52 hhw katalog 2015 eng - venten oÜ · 2019. 7. 2. · 52_hhw_katalog_2015_eng 03.09.15 08:47...
TRANSCRIPT
-
Hand
Tools
52.1eng/OP www.hhw.deFax order hotline: +49 6204 739-1217a = Sales are restricted to the packaging units mentioned in the catalogue. Purchase orders must be in units.# = partly extent in stock.
So that you have everything under control ... Screwdrivers from ßInfo
sBlade made of high-alloyed specialsteel, nicromatt, drive Lasertip®
Black-Point tip.Ergonomically optimisedKraftform handle with hardand soft zones for the greatesttorque transmission, handlewith roll-off protection.
sNote:Kraftform screwdriver with LasertipbladeBetter results thanks toHigher safetyHigher power transmissionHigher speed
+Blade made of high-quality chrome vanadium-molybdenum steel,through-hardened, glossy nickel-plated. ChromTop® tip.Robust square handlemade of impact-proof plastics, chemicals and oil-resistant.
+Blade made of high-qualitychrome-vanadium steel, through-hardened, glossy nickel-plated. ChromTop® tip.Wooden handle made ofsealed beech wood. Impacthead with leather cap,therefore no damage toend of handle. Starting at5.5 mm with full-lengthblade, hex bolster foradditional torque andblade with slipprotection.
0Blade made of chrome-vana-dium-molybdenum steel,through-hardened, blacke-ned tip, hex bolster foradditional torque. Multi-component handlewith extra large soft zoneand hanging hole.
xBlade made of vanadium-extra steel, matt-chromefinish, through-hardened,burnished tip. Ergonomic3-component handle,impact-proof. Permanentcolour coding on both handleends.
sThe chisel-screwdriverWith impact cap and full-length blade. Highly ductile. Blade made of high-alloyed special steel, nicromatt, starting at 0.8 x 4.5 with hex bolster for additional torque. Drive Black-Point tip. Ergonomically optimisedKraftform handle with hard and soft zones for the greatest torque transfer, handle with roll-off protection.
+Blade made of high-quality chrome vanadium-molybdenum steel, through-hardened, matt-chrome finish. ChromTop® tip.Ergonomic SoftFinish®- handle for highest torque transfer, with roll-off protection.
x
Routine-tested, DIN EN 60900 (IEC 900). Blade made of vanadium-extra steel, matt-chrome finish, through-hardened, burnished tip. Ergonomic3-component handle, impact-proof. Permanentcolour coding on both handle ends.
s
Routine-tested in compliance with: IEC 60900:2004.
+
Blade made of high-quality chrome-vanadium-molybdenum steel, through-hardened, burnished. Ergonomic SoftFinish® handle for the highest torque transfer, with roll-off protection. Manufactured to IEC 60900:2004.s
Blade made of high-alloyed special steel. Black-Point tip. Ergonomically optimised Kraftform handle with roll-off protection. For work on electrostatically sensitive electronic components. Complies with EN 100-015 Part 1.Note:Due to the electrical conductivity of the ESD/ESDhandle, these tools may not come into contact with power sources, because damage due to an electric shock cannot be excluded.
52_HHW_Katalog_2015_eng 03.09.15 08:47 Seite 52.1
-
Hand Tools
52.2 eng/OPwww.hhw.deFax order hotline: +49 6204 739-1217 a = Sales are restricted to the packaging units mentioned in the catalogue. Purchase orders must be in units. # = partly extent in stock.
Magnetic storage trayTypeRound, made of stainless steel. Thanks to magneticeffect on both sides, the tray can be attached to alliron surfaces such as a tool and gear wagon, toolwalls or lifting platform. To protect the subsurface,the magnetic surface is coated with rubber.
UseUniversally usable magnetic tray with strongmagnets that firmly holds small parts such asscrews or wheel studs.
52002
Permanent magnetising and demagnetising device
+TypeHousing made of rigid plastics, cadmium-free.
UseFor magnetising and/or demagnetising of screwdriver blades, tweezers and similar tools made ofsteel.
52000
W x H x D 52000 … mm 52 x 50 x 29 101
Ø 52002 … mm 150 101
Jeweller’s Screwdriver SetsTypeDIN8320 BS1. Handles made of impact-proofplastic, handle end rotatable.
QualityBlade made of chrome-vanadium steel, hardened and burnished.
