3 nomenclature and options - sew eurodrive.../fk x flange-mounted motor (deviating from iec) with...

3 Nomenclature and options Gear options

Catalog – DRS/DRN.. Gearmotors

2193

3480

/EN

-US

– 0

4/20

18

22

3 Nomenclature and options

3.1 Gear options

3.1.1 Helical gear units Error! B ookmark not d efined .Error! Boo kmark not defin ed .

Nomenclature Description

RX.. Foot-mounted with 1 gearing stage

RXF.. B5 flange with 1 gearing stage

R.. Foot-mounted

R..F Foot-mounted with B5 flange

RF.. B5 flange

RZ.. B14 flange (tapped holes) with solid shaft

RM.. B5 flange with extended bearing hub

3.1.2 theSnuggler helical gear units Error! B ookmark not d efined .Error! Boo kmark not defin ed .


F.. Foot-mounted (tapped holes) with solid shaft

FA..B Foot-mounted (tapped holes) with keyed hollow shaft

FH..B Foot-mounted (tapped holes) w/keyless hollow shaft and shrink disk

FV..B Foot-mounted (tapped holes) with DIN 5480 splined hollow shaft

FF.. B5 flange with solid shaft

FAF.. B5 flange with keyed hollow shaft

FHF.. B5 flange with keyless hollow shaft and shrink disk

FVF.. B5 flange with DIN 5480 splined hollow shaft

FTF.. B5 flange with keyless hollow shaft and TorqLOC® taper bushing

FA.. Keyed hollow shaft

FH.. Keyless hollow shaft with shrink disk

FT.. Keyless hollow shaft with TorqLOC® taper bushing system

FV.. DIN 5480 splined hollow shaft

FZ.. B14 flange (tapped holes) and solid shaft

FAZ.. B14 flange (tapped holes) and keyed hollow shaft

FHZ.. B14 flange (tapped holes) and keyless hollow shaft w/shrink disk

FVZ.. B14 flange (tapped holes) and DIN 5480 splined hollow shaft

3 Nomenclature and optionsGear options

3

Catalog – DRS/DRN.. Gearmotors 23

2193

3480

/EN

-US

– 0

4/20

18

3.1.3 Helical-bevel gear units Error! B ookmark not d efined .Error! Boo kmark not defin ed .


K.. Foot-mounted with solid shaft

KA..B Foot-mounted with keyed hollow shaft

KH..B Foot-mounted with keyless hollow shaft and shrink disk

KV..B Foot-mounted with DIN 5480 splined hollow shaft

KF.. B5 flange with solid shaft

KAF.. B5 flange with keyed hollow shaft

KHF.. B5 flange with keyless hollow shaft and shrink disk

KTF.. B5 flange with keyless hollow shaft and TorqLOC® taper bushing system

KVF.. B5 flange with DIN 5480 splined hollow shaft

KA.. Keyed hollow shaft

KH.. Keyless hollow shaft with shrink disk

KT.. Keyless hollow shaft with TorqLOC® taper bushing system

KV.. DIN 5480 splined hollow shaft

KZ.. B14 flange (tapped holes) with solid shaft

KAZ.. B14 flange (tapped holes) with keyed hollow shaft

KHZ.. B14 flange (tapped holes) w/keyless hollow shaft and shrink disk

KVZ.. B14 flange (tapped holes) with DIN 5480 splined hollow shaft

3.1.4 Helical-worm gear units Error! B ookmark not d efined .Error! Boo kmark not defin ed .


S.. Foot-mounted with solid shaft

SF.. B5 flange with solid shaft

SAF.. B5 flange with keyed hollow shaft

SHF.. B5 flange with keyless hollow shaft and shrink disk

SA.. Keyed hollow shaft

SH.. Keyless hollow shaft with shrink disk

ST.. Keyless hollow shaft with TorqLOC® taper bushing system

SAZ.. B14 flange (tapped holes) with keyed hollow shaft

STF.. B5 flange with keyless hollowshaft and TorqLOC® taper bushing system

