down to select

the desired channel. 2. Use the Left/Right arrow keys

to select the thin letter “I” on the Channel-Time display.

3. Use the Up/Down arrow keys to select the icon with which you want to identify the channel. (If you know the icon number, enter the number, and press ENTER.)

4. Proceed to add/edit custom text labels, or go to the next channel.

Adding/Editing Channel Labels on the Master TV1. Use Channel Up/Down to select

the desired channel. 2. Press the Left or Right arrow

repeatedly until the numbers 1 to 7 appear on the display. The number shows the position of the character that can be changed. Number 1 is the first character, number 2 the second character, etc.

3. Use the Up/Down arrow keys to select the desired character.

4. Proceed to the next number posi-tion, or go to the next channel.

Adding/Editing Source Labels on the Master TV1. Press INPUT to select the desired

Aux input source: AV1, AV2, RGB, Component, HDMI, or HDMI2.

2. Press the Left or Right arrow repeatedly until the numbers 0 to 9 appear on the display. The number shows the position of the character that can be changed.

3. Use the Up/Down arrow keys to select the desired character.

4. Press INPUT for the next Aux input, or use Channel Up/Down to return to channels.

• Channel Up/Down: Tunes to the next channel in scan.• Left/Right Arrows: Select the item to change. If “I” is

shown, the icon can be changed. If a number is shown, it indicates the position of the character that can be changed.

• Up/Down Arrows: Select the icon or the character to be displayed. Tip: Arrows can be held down for fast scrolling.

• 0 – 9: Use to enter the index number of the icon, if known.

• ENTER: Changes the icon after the icon number has been entered.

• INPUT: Changes the Aux input label. • MENU: Exits the editing process.

Installer Remote Control Key Functions for Master TV Channel Label Editing Menu

Changing Channel Icons and/or Adding or Editing Custom Text Labels in the Channel-Time DisplayIf there is no pre-assigned icon for a channel, you can add a custom text label of up to seven (7) characters to help identify the channel or network. Also, if desired, a custom text label can be added to the Channel-Time display in addition to a pre-assigned icon. You may also add text labels for the Aux input sources to clearly identify the devices that are connected to the Aux inputs.

Changing icons and/or adding or editing custom text labels can only be done if there are channels that have been transferred to the TV’s PTC either during Master TV Setup (see pages 11 to 14) or by cloning. Note: A blank letter space is available between “Z” and “!”.

To perform channel editing/labeling:1. Enter the Installer Menu: Press MENU repeatedly until

the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6 + ENTER.

2. Press 2-5-4 + MENU on the Installer Remote to enter the Channel Label Editing Menu.

3. Change channel icons and/or add or edit custom text labels as described in the procedures below. (You can do this more than once.)

4. To exit the menu when you are done, press MENU.1 2 3 4 5 6 7

XYZXYZ XYZ

NETWORK

(Icon)

(Custom Text Label)

23206-4186

Cloning Overview

IMPORTANT CLONING INFORMATIONThere are three different procedures for cloning a Master TV Setup, each with its own advantages and limitations (see also “Cloning Methods” on page 11):• Using a USB memory device• Using a TLL-1100A clone programmer• Using a LT2002 clone programmerEach cloning method is described in further detail on the pages that follow. As you perform cloning procedures, be sure to complete each task as indicated. If a procedure or step is omitted or not performed completely, cloning may not work. At each step, pay attention to ensure the TV screen shows the proper message when cloning. If the message indicated does not appear, there is a problem with that step, and cloning may not be successful.

Caution: Copying a blank or incorrect memory into a TV from a clone programmer will cause the TV to operate erratically or become inoperable.Caution: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.

Before you begin cloning:• Complete the Master TV Setup procedure (see pages 11 to 14). • All equipment should be connected to power and turned ON. • Both the Master and Target TVs must be in Pass-through Mode.• Learning and Teaching is only possible between identical model TVs.• If using a USB memory device, ensure the USB device has been formatted with FAT format.• For both Master and Target TVs—If using a clone programmer, ensure the TV is tuned to either an Aux

input or an analog (not a digital) channel. • LT2002 only—Make sure the batteries in the clone programmer are fresh. If batteries are removed, the

clone programmer clock time (if set) will be lost (see page 29 for information on the clone programmer clock).

Caution: Do not unplug the TV power cord or remove/disconnect the USB memory device/clone programmer while Learning or Teaching, as doing so may cause the TV to malfunction or harm the USB device/clone programmer, respectively.

24 206-4186

USB Cloning Procedure

Learning / Teaching a Master TV Setup using a USB Memory Device

USB Cloning Notes• Read the IMPORTANT CLONING INFORMATION on page 23 before beginning any cloning procedures.• You may edit a filename as part of the Learning procedure; however, a file with edited contents will not

be recognized. • It is not possible to clone a Master TV’s clock using a USB memory device. Either set a Target TV’s clock

manually, or use the Auto Clock setting in the TV setup menus.

Learn From TV (TLL)

Select the file name and press OK to start

xxLD340H-UA00001.TLL

Return Enter

►

►

USB Download Menu

Upgrade TV Software

Upgrade PTC Software

Teach To TV (TLL)

Teach To TV (FMA)

Learn From TV (TLL)

Learn From TV (FMA)

Return Enter

Learn From TV

UPDATING...

Do not remove the USB from the port! Do not unplug!

!

25%

Learn Setup from Master TV1. Ensure the Master TV is set up completely and in Pass-through

Mode. 2. Plug the USB memory device into the USB IN port on the Master

TV.3. Press MENU on the Installer Remote to display the TV setup

menus. Use the arrow navigation keys to select/highlight the Option menu icon, and then press the number “7” key a total of seven times to display the USB Download Menu.

4. To gain access to the “Learn From TV” option in the USB Download Menu, key in the password used to enter the Installer Menu (Example: Press 9-8-7-6).

5. Use the Up/Down arrow keys to select Learn From TV (TLL), and then press ENTER.

6. To differentiate this .tll file from others, you can use the Up/Down arrow keys to change the last five digits of the filename. Press ENTER when you are ready to initiate Learning.

Learning status will be shown on the progress bar. When the Learning process is complete, the USB Download menu will reappear on screen.

7. When Learning is done, remove the USB memory device from the Master TV.

25206-4186

Teach To TV (TLL)

xxLD340H-UA00001.TLL

Return Enter

USB Download Menu

Upgrade TV Software


Teach To TV (TLL)

Teach To TV (FMA)

Return Enter

Teach To TV

UPDATING...

Do not remove the USB from the port! Do not unplug!

!

50%

Teach Master TV Setup to Target TV1. Ensure the Target TV is in Pass-through Mode, and then use the

Installer Remote to enter the Target TV Installer Menu: Press MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6 + ENTER.

2. Set Installer Menu item 117 FACT DEFAULT to 001, and press ENTER. When the value changes back to 0, press ENTER again to exit the Installer Menu.

3. Tune/set the TV to an analog or digital channel or Aux input, (ideally the same source tuned for 2-5-5 + MENU Mode during the Master TV Setup procedure).

4. Plug the USB memory device with the .tll file into the Target TV USB IN port.

5. Press MENU on the Installer Remote to display the TV setup menus. Use the arrow navigation keys to select/highlight the Option menu icon, and then press the number “7” key a total of seven times to display the USB Download Menu.

6. Use the Up/Down arrow keys to select Teach To TV (TLL), and then press ENTER.

7. Use the Up/Down arrow keys to select the Master TV Setup you want to install, and then press ENTER. Note: Filenames identify the TV and the TLL version (see example at right).

Teaching status will be shown on the progress bar. When the Teaching process is complete, the USB Download menu will reappear on screen.

8. When Teaching is done, remove the USB memory device from the Target TV, turn OFF the TV, and unplug the TV power cord for 15 seconds.

9. Reconnect the TV power cord, and turn ON the TV. The Master TV Setup should be resident on the Target TV.

USB Cloning Procedure (Cont.)

Learning / Teaching a Master TV Setup using a USB Memory Device (Cont.)

26 206-4186

Clone Programmer Cloning Procedures (Cont.)

Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer

Learn Setup from Master TV1. Ensure the Master TV is set up completely and in Pass-through Mode. 2. Tune/set the TV to an analog channel or Aux input, and then, plug one

end of the MPI cable into the TV MPI port. 3. Turn ON the TLL-1100A. 4. Use the MODE button on the TLL-1100A to select Clone Mode.5. Use the Left/Right arrows on the TLL-1100A to select the Memory CBank

(1 to 8) in which to store the Master TV Setup. 6. Plug the other end of the MPI cable into the MPI port on the bottom of the

TLL-1100A. The Clone Selection Menu will display on the TV screen.7. Press 1 on the Installer Remote to select LEARN FROM TV from the

Clone Selection Menu. Then, press ENTER to transfer the Master TV Setup into CBankX on the TLL-1100A.

Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will be displayed on the screen while the TLL-1100A copies the Master Setup. When the Learning process is complete, a “LEARNING COM-PLETE” message will be displayed.

8. When Learning is complete, disconnect the MPI cable from the Master TV.

Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).

TLL-1100A Cloning Notes• Read the IMPORTANT CLONING

INFORMATION on page 23 before beginning any cloning procedures.

• Ensure the TLL-1100A is either fully charged or connected to AC power.

• Learning and Teaching is only possible between identical model TVs; however, the TLL-1100A can store up to eight different Master TV Setups.

Caution: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.

