3- final exam v4.0 answers 8 jan 2011

CCNA FINAL EXAM 2011

Search

CCNA FINAL

CCNA 4 Chapter 8 V4.0 Answers ccna final exam answers update 2011

CCNA 4, CCNA 4 Final Exam, CCNA 4 Final Exam Answers, CCNA 4 – Accessing the WAN(V4.0)

Add comments

CCNA 4 Final Exam V4.0 AnswersJan

082011

CCNA 4 Final Exam V4.0 Answers Updated 2011 100%1. What functionality do access control lists provide in the implementation of dynamic NAT on a Ciscorouter?

define which addresses can be translated

define which addresses are assigned to a NAT pool

define which addresses are allowed out the router

define which addresses can be accessed from the inside network

2. Which three guidelines would help contribute to creating a strong password policy? (Choose three.)

Once a good password is created, do not change it.

Deliberately misspell words when creating passwords.

Create passwords that are at least 8 characters in length.

Use combinations of upper case, lower case, and special characters.

Write passwords in locations that can be easily retrieved to avoid being locked out.

Use long words found in the dictionary to make passwords that are easy to remember.

3.

Refer to the exhibit. Every time the administrator reboots this router, the boot process ends in setupmode. What is a possible problem?

There is insufficient RAM for the IOS to load on this router.

A password recovery process should be done on this router.

The bootstrap version and the version of the IOS are different.

The IOS image is damaged and must be reloaded using tftpdnld.

The configuration register is set to ignore the startup configuration.

4. Which option correctly defines the capacity through the local loop guaranteed to a customer by theservice provider?

BE

DE

CIR

CBIR

5.

CCNA 1CCNA 1 Final Exam

CCNA 1 – Network Fundamentals(V4.0)


CCNA 2 Skill 2011

CCNA 2 – Routing Protocols andConcepts (V4.0)


CCNA 3 – LAN Switching andWireless (V4.0)


CCNA 4 Final Exam Answers

CCNA 4 – Accessing the WAN (V4.0)

ccna final 2011

Uncategorized

Categories

About

CCNA 2011 Exam AnswersCCENT Practice Certification Exam

CCNA 1 Exam Answers

CCNA 2 Exam Answers

CCNA 3 Exam Answers

CCNA 4 Exam Answers

CCNA Practice Certification Exam

CCNA Discovery 4.1 Answers

Packet tracer

Pass4sure CCNA

TestInside ccna 640-802

CCNA 1 ccna 1 2011ccna 1 answers ccna 1 chapter 3

ccna 1 chapter 3 100 2911 ccna 1 chapter 3 2011

ccna 1 chapter 3 answers CCNA 1 Chapter 3 V4.0

Answers 100 Updated 2011 CCNA 1 Final CCNA

1 Final Exam CCNA 1 Final Exam Answers CCNA

1 final exam answers 2010 CCNA 1 final exam

answers 2011 CCNA 1 Final Exam Questions and

Answers 2010 ccna 1 module 3 CCNA2 ccna 2 2011 ccna2 exploration 4.0CCNA 3 ccna 3 2011 CCNA 3 Final

CCNA 3 Final Exam CCNA 3 Final Exam Answers

CCNA 4 CCNA4 FinalCCNA 4 Final CCNA 4Final Exam ccna4 final exam

CCNA 4 Final ExamAnswers CCNA 4 Final Exam Answers

(3) ccna 4 final exam answers 2010ccna 4 final exam answers 2011 CCNA4 Final Exam Questions and Answers2010 ccna 2011 ccna answers 2011

CCNA Exploration 4 Chapter 5 Answers

ccna exploration 4.0CCNA Final ccna final 2010 ccna final exam

Tags

CCNA 4 Final Exam V4.0 Answers | CCNA FINAL http://www.ccnafinal.org/ccnaanswers/ccna-4-final-exam-v4-0-answers...