SHZ.. B14 flange (tapped holes) w/keyless hollow shaft and shrink disk

3 Nomenclature and options Gear options


2193

3480

/EN

-US

– 0

4/20

18

24

3.1.5 SPIROPLAN® gear units


W.. Foot-mounted with solid shaft

WF.. B5 flange with solid shaft

WAF.. B5 flange with keyed hollow shaft

WA.. Keyed hollow shaft

WA..B Foot-mounted with keyed hollow shaft

WH..B Foot-mounted with keyless hollow shaft and shrink disk

WHF.. B5 flange with keyless hollow shaft and shrink disk

WH.. Keyless hollow shaft with shrink disk

WT.. Keyless hollow shaft with TorqLOC® taper bushing system

3.1.6 Miscellaneous Options Error! B ookmark not d efined .Error! Boo kmark not defin ed .

Nomenclature Description R F K S W

/R Reduced backlash X X X - -

/T With torque arm - 1) X X X

/G With rubber buffers (to provide cushioning of torque arm)

- X - - -

1) F-series has built-in torque arm so optional torque arm is unnecessary

3.1.7 Condition monitoring Error! B ookmark not d efined .


/DUO Diagnostic Unit Oil = Oil aging sensor

3 Nomenclature and optionsMotor options

3


2193

3480

/EN

-US

– 0

4/20

18

3.2 Motor options

3.2.1 Size designation Error! B ookmark not d efined .

Nomenclature HazLoc-

NA Description

DRN.. - Energy-efficient motors of energy efficiency class IE3

EDRN.. X Motor for hazardous locations, 60Hz, energy efficiency class IE3

80 – 315 X Sizes: 80 / 90 / 100 / 112 / 132 / 160 / 180 / 200 / 225 / 250 / 280 / 315

S, M, MS, ME, LS, L, H

X

Lengths:

S = Short; M = Medium; L = Long; H = Extra-long design

MS = shorter variation of length M; ME = longer variation of length M

LS = Length S with shorter package

2 - Number of poles:

(2=3600 rpm, 4=1800 rpm, 6=1200 rpm) 4 X

6 -

3.2.2 Mounting types Error! B ookmark not d efined .


NA Description Size

/FI X IEC foot-mounted motor 80M – 315H

/F.A, /F.B X Universal foot-mounted motor 80M – 132S

225S – 315H

/FG X 7 series integral motor, as stand-alone motor 80M – 315H

/FF X IEC flange-mounted motor with bore 80M – 315H

/FT X IEC flange-mounted motor with threads 80M – 100L

/FL X Flange mounted motor (deviating from IEC) 80M – 315H

/FM X 7-series integral motor with IEC feet 80M – 315H

/FE X IEC flange-mounted motor with bore and IEC feet 80M – 315H

/FY X IEC flange-mounted motor with threads and IEC feet 80M – 100L

/FK X Flange-mounted motor (deviating from IEC) with feet 80M – 280M

/FC X C-face motor; flange and shaft dimensions in inch 71S – 160L (56C – 256TC)

3 Nomenclature and options Motor options


2193

3480

/EN

-US

– 0

4/20

18

26

3.2.3 Mechanical attachments Error! B ookmark not d efined .


NA Description Size

/BE.. X Spring-loaded brake with size designation 80M – 315H

/HR X Manual brake release (hand lever), with automatic re-engaging

80M – 315H

/HF X Manual brake release (screw), lockable 80M – 315H

/RS X Backstop 80M – 315H

/MSW - MOVI-SWITCH® 80M – 100L

/MI - Motor identification module for MOVIMOT® 80M – 112M

/MM03 – MM40 - MOVIMOT® 80M – 112M

/MO - MOVIMOT® option(s) 80M – 112M

3.2.4 Connectors Error! B ookmark not d efined .Error! Boo kmark not defin ed .


NA Description Size

/IS - Integrated plug connector 80M – 132S

/ASE. - HAN 10ES plug connector on terminal box with single locking latch (cage clamp contacts on the motor side)