52004 101
Set contents Cutting edge width x overall length Type 52004 … mm 5-piece 1.0 x 104 / 1.4 x 104 / 1.8 x 104 / 2.3 x 104 / 3.0 x 104 in plastic case 101 7-piece 0.6 x 104 / 0.8 x 104 / 1.0 x 104 / 1.2 x 104 / 1.4 x 104 / 1.8 x 104 / 2.3 x 104 in wooden box 102
Jeweller’s ScrewdriversTypeSimilar to DIN 8320. Blade hardened, with fluted,nickel-plated handle made of steel, revolving handleend.
QualityBlade made of chrome-vanadium steel. 52005
Set contents Cutting edge width x overall length Type 52005 … mm 6-piece 1.0 x 83 / 1.5 x 87 / 1.8 x 101 / 2.3 x 104 / 3.0 x 117 / 3.5 x 117 in wooden box 101
Cutting edge width x thickness Handle Ø Overall length 52009 … mm mm mm 1.0 x 0.20 4 83 101 1.5 x 0.23 4 87 102 1.8 x 0.30 6 101 103
Cutting edge width x thickness Handle Ø Overall length 52009 … mm mm mm 2.3 x 0.30 6 104 104 3.0 x 0.50 8 117 105 3.5 x 0.60 8 117 106
52002
52000
52004
52005 - 52009
Universal ScrewdriversType4 blades, hardened, exchangeable, in handle, shankmade of brass, nickel-plated, handle fluted.
QualityBlade made of chrome-vanadium steel. 52015
Cutting edge width x thickness Handle Ø Overall length 52015 … mm mm mm 1.5 x 0.23 / 2.0 x 0.4 / 2.5 x 0.4 / 3.0 x 0.5 8.5 115 101
52015
Storage trays │ Magnetising/demagnetising device │ Screwdrivers
52_HHW_Katalog_2015_eng 03.09.15 08:47 Seite 52.2
-
Hand
Tools
52.3eng/OP www.hhw.deFax order hotline: +49 6204 739-1217a = Sales are restricted to the packaging units mentioned in the catalogue. Purchase orders must be in units.# = partly extent in stock.
Workshop screwdriver
0Type Round blade, through-hardened, glossy nickel-plated. Multi-component handle with extra largesoft zone and hanging hole.
Quality Blade made of chrome-vanadium steel.
Note: Cutting edge width 3.0 and 4.0 mm with identicalcutting edge and shank diameter.
52065
Set contents Cutting edge width x blade length Type 52065 … mm 6-piece 3.0 x 80 / 4.0 x 100 / 5.5 x 125 / 6.5 x 150 / 8.0 x 175 / 10.0 x 200 in cardboard box 201
Workshop screwdriver
+TypeRound blade, glossy nickel-plated, through-harde-ned. With impact-proof, transparent plastic squarehandle, chemical and oil-resistant made of celluloseacetate, red.
QualityBlade made of chrome-vanadium-molybdenumsteel.
Note:Starting at 5.5 mm cutting edge width, corrugated tipagainst slipping.
52110
Workshop screwdriver
+TypeDrive: DIN 5265, ISO 2380. Round blade, through-hardened, matt-chrome finish. ChromTop® tip.SoftFinish® handle with roll-off protection.
QualityBlade made of high-quality chrome-vanadium-molybdenum steel.
52120 208-221
52120 230-233
Cutting edge width x thickness Blade length Overall length 52066 … mm mm mm 4.5 x 0.8 100 207 201 5.5 x 1.0 125 232 202 6.5 x 1.2 150 269 203
Cutting edge width x thickness Blade length Overall length 52066 … mm mm mm 8.0 x 1.2 175 294 204 10.0 x 1.6 200 319 205
Cutting edge width x thickness Blade length Overall length 52110 … mm mm mm 7.0 x 1.05 140 255 105 9.0 x 1.2 160 275 106 10.0 x 1.4 180 305 # 107
Cutting edge width x thickness Blade length Overall length 52110 … mm mm mm 2.5 x 0.4 75 150 101 3.5 x 0.5 90 175 102 4.5 x 0.7 100 195 103 5.5 x 0.95 120 225 104
Cutting edge width x thickness Blade length Overall length 52120 … mm mm mm 4.0 x 0.8 100 211 208 5.5 x 1.0 125 236 213 6.5 x 1.2 150 268 218 L 8.0 x 1.2 175 299 221
Cutting edge width x thickness Blade length Overall length 52120 … mm mm mm 4.0 x 0.8 25 81 230 5.5 x 1.0 25 81 231 6.5 x 1.2 25 81 232 8.0 x 1.2 25 81 233
52110
52065 - 52066
52120
Workshop screwdriver
sTypeDrive: DIN 5264 A, ISO 2380. Round blade,nicromatt, with Lasertip to prevent slipping out ofthe screw and Kraftform handle with hard and softzones as well as roll-off protection.
