32pc51

PLASMA TVSERVICE MANUAL

CAUTIONBEFORE SERVICING THE CHASSIS,READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : PP78C

MODEL : 32PC51 32PC51-ZB

website:http://biz.LGservice.com

Internal Use Only

- 2 - LGE Internal Use OnlyCopyright©2007 LG Electronics. Inc. All right reserved. Only for training and service purposes

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ..........................................................................3

SPECIFICATION ........................................................................................4

ADJUSTMENT INSTRUCTION .................................................................6

TROUBLE SHOOTING ............................................................................13

BLOCK DIAGRAM...................................................................................20

EXPLODED VIEW .................................................................................. 22

EXPLODED VIEW PARTS LIST ............................................................ 23

REPLACEMENT PARTS LIST ............................................................... 24

SVC. SHEET ...............................................................................................

PRINTED CIRCUIT DIAGRAM ....................................................................


SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in theSchematic Diagram and Replacement Parts List. It is essential that these special safety parts should be replaced with the same components as recommended in this manual to preventX-RADIATION, Shock, Fire, or other Hazards. Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during theservicing of a receiver whose chassis is not isolated from the ACpower line. Use a transformer of adequate power rating as thisprotects the technician from accidents resulting in personal injuryfrom electrical shocks.

It will also protect the receiver and it's components from beingdamaged by accidental shorts of the circuitry that may beinadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this monitor is blown, replace itwith the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor,over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Due to high vacuum and large surface area of picture tube,extreme care should be used in handling the Picture Tube.Do not lift the Picture tube by it's Neck.

Leakage Current Cold Check(Antenna Cold Check)With the instrument AC plug removed from AC source, connect anelectrical jumper across the two AC plug prongs. Place the ACswitch in the on position, connect one lead of ohm-meter to the ACplug prongs tied together and touch other ohm-meter lead in turn toeach exposed metallic parts such as antenna terminals, phonejacks, etc. If the exposed metallic part has a return path to the chassis, themeasured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis thereading must be infinite.An other abnormality exists that must be corrected before thereceiver is returned to the customer.

Leakage Current Hot Check (See below Figure) Plug the AC cord directly into the AC outlet.Do not use a line Isolation Transformer during this check. Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitorbetween a known good earth ground (Water Pipe, Conduit, etc.)and the exposed metallic parts.Measure the AC voltage across the resistor using AC voltmeterwith 1000 ohms/volt or more sensitivity.Reverse plug the AC cord into the AC outlet and repeat AC voltagemeasurements for each exposed metallic part. Any voltagemeasured must not exceed 0.75 volt RMS which is corresponds to0.5mA.In case any measurement is out of the limits specified, there ispossibility of shock hazard and the set must be checked andrepaired before it is returned to the customer.

Leakage Current Hot Check circuit

1.5 Kohm/10W

To Instrument'sexposed METALLIC PARTS

Good Earth Groundsuch as WATER PIPE,CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF


SPECIFICATIONSNOTE : Specifications and others are subject to change without notice for improvement.

V Application RangeThis spec is applied to the 32” PLASMA TV used PP78C Chassis.

V Specification

Each part is tested as below without special appointment.1) Temperature : 25±5°C (77±9°F), CST : 40±52) Relative Humidity: 65±10%3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz)

* Standard Voltage of each product is marked by models.4) Specification and performance of each parts are followed each drawing and specification by part number in accordance with SBOM.5) The receiver must be operated for about 20 minutes prior to the adjustment.

V Test Method1) Performance : LGE TV test method followed.2) Demanded other specification

Safety : CE, IEC specificationEMC : CE, IEC

V General Specification ( 32”WVGA )

Display Screen Device

Aspect Ratio

PDP Module

Operating Environment

Storage Environment

Input Voltage

1

2

3

4

5

6

No Item Specification Remark

32” Wide Color Display Module

16:9

PDP32F1,

RGB Closed Type

1)Temp. : 0~40deg

2)Humidity : 0~85%

3)Temp. : -20~60deg

4)Humidity : 0~85%

100-240V~, 50/60Hz

Plasma Display Panel

Glass Filter

LGE SPEC.

Maker : LG

Chassis

PP78C 32PC51-ZB EU LG

Model Name Market Brand Remark

32PC51-ZB Safety : IEC/EN60065,

EMI : EN55013,

EMS : EN55020

EU

Model ApplianceMarket

TEST

Remark


V General Specification2

Market

Broadcasting system

Available Channel

Receiving system

SCART Jack(2EA)

Component Input (1EA)

RGB Input(1EA)

HDMI Input(1EA)

Audio Input (4EA)

Audio variable out(1EA)

1

2

3

4

5

6

7

8

9

10

No Item Specification Remark

EU

PAL-BG/I/DK, SECAM

BAND PAL NTSC

VHF/UHF C1~C69 2~83

CATV S1~S47 1~71

Upper Heterodyne

PAL, SECAM, NTSC

Y/Cb/Cr, Y/Pb/Pr

RGB-PC

HDMI-DTV

PC Audio, Component(1EA),

Full SCART, Half SCART

HDMI PC spec out

L/R Input

Display area

Outline dimension

Number of Pixels

Cell pitch

Pixel type

Weight(net)

Weight(gross)

Operation Environment Temperature

Humidity

Pressure

Storage Environment Temperature

Humidity

Pressure

I mage stick minimization Start time

mode Low Brightness

Arrival Time

708.0.1(H) x 398.4(V) ± 0.5mm

790(H) x 466.5(V) x 59.1(D) ± 1mm

852(H) x 480(V)

831um(H) x 830um(V)

RGB closed type

7.55 8.05 8.55

118.5 123.5 128.5

0 ~ 40

20 ~ 80

800 ~ 1100

-20 ~ 60

10 ~ 90

700 ~ 1100

4.5 5 5.5

14 15 16

1

2

3

4

5

6

7

8

9

10

No Item Remark

1Pixel=3RGB Cells

1Pixel=3RGB Cells

12 1Box

Altitude : 0 to 2000M

Altitude : 0 to 3000M

mm

mm

um

Kg

Kg

deg

%

hPa

deg

%

hPa

min

min

Min Typ Max Unit

V Module Specification ( PDP32F1 )


ADJUSTMENT INSTRUCTION

1. Application ObjectThese instructions are applied all of the 32” PLASMA TV, PP78C Chassis.

2. Note(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolationtransformer will help protect test instrument.

(2) Adjustment must be done in the correct order.(3) The adjustment must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity ifthere is no specific designation.

(4) The input voltage of the receiver must keep 100-220V~,50/60Hz.

(5) Before adjustment, execute Heat Run for 30 minutes.

3. Adjustment items

3.1. PCB assembly adjustment items(1) Download the VCTP main software (IC500,VCT_Pro)(2) Color carrier Adjustment

3.2. SET assembly adjustment items(1) DDC Data input.(2) Adjustment of White Balance.(3) Factoring Option Data input.

4. PCB assembly adjustment method(Using VCTP Download program)

4-1. Download program installation(1) Extract a Zip file.

(2) Visual I2C & LPT Driver Installation.

