60 linear suspended direct/indirect

5.6

"

AA

AB

x2x2

x2 x8x6x6

2.4"

AD

Strain Relief BushingStrain Relief Bushing

Power CablesPower Cables

AF

BushingPower Cables

2" Canopy kit

5" Canopy kit

Housing

JoinerJoiner

HousingHousing

Joiner

Gear Tray - Indirect

Gear Tray - Direct

*slightly compress if needed

Gear Tray Mounting Screws

Gear Tray Mounting Screws

Gear Tray

Gear Tray*slightly compress

if needed

Endcap

Housing

Diffuser

Up to 96"

0.50"

0.35"

0.50" Suspension Points

Power feed cables

Over 96" 0.50" 0.50" 0.50"

0.35"

Suspension Points

Power feed cables

Suspension Points

Suspended

Phillips Head Screwdriver#2 Screwdriver

Wire Connectors

Wire Strippers

M3 Hex head Allen Key

Mounting Screws

LOCATE AND REVIEW ANY CONSTRUCTION PLANS AND INTERLUX RECORD DRAWINGS FOR ALL FIXTURE RUNS. It is recommended to locate and lay out all components for each fixture "run". A fixture run typically consist of endcaps, joiners, canopy kits, lengths of housings with diffusers, and lengths of gear trays (satellite - direct, satellite -

indirect and master). BE SURE TO IDENTIFY ALL CORRECT LENGTHS FOR EACH FIXTURE RUN.

Step 1&2: Turn off Power before Installing. Remove diffusers from housing and lay off to the side (ensure diffusers are stored in a place where they will not be damaged). Mount 4" junction box and suspension canopy in ceiling in accordance with drawing below. Suspension holes (1/4") and power feed hole (7/8") are pre-drilled into housing, canopy ceiling spacing is equal to suspension hole spacing on fixture(s).

Step 5: (If single housing skip this step) Place one straight joiner on each side ofhousing as seen below. Tigthen set screws using allen key.

Step 6: (If single housing skp this step) Insert airfcraft cable into cable gripper on nexthousing. Then, slide joiners across housing seam so they are joining both housings. Tighten set screws on joiners. Repeat steps 5-6 until all housing are installed and leveled.

Step 7: Feed power cables into housing. Install Gear Trays making electricconnections first, then insert gear tray into housing. Refer to pages 2&3 for wiring diagrams if needed. Refer to record drawings for gear tray placement. Secure gear tray to housing using screws in pre-drilled holes. If needed, slightly compress sides of housing to properly align gear tray holes with housing. Repeat this step until all gear trays are installed.

Step 8: Install Endcaps on each end of fixture run. Re-install diffusers and ensurethey are flush along the length of the run. Energize and test for proper operation.

2" Canopy Kit

Powered 5" Canopy Kit

Housing (Feed and Non-Feed)

Master Gear Tray - Direct

Satellite Gear Tray (Direct and Indirect)

Joiner(2 per joint)

Step 3 & 4: Make wire connections in junction box and drop down feed power cable. Mount cross bar to junction box. Insert aircraft cable through coupler and attachto cross bar with threaded rod. Repeat this step for non-power suspension point. Install cable gripper from suspension kit to locations on top of housing using supplied hardware from suspension kit. Insert aircraft cable into power feed housing to suspend it at both locations. Adjust suspension to level the housing.

Diffuser

Junction Box

M4x6 GT Screw

Endcap Kit

Cable GripperJunction Box

Cross Bar

Canopy Plate

Coupler

Aircraft Cable

Threaded Rod

Aircraft Cable

THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF Inter-lux. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF Inter-lux IS PROHIBITED.

PROPRIETARY AND CONFIDENTIAL

FINISH:White (Standard)

WG 60LDI-S

SHEET 1 OF 3DRAWING NOT TO SCALE

INSTALLATION INSTRUCTIONS

REV N/C

WARNING:FAILURE TO COMPLY WITH THE

INSTALLATION INSTRUCTIONS MAYRESULT IN DEATH OR SERIOUS INJURY

WARNING:INSTALL PRODUCT IN ACCORDANCE

WITH LOCAL AND NATIONAL ELECTRICALCODES BY A QUALIFIED ELECTRICIAN

OR ELECTRICAL CONTRACTOR.

CAUTION:INTER-LUX IS NOT RESPONSIBLE FOR THE

STRUCTURAL INTEGRITY OF THE BUILDING TