3 e electronics 241110
DESCRIPTION
Parallel circuits.Introducing resistance: S3TRANSCRIPT
![Page 1: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/1.jpg)
Electricity
3E: Wednesday 24th November
![Page 2: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/2.jpg)
Parallel circuits• In a parallel circuit, current has more than one
path in which to flow around the circuit:
Vsupply
I1I2 I3
V1V2 V3
Isupply
![Page 3: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/3.jpg)
Experiment
• Aim: Measuring current and voltage in a parallel circuit
• Set up parallel circuit as shown• Measure the voltage across the cells (Vsupply) and
the voltage across each lamp (V1, V2, V3, V4)
• Measure the current through each lamp (I1, I2, I3, I4) and the current drawn from the supply, Isupply
![Page 4: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/4.jpg)
Parallel circuits: Conclusions
• The sum of all currents in the parallel branches in the circuit is equal to the current drawn from the supply:
Isupply = I1 + I2 + I3 + …
• The voltage across components in parallel are the same and equal to the supply voltage
Vsupply = V1 = V2 = V3 = …
![Page 5: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/5.jpg)
Uses of series circuits
• Torches, old-style Christmas lights…• Stair lighting uses two or more 2-way switches
in series:
Power Supply
Downstairs switch
Upstairs switchLamp
This circuit is in the OFF positionEither switch will turn the light ON
![Page 6: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/6.jpg)
Uses of parallel circuits• New style Christmas lights• Car lighting circuits:
MM
Ignition switch
Side & rearlamps
Headlights
Startermotor
Wipermotor
![Page 7: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/7.jpg)
ResistanceLearning Objectives:• Know what resistance is and what units
we measure it in
Starter
Write down as many meanings for the word resistance as you can in 1 minute!
![Page 8: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/8.jpg)
Experimental setup
1. Set up the circuit as shown2. Turn on the power supply and adjust the voltage across the lamp to 12V3. Take readings of the voltage and current and record in a table in your workbook4. Repeat this for several different values (12V down to 0V) of the voltage and
measure both voltage and current through the lamp in your table of results5. Replace the lamp in the circuit with a resistor and repeat steps 2-4 using a new
table and graph6. Plot a graph of your results (voltage (V) on y-axis; current (A) on x-axis) for both
the lamp and the resistor
![Page 9: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/9.jpg)
Definition of Resistance• Electrical Resistance of an object is a measure of its opposition to the passage
of an electric current• Resistance is measured in Ohms (Ω)
Resistance = voltage / current
R=V/I V=IR I=V/R
George Simon Ohm
German Physicist
V
I R
![Page 10: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/10.jpg)
Resistors
• Resistors are simple components used to control the current and voltage in a circuit
![Page 11: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/11.jpg)
Resistive heating
• For a given component, power P = IV where I is the current through that component and V is the voltage across that component
• Substituting from V=IR we get:P = I2R = V2/R = IV
Power is measured in Watts
![Page 12: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/12.jpg)
Resistors in series
• If we join resistors in series we increase the resistance of the circuit. The current will decrease
• The total resistance in series is equal to the sum of the individual resistances:
Rs = R1 + R2 + R3
where Rs = equivalent series resistance
![Page 13: 3 e electronics 241110](https://reader034.vdocument.in/reader034/viewer/2022052619/55622d15d8b42ab6588b5538/html5/thumbnails/13.jpg)
Resistors in parallel
• If we join components in parallel we decrease the resistance of the circuit. The current will increase.
• The combined resistance in parallel is calculated using the formula:
1/RP = 1/R1 + 1/R2 + 1/R3
where RP = equivalent parallel resistance