LPT Port Driver (LptDrv) Setups : Program Files > Micronas >Visual I2C > Port_Driver

*Use for Windows 95/98 : Setup_LptDrv_v0104_9x.exe*Use for Windows 2000/XP : Setup_LptDrv_v0202_XP_2000.exe*Use for Windows NT : Setup_LptDrv_v0104_NT.exe

(3) Verification.(Start > Programs > Micronas > Visual I2C orLptDrv)

(4) LPT delay setting.(File > Preference > LPT preferences)

(5) Exchange the “bootloader.bat” file.

Install the LPT DriverInstall the Visual I2C

*LPT SETTING- Delay => 1- Time out => 500 ms

G Double click the Red area


G Select the "Bootloader.bat" file.(install > VCTP_download > Bootloader)

G Push "OK".

G Finish the program, after saving the file "download_cs.vi2c".(if you click , the massage appears automatically)

5. S/W program download

5-1. Download method 1 (PCB Ass’y)

(1) Connect the download jig to D-sub jack.(2) Execute ‘Download.vi2c’ program in PC, then a main

window will be opened.

(3) Double click the blue box and confirm "Bootloader Version" as 42.

(4) Click the "Erase Flash" button.

(5) Double click the download file low, then "edit" window willbe opened.

(6) Click the choice button in the “edit window”, then “filechoice window” will be opened.

(7) Choose the Hex file in folder and execute downloadingwith click " open" button.

(8) Click OK button at the "edit window".(9) Under Downloading process.

(10) If download is failed, for example "No acknowledge fromslave". Execute download again from(1).

x

Shortcut to download

Double click


5-2.Download method 2 (Set)(1) Push the “Tilt” button in an Adjust Remocon Then the

PLASMA TV will change a “slave mode”.

(2) Connect Zig to TV using a D-sub cable.

(3) Execute ‘Download_CS.vi2c’ program in PC, then a mainwidow will be opened.

(4) Click "GO" button.

If you don’t push the “go”, the Hex fi le would not bedownloaded although the download proceeds normally atfirst glance.

(5) Double click the blue box and confirm "Bootloader Version"as 42.

(6) Click the "Erase Flash" button.

(7) Double click the download file low then, "edit" window willbe opened.

(8) Chick the choice button I n the "edit window", then "filechoice window’ will be opened.

(9) Click the “load > flash” button.

(10) Click OK button at the "edit window".

(11) Under Downloading progress.

(12) If download is failed, for example "No acknowledge fromslave", execute download again from (1).

Shortcut todownload_cs

Double click


6. Tool Option Area Option Change6-1. Adjustment method

Before PCB check, have to change the Tool option and Area option.Option values are below.(If on changed the option, the input menu can differ the model spec.)The input methods are same as other chassises.(Use adj Keyon the Adjust Remocon)

7. Color carrier Adjustment(Inspection process)

(1) tuning the RF signalZB, TB/TD : PAL Philips Pattern (with Color Bar)

(2) push the “adj” key in the adjustment remocon.

8. EDID(The Extended Display Identification Data )

/DDC(Display Data Channel) download

8-1. EDID Data

<EDID Data Analog Set : 128Bytes >

<EDID Data HDMI1 Set : 256Bytes >

<EDID Data HDMI2 Set : 256Bytes >

=> Detail EDID Options are below([1],[2],[3],[4],[5])

1. [1]-Product ID

2. [2]-Serial No : Controlled on production line3. [3]-Month, Year : Controlled on production line

ex) Monthly: '03' => '03' Year: '2005' => '0F'

4. [4]-Model Name : model name -> LG TV- LG TV

5. [5]-Checksum (7EH) -> Changeable by total EDID data.

- Use the proper signal cable for EDID Download.- Never connect HDMI & D-SUB Cable at the same time.- Use the proper cables below for EDID Writ.

32(VGA)

Area Option

Tool Option ZB TB/TD

04164

Depend on PR

For RGB EDID For HDMI EDID

No

1

2

3

Item

Manufacturer ID

Version

Revision

Condition

GSM

Digital : 1

Digital : 2

Hex Data

1E6D

01

03

2D

Model

Name

32PC5R

32PC51

DEC

30168(A)

30169(D)

30176(A)

30177(D)

Product ID

HEX

75D8

75D9

75E0

75E1

EDID table

D875

D975

E075

E175

32PC5R 00 00 00 FD 00 3A 3F 1F 32 09 00 0A 20 20 20 20 20 20

Model Name Model Name(HEX)


8-2. Required Test Equipment(1) Adjusting PC with S/W for writing EDID Data.

(S/W : EDID TESTER Ver.2.5)(2) A Jig for EDID Download.(3) Cable : Serial(9Pin or USB) to D-sub 15Pin cable, D-sub

15Pin cable, DVI to HDMI cable.

8-3. Preparation for Adjustment(1) As above (Fig. 2), Connect the Set, EDID Download Jig,

PC & Cable.(2) Turn on the PC & EDID Download Jig. And Execute the

S/W : EDID TESTER Ver 2.5.(3) Set up S/W option.

Repeat Number : 5Device Address : A0PageByte : 8

(4) Power on the Set.

8-4. Sequence of Adjustment(1) DDC data of Analog-RGB

1) Init the data.

2) Load the EDID data.(Open File).

[ Analog-RGB : PP78C_RGB.ANA ][ Digital-HDMI1 : PP78C_HDMI1.DVI ][ Digital-HDMI2 : PP78C_HDMI2.DVI ]

3) Set the S/W as below.

4) Push the “Write Data & Verify”button. And confirm “Yes”.

5) If the writing is finished, you will see the “OK” message.

(Fig. 2) Connection Diagram of DDC download

Open FileOpen File


9. Adjustment of White Balance

9-1. Purpose and Principle for adjustmentof the color temperature

(1) Purpose : Adjust the color temperature to reduce thedeviation of the module color temperature.

(2) Principle : To adjust the white balance without thesaturation, Fix the one of R/G/B gain to 80 and decreasethe others.

9-2.Adjustment mode: Two modes of Cool and Warm.(Medium data is

automatically calibrated by the cool data)

9-3. Required Equipment(1) Remote control for adjustment.(2) Color Analyzer : CA-100+, CA210 or same product.

- Plasma TV(ch : 10)(3) Auto W/B adjustment instrument.(only for Auto adjustment)

9-4. Connecting diagram of equipment formeasuring (For Automatic Adjustment)

(1) Enter the DDC adjust mode.- Enter the white balance adjustment mode at the same

time heat-run mode when pushing the power on by poweronly key.

- Maintain the white balance adjustment mode with samecondition of Heat-run.

-> Maintain after AC off/on in status of Heat-run pattern display.(2) Release the DDC adjust mode.

- Release the adjust mode after AC off/on or std-by off/onin status of finishing the Hear-run mode.

- Release the Adjust mode when receiving the aging offcommand(F3 00 00) from adjustment equipment.

- Need to transmit the aging off command to TV set afterfinishing the adjustment.

* Standard color coordinate and temperature when using theCA-100+ or CA210 equipment.

* Synchronization relation between PSM and CSM.

(3) DDC adjustment support command set.

* R/G/B GAIN max value : 80

9-5. Adjustment of White Balance(For Manual adjustment)

- Adjustment mode : Two modes of Cool (Dynamic) andWarm(Mild).(Medium data is automatically calibrated by the cool data)

- Color analyzer(CA110, CA210) should be used in thecalibrated ch by CS-1000.(PDP : CH10)

- Operate the zero-calibration of the CA-110 or CA-210, thenstick sensor to the module when adjusting.

- For manual adjustment, it is also possible by the followingsequence.

(1) Select RF no signal by pressing “POWER ON” key onremote control for adjustment then operate heat run morethan 15 minutes.

(If not executed this step, the condition for W/B will be differ.)(2) Changing to the av mode by pushing the input or front av

key.(av mode : av1 or av2 or av3)(3) Display the internal pattern of the VCT-Pro IC by pushing

the IN-START.(4) Stick sensor to center of the screen and select each items

(Red/Green/Blue Gain and Offset) using D/E (CH+/-) keyon R/C.

(5) Adjust R Gain / B Gain using F/G (VOL+/-) key on R/C.(6) Adjust two modes of Cool(Dynamic) and Warm(Mild) as

below figure.(Fix the one of R/G/B and change the others)1. Push the one time the in-start key : Dynamic(Cool)2. Push the two more the in-start key : Mild(Warm)

Color Coordinate

x y

0.283±0.003

0.295±0.003

0.329±0.003

11,000K

9,300K

6,500K

0.000

0.000

0.003

0.276±0.003

0.283±0.003

0.313±0.003

COOL

MEDIUM

WARM

Mode Temp uv

CSM Remark

Cool

Normal

Warm

Dynamic

Standard

Mild

PSM

Adjustment

Aging On/Off

Input select

R GAIN

G GAIN

B GAIN

R GAIN

G GAIN

B GAIN

R GAIN

G GAIN

B GAIN

CMD(HEX)

F3

F4

16

18

1A

16

18

1A

16

18

1A

ADR

00

00

00

01

02

VALUE

FF/00

00 - FE

00 - FE

00 - FE

00 - FE

00 - FE

00 - FE

00 - FE

00 - FE

00 - FE

Detail

OO : OFF

01 : ON

FF : WB Ready

0x10 : TV

0x20 : AV1

0x21 : AV2

0x23 : AV3

0x40 : Component1

0x50 : RGB DTV

0x60 : RGB PC

0x90 : HDMI1 DTV

GAIN adjustment

CSM COOL

GAIN adjustment

CSM NORMAL

GAIN adjustment

CSM WARM


* Refer to the below case to know what value is fixed.

* CASE- First adjust the coordinate much away from the target

value(x, y).1) x, y > target

(1) Decrease the R, G. 2) x, y < target

(1) First decrease the B gain.(2) Decrease the one of the others.

- In case of decreasing the x, decreasing the R : fix G- In case of decreasing the y , decreasing the G : fix R

3) x > target , y < target(1) First decrease B, so make y a little more than the

target.(2) Adjust x value by decreasing the R.

4) x < target , y > target(1) First decrease B, so make x a little more than the

target.(2) Adjust x value by decreasing the G.

(7) When adjustment is completed, Exit adjustment modeusing EXIT key on R/C.

10. Default Value in Adjustment mode(Default values maybe modified the module condition)

10-1. White Balance

11. Internal press test

12. Sound spec.

13. POWER PCB Assy VoltageAdjustments (Va, Vs Voltage adjustments)

13-1. Profile : To supply the Va, Vs voltage that the module want.

13-2. Required Test Equipment(1) Stick for adjustment.(2) DMM.

13-3. Connection Diagram for Measuring: refer to (Fig. 1)

13-4. Adjustment Method(1) Va Adjustment

1) After receiving 100% Full White Pattern, HEAT RUN.2) Connect + terminal of D. M..M. to Va pin of P812, connect

-terminal to GND pin of P812.3) After turning VR901,voltage of D.M.M adjustment as

same as Va voltage which on label of panel right/top.(deviation; ±0.5V)

(2) Vs Adjustment1) Connect + terminal of D. M..M. to Vs pin of P812, connect

-terminal to GND pin of P812.2) After turning VR851, voltage of D.M.M adjustment as

same as Vs voltage which on label of panel right/top.(deviation ; ±0.5V)

14. Input the Shipping Option Data

(1) Push the ADJ key in a Adjust Remote control.(2) Input the Option Number that was specified in the BOM,

into the Shipping area.(3) The work is finished, Push A Key.

Item

Dielectric Voltage (AC <-> FG)

Dielectric Voltage (Without FG)

Value

1.5

1.5

3

3

Unit

kV

kV

Remark

At 100mA for 1sec (Line)

At 100mA for 1min (OQC)

At 100mA for 1sec (Line)

At 100mA for 1min (OQC)

Item Min Typ Max Unit Remark

Audio Practical Max Output, L(Mono)/R 9 10 12 W

<Default Value on OSD>

Color Coordinate

x y

0.283±0.003

0.295±0.003

0.329±0.003

11,000K

9,300K

6,500K

0.000

0.000

0.003

0.276±0.003

0.283±0.003

0.313±0.003

COOL

MEDIUM

WARM

Mode Temp uv

(Fig. 1) Connection Diagram of power adjustment for measuring.

Each PCB assembly must be checked by check JIG set.(Because power PCB Assembly damages to PDP Module,especially be careful)


TROUBLESHOOTING

1. No power

(1) Symptom1) Minute discharge does not occur at module.2) Front LED does not activate.

(2) Press check

Plug in the power cord

Start Check

No

Yes

Is the power cordplugged in?

Connect the cable.Plasma(CN1)

No

Yes

Are the line filter andPSU connected?

Replace the fuse.No

Yes

Is the correct fuse forthe PSU in place?

Plasma(F101)

Connect the 15pin cable.

Next remove all cables connected to the PSU andswitch the AV voltage to manual.If the ST-by 5V does not operate, replace the PSU.

No

Yes

Is the PSU and 15pincable connected to the

VSC board?


2. Protect mode

(1) Symptom1) After lighting once it does not discharge minutely from the module. 2) The relay falls.(there is an audible “Click”.)3) The color of the front LED turns from green to red.

(2) Follow check

Is the Power Boardnormal ?

Replace Power Board.Is the output the normal Low/Highvoltage except for the Stand-by 5V?

Yes

No No

Are all the connectorsnormal?

Replace the connector.

Replace the fuse.

Replace the Y-Board.

After checking each connector doesis operate correctly?

Yes

No No

Is the Y-Boardnormal?

Is theappropriate

fuse (FS2,FS1) on theY-B/D?

Is the output voltagenormal after removing theP1 connector of the Y-B/D?

Yes

No No

Is the X- Boardnormal?

Is the output voltage normal

after removing the P11, P12,P13 connector of

the X-B/D?

