44766 centre court (586) 226-1500 - pts-mi.com commercial... · refer to tool flyer for a complete...
TRANSCRIPT
44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail [email protected]/ www.gagebilt.com
ToolOpen End
NailMuti-GripStructural T Monobolt® Plastic Split Klamptite®
Bulbtite® Floor-Tight ClosedEnd
GBP703E 3/32"-3/16" 1/8"-3/16" 1/8"-3/16" 3/16" 1/4" - X 1/8"-3/16"GBP713C - - - - - - X -GBP724A - - - - - 1/4" X -GBP743C 1/4"-5/16" 1/4" 1/4" 1/4" - - X 1/4"*GBP2480 3/16" 1/4" 1/4" 1/4" 1/4" 1/4" X 1/4"
*GBP4801B X 3/8" X X X X 5/16" X
Tool Multi-Grip Lockbolt Lockbolt
BlindOversizedMandrel
Container Bolt C50L Huck Fit® HP8 MHP10.9
GBP713C 1/4" - X 3/8" X X X XGBP745D 5/16" 5/16"-3/8" Alloy 1/4" - X X X XGBP752E 3/16" 3/16"-1/4" X X X X X X*GBP2480 3/16"-1/4" 5/32-"1/4" 1/4" 3/8" X X X X
*GBP4801B 3/8" 5/16"-3/8" 5/16"-3/8" - X X X X*GBP585 X X X X X X X 16mm-20mm
*GBP7624B X X X X 1/2"-3/4" 1/2"-3/4" 1/2"-3/4" 12mm-16mm
Commercial Lockbolts
Fasteners To Tool Recommendation Chart********* Tool recommended is the most cost effective solution *********
Commercial Blind Rivets
"-" indicates the tool will install that fastener but is not the most cost effective solution.
*RECOMMENDED FOR HIGH PRODUCTION APPLICATIONS. GBP940 (ELECTRIC) OR GBP910C (AIR) POWERUNIT IS REQUIRED. 9/08
GAGE BILT……………………….……..committed to solutions
All tools will install a variety of fasteners. Refer to tool flyer for a complete list of fasteners that the tool will install.
MOST TOOLS AVAILABLE WITH PISTOL GRIP (SH) AND IN-LINE SPLIT SYSTEMS (SR) AND/OR VACUUM COLLECTOR SYSTEMS.
"X" indicates the tool is not recommended for that fastener.
9/08
Tool NAS9301-NAS9312
NAS1919S & UNAS1921S & U
MS21140S & UMS21141S & U
NAS1398NAS1399NAS1738NAS1739
NAS1398ANAS1399A NUTPLATE GROUND
STUD
NAS1719NAS1720NAS1721
MBC
2 ASPASP FFASP F
ASP LCGB51 1/8" 1/8" X X 3/32"-1/8" 3/32"-1/8" X 3/32"-1/8" X
GBP751D - 5/32"-3/16" 5/32" X 5/32"-3/16" - -8 5/32"-3/16" 13/64"GBP704F 5/32"-3/16" - - X - - - - -GBP713C - 1/4" 1/4" X 1/4" - - 1/4" 21/64"GBP745D - - 5/16" X - X - 1/4" -GBP752E 1/4" - 3/16" - - - -10 - 17/64"GBP784B X X X 1/8"-1/4" X X X X X*GBP2480 1/8"-1/4" 1/8"-1/4" 5/32"-1/4" X 3/32"-1/4" 3/32"-1/8" -8 & -10 3/32"-1/4" 13/64"-21/64"
*GBP4801B - - 5/16"-3/8" X - - - - -**GBP204 - - - X - X - - -**GBP205 X X - X X X X X X**GBP7XX - - - X - - - - -**GBP5XX X X - X X X X X X
Aerospace Blind Rivets
"-" indicates the tool will install fastener but is not the most cost effective solution.
GBP204 AND GBP205 HYDRAULIC INSTALLATION TOOLS ARE RECOMMENDED FOR OFFSET AND CLOSED ACCESS APPLICATIONS.
GAGE BILT……………………….……..committed to solutions
All tools will install a variety of fasteners. Refer to tool flyer for a complete list of fasteners that the tool will install.
MOST TOOLS AVAILABLE WITH PISTOL GRIP (SH) AND IN-LINE SPLIT SYSTEMS (SR) AND/OR VACUUM COLLECTOR SYSTEMS.
"X" indicates the tool is not recommended for that fastener.
Fasteners To Tool Recommendation Chart******** Tool recommended is the most cost effective solution ********
Tool
Lightweight Groove Proportioned Lockbolt
Groove Proportioned Lockbolt
Metric Lightweight Groove Proportioned Lockbolt
Metric Groove Proportioned Lockbolt
NASTENSION
NASSHEAR
GBP731 1/8"-1/4" 1/8"-1/4" 4mm-5mm 4mm-6mm 1/8"-1/4" 1/8"-1/4"GBP745D 5/16" 1/4"-5/16" 6mm-8mm 6mm-8mm 1/4"-5/16" 1/4"-5/16"*GBP2480 1/8"-1/4" 1/8"-1/4" - 4mm-6mm 1/8"-1/4" 1/8"-1/4"
*GBP4801B 5/16"-3/8" 5/16"-3/8" 8mm-10mm 8mm-10mm 5/16"-3/8" 5/16"-3/8"**GBP204 - - - - - -**GBP205 - - - - - -
GBP204 AND GBP205 HYDRAULIC INSTALLATION TOOLS ARE RECOMMENDED FOR OFFSET AND CLOSED ACCESS APPLICTIONS
Aerospace Lockbolts
*RECOMMENDED FOR HIGH PRODUCTION APPLICATIONS. GBP940 (ELECTRIC) OR GBP910A (AIR) POWERUNIT IS REQUIRED.
GAGE BILT………riveting solutions
GAGE BILT GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
*Most straight noses are available in short, medium and long lengths. 1) Contact Gage Bilts’ Engineering department for specific tool information. 9/08
Fasteners to Tools Selection Chart (Commercial Lockbolts)
3/16" GBP752E MG06-722-20 1 1
1/4" GBP713C MG08-713-20 1 1
5/16" GBP745D MG10-756-28 1 1
3/8" GBP4801B MG12-756-28 1 1
3/16" GBP752E LB06-722-20 1 1
1/4" GBP752E LB08-722-20 1 1
5/16" GBP745D LB10-745C-26 1 NAS10-205A-31
3/8" GBP745D LB12-756-26 1 NAS12-205A-31
1/4" GBP745D BOM08-745C-23 1 1
5/16" GBP4801B BOM10-756-26 1 1
3/8" GBP4801B BOM12-756-26 1 1
1/2" GBP7624B 16-7624-40 NONE NONE
5/8" GBP7624B 20-585-41 NONE NONE
3/4" GBP7624B 24-585-46 NONE NONE
1/2" GBP7624B HP16-7624-40 NONE NONE
5/8" GBP7624B HP20-585-41 NONE NONE
3/4" GBP7624B HP24-585-46 NONE NONE
12mm GBP7624B HP12MM-7624-40 NONE NONE
16mm GBP7624B HP20-585-41 NONE NONE
20mm GBP585 HP20MM-585-46 NONE NONE
NONE
353205 FOROFFSET NOSES
ADAPTER
ADAPTER
*STRAIGHTNOSE ASSEMBLY
C50L NONE
FASTENERTYPE
FASTENERDIAMETER
INSTALLATIONTOOL
*STRAIGHTNOSE ASSEMBLY ADAPTER
FASTENERTYPE
RIGHT ANGLENOSE ASSEMBLY
FASTENERDIAMETER
INSTALLATIONTOOL
NONEBOM
RIGHT ANGLENOSE ASSEMBLY
RIGHT ANGLENOSE ASSEMBLY
OFFSETNOSE ASSEMBLY
ADAPTER
OFFSETNOSE ASSEMBLY ADAPTER
FASTENERDIAMETER
INSTALLATIONTOOL
*STRAIGHTNOSE ASSEMBLY
FASTENERTYPE
FASTENERDIAMETER
HP8
*STRAIGHTNOSE ASSEMBLY
Multi Grip Lockbolt
RIGHT ANGLENOSE ASSEMBLY
OFFSETNOSE ASSEMBLY
FASTENERTYPE
FASTENERDIAMETER
INSTALLATIONTOOL
RIGHT ANGLENOSE ASSEMBLY
OFFSETNOSE ASSEMBLY
FASTENERTYPE
NONE
*STRAIGHTNOSE ASSEMBLY
NONE
RIGHT ANGLENOSE ASSEMBLY
OFFSETNOSE ASSEMBLY
FASTENERTYPE
Lockbolt
INSTALLATIONTOOL
FASTENERDIAMETER
OFFSETNOSE ASSEMBLY
ADAPTER
MHP10.9
INSTALLATIONTOOL
*STRAIGHTNOSE ASSEMBLY
GAGE BILT………riveting solutions Fasteners to Tools Selection Chart
(Commercial Blind Rivets)
GAGE BILT *Most straight noses are available in short, medium and long lengths. 1) Contact Gage Bilts’ Engineering department for specific tool information. 9/08
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
3/32" GB51 3N-715E-43 3N-715-54RA 3N-715-40OS
1/8" GB51 4N-715E-43 4N-715A-44 4N-715A-40OS
5/32" GBP703E 5N-743-20 1 1
3/16" GBP703E 6N-743-20 1 1
1/4" GBP743C 8N-743A-24 1 1
3/16" GBP703E MB06-734A-20 1 1
1/4" GBP743C MB08-734A-20 1 1
3/16" GBP703E 6T-743-20 1 1
1/4" GBP743C 8T-743A-24 1 1