80M – 132S

/ASB. - HAN 10ES plug connector on terminal box with double locking latch (cage clamp contacts on the motor side)

80M – 132S

/ACE. - HAN 10E plug connector on terminal box with single locking latch (crimp contacts on the motor side)

80M – 132S

/ACB. - HAN 10E plug connector on terminal box with double locking latch (crimp contacts on the motor side)

80M – 132S

/AME. -

HAN Modular 10B plug connector on terminal box with single locking latch (crimp contacts on the motor side)

80M – 132S

/ABE. - 80M – 225M

/ADE. - 80M – 225M

/AKE. - 132M – 225M

/AMB. -

HAN Modular 10B plug connector on terminal box with double locking latch (crimp contacts on the motor side)

80M – 132S

/ABB. - 80M – 225M

/ADB. - 80M – 225M

/AKB. - 132M – 225M

/AND. - Harting Han® Q8/0, single locking latch 80M – 132S

/AFQ. - Round plug connector Molex/Amphenol, 4-pole power 1 3/8" (AFQ8 housing Al), 3-pole brake connection 7/8", 3 fixed ends, max. 25 A, BG/BGE/BSR/BUR brake

80M – 132S


3


2193

3480

/EN

-US

– 0

4/20

18


NA Description Size

/AFL. - Round plug connector Molex/Amphenol, 4-pole power 7/8" (AFL8 housing Al), 3-pole brake connection 7/8", 3 ends, max. 25 A, BG/BGE/BSR/BUR brake

80M – 100L

/KCC X 6 or 10-pole terminal strip with cage clamp contacts 80M – 132S

/KC1 -

C1-profile-compliant connection of the electrified monorail system drive (VDI guideline 3643) (for DR71, 80). Alternatively for DR.90 – 132 for a more compact connection range

80M – 132S

/IV - Other industrial plug connectors according to customer specifications

80M – 225M

3.2.5 Hazardous location options Error! B ookmark not d efined .


NA Description

/CID2 X Motors suitable for use in Class I, Division 2, Groups A, B, C & D Gas atmosphere

/CIID2 X Motors suitable for use in Class II, Division 2, Groups F&G

Dust atmosphere

/CICIID2 X Motors suitable for use in Class I, Division 2, Groups A, B, C & D + Class II, Division 2, Groups F&G; gas or dust atmosphere

3.2.6 Temperature sensor Error! B ookmark not d efined .Error! Boo kmark not defin ed .


NA Description Size

/TF X Temperature sensor (PTC thermistor or PTC resistor) 80M – 315H

/TH - Thermostat (bimetallic switch) 80M – 315H

/PT X 1 or 3 PT100 sensor(s) 80M – 315H

/PK X 1 or 3 PT1000 sensor(s) 80M – 315H

3 Nomenclature and options Motor options


2193

3480

/EN

-US

– 0

4/20

18

28

3.2.7 Encoders Error! B ookmark not d efined .Error! Boo kmark not defin ed .


NA Description Size

/ES7S1) -

Add-on speed sensor with Sin/Cos interface

80M – 132S

/EG7S1) - 132M – 280M

/EV7S - 80M – 280M

/EH7S - 315S – 315H

/ES7R -

Add-on speed sensor with TTL (RS-422) interface,

V = 9 – 26 V

80M – 132S

/EG7R - 132M – 280M

/EV7R - 80M – 280M

/EH7R - 315S – 315H

/EI7C1) - Built-in incremental encoder w/HTL interface, 24 PPR 80M – 132S

/EI76 -

Built-in incremental encoder with HTL interface and 6 / 2 / 1 PPR (pulses per revolution)