After removing the P12 and the outputvoltage is normal : Replace the Right X-B/DAfter removing the P11, P13 and the outputvoltage is normal : Replace the Left X-B/D

No

Yes

Start Check


3. No Raster

(1) Symptom1) No OSD or image are displayed on the screen. 2) The front LED remains green.

(2) Follow check

4. In the case an unusual display in RF mode.

Check the PDP Module

Replace thePower board.

Doesminute discharge

at Module?

Is the inverter/VaVs on?

Is output the normalLow/High voltage exceptfor the Stand-by 5V?

Yes

No No

Is the output for theIC500 normal?

Replace the VSC.No

Yes

Check the power.(L1103)

Is the video output of the

Tuner normal? (CheckTU400_Pin13)

Is theinput voltage

normal?(CheckPin3)

Is the I2C communication normal?(Check Pin9, Pin10)

Yes

No Yes

Is the LVDSPattern connected?

Yes

Change the IC(IC500)

Connect againthe Pattern.

No

No

Check the Tuner.

No

A

Start Check


5. In the case of an unusual display in rear AV mode.

Is video input ofthe A/V jack normal?

(Check R113)

Yes

Sam as Block A

Check the input source.No

8. In the case of an unusual display in SCART 1 mode.

Is the video inputof the A/V jack normal?

(Check R113)

Yes

Sam as Block A


9. In the case of an unusual display in SCART 1_RGB mode.

Is thevideo input of

the A/V jack normal?(CheckR115,R116,

R117)

Yes

Sam as Block A


10. In the case of an unusual display in SCART 2 mode.

Is the video input ofthe A/V jack normal?

(Check R149)

Yes

Sam as Block A



11. In the case of an unusual display in component 1 mode.

Is the videoinput of the A/V jack

normal? (Check R235,R236,R250)

Yes



12. In the case of an unusual display in component 2 mode.

Yes



Is the videoinput of the A/V Jack

normal? (Check R243,R244, R245)

13. In the case of an unusual display in RGB mode.

Yes



Is theR, G, B input

and H, V sync of theJK201 normal?(Check R223,

R224, R225, R221,R222)


14. No Sound

(1) Symptom1) LED is green.2) There is a picture but no sound.

(2) Follow check

Is there sound in anymode?

Is the speaker on?

Yes Yes

Is the speakercable normal?

Yes

Yes

Is there no soundonly for HDMI?

Yes

Is there no sound only AV/COM2/PC?

Is the outputof IC600(R609, R608)

normal?

Yes

Is there no soundonly for RF?

No

No

No

No

Download the EDID data.

Set speaker on in the menu.

NoReplace the

IC600

No

Check the Speakercable

No

Is the IC500operating normal? Replace the IC500

No

Yes

Is the IC601operating normal? Replace the IC601

Replace the VSC BD

Yes

Check the signal after IC600.refer to circuit diagram.

Check the Tuner In/Out.

No


15. HDMI mode

Is only videonormal?

Is only audionormal?

No

YesDownload EDID data each port.

Check the TMDS line wave.(R312~E3273)

1. Check the HDMI receiver’s status register. (0x60, offset 0x66)- If the value is 0xf or 0x8, it is normal.

2. Check the HDCP register. (0x6, offset 0x32)- Enable bit 6 : HDCP key loaded- Enable bit 5 : HDCP decryption active- Enable bit 4 : HDCP authentication attempted

Reset TMDS power down/ on register.- 0x60, offset 0x3f => 0xff

Check HDMI source. Change to another source or cable.

Yes

Is the wavecontinuous?

Normal video,Normal audio?

No

Yes

Replace the IC303.No

1. Check TV input mode.(HDMI 1 port support HDMI and DVI.So if you input DVI signal and PC audio fromphone jack, You can hear PC audio.)

2. Unplug and plug in the HDMI cable.(sometimes ESD surge occurred at HDMI port.)

3. Check the HDMI Mute register. (0x68, offset 0x37)4. Check the Audio-out channel mute register (0x68,

offset 0x32) is appropriately enabled.

Yes


BLOCK DIAGRAM

PC_A

udio

RF

SCAR

T1,2

CO

MP1

HD

MI1

(DTV

)

RC

A1

RC

A2

RG

B(P

C)

VAR

IABL

E AU

DIO

OU

T

32PD

P BL

OC

K D

IAG

RAM

EU-O

PTIO

N

CO

MP2

HD

MI2

(DTV

)

NO

NEU

-OPT

ION

VCT_

Pro

(Lip

-syn

c)

EEPR

OM

24C

02

SYN

C S

W74

ACT2

53

DSU

B_SC

L/SD

A

PC_R

/G/B

PC_S

ER_D

ATA/

CLK

PC_V

S/H

S

HD

MI R

xAN

X902

1

#1 R

X 0/

1/2/

CLK

± C

ECEE

PRO

M24

C02

DD

C1_

SCL/

SDA

EEPR

OM

24C

02

#2 R

X 0/

1/2/

CLK

± C

ECD

DC

2_SC

L/SD

A

VS/H

S

DR

I/DG

I/DBI

/[0-7

]

PC_R

/G/B

CEC

CO

MP1

_Y/P

b/Pr

CO

MP1

_L/R

CO

MP2

_Y/P

b/Pr

CO

MP2

_L/R

SC1_

V

SC1_

L/R

MN

T_VO

UT

MN

T_L/

RO

UT

CO

MP

SWST

MAV

340

CO

MP1

_Y/P

b/Pr

CO

MP2

_Y/P

b/Pr

SC1_

R/G

/B

SC_R

/G/B

_CO

MP/

Y/Pb/

Pr

AUD

IO S

WTE

A642

0

PC_A

UD

IO_L

/R

SC1_

L/R

SC2_

L/R

CO

MP2

_L/R

AV_A

UD

IO_L

/RAM

_AU

DIO

_L/R

CO

MP1

_L/R

TV_L

/RO

UT

MN

T_L/

RO

UT

MN

T_VO

UT

TUN

ER

TV_

V

TV_V

OU

T

AM_A

UD

IO

SIF

SC1_

V

SC1_

R/G

/B/F

B/ID

SC1_

L/R

TV_V

OU

TTV_L

/RO

UT

SC2_

VSC

2_ID

SC2_

L/R

MN

T_VO

UT

MN

T_L/

RO

UT

SC1/

2_ID

SC1/

2_V

SC1_

FB

HD

MI_

R/G

/B

PC_A

udio

_L/R

HEA

D_L

/R

EEPR

OM

24C

32

AMP

TPA3

107D

2

SPK_

L/R

SPK_

L-/+

SPK_

R-/+

I2 C

I2 C

I2 C

I2 C

I2 C

PDP

ASIC

4007

RA1

/RB1

/RC

1/R

D1/

RE+

-

I2 C

DIS

P_EN PC

_SER

_DAT

A/C

LK

FLAS

H(1

6 M

)M

X29L

V160

TEM

P IC

ADT7

5AR

Z

XDR

V_O

UT[

0-79

]