3/32" GB51 3N-715E-43 3N-715-54RA 3N-715-40OS
1/8" GB51 4N-715E-43 4N-715-54RA 4N-715-40OS
5/32" GBP703E 5N-743-20 2 5N-352A-54RA 1
3/16" GBP703E 6N-743-20 2 6N-352A-54RA 1
1/4" GBP743C 8N-743A-24 1 1 NONE
3/16" GBP724A 6KT-743A-24 1 1
1/4" GBP724A 8KT-743A-24 1 1
3/16" GBP703E 6P-743-20 1 1
1/4" GBP703E 8P-743-20 1 1
Avseal 10mm GBP752E ASM10-752-21 1 1 NONE
3/16" GBP703E PH6-734A-20 1 1
1/4" GBP743C PH8-734-20 1 1
FloorTight 5/16" GBP4801B FT10-745B-26 1 1 NONE
Container 3/8" GBP713C HT12-713-20 1 1 NONE
PlasticSplit NONE
RIGHT ANGLENOSE ASSEMBLY
OFFSETNOSE ASSEMBLY
NONE
ADAPTERFASTENER
TYPEFASTENERDIAMETER
INSTALLATIONTOOL
2 703352
NONE
FASTENERTYPE
FASTENERDIAMETER
INSTALLATIONTOOL
*STRAIGHTNOSE ASSEMBLY
RIGHT ANGLENOSE ASSEMBLY
Closed End
Multi-GripStructural
*STRAIGHTNOSE ASSEMBLY
OFFSETNOSE ASSEMBLY
OFFSETNOSE ASSEMBLY
NONE
*STRAIGHTNOSE ASSEMBLY
RIGHT ANGLENOSE ASSEMBLY
OFFSETNOSE ASSEMBLY
NONE
FASTENERDIAMETER
FASTENERTYPE
OFFSETNOSE ASSEMBLY
ADAPTER
ADAPTER
RIGHT ANGLENOSE ASSEMBLY
OFFSETNOSE ASSEMBLY ADAPTER
NONE
ADAPTER
NONE
FASTENERTYPE
FASTENERDIAMETER
INSTALLATIONTOOL
*STRAIGHTNOSE ASSEMBLY
ADAPTER
ADAPTER
INSTALLATIONTOOL
*STRAIGHTNOSE ASSEMBLY
*STRAIGHTNOSE ASSEMBLY
INSTALLATIONTOOL
RIGHT ANGLENOSE ASSEMBLY
FASTENERTYPE
FASTENERDIAMETER
INSTALLATIONTOOL
FASTENERDIAMETER
*STRAIGHTNOSE ASSEMBLY
RIGHT ANGLENOSE ASSEMBLY
OFFSETNOSE ASSEMBLY
ADAPTEROFFSETNOSE ASSEMBLY
FASTENERTYPE
FASTENERTYPE
FASTENERDIAMETER
INSTALLATIONTOOL
*STRAIGHTNOSE ASSEMBLY
Open EndNail
FASTENERTYPE
FASTENERDIAMETER
RIGHT ANGLENOSE ASSEMBLY
RIGHT ANGLENOSE ASSEMBLY
Monobolt
Klamptite
T Rivet
INSTALLATIONTOOL
XX-204 SERIES NOSE ASSEMBLIES TO TOOL MODELS: G83A & G84A
*Tool Model Revision or Above
XX-701, XX-704, XX-753 & XX-763 Series Nose Assemblies to Tool Models: GBP744E*
XX-204 Series Nose Assemblies to Tool Models: GBP730E*, GBP751C*, GBP731, GBP722 & GBP713C*
XX-701, XX-704, XX-753 & XX-763 Series Nose Assemblies to Tool Models:GBP730E*, GBP751C*, GBP752E*, GBP731, GBP722, GBP713C* & GBP2480
XX-715B & XX-51 Series Nose Assemblies to Tool Models: GBP784B*
840204
784715
745751 3/4" Series Nose Assemblies to Tool Models: GBP745D*, GBP4801B* & GBP4804
456MAX-749-35 (Straight), 456MAX-704-43OS (Offset) & 456MAX-753A-54 (Right Angle) Nose Assemblies to Tool Models: GBP784B*
Extends XX-715B & XX-51 Series Nose Assemblies 2"
XX-715B & XX-51 Series Nose Assemblies to Tool Models: GBP752E*, GBP730E*, GBP731, GBP722 & GBP713C*
XX-715B & XX-51 Series Nose Assemblies to Tool Models: GBP740A*
Extends XX-704, XX-704, XX-753 & XX-763 Series Nose Assemblies 12"
Extends XX-703, XX-743 & XX-743 Series Nose Assemblies 6"
3/4" Series Nose Assemblies to Tool Models: GBP703E*, GBP724* & GBP743C*
XX-715B & XX-51 Series, Nose Assemblies to Tool Models: GBP704F*
Extends XX-704, XX-704, XX-753 & XX-763 Series Nose Assemblies 2"
Extends XX-703, XX-734 & XX-743 Series Nose Assemblies 2"
744704
751204
751704
704005
715002
Extends XX-704, XX-704, XX-753 & XX-763 Series Nose Assemblies 4"
Extends XX-704, XX-704, XX-753 & XX-763 Nose Assemblies 6"
730715
740715
704004
704006
704006-2
703006
703352
704001
704002
353205
353206
703002
GAGE BILT Tool Adapters
Adapter Adapts Nose Assembly To Tools
352704 XX-701, XX-704, XX-753 & XX-763 Series Nose Assemblies to Tool Models: 352, G83 & G84
XX-205 Series Nose Assemblies to Tool Models: GBP745D* & GBP4801B*
XX-206 and Huck 99-1700 & 99-3700 Series Nose Assemblies to Tool Models: GBP745C* & GBP4801B*
200
Nose Assembly Data Sheet Key
LB indicates a nose assembly for lockbolts. 08 is the fastener size (in 32nds of an inch, LB08-713-20 8/32”=1/4”).
713 is the tool it may be used on. This is not the only tool. Most nose assemblies may be used on a variety of tools.
20 is the approximate length, or “gun line”, from the tool in tenths of inches. In this case, 2.0 inches
Prefix codes refer to the type of fastener: A -“A” Code Rivet LB -Lockbolt LGP -Lightweight Groove Proportioned MAX -M7885/NAS9301-9312 MB -Monobolt MG -Multi-Grip Lockbolt MGL -Multi-Grip Blind Fastener MGP -Metric Groove Proportioned MLGP -Metric Lightweight Groove Proportioned N -Nail or Pop Rivet NAS -NAS Tension or Shear Lockbolt SB -Single Action Blind Bolt SMLS -NAS1919S & 1921S UBR -NAS1919U & 1921U
GAGE BILT…... fastening solutions for the 21st century
HOW A RIVET WORKSAs the trigger is pulled, hydraulic pressure in the tool forces the piston and collet to begin
to retract (figure 5). As this action first occurs, the jaws do not retract, instead they arecontinually forced forward by the jaw spring and follower. As the collet further retracts, the jawsare pulled back away from the nose tip. As this opposing movement occurs, the cone angle in thecollet causes the jaws to close onto the rivet pintail.
Once the jaws have a firm grip on the pintail (figure 6), the pulling action on the pintail pullsthe pintail head into the core of the rivet body causing the rivet body to expand. As this movementcontinues, the pintail head reaches a certain resistance that is greater than that of the break-neck.At this point, a strong, tight joint is formed. The pintail breaks away and the rivet is set. (Figure7)
When the trigger is released, the piston, collet, jaws, jaw spring, and jaw follower arereturned forward by air pressure to their full forward position. The jaws still grip the broken pintailuntil they contact the back of the nose tip. They are then forced open and release the pintail.Vacuum (if equipped) then pulls the broken pintail out of the nose assembly.
GAGE BILTGAGE BILT PRODUCTS CORP.
44766 Centre Court (586) 226-1500 Clinton Twp., Mi 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
Magna-Lok (Huck Ultra-Grip (POP)
Hemlock
Nail Rivet (open end) Avdel-Cherry (N)
‘T’ Rivet / Peel Rivet
Monobolt (Avdel)
Closed End Rivet
Avtainer / Hucktainer(Container Bolt)
C6L / AvdelokMagna-Grip (Huck) / Maxlock (Avdel)
BOM
Av-Seal / Av Plug Floortite
Klamp-Tite Bulb-Tite
Sleeve Bolt XXX
GO TO:www.gagebilt.com
FOR FLYERS, NOSE ASSEMBLIESAND RECOMMENDATIONS
FOR INDIVIDUAL APPLICATIONS
LOCKBOLT INSTALLATION TOOLS FOR THE RAILROAD INDUSTRY
SINCE 1956
GAGE BILT
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
GAGE BILTMADE IN U.S.A.
