4 3 6 L U L T R A F O R M ® S TA I N L E S S S T E E L

436L ULTRA FORM®

STAINLESS STEELD A T A S H E E T

Applications PotentialAK Steel’s 436L ULTRA FORM® is a ferritic grade of stainless steel that outperforms Types 409, 430 and 439 in oxidation and corrosion resistance. This product is resistant to stress corrosion cracking in the presence of chlorides and has excellent formability. This material is ideally suited to automotive exhaust and other applications where high temperatures or resistance to chlorides in a wet corrosive environment is needed. Applications include fuel filler tubes, heat exchangers, and automotive exhaust components.

Improved Pitting Resistance Non-hardening

Weldable Formable

436L ULTRA FORM® STAINLESS STEEL

AK Steel 436L ULTRA FORM® is a nominal 17% Cr, Ti stabilized alloy with Mo added to improve crevice and pitting corrosion resistance. The addition of molybdenum enhances pitting resistance when compared to other ferritic materials such as Type 409, Type 430, and Type 439. It is readily welded and resists intergranular corrosion. Its general corrosion resistance is superior to Type 430 and Type 439. It has a higher thermal conductivity and lower coefficient of expansion than Type 304. It is non-hardening when heated over 1000 °F (538 °C).

AVAILABLE FORMS AK Steel offers 436L ULTRA FORM in thicknesses from 0.015 – 0.100 in., (0.381 – 2.51 mm). Widths are available up to 48 in., (1219 mm). For other sizes, please contact your AK Steel sales representative.

Values shown in this bulletin were established in U.S. customary units. The metric equivalents may be approximate.

COMPOSITION (wt %)

Carbon (C) 0.03 max.

Manganese (Mn) 1.00 max.

Phosphorous (P) 0.04 max.

Sulfur (S) 0.03 max.

Silicon (Si) 1.00 max.

Chromium (Cr) 16.0 – 18.0

Molybdenum (Mo) 0.75 – 1.5

Titanium (Ti) 0.05 max.

PRODUCT DESCRIPTION

4 3 6 L U L T R A F O R M ® S TA I N L E S S S T E E L

AK Steel Corporation9227 Centre Pointe DriveWest Chester, OH 45069844.STEEL99 | 844.783.3599www.aksteel.comsales@aksteel.com

436L ULTRA FORM® STAINLESS STEEL

4 3 6 L U L T R A F O R M ® S TA I N L E S S S T E E L

PROPERTIES

TABLE 1 – TYPICAL MECHANICAL PROPERTIES ANNEALED CONDITION

UTSksi. (MPa)

0.2% YSksi. (MPa)

Elongation % in 2" (50.8 mm)

RockwellHardness

71 (490) 47 (324) 31 B78

CORROSION RESISTANCEAK Steel’s 436L ULTRA FORM exhibits superior corrosion resistance in synthetic muffler condensate testing when compared to Type 409, Type 430 and Type 439.

OXIDATION RESISTANCEType 436L ULTRA FORM is more resistant to high temperature oxidation than Type 409. This is especially true for temperatures exceeding 1500 °F (816 °C).

WELDABILITYThis stabilized ferritic stainless steel grade is generally considered to be weldable by the common fusion and resistance techniques. Special consideration is required to avoid brittle weld fractures during fabrication by minimizing discontinuities and maintaining low weld heat input. AWS classification filler wire EC439 Nb may be used for light gauge high temperature service (>1000 °F) where thermal cycling is expected. ER/EC 309 filler is generally recommended for welds in light gauge material where high temperatures are not anticipated.

AK Steel is a world leader in the production of flat-rolled carbon, stainless and electrical steel products, primarily for automotive, infrastructure and manufacturing, construction and electrical power generation and distribution markets. Headquartered in West Chester, Ohio (Greater Cincinnati), the company employs approximately 8,000 men and women at eight steel plants, two coke plants and two tube manufacturing plants across six states: Indiana, Kentucky, Michigan, Ohio, Pennsylvania and West Virginia. Additional information about AK Steel is available at www.aksteel.com.

The information and data in this document are accurate to the best of our knowledge and belief, but are intended for general information only. Applications suggested for the materials are described only to help readers make their own evaluations and decisions, and are neither guarantees nor to be construed as express or implied warranties of suitability for these or other applications.

Data referring to material properties are the result of tests performed on specimens obtained from specific locations of the products in accordance with prescribed sampling procedures; any warranty thereof is limited to the values obtained at such locations and by such procedures. There is no warranty with respect to values of the materials at other locations.

AK Steel and the AK Steel logo are registered trademarks of AK Steel Corporation. 11.20.15