X1_C

LK_A

1/2_

B1/2

YSU

S/ER

_UP/

DN

BUFF

ER74

ACT5

4

BUFF

ER74

ACT5

4

YRAM

P_U

P/D

N

BUFF

ER74

ACT5

4ZS

US/

ER_U

P/D

N

YSU

S/ER

_UP/

DN

YRAM

P_U

P/D

N

ZSU

S/ER

_UP/

DN

MEMO



EXPLODED VIEW30

0

570

560

120

301

302

303

304

305

200

240

580

250

400

520

590

201

202

203

900

306

A2

A21


120 EAB33496901 Speaker,Full Range 5B084 ND 10W 8OHM 82DB 120HZ 147 X 42 X 31 LUG ESTEC ELECTRONICS JIAXING

200 EAJ39835901 PDP, Module-VGA PDP32F10110.AKLGG VGA 32INCH 852X480 16/9 PDP DIVISION

EAJ41358001 PDP, Module-VGA PDP32F10110.ASLGB VGA 32INCH 852X480 16/9 PDP DIVISION SKD

201 EBR36450301 Auto SMT PCB Assembly, XRLB ASSY SMD TOP INSERT 32” 32V1 4layer TCP256ch PDP DIVISION

202 EBR36450601 Auto SMT PCB Assembly, XRRB ASSY SMD TOP INSERT 32” 32V1 4Layer TCP256ch PDP DIVISION

203 EBR36450901 Auto SMT PCB Assembly, YSUS ASS’Y SMD TOP INSERT 32” 32V1 2Layer PDP DIVISION

240 AJJ34139401 Supporter Assembly, 32 PDP SUPP. MODULE VERTICAL ASSY RIGHT

AJJ34139403 Supporter Assembly, 32PC5, SUPP. MODULE VERTICAL ASSY RIGHT, CSKD

250 AJJ34139402 Supporter Assembly, 32 PDP SUPP. MODULE VERTICAL ASSY LEFT

AJJ34139404 Supporter Assembly, 32PC5, SUPP. MODULE VERTICAL ASSY LEFT, CSKD

300 ABJ34138802 Cabinet Assembly, 32PV5RV-TB, 32PV5RV-ZB H4 32” CABINET ASSY

ABJ34138811 Cabinet Assembly, 32PC51-ZB PP78C 32” PHANTOM LGEMA

301 AJJ34139001 Supporter Assembly, 32 PDP SUPP. FILTER TOP ASSY

AJJ34139002 Supporter Assembly, 32 PDP SUPP. FILTER TOP ASSY CSKD

302 AJJ34139101 Supporter Assembly, 32 PDP SUPP. FILTER BOT. ASSY

AJJ34139102 Supporter Assembly, 32PC5, SUPP. FILTER BOT. ASSY, CSKD

303 AJJ34139201 Supporter Assembly, 32 PDP SUPP. FILTER RIGHT ASSY

AJJ34139202 Supporter Assembly, 32 PDP SUPP. FILTER RIGHT ASSY CSKD

304 AJJ34139301 Supporter Assembly, 32 PDP SUPP. FILTER LEFT ASSY

AJJ34139302 Supporter Assembly, 32 PDP SUPP. FILTER LEFT ASSY CSKD

305 MDJ40627001 Filter, CUTTING ACRYL GLASS FILTER PDP 32” SKC without AR

306 MAZ39574301 Bracket, MOLD ABS COVER 32PC5 - ABS BRACKET 2

MAZ39574302 Bracket, MOLD ABS COVER 32PC5 - ABS BRACKET 2, CSKD

400 ACQ34138902 Cover Assembly, Rear 32 H4 32” PDP B/C ASSY, EU

ACQ34138905 Cover Assembly, Rear 32PC51-ZB PP78C 32” TYPE “B” CSKD

520 EBR39931504 Hand Insert PCB Assembly, Main MAIN M.I PP78C 32PC51-ZB AUSLLHX 32inch PDP Hand Insert for EU

560 EBR39221401 Hand Insert PCB Assembly, Sub CONTROL M.I PP78A 32PC5RV-MF ALALLHX LocalKey

EBR39221404 Hand Insert PCB Assembly, Sub CONTROL M.I PP78A 32PC5RV-MF ALALLHX LocalKey

570 EBR39220901 Hand Insert PCB Assembly, Sub SUB M.I PP78A 32PC5RV-MF ALALLHX PreAMP+LED

580 EAY39810701 SMPS, AC/DC EAY39810701 90VTO264V 250W 50~60 UL 32” PDP PSU ( PDP TV division ) PDP DIVISION

590 EAM35012705 Filter, AC Line IF2-N06AEW1 5.3mH 250VAC 6A 0.1uF 1000pF YH396-03 150/50MM VDE/CSA/K HOUSING/RING BK

900 AAN34139601 Base Assembly, BASE 32 - PDP

AAN34139603 Base Assembly, BASE 32PC51-ZB PP78C ROUND PC5 CONCEPT, PHANTOM LGEMA

A2 AKB34907202 Remote Controller Assembly, 32PC5RV-TB, 32PC51V-ZB

A21 3550V00407B Cover, MOLD ABS HF380 32PC5RV-MF ABS, HF-380 AKB34907203, BK, CKD FOR LGEAZ

EXPLODED VIEW PARTS LIST

No. Part No. Descriptions

The components identified by mark iscritical for safety.Replace only with part number specified.


C100 0CC102CK41A Ceramic,ChipC1608C0G1H102JT 1nF 5% 50V C0G -5


C100 0CH5101K416 Ceramic,ChipC2012C0G1H101JT 100pF 5% 50V C0G

C1000 0CK104BF56A Ceramic,ChipC1005X7R104KET 100nF 10% 16V X7R


C1001 0CK104CF56A Ceramic,Chip0603B104K160CT 100nF 10% 16V X7R




C1003 0CE226WF6DC AL,ChipMVK5.0TP16VC22M 22uF 20% 16V 30MA


C1004 0CK105DH56A Ceramic,ChipC2012X7R105KFT 1uF 10% 25V X7R -5

C1004 0CK105DH56A Ceramic,ChipC2012X7R105KFT 1uF 10% 25V X7R -5

C101 0CE476VF6DC AL,ChipVGV476M016S0ANE010 47uF 20% 16V 7




C102 0CK106EF56A Ceramic,ChipC3216X7R1C106KT 10uF 10% 16V X7R





C104 0CE227SF6DC AL,ChipMVG6.3TP16VC220M 220uF 20% 16V 13


C104 0CH4471K416 Ceramic,ChipC2012C0G1H471JT 470pF 5% 50V C0G





C107 0CK682CK51A Ceramic,ChipC1608Y5P1H682KT 6.8nF 10% 50V Y5P




























C207 0CK103CK56A Ceramic,Chip0603B103K500CT 10nF 10% 50V X7R -




















C220 0CK105CF94A Ceramic,Chip0603F105Z160CT 1uF -20TO+80% 16V






















LOC. NO. PART NO. DESCRIPTION / SPECIFICATION LOC. NO. PART NO. DESCRIPTION / SPECIFICATION

REPLACEMENT PARTS LIST

DATE: 2007. 09. 08.