LOCKBOLT INSTALLATION TOOLING
The GBP585 is a hydraulic installation tool capable of installing 5/8" and 3/4" C50L or HP8 lockbolts. It weighs just under 20 lbs. and is our most powerful hand tool. It has a 1.600" rivet setting stroke and a rated pull load of 40,000 lbs. The GBP585 operates on GAGE BILT and HUCK® air or electric powerunits NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDERED SEPARATELY.
GBP585/GBP585AThe GBP745D is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range of blind rivets, lockbolts and MAGNA-GRIP® fasteners. It weighs just over 7 lbs. and can be operated in any position with one hand. It has a .600" rivet setting stroke and a rated pull load of 6300 lbs. with 90 psi air pressure at the air inlet. NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDERED SEPARATELY.
GBP745DThe GBP7264B is a hydraulic installation tool capable of installing 1/2", 5/8" and 3/4" C50L or HP8 lockbolts. It weighs 15 lbs and can be operated in any position with one hand. It has a 1.970" rivet setting stroke and a rated pull load of 40,000 lbs.. The GBP7624B operates on GAGE BILT and HUCK® air or electric powerunits NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDERED SEPARATELY.
GBP7624B/GBP7624B(A)
GBP4801B/GBP4801B(A)The GBP4801B is a hydraulic installation tool designed specifically for the efficient installation of a wide range of lockbolt and Magna-Grip fasteners thru 3/8" diameter. It weighs just under 8 lbs. and can be operated in any position with one hand. It has a 1.000" rivet setting stroke and a rated pull load of 11,000 lbs.. The GBP4801B operates on GAGE BILT and HUCK® air or electric powerunits. NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDERED SEPARATELY.
GBP2480/GBP2480AThe GBP2480 is a hydraulic installation tool designed specifically for the efficient installation of a wide range lockbolts and Multi-Grip fasteners thru 1/4" diameter. It weighs just over 3 lbs. and is operated in any position with one hand. It has an .875 rivet setting stroke and rated pull load of 5600 lbs. The GBP2480 operates on GAGE BILT and HUCK® air or electric powerunits. NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDERED SEPARATELY.
POWERUNITS
AIR, ELECTRIC & FOOT OPERATED
9/08
GBP940
GBP910D
GBP902
GAGE BILT Lockbolt and blind rivet installation tools Fastening solutions for the 21st century
GAGE BILT PRODUCTS CORP. 44766 Centre Ct. Clinton Twp MI 48038 E-mail: [email protected] Phone (586) 226-1500 www.gagebilt.com Fax (586) 226-1505
ORDER INFORMATION
1. Minimum net order: U.S. = 75.00; Outside U.S. = $125.00
2. F.O.B: Clinton Township, MI
3. Terms: Net – 30 days
4. There is a $75.00 minimum or 20% whichever is greater, restocking charge.
5. Shortages must be reported within 48 hours of delivery.
6. 24 hour/expedited service is available on most nose assemblies and tool. There is a $75.00 minimum or 10%, whichever is greater, additional charge.
7. ALL PRICES ARE SUBJECT TO CHANGE WITHOUT NOTICE.
8. Drawings of all noses assemblies, installation tools and powerunits are available at www.gagebilt.com or call “inside sales” for specific information.
WARRANTY
Seller warrants that all goods covered by this catalog will conform to applicable specificationsand drawings and will replace, or repair, F.O.B. our plant, any goods proving defective from faultyworkmanship, or material, for 90 days from date of shipment.
Said warranty to remain in effect if and only if such goods are used in accordance with allinstructions as to maintenance, operation, and use set forth in manuals and instruction sheets furnishedby Seller.
Seller's obligation under this warranty shall be limited to the repair or rework of the goodssupplied or the replacement thereof, at Seller's option, and in no case is to exceed the invoice value ofsaid goods. Under no circumstances will Seller be liable for incidental or consequential damages or for damages incurred by the buyer or subsequent user in repairing or replacing defective goods or ifgoods covered by this warranty are reworked or subjected to any type of additional processing.
This warranty is void if Seller is not notified in writing of any rejections or defects within 90 days after receipt of the material by customer.
THIS WARRANTY IS MADE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS ORIMPLIED, INCLUDING MERCHANTABILITY.
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
GAGE BILTMADE IN U.S.A.
6.272.64 Ø
7.31
GB51PNEUMATIC INSTALLATION TOOL
DESCRIPTION
The GB51 pneumatic riveter is designed specifically for the most efficient installation of a wide range ofblind rivets. It will install aluminum rivets through 3/16" diameter, and through 1/8" diameter rivets in anymaterial. It weighs only 2 1/2 lbs. and can be operated in any position with one hand.
The GB51 Riveter is 7" high, has a .740 stroke and generates a minimum of 1000 lbs. of pull at 90 psi. Itoperates from 80 to 110 psi of air pressure at the tool.
NOSE ASSEMBLIES ARE NOT FURNISHED WITH THIS TOOL AND MUST BE PURCHASED SEPARATELY.
FASTENER DIA. STRAIGHT RIGHT ANGLE 1, 6 OFFSET 3/32 3C-715B-43 3C-715-54RA 3C-715-40OS
1/8 4C-715B-43 4C-715-54RA 4C-715-40OS
5/32 3 5C-715B-43 5C-715-54RA 5C-715-40OS
3/16 3 6C-715B-43 6C-715-54RA 6C-715-40OS3/32 3A-715B-43 3A-715-54RA 3A-715-40OS1/8 4A-715B-43 4A-715-54RA 4A-715-40OS
5/32 3 5A-715B-43 5A-715-54RA 5A-715-40OS3/16 5 6A-715B-43 6A-715-54RA 6A-715-40OS1/8 SMLS04-715B-43 SMLS04-715-54RA SMLS04-715A-40OS
5/32 3 SMLS05-715B-43 SMLS05-715-54RA SMLS05-715A-40OS3/16 3 SMLS06-715B-43 SMLS06-715-54RA SMLS06-715A-40OS
1/8 5/32 3
3/16 3
3/32 3N-715E-43 3N-715-54RA 3N-715-40OS1/8 4N-715E-43 4N-715-54RA 4N-715-40OS
5/32 3 5N-715E-43 5N-715-54RA 5N-715-40OS3/16 3 6N-715E-43 6N-715-54RA 6N-715-40OS
1) RIGHT ANGLE NOSE ASSEMBLYS MAY REQUIRE MORE THAN ONE PULL.2) INSTALLS 1/8, 5/32 & 3/16 DIAMETERS.3) ALUMINUM ONLY.4) ALUMINUM & STEEL ONLY.5) SELF-PLUGGING ALUMINUM ONLY6) RIGHT ANGLE NOSE ASSEMBLYS REQUIRE 510152 STROKE LIMITER.
NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTS THE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES
NUT PLATE RIVETSMS20600 SERIESCCR244/264/274
MS/9SP/PTBACR15CC/CF/DA/DR
"A" CODENAS1398A, NAS1399ANAS1740A, NAS1739A
SINGLE ACTION BLIND RIVETNAS1919S & UNAS1921S & U
456MAX-715-43 2
THE GAGE BILT GB51 TOOL IS APPROVED TO INSTALL THE ABOVE FASTENERS.
*ALL COUNTERSUNK 'C' NOSE ASSEMBLIES MAY BE USED TO INTSALL BOTH UNIVERSAL & COUNTERSUNK HEAD RIVETS
456MAX-715A-54RA 2 456MAX-715-40OS 2
N, Q & EPOP®, CLOSED END
AVEX® & COMMERCIAL RIVETS
BACR15FR/FP, BACR15GF/GK,NAS1919S & U & NAS1921S & U
"U" TYPE BLIND RIVET WITH LOCKING WASHER
NAS9301-9312
GB51 SELECTION CHART
Rev.11/08
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
GAGE BILTMADE IN U.S.A.
GB8000 SERIESAUTO FEEDER
Gage Bilts’ 8000 series semi-automated riveting systems use a hand held pistol grip or an in-lineinstallation tool. The tool comes with a 8 foot umbilical connected to a hydraulic power unit. Thetool and power unit work cooperatively with a vibratory bowl, escapement and plc controller builtinto a base unit of 28"x16"x14". The unit automatically presents rivets to the nose tip from thefeeder with air. The rivet is then pulled into the tool via a vacuum system that also provides forthe discharge of the spent pintails. The unit requires 110 vac, 80 psi minimum, with 10 CFM ofcompressed air. This system is capable of a feed rate of 45 rivets a minute. Contact ourengineering department for specific applications. A video of this system is available atwww.gagebilt.com.
TRIGGER
NOSEASSEMBLY
NOSETIP
NESTASSEMBLY
FEEDER ARMASSEMBLY
VACUUMTUBE
VIBRATORYBOWLFEED TRACKS AND
ESCAPEMENT
FRONT OF BASEAND FRAME
FILTER REGULATORASSEMBLY
BOOSTERVALVE
ASSEMBLY
ELECTRICALENCLOSURE VACUUM
COLLECTION
Rev. 1/07
11.27
4.48
4.38 Ø
.91
4.31
2.552.07 Ø
2.81 Ø
G A G E B IL TMA DE IN U.S.A .