80M – 132S

/EI72 - 80M – 132S

/EI71 - 80M – 132S

/AS7W1) -

Add-on absolute encoder, RS-485 interface (multi-turn)

80M – 132S

/AG7W1) - 132M – 280M

/AV7W - 80M – 280M

/AS7Y1) -

Add-on absolute encoder, SSI interface (multi-turn)

80M – 132S

/AG7Y1) - 132M – 280M

/AV7Y - 80M – 280M

/AH7Y - 315S – 315H

/ES7A -

Mounting adapter only. Used to mount speed sensors from the SEW-EURODRIVE portfolio

80M – 132S

/EG7A - 132M – 280M

/EV7A - 80M – 280M

/EH7A - 315S – 315H

/ES7C -

Add-on speed sensor with HTL interface

80M – 132S

/EG7C - 132M – 280M

/EV7C - 80M – 280M

/EH7C - 315S – 315H

/EH7T - Add-on speed sensor with TTL(RS422) interface 315S – 315H

/XV.A, XC.A X Mounting adapter only. Used for non-SEW sensors 80M – 280M

/XH1. - Mounted non-SEW speed sensor

80M – 132S2)

/XV.. - 80M – 280M

1) also available in safety-rated design 2) in preparation


3


2193

3480

/EN

-US

– 0

4/20

18

3.2.8 Ventilation Error! B ookmark not d efined .


NA Description Size

/V - Forced cooling fan 80M – 315H

/Z - High-inertia cast iron fan (flywheel fan) 80M – 132L

/AL X Metal fan (cold environments) 80M – 315H

/U - Non-ventilated (without fan) 80M – 315H

/OL - Non-ventilated (closed B-side) 80M – 132S

/C X Canopy attached to fan guard (M4 mounting) 80M – 315H

/LN X Low-noise fan guard 71, 100 – 132S

3.2.9 Motor Bearings Error! B ookmark not d efined .


NA Description Size

/NS X Grease nipples provided for lubrication 225S – 315H

/ERF X Reinforced bearings on A-side with rolling bearing 250M – 315H

/NIB X Insulated bearing B-side 200L – 315H

3.2.10 Condition monitoring Error! B ookmark not d efined .


NA Description Size

/DUE - Diagnostic Unit Eddy Current = function/wear monitoring for BE1 – BE122 brake

80M – 315H

3.2.11 Other additional features Error! B ookmark not d efined .


NA Description Size

/DH - Condensation drain hole 80M – 315H

/RI X Reinforced winding insulation 80M – 315H

/RI2 - Reinforced winding insulation with increased resistance against partial discharge

112M – 315H

/2W X 2nd shaft end on the motor/brakemotor 80M – 315H

3 Nomenclature and options Model type example


2193

3480

/EN

-US

– 0

4/20

18

30

3.3 Model type example Error! B ookmark not d efined .

The model type shown on the nameplate of the gearmotor is a combination of gear and motor components represented as letters and numbers, beginning at the output shaft. The following is an example of a compound helical-bevel gearmotor.

Example: K107R77DRN90L4 /TF

Gear unit series K Gear unit - large

Gear unit size 107

Gear unit series R Gear unit - small

Gear unit size 77

Motor series DRN..

Motor Motor size 90

Length L

Number of poles 4

Motor option temperature sensor

/TF Motor Option

9007212622923531

3.4 Serial number example Error! B ookmark not d efined .

Example: 87.74178600 01. 0001. 17. 60

87. Sales organization / Country code

74178600 Order number (8 digits)

01. Order line item

0001. Specific unit ID (within batch of identical gearmotors)

17. Year of manufacturing

60 Assembly facility (10=Lyman, SC; 50=Troy, OH; 60=Hayward, CA; 80=Dallas, TX; 90=Bridgeport, NJ)

K107 R77 DRN90L4/TF

3 Nomenclature and optionsNameplate example

3


2193

3480

/EN

-US

– 0

4/20

18

3.5 Nameplate example The following is an example of a USA nameplate on a DRN.. gearmotor.

Nameplate_US

[1] Model Type

[2] Serial number

[3] Frequency Motor speed / Output speed of gearmotor

[4] Motor rated power (HP) / Duty type

[5] Duty Type Power factor

[6] Thermal class NEMA design

[7] Constant torque speed range

[8] Ratio Output torque

[9] Oil type / volume (liters) based upon mounting position

[10] Weight (lbs) Ambient temperature

[11] Suitability for inverter operation Number of phases and performance standard