Antennaor CATV

CLONE SELECTION MENUSelected Bank: CBankX Saved(1) LEARN FROM TV(2) TEACH TO TV(3) SET CLONE CLOCK FROM TV(4) SET TV CLOCK FROM CLONE(5) DISPLAY TV SETUP(6) DISPLAY CLONE SETUP

TV LinkLoader

TLL1100AReady

TLL-1100A

ENTER

RECEIVE SEND

MENUMODE

CH

AR

GE

MPI Cable

TLL-1100A Clone Programmer


CLONE CLOCK = XX:XXTV CLOCK = XX:XXTHE CLONE IS VERSION VX.X.X-

-

To change menu items, presschannel keys or digits.To execute item, press Enter.

27206-4186

(Optional) Set the Clock Set the time on a Master TV’s clock. (If the time has already been copied from a TV into the TLL-1100A clone programmer, you can set the Master TV’s clock by copying the time from the clone programmer.) The TLL-1100A can copy the current time to both a Master TV and to the clone’s internal clock—accurate to within one minute. Since the TLL-1100A’s time cannot be set directly, the current time needs to be copied from an LG TV equipped with an enabled MPI port. After the time is copied to the TLL-1100A clone programmer, the current time will be maintained and can then be transferred to another TV. (This can be a Master TV or another TV which has already had the features set up.)

Teach Master TV Setup to Target TV1. Ensure the Target TV is in Pass-through Mode, and then use the Installer

Remote to enter the Target TV Installer Menu: Press MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6 + ENTER.


3. Tune/set the TV to an analog channel or Aux input (ideally the same source tuned for 2-5-5 + MENU Mode during the Master TV Setup procedure), and then connect the MPI cable to the MPI port on the Target TV. The Clone Selection Menu will display on the TV screen.

4. Ensure the correct Memory CBank(X) is selected on the TLL-1100A. 5. Press 2 on the Installer Remote to select TEACH TO TV from the Clone

Selection Menu. Then, press ENTER to transfer the Master TV Setup to the Target TV.

Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will be displayed on the screen during Teaching. When the Teaching process is complete, a “TEACHING COMPLETE” message will be displayed.

6. When Teaching is done, disconnect the MPI cable from the Target TV, turn OFF the TV, and unplug the TV power cord for 15 seconds.




-



Learning / Teaching a Master TV Setup using a TLL-1100A Clone Programmer (Cont.)



-


28 206-4186

Learn Setup from Master TV1. Ensure the Master TV is set up completely and in Pass-through Mode. 2. Tune/set the TV to an analog channel or Aux input, and then plug one end

of the MPI cable into the TV MPI port.3. If there is a good connection after the LT2002 is connected to the TV MPI

port, “THE CLONE HAS CONTROL OF THE TV” message will appear on the TV screen. Press any key on the Installer Remote to access the LT2002 Clone Selection Menu.

4. Press 1 on the Installer Remote to select LEARN FROM TV from the Clone Selection Menu; then press ENTER to proceed to the Memory Bank Selection Menu.

5. Press 1, 2, or 3 on the Installer Remote to select the clone Memory Bank in which to store the Master Setup. Then, press ENTER.

Note: If you choose a Memory Bank that already has a Master device’s setup programmed into it, that setup will be overwritten by the new Master TV Setup.

6. Verify the Learning setup information on the next screen, and then press POWER to transfer the Master TV Setup into the selected Memory Bank on the LT2002.


Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer

LT2002 Cloning Notes• Read the IMPORTANT CLONING

INFORMATION on page 23 before beginning any cloning procedures.

• A slow flashing green light indicates that there are communication problems between the TV and the LT2002. If this is the case, check for a damaged cable, poor contacts, or other connection troubles.

• If the status indicator is red, the LT2002 batteries are low and should be replaced. Install four (4) high- quality alkaline AA batteries.

• Learning and Teaching is only possible between identical model TVs; however, the LT2002 can store up to three different Master TV Setups.

Caution: Do not connect a clone programmer to a PPV card installed in the Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.

Ferrite Core(TDK, ZCAT2035-0930)

Antennaor CATV

QuickSet II ProgrammerLT2002

®

ZENITH ELECTRONICS CORPORATION, LINCOLNSHIRE, ILLINOIS, USA

• heartbeat power on communications ok

• slow power on no communications

• green battery ok• red battery low

Blink pattern

ColorReset

StatusIndicator

Connect cable toTV MPI Jack andfollow on screeninstructions

MPI

THE CLONE HAS CONTROL OF THE TV

THE CLONE IS VERSION XXTHE TV IS VERSION XXTHE SW IS REVISION XX

CLONE CLOCK = XX:XXTV CLOCK = XX:XX

- PRESS ANY KEY TO CONTINUE.

- DISCONNECT CLONE WHEN DONE.

MPI Cable

LT2002 Clone Programmer


SAVE TV SETUP IN SELECTEDCLONE MEMORY

(1) MEMORY 1 VER XX REV XX(2) MEMORY 2 VER XX REV XX(3) MEMORY 3 VER XX REV XX(4) RETURN TO CLONE MENU

-

-

TO CHANGE MENU ITEMS, PRESSCHANNEL KEYS OR DIGITS.

TO EXECUTE ITEM, PRESS ON/OFF, POWER, OR ENTER.

COPY SELECTED CLONE MEMORY TO TV


-

-



Cloning is accomplished using the TV/clone programmer MPI ports for communication (see figure).

CLONE SELECTION MENU

(1) LEARN FROM TV(2) TEACH TO TV(3) SET CLONE CLOCK FROM TV(4) SET TV CLOCK FROM CLONE(5) DISPLAY TV SETUP(6) DISPLAY CLONE SETUP

-

-



29206-4186


Learning / Teaching a Master TV Setup using an LT2002 Clone Programmer (Cont.)


Learning usually takes about 90 seconds. “LEARNING IN PROGRESS” will be displayed on the screen while the LT2002 copies the Master Setup. When the Learning process is complete, a “LEARNING COMPLETE” message will be displayed.

7. When Learning is complete, disconnect the MPI cable from the Master TV.

(Optional) Set the Clock Set the time on a Master TV’s clock. (If the time has already been copied from a TV into the LT2002 clone programmer, you can set the Master TV’s clock by copying the time from the clone programmer.) The LT2002 can copy the current time to both a Master TV and to the clone’s internal clock—accurate to within one minute. (Another reason that the LT2002 should be equipped with fresh, high-quality alkaline batteries, is for it to keep the time as accurately as possible.)Since the LT2002’s time cannot be set directly, the current time needs to be copied from an LG TV equipped with an enabled MPI port. After the time is copied to the LT2002 clone programmer, the current time will be maintained and can then be transferred to another TV. (This can be a Master TV or another TV which has already had the features set up.)

Teach Master TV Setup to Target TV1. Ensure the Target TV is in Pass-through Mode, and then use the Installer

Remote to enter the Target TV Installer Menu: Press MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6 + ENTER.


3. Tune/set the TV to an analog channel or Aux input (ideally the same source tuned for 2-5-5 + MENU Mode during the Master TV Setup procedure), and then connect the MPI cable to the MPI port on the Target TV.

4. With “THE CLONE HAS CONTROL OF TV” message on display, press 2 on the Installer Remote to select TEACH TO TV from the LT2002 Clone Selection Menu. Then, press ENTER.

5. Select the LT2002 Memory Bank in which the new Master TV Setup is located, and press ENTER.

6. Verify the Teaching setup information on the next screen, and then press POWER to transfer the Master TV Setup to the Target TV. Teaching usually takes 3 to 4 minutes. “TEACHING IN PROGRESS” will be displayed on-screen during Teaching. When the Teaching process is complete, a “TEACHING COMPLETE” message will be displayed.

7. When Teaching is done, disconnect the MPI cable from the Target TV, turn OFF the TV, and unplug the TV power cord for 15 seconds.




-

-





-

-



SAVE TV SETUP IN SELECTEDCLONE MEMORY


-

-



COPY SELECTED CLONE MEMORY TO TV


-

-



30 206-4186

FTG Mode of Operation Overview

FTG Mode via CPU or EBLFTG Mode enables Pro:Idiom decryption and also allows logical channel mapping of physical channels. As indicated in the introduction to this document, there are two separate and distinct methods for configuring LD320H/LD325H and LD340H/LD345H TVs for FTG Mode of operation: one (new) method is to configure the TV CPU for FTG Mode operation, while the other is to configure the TV EBL for FTG Mode operation. FROM A LOCAL CONFIGURATION STANDPOINT, EACH OF THESE METHODS IS MUTUALLY EXCLUSIVE. IF THE CPU IS IN FTG MODE, THE EBL CANNOT BE SWITCHED TO FTG MODE. LIKEWISE, IF THE EBL IS IN FTG MODE, THE CPU CANNOT BE SWITCHED TO FTG MODE. Note: LD320H/LD325H TVs must have the following minimum software loads in order to support FTG Mode via CPU: CPU version 3.61 or later and PTC version 1.01.008 or later. If necessary, contact LG to obtain LD320H/LD325H CPU and PTC software files, and perform the software updates as described in Reference section, “Upgrading TV/PTC Software using a USB Memory Device.” If a Pro:Centric server is installed in the institution head end, you will also have the option to remotely reconfigure LD320H/LD325H TVs that are currently in FTG Mode via EBL for FTG Mode via CPU. Refer to the Pro:Centric™ Server Admin Client User Guide for further information.

Both FTG Mode via CPU and FTG Mode via EBL provide the following features:• Logical channels mapped to either RF delivered content.• Digital RF channel minor (program) numbers up to 255.• FTG Channel Map of up to 141 logical channels.• Start Channel set for RF or Aux input delivered content.• Pro:Centric data delivery over RF.