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
GBP585HYDRAULIC INSTALLATION TOOL
DESCRIPTION
The GBP585 is a hydraulic installation tool capable of installing 5/8" and 3/4" HP8 or standardlockbolts. It weighs just under 20 lbs. and is our most powerful hand tool. It has a 1.600" rivetsetting stroke and a rated pull load of 40,000 lbs.
The GBP585 installation tool operates on hydraulic pressure developed by the GBP940 Powerunitset at 5400-5700 psi PULL pressure and 2200-2400 psi RETURN pressure. The tool comesequipped with 24" hoses and electric cord kit complete with quick disconnects.
NOSE ASSEMBLIES ARE NOT FURNISHED WITH THE RIVETER AND MUST BE ORDEREDSEPARATELY.
20-585-41
GBP585 SELECTION CHART
FASTENER DIA. NOSE ASSEMBLY
LOCKBOLT HIGH TENSILE PULL TYPE 5/8 20-585-41C5OL 3/4 24-585-46
BLIND OVERSIZE MANDREL 5/8 BOM20-585-413/4 BOM24-585-46
HP8 5/8 HP20-585-41
3/4 HP24-585-46
MHP 10.9 16MM HP20-585-41 * 20MM 1 HP20MM-585-46
*FOR NON-PRODUCTION APPLICATIONS ONLY 1) POWER UNIT REQUIRES ADJUSTMENT TO 7,200 PSI FOR PULL AND 4,000 PSI FOR RETURN
NOSE ASSEMBLY KEY
20-585-41
A ~The first numerical digit represent the diameter of the fastener in 32nds of an inch. (20/32)
B ~The second set of digits represent ONE of the tool models which MAY be used with this head. (Model 585)
C ~The last set of numerical digits signify the “Gun Line”, or reach of the pulling head to the nearest tenth of an inch. (41 is 4.1 inch “Gun Line”)
GBP585 SELECTION CHART
*FOR NON-PRODUCTION APPLICATIONS ONLY 1) POWER UNIT REQUIRES ADJUSTMENT TO 7,200 PSI FOR PULL AND 4,000 PSI FOR RETURN
pulling head to the nearest tenth of an inch. (41 is 4.1 inch “Gun Line”)
Rev. 4/07
GBP585MFK Millimeter Framebolt Kit Installs HUCK® 10.9 and Metric Huck-Fit® Truck Framebolts
INCLUDES: GBP902-12 air operated manual Hydraulic Powerunit with 12’ hoses.
GBP585ANT Hydraulic Installation Tool. HP12MM-7624-40 – 12mm Nose Assembly.
HP20-585-41 – 16mm Nose Assembly. HP20MM-585-46 – 20mm Nose Assembly.
9/08
GAGE BILTMADE IN U.S.A.
CAUTION: Always consult tool manual before resetting any pressures. The air pressure to the unit controls the output and return pressure to the tool and must be properly adjusted for each tool. If pressures are not adjusted properly severe personal injury may result.
GAGE BILT is now offering a new product for truck and trailer repair facilities, the GBP585MFK. It’s a low cost solution for frame repair. The GBP585MFK incorporates GAGE BILTS’ new GBP902 air operated powerunit. Just plug it into shop air and you’re ready to put in HUCK 12mm, 16mm and 20mm 10.9 metric Huck-Fit® truck framebolts. The nose for the 16mm also installs Huck HP8 5/8” framebolts in your Pete or KW. The GBP585ANT installation tool is included, as well as a 12’ hose kit. The power unit is a manual foot pedal operated hydraulic power source that delivers 5,700 psi pull and return pressure with 65 psi air pressure connected to the power unit and is adjustable for higher pressures.
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp, MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
GB585MTFK Installation Kit Installs HUCK® 10.9 and Huck-Fit Truck Frame Bolts
INCLUDES: GBP910C-12 air operated Hydraulic Powerunit with 12’ hoses.
GBP585A Hydraulic Installation Tool. HP12MM-7624-40 – 12mm Nose Assembly.
HP20-585-41 – 16mm Nose Assembly. HP20MM-585-46 – 20mm Nose Assembly.
GAGE BILT9/08
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. Mi 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
GAGE BILTMADE IN U.S.A.
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
9.82(249.4mm)
4.15(105.3mm)
5.07(128.7mm)
4.04
5.07(128.7mm)
1.90(48.2mm)
4.12(104.6mm)
1.56 Ø(39.6mm)
1.78(45.2mm)
1.25(31.75mm)
3.88 Ø(98.5mm)
1.14 Ø(28.9mm)
2.17(55.1mm)
6.19(157.1mm)
8.10(205.8mm)
.87(22.1mm)
7.08[179.75mm]
GBP703E SERIES INSTALLATION TOOLS
GBP703EStroke - .780"Hand held weight - 4.50 lbs.Entire tool weight - 4.50 lbsPull load - 2,200
GBP703ESRStroke - .780"Hand held weight - 1.50 lbs.Entire tool weight - 4.50 lbsPull load - 2,200
GBP703ESHStroke - .800"Hand held weight - 2.00 lbs.Entire tool weight - 7.25 lbsPull load - 2,200
RIVET DIA. NOSE ASSEMBLY NOSE TIP 1 JAW FOLLOWER DESIGNATION3/16 AV6-743A-24 2 10141 30849 40871 AV63/16 6C-743A-24 2 10141-1 30849 40871 6C
3/16 6KT-743-20 1 10263 30537 40605 6KT
1/4 8KT-743A-24 2 10262 30849 40871 8KTMACHINE SCREW RIVET 5MM MS5M-743-20 1 10332 30537 40605 5MM
3/16 MB06-734A-20 2,5 10210 36801 48808 MB06
1/4 3 MB08-734-20 2,5 10213 30833 48808 MB08
3/32 3NP-743-20 1 10231 30537 40307 3NP
1/8 5N-743-20 1 10203 30537 40605 5N
3/32 3N-743-20 1 10201 30537 40307 3N
1/8 4N-743-20 1 10202 30537 40307 4N
5/32 5N-743-20 1 10203 30537 40605 5N3/16 6N-743-20 1 10204 30537 40605 6N1/4 3 8N-743A-24 2 10211 30849 40871 8N
3/32 3P-743-20 1 10247-1 30537 40307 3P1/8 4P-743-20 1 10202-4 30537 40307 4P5/32 5P-743-20 1 10203-2 30537 40605 5P3/16 6P-743-20 1 10167 30537 40605 6P1/4 8P-743A-24 2 10166 30849 40871 8P3/16 6T-743-20 1 10209 30537 40605 6T1/4 3 8T-743A-24 2 10286 30849 40871 8T
TLR RIVET 1/4 8TLR-743A-24 2 10246 30849 40871 8TLR
RIVET DIA. NOSE ASSEMBLY NOSE TIP 1 JAW FOLLOWER DESIGNATION3/16 PH6-734A-20 2,5 10248 36801 48808 PH6
1/4 4 PH8-734-20 2,3,5 10205 30833 48808 PH8
2) NOSE ASSEMBLIES WITH A 743-24 DESIGNATION, I.E. 8N-743A-24, MUST BE ORDERED AS COMPLETE NOSE ASSEMBLY.3) ALUMINUM RIVET STEEL MANDREL ONLY (100 PSI REQUIRED FOR ALL 1/4" STEEL RIVETS).4) 1/4" ALUMINUM ONLY.5) NOSE ASSEMBLIES WITH A 734 DESIGNATION, I.E. PH6-734-20, ARE FOR SERRATED STEM RIVETS ONLY. IF YOU ARE PULlING BOTH SMOOTH AND SERRATED STEM RIVETS YOU MUST ORDER THE NOSE ASSEMBLY WITH A 743 DESIGNATION, I.E. MGL06-743-24.
PLASTIC SPLIT RIVET
MONOBOLT RIVET
NUTPLATE RIVETCCR244/264/274
BACR15DRMS20600
AVEX (1624 PROTRUDING HEAD)AVEX (1624COUNTERSUNKHEAD)
OPEN ENDCLOSED ENDNAIL RIVET
KLAMPTITE (STRUCTURAL) RIVET
EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES
SERRATED STEM STRUCTURAL RIVET
NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTS THE LENGTH THE NOSE
T RIVET
1) YOU CAN CHANGE THE 743-20 NOSE ASSEMBLY (INCLUDED WITH TOOL) TO INSTALL OTHER FASTENERS BY PURCHASING NOSE TIP SHOWN AND USING APPROPRIATE FOLLOWER SHOWN.