1 of 13 Create PDF files without this message by purchasing novaPDF printer (http://www.novapdf.com)م 08:38 24/11/2011

http://www.novapdf.com


Refer to the exhibit. A host connected to Fa0/0 is unable to acquire an IP address from the DHCP server.The output of the debug ip dhcp server command shows “DHCPD: there is no address pool for 10.1.1.1″.What is the problem?

The 10.1.1.1 address is already configured on Fa0/0.

The default router for the 10Network pool is incorrect.

The ip helper-address must be added to Fa0/0 interface.

The pool of addresses for the 10Network pool is incorrect.

6. Which data link layer encapsulation protocol is used by default for serial connections between twoCisco routers?

ATM

Frame Relay

HDLC

PPP

SDLC

7.

Refer to the exhibit. Which statement correctly describes how Router1 processes an FTP request thatenters interface s0/0/0 and is destined for an FTP server at IP address 192.168.1.5?

The router matches the incoming packet to the statement that was created by the access-list 201 deny icmp192.168.1.0 0.0.0.255 any command, continues comparing the packet to the remaining statements in ACL 201to ensure that no subsequent statements allow FTP, and then the router drops the packet.

The router reaches the end of ACL 101 without matching a condition and drops the packet because there is nostatement that was created by the access-list 101 permit ip any any command.

The router matches the incoming packet to the statement that was created by the access-list 101 permit ip any192.168.1.0 0.0.0.255 command and allows the packet into the router.

It matches the incoming packet to the statement that was created by the access-list 201 permit ip any anycommand and allows the packet into the router.

8. Compared with IDS systems, what can IPS systems do to provide further protection of computersystems?

detect potential attacks

stop the detected attack from executing

update OS patches for computer systems

scan computer systems for viruses and spyware

9. Which IEEE 802.16 broadband wireless technology allows users to connect to the ISP at speedscomparable to DSL and cable?

Wi-Fi

satellite

WiMAX

Metro Ethernet

10. A network administrator has changed the VLAN configurations on his network switches over the pastweekend. How can the administrator determine if the additions and changes improved performance andavailability on the company intranet?

ccna final exam 2011 ccna finalexam answers 4.0 CCNA Module

1 Answers CCNA Module 2 Answers CCNA

Module 3 Answers

Which layers should support QoS in ahierarchical network?, Refer to the exhibit Anetwork administrator is configuring ausername and password for an SSHconnection On checking the configurationthe administrator notices that the passwordis displayed as plain text What configurationmethod can be used to encrypt, Whichstatement is true about wildcard masks?,ccna2 final exam 2011, Refer to the exhibitVLAN 20 was recently added on the networkUsers on VLAN 20 on SW1 startcomplaining that they do not haveconnectivity to the users on the same VLANon switch SW2 What should be done toremedy the problem?, Refer to the exhibitThe network consists of hundreds of routersbranched from connected regionaldistribution sites using single area OSPFRecent network failures caused packetflooding and route recalculations in allbranch networks What should the engi,Refer to the exhibit A technician istroubleshooting a trunk problem betweenswitches SW1 and SW2 What should bedone to remedy the problem?, A recentlypatched application server is experiencingresponse time problems The network onwhich the application server is located hasbeen experiencing occasional outages thatthe network team believes may be related torecent routing changes Network an, ewanfinal exam, A network administrator is taskedwith maintaining two remote locations in thesame city Both locations use the sameservice provider and have the same serviceplan for DSL service When comparingdownload rates it is noticed that the locationon the East , Refer to the exhibit SwitchSW2 has been newly purchased and addedto the network What configuration should beapplied to SW2 so that it participates in thesame VTP domain as switch SW1 receivesVLAN information from SW1 andsynchronizes VLAN information, ccna3 finalexam answers 2011, which layers shouldsupport qos in a hierarchical network, ccna 3final exam answers 2011, ccna4 final exam2011, Refer to the exhibit PC1 PC2 and PC3are configured with dynamic addressassignments PC2 is assigned an IP addressfrom the DHCP server What would accountfor the IP addresses that are currentlyassigned to PC1 and PC3?, ccna 3 finalexam 2011, At what physical location doesthe responsibility for a WAN connectionchange from the service provider to theuser?, At what physical location does theresponsibilty for a WAN connection changefrom the user to the service provider?, ccnafinal exam 2011, A company has a remotebranch office that uses a cable modemconnection to communicate with the mainoffice What type of WAN connection isestablished at the branch office?, Whichstatement is true about wildcard masks,ccna 3 final 2011, EWAN Final Exam 2011,ccna3 final exam 2011, ewan final examanswers 2011, Refer to the exhibit Acompany has acquired a new office in acampus environment Switches in the