In addition, both FTG Mode via CPU and FTG Mode via EBL require LG FTG Device Configuration Application PC software to create an FMA Configuration (.fma) file. However, the configuration processes then diverge as follows:

FTG Mode via CPU In this mode, the CPU is the owner of the FTG Channel Map and must be configured with an FTG Channel Map and FTG Installer Menu settings using one of the following processes:• Local: Configure an individual LD320H/LD325H or

LD340H/LD345H TV via its USB port using an FMA Configuration (.fma) file on a USB memory device. The “Teach to TV (FMA)” process, along with associated procedures, is described on pages 32 to 35.

• Remote: Configure all LD320H/LD325H or LD340H/LD345H TVs at the site using a Pro:Centric server head end device (Example: PCS150R). Load an FMA Configu-ration (.fma) file on the Pro:Centric server using the TV E-Z Installation “Configuration” option in the Pro:Centric Server Admin Client. Refer to the Pro:Centric™ Server Admin Client User Guide for further information.

FTG Mode via EBLIn this mode, the EBL is the owner of the FTG Channel Map and must be configured with an FTG Channel Map and FTG Installer Menu settings using one of the following processes: • Local: Configure an individual LD320H/LD325H or

LD340H/LD345H TV’s EBL via its TV-LINK CFG jack using a direct PC-to-TV connection and the FTG Device Configuration Application. The “Write” process for an FTG Channel Map and FTG Installer Menu settings is described on page 36.

• Remote: Configure all LD320H/LD325H or LD340H/LD345H TV EBLs at the site using a Free-To-Guest Man-agement Appliance (FMA) head end device (Example: FMA-LG101). Refer to the Free-To-Guest (FTG) Con-figuration Application manual and/or the Installation & Setup manual for the FMA device for further information.

31206-4186

FTG Mode of Operation Overview (Cont.)

PICTURE AUDIO

INPUTOPTION

TIME

MY MEDIA

CHANNEL

LOCK

TV Setup MenusShows that the TV is in Pass-through Mode .

Function Menu Indicates the TV (CPU or EBL) is not in Pass-through Mode . While the TV is in FTG Mode, Installer Menu settings can be accessed as read-only.

ABC

ASPECT RATIO EnterMove

Set By Program4:316:9ZoomJust Scan

While the TV is in FTG Mode:• Users can still access the Installer Menu using an LG Installer Remote; however, all Installer Menu

items will be read-only. • Any FTG configuration changes must be made using the FTG Device Configuration Application. FTG

Channel Map Configuration and FTG Installer Menu Configuration Utilities enable you to make changes, respectively, to the FTG Channel Map and FTG Installer Menu settings as necessary. Based on the initial method used to configure the TV for FTG Mode operation (via CPU or EBL), all subsequent changes must be transferred to either the TV or the EBL via a process that is in accordance or compatible with that method (see information on local configuration in this document or refer to documentation for the head end device/server for information on remote management).

• If it becomes necessary to reset the TV to Pass-through Mode, there are several options that will enable you to do so. Refer to Reference section, “Resetting Factory Defaults on the TV(s),” for further information.

Pages 37 to 40 provide overviews of the FTG Channel Map, FTG Installer Menu, and FMA Configuration Utilities that comprise the FTG Device Configuration Application. Refer to the Free-To-Guest (FTG) Configuration Application manual for further information on the FTG Device Configuration Application.

Determining the TV Operating ModeTo determine the operating mode of the TV, press MENU on the Installer Remote. The menu display alternates based on the operating mode. See examples below.If the end user Function Menu appears, typically the TV is in FTG Mode. If the TV setup menus appear, the TV is in Pass-through Mode.

32 206-4186

FTG Mode via CPU

Creating an FMA Configuration File using the FTG Device Configuration ApplicationThis section describes how to create an FMA Configuration (.fma) file that can be saved to a USB memory device. In order to enable Pro:Idiom decryption, it is recommended that you create an FMA Configuration file using the FTG Device Configuration Application. However, if you do not know the RF channels at the site, there is an option to save (Learn) an FMA Configuration file from a TV (see “Learning an FMA Configuration File from a TV” on page 34). The procedure below provides an overview of the steps required to create an FMA Configuration file. Refer to the Free-To-Guest (FTG) Configuration Application manual for further information. See also FTG Device Configuration Application sample screens on pages 37 to 40.Note: FTG Device Configuration Application software is available online at: www.LGcommercial.com/FTGsoftware.1. Install (if necessary) and launch the FTG Device Configuration Application (v5.0.0 or higher) on the

PC that will be used to create the FMA Configuration file. 2. Either:

• Open an existing FTG Configuration (.rml) file, if applicable, to use its FTG Channel Map and/or FTG Installer Menu settings. Otherwise, create a new FTG Channel Map using the FTG Channel Map Editor in the FTG Channel Map Configuration Utility. Then, continue with step 3.Note: Up to 141 logical channels can be defined in the FTG Channel Map.

• To view and/or base a new FMA Configuration file on an existing LD320H/LD325H or LD340H/LD345H FMA Configuration file, click Configure in the FTG Device Configuration Application menu bar, and select FMA to access the FMA Configuration Utility. Then, click the Open button above the FMA Configuration List, and double-click the desired (.fma) file. A list of the file’s contents will be displayed in the FMA Configuration List window, and you can edit the FMA Configuration List as necessary to create a new file. Proceed to step 4 when you are ready to continue.

3. Click Configure in the FTG Device Configuration Application menu bar, and select FMA to access the FMA Configuration Utility.

4. To add an FTG Channel Map, click >> under FTG Channel Map to copy the current FTG Channel Map to the FMA Configuration List.

Note: If you make any change(s) in the FTG Channel Map Configuration Utility to the current data to be included in the FMA Configuration List, you will need to recopy the FTG Channel Map to the FMA Configuration List.

5. (Optional) Load default Installer Menu settings for the TV: • Click the down arrow at the right of the Chassis field under Installer Menu Templates, and select the

appropriate option (depending on the TV type) from the drop-down list of available models. • Click the Load button. • Use the FTG Installer Menu Configuration Utility to modify settings, if necessary. Then, return to the

FMA Configuration Utility.6. To add FTG Installer Menu settings, click >> under FTG Installer Menu Settings to copy the current

settings to the FMA Configuration List.Note: If you make any change(s) in the FTG Installer Menu Configuration Utility to the current data to be included in the FMA Configuration List, you will need to recopy the FTG Installer Menu settings to the FMA Configuration List.


33206-4186

FTG Mode via CPU (Cont.)

1. Plug the USB memory device that contains the FMA Configuration file into the Target LD320H/LD325H or LD340H/LD345H TV USB IN port.

2. Press MENU on the Installer Remote to display the TV setup menus (TV is in Pass-through Mode) or the Function Menu (TV is already in FTG Mode).

3. Use the arrow navigation keys to select/highlight either the Option menu icon from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the number “7” key a total of seven times to display the USB Download Menu.

4. Use the Up/Down arrow keys to select Teach To TV (FMA), and then press ENTER.

5. Use the Up/Down arrow keys to select the FMA Configuration file you want to install, and then press ENTER.

The TV will show Teaching completion progress in a new window. Do NOT remove the USB device until Teaching is complete. When Teaching is complete, the TV will tune to the first logical channel in the FTG Channel Map.

6. When Teaching is done, remove the USB memory device. The FMA Configuration should be resident on the Target TV. Also, the Target TV CPU is now in FTG Mode (if it was previously in Pass-through Mode).

Teach To TV (FMA)

xx0BAL-PLAT200001.FMA

Return Enter

USB Download Menu

Upgrade TV SoftwareUpgrade PTC SoftwareTeach To TV (TLL)Teach To TV (FMA)

Return Enter

Teach To TV

UPDATING...

Do not unplug!

!

50%

Teaching FMA Configuration to a TV This procedure describes how to “Teach” an FMA Configuration file from a USB memory device to a TV. Ensure you have completed the procedure above to create the FMA Configuration file before proceeding with the steps below. Note: If the TV EBL is already in FTG Mode, you cannot use this procedure to make changes to the FTG Channel Map and FTG Installer Menu settings. You must use a direct PC-to-TV connection as described on page 36 or an FMA head end device to reconfigure the EBL. Note: If you wish to switch the TV from FTG Mode via EBL to FTG Mode via CPU, refer to Reference section, “Resetting Factory Defaults on the TV(s),” for further information before proceeding.


7. Click the Save button above the FMA Configuration List to save its contents to an FMA Configuration (.fma) file on the PC’s hard drive for later use (default folder path is C:\Program Files\Zenith\Widget\FMA).

8. Transfer the FMA Configuration file to a USB memory device, and proceed to “Teaching FMA Configuration to a TV” below to transfer the FMA Configuration file to an LD320H/LD325H or LD340H/LD345H TV.

34 206-4186

Learn From TV (FMA)

Select the file name and press OK to start

xx0BAL-PLAT200001.FMA

Return Enter

►

►

USB Download Menu

Upgrade TV SoftwareUpgrade PTC SoftwareTeach To TV (TLL)Teach To TV (FMA)Learn From TV (TLL)Learn From TV (FMA)

Return Enter

Learn From TV

UPDATING...

Do not unplug!

! 25%

Note: It is highly recommended that you open this FMA Configuration file in the FTG Device Configuration Application—BEFORE transferring (Teaching) the file to any TVs—to verify FTG Channel Map and FTG Installer Menu settings and enable Pro:Idiom decryption by marking Encrypted channels. This will also enable you to confirm and add channel attributes, labels, etc.