QualityBlade made of 73 Mo V 5 2. 52123
Cutting edge width x thickness Blade length Overall length 52123 … mm mm mm 7.0 x 1.2 150 255 104 8.0 x 1.2 175 287 105 10.0 x 1.6 200 312 106
Cutting edge width x thickness Blade length Overall length 52123 … mm mm mm 5.0 x 0.8 100 198 101 6.0 x 1.0 125 230 102 6.5 x 1.2 150 255 103
52123
52_HHW_Katalog_2015_eng 03.09.15 08:47 Seite 52.3
-
Hand Tools
52.4 eng/OPwww.hhw.deFax order hotline: +49 6204 739-1217 a = Sales are restricted to the packaging units mentioned in the catalogue. Purchase orders must be in units. # = partly extent in stock.
52125 201-206
52125 208-209
Workshop screwdriver
xTypeDrive: DIN 5264 A, ISO 2380-1 A.Round blade, matt-chrome finish, through-harde-ned, burnished tip. Ergonomic 3-component handle,impact-proof. Permanent colour coding on bothhandle ends (for slotted screws = yellow).
QualityBlade made of vanadium-extra steel.
52125 207
Stubby Screwdrivers (Carburettor Screwdrivers)
xTypeDrive: DIN 5264 A, ISO 2380-1 A.Round blade, matt-chrome finish, through-harde-ned, burnished tip. Ergonomic 3-component handle,impact-proof. Permanent colour coding on bothhandle ends (for slotted screws = yellow).
QualityBlade made of vanadium-extra steel. 52376
Workshop screwdriver
+TypeRound blade, glossy nickel-plated, through-harde-ned, with handle made of hardwood, beechwood,lacquered. Impact head with leather cap, thereforeno damage to end of handle.
QualityBlade made of chrome-vanadium steel.
Note:Starting at 5.5 mm cutting edge width full-lengthblade, hex bolster for additional torque and corruga-ted tip against slipping.
52138
Set contents Cutting edge width x blade length Type 52138 … mm 5-piece 3.5 x 75 / 4.5 x 90 / 5.5 x 100 / 7.0 x 125 / 9.0 x 150 in cardboard box 101
Cutting edge width x thickness Blade length Overall length 52125 … mm mm mm 4.0 x 0.8 100 222 206 5.5 x 1.0 150 272 207 6.5 x 1.2 150 272 208 8.0 x 1.6 175 297 209
Cutting edge width x thickness Blade length Overall length 52125 … mm mm mm 2.5 x 0.4 75 197 201 3.0 x 0.5 75 197 202 L 3.0 x 0.5 125 247 203 3.5 x 0.6 75 197 204 L 3.5 x 0.6 125 247 205
Cutting edge width x thickness Blade length Overall length 52376 … mm mm mm 6.5 x 1.2 25 83 205 8.0 x 1.2 25 83 207
Cutting edge width x thickness Blade length Overall length 52376 … mm mm mm 3.5 x 0.6 25 83 201 4.0 x 0.8 25 83 202 5.5 x 1.0 25 83 203
Cutting edge width x thickness Blade length Overall length 52140 … mm mm mm 3.5 x 0.6 75 175 101 4.5 x 0.8 90 190 102 5.5 x 0.95 100 205 103 7.0 x 0.95 125 230 104
Cutting edge width x thickness Blade length Overall length 52140 … mm mm mm 9.0 x 1.1 150 270 105 10.0 x 1.2 175 295 106 12.0 x 1.4 200 325 107 14.0 x 1.75 250 380 108
52125
52376
52138 - 52140
Workshop screwdrivers │ Carburettor screwdrivers
... new ideas arise.When you think laterally ...
www.atorn.de Performance requires quality
52_HHW_Katalog_2015_eng 03.09.15 08:47 Seite 52.4
-
Hand
Tools
52.5eng/OP www.hhw.deFax order hotline: +49 6204 739-1217a = Sales are restricted to the packaging units mentioned in the catalogue. Purchase orders must be in units.# = partly extent in stock.
Workshop screwdriver
+Type Drive: DIN 5265, ISO 2380. Hexagonal blade through-hardened, matt-chromefinish. ChromTop® tip. SoftFinish® handle with roll-off protection. Starting at 5.5 x 1.0 mm with hexbolster for additional torque.
Quality Blade made of high-quality chrome-vanadium-molybdenum steel.
52151
Workshop screwdriver
+Type Drive: DIN 5265, ISO 2380. Hexagonal blade through-hardened, matt-chromefinish. ChromTop® tip. SoftFinish® handle with roll-off protection and solid steel cap. Starting at 5.5 x1.0 mm with hex bolster for additional torque.
