8/16/2019 32sPACE WAGON

1/8

8/16/2019 32sPACE WAGON

2/8

POWER PLANT MOUNT -   General Information32-2

GENERAL INFORMATION   32100010150

The engine-transmission mount is of an inertial axissupporting type whose excellent features havealready been proven in many Mitsubishi vehicles.The inertial axis supporting type mount supports

the front upper part of the engine at the front andthe rear upper part of the transmission at the rear.This arrangement effectively suppresses the enginevibration.

Dynamic damper

Engine mount

Frontmember

Engine mount

Front

Front roll stopper

Transmission mount

Rear roll stopper

Dynamic damper

Front roll stopper

Transmission mount

Rear roll stopper

Frontmember

Front

8/16/2019 32sPACE WAGON

3/8

POWER PLANT MOUNT -   Engine Mounting   32-3

ENGINE MOUNTING   32100110263

REMOVAL AND INSTALLATION

CautionProvisionally tighten the parts marked by an asterisk (*), and then fully tighten after loading thefull weight of the engine on the vehicle body.

Pre-removal and Post-installation OperationD   Engine Cover Removal and InstallationD   Jack Up the Engine and Transmission Assembly

until Weight is off the Insulator.

5 Nm

12 Nm

67Nm

57Nm

88 - 108 Nm*

1

2

3

45

Removal steps

1. Oil reserver2. Engine mount insulator mounting

bolt

3. Engine mount bracket"AA   4. Engine mount stopper

5. Dynamic damper

INSTALLATION SERVICE POINT

"AAENGINE MOUNT STOPPER INSTALLATION

Install the engine mount stopper so that the arrow faces thedirection shown.

Enginemountstopper

Engineside

 Arrow

Engine mount bracket

8/16/2019 32sPACE WAGON

4/8

POWER PLANT MOUNT -   Transmission Mounting32-4

TRANSMISSION MOUNTING   32100140170

REMOVAL AND INSTALLATION

CautionProvisionally tighten the parts marked by an asterisk (*), and then fully tighten after loading thefull weight of the engine on the vehicle body.

Pre-removal and Post-installation OperationD   Air Cleaner Assembly Removal and Installation

(Refer to GROUP 15)D   Frontmember Removal and Installation

(Refer to P.32-5.)

81 Nm*

57 Nm

2

1

2

Removal steps

AA"   1. Transmission mount bracket"AA   2. Transmission mount stoppers

REMOVAL SERVICE POINT

AA" TRANSMISSION MOUNT BRACKET REMOVAL

1. Support the engine and transmission assembly with agarage jack.

2. Remove the transmission mount bracket mounting boltsand nuts.

3. After lowering the engine and transmission assembly,remove the transmission mount bracket.

8/16/2019 32sPACE WAGON

5/8

8/16/2019 32sPACE WAGON

6/8

POWER PLANT MOUNT -   Frontmember32-6

8

11

88 - 108 Nm

177 Nm

78 Nm

57 Nm*13Nm

69Nm12Nm

16

2

1

4

5

6

14  10

10

13

12

3

39Nm

39Nm

98 - 118 Nm*

98 - 118 Nm44 Nm*

177 Nm

9

7

15

57 Nm*88 - 108 Nm*

Frontmember removal steps

AA"   1. Steering gear and linkage mountingbolt

2. Oil line mounting bolt3. Stabilizer link connection4. Stay

"BA   5. Lower arm assembly connection6. Front roll stopper connecting bolt7. Rear roll stopper connecting bolt

AB"   8. Frontmember mounting bolt

9. Lower stopper10. Upper stopper

11. Front hanger"AA   12. Stabilizer bar13. Lower arm assembly14. Front roll stopper15. Rear roll stopper16. Frontmember

8/16/2019 32sPACE WAGON

7/8

POWER PLANT MOUNT -   Frontmember   32-7

REMOVAL SERVICE POINT

AA"STEERING GEAR AND LINKAGE MOUNTINGBOLT REMOVAL

Use a wire to fix the steering gear box on the vehicle beforeremoving the steering gear and linkage mounting bolts.

AB" FRONTMEMBER MOUNTING BOLT REMOVAL

1. Use a wire to fix the radiator on the vehicle beforeremovingthe frontmember.

2. Support the frontmember with a garage jack and a woodenboard, and remove the frontmember mounting bolts.

INSTALLATION SERVICE POINT

"AASTABILIZER BAR INSTALLATION

1. Install the bushing so that its cutting faces the directionshown.

2. Place the stabilizer bar identification mark at the left of the vehicle and position it as shown in the illustration.Tighten the stabilizer bar bracket mounting bolts.

"BA LOWER ARM ASSEMBLY INSTALLATION

1. Install the lower arm assembly to the knuckle.

CautionBe careful that the ball joint stud does not projectmore than 4 mm from the knuckle (A shown).

2. Replace the dust cover if grease spouted out due tothe knuckle too much pressed in.

3. Check that no clearance is present between the knuckleand dust cover.

Woodenboard

Transmission jack

Front of vehicle

Bushing

 Approx. 20 mm

Knuckle

Lower armassembly

A

8/16/2019 32sPACE WAGON

8/8

POWER PLANT MOUNT -   Roll Stopper32-8

ROLL STOPPER   32100140170

CautionProvisionally tighten the parts marked by an asterisk (*), and then fully tighten after loading thefull weight of the engine on the vehicle body.

98 - 118Nm*

12

3

4

44 Nm*

57 Nm*

57 Nm*

Front roll stopper removal steps

D   Radiator (Refer to GROUP 14)1. Front roll stopper connecting bolt2. Front roll stopper

Rear roll stopper removal steps

3. Rear roll stopper connecting bolt4. Rear roll stopper