Learning an FMA Configuration File from a TV To ensure that Pro:Idiom decryption is enabled, it is recommended that you create an FMA Configuration file using the FTG Device Configuration Application as described on pages 32 to 33. However, if necessary, this option enables you to save (Learn) an FMA Configuration file from an LD320H/LD325H or LD340H/LD345H TV to a USB memory device. Note: If the TV is NOT already in FTG Mode, you may need to perform some manual configuration on the TV before you start this procedure (see “Optional Manual Configuration / TV Setup” on following page).


1. Plug a USB memory device into the USB IN port on the TV.2. Press MENU on the Installer Remote to display the TV setup

menus (TV is in Pass-through Mode) or the Function Menu (TV is already in FTG Mode).

3. Use the arrow navigation keys to select/highlight either the Option menu icon from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the number “7” key a total of seven times to display the USB Download Menu.

4. To gain access to the Learn From TV options in the USB Down-load Menu, key in the password used to enter the Installer Menu (Example: Press 9-8-7-6).

5. Use the Up/Down arrow keys to select Learn From TV (FMA), and then press ENTER.

6. To differentiate this .fma file from others, you can use the Up/Down arrow keys to change the last five digits of the filename. Press ENTER when you are ready to initiate Learning.

The TV will show Learning completion progress in a new window. Do NOT remove the USB device until Learning is complete. When Learning is complete, the USB Download Menu will reappear on screen.

7. When you are finished, remove the USB memory device.

35206-4186



Note: The Installer Menu header will vary depending on the TV you are setting up.

Use Channel Menu options to run Auto Tuning and edit the channel

lineup, as necessary.

Adjust the settings for these Installer Menu items.

117 FACT DEFAULT 001

003 BAND/AFC 00X




Set Installer Menu ItemsThese steps provide specific instruction only on the Installer Menu items that should be set on an LD320H/LD325H or LD340H/LD345H TV. Refer to pages 15 to 21 for detailed information on all Installer Menu items.1. Make sure the TV is ON. Then, use the Installer Remote to enter the

Installer Menu: Press MENU repeatedly until the on-screen display of the TV setup menus no longer toggles, and then press 9-8-7-6 + ENTER.

2. Set Installer Menu item 117 FACT DEFAULT to 001 and press ENTER on the Installer Remote.

This clears all Installer Menu custom settings, the channel lineup, etc. and reloads the factory default settings. The value will change back to 0 after the commercial controller (PTC) has been restored to factory default condition. This step ensures that the TV Channel Memory will be the active channel lineup.

3. Set Installer Menu item 003 BAND/AFC, as appropriate.• Broadcast: Set to 000. • HRC: Set to 002.• CATV: Set to 001 (default). • IRC: Set to 003.

4. Set any other Installer Menu items that affect your TV programming network to the required configuration. For example, enable/disable Aux inputs, set a Start Channel, etc.

5. After you have adjusted all required Installer Menu item settings, press ENTER once on the Installer Remote to save your changes; then, press ENTER again to exit the menu.

Run Auto Tuning (Channel Search) Note: In the FMA Configuration file, Logical Channel numbers will automati-cally be assigned in ascending order, starting with 0 (zero), to the Physical Channels from the TV Channel Map.Note: Pro:Idiom decryption for encrypted channels will not be enabled unless you use the FTG Device Configuration Application to set channel attributes. 1. Search for all available analog and digital channels: Use the Installer

Remote to go to the Channel Menu, select the Auto Tuning option, and follow the on-screen instructions.

2. Use the Channel Edit option in the Channel Menu to edit the channel lineup, as necessary, to include free to guest channels only. Add/delete channels per your system requirements.

Optional Manual Configuration / TV SetupThe manual configuration procedures below should only be performed if you do not know the RF channels at the site and need to “Learn” an FMA Configuration file from an LD320H/LD325H or LD340H/LD345H TV as described on the previous page. Ensure the TV is in Pass-through Mode before you begin.

Once you have completed these procedures, return to “Learning an FMA Configuration File from a TV” on the previous page to complete the Learn sequence.

CHANNEL EnterMove

Auto TuningManual TuningChannel EditChannel Label

36 206-4186

AUDIO IN(RGB/DVI)

RS-232C IN(SERVICE ONLY)

. . . . .. . . .

VIDEO L/MONO-AUDIO-R

AV IN 1

TV-LINKCFG

GAME CONTROL/

MPI

REMOTECONTROL OUT

COMPONENT IN

RLPBY PR

VIDEO AUDIO

ANTENNA IN

LaptopPC

The following steps outline local FTG configuration of individual TV EBLs using a direct PC-to-TV connection. Refer to the Free-To-Guest (FTG) Configuration Application manual for further information. See also FTG Device Configuration Application sample screens on pages 37 to 40.

Notes: • FTG Device Configuration Application software is available online at: www.LGcommercial.com/FTGsoftware.

• If the TV CPU is already in FTG Mode, you cannot use this procedure to make changes to the FTG Channel Map and FTG Installer Menu settings. Instead, refer to and use the processes described on pages 32 and 33 to reconfigure the TV CPU.

• If the preceding condition applies, but you wish to switch the TV to FTG Mode via EBL, refer to Reference section, “Resetting Factory Defaults on the TV(s),” for further information before proceeding.

TV-LINK CFGUse for direct PC-to-TV

FTG configuration.

USB-to-TTL Serial Cable Required for direct PC-to-TV FTG configuration.

FTG Mode via EBL

Notes: • ANTENNA IN connector located on jack panel on

26LD320H, 26LD340H, and 26LD345H only.• Dual-purpose GAME CONTROL/MPI port on

26LD320H and LD340H/LD345H TVs only. On 32/37/42LD320H and 32/37LD325H TVs, the MPI port is located on the same plate as the RF Antenna jack.

1. Install (if necessary) and launch the FTG Device Configuration Application (v5.0.0 or higher) on the PC that will be used to configure the EBL.

2. Build an FTG Channel Map using the FTG Channel Map Editor in the FTG Channel Map Configuration Utility (or, if applicable, open an existing FTG Configuration [.rml] file).Note: Up to 141 logical channels can be defined in the FTG Channel Map.

3. Connect the PC to the TV-LINK CFG jack on the TV’s rear connections panel using a USB-to-TTL serial cable (TTL-232R-5V-AJ). If necessary, install the device driver on the PC.

4. Turn ON the TV. Note: If Installer Menu item 118 POWER SAVINGS is set to 3 (default), the TV must be ON in order for steps 5 and 6 below to be successful.

5. “Write” the FTG Channel Map to the EBL (switches the EBL from Pass-through Mode to FTG Mode).Note: After a “Write” of new data, the TV will briefly display a green text banner that shows the EBL firm-ware version and release date.

6. “Read” the current FTG Installer Menu settings from the EBL using the FTG Installer Menu Configuration Utility. If necessary to make changes to Installer Menu items, “Write” them back to the EBL in FTG Mode.

7. Save the FTG Channel Map and FTG Installer Menu settings to an FTG Configuration (.rml) file for future use.

8. Tune the TV to a Logical Channel in the FTG Channel Map.

Rear Jack Panel

37206-4186

FTG Channel Map Configuration UtilityThe FTG Channel Map Configuration Utility enables you to build a Channel Map with logical channel numbers. Note: Write, Read, and Learn functions in the FTG Channel Map Configuration Utility are used for direct PC-to-TV FTG configuration of LD320H/LD325H and LD340H/LD345H TVs (FTG Mode via EBL). These functions are not applicable to the process of creating an FMA Configuration file to be saved to a USB memory device (FTG Mode via CPU).

PRINT MAP Click to display a printable

FTG Channel Map Report. The report can also be exported as

an HTML or Text file.

EDIT/ADD MAPClick to open the FTG Channel Map

Editor to create or edit an FTG Channel Map (see next page).

FTG Device Configuration Application Utilities Overview

WRITEClick to transfer the FTG Channel Map to the EBL. This will switch the EBL from Pass-through Mode to FTG Mode.

READClick to transfer the FTG Channel Map from the EBL to the FTG Device Configuration Application.

LEARNClick to transfer the TV Channel Map from the PTC to the EBL and the FTG Device Configuration Application. (Requires that 2-5-5 + MENU was performed to transfer TV Channel Map to PTC.) *

* Logical Channel numbers will automatically be assigned in ascending order, starting with 0 (zero), to the Physical Channels from the TV Channel Map.

Filename of opened FTG Configuration (.rml) file.

38 206-4186

FTG Device Configuration Application Utilities Overview (Cont.)

DELETEClick to remove highlighted channel from FTG Channel Map.

ADDAfter defining a new Logical Channel, click to add channel to the FTG Channel Map.

FTG Channel Map Editor The FTG Channel Map Editor shows a single Logical Channel’s Data and the FTG Channel Map.

EXIT Click to exit editor and return to FTG Channel Map Configuration Utility.

LOGICAL CHANNEL MAPPINGSelect a Logical Channel number, then assign it the RF, Major, and Minor chan-nel numbers to complete the mapping.

CUSTOM CHANNEL LABELS/ICONSEnter custom labels and select icons by name on menu or by number.

SET CHANNEL ATTRIBUTESCheck/select Encrypted, OSD, or Blank Video.

UPDATEAfter editing an existing Logical Channel’s data, click to commit the changes in the FTG Channel Map.