Quality Blade made of high-quality chrome-vanadium-molybdenum steel.
52153
Workshop screwdriver
0Type Drive: DIN 5625, ISO 2380. Hexagonal blade with hex bolster for additionaltorque, through-hardened, matt-chrome finish,blackened tip. Multi-component handle with extra large softzone and hanging hole.
Quality Blade made of chrome-vanadium-molybdenumsteel.
52152
Workshop screwdriver/The chisel-screwdriver
sTypeDrive: DIN 5264 A, ISO 2380.Full-length hexagonal blade with impact cap andhex bolster for additional torque (starting at 4.5 x 0.8mm). Black Point tip, exceptionally tough tempered.Kraftform handle with hard and soft zones as wellas roll-off protection.
UseFor screwing, chiselling and stemming.QualityBlade made of 73 Mo V 5 2.
Note:For blade length 200 and 250 mm handle made ofsingle-component material.
52154
Cutting edge width x blade length Overall length 52152 … mm mm 8.0 x 150 262 305 10.0 x 175 287 306 12.0 x 200 312 307
Cutting edge width x blade length Overall length 52152 … mm mm 3.5 x 75 165 301 4.5 x 90 190 302 5.5 x 100 212 303 6.5 x 125 237 304
Cutting edge width x thickness Blade length Overall length 52151 … mm mm mm 8.0 x 1.2 150 268 106 9.0 x 1.4 150 268 107 10.0 x 1.6 175 293 108 12.0 x 2.0 200 318 109 14.0 x 2.5 250 368 110
Cutting edge width x thickness Blade length Overall length 52151 … mm mm mm 3.5 x 0.6 75 186 101 4.5 x 0.8 90 201 102 5.5 x 1.0 100 213 103 6.5 x 1.2 125 238 104 7.0 x 1.1 125 238 105
Cutting edge width x thickness Blade length Overall length 52153 … mm mm mm 8.0 x 1.2 150 271 205 10.0 x 1.6 175 296 206 12.0 x 2.0 200 321 207 14.0 x 2.5 250 371 208
Cutting edge width x thickness Blade length Overall length 52153 … mm mm mm 3.5 x 0.6 75 186 201 4.5 x 0.8 90 201 202 5.5 x 1.0 100 213 203 6.5 x 1.2 125 238 204
Cutting edge width x thickness Blade length Overall length 52154 … mm mm mm 9.0 x 1.6 150 262 105 10.0 x 1.6 175 287 106 12.0 x 2.0 200 317 107 14.0 x 2.5 250 319 108
Cutting edge width x thickness Blade length Overall length 52154 … mm mm mm 3.5 x 0.6 80 161 101 4.5 x 0.8 90 188 102 5.5 x 1.0 100 205 103 7.0 x 1.2 125 230 104
Set contents Cutting edge width x blade length Type 52152 … mm 6-piece 3.5 x 75 / 4.5 x 90 / 5.5 x 100 / 6.5 x 125 / 8.0 x 150 / 10.0 x 175 in cardboard box
52152
52151
52153
52154
52_HHW_Katalog_2015_eng 03.09.15 08:47 Seite 52.5
-
Hand Tools
52.6 eng/OPwww.hhw.deFax order hotline: +49 6204 739-1217 a = Sales are restricted to the packaging units mentioned in the catalogue. Purchase orders must be in units. # = partly extent in stock.
Workshop screwdriver
sType Drive: DIN 5264 A, ISO 2380.With Lasertip to prevent slipping out of the screw.Hexagonal blade, nicromatt, hex bolster foradditional torque (starting at 4.5 x 0.8 mm) andKraftform handle with hard and soft zones as wellas roll-off protection.
QualityBlade made of 73 Mo V 5 2. 52156
Workshop screwdriver
xTypeDrive: DIN 5264-A ISO 2380-1-A.Hexagonal blade, matt-chrome finish, through-har-dened, burnished tip. Hex bolster for additionaltorque. Ergonomic 3-component handle, impact-pro-of. Permanent colour coding on both handle ends(for slotted screws = yellow).
QualityBlade made of vanadium-extra steel. 52157 201-203
52157 204-205
Electrician’s screwdriver
0Type Round blade, through-hardened, glossy nickel-plated. Multi-component handle with extra largesoft zone and hanging hole. With identical cuttingedge width and shank diameter.