SELECTION CHART FOR PROTRUDING HEAD ONLY
HOW TO ORDER GBP703 SERIES TOOLS
GBP703E SH V / 6N
TOOL SERIES
SH - SPLIT HANDLE MODELSR - SPLIT RIVETER MODEL
NO DESIGNATION - STANDARD MODEL
6N - RIVET SPECIFIC DESIGNATION(SEE SELECTION CHART)NO DESIGNATION - STANDARD
V - VACUUM W/ COLLECTOR BOTTLEVT - VACUUM W/ EVACUATION TUBENO DESIGNATION - NO VACUUM
GBP703E SERIES SELECTION CHART
“V” DESIGNATION = PINTAIL COLLECTOR BOTTLE “VT” DESIGNATION = PINTAIL EVACUATION TUBE
11/08
DESCRIPTION
The GBP703E series are pneumatic-hydraulic tools designed specifically forthe efficient installation of a wide range ofblind rivets. They can be operated in anyposition with one hand. They have a ratedpull load of 2200 pounds with 90 psi airpressure at the air inlet.
The GBP703ESH and GBP703ESR rivetersoffer a unique “split” system providing theoperator with an ergonomic tool withreduced hand held weight, as shownbelow.
The GBP703E series riveters operate on awide range of air pressure, with 90 to 100psi providing the maximum efficiency. At90 lbs air pressure, the GBP703E seriesdoes not exceed 85 db (A) and consumes 3cfm at 20 cycles a minute.
The GBP703E series riveters are furnishedwith nose assembly 6N-743-20 and sparenose tip 10202 and follower 40307 toconvert to 4N-743-20 nose assembly.
OPTIONS
The GBP703E series riveters may beordered with a vacuum system.Gage Bilt offers two varieties (see below)
Order GBP703E series riveters with theproper rivet specification by adding theappropriate suffix (see selection chart).
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp, MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
1.25(31.8mm)
3.88 Ø(98.6mm)
1.94 Ø(49.2mm)
1.36 Ø(34.5mm)
7.14(181.4mm)
4.33(110mm)1.80
(45.7mm)
1.92(48.8mm)
12.59(320mm)
5.16(131mm)
5.07(128.8mm)
GAGE BILTMADE IN U.S.A.
GBP722 INSTALLATION TOOL
DESCRIPTION
The GBP722 is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide rangeof blind rivets. It weighs 5.50 lbs. and can be operated in any position with one hand. It has a .590" rivetsetting stroke and a rated pull load of 4700 pounds with 90 psi air pressure at the air inlet.
The GBP722 riveter operates on a wide range of air pressure, with 90 to 100 psi providing the maximumefficiency. At 90 lbs air pressure, the GBP722 does not exceed 85 db (A) and consumes 3 cfm at 20 cyclesa minute.
The air inlet is provided with 1/4-18 female pipe threads to accept the users air hose fitting.
NOSE ASSEMBLIES ARE NOT FURNISHED WITH TOOL AND MUST BE ORDERED SEPARATELY.
FASTENER DIA. *RIGHT ANGLE 2
3/16 LB06-722-20 LB06-722-601/4 LB08-722-20 LB08-722-603/16 MG06-722-20 MG06-722-601/4 MG08-722-20 MG08-722-605/32 SB05-752B-20 SB05-752B-45 SB05-751B-54RA SB05-752A-43OS
SB05-752B-803/16 SB06-752B-20 SB06-752B-45 SB06-751B-54RA 5 SB06-204C-27OS
SB06-752B-801/4 4 SB08-713-20 4 SB08-713-45 4 SB08-204C-27OS 4 SB08-204C-37OS 4
5/32 UBB05-752B-20 UBB05-752B-45 UBB05-751B-54RA UBB05-752A-43OS
3/16 UBB06-752B-20 UBB06-752B-45 UBB06-751B-54RA 5 UBB06-752A-43OS
1/4 4 UBB08-713-20 4 UBB08-713-45 4 UBB08-204C-27OS 4 UBB08-204C-27OS 4
1/8 UAB04-752B-20 UAB04-752B-45 UAB04-751B-54RA UAB04-752A-43OS5/32 UAB568-713-21 3 UAB568-713-61 3 UAB05-751B-54RA UAB05-752A-43OS3/16 UAB06-751B-54RA 5 UAB06-752A-43OS1/4 UAB08-204C-27OS UAB08-204C-37OS
1/8 SMLS04-752B-20 SMLS04-752B-45 SMLS04-751B-54RA SMLS04-752A-43OS5/32 SMLS05-752B-20 SMLS05-752B-45 SMLS05-751B-54RA SMLS05-752A-43OS3/16 SMLS06-752B-20 SMLS06-752B-45 SMLS06-751B-54RA SMLS06-752A-43OS1/4 SMLS08-713-20 SMLS08-713-45 SMLS08-751B-54RA SMLS08-204C-27OS SMLS08-204C-37OS3/32 3A-352B-25 3A-751B-54RA1/8 4A-752B-20 4A-752B-45 4A-751B-54RA 4A-752A-43OS5/32 5A-752B-20 5A-752B-45 5A-751B-54RA 5A-752A-43OS3/16 6A-752B-20 6A-752B-45 6A-751B-54RA 6A-752A-43OS1/4 SMLS08-713-20 SMLS08-713-45 SMLS08-751B-54RA 5 SMLS08-204C-27OS SMLS08-204C-37OS3/16 MGL06-752A-21 6 MGL06-752A-61 6 MGL06-751B-54RA 61/4 MGL08-752A-21 6 MGL08-752A-61 63/16 6CN-752A-21 6 6CN-752A-61 61/4 8CN-752A-21 6 8CN-752A-61 63/16 MB06-752A-21 6 MB06-752A-61 6 MB06-751B-54RA 61/4 MB08-752A-21 6 MB08-752A-61 6
1/8 456MAX-751A-21 1 456MAX-751A-61 1 456MAX-751C-54RA 1 456MAX-752-42OS 1
5/32
3/16
1/4 08MAX-752B-20 08MAX-752B-45 08MAX-204C-27OS 08MAX-204C-37OS13/64 ASP06-752B-20 ASP06-752B-45 ASP06-751B-54RA ASP06-752A-43OS17/64 ASP08-752B-20 ASP08-752B-45 ASP08-751B-54RA ASP08-752A-43OS21/64 ASP10-713-20 ASP10-713-45 ASP10-204C-27OS ASP10-204C-37OS1/8 MBC04-752B-20 MBC04-752B-45 MBC04-751A-54RA MBC04-752A-43OS5/32 MBC05-752B-20 MBC05-752B-45 MBC05-751A-54RA MBC05-752A-43OS3/16 MBC06-752B-20 MBC06-752B-45 MBC06-751A-54RA MBC06-752-A43OS8/32 GS8-752B-20 GS8-752B-45 GS8-751B-54RA GS8-752A-43OS `
10/32 GS10-752B-20 GS10-752B-45 GS10-752A-54RA GS10-752A-43OS
2) RIGHT ANGLE NOSE ASSEMBLIES MAY REQUIRE MORE THAN ONE PULL.3) INSTALLS 5/32, 3/16 & 1/4 DIAMETERS.4) 105 PSI REQUIRED FOR ALLOY STEEL.
MS90353 & MS90354 MS21140 & MS21141
"U" TYPE BLIND BOLT WITH DRIVE WASHER
6) 2 PULLS REQUIRED FOR MOST APPLICATIONS.
EN6122 & UAB130-EUEN6127 & UAB6127-EUEN6128 & UAB100-EU
EN6129 & UABP-EU
**ALL OFFSET 204 SERIES NOSES REQUIRE 751204 ADAPTER.*ALL RIGHT ANGLE NOSE ASSEMBLIES REQUIRE 722140 STROKE LIMITER.
1) INSTALLS 1/8 5/32 & 3/16 DIAMETERS
3/8 HT12-713-20
THE GAGE BILT GBP722 IS APPROVED TO INSTALL THE ABOVE FASTENERS.
NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTSTHE LENGTH THE NOSE EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES
5) THESE NOSES FOR LIGHT DUTY / REPAIR ONLY.
GROUND STUD,M83454 & BACS53B
MS90353S & U & MS90354S & U MS21140S & U & MS21141S & U
CR7000 SERIES BACB30YY, YU, & YT
NAS1719, NAS1720NAS1721
PROTRUDING HEAD,MULTI-GRIP BLIND RIVETS
MONOBOLT
BACR15FR/FP, BACR15GF/GK,NAS1919 & NAS1921
"U" TYPE BLIND RIVET WITH DRIVE WASHER
NAS9301-9312
CONTAINER BOLT(R 12)HLPP, HLPM, HLPE, HLPS
HLPSC & HLPSM
COUNTERSUNK HEAD,MULTI-GRIP BLIND RIVETS
SINGLE ACTION BLIND RIVETNAS1919S & U NAS1921S & U
"A" CODENAS1398A & NAS1399A
ASP 2, ASP PF, ASP 4 FF,ASP 2 F, ASP 2 LC
STRAIGHT **OFFSET
COMMERCIAL LOCKBOLTS
MULTIGRIP LOCKBOLTS
SELECTION CHART FOR GBP722
Rev. 11/08
Introducing the GBP722TCK… Trailer and Cab Kit
Choose GAGE BILTS’ blind rivet and lockbolt installation kit designed especially for Truck and Trailer OEM’s. The GBP722TCK can be configured to meet your needs, whether you’re fixing Wabash, Great Dane, Peterbilt, Kenworth or any other brand trailer or truck. The kit includes nose assemblies to pull your fasteners, and at the heart of the system is our heavy-duty GBP722 installation tool. All of this is conveniently stored in a metal tool case.