39206-4186

WRITEClick to transfer the FTG Installer Menu settings to the EBL.


CONFIGURATION SETTINGSSelect tabs for categories of Installer Menu items to set up TV.

HOSPITAL-GRADE TV ONLYSet Hospital items on Installer Menu for hospital-grade TV models.

FTG Installer Menu Configuration Utility Note: Write, Read, Learn, and IR Remote Access functions in the FTG Installer Menu Configuration Utility are used for direct PC-to-TV FTG configuration of LD320H/LD325H and LD340H/LD345H TVs (FTG Mode via EBL). These functions are not applicable to the process of creating an FMA Configuration file to be saved to a USB memory device (FTG Mode via CPU).

LEARNClick to transfer Installer Menu settings from the PTC to the EBL and FTG Device Configuration Application. *

INSTALLER DEFAULTSClick to reset FTG Installer Menu items shown in the FTG Device Configuration Application to defaults.

READClick to transfer the Installer Menu settings in the EBL to the FTG Device Configuration Application.

IR REMOTE ACCESSToggle IR Remote Access to ON to obtain access to TV setup menus and Installer Menu.

* Logical Channel numbers will automatically be assigned in ascending order, starting with 0 (zero), to the Physical Channels from the TV Channel Map.


40 206-4186

Note: The data referenced in the FMA Configuration List is only a snap-shot of the current FTG Channel Map and FTG Installer Menu settings when copied to the list. If you make any change(s) to the current data to be included in the FMA Configuration List, you will need to recopy Channel Map and Installer Menu settings to the FMA Configuration List.


Load default FTG Installer Menu for LD320H/LD325H

or LD340H/LD345H.

Copy FTG Installer Menu settings to and from FMA

Configuration List.

Copy FTG Channel Map to and from FMA

Configuration List.

FMA CONFIGURATION LIST (data to be saved or already saved in FMA Configuration file)

FMA Configuration Utility Note: FMA Write, Read, Clock, Broadcast, Firmware, and IP Communication functions in the FMA Configuration Utility are used to configure b-LAN enabled equipment (Example: FMA-LG101) at the hotel/institution head end. These functions are not applicable to the process of creating an FMA Configuration file to be used with LD320H/LD325H and LD340H/LD345H TVs (FTG Mode via CPU).

NEW/OPEN/SAVEFMA File options


41206-4186

Remote Jack Pack Setup RJP Available? If you will use a Remote Jack Pack (RJP) in your system, set Installer Menu item 093 RJP AVAILABLE appropriately (for example, on a legacy model RJP: HDMI Mode, set RJP AVAILABLE to 001). See Installer Menu detailed descriptions for further information.

TV Connections Make these connections ONLY after Master TV Setup and TV cloning procedures are complete.

Refer to the figure below, and connect the RJ-45 Control cable from the RJP cable bundle to the RJP INTERFACE port on the TV’s jack panel. Then, connect HDMI, RGB, and Composite Video/Audio connectors, as applicable, for the cable bundle.

Remote Jack Pack / TV Connections & Setup

UPDATERESET

AUDIO IN(RGB/DVI)


. . . . .. . . ...........2

1HDMI/DVI IN

RJP


AV IN 1

RGB IN (PC)

. . . . .. . . . .. . . . .TV-LINK

CFG

GAME CONTROL/

MPI..........

REMOTECONTROL OUT

SPEAKER OUT 8

HDMI

COMPONENT IN

RLPBY PR

VIDEO AUDIO( )

ANTENNA IN

HDMI/DVI IN 1 Connect HDMI connector from RJP cable bundle.

RJPConnect RJ-45 Control cable

from RJP cable bundle.

RGB IN (PC)Connect RGB connector from RJP cable bundle (legacy RJP only).

AUDIO/VIDEO IN 1Connect Composite Video/Audio connectors from RJP cable bundle. (Composite Video on legacy RJP only.)

093 RJP AVAILABLE 001

Notes: • ANTENNA IN connector located on jack panel on 26LD320H, 26LD340H, and 26LD345H only.• Dual-purpose GAME CONTROL/MPI port on 26LD320H and LD340H/LD345H TVs only. On

32/37/42LD320H and 32/37LD325H TVs, the MPI port is located on the same plate as the RF Antenna jack.

42 206-4186

Reference: Upgrading TV/PTC Software using a USB Memory Device

Upgrading TV/PTC Software Before you begin, note that the software upgrade files must be stored in a folder named “LG_DTV” in the root directory of the USB memory device. Also, ensure the USB device has been formatted with FAT format.Note for TV Software Upgrade only: If the TV detects a later version of software on the USB device, it will automatically display a dialog from which you can start the software upgrade immediately. Otherwise, you can close the dialog, and access the USB Download Menu as described below. 1. Turn the TV ON.2. Plug the USB memory device into the USB IN port on the TV. 3. Press MENU on the Installer Remote to display the TV setup menus (TV is in

Pass-through Mode) or the Function Menu (TV is not in Pass-through Mode).4. Use the arrow navigation keys to select/highlight either the Option menu icon

from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the number “7” key a total of seven times to display the USB Download Menu.

5. Use the Up/Down arrow keys to select Upgrade TV Software or Upgrade PTC Software, as applicable, and press ENTER.

6. Select the appropriate option(s), depending on the type of upgrade:• TV Software Upgrade: (See screen samples at right.) Select TV Software

Update from the first TV Software Update window. In the second TV Software Update window, select/highlight the update file to install and press ENTER. Note: Do not select Forced Update options unless you have been specifically instructed to do so or have previous experience with Expert Software Updates.

• PTC Software Upgrade: In the PTC Software Update window, select/highlight the update file to install and press ENTER. Note: The PTC Software Update window is similar to the second TV Soft-ware Update window, though there are no Forced Update options. Current software version information is shown at the top and update files on the USB device are listed at the bottom of the window.

Checking the Software VersionsYou can check the software versions of the TV by accessing the Installer Menu with the Installer Remote: Press MENU repeatedly until the on-screen menu display no longer toggles, and then press 9-8-7-6 + ENTER. When you are finished, press ENTER again to exit the Installer Menu.


CPU VersionPTC Version

TV Software Update (Expert)

TV Software Update

LOGO Image Download


[ Current TV Software Version Information ]

EPK : 03.03.00

xxLD340H_v1_00_RevNo1000_USB

The following software files are found in the memory card.Select the file you want to download to this TVor press EXIT to cancel the update.

EPK : 03.05.00

[ Forced Update Option ]

Ext. MICOM SPI Boot

LOGO Image

[ Current PTC Software Version Information ]

TXT : 03.03.00

xxLD340H_v1.01.00

The following software files are found in the memory card.


Splash Image 1366 X 768 ProCentric



TV Software Update

LOGO Image Download



TV Software Update

LOGO Image Download



EPK : 03.03.00



EPK : 03.05.00


Ext. MICOM SPI Boot

LOGO Image


TXT : 03.03.00

xxLD340H_v1.01.00






TV Software Update

LOGO Image Download


The TV will show update completion progress in a new window. Do NOT remove the USB device until the software upgrade is complete. When a TV software upgrade is complete, the TV will reset itself with an automatic restart. When a PTC upgrade is complete, the TV will turn OFF.




USB Download Menu

Upgrade TV Software


Teach To TV (TLL)

Teach To TV (FMA)

Return Enter

43206-4186

Reference: Downloading a Splash Screen using a USB Memory Device

Splash Screen Image File Guidelines • The splash screen image must be a baseline (not progressive) JPEG.• The image should be no larger than 1 MB.• The ideal size for the image is 1366 x 768 pixels or under.• The image file must be stored in a folder named “LG_DTV” in the root

directory of USB memory device.• Ensure the USB device has been formatted with FAT format.

Downloading a Splash Screen Image1. Turn the TV ON.2. Plug the USB memory device into the USB IN port on the TV. 3. Press MENU on the Installer Remote to display the TV setup menus (TV is in

Pass-through Mode) or the Function Menu (TV is not in Pass-through Mode).4. Use the arrow navigation keys to select/highlight either the Option menu icon

from the TV setup menus or the Lock menu icon from the Function Menu. Then, press the number “7” key a total of seven times to display the USB Download Menu.

5. Use the Up/Down arrow keys to select Upgrade TV Software, and then press ENTER.

6. Select LOGO Image Download from the first TV Software Update window. 7. In the second TV Software Update window, use the Up/Down arrow keys to

select the image file to download, and then press ENTER. The TV will show download completion progress in a new window. Do NOT remove the USB device until the image download is complete. When the image download is complete, the TV will reset itself with an automatic restart. Upon the restart, you should see the new splash screen.


TV Software Update

LOGO Image Download



EPK : 03.03.00



EPK : 03.05.00


Ext. MICOM SPI Boot

LOGO Image


TXT : 03.03.00

xxLD340H_v1.01.00






TV Software Update

LOGO Image Download



TV Software Update

LOGO Image Download



EPK : 03.03.00



EPK : 03.05.00


Ext. MICOM SPI Boot

LOGO Image


TXT : 03.03.00

xxLD340H_v1.01.00






TV Software Update

LOGO Image Download


USB Download Menu

Upgrade TV Software


Teach To TV (TLL)

Teach To TV (FMA)

Return Enter

44 206-4186

Reference: Power Consumption Settings

26/32/37/42LD320H & 32/37LD325H

The following tables assume that Installer Menu item 118 POWER SAVINGS is set to 003 (default) and Installer Menu item 099 BACK LIGHTING is set as shown below (default value is 100).

Item 099 Back Lighting

(Static)

26LD320H 32LD320H / 32LD325H 37LD320H / 37LD325H 42LD320H

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

100 56.82 0.00% 72.97 0.00% 88.92 0.00% 107.53 0.00%90 51.98 8.52% 63.82 12.54% 84.19 5.32% 86.68 19.39%80 47.09 17.13% 58.53 19.78% 77.84 12.46% 78.79 26.73%70 42.06 25.97% 53.58 26.57% 72.19 18.81% 72.81 32.29%60 39.71 30.12% 44.24 39.38% 66.28 25.46% 66.78 37.89%50 37.36 34.25% 41.27 43.45% 60.90 31.51% 60.61 43.63%40 36.31 36.10% 38.71 46.95% 56.58 36.37% 56.35 47.60%30 35.12 38.19% 36.20 50.39% 52.35 41.13% 52.90 50.81%20 32.59 42.64% 33.51 54.07% 47.75 46.30% 47.71 55.63%10 30.23 46.80% 31.01 57.51% 43.68 50.88% 43.04 59.98%1 27.95 50.82% 28.55 60.87% 39.62 55.44% 38.86 63.86%


(Dynamic)

26LD320H 32LD320H / 32LD325H 37LD320H / 37LD325H 42LD320H

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

200 72.19 0.00% 75.45 0.00% 110.86 0.00% 125.41 0.00%190 68.21 5.51% 69.23 8.25% 99.05 10.65% 111.41 11.16%180 63.72 11.74% 65.26 13.51% 92.33 16.72% 103.30 17.63%170 59.21 17.99% 60.72 19.53% 85.39 22.98% 95.29 24.02%160 55.04 23.76% 56.29 25.40% 78.61 29.10% 87.64 30.11%150 50.81 29.62% 51.82 31.33% 71.70 35.32% 79.71 36.44%140 46.03 36.24% 46.62 38.21% 63.53 42.69% 70.73 43.60%130 41.49 42.53% 41.67 44.78% 55.65 49.80% 61.80 50.72%120 36.32 49.69% 36.14 52.10% 47.34 57.30% 51.86 58.65%110 31.52 56.34% 31.11 58.76% 39.90 64.01% 42.90 65.79%101 26.95 62.67% 26.41 65.00% 33.00 70.24% 34.52 72.47%

Note: Values are results of controlled experiments under laboratory conditions.

45206-4186

Reference: Power Consumption Settings (Cont.)

26/32/37/42LD340H & 26/32/37/42LD345H


(Static)

26LD340H / 26LD345H 32LD340H / 32LD345H 37LD340H / 37LD345H 42LD340H / 42LD345H

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

100 56.82 0.00% 72.97 0.00% 88.92 0.00% 107.53 0.00%90 51.98 8.52% 63.82 12.54% 84.19 5.32% 86.68 19.39%80 47.09 17.13% 58.53 19.78% 77.84 12.46% 78.79 26.73%70 42.06 25.97% 53.58 26.57% 72.19 18.81% 72.81 32.29%60 39.71 30.12% 44.24 39.38% 66.28 25.46% 66.78 37.89%50 37.36 34.25% 41.27 43.45% 60.90 31.51% 60.61 43.63%40 36.31 36.10% 38.71 46.95% 56.58 36.37% 56.35 47.60%30 35.12 38.19% 36.20 50.39% 52.35 41.13% 52.90 50.81%20 32.59 42.64% 33.51 54.07% 47.75 46.30% 47.71 55.63%10 30.23 46.80% 31.01 57.51% 43.68 50.88% 43.04 59.98%1 27.95 50.82% 28.55 60.87% 39.62 55.44% 38.86 63.86%


(Dynamic)

26LD340H / 26LD345H 32LD340H / 32LD345H 37LD340H / 37LD345H 42LD340H / 42LD345H

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

Power Consumption

(Watts)

Percent Savings

200 72.19 0.00% 75.45 0.00% 110.86 0.00% 125.41 0.00%190 68.21 5.51% 69.23 8.25% 99.05 10.65% 111.41 11.16%180 63.72 11.74% 65.26 13.51% 92.33 16.72% 103.30 17.63%170 59.21 17.99% 60.72 19.53% 85.39 22.98% 95.29 24.02%160 55.04 23.76% 56.29 25.40% 78.61 29.10% 87.64 30.11%150 50.81 29.62% 51.82 31.33% 71.70 35.32% 79.71 36.44%140 46.03 36.24% 46.62 38.21% 63.53 42.69% 70.73 43.60%130 41.49 42.53% 41.67 44.78% 55.65 49.80% 61.80 50.72%120 36.32 49.69% 36.14 52.10% 47.34 57.30% 51.86 58.65%110 31.52 56.34% 31.11 58.76% 39.90 64.01% 42.90 65.79%101 26.95 62.67% 26.41 65.00% 33.00 70.24% 34.52 72.47%

Note: Values are results of controlled experiments under laboratory conditions.

46 206-4186

Reference: TV Camport Auto Sense Operation

The Camport Auto Sense function is enabled when:1. Installer Menu item 034 CAMPORT EN is set to 1 AND2. Installer Menu item 040 AUTO CAMPORT is enabled (1).

Selectable: Can be accessed with INPUT key, direct access, etc.Auto Sense: TV switches to this input when connector is inserted. The Camport (Side [AV IN 2] Video) has the highest priority and will override any commands including tuning to the Start Channel.

CAMPORT (Side Video) Functionality ControlItem 034

CAMPORT ENItem 040

AUTO CAMPORTSide (AV IN 2)

Video Operation0 0 Disabled0 1 Disabled1 0 Selectable1 1 Auto Sense

Camport Operation (Stand-alone)When Camport Auto Sense is enabled as above, the TV will switch from its current source to the Side (AV IN 2) Video input whenever a plug is inserted into the AV IN 2 Video input.When the video plug is removed, the TV will switch back to the previous source that was being displayed before the plug was inserted. However, if any direct access to an Aux channel or RF channel is requested while the Camport is active, then, when the video plug is removed, the TV will switch to the last requested channel. Source changes using any Source keys (INPUT) are ignored. Channel Up/Down and Flashback commands are not Direct Access tuning commands, and they are also ignored.

Previous State Before Inserting

CAMPORT

Operation While CAMPORT is

Active

State Upon Removal of CAMPORT

Aux or RF Channel None Previous Aux

or RF ChannelAux or RF Channel Direct Access Last Requested

Aux or RF Channel

Aux or RF Channel

Ch Up/Down, Flashback, and

Input Keys

Previous Auxor RF Channel

Camport Operation (FTG or PPV)The operation will be similar to that of the Pass-through Mode. However, when the Channel Map is maintained external to the PTC (i.e., FTG and PPV), Channel Up/Down or Flashback keys are sent as Direct Access tuning commands to the PTC/TV.

Previous State Before Inserting

CAMPORT

Operation While CAMPORT is

Active

State Upon Removal of CAMPORT

Aux or RF Channel None Previous Aux

or RF Channel

Aux or RF Channel Direct Access Last Requested

Aux or RF Channel

Aux or RF Channel

Ch Up/Down, Flashback, and

Input Keys

Last Requested Aux or RF Channel

47206-4186

Reference: TV Aux Input Configuration

DIRECT ACCESS Tuning TV

ENABLE MPI DATA

START AUX SOURCE ASSIGN-

MENT

Installer Menu

MPI DATA STATUS TYPE

0x41 SOURCES ENABLED (R/W)

DATA STATUS TYPE 0xD2

CURRENT AVSOURCE (R)

DATA STATUS TYPE 0x0D

AUXSOURCE (R)OLD_

OCV = 0OLD_

OCV = 1Source Input

Source Mode

Number Labeling Value Labeling Value Labeling

130 90 Video2 (Side)

CV 34 CAMPORT_EN 0x01 Video Front (Camport)

0 Video Front (Camport)

0 (VIDEO) 2

131 91 Video1 (Rear)

CV 39 REAR_AUX_EN 0x02 Rear Video (Aux)

1 Rear Video (Aux)

0 (VIDEO) 1

132 92 HDMI2 DTV/PC 91 YPrPb2 EN = 1 0x04 S-Video Rear 2 S-Video Rear 0 (VIDEO) 5

133 93 HDMI1/DVI DTV/PC 35 COMPPORT_EN = 1

0x08 Front Computer

3 Front Computer

0 (VIDEO) 3

134 94 RGB PC 87 REAR RGB EN = 2

0x10 SVGA Rear Computer

4 SVGA Rear Computer

2 (COMPUTER)

4

136 96 Component 38 YPrPb EN 0x40 Y/UV Component

6 Rear Y/PrPb Component

Video

0 (VIDEO) 6

48 206-4186

Reference: b-LAN Setup & Overview

A b-LAN enabled head end device, such as an LG FMA-LG101, broadcasts over the RF distribution system to communicate to multiple TVs. When the TV is first installed, it must be turned ON in order for its embedded b-LAN module to receive communication from the head end device. At this point, if it is desired for the b-LAN module to always be powered, including while the TV is in Standby, set Installer Menu item 118 POWER SAVINGS to 001. Also, if MPI communication is required for external MPI control, set Installer Menu item 118 POWER SAVINGS to 001 so that the GAME CONTROL/MPI port circuitry is always powered.