Quality Blade made of chrome-vanadium steel. 52162
Set contents Cutting edge width x blade length Type 52165 … mm 5-piece 2.5 x 75 / 3.0 x 80 / 4.0 x 100 / 5.5 x 125 / 5.5 x 200 in cardboard box 101
Cutting edge width x thickness Blade length Overall length 52156 … mm mm mm 6.5 x 1.2 125 230 105 7.0 x 1.2 125 230 106 9.0 x 1.6 150 262 107 10.0 x 1.6 175 287 108
Cutting edge width x thickness Blade length Overall length 52156 … mm mm mm 3.5 x 0.6 75 156 101 4.0 x 0.8 90 171 102 4.5 x 0.8 90 188 103 5.5 x 1.0 100 198 104
Cutting edge width x thickness Blade length Overall length 52157 … mm mm mm 10.0 x 1.6 175 336 204 12.0 x 2.0 200 361 205
Cutting edge width x thickness Blade length Overall length 52157 … mm mm mm 5.5 x 1.0 125 247 # 201 6.5 x 1.2 150 272 202 8.0 x 1.6 175 297 203
Cutting edge width x thickness Blade length Overall length 52162 … mm mm mm 4.0 x 0.8 100 207 204 5.0 x 0.8 100 207 205 6.0 x 1.1 150 269 206
Cutting edge width x thickness Blade length Overall length 52162 … mm mm mm 2.5 x 0.4 75 161 201 3.0 x 0.5 80 166 202 3.5 x 0.6 100 197 203
Cutting edge width x thickness Blade length Overall length 52168 … mm mm mm 4.0 x 0.8 100 198 107 L 4.0 x 0.8 150 248 108 XXL 4.0 x 0.8 300 398 110 5.5 x 1.0 125 223 111 L 5.5 x 1.0 150 248 112 XXL5.5 x 1.0 300 398 114
Cutting edge width x thickness Blade length Overall length 52168 … mm mm mm 2.0 x 0.4 60 141 100 2.5 x 0.4 60 141 101 L 2.5 x 0.4 75 156 102 3.0 x 0.5 80 161 103 3.5 x 0.6 100 181 104 L 3.5 x 0.6 125 206 105 XL 3.5 x 0.6 200 281 106
52156
52157
52162
Workshop │ Electricians │ ESD/EGB- │ VDE electrician’s screwdriver
sTypeDrive: DIN 5264 A, ISO 2380.Round blade, nicromatt, with Lasertip (3.5 - 5.5mm cutting edge width) to prevent slipping out ofthe screw and Kraftform handle with hard and softzones as well as roll-off protection. With identicalcutting edge width and shank diameter.
QualityBlade made of 73 Mo V 5 2.
52168Note: Blade length 300 mm without Lasertip.
52168
Electrician’s screwdriver52165 - 52168
52_HHW_Katalog_2015_eng 03.09.15 08:48 Seite 52.6
-
Hand
Tools
52.7eng/OP www.hhw.deFax order hotline: +49 6204 739-1217a = Sales are restricted to the packaging units mentioned in the catalogue. Purchase orders must be in units.# = partly extent in stock.
ESD/EGB screwdriver
sTypeDrive: DIN 5264, ISO 2380.Round blade, Black-Point tip, ergonomicallyoptimised Kraftform handle with hard and softzones as well as roll-off protection.
UseFor working on electrostatically endangeredelectronic components. Complies with EN 100-015Part 1.QualityBlade made of high-alloyed special steel.
52169
VDE electrician’s screwdriver
0Type Drive: DIN 5264, ISO 2380. Routine-tested incompliance with DIN EN 60900 (IEC 900), DIN 7437.Multi-component handle with extra large softzone and hanging hole.
QualityBlade burnished, insulated. 52180
Set contents Cutting edge width x blade length Type 52180 … mm 5-piece 2.5 x 75 / 4.0 x 100 / 5.5 x 125 / 6.5 x 150 / 8.0 x 175 in cardboard box 201
Cutting edge width x thickness Blade length Overall length 52320 … mm mm mm 3.5 x 0.6 100 204 101 4.0 x 0.8 100 211 102 5.5 x 1.0 125 243 103 6.5 x 1.2 150 268 104
VDE electrician’s screwdriver slimFix
+TypeDrive: DIN 5264, ISO 2380.Manufactured to IEC 60900:2004.SoftFinish® handle with roll-off protection. Theprotective insulation is completely integrated in thefront part of the blade. 38 mm constantly thinnerdiameter: Low-lying fastening and spring elementscan be effortlessly reached.
QualityBlade made of chrome-vanadium-molybdenumsteel, through-hardened, burnished.
52320
VDE electrician’s screwdriver
+TypeDrive: DIN 5264, ISO 2380.Manufactured to IEC 60900:2004. Protectiveinsulation sprayed directly on the blade. SoftFinish®
handle with roll-off protection.
QualityBlade made of chrome-vanadium-molybdenumsteel, through-hardened, burnished.