[12] Nominal voltage and connection type

[13] Full load amps Efficiency and energy efficiency class

[14] Motor service factor according to NEMA Degree of protection according to IEC 60034-12 Motor enclosure type

[15] KVA code according to NEMA MG1

[16] Manufacturing location: 85=Troy, OH; 86=Hayward, CA; 87=Lyman, SC; 88=Dallas, TX; 89=Bridgeport, NJ

[17] Nominal brake voltage

[18] Braking torque

[19] Brake control rectifier

[20] Mounting position

K47 DRN90L4/BE2HR87.7417860001.0001.17.60

SEW-EURODRIVE INC, USA

Hz 60 rpm 1767/60hp 2.0 S1Duty Cont. S1 P.F. 0.7

Th.Cl. 155 (F) Design NEMA ACT 300-1800 rpm

i 29.32 lb-in 2120 MtgPos M1BCLP220 Miner.Oil/ 0.8 l

lb 101.014 AMB °C -20..40 188 573 1EN

Inverter duty VPWM 3ph.IEC60034V 230/460 YY/YA 6.0/3.0 Nom.Eff% 86.5 IE3

S.F. 1.15 IP 54 TEFCK.V.A-Code M

ML 86

C USMC

1706

02

EnergyVerified

E189357 CC056ACC056A

Vbr 230 AC

lb-in 177BG1.5

[11][12][13][14][15][16][17][18][19][20]

[1][2][3][4][5][6][7]

[8][9]

[10]

3 Nomenclature and options Gearmotor types


2193

3480

/EN

-US

– 0

4/20

18

32

3.6 Gearmotor types

INFORMATION

The options described in this chapter refer to gearmotors available from SEW-EURODRIVE. They also apply to gear units without motors.

3.6.1 Helical gearmotors Error! B ookmark not d efined .

RX..DR..

Helical gearmotor (single stage), foot-mounted

RXF..DR..

Single-stage helical gearmotor with B5 flange

R..DR..

Helical gearmotor, foot-mounted

R..F DR..

Helical gearmotor foot-mounted with B5 flange

RF..DR..

Helical gearmotor with B5 flange

RZ..DR..

Helical gearmotor with B14 flange

RM..DR..

Helical gearmotor with B5 flange and extended bearing hub

3 Nomenclature and optionsGearmotor types

3


2193

3480

/EN

-US

– 0

4/20

18

3.6.2 theSnuggler helical gearmotors Error! B ookmark not d efined .Error! Boo kmark not defin ed .

F..DR.. theSnuggler helical gearmotor with solid shaft and tapped rail holes for foot mounting

FA..B DR.. theSnuggler helical gearmotor with keyed hollow shaft and tapped rail holes for foot mounting

FV..B DR.. theSnuggler helical gearmotor with DIN 5480 splined hollow shaft and tapped rail holes for foot mounting

FH..B DR.. theSnuggler helical gearmotor with keyless hollow shaft, shrink disk, and tapped rail holes for foot mounting

FF..DR.. theSnuggler helical gearmotor with B5 flange and solid shaft

FAF..DR.. theSnuggler helical gearmotor with B5 flange and keyed hollow shaft

FVF..DR.. theSnuggler helical gearmotor with B5 flange and DIN 5480 splined hollow shaft