CAPACITORs

C307 0CC220CK41A Ceramic,ChipC1608C0G1H220JT 22pF 5% 50V C0G -














C314 0CK103CK51A Ceramic,Chip0603B103K500CT 10nF 10% 50V Y5P -

C314 0CK103CK51A Ceramic,Chip0603B103K500CT 10nF 10% 50V Y5P -







C401 0CE107WF6DC AL,ChipMVK6.3TP16VC100M 100uF 20% 16V 11










C406 0CK104CK56A Ceramic,Chip0603B104K500CT 100nF 10% 50V X7R










C500 0CK225DD66A Ceramic,ChipLMK212JB225MG-T 2.2uF 20% 10V X7R

C500 0CK225DD66A Ceramic,ChipLMK212JB225MG-T 2.2uF 20% 10V X7R































C516 0CK474CH94A Ceramic,Chip0603F474Z250CT 470nF -20TO+80% 25












C522 0CE335WK6D8 AL,ChipMVK4.0TP50VC3.3M 3.3uF 20% 50V 14

C522 0CE335WK6D8 AL,ChipMVK4.0TP50VC3.3M 3.3uF 20% 50V 14



C524 0CK332CK56A Ceramic,ChipC1608X7R1H332KT 3.3nF 10% 50V X7R


























































C552 0CK475DD56A Ceramic,ChipC2012X7R1A475KT 4.7uF 10% 10V X7R






















C563 0CK475EF56A Ceramic,ChipC3216X7R1C475KT 4.7uF 10% 16V X7R

C563 0CK475EF56A Ceramic,ChipC3216X7R1C475KT 4.7uF 10% 16V X7R









C602 0CK475EF67A Ceramic,ChipC3216X5R1C475MT 4.7uF 20% 16V X5R














C610 0CC471CK41A Ceramic,ChipC1608C0G1H471JT 470pF 5% 50V C0G










C616 0CK102CK56A Ceramic,Chip0603B102K500CT 1nF 10% 50V X7R -5












C622 0CK105DK94A Ceramic,Chip0805F105Z500CT 1uF -20TO+80% 50V










C626 0CE106WH6DC AL,ChipMVK5.0TP25VC10M 10uF 20% 25V 25MA

C626 0CE106WH6DC AL,ChipMVK5.0TP25VC10M 10uF 20% 25V 25MA







C630 0CK224DK46A Ceramic,Chip0805B224J500CT 220nF 5% 50V X7R -

















C638 0CK105DK94A 0805F105Z500CT 1uF -20TO+80% 50V

C639 0CE227WJ6DC MVK10TP35VC220M 220uF 20% 35V 375


C640 0CK225DK94A CL21F225ZBFNNNE 2.2uF -20TO+80% 5










C645 0CK104CK56A 0603B104K500CT 100nF 10% 50V X7R




C647 0CK474CH94A 0603F474Z250CT 470nF -20TO+80% 25

C647 0CK474CH94A 0603F474Z250CT 470nF -20TO+80% 25

C648 0CK103CK56A 0603B103K500CT 10nF 10% 50V X7R -






C700 0CE107WF6DC MVK6.3TP16VC100M 100uF 20% 16V 11




C702 0CK474CH94A 0603F474Z250CT 470nF -20TO+80% 25

C702 0CK474CH94A 0603F474Z250CT 470nF -20TO+80% 25

C703 0CK474CH94A 0603F474Z250CT 470nF -20TO+80% 25

C703 0CK474CH94A 0603F474Z250CT 470nF -20TO+80% 25







C707 0CE477WF6DC MVK10TP16VC470M 470uF 20% 16V 80M

C707 0CE477WF6DC MVK10TP16VC470M 470uF 20% 16V 80M









C712 0CE476WF6DC MVK6.3TP16VC47M 47uF 20% 16V 80MA




























C800 0CK104CF56A 0603B104K160CT 100nF 10% 16V X7R


C801 0CK105DH56A C2012X7R105KFT 1uF 10% 25V X7R -5








C804 EAE32755801 CL31A106K5HNNNE 10uF 10% 16V X5R

C804 EAE32755801 CL31A106K5HNNNE 10uF 10% 16V X5R















C813 0CK104BF56A C1005X7R104KET 100nF 10% 16V X7R

C813 0CK104BF56A C1005X7R104KET 100nF 10% 16V X7R





































































D100 EAH33946001 CDS3C05GTA 5.6V 6.4V 19V 1.9A 1W


D101 0DR050008AA SD05.TC - 6V 14.5V 24A 350W SOD32

D101 EAH33945901 CDS3C30GTH 30V 50V 120V 1.9A 1W S


















DIODEs










D206 0DS226009AA KDS226 1.2V 85V 300MA 2A 4NSEC 15










D211 0DSIH00028A MC2838-T112-1 1.2V 75V 300MA 4A 3

D211 0DSIH00028A MC2838-T112-1 1.2V 75V 300MA 4A 3

























D300 0DSIH00028A MC2838-T112-1 1.2V 75V 300MA 4A 3

D300 0DSIH00028A MC2838-T112-1 1.2V 75V 300MA 4A 3

D301 0DSIH00028A MC2838-T112-1 1.2V 75V 300MA 4A 3

D301 0DSIH00028A MC2838-T112-1 1.2V 75V 300MA 4A 3

ZD200 0DR050008AA SD05.TC - 6V 14.5V 24A 350W SOD32








ZD700 0DZKE00048A KDZ8.2V 8.2V 7.7TO8.7V 20OHM 200M

ZD700 0DZKE00048A KDZ8.2V 8.2V 7.7TO8.7V 20OHM 200M

D100 0DLBE0138AA BL-BUBGE301 ROUND 3MM SUPER RED/G

D700 0DL233309AC SAM2333 RED/Y-GREEN 2.7V 2.8V 30m

D700 0DL233309AC SAM2333 RED/Y-GREEN 2.7V 2.8V 30m

D800 EAV38290401 BL-HGE33A-TRB Y-GREEN 2~2.6V 30mA






IC1000 0ISTLFA032A 74ACT541MTC 4.5TO5.5V 0.004mA BUF






IC200 0IMMRAL014D AT24C02BN-SH-T 2KBIT 256x8BIT 1.8


IC201 0ISTL00031A MC74HC4066ADR2G MC74HC4066ADR2G,L

IC201 0ISTL00031A MC74HC4066ADR2G MC74HC4066ADR2G,L

IC202 0IFA742530B 74ACT253SC 4.5TO5.5V 0.004mA MULT

IC202 0IFA742530B 74ACT253SC 4.5TO5.5V 0.004mA MULT

IC203 EAN32724702 STMAV340 4.0TO5.5V 5NSEC 5NSEC 0W

IC203 EAN32724702 STMAV340 4.0TO5.5V 5NSEC 5NSEC 0W

IC300 0IPRP00735A ANX9021 3.3V 60u 17MHZ TQFP TR 14

IC300 0IPRP00735A ANX9021 3.3V 60u 17MHZ TQFP TR 14





IC500 EAN35336801 VCT7993P- FA-A1-H-000 1.71VTO1.89

IC500 EAN35336801 VCT7993P- FA-A1-H-000 1.71VTO1.89

IC501 0IMMRAL025A AT24C32AN-10SU-2.7 32KBIT 4096X8B

IC501 0IMMRAL025A AT24C32AN-10SU-2.7 32KBIT 4096X8B

IC502 0IFA752700A KA75270Z 2.55TO2.85V 0 200MW TO92

IC502 0IFA752700A KA75270Z 2.55TO2.85V 0 200MW TO92

IC600 0IPRP00665A TEA6420D 8TO10.2V 8mA 0 SO R/TP 2