52324
Set contents Cutting edge width x blade length Type 52323 … mm 5-piece 2.5 x 75 / 4.0 x 100 / 5.5 x 125 / 6.5 x 150 / 8.0 x 175 in cardboard box 101
Cutting edge width x thickness Blade length Overall length 52169 … mm mm mm 7.0 x 1.2 150 262 207 8.0 x 1.2 175 287 208
Cutting edge width x thickness Blade length Overall length 52169 … mm mm mm 5.5 x 1.0 200 298 # 204 6.0 x 1.0 125 223 # 205 6.5 x 1.2 150 248 206
Cutting edge width x thickness Blade length Overall length 52181 … mm mm mm 5.5 x 1.0 125 244 205 6.5 x 1.2 150 269 206 8.0 x 1.2 175 294 207 10.0 x 1.6 200 319 208
Cutting edge width x thickness Blade length Overall length 52181 … mm mm mm 2.5 x 0.4 75 161 201 3.0 x 0.5 100 186 202 3.5 x 0.6 100 197 203 4.0 x 0.8 100 207 204
Cutting edge width x thickness Blade length Overall length 52324 … mm mm mm 5.5 x 1.0 125 243 108 L 5.5 x 1.0 175 293 109 6.5 x 1.2 150 268 111 8.0 x 1.2 175 299 112
Cutting edge width x thickness Blade length Overall length 52324 … mm mm mm 2.5 x 0.4 75 179 102 3.5 x 0.6 100 204 104 4.0 x 0.8 100 211 105 4.5 x 1.0 125 236 106
52169
52180 - 52181
52320
52323 - 52324
52_HHW_Katalog_2015_eng 03.09.15 08:48 Seite 52.7
-
Hand Tools
52.8 eng/OPwww.hhw.deFax order hotline: +49 6204 739-1217 a = Sales are restricted to the packaging units mentioned in the catalogue. Purchase orders must be in units. # = partly extent in stock.
VDE electrician’s screwdriver
+TypeDrive: DIN 5264, ISO 2380.Manufactured to IEC 60900:2004. Impact-proof, chemical- and oil-resistant square handle.
QualityBlade made of chrome-vanadium steel, through-hardened, burnished.
52325
VDE electrician’s screwdriver
sTypeDrive: DIN 5264 A, ISO 2380.Blade burnished, insulated. Conical tip, with Lasertip (3.5 - 10 mm cutting edge width) to prevent slipping out of the screw. Routine-tested in compliance with: IEC 60900:2004. Soft zone Kraftform handle with hard andsoft zones as well as roll-off protection.
QualityBlade made of 73 Mo V 5 2. 52326
VDE electrician’s screwdriver
xTypeDrive: DIN 5264 A, ISO 2380-1. Routine-tested,DIN EN 60900 (IEC 900), DIN 7437. Blade matt-chrome finish, through-hardened, burnished tip.Ergonomic 3-component handle, impact-proof.Permanent colour coding on both handle ends (for slotted screws = yellow).
QualityBlade made of vanadium-extra steel.
52328 205-207
52328 201-204
Screwdriver (terminal blade screwdriver)
xTypeBlade coated to tip, hardened. Tapered, slim handlemade of plastics.
UseFor set screws (grub screws) M 2.3 - M 5.QualityBlade made of vanadium-extra steel.
52371
Cutting edge width x thickness Blade length Overall length 52325 … mm mm mm 4.5 x 1.0 125 220 110 5.0 x 1.0 100 195 111 L 5.0 x 1.0 150 245 112 5.5 x 1.0 125 230 113 6.0 x 1.2 100 205 114 6.5 x 1.2 150 255 115 8.0 x 1.2 175 290 116 10.0 x 1.6 200 325 117
Cutting edge width x thickness Blade length Overall length 52325 … mm mm mm 2.3 x 0.5 60 135 101 2.5 x 0.4 75 150 102 2.8 x 0.6 75 150 103 3.0 x 0.5 100 175 104 L 3.0 x 0.5 150 225 105 3.5 x 0.6 100 185 106 3.5 x 0.8 100 185 107 4.0 x 0.8 100 195 108 L 4.0 x 0.8 150 245 109
Cutting edge width x thickness Blade length Overall length 52326 … mm mm mm 5.5 x 1.0 125 223 105 6.5 x 1.2 150 255 106 8.0 x 1.2 175 287 107 10.0 x 1.6 200 312 109
Cutting edge width x thickness Blade length Overall length 52326 … mm mm mm 2.5 x 0.4 80 161 101 3.0 x 0.5 100 181 102 3.5 x 0.6 100 181 103 4.0 x 0.8 100 198 104
Cutting edge width x thickness Blade length Overall length 52328 … mm mm mm 5.5 x 1.0 125 247 205 6.5 x 1.2 150 272 206 8.0 x 1.2 175 297 207
Cutting edge width x thickness Blade length Overall length 52328 … mm mm mm 2.5 x 0.4 75 177 201 3.0 x 0.5 100 202 202 3.5 x 0.6 100 222 203 4.0 x 0.8 100 222 204
Cutting edge width x thickness Blade length Overall length 52371 … mm mm mm 3.0 x 0.5 80 165 203
Cutting edge width x thickness Blade length Overall length 52371 … mm mm mm 2.0 x 0.4 63 143 201 2.5 x 0.4 75 155 202
52325
52326
52328
52371
VDE electrician’s screwdrivers │ Terminal blade screwdriver │ Phillips screwdrivers PH
52_HHW_Katalog_2015_eng 03.09.15 08:48 Seite 52.8
-
Hand
Tools
52.9eng/OP www.hhw.deFax order hotline: +49 6204 739-1217a = Sales are restricted to the packaging units mentioned in the catalogue. Purchase orders must be in units.# = partly extent in stock.