2193

3480

/EN

-US

– 0

4/20

18

34

FHF..DR.. theSnuggler helical gearmotor with B5 flange and keyless hollow shaft with shrink disk

FA..DR.. theSnuggler helical gearmotor with keyed hollow shaft

FV..DR.. theSnuggler helical gearmotor with DIN 5480 splined hollow shaft

FH..DR.. theSnuggler helical gearmotor with keyless hollow shaft and shrink disk

FT..DR.. theSnuggler helical gearmotor with keyless hollow shaft and TorqLOC® tapered bushing system

FZ..DR.. theSnuggler helical gearmotor with B14 flange (tapped holes) and solid shaft

FAZ..DR.. theSnuggler helical gearmotor with B14 flange (tapped holes) and keyed hollow shaft

FVZ..DR.. theSnuggler helical gearmotor with B14 flange (tapped holes) and DIN 5480 splined hollow shaft

FHZ..DR.. theSnuggler helical gearmotor with B14 flange (tapped holes) and keyless hollow shaft with shrink disk


3


2193

3480

/EN

-US

– 0

4/20

18

3.6.3 Helical-bevel gearmotors sizes K..19 and K..29 Error! B ookmark not d efined .Error! Boo kmark not defin ed .

K19 DR.., K29 DR..

Helical-bevel gearmotor, foot-mounted with solid shaft

KA19B DR.., KA29B DR..

Helical-bevel gearmotor, foot-mounted with keyed hollow shaft

KH19B DR.., KH29B DR..

Helical-bevel gearmotor, foot-mounted with keyless hollow shaft and shrink disk

KF19B DR.., KF29B DR..

Helical-bevel gearmotor, foot-mounted with B5 flange and solid shaft

KAF19B DR.., KAF29B DR..

Helical-bevel gearmotor, foot-mounted with B5 flange and keyed hollow shaft

KHF19B DR.., KHF29B DR..

Helical-bevel gearmotor, foot-mounted with B5 flange, keyless hollow shaft and shrink disk

KF19 DR.., KF29 DR..

Helical-bevel gearmotor with B5 flange and solid shaft

KA19 DR.., KA29 DR..

Helical-bevel gearmotor with keyed hollow shaft



2193

3480

/EN

-US

– 0

4/20

18

36

KAF19 DR.., KAF29 DR..

Helical-bevel gearmotor with B5 flange and keyed hollow shaft

KH19 DR.., KH29 DR..

Helical-bevel gearmotor with keyless hollow shaft and shrink disk

KHF19 DR.., KHF29 DR..

Helical-bevel gearmotor with B5 flange and keyless hollow shaft with shrink disk

3.6.4 Helical-bevel gearmotors, sizes K..39 and K..49 Error! B ookmark not d efined .Error! Boo kmark not defin ed .

K39 DR.., K49 DR..


KF39 DR.., KF49 DR..


KA39 DR.., KA49 DR..


KAF39 DR.., KAF49 DR..


KT39 DR.., KT49 DR..

Helical-bevel gearmotor with keyless hollow shaft and TorqLOC® taper bushing system


3


2193

3480

/EN

-US

– 0

4/20

18

3.6.5 Helical-bevel gearmotors, sizes K..7 Error! B ookmark not d efined .Error! Boo kmark not defin ed .

:

K..7 DR..


KA..7B DR..

Helical-bevel gearmotor, foot-mounted with keyed hollow shaft

KV..7B DR..

Helical-bevel gearmotor, foot-mounted with DIN 5480 splined hollow shaft

KH..7B DR..

Helical-bevel gearmotor, foot-mounted with keyless hollow shaft and shrink disk

KF..7 DR..


KAF..7 DR..


KVF..7 DR..

Helical-bevel gearmotor with B5 flange and DIN 5480 splined hollow shaft

KHF..7 DR..

Helical-bevel gearmotor with B5 flange with keyless hollow shaft and shrink disk

KA..7 DR..


KV..7 DR..