The GBP722TCK kit comes with a nose and 2 tips to install 3/16” and 1/4” structural blind rivets in any material, a catcher bag for pintails, a 3/16” nose for the stainless steel grill bolt, and a 3/16” & 1/4” Magna-Grip® nose for the hood and cab. If additional noses are needed please consult Gage Bilt.
GAGE BILTMADE IN U.S.A.
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
Rev. 11/08
3/16"ALUMINUM, STEEL OR
STAINLESS STEEL MAGNA-LOK® BLIND RIVET
MGLC68-752A-21(USE 10248-4 NOSE TIP)
1/4"ALUMINUM, STEEL OR
STAINLESS STEEL MAGNA-LOK® BLIND RIVET
MGLC68-752A-21(USE 10211-1 NOSE TIP)
3/16" STAINLESS STEEL C6L
3/16" STEEL C6L
3/16" ALUMINUM C6L
3/16" STEEL MAGNA-GRIP®
3/16" ALUMINUM MAGNA-GRIP®
1/4" STEEL MAGNA-GRIP®
1/4" ALUMINUM MAGNA-GRIP®
Rev. 11/08
GBP722TCK
*NOSES LISTED PROTRUDE 2 INCHES FROM THE TOOL. LONGER NOSES ARE AVAILABLE.
BLIND RIVETS (2 PULLS REQUIRED FOR MOST APPLICATIONS)
LOCKBOLTS
LB06-722-20
MG06-722-20
MG08-722-20
LB06-722-20
MG06-722-20MG08-722-20
.750 Ø 2.230
MGL68-752A-21
1.950.750 Ø
2.000.750 Ø
2.000.750 Ø
1.25(31.8mm)
3.88 Ø(98.6mm)
5.07(128.7mm)
5.17(131.2mm)
1.92(48.8mm)
8.70(221.2mm)
6.77(717.9mm)2.92
(74.1mm)
.87 Ø(22.0mm)
1.84(46.7mm)
1.94 Ø(49.3mm)
1.36 Ø(34.5mm)
GAGE BILTMADE IN U.S.A.
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
7.40(188mm)
4.22(107mm)
GBP724A SERIES INSTALLATION TOOLS
GBP724AStroke - .688"Hand held weight - 5.5 lbs.Entire tool weight - 5.5 lbsPull load - 4,100
GBP724ASHStroke - .915"Hand held weight - 2.25 lbs.Entire tool weight - 6.5 lbsPull load - 4,100
GBP724ASRStroke - .688"Hand held weight - 1.75 lbs.Entire tool weight - 6 lbsPull load - 4,100
RIVET DIA. NOSE ASSEMBLY NOSE TIP JAW FOLLOWER DESIGNATION3/16 AV6-743A-24 1 10141 30849 40871 AV63/16 6C-743A-24 1 10141-1 30849 40871 6C1/4 BT08-743A-24 1 10391 30849 40871 BT089/32 BT09-743-24 1 10289 30824 40901 BT09
3/16 6KT-743A-24 1 10263 30849 40871 6KT
1/4 8KT-743A-24 1 10262 30849 40871 8KTMACHINE SCREW RIVET 5MM MS5M-743A-24 1 10332 30849 40871 5MM
3/16 MB06-734A-20 2,3 10210 36801 48808 MB06
1/4 MB08-734-20 2,3 10213 30833 48808 MB08
3/32 3N-743-20 2 10201 30537 40307 3N
1/8 4N-743-20 2 10202 30537 40307 4N
5/32 5N-743-20 2 10203 30537 40605 5N3/16 6N-743A-24 1 10204 30849 40871 6N1/4 8N-743A-24 1 10211 30849 40871 8N3/16 6P-743A-24 1 10167 30849 40871 6P1/4 8P-743A-24 1 10166 30849 40871 8P3/16 6T-743A-24 1 10209 30849 40871 6T1/4 8T-743A-24 1 10286 30849 40871 8T
TLR RIVET 1/4 8TLR-743A-24 1 10246 30849 40871 8TLR
RIVET DIA. NOSE ASSEMBLY NOSE TIP JAW FOLLOWER DESIGNATION3/16 PH6-734A-20 2,3 10248 36801 48808 PH6
1/4 PH8-734-20 2,3 10205 30833 48808 PH8
1) YOU CAN CHANGE THE 743 NOSE ASSEMBLY (INCLUDED WITH TOOL) TO INSTALL OTHER FASTENERS BY PURCHASING
2) NOSE ASSEMBLIES WITH A 743 AND 734 DESIGNATION, I.E. 5N-743-20, MUST BE ORDERED AS COMPLETE NOSE ASSEMBLY.3) NOSE ASSEMBLIES WITH A 734 DESIGNATION, I.E. PH6-734-20, ARE FOR SERRATED STEM RIVETS ONLY. IF YOU ARE PULlING BOTH SMOOTH AND SERRATED STEM RIVETS YOU MUST ORDER THE NOSE ASSEMBLY WITH A 743 DESIGNATION, I.E. MGL06-743A-24.
NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTS THE LENGTH THE NOSEEXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES
SERRATED STEM STRUCTURAL RIVET
PLASTIC SPLIT RIVET
NOSE TIP SHOWN AND USING APPROPRIATE FOLLOWER SHOWN.
T RIVET
SELECTION CHART FOR PROTRUDING HEAD ONLY
BULB-TITE (STRUCTURAL) RIVET
AVEX (1624 PROTRUDING HEAD)AVEX (1624COUNTERSUNKHEAD)
OPEN ENDCLOSED ENDNAIL RIVET
KLAMPTITE (STRUCTURAL) RIVET
MONOBOLT RIVET
GBP724A SH V / 8Z
TOOL SERIES
SH - SPLIT HANDLE MODELSR - SPLIT RIVETER MODEL
NO DESIGNATION - STANDARD MODEL
8Z - RIVET SPECIFIC DESIGNATION(SEE SELECTION CHART)NO DESIGNATION - STANDARD
V - VACUUM W/ COLLECTOR BOTTLEVT - VACUUM W/ EVACUATION TUBENO DESIGNATION - NO VACUUM
GBP724A SERIES SELECTION CHART
“V” DESIGNATION = PINTAIL COLLECTOR BOTTLE “VT” DESIGNATION = PINTAIL EVACUATION TUBE
Rev. 11/08
DESCRIPTION
The GBP724A series are pneumatic-hydraulictools designed specifically for the efficientinstallation of a wide range of blind rivets.They can be operated in any position withone hand. They have a rated pull load of 4100pounds with 90 psi air pressure at the airinlet.
The GBP724ASH and GBP724ASR rivetersoffer a unique “split” system providing theoperator with an ergonomic tool withreduced hand held weight, as shown below.
The GBP724A series riveters operate on awide range of air pressure, with 90 to 100 psiproviding the maximum efficiency. At 90 lbsair pressure, the GBP724A series does notexceed 85 db (A) and consumes 3 cfm at 20cycles a minute.
The GBP724A series riveters are furnishedwith nose assembly 8N-743A-24 and sparenose tip 10206 to convert to 6N-743A-24.
OPTIONS
The GBP724A series riveters may be orderedwith a vacuum system. Gage Bilt offers twovarieties (see below)
Order GBP724A series riveters with theproper specification by adding theappropriate suffix (see selection chart)
GAGE BILTMADE IN U.S.A.