Tags



Ma7moud

Pencil

Ma7moud

Pencil



Conduct a performance test and compare with the baseline that was established previously.

Interview departmental secretaries and determine if they think load time for web pages has improved.

Determine performance on the intranet by monitoring load times of company web pages from remote sites.

Compare the hit counts on the company web server for the current week to the values that were recorded inprevious weeks.

11.

Refer to the exhibit. What is the meaning of the term dynamic in the output of the command?

The bandwidth capability of the interface increases and decreases automatically based on BECNs.

The Serial0/0/1 interface acquired 172.16.3.1 from a DHCP server.

The mapping between DLCI 100 and 172.16.3.1 was learned through Inverse ARP.

DLCI 100 will automatically adapt to changes in the Frame Relay cloud.

12. Which type of ACL will permit traffic inbound into a private network only if an outbound session hasalready been established between the source and destination?

extended

reflexive

standard

time-based

13. Which two statements are true about IPv6 link local addresses? (Choose two.)

They begin with the 2000::/3 prefix.

They begin with the FE80::/10 prefix.

They are assigned by IANA to an organization.

They must be manually configured by the administrator.

They are assigned to a host by a stateless autoconfiguration process.

14. A company is looking for a WAN solution to connect its headquarters site to four remote sites. Whatare two advantages that dedicated leased lines provide compared to a shared Frame Relay solution?(Choose two.)

reduced jitter

reduced costs

reduced latency

the ability to burst above guaranteed bandwidth

the ability to borrow unused bandwidth from the leased lines of other customers

15.

Refer to the exhibit. A network administrator is trying to connect R1 remotely to make configurationchanges. Based on the exhibited command output, what will be the result when attempting to connect toR1?

failure to connect due to Telnet not being enabled

failure to connect due to incomplete configuration for Telnet

a successful connection and ability to make configuration changes

existing office and the new office are directlyconnected by a trunk link The VLANs and IPaddressing are setup as shown in the exhibitThe computers in each , Refer to the exhibitA technician is teaching a trainee to interpretthe results of various Frame Relaytroubleshooting commands What conclusioncan be drawn from the output that isshown?, ccna 3 final exam v4 0 answers2011, lan switching and wireless final exam2011

Angry Bird

Angry Birds Chrome

Angry Birds Online

Angry Birds Online

ccna blog

ccna exam

ccna exploration

ccna4u

friv 4 School

packet tracer

packet tracer

packet tracer 5.3.1

packet tracer 5.3.1

packet tracer download

y8y8

Link



Ma7moud

Pencil

Ma7moud

Pencil



a successful connection but inability to make configuration changes because of the absence of an enable secretpassword

16. What are two effective measures for securing routers? (Choose two.)

Protect all active router interfaces by configuring them as passive interfaces.

Configure remote administration through VTY lines for Telnet access.

Use quotes or phrases to create pass phrases.

Disable the HTTP server service.

Enable SNMP traps.

17. An issue of response time has recently arisen on an application server. The new release of asoftware package has also been installed on the server. The configuration of the network has changedrecently. To identify the problem, individuals from both teams responsible for the recent changes beginto investigate the source of the problem. Which statement applies to this situation?

Scheduling will be easy if the network and software teams work independently.

It will be difficult to isolate the problem if two teams are implementing changes independently.

Results from changes will be easier to reconcile and document if each team works in isolation.

Only results from the software package should be tested as the network is designed to accommodate theproposed software platform.

18.

Refer to the exhibit. From the output of the show interfaces and ping commands, at which layer of theOSI model is a fault indicated?

application

transport

network

data link

physical

19. Which technology is used to dynamically map next hop, network layer addresses to virtual circuits ina Frame Relay network?

Inverse ARP

LMI

DLCI

FECN

20. An administrator learns of an e-mail that has been received by a number of users in the company.This e-mail appears to come from the office of the administrator. The e-mail asks the users to confirmtheir account and password information. Which type of security threat does this e-mail represent?

cracking

phishing

phreaking

spamming

21.





Refer to the exhibit. Which data transmission technology is being represented?

TDM

PPP

HDLC

SLIP

22.

Refer to the exhibit. Results of the show vlan and show vtp status commands for switches S1 and S2 aredisplayed in the exhibit. VLAN 11 was created on S1. Why is VLAN 11 missing from S2?

There is a Layer 2 loop.

The VTP domain names do not match.

Only one switch can be in server mode.

S2 has a higher spanning-tree priority for VLAN 11 than S1 does.

23. What is the result of adding the global command service password-encryption to the configuration ofa router?

Line passwords are encrypted with type 7 encryption.

Enable passwords are encrypted with type 5 encryption.

All services must provide an encrypted password to function.

Only encrypted messages are allowed for router communication.

24. While troubleshooting a problem with an e-mail server, an administrator observes that the switchport used by the server shows “up, line protocol up”. The administrator cannot ping the server. At whichlayer of the OSI model is the problem most likely to be found?

application layer

network layer

data link layer

physical layer

25. Where does a service provider assume responsibility from a customer for a WAN connection?

local loop

DTE cable on router

demarcation point

demilitarized zone

26. What will be the result of adding the command ip dhcp excluded-address 192.168.24.1 192.168.24.5 tothe configuration of a local router that has been configured as a DHCP server?

Traffic that is destined for 192.168.24.1 and 192.168.24.5 will be dropped by the router.

Traffic will not be routed from clients with addresses between 192.168.24.1 and 192.168.24.5.

The DHCP server will not issue the addresses ranging from 192.168.24.1 to 192.168.24.5.

The router will ignore all traffic that comes from the DHCP servers with addresses 192.168.24.1 and192.168.24.5.

27.





Refer to the exhibit. Partial results of the show access-lists and show ip interface FastEthernet 0/1commands for router Router1 are shown. There are no other ACLs in effect. Host A is unable to telnet tohost B. Which action will correct the problem but still restrict other traffic between the two networks?

Apply the ACL in the inbound direction.

Apply the ACL on the FastEthernet 0/0 interface.

Reverse the order of the TCP protocol statements in the ACL.

Modify the second entry in the list to permit tcp host 172.16.10.10 any eq telnet .

28.

Refer to the exhibit. The corporate network that is shown has been assigned network 172.16.128.0/19 foruse at branch office LANs. If VLSM is used, what mask should be used for addressing hosts at Branch4with minimal waste from unused addresses?

/19

/20

/21

/22

/23

/24

29.

Refer to the exhibit. RIPv2 has been configured on all routers in the network. Routers R1 and R3 havenot received any RIP routing updates. What will fix the issue?

Enable RIP authentication on R2.

Issue the ip directed-broadcast command on R2.

Change the subnet masks to 10.11.12.0/8 and 172.16.40.0/16 on R2.

Enable CDP on R2 so that the other routers will receive routing updates.

30.