IC600 0IPRP00665A TEA6420D 8TO10.2V 8mA 0 SO R/TP 2

IC601 EAN35502001 TPA3107D2 10TO26V 50mV 0.1% 15W 0

IC601 EAN35502001 TPA3107D2 10TO26V 50mV 0.1% 15W 0

IC700 0IPMGA0010A AZ1117H-3.3 4.75TO10V 3.3V 0W SOT


IC701 0IPMG78341A AZ1085S-3.3TR/E1,LF 12V 3.3V 0W T

IC701 0IPMG78341A AZ1085S-3.3TR/E1,LF 12V 3.3V 0W T

IC702 EAN34140401 AZ1085S-1.8TRE1 1.238V to 12V 1.

IC702 EAN34140401 AZ1085S-1.8TRE1 1.238V to 12V 1.



LEDs

ICs

IC703 0IPMG00049A AZ1117H-1.8TR/E1[H13A] 3.2TO10V 1

IC703 0IPMG00049A AZ1117H-1.8TR/E1[H13A] 3.2TO10V 1



IC801 EAN41581002 32inch PDP 16M Flash ROM 32FS1 Ve

IC801 EAN41581002 32inch PDP 16M Flash ROM 32FS1 Ve

IC801 0IMMRMR010F MX29LV160CTTC-70G 16MBIT 2MX8BIT_

IC801 0IMMRMR010F MX29LV160CTTC-70G 16MBIT 2MX8BIT_

IC802 0ILNRAA001B S7136F -0.3TO15V 0.4V 400MW SOT-8

IC802 0ILNRAA001B S7136F -0.3TO15V 0.4V 400MW SOT-8

IC803 EAN37283701 PQ010GN01ZPH 1.7TO5.5V 1V 8W SC63

IC803 EAN37283701 PQ010GN01ZPH 1.7TO5.5V 1V 8W SC63

IC806 0ISTLFA024A MM74HC00M 2TO6V 0.002mA NAND GATE

IC806 0ISTLFA024A MM74HC00M 2TO6V 0.002mA NAND GATE

IC900 EAN37528301 LGDP4007 SPTCDA IC (WVGA) 3.3V /

IC900 EAN37528301 LGDP4007 SPTCDA IC (WVGA) 3.3V /

AR300 6210TCE002B HB-4M3216-121JT 120OHM 3.2X1.6X1.












F1 6210VH0001A 6210VH0001A 50OHM 25MM 9MM 32MM R

F2 6210VH0004B ZCAT1518-0730-M- K 65OHM 15MM 7MM

L100 6210TCE001A HB-1S2012-080JT 8OHM 2X1.25X1MM S


L1000 6200J000132 CNH20T105M EMI 0HZ 1uF 0H SMD R/T


L1001 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1001 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1002 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1002 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1003 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1003 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1004 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1004 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1005 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1005 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1006 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1006 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1007 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1007 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1008 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1008 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1009 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L1009 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

























L205 6200J00005N HH-1M2012-121JT(H:1mm) 120OHM 2X1




L207 6210TCE001G HH-1M3216-501JT 500OHM 3.2X1.6X1.












L401 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L401 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L402 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L402 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L403 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L403 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L404 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L404 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L405 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L405 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L406 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L406 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.






FILTERs & INDUCTORs


L502 6210TCE001B HH-1H3216-500JT 50OHM 3.2X1.6X1.3










L604 6210TCE001P HB-1S2012-121JT(H:1mm) 120OHM 2X1












































R416 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R416 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R417 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R417 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R418 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R418 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R419 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R419 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R420 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R420 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R421 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R421 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R422 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R422 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R423 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

R423 6200J00005R HB-1M1608-501JT 500OHM 1.6X0.8X0.

L100 0LC1032101A Inductor, FI-C3216-103KJT 10UH 10% - 50MA 0

L600 0LCML00020C Inductor, MLI-201212-100K 10UH 10% - 15MA 1




L602 EAP32842807 Inductor, NR8040T330M 33UH 20% 250V 1.7A 0.