GAGE BILTPRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
GBP743C SERIES INSTALLATION TOOLS9.00
(228.6mm)6.74(171.1mm)2.95
(74.9mm)
.87 Ø(22.1mm)
2.25(57.1mm)
6.17(156.7mm)
4.79(121.5mm)
4.88 Ø(123.9mm)
1.84(46.7mm)
1.50(38.1mm)
1.94 Ø(49.2mm)
1.36 Ø(34.5mm)
4.31(109.4mm)
7.40(188mm)
GBP743CStroke - .900"Hand held weight - 6.25 lbs.Entire tool weight - 6.25 lbsPull load - 4,200
GBP743CSRStroke - .900"Hand held weight - 1.75 lbs.Entire tool weight - 6.75 lbsPull load - 4,200
GBP743CSHStroke - .650"Hand held weight - 2.25 lbs.Entire tool weight - 7.25 lbsPull load - 4,200
HOW TO ORDER GBP743 SERIES TOOLS
GBP743C SH V / 8Z
TOOL SERIES
SH - SPLIT HANDLE MODELSR - SPLIT RIVETER MODEL
8Z - RIVET SPECIFIC DESIGNATION (SEE SELECTION CHART)NO DESIGNATION - STANDARD
V - VACUUM W/ COLLECTOR BOTTLEVT - VACUUM W/ EVACUATION TUBENO DESIGNATION - NO VACUUM
RIVET DIA. NOSE ASSEMBLY NOSE TIP JAW FOLLOWER DESIGNATION3/16 AV6-743A-24 1 10141 30849 40871 AV63/16 6C-743A-24 1 10141-1 30849 40871 6C1/4 BT08-743A-24 1 10391 30849 40871 BT08
9/32 BT09-743-24 1 10289 30824 40901 BT09
3/16 6KT-743A-24 1 10263 30849 40871 6KT
1/4 8KT-743A-24 1 10262 30849 40871 8KTMACHINE SCREW RIVET 5MM MS5M-743A-24 1 10332 30849 40871 5MM
3/16 MB06-734A-20 2,3 10210 36801 48808 MB06
1/4 MB08-734-20 2,3 10213 30833 48808 MB08
3/32 3N-743-20 2 10201 30537 40307 3N
1/8 4N-743-20 2 10202 30537 40307 4N
5/32 5N-743-20 2 10203 30537 40605 5N3/16 6N-743A-24 1 10204 30849 40871 6N1/4 8N-743A-24 1 10211 30849 40871 8N
3/32 3P-743-20 1 10247-1 30537 40307 3P1/8 4P-743-20 1 10202-4 30537 40307 4P
5/32 5P-743-20 1 10203-2 30537 40605 5P3/16 6P-743A-24 1 10167 30849 40871 6P1/4 8P-743A-24 1 10166 30849 40871 8P
3/16 6T-743A-24 1 10209 30849 40871 6T1/4 8T-743A-24 1 10286 30849 40871 8T
TLR RIVET 1/4 8TLR-743A-24 1 10246 30849 40871 8TLR
RIVET DIA. NOSE ASSEMBLY NOSE TIP JAW FOLLOWER DESIGNATION3/16 PH6-734A-20 2,3 10248 36801 48808 PH6
1/4 PH8-734-20 2,3 10205 30833 48808 PH8
1) YOU CAN CHANGE THE 743A NOSE ASSEMBLY (INCLUDED WITH TOOL) TO INSTALL OTHER FASTENERS BY PURCHASING
2) NOSE ASSEMBLIES WITH A 743 AND 734 DESIGNATION, I.E. 5N-743-20, MUST BE ORDERED AS COMPLETE NOSE ASSEMBLY.3) NOSE ASSEMBLIES WITH A 734 DESIGNATION, I.E. PH6-734-20, ARE FOR SERRATED STEM RIVETS ONLY. IF YOU ARE PULlING BOTH SMOOTH AND SERRATED STEM RIVETS YOU MUST ORDER THE NOSE ASSEMBLY WITH A 743 DESIGNATION, I.E. MGL06-743A-24.
PLASTIC SPLIT RIVET
BULB-TITE (STRUCTURAL) RIVET
AVEX (1624 PROTRUDING HEAD)AVEX (1624COUNTERSUNKHEAD)
OPEN ENDCLOSED ENDNAIL RIVET
KLAMPTITE (STRUCTURAL) RIVET
MONOBOLT RIVET
T RIVET
SELECTION CHART FOR PROTRUDING HEAD ONLY
NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTS THE LENGTH THE NOSEEXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES
SERRATED STEM STRUCTURAL RIVET
NOSE TIP SHOWN AND USING APPROPRIATE FOLLOWER SHOWN.
Rev. 11/08
DESCRIPTION
The GBP743C series are pneumatic-hydraulictools designed specifically for the efficientinstallation of a wide range of blind rivets.They can be operated in any position withone hand. They have a rated pull load of 4200pounds with 90 psi air pressure at the airinlet.
The GBP743CSH and GBP743CSR rivetersoffer a unique “split” system providing theoperator with an ergonomic tool withreduced hand held weight, as shown below.
The GBP743C series riveters operate on awide range of air pressure, with 90 to 100 psiproviding the maximum efficiency. At 90 lbsair pressure, the GBP743C series does notexceed 85 db (A) and consumes 3 cfm at 20cycles a minute.
The GBP743C series riveters are furnishedwith nose assembly 8N-743A-24 and sparenose tip 10204 to convert to 6N-743A-24.
OPTIONS
The GBP743C series riveters may be orderedwith a vacuum system. Gage Bilt offers twovarieties (see below)
Order GBP743C series riveters with theproper rivet specification by adding theappropriate suffix (see selection chart)
“V” DESIGNATION = PINTAIL COLLECTOR BOTTLE “VT” DESIGNATION = PINTAIL EVACUATION TUBE
GBP743C SERIES SELECTION CHART
GAGE BILTMADE IN U.S.A.
8.58(217.9mm)5.63
(143mm)
1.50 Ø(38.1mm)
2.25(57.2mm)
4.78(121.6mm)
6.17(156.7mm)
4.88 Ø(123.9mm)
1.50(38.1mm)
2.31 Ø(58.7mm)
2.06 Ø(52.3mm)
1.84(46.7mm)
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp, MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
GBP745DINSTALLATION TOOL
DESCRIPTION Covered under Patent No. 5,485,727
The GBP745D is a pneumatic-hydraulic tool designed specifically for the efficient installation of a wide range ofblind rivets, lockbolts and MAGNA-GRIP® fasteners. It weighs just over 7 lbs. and can be operated in any positionwith one hand. It has a .600" rivet setting stroke and a rated pull load of 6300 pounds with 90 psi air pressure atthe air inlet.
The GBP745D riveter operates on a wide range of air pressure, with 90 to 120 psi providing the maximum efficiency.At 90 lbs. air pressure, the GBP745D does not exceed 82 db (A) and consumes 6.0 cfm at 20 cycles per minute.
The air inlet is provided with 1/4-18 female pipe threads for accepting the user's air hose fitting.
Nose Assemblies that were designed for the Model 353 Installation Tool mount directly on the GBP745D withoutthe use of an adapter.
Nose Assemblies that were designed for the Model 352 Installation Tool will attach to the GBP745D with the useof the 353352 nose assembly adapter.
NOSE ASSEMBLIES ARE NOT FURNISHED WITH THIS RIVETER AND MUST BE ORDERED SEPARATELY.
FASTENER DIA.1/8 4A-745B-23 4A-745B-48 4A-752A-43OS5/32 5A-745B-23 5A-745B-48 5A-752A-43OS3/16 6A-745B-23 6A-745B-48 6A-752A-43OS1/4 SMLS08-755-23 SMLS08-755-48 SMLS08-204C-27OS
13/64 ASP06-745B-23 ASP06-745B-48 ASP06-752A-43OS17/64 ASP08-745B-23 ASP08-745B-48 ASP08-752A-43OS21/64 ASP10-755-23 ASP10-755-48 ASP10-204C-37OS
BLIND OVERSIZE MANDREL 1/4 BOM08-745C-233/16 NAS06-745B-12 NAS06-204B-25OS NAS06-204B-30OS
NAS06-755-23 NAS06-755-48 NAS06-204B-34OS1/4 NAS08-745B-12 NAS08-204B-25OS NAS08-204B-30OS
NAS08-745B-23 NAS08-745B-48 NAS08-205A-31 NAS08-204B-34OS5/16 1 LB10-745C-26 NAS10-756-48 NAS10-205A-313/8 5 LB12-756-26 NAS12-756-48 NAS12-205A-315/32 LGP05-745B-12 LGP05-204B-25OS LGP05-204B-30OS
LGP05-755-23 LGP05-755-48 LGP05-204B-34OS3/16 LGP06-745B-12 LGP06-204B-25OS LGP06-204B-30OS
LGP06-755-23 LGP06-755-48 LGP06-204B-34OS1/4 LGP08-745B-12 LGP08-204B-25OS LGP08-204B-30OS
LGP08-745B-23 LGP08-745B-48 LGP08-204B-34OS LGP08-205A-315/16 LGP10-745B-12
LGP10-756-26 LGP10-756-48 LGP10-205C-315/32 NASS05-745B-12 NAST05-745B-12 NASS05-204B-25OS NAST05-204B-20OS
