Installation InstructionsQUIKTUNE® DROP-AWAY 2000RG

For your convenience, an Installation DVD is also included.

FIG. 1

Mounting the Arrow Holder Pad1. Apply at room temperature.

2. Use the enclosed alcohol wipe to clean shelf. Allow shelf to dry.

3. Mathews centershot on Legacy, Icon, LX, Ovation and Outback bows is 13/16 inch. Remove the adhesive backing and apply the arrow holder on the shelf with the center of the "v" centered at 13/16 inch and one edge of the arrow holder even with the back edge of the bow shelf (Fig. 1).

4. Firmly press the arrow holder down. The pressure sensitive adhesivedevelops full strength in 24 hours.

5. Trim excess off the front of the holder as needed (Fig. 2).

Mounting the restRight & Left Handed Bows (Right Hand Shown)

1. If the roller guard is the short model and looks like Fig. 3, mount the rest using the 5/16 x 24 cap screw in the number 1 position (Fig. 3A).

2. If the roller guard is a long model and looks like Fig. 4 or Fig. 4A, mount the rest using the 5/16 x 24 cap screw in the number 2 position (Fig. 4B).

FIG. 2TRIMMED FRONT OF

ARROW HOLDER

51-230 (REV 1)

FIG. 3 FIG. 3A

TWO HOLES

Setting Centershot 1. Loosen the lift arm lock screw (Fig. 5) and allow the lift arm to swing

down toward the bow handle. The lift arm position will be set after centershot and prong height.

2. The QuikTune Drop-Away 2000RG has been preset at the factory to Mathews recommended centershot - 13/16” (Fig. 6).

3. If the rest has been moved horizontally from the factory setting, loosen the horizontal/vertical lock screw on the bottom of the bracket (Fig. 5).

4. Use a ruler to move the horizontal centershot back to 13/16”.

FIG. 4 FIG. 4A FIG. 4B

FIG. 5

LIFT ARMLIFT ARM

LOCK SCREW

FIG. 6

13/16”

THREE HOLES FOUR HOLES

HORIZONTAL/VERTICALLOCK SCREW

FIG. 7

FIG. 8

FIG. 9 FIG. 10

LAUNCHER POSITIONLOCK SCREW

PLUNGER HOLECOVERED BY ARROW

90°

BOTTOM OF PLUNGERHOLE SHOWS

HORIZONTAL/VERTICALLOCK SCREW

13/16”

Page 2

Arm hangs down

Page 3Page 1

90°

Setting the Nock Point and Arrow Height1. Loosen the launcher position lock screw (Fig. 7). 2. Turn the knob toward the up arrow until the rest prongs move to the

upright position. (Fig. 8).3. Tighten the launcher position lock screw.4. Loosen the horizontal/vertical lock screw on the

bottom of the bracket (Fig.7).5. Loosely (not completely clamped) set a nock point on the string.6. Nock an arrow on the string.7. Simultaneously rotate the brass barrel shaft assembly and adjust the

nock point on the string so that the arrow is square when resting on the raised prongs. For carbon or small diameter arrows the arrow shaft should equally cover the plunger hole (Fig.9). With larger diameter arrows e.g. 2315, the very bottom of the plunger hole should show beneath the arrow shaft (Fig. 10).

8. Tighten the horizontal/vertical lock screw on the bottom of the bracket(Fig. 7).

9. Completely clamp the nock point. THE REST IS STILL IN THE RAISED POSITION and the lift arm is still loose and hanging down.

EXTREMELY IMPORTANT: DO NOT USE METAL “D” NOCKS WITH THE QUIKTUNEDROP-AWAY 2000RG ON THE MATHEWS LX BOW.

Due to the LX Model’s 6-5/8” brace height, use of Ultra-Nok or metal “D” typenocks will impact the QuikTune Drop-Away 2000RG’s Lift Arm and cause it to break.

INSTRUCTION INSERT 6/12/06 2:20 PM Page 1

Mounting the Lift Arm Ball1. Identify the bow cable on the Mathews Legacy, Icon or LX. The bow

cable has the split harness anchored to the top limb of these bows (FIG. 11).

2. Using the 1/16th hex head wrench, remove the 1-72 cap screws from the lift arm ball (Fig. 12) .

3. Place each half of the ball on opposite sides of the bow cable about 1/4 to 3/8 inch from the roller guard wheel.

4. Insert and tighten (do not over tighten) the 1-72 cap screws (Fig.13). The lift arm ball should be clamped tightly and should not be able to move up or down the cable freely.

FIG. 11

FIG. 12

FIG. 13

SPLIT HARNESS

1/4” to 3/8” Instructions also available on line at www.newarchery.com

New Archery Products Corp.7500 Industrial Drive � Forest Park, Illinois 60130

708.488.2500 � 800.323.1279 � Fax: 708.488.2515www.newarchery.com

TroubleshootingFor help with troubleshooting specific problems, please visit our website at www.newarchery.com

PRONGS SHOULD REST ON BOW SHELFLAUNCHER POSITION

LOCK SCREW

8. Loosen the launcher position lock screw (Fig. 17).

9. Turn the launcher position knob toward the down arrow until the rest prongs move to the shoot position (prongs resting on the shelf).

10. Tighten the launcher position lock screw. The screw should bein the 7 o’clock position.

11. The prong assembly should now be resting on the bow shelf if the roller guard is the short model (Fig. 18) or the tips of the prongs are touching the shelf if the roller guard is a long model (Fig. 18A).

The QuikTune Drop-Away 2000RG should now be set toshoot.

FIG. 17

FIG. 18 FIG. 18AProper setup - bow with short roller guard (2 holes)*

Proper setup - bow with long roller guard (3 or 4 holes)*

FIG. 14Adjusting the Lift Arm Travel1. Move the lift arm completely against the black

spacer washer next to the brass barrel (Fig. 14).

2. Slightly tighten the lift arm lock screw. EXTREMELY IMPORTANT!!! The lift arm should be clamped tight enough to hold position, but still move if pushed up or down.

3. Position each finger of the lift arm on either side of the cable.

4. Swing the lift arm up to touch the lift arm ball (Fig. 15).

5. Draw the bow to full draw. This action sets the lift arm travel(Fig. 16).

6. Let bow down from full draw.

7. Tighten the lift arm lock screw completely (Fig. 15). The lift arm should no longer pivot easily on the shaft.

BLACK SPACER WASHER

FIG. 15

CABLE BETWEEN LIFTARM FINGERS

FIG. 16Page 4 Page 5 Page 6

LIFT ARM LOCK SCREW

* The space between lift arm and ball activator cam will varydepending on bow model and draw length

INSTRUCTION INSERT 6/12/06 2:20 PM Page 2