Phillips screwdrivers PH
0Type Round blade, through-hardened, glossy nickel-plated. Multi-component handle with extra largesoft zone and hanging hole.
Quality Blade made of chrome-vanadiumsteel.
52391
Set contents Size x blade length Type 52391 … mm 3-piece 1 x 80 / 2 x 100 / 3 x 150 in cardboard box 201
Phillips screwdrivers PH
+ TypeDrive: DIN 5260 PH, ISO 8764 PH. Round blade,glossy nickel-plated, through-hardened. Withimpact-proof plastic square handle, chemical andoil-resistant, made of cellulose acetate, red.
UseFor phillips recess head screws.QualityBlade made of chrome-vanadium-molybdenumsteel.
52396
Phillips screwdrivers PH
+TypeDrive: DIN 5260 PH, ISO 8764 PH. Round blade,through-hardened, matt-chrome finish. ChromTop®
tip. SoftFinish® handle with roll-off protection.
UseFor phillips recess head screws.QualityBlade made of high-quality chrome-vanadium-molybdenum steel.
52398
Set contents Size x blade length Type 52400 … mm 3-piece 1 x 80 / 2 x 100 / 3 x 150 in cardboard box 101
Size Blade length Overall length 52392 … mm mm 2 100 219 203 3 150 269 204
Size Blade length Overall length 52392 … mm mm 0 60 146 201 1 80 187 202
Size Blade length Overall length 52396 … mm mm 2 100 205 103 3 150 265 104
Size Blade length Overall length 52396 … mm mm 0 60 135 101 1 80 175 102
Size Blade length Overall length 52398 … mm mm 2 100 218 205 3 150 274 208
Size Blade length Overall length 52398 … mm mm 0 60 164 201 1 80 191 202
Size Blade length Overall length 52405 … mm mm XL 2 300 398 107 3 150 262 108 4 200 312 109 01 25 79 110 02 25 79 111
Size Blade length Overall length 52405 … mm mm 0 60 141 101 1 80 178 102 L 1 200 298 103 XL1 300 398 104 2 100 205 105 L 2 200 305 106
52391 - 52392
52398
sTypeDrive: DIN 5260 PH, ISO 8764 PH.Round blade, nicromatt, with Lasertip (size 1 - 3up to 200 mm blade length) to prevent slipping outof the screw and Kraftform handle with hard andsoft zones as well as roll-off protection.
UseFor phillips recess head screws.QualityBlade made of 73 Mo V 5 2.
Note:For blade length 25 mm, handle made of single-component material.
52396
Phillips screwdrivers PH
52405 110-111
52405
52400 - 52405
52_HHW_Katalog_2015_eng 03.09.15 08:48 Seite 52.9
-
Hand Tools
52.10 eng/OPwww.hhw.deFax order hotline: +49 6204 739-1217 a = Sales are restricted to the packaging units mentioned in the catalogue. Purchase orders must be in units. # = partly extent in stock.
Phillips screwdrivers PH
xTypeDrive: DIN/ISO 8764-1. Round blade, matt-chrome finish, through-harde-ned, burnished tip. Ergonomic 3-component handle,impact-proof. Permanent colour coding on bothhandle ends (for PH = red).
Use For phillips recess head screws.QualityBlade made of vanadium-extra steel.