NASS05-755-23 NAST05-755-23 NASS05-204B-30OS NAST05-204B-30OSNASS05-755-48 NAST05-755-48 NASS05-204B-34OS NAST05-204B-34OS
3/16 NAS06-745B-12 NAS06-204B-25OS NAS06-204B-30OSNAS06-755-23 NAS06-755-48 NAS06-204B-34OS
1/4 NAS08-745B-12 NAS08-204B-25OS NAS08-204B-30OSNAS08-745B-23 NAS08-745B-48 NAS08-204B-34OS NAS08-205A-31
5/16 NAS10-745B-12 NAS10-205A-31NAS10-756-26 NAS10-756-48
3/8 1 NAS12-745B-12 NAS12-205A-31NAS12-756-26 NAS12-756-48
3/16 MG06-745-481/4 MG08-745-48
5/16 2 MG10-756-283/8 3 MG12-756-28
1/8 456MAX-751A-21 7 456MAX-751A-61 7 456MAX-752-42OS 75/32
3/16
1/4 08MAX-745B-23 08MAX-745B-48 08MAX-204C-27OS 08MAX-204C-37OS
5/32 SB05-745B-23 SB05-745B-48 SB05-752A-43OS3/16 SB06-745B-23 SB06-745B-48 SB06-752A-43OS
1/4 SB08-755-23 SB08-755-48 SB08-204C-27OS SB08-204C-37OS
5/16 4 SB10-756-28 SB10-756-48 SB10-205A-355/32 UBB05-745B-23 UBB05-745B-48 UBB05-752A-43OS3/16 UBB06-745B-23 UBB06-745B-48 UBB06-204C-27OS1/4 UBB08-755-23 UBB08-755-48 UBB08-204C-27OS UBB08-204C-37OS
5/16 4 UBB10-756-28 UBB10-756-48 UBB10-205A-351/8 UAB04-745B-23 UAB04-745B-48 UAB04-752A-43OS5/32 UAB568-713-21 6 UAB568-713-61 6 UAB05-752A-43OS3/16 UAB06-752A-43OS1/4 UAB08-204C-27OS UAB08-204C-37OS1/8 SMLS04-745B-23 SMLS04-745B-48 SMLS04-752A-43OS5/32 SMLS05-745B-23 SMLS05-745B-48 SMLS05-752A-43OS3/16 SMLS06-745B-23 SMLS06-745B-48 SMLS06-752A-43OS1/4 SMLS08-755-23 SMLS08-755-48 SMLS08-204C-27OS
STRAIGHT
SINGLE ACTION BLIND RIVETNAS1919S & U NAS1921S & U
BACR15FR/FP, BACR15GF/GK,NAS1919 & NAS1921
"U" TYPE BLIND RIVET WITH DRIVE WASHER
NAS9301-9312
MS90353 & MS90354 MS21140 & MS21141
"U" TYPE BLIND BOLT W/ DRIVE WASHER
MS90353S & U & MS90354S & U MS21140S & U & MS21141S & U
CR7000 SERIES BACB30YY, YU, & YT
THE GAGE BILT GBP745D TOOL IS APPROVED TO INSTALL THE ABOVE FASTENERS
*OFFSET 8
'A' CODENAS1398 & NAS1399 'A'NAS1438 & NAS1439 'A'
PT/MS/9SP MS20600 & MS20601
MULIT-GRIP STRUCTURALBLIND RIVET 3/8 MGL12-353C-28 9
PT08-745-48
EN6122 & UAB130-EUEN6127 & UAB6127-EUEN6128 & UAB100-EUEN6129 & UABP-EU
2 ASP & ASP PFASP FF & ASP F
ASP-LC
COMMERCIAL LOCKBOLTSC6L
ADVELOK
MULTI-GRIP LOCKBOLT
1/4
LIGHTWEIGHT GROOVE PROPORTION LOCKBOLTS
LOCKBOLTNAS SHEAR PULL TYPE
NAS TENSION PULL TYPE& GROOVE PORPORTION
NASS = NAS SHEARNAST = NAS TENSION
EXTENDS FROM THE TOOL I.E. -20 = 2.0 INCHES
NOTE: THE LAST 2 DIGITS OF THE NOSE ASSEMBLY REPRESENTS THE LENGTH THE NOSE
*ALL OFFSET 204 SERIES NOSES REQUIRE 353204 ADAPTER, & ALL OFFSET 205 SERIES NOSES REQUIRE 353205 ADAPTER.1) ALL MATERIALS EXCEPT TITANIUM & STAINLESS.2) 100 PSI REQUIRED FOR ALLOY STEEL.3) ALUMINUM ONLY.
9) 105 P.S.I. REQUIRED FOR ALLOY STEEL.8) ALL OFFSET 752 SERIES NOSES REQUIRE 745751 ADAPTER7) INSTALLS 1/8, 5/32, & 3/16 DIAMETERS.6) INSTALLS 5/32, 3/16 & 1/4 DIAMETERS.
4) 100 PSI REQUIRED FOR ALLOY (MS90353 & 4).5) GENERAL PURPOSE LOCKBOLTS ONLY.
SELECTION CHART FOR GBP745D
Rev. 11/08
GAGE BILT ALSO SUPPLIES PIN & COLLAR SWAGE INSPECTIONGAGES TO CERTIFY CORRECT SWAGE INSTALLATION.
Introducing the GBP745LBK & GBP745LBK-1
GAGE BILT now offers a complete installation kit for 3/16” thru 3/8" C6L & Avdelok® commercial lockbolts. The GBP745LBK comes with a set of straight noses to install –6, -8, -10 & -12 diameters, bleeder bottle, adapter, grip scale and pintail catcher bag. The dash one kit also includes adapters and offset noses, must items for re-work operations. All these items are stored in an easy access carrying case with manuals and data sheets.
Please view the back of this flyer for pictures of your C6L & Avdelok® fasteners and noses to match.
GAGE BILTMADE IN U.S.A.
9/07
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1505 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
STRAIGHT OFFSET
3/16" 1 LB06-722-20 2 NAS06-204B-25OS
1/4" 1 LB08-722-20 3 NAS08-205A-31
*5/16" LB10-745C-26 3 NAS10-205A-31
**3/8" LB12-756-26 3 NAS12-205A-31
1. REQUIRES ADAPTER 7457512. REQUIRES ADAPTER 353204.3. REQUIRES ADAPTER 353205.*ALL MATERIALS EXCEPT TITANIUM & STAINLESS** GENERAL PURPOSE LOCKBOLTS ONLY.
NOSE ASSEMBLIESCOMMERCIAL LOCKBOLTSC6L & AVDELOK® DIA.
8.58(217.9mm)5.63
(143mm)
1.50 Ø(38.1mm)
2.25(57.2mm)
4.78(121.6mm)
6.17(156.7mm)
4.88 Ø(123.9mm)
1.50(38.1mm)
2.31 Ø(58.7mm)
2.06 Ø(52.3mm)
1.84(46.7mm)
GBP745D
LBXX-722-20
1.06(26.9mm) (68.6mm)
1.97(50.1mm)
.48(12.2mm)
NASXX-205A-31
1.950(49.6mm)
.750 Ø(19.1mm)
LB12-756-26
3.125(79.4mm)
1.370(34.8mm)
1.375(34.9mm)
1.130 Ø(28.7mm)
1.310 Ø(33.3mm)
2.500(63.4mm)
1.250(31.8mm)
2.100(53.3mm)
.330 R.(8.4mm)
.810(20.6mm)
1.064(27.0mm)
2.625(66.7mm)
NASXX-204B-25OS
Introducing the GBP745TCK… Trailer and Cab Kit
Choose GAGE BILTS’ blind rivet and lockbolt installation kit designed especially for Truck and Trailer OEM’s. The GBP745TCK can be configured to meet your needs, whether you’re fixing Wabash, Great Dane, Peterbilt, Kenworth or any other brand trailer or truck. The kit includes nose assemblies to pull your fasteners, and at the heart of the system is our heavy-duty GBP745D installation tool. All of this is conveniently stored in a metal tool case.
The GBP745TCK kit comes with a nose and 2 tips to install 3/16” and 1/4” structural blind rivets in any material, a bleeder bottle, a catcher bag for pintails, a 3/16” & 1/4” Magna-Grip® nose for the hood and cab and a 3/8” C6L Huckbolt nose. An adapter is included for the noses through 1/4”.
GAGE BILTMADE IN U.S.A.
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
3/07 Rev. 8/07
3/16"ALUMINUM, STEEL OR
STAINLESS STEEL MAGNA-LOK® BLIND RIVET
MGLC68-752A-21(USE 10248-4 NOSE TIP)
1/4"ALUMINUM, STEEL OR
STAINLESS STEEL MAGNA-LOK® BLIND RIVET
MGLC68-752A-21(USE 10211-1 NOSE TIP)
3/16" STAINLESS STEEL C6L
3/16" STEEL C6L
3/16" ALUMINUM C6L
3/16" STEEL MAGNA-GRIP®
3/16" ALUMINUM MAGNA-GRIP®
1/4" STEEL MAGNA-GRIP®
1/4" ALUMINUM MAGNA-GRIP®
3/8" STEEL C6L
3/8" ALUMINUM C6L
MG06-722-60
MG08-722-20
LB12-756-26
GBP745TCKBLIND RIVETS
LOCKBOLTS
LB06-722-20
LB06-722-20 MG06-722-60
MG08-722-20
.750 Ø 2.230
MGL68-752A-21
1.06(26.9mm)
2.70(68.6mm)1.97
(50.1mm).48
(12.2mm)
LB12-756-26
8/07
2.000.750 Ø
1.950.750 Ø 5.954.750 Ø
GAGE BILTMADE IN U.S.A.
GAGE BILT PRODUCTS CORP. 44766 Centre Court (586) 226-1500 Clinton Twp. MI 48038 (586) 226-1505 Fax e-mail:[email protected] / www.gagebilt.com
1.92(48.7mm)
5.07(128.7mm)
1.40(35.5mm)
3.88 Ø(98.5mm)
4.16(105.6mm)
7.09(180.0mm)4.58
(116.3mm)1.25 Ø
(31.7mm)
1.56 Ø(39.6mm)
1.78(45.2mm)
7.15(181.6mm)
3.47(88.1mm)
GBP751D SERIES INSTALLATION TOOLS
GAGE BILT TOOLS ARE AVAILABLE WORLDWIDE E-MAIL US FOR A DISTRIBUTOR NEAR YOU
GBP751D
GBP751DSRGBP751DSH