IC303 0TFTH80001A FET, SSM6N15FU N-CHANNEL MOSFET 30V +-






Q100 0TRIY80001A 2SC3052 NPN 6V 50V 50V 200MA 100N



















FETs & TRANSISTORs




Q400 0TRIH80002A 2SA1530A-T112-1R PNP -6V -60V -50












Q501 0TR102009AM KRA102S PNP -30V 0V -50V -0.1A -0

Q501 0TR102009AM KRA102S PNP -30V 0V -50V -0.1A -0



























AR1000 0RJ0222C692 MNR04 M0APJ 220 22OHM 5% 1/16W 10
















































AR1024 0RJ0472C687 RCA86TRJ47R0 47OHM 5% 1/16W 4 SMD

AR1024 0RJ0472C687 RCA86TRJ47R0 47OHM 5% 1/16W 4 SMD











AR800 EBC32260404 MNR04M0APJ100 10OHM 5% 1/16W 4 SM






RESISTORs



AR803 EBC32260901 MNR04M0APJ102 1KOHM 5% 1/16W 4 SM

AR803 EBC32260901 MNR04M0APJ102 1KOHM 5% 1/16W 4 SM

L1001 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1608 R


















L208 0RH0000D622 MCR10EZHJ000 0OHM 5% 1/8W 2012 R/

L208 0RH0000D622 MCR10EZHJ000 0OHM 5% 1/8W 2012 R/















R100 0RH0000D622 MCR10EZHJ000 0OHM 5% 1/8W 2012 R/

R100 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1608 R




R102 0RH1002D622 MCR10EZHJ103 10KOHM 5% 1/8W 2012

R102 0RH1101D622 MCR10EZHJ112 1.1KOHM 5% 1/8W 2012






R103 0RH2001D622 MCR10EZHJ202 2KOHM 5% 1/8W 2012 R


R103 0RJ0752D677 MCR03EZPJ750 75OHM 5% 1/10W 1608


R1031 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10W 160




R1034 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W 1608

























































R239 0RJ2002D677 MCR03EZPJ203. 20KOHM 5% 1/10W 160


























































R324 0RJ0102C678 MCR01MZPJ100 10OHM 5% 1/16W 1005












































































R365 0RJ1004D677 MCR03EZPJ105 1MOHM 5% 1/10W 1608

R365 0RJ1004D677 MCR03EZPJ105 1MOHM 5% 1/10W 1608



















R378 0RJ0000G676 MCR18EZHJ00 0OHM 5% 1/4W 3216 R/T

R378 0RJ0000G676 MCR18EZHJ00 0OHM 5% 1/4W 3216 R/T

























































R509 0RJ3001C678 MCR01MZPJ302 3KOHM 5% 1/16W 1005






















































R903 0RJ4701C678 MCR01MZPJ472 4.7KOHM 5% 1/16W 100




























C1 6631900018P Harness, 3P(LEFT) SPK CONNECTOR ASSY SMH25

C2 6631900108A Harness, EAD00387601 SMH200 SMH200 300mM 2

C3 6631T25023H Harness, SMH250-15 SMH250-15 300mM 2.50MM

C4 6631T25023H Harness, SMH250-15 SMH250-15 300mM 2.50MM

C5 6631T25024H Harness, 4P(H-T) CONNECTOR ASSY SMH250 350

C6 EAD36774102 Harness, 8P 1533 12505HS-8 12505HS-8 400MM

JK200 6630G00003A ZDAFA1-C0L0-4F D-SUB 15P 2.29MM S

JK200 6630G00003A ZDAFA1-C0L0-4F D-SUB 15P 2.29MM S

P1000 6630XA02453 GF05A-50S-AF 50P 0.5MM FFC ANGLE






CN101 6602T20009E Wafer, SMAW200-06P 6P 2.00MM 1R ANGLE DI

CN100 6602T12005G Wafer, 12505WR-08A00 8P 1.25MM 1R ANGLE

P100 6602T20009E Wafer, SMAW200-06P 6P 2.00MM 1R ANGLE DI

P1002 6630VJ01805 Wafer, 15001WR-05A00 5P 1.50MM 1R ANGLE

P1002 6630VJ01805 Wafer, 15001WR-05A00 5P 1.50MM 1R ANGLE

P200 6630VF01608 Wafer, 53398-0890 8P 1.25MM 1R STRAIGHT

P200 6630VF01608 Wafer, 53398-0890 8P 1.25MM 1R STRAIGHT

P600 6602T25008B Wafer, SMW250-03P 3P 2.50MM 1R STRAIGHT

P600 6602T25008B Wafer, SMW250-03P 3P 2.50MM 1R STRAIGHT

P601 6602T25008C Wafer, SMW250-04P 4P 2.50MM 1R STRAIGHT

P601 6602T25008C Wafer, SMW250-04P 4P 2.50MM 1R STRAIGHT

P700 6602T25009P Wafer, SMAW250-15P 15P 2.50MM 1R ANGLE D

P700 6602T25009P Wafer, SMAW250-15P 15P 2.50MM 1R ANGLE D

P800 6630VF03415 Wafer, 12505WS-15A00 15P 1.25MM 1R STRAI

P800 6630VF03415 Wafer, 12505WS-15A00 15P 1.25MM 1R STRAI

P801 6602T12004C Wafer, 12505WS-04A00 4P 1.25MM 1R STRAIG

P801 6602T12004C Wafer, 12505WS-04A00 4P 1.25MM 1R STRAIG



HARNESSs & CONNECTORs

JK100 6612M00010A PSC003-01 21P 21P/1C 3.81MM STRAI




JK201 6612J10031A PPJ209-02 14.0MM 1RX5C STRAIGHT T

JK201 6612J10031A PPJ209-02 14.0MM 1RX5C STRAIGHT T

JK203 6612F00099A PEJ024-01 1P 4P STRAIGHT TR 3.6MM

JK203 6612F00099A PEJ024-01 1P 4P STRAIGHT TR 3.6MM

JK300 6612B00015B DC1R019WDH SOCKET 21P STRAIGHT SM




JK600 6612J10043A PPJ200-07 15MM 1RX4C ANGLE BK 3P

JK600 6612J10043A PPJ200-07 15MM 1RX4C ANGLE BK 3P

SW101 140-313B KPT-1115AM 1C1P 12VDC 0.05A HORIZ








SW500 6600VR1004A SKHMPWE010 1C1P 12VDC 0.05A HORIZ

SW500 6600VR1004A SKHMPWE010 1C1P 12VDC 0.05A HORIZ

B1 3890TKD002P Box, LB500J(PCB) BRAND 542*397*445

B2 MAY39942301 Box, BOX DW 1035 194 640 2 COLOR 32PC5

X300 6212AB2883A Crystal, HC-49SM 27.00000MHZ 27MHZ 30PPM

X300 6212AB2883A Crystal, HC-49SM 27.00000MHZ 27MHZ 30PPM

X500 6202VDT002P Crystal, HC-49/SM 20.25000MHZ 20.25MHZ 30PPM

X500 6202VDT002P Crystal, HC-49/SM 20.25000MHZ 20.25MHZ 30PPM

X501 6212AB4006B Crystal, SCO-103S 50MHZ 50PPM 16pF SCO-103

X501 6212AB4006B Crystal, SCO-103S 50MHZ 50PPM 16pF SCO-103

IC100 6712000014A Receiver Module, KSM-2013TH2A 4.5TO5.5V 12.4M

SA1 SAA31059304 S/W, Firmware 3.00 BB93 EUROPE FLASH ROM

IC805 0IZZQ00010A Sensor, Temperature ADT75ARZ 3.0TO5.5V

IC805 0IZZQ00010A Sensor, Temperature ADT75ARZ 3.0TO5.5V

TU400 EBL41088201 Tuner, Tuner/Modulator TAFT-W006D PAL-B/G+I+D/K

TU400 EBL41088201 Tuner, Tuner/Modulator TAFT-W006D PAL-B/G+I+D/K

A1 SAC30653122 Title, PP78C CD MANUAL 32PC51-ZB

A1 MFL37396717 Manual, Owners EN H4 simple book

A1 MFL37396722 Manual, Owners EN/HE H4 simple book H.Y.C SET

A2 AKB34907202 Remote Controller Assembly, 32PC5RV-TB, 32PC51V-ZB

A21 3550V00407B Cover, MOLD ABS HF380 ABS, CKD FOR LGEAZ

A3 EAD36223101 Power Cord, LONGWELL COMPANY UK

A3 EAD36430001 Power Cord, LP34A+LS60L 1.87M LACK

A3 EAD36431301 Power Cord, LP-42 + LS-60L 1.87M BLACK SET

A4 MAZ39574101 Bracket, MOLD ABS COVER 32PC5 - ABS BRACKET 1

A5 3880TKZ004E Bag, COMPLEX VINYL 180*150 0.58 H&C MODEL

A6 4950TKA320A Plate, PRESS SBHG T1.2 SUPPORT UPSET

A7 FAB30016409 Screw Assembly, FAB30016409 MACHINE TYPE D4.0

A8 FAB30016418 Screw Assembly, FAB30016418 MACHINE TYPE D4.0



ACCESSORY

OTHERs

JACKs

SWITCHs

LGE Internal Use OnlyCopyright©2007 LG Electronics. Inc. All right reserved. Only for training and service purposes

MAIN(TOP) MAIN(BOTTOM)CONTROL(TOP)

CONTROL(BOTTOM)

PRE-AMP(BOTTOM)PRE-AMP(TOP)

PRINTED CIRCUIT BOARD

Oct., 2007Printed in KoreaP/NO : MFL40431002

32pc51

Documents