The b-LAN module is internal to the TV. It allows hotel/institution head end equipment with b-LAN technology to communicate, via the institution’s RF distribution system, with the TV for configuration and control. Note: MPI cards with b-LAN technology—LMT7Z5, LMT7Z7, LMT7Z9—are NOT supported in TVs in which b-LAN technology is already integrated. Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port (see note below). The default value is 003—the b-LAN module is only powered when the TV is turned ON. See chart below.Note: 26LD320H and all LD340H/LD345H TVs have a dual-purpose GAME CONTROL/MPI port on the TV rear jack panel. On 32/37/42LD320H and 32/37LD325H TVs, the MPI port is located on the same plate as the RF Antenna jack.

POWER SAVINGS

001 On On

003 (default) Off On

TV Power On StateTV Standby State

b-LAN & GAME CONTROL/MPI Port

Power

b-LAN & GAME CONTROL/MPI Port

Power

49206-4186

Reference: RJP Model List and Input Auto-sensing Hierarchy

RJP Model List

Legacy Models Scaler Models

RJP-101M N/A

RJP-101ML N/ARJP-110F RJP-210FRJP-110FW RJP-210FW

RJP-110W RJP-210WRJP-110WBR RJP-210WBRRJP-110S RJP-210SRJP-120G RJP-220G

RJP-120T RJP-220T

RJP-201B RJP-301B

RJP-202B RJP-302B

RJP Input Auto-sensing Hierarchy

Priority Video Audio

1st (Highest) Digital Video In Audio In (3.5mm)

2nd PC Video In Audio In (L/R)3rd Video In Digital Video In

50 206-4186

This section describes how to reset factory defaults either on a single TV that is currently in Pass-through Mode or on multiple TVs that are currently in FTG Mode.Note: If the TV(s) is/are currently in FTG Mode, restoring the factory defaults also resets the TV to Pass-through Mode.

Installer Menu Item 117 FACT DEFAULTIf the TV is currently in Pass-through Mode, you can set Installer Menu item 117 FACT DEFAULT to 001 to reload the factory defaults and clear the channel lineup, including any assigned channel icons and custom text labels.

Factory “IN-STOP”If the TV is currently in FTG Mode, a predefined value for Installer Menu item 117 FACT DEFAULT enables access to initiate a factory “IN-STOP” process that will reset the TV to Pass-through Mode in addition to restoring all factory defaults. Contact technical support for the required value for Installer Menu item 117 and for additional information on performing the IN-STOP from the Installer Menu.

Additional FTG Mode via CPU OptionsThere are two additional options for resetting Pass-through Mode/factory defaults on TVs that are in FTG Mode via the CPU. The first enables you to reset a single TV to Pass-through Mode, while the second enables you to reset multiple TVs to Pass-through Mode at one time.• Using a USB memory device, “Teach” an FMA Configuration file that only contains a “0 Mapped

Channels” FTG Channel Map to the TV. Refer to “Creating an FMA Configuration File using the FTG Device Configuration Application” and “Teaching FMA Configuration to a TV” on pages 32 and 33, respectively, for further information.

• If your system uses a Pro:Centric server for remote management/administration, use the Pro:Centric Admin Client to load an FMA Configuration file that only contains a “0 Mapped Channels” FTG Channel Map on the Pro:Centric server. Refer to the Pro:Centric™ Server Admin Client User Guide for further information.

Additional FTG Mode via EBL OptionsThere are two additional options for resetting Pass-through Mode/factory defaults on TVs that are in FTG Mode via the EBL. The first enables you to reset a single TV to Pass-through Mode, while the second enables you to reset multiple TVs to Pass-through Mode at one time.

Note: While the IN-STOP process described above will clear both the PTC and the CPU, both options below only clear the PTC. Thus, the current Channel Map and TV setup menu settings will remain in the CPU after the reset is completed.

• Using a direct PC-to-TV connection, “Write” an unpopulated Channel Map—that is, a Channel Map with zero channels—to the TV. Refer to the “FTG Mode via EBL” procedure on page 36 and/or the Free-To-Guest (FTG) Configuration Application manual for further information.

• If your system uses an FMA for remote management/broadcast configuration, configure the FMA device with an FMA Configuration file that only contains a “0 Mapped Channels” FTG Channel Map to broad-cast to the TV EBL(s). Refer to the Free-To-Guest (FTG) Configuration Application manual and/or the Installation & Setup manual for the FMA device for further information.

Reference: Resetting Factory Defaults on the TV(s)

51206-4186

UPDATERESET

AUDIO IN(RGB/DVI)


. . . . .. . . ...........2

1HDMI/DVI IN

RJP


AV IN 1

RGB IN (PC)

. . . . .. . . . .. . . . .TV-LINK

CFG

GAME CONTROL/

MPI..........

REMOTECONTROL OUT

SPEAKER OUT 8

HDMI

COMPONENT IN

RLPBY PR

VIDEO AUDIO( )

ANTENNA IN

Reference: LD320H/LD325H & LD340H/LD345H Rear Jack Panel

RGB IN (PC)Connection for RGB

output from PC.

TV-LINK CFGUse for direct PC-to-TV FTG configuration.

UPDATERestricted to

software updates.

RESETInitiates a hardware

reset and switches the TV to standby.

GAME CONTROL/MPI **When the TV/EBL is in Pass-through Mode, the MPI function enables an external MPI control device (i.e., clone programmer, VOD/PPV STB, etc.) to control the TV. Game Control—EBL in LodgeNet PPV Mode only.

AUDIO/VIDEO IN 1Connection for composite audio/ video output from external device.

SPEAKER OUT (8Ω) *Connect to 8 ohm self-powered speaker input. Intended for special applications, such as a powered bath-room speaker with volume control.

REMOTE CONTROL OUTIR output for controlling an auxiliary device.

RS-232C INUse for downloading software updates, etc.

COMPONENT IN Connection for component output from external device.

AUDIO IN (RGB/DVI) Audio connection for RGB or DVI device.

RJPConnection for Remote Jack

Pack (RJP) Control cable.

HDMI/DVI IN Connection for HDMI/DVI

output from external device.

ANTENNA IN26LD320H, 26LD340H, & 26LD345H only. Connect to Antenna/CATV.

* This stereo jack provides a mono speaker fixed-level, 1 watt output (audio +, audio -, w/ground shield). Do NOT plug in a mono connector, as this may damage the TV.

** On 32/37/42LD320H and 32/37LD325H TVs, this is a GAME CONTROL port only. GAME CONTROL function as described above. On these TVs, the MPI port is located on the same plate as the RF Antenna jack (see next page).

52 206-4186

Reference: Side Connections Panel / RF Antenna & MPI Connections

AV IN 2

L/M

ON

O -A

UD

IO- R

VID

EOU

SB INUSB IN

Insert USB memory device for software updates, cloning

purposes, FTG Mode via CPU configuration, picture/music

entertainment, etc., as applicable.

Antennaor CATV

AN

TENN

A IN

MP I

RF Antenna & MPI Connections

Side Connections Panel

VIDEO INConnect to video output port on external device (see Reference section, “TV Camport Auto Sense Operation,” for further information).

L/MONO-AUDIO-R INConnect to audio output jacks on external device. For only mono audio output, connect to Left audio input.

A/V 2 Input

ANTENNA IN Connect to Antenna/CATV.

Notes:

• On 26LD320H, 26LD340H, and 26LD345H TVs, the RF Antenna jack is on the rear jack panel (see previous page).

• On 26LD320H and all LD340H and LD345H TVs, the MPI port is located on the rear jack panel (dual-purpose GAME CONTROL/MPI port).

MPIEnables an external MPI control device (i.e., clone programmer, VOD/PPV STB, etc.) to control the TV when the EBL is in Pass-through Mode.

53206-4186

Troubleshooting

General Troubleshooting

Some Quick and Easy Tips for Resolving Problems

Symptom Possible Cause(s) Possible Solution(s)

InstallationCannot direct enter channel number.

(TV in Pass-through Mode) Installer Menu item 028 CH. OVERIDE is set to 0, i.e., disabled (recommended setting).

If Installer Menu item 028 CH. OVERIDE is set to 0, only channels that are active in the TV’s channel lineup can be selected. Set CH. OVERIDE to 1 to allow access for direct keypad entry to all channels.

(TV in FTG Mode) The channel entered is not part of the FTG Channel Map.

Channel access is restricted to channels included in the FTG Channel Map. If necessary, make changes to the FTG Channel Map using the FTG Device Configuration Application.

PowerNo power. See troubleshooting flow chart on following page.

Display Panel PictureNo picture. Display panel is turned off. • Turn TV ON.

• Power failure?

Antenna/cable not connected. Connect antenna/cable signal to TVConnections incorrect. Check connections on TVMPI not connected. If applicable, connect MPI cable to MPI device.Encrypted program. Try another channel.Wrong tuning band. Adjust Installer Menu settings.

Erratic OperationInstaller Menu setup. Wrong Installer Menu settings. Adjust Installer Menu settings as required.

Installer RemoteRemote doesn’t work. Remote not in TV Mode. Use MODE key to select “TV”; puts remote into TV Mode.

Not aimed at IR remote sensor. Point remote at IR receiver on TV.Remote too far from IR sensor. Move remote closer to IR receiver on TV or darken room.MPI not connected. If applicable, connect MPI cable to MPI device.IR path to TV’s receiver obstructed. Remove obstructions.Weak batteries. Replace batteries.Wrong battery polarity. Check that “+” and “-” match in battery compartment.Too much light in room. Dim room light.Wrong Installer Remote. Requires compatible Installer Remote. Contact your LG

dealer. Picture ReceptionNormal picture, poor or no sound.

Audio muted. Press MUTE or use Volume Up key to increase sound level.

Broadcast problem. Try a different channel.