Helical-bevel gearmotor with DIN 5480 splined hollow shaft



2193

3480

/EN

-US

– 0

4/20

18

38

KH..7 DR..

Helical-bevel gearmotor with keyless hollow shaft and shrink disk

KT..7 DR..

Helical-bevel gearmotor with keyless hollow shaft and TorqLOC® tapered bushing system

KZ..7 DR..

Helical-bevel gearmotor with B14 flange (tapped holes)

KAZ..7 DR..

Helical-bevel gearmotor with B14 flange (tapped holes) and keyed hollow shaft

KVZ..7 DR..

Helical-bevel gearmotor with B14 flange (tapped holes) with DIN 5480 splined hollow shaft

KHZ..7 DR..

Helical-bevel gearmotor with B14 flange (tapped holes) with keyless hollow shaft and shrink disk


3


2193

3480

/EN

-US

– 0

4/20

18

3.6.6 Helical-worm gearmotors Error! B ookmark not d efined .Error! Boo kmark not defin ed .

S..DR..

Helical-worm gearmotor, foot-mounted with solid shaft

SF..DR..

Helical-worm gearmotor with B5 flange and solid shaft

SAF..DR..

Helical-worm gearmotor with B5 flange and keyed hollow shaft

SHF..DR..

Helical-worm gearmotor with B5 flange and keyless hollow shaft with shrink disk

SA..DR..

Helical-worm gearmotor with keyed hollow shaft

SH..DR..

Helical-worm gearmotor with keyless hollow shaft and shrink disk

ST..DR..

Helical-worm gearmotor with keyless hollow shaft and TorqLOC® taper bushing system



2193

3480

/EN

-US

– 0

4/20

18

40

SAZ..DR..

Helical-worm gearmotor with B14 flange (tapped holes) and keyed hollow shaft

SHZ..DR..

Helical-worm gearmotor with B14 flange and keyless hollow shaft with shrink disk

3.6.7 SPIROPLAN® gearmotors, sizes W..10, W..20, W..30

W10 DR.., W20 DR.., W30 DR..,

SPIROPLAN® gearmotor, foot-mounted with solid shaft

WF10 DR.., WF20 DR.., WF30 DR..

SPIROPLAN® gearmotor with B5 flange and solid shaft

WA10 DR.., WA20 DR.., WA30 DR..

SPIROPLAN® gearmotor with keyed hollow shaft

WAF10 DR.., WAF20 DR.., WAF30 DR..

SPIROPLAN® gearmotor with B5 flange and keyed hollow shaft


3


2193

3480

/EN

-US

– 0

4/20

18

3.6.8 SPIROPLAN® gearmotors, sizes W..37 and W..47

W37 DR.., W47 DR..

SPIROPLAN® gearmotor, foot-mounted with solid shaft

WA37B DR.., WA47B DR..

SPIROPLAN® gearmotor, foot-mounted with keyed hollow shaft

WH37B DR.., WH47B DR..

SPIROPLAN® gearmotor, foot-mounted with keyless hollow shaft and shrink disk

WF37 DR.., WF47 DR..

SPIROPLAN® gearmotor with B5 flange and solid shaft

WAF37 DR.., WAF47 DR..

SPIROPLAN® gearmotor with B5 flange and keyed hollow shaft

WHF37 DR.., WHF47 DR..

SPIROPLAN® gearmotor with B5 flange and keyless hollow shaft with shrink disk

WA37 DR.., WA47 DR..

SPIROPLAN® gearmotor with keyed hollow shaft

WH37 DR.., WH47 DR..

SPIROPLAN® gearmotor with keyless hollow shaft and shrink disk

WT37 DR.., WT47 DR..

SPIROPLAN® gearmotor with keyless hollow shaft and TorqLOC® tapered bushing system

3 nomenclature and options - sew eurodrive.../fk x flange-mounted motor (deviating from iec) with...

Documents