3.0l engine—mil on—dtc p0301 and/or tsb 11-4-16 …tsb 11-4-16 (continued) 3. replace the right...
TRANSCRIPT
3.0L ENGINE—MIL ON—DTC P0301 AND/OR TSB 11-4-16MISFIRE/RUNS ROUGH—ENGINE BUILD DATES12/21/2010 TO 1/7/2011
FORD: MERCURY:2011 Fusion, Escape 2011 Milan, Mariner
ISSUESome 2011 Escape, Mariner, Fusion, and Milan
vehicles equipped with a 3.0L engine and an engine
build date of 12/21/2010 to 1/7/2011 may exhibit a
misfire or runs rough condition, or malfunction
indicator lamp (MIL) on with diagnostic trouble code
(DTC) P0301.
ACTIONFollow the Service Procedure steps to correct the
condition.
SERVICE PROCEDURE
1. Determine engine build date. Refer toFigure 1 - Article 11-4-16
Workshop Manual (WSM), Section 303-01. Is
the engine build date 12/21/2010 to 1/7/2011?
a. Yes - engine build date is 12/21/2010 to
1/7/2011, proceed to Step 2.
b. No - engine build date is not 12/21/2010 to
1/7/2011; do not continue with this article.
Refer to the Powertrain Control/Emissions
Diagnosis (PC/ED) manual for normal
diagnostics.
2. Determine right hand cylinder head
manufacturing time and date. Inkjet stamp is
located on the intake face of the RH cylinder
head under the upper intake manifold and can
be viewed by looking over the front engine Figure 2 - Article 11-4-16
mount. Stamp will read FFV80 HH:MMa. Yes - Right hand cylinder headMMDDYY. (Figures 1 and 2) Does right hand
manufacturing time and date stampcylinder head time and date stamp indicateindicates 14:30 12/21/2010 to 14:0014:30 12/21/2010 to 14:00 1/7/2011?1/7/2011, proceed to Step 3.
b. No - Right Hand cylinder head
manufacturing time and date stamp does
not indicate 14:30 12/21/2010 to 14:00
1/7/2011, do not continue with this article.
Refer to PC/ED manual for normal
diagnostics.
NOTE: The information in Technical Service Bulletins is intended for use by trained, professional technicians with the knowledge, tools, and equipment to dothe job properly and safely. It informs these technicians of conditions that may occur on some vehicles, or provides information that could assist in propervehicle service. The procedures should not be performed by “do-it-yourselfers”. Do not assume that a condition described affects your car or truck. Contact aFord or Lincoln dealership to determine whether the Bulletin applies to your vehicle. Warranty Policy and Extended Service Plan documentation determineWarranty and/or Extended Service Plan coverage unless stated otherwise in the TSB article.The information in this Technical Service Bulletin (TSB) wascurrent at the time of printing. Ford Motor Company reserves the right to supercede this information with updates.The most recent information is availablethrough Ford Motor Company’s on-line technical resources.
Copyright 2011 Ford Motor Company Online Publication Date April 18, 2011 PAGE 1
TSB 11-4-16 (Continued)
3. Replace the right hand cylinder head. Refer toOPERATION DESCRIPTION TIME
WSM, Section 303-01.110416A 2011 Escape 3.0L DOHC: 8.5 Hrs.
Check DTCs, Inspect BuildPART NUMBER PART NAME
Dates, And Replace TheAL8Z-6049-A Cylinder Head - Right Hand RH Cylinder Head (Do Not4F1Z-6065-AB Head Bolt
Use With Any Other Labor9L8Z-6051-A Head Gasket- Right Hand
Operations)3M4Z-6020-AA Front Cover Gasket110416A 2011 Fusion And Milan 10.19L8Z-9H486-B Upper Intake Gasket
9L8Z-9439-A Lower Intake Gasket 3.0L DOHC: Check DTCs, Hrs.9L8Z-6584-B Cam Cover Gasket (Left Side) Inspect Build Dates, And9L8Z-6584-A Cam Cover Gasket (Right Hand)
Replace The RH CylinderXW4Z-9448-AD Exhaust Manifold Gasket
Head (Do Not Use With
Any Other Labor
WARRANTY STATUS: Eligible Under Provisions Of Operations)
New Vehicle Limited DEALER CODING
Warranty Coverage And CONDITION
Emissions Warranty BASIC PART NO. CODE
Coverage 6049 12
IMPORTANT: Warranty
coverage limits/policies are
not altered by a TSB.
Warranty coverage limits
are determined by the
identified causal part.
PAGE 2