Refer to the exhibit. This serial interface is not functioning correctly. Based on the output shown, what isthe most likely cause?

improper LMI type

interface reset

PPP negotiation failure

unplugged cable

31. Which statement is true about PAP in the authentication of a PPP session?

PAP uses a two-way handshake.

The password is unique and random.

PAP conducts periodic password challenges.

PAP uses MD5 hashing to keep the password secure.

32. An administrator is configuring a dual stack router with IPv6 and IPv4 using RIPng. The administratorreceives an error message when trying to enter the IPv4 routes into RIPng. What is the cause of theproblem?





When IPv4 and IPv6 are configured on the same interface, all IPv4 addresses are over-written in favor of thenewer technology.

Incorrect IPv4 addresses are entered on the router interfaces.

RIPng is incompatible with dual-stack technology.

IPv4 is incompatible with RIPng.

33. What is tunneling?

using digital certificates to ensure that data endpoints are authentic

creating a hash to ensure the integrity of data as it traverses a network

using alternate paths to avoid access control lists and bypass security measures

encapsulating an entire packet within another packet for transmission over a network

34. Which statement is true about NCP?

Link termination is the responsibility of NCP.

Each network protocol has a corresponding NCP.

NCP establishes the initial link between PPP devices.

NCP tests the link to ensure that the link quality is sufficient.

35.

Refer to the exhibit. A network administrator is creating a prototype to verify the new WAN design.However, the communication between the two routers cannot be established. Based on the output of thecommands, what can be done to solve the problem?

Replace the serial cable .

Replace the WIC on RA.

Configure RA with a clock rate command.

Issue a no shutdown interface command on RB.

36.

Refer to the exhibit. Based on the output as shown, which two statements correctly define how therouter will treat Telnet traffic that comes into interface FastEthernet 0/1? (Choose two).

Telnet to 172.16.10.0/24 is denied.

Telnet to 172.16.20.0/24 is denied.

Telnet to 172.16.0.0/24 is permitted.



37. Which Frame Relay flow control mechanism is used to signal routers that they should reduce theflow rate of frames?

DE

BE

CIR

FECN





CBIR

38.

Refer to the exhibit. A network administrator configures a standard access control list on Router1 toprohibit traffic from the 192.168.0.0/24 network from reaching the Internet. The access control list alsopermits traffic from the 192.168.0.0/24 network to reach the 192.168.1.0/24 network. On which interfaceand in which direction should the access control list be applied?

interface Fa0/0, inbound

interface Fa0/0, outbound

interface S0/0/0, inbound

interface S0/0/0, outbound

39. Which configuration on the vty lines provides the best security measure for network administratorsto remotely access the core routers at headquarters?

Answer: 3nd option

40.

Refer to the exhibit. What can be concluded from the exhibited output of the debug ip nat command?

The 10.1.1.225 host is exchanging packets with the 192.168.0.10 host.

The native 10.1.200.254 address is being translated to 192.168.0.10.

The 192.168.0.0/24 network is the inside network.

Port address translation is in effect.

41. A network administrator is instructing a technician on best practices for applying ACLs. Whichsuggestion should the administrator provide?

Named ACLs are less efficient than numbered ACLs.

Standard ACLs should be applied closest to the core layer.

ACLs applied to outbound interfaces are the most efficient.

Extended ACLs should be applied closest to the source that is specified by the ACL.

42.

Refer to the exhibit. Headquarters is connected through the Internet to branch office A and branch officeB. Which WAN technology would be best suited to provide secure connectivity between headquartersand both branch offices?

ATM

VPN

ISDN

Frame Relay

broadband DSL

43. Which three physical network problems should be checked when a bottom-up troubleshootingapproach has been chosen to troubleshoot network performance? (Choose three.)

cable connectivity

high collision counts

STP failures and loops





address mapping errors

high CPU utilization rates

excess packets that are filtered by the firewall

44.