Note: For other problems not caused by the TV, refer to the other devices’ operating guide(s).

54 206-4186

ControllerQuick Check

STATUS LED on PTC

Board blinking?

Plug into AC Power outlet.

TV connected

to AC Power?

BadTV

Yes

No No

Yes

Cycle the power by removing and reconnecting the AC Power cord. Then,

observe POWER LED on front of TV.

POWERLED lit?

No

Yes

Press POWER on LG Installer Remote.

TVresponded?

No

Yes

TVresponded?

No

Yes

End

BadTV

Contact system integrator for additional

troubleshooting assistance.

Bad Digital Board

TV turned ON?

Yes

No

Press VOLUME UP/DOWN or MUTE key

on LG Installer Remote.

BadTV

Press VOLUME UP/DOWN or MUTE key on

in-room or system integrator-supplied remote.

Troubleshooting (Cont.)

Troubleshooting Flow Chart

55206-4186


Commercial Mode Check / FTG Operation Troubleshooting

TV turned ON?

Yes

No

Press POWER on Installer Remote.

TV is not in Commercial Mode. Call Technical

Support for assistance.

TV is inCommercial Mode.

NoOn-screen

menu display no longer toggles?

Yes

Press MENU repeatedly as if to access the

Installer Menu.

Function Menu

on display?

Leave the TV set ON, and press MENU on the

Installer Remote.

No

TV is inCommercial Mode.

Yes

Plug into AC Power outlet.

TV connected

to AC Power?

BadTV

No

Yes

Commercial Mode Check Use this flowchart to determine whether the TV is currently in Commercial Mode.

FTG Operation Troubleshooting The following table provides troubleshooting information for when the EBL is configured in the FTG Mode of operation.

Symptom Possible Cause(s) Solution(s)

Communication Error (“Communications Timeout”)

Cable(s) not connected. Check and connect communication cables.

TV not powered. Check/connect the TV power cord.

TV not turned ON. TV needs to be turned ON (default FTG Mode).

Wrong COM (communication) port.

In the FTG Device Configuration Application, select the correct COM port for the cable being used.

56 206-4186

Caution: Do not connect a clone programmer to a PPV card installed in the

Master or Target TVs. Also, if the TV is in LodgeNet PPV Mode (check with the site administrator if you are not certain), do not connect a clone programmer to the GAME CONTROL/MPI port. Either of these actions will damage the clone programmer and, if applicable, the PPV card.

• After cloning operations are complete, unplug the TLL-1100A/LT2002 from the TV.• If the TV does not display a picture (blank screen) after a few seconds, just change channels.


Clone Programmer Troubleshooting

Reset Clone Programmer After Static ShockAfter replacing exhausted batteries (LT2002 only), or if the clone programmer behaves strangely after a static shock:• TLL-1100A: Turn the TLL-1100A OFF and then ON. • LT2002: Use a paper clip or similar instrument inserted through the small hole

marked RESET to activate the internal reset switch and restore normal operation. After a reset, check the real-time clock setting. It may be necessary to set the clone programmer clock from a TV containing the correct time.Note: Both the Master and Target TVs must be in Pass-through Mode for cloning purposes. See also IMPORTANT CLONING INFORMATION on page 23.

Clone ProgrammerSymptom Possible Cause(s) Possible Solution(s)Clone copies setup in less than 30 seconds.

Not enough time to copy entire TV setup.

TLL-1100A: Turn the TLL-1100A OFF and then ON. LT2002: Press RESET on clone programmer.Then redo Learn/Teach. (Learning usually takes about 90 seconds; Teaching usually takes 3 to 4 minutes.)

Remote does not operate clone programmer.

Wrong Installer Remote. Only use an LG Installer Remote to operate clone programmer with TV.

Clone menu does not dis-play on TV screen, TLL-1100A shows error mes-sage, or LT2002 LED does not blink.

MPI cord not connected. Connect MPI cord properly, and ensure good connection.TV not turned ON. TV must be powered ON for clone programmer to work.

(LT2002 only) Weak batteries. Install four (4) fresh AA high-quality alkaline batteries.(TLL-1100A only) No charge. Ensure the TLL-1100A is fully charged or connected to AC power.

Clone menu hard to read. Weak signal. Connect TV to a reliable analog channel signal source.

No time set. Time not available. Set time on a TV, and copy time to clone programmer.

Clone not working. Clone programmer problem. • Try a different clone programmer.• Reset the clone programmer.

Clone scans channels more than once.

Clone should only scan channels once.

Ensure TV is set up correctly, and try cloning again.

Master and Target TVsSymptom Possible Cause(s) Possible Solution(s)Cloning did not work. Procedure interrupted. Wait until procedure complete message is displayed.

Different TV models. Cloning is only possible with identical model TVs.Step(s) omitted or not performed. Refer to the applicable cloning procedure(s), and make sure all

tasks were performed.

(LT2002 only) Clone time disappeared.

Batteries were removed. Batteries must remain installed to retain time settings.

New setup not present. Target TV not reset. Disconnect Target TV from AC power for 15 seconds.

57206-4186

75 OHM RF CABLE The wire that comes from an off-air antenna or cable service provider. The end looks like a hex-shaped nut with a wire through the middle. It screws onto the Antenna/Cable threaded jack on the back of the TV.

300 TO 75 OHM ADAPTER A small device that connects a 2-wire 300 ohm antenna to a 75 ohm RF jack. It is usually about an inch long with two screws on one end and a round opening with a wire extending out the other end.

A/V CABLES Audio/Video cables. Three cables bunched together —right audio (red), left audio (white), and video (yellow). A/V cables are used for stereo playback of videocassettes and for higher quality pic-ture and sound from other A/V devices.

A/V DEVICE Any device that produces video or sound (VCR, DVD, cable box, or television).

AMPLIFIER An electronic device that amplifies sound from a television, CD player, VCR, DVD player, or other Audio/Video device.

ANTENNA The physical receiver of television signals sent over the air. A large metal piece of equipment does not always have to be visible to be using an antenna.

b-LANLodgeNet Interactive Corporation proprietary RF communication system used to configure/control TV via RF distribution system.

CABLE Cable service box. Refers to the descrambler box cable subscribers use to receive cable programming signals.

CATVProgramming provided by a cable service.

COMPONENT VIDEOUses three wires for transporting three-color video signals. The end result is usually better video quality.

COMPOSITE VIDEOTypical video jack, uses one wire for transporting three-color video signals.

DELETE Lets you remove channels from the list that the end user can scroll through using Channel Up/Down.

DIGITAL TELEVISION High-resolution, cinema-quality television signals transmitted digitally.

DVI Digital Video Interface. Accommodates analog and digital interfaces with a single connector.

HDMI High-definition multi-media interface.

HDSTB High-definition set top box. Refers to a tuner device that receives high-definition television signals which have higher res-olution than ordinary analog TV signals.

HDTV High-definition television. Refers to tele-vision signals that have higher resolu-tion than ordinary analog TV signals.

INPUT Refers to the input jack that receives a signal from a TV, VCR, DVD Player, or other Audio/Video device.

JACK An input or output connector on the back of a TV, VCR, DVD Player, or other Audio/Video device.

MONO SOUND Mono (monaural) sound is one channel of sound. On more than one speaker, all the speakers play the same audio.

OUTPUT Refers to the output jack that sends a signal out of a VCR, DVD, or other A/V device.

PHYSICAL CHANNEL NUMBERThe actual channel number. Analog channels use the Physical Channel number and digital channels can use a Virtual Channel number.

RGB (RED, GREEN, BLUE)Connection input or output port available for producing a video image using three separate colors: Red, Green, and Blue.

RS-232Serial communication port through which firmware is downloaded.

2ND AUDIO PROGRAMMING/SAP Second Audio Programming (SAP) is another, separate audio channel avail-able with some programming. Choosing SAP often refers to listening to audio in another language, such as Spanish or French.

SIGNAL Picture and sound traveling through a cable, or over the air, to the TV.

STEREO SOUND Stereo (Stereophonic) sound refers to audio that’s divided into right and left sides.

TUNER Device that picks up the broadcast sig-nal and turns it into picture and sound.

VIRTUAL CHANNEL NUMBER A re-mapped channel number. Analog channels use the Physical Channel number; however digital channels use a Virtual (or false) Channel number.

XDS Extended Data Service. Additional program information included on the signal provided at the discretion of the broadcaster.

Glossary of Terms

A list of definitions for some of the words found in this guide.

Note: Refer to www.atsc.org for further information.

58 206-4186

Document Revision History / Notes

Notes

Document Revision History

Date DescriptionMay 2011 Revision A: New documentNovember 2011 Revision B: LD320H/LD325H models added to document, also updates for external

MPI control

Product documentation is available online at: www.LGsolutions.com/products. From the Products page, select TVs, Systems & Solutions, then LCD TVs, then the applicable TV. Click the Literature & Downloads tab at the bottom of the TV page, and select the required document(s) from the Downloads list.

206-4186Revision B© Copyright 2011, LG Electronics U.S.A., Inc.

For Customer Support/Service, please call:

1-888-865-3026 www.LGsolutions.com

Pro:Idiom is a registered trademark of Zenith Electronics LLC. Pro:Centric is a trademark of LG Electronics U.S.A., Inc. b-LAN is a trademark of LodgeNet Interactive Corporation. All other

trademarks or registered trademarks are the property of their respective owners.

26ld320h 32ld320h 37ld320h 42ld320h …€¦ · master tv setup pages 11 – 14 cloning information...

Documents