52419 302-303
Size Blade length Overall length 52419 … 52420 … mm mm 0 60 182 301 1 75 197 302 L 1 200 322 # 303 2 100 222 304 L 2 200 322 305 3 150 272 306 01 25 83 201 02 25 83 202
52419 304-306
52420
52419 301
Phillips screwdrivers PH
+TypeDrive: DIN 5260 PH, ISO 8764 PH.Round blade, full-length, glossy nickel-plated,through-hardened, with hex bolster for additionaltorque. Wooden handle made of sealed beechwood. Impact head with leather cap, therefore nodamage to end of handle.
UseFor phillips recess head screws.QualityBlade made of chrome-vanadium steel.
52421
Phillips screwdrivers PH
0Type Drive: DIN 5260 PH, ISO 8764 PH. Hexagonal blade with hex bolster for additionaltorque, through-hardened, matt-chrome finish,blackened tip. Multi-component handle with extra large softzone and hanging hole.
Quality Blade made of chrome-vanadium-molybdenumsteel.
52437
Phillips screwdrivers PH
+Type Drive: DIN 5260 PH, ISO 8764 PH.Hexagonal blade with hex bolster for additional torque,through-hardened, matt-chrome finish. ChromTop® tip.SoftFinish® handle with roll-off protection.
Use For phillips recess head screws. Quality Blade made of high-quality chrome-vanadium-molybdenum steel.
52438
Size Blade length Overall length 52421 … mm mm 3 150 270 103 4 200 330 104
Size Blade length Overall length 52421 … mm mm 1 80 180 101 2 100 205 102
Size Blade length Overall length 52437 … mm mm 3 150 262 203
Size Blade length Overall length 52437 … mm mm 1 80 180 201 2 100 212 202
Size Blade length Overall length 52438 … mm mm 3 150 268 103
Size Blade length Overall length 52438 … mm mm 1 80 186 101 2 100 213 102
Set contents Size x blade length Type 52437 … mm 3-piece 1 x 80 / 2 x 100 / 3 x 150 in cardboard box 200
52419 - 52420
52421
52437
52438
Phillips screwdrivers PH │ ESD/EGB phillips screwdriver PH
52_HHW_Katalog_2015_eng 03.09.15 08:48 Seite 52.10
-
Hand
Tools
52.11eng/OP www.hhw.deFax order hotline: +49 6204 739-1217a = Sales are restricted to the packaging units mentioned in the catalogue. Purchase orders must be in units.# = partly extent in stock.
Phillips screwdriver set PH (3-piece)
+TypeDrive: DIN 5260 PH, ISO 8764 PH. Hexagonal blade with hex bolster for additionaltorque, through-hardened, matt-chrome finish.ChromTop® tip. SoftFinish® handle with roll-offprotection and solid steel cap.
UseFor phillips recess head screws.QualityBlade made of high-quality chrome-vanadium-molybdenum steel.
52439
Set contents Size x blade length Type 52439 … mm 3-piece 1 x 80 / 2 x 100 / 3 x 150 in cardboard box 201
Phillips screwdriver PH/The chisel-screwdriver
sTypeDrive: DIN 5260 PH, ISO 8764 PH.Full-length hexagonal blade, impact cap andhex bolster for additional torque. Black Point tip,exceptionally tough tempered. Kraftform Handle with hard and soft zones as well as roll-offprotection.
UseFor phillips recess head screws.QualityBlade made of 73 Mo V 5 2.
52443
Phillips screwdrivers PH
sTypeDrive: DIN 5260 PH, ISO 8764 PH.With Lasertip (size 1 - 3) to prevent slipping out ofthe screw, hexagonal blade, nicromatt, hex bolsterfor additional torque for size 1 - 3 and Kraftformhandle with hard and soft zones as well as roll-offprotection.
UseFor phillips recess head screws.QualityBlade made of 73 Mo V 5 2.
52444
ESD/EGB phillips screwdriver PH
sTypeDrive: DIN 5260 PH, ISO 8764 PH. Round blade,Black-Point tip, handle with roll-off protection.UseFor phillips recess head screws. For working onelectrostatically endangered electronic components.Complies with EN 100-015 Part 1.QualityBlade made of high-alloyed special steel.
52445 101-102TypeWith turnable cap for rapid twisting.
52445 104TypeWith Kraftform handle with hard and soft zones. 52445 104
52445 101-102
Size Blade length Overall length 52443 … mm mm 3 150 262 104 4 200 317 105
Size Blade length Overall length 52443 … mm mm 1 80 178 102 2 100 205 103
Size Blade length Overall length 52444 … mm mm 2 100 205 103 3 150 262 104
Size Blade length Overall length 52444 … mm mm 0 60 141 101 1 80 178 102
Size Blade length Overall length 52445 … mm mm 2 100 198 104
Size Blade length Overall length 52445 … mm mm