Refer to the exhibit. A network administrator is attempting to configure a Frame Relay network. Theadministrator enters the commands as shown in the exhibit on R2, but the Frame Relay PVCs areinactive. What is the problem?

The incorrect DLCI numbers are being configured on R2.

The S0/0/0 interface on R2 needs to be point-to-point.

The frame-relay map commands are missing the cisco keyword at the end.

A single router interface cannot connect to more than one Frame Relay peer at a time.

45. Which IP address and wildcard mask would be used in an ACL to block traffic from all hosts on thesame subnet as host 192.168.16.43/28?

access-list 10 deny 192.168.16.0 0.0.0.31

access-list 10 deny 192.168.16.16 0.0.0.31

access-list 10 deny 192.168.16.32 0.0.0.16

access-list 10 deny 192.168.16.32 0.0.0.15

access-list 10 deny 192.168.16.43 0.0.0.16

46. Which combination of Layer 2 protocol and authentication should be used to establish a link withoutsending authentication information in plain text between a Cisco and a non-Cisco router?

PPP with PAP

PPP with CHAP

HDLC with PAP

HDLC with CHAP

47. When would the multipoint keyword be used in Frame Relay PVCs configuration?

when global DLCIs are in use

when using physical interfaces

when multicasts must be supported

when participating routers are in the same subnet

48. A network technician analyzes the network and notices late collisions. The collisions occuraccompanied by jabber that originates from the server. What is the likely cause of the problem?

faulty switch port

web server CPU overload

faulty NIC in the web server

misconfiguration of web server services

49.

Refer to the exhibit. R1 is performing NAT overload for the 10.1.1.0/24 inside network. Host A has sent apacket to the web server. What is the destination IP address of the return packet from the web server?



Ma7moud

Pencil

Ma7moud

Pencil



10.1.1.2:1234

172.30.20.1:1234

172.30.20.1:3333

192.168.1.2:80

50.

Refer to the exhibit. All devices are configured as shown in the exhibit. PC1 is unable to ping the defaultgateway. What is the cause of the problem?

The default gateway is in the wrong subnet.

STP has blocked the port that PC1 is connected to.

Port Fa0/2 on S2 is assigned to the wrong VLAN.

S2 has the wrong IP address assigned to the VLAN30 interface.

51. When Frame Relay encapsulation is used, what feature provides flow control and exchangesinformation about the status of virtual circuits?

LCP

LMI

DLCI

Inverse ARP

52. A network administrator is tasked with maintaining two remote locations in the same city. Bothlocations use the same service provider and have the same service plan for DSL service. Whencomparing download rates, it is noticed that the location on the East side of town has a faster downloadrate than the location on the West side of town. How can this be explained?

The West side has a high volume of POTS traffic.

The West side of town is downloading larger packets.

The service provider is closer to the location on the East side.

More clients share a connection to the DSLAM on the West side.

Tag:Which configuration on the vty lines provides the best security measure for network administrators to remotelyaccess the core routers at headquarters?,Refer to the exhibit Headquarters is connected through the Internet tobranch office A and branch office B Which WAN technology would be best suited to provide secure connectivitybetween headquarters and both branch offices?,A network technician analyzes the network and notices latecollisions The collisions occur accompanied by jabber that originates from the server What is the likely cause ofthe problem?,Refer to the exhibit From the output of the show interfaces and ping commands at which layer ofthe OSI model is a fault indicated?,ccna 4 v4 0 final exam 2011,ccna 4 Final v4 0,Refer to the exhibit Based onthe output as shown which two statements correctly define how the router will treat Telnet traffic that comes intointerface FastEthernet 0/1,Which IP address and wildcard mask would be used in an ACL to block traffic from allhosts on the same subnet as host 192 168 16 43/28?,referral to the exhibit Which subnet mask will place allhosts on Network B in the same subnet with the least amount of wasted addresses,Which three physicalnetwork problems should be checked when a bottom-up troubleshooting approach has been chosen totroubleshoot network performance? (Choose three,A network administrator configures a standard access controllist on Router1 to prohibit traffic from the 192 168 0 0/24 network from reaching,Refer exhibit networkadministrator configuring username password SSH connection checking configuration administrator noticespassword displayed plain text configuration method used,R1 is performing NAT overload for the 10 1 1 0/24inside network Host A has sent a packet to the web server What is the source IP address of the return packetfrom the web server when received at the NIC on host A?,ccna4 v4 0 final answers,CCNA2 - Final ExamAnswers V4 0,ccna-4-final-exam-v4-0-answers html,ccna v4 0 final exam,While troubleshooting a problem withan e-mail server an administrator observes that the switch port used by the server shows up line protocol up Theadministrator cannot ping the server At which layer of the OSI model is the problem most likely to be fou





Posted by admin at 3:39 pm Tagged with: Accessing the WAN Final Exam Answers, CCNA 4, CCNA 4 Exam Final,CCNA 4 Final Exam Answers, CCNA 4 Final Exam V4.0 Answers 2010, CCNA 4 Final

Exams, CCNA 4 Final Test, CCNA 4 Practice Final Exam Answers, CCNA Accessing TheWAN Final Exam Answers V4.0, CCNA Exploration 4 Final Exam Answers, CCNA Final,CCNA Final 4, CCNA Final Exam 4, CCNA Semester 4 Final Exam, Cisco CCNA 4 Final

Exam Answers, EWAN v4.0 Final, Final CCNA 4, LAN Switching and Wireless Final ExamAnswers

No Responses to “CCNA 4 Final Exam V4.0 Answers”

Nguyen tran says:

January 19, 2011 at 8:29 am

Thank admin!3 questions not here.I have send it to your email

Reply

1.

Frank says:


Question 13 is wrong.should be these two:They begin with the FE80::/10 prefix.

They are assigned by IANA to an organization.

Reply

admin says:


Thanks! Updated

Reply

2.

Frank says:


question 45 is wrong:

answer should be:

access-list 10 deny 192.168.16.32 0.0.0.15its with the wildcard .15 Not .16 ….

The answer for 11 be “The mapping between DLCI 100 and 172.16.3.1 was learned through Inverse ARP”

Reply

admin says:


Thank you very much.

Reply

admin says:


Updated! Now all answers are correct

Reply

3.

anak indo says:

January 19, 2011 at 1:55 pm

i have a ccna exam tomorrow, is it the valid one???

Reply

4.

admin says:

January 22, 2011 at 11:01 am

5.





anak indo:

i have a ccna exam tomorrow, is it the valid one???

yes

Reply

The WTO blogger says:


Question 13 is wrong. The have the fe80::/10 prefix and are configured automatically

Reply

6.

The WTO blogger says:


Also, the last one should be More clients share a connection to the DSLAM on the West side.

Reply

7.

Jay says:


Is this the real ccna exam bc I have an exam on Friday?

Reply

8.

Babbe says:


question 8 should be“detect potential attacks”

Reply

admin says:


Thank you

Reply

9.

benny says:

February 21, 2011 at 2:20 am

16 is wrong

should be

Use quotes or phrases to create pass phrases.

Disable the HTTP server service.48 is wrongfaulty NIC in the web server is the right answer

Reply

admin says:

February 21, 2011 at 4:35 am

Thank you!

Reply

10.





© 2011 CCNA FINAL Suffusion theme by Sayontan Sinha

Name

E-mail

URI

Leave a Reply

(required)

(required)

Your Comment

You may use these HTML tags and attributes: <a href="" title=""> <abbr title=""> <acronym title=""> <b><blockquote cite=""> <cite> <code> <del datetime=""> <em> <i> <q cite=""> <strike> <strong>

Submit Comment





3- final exam v4.0 answers 8 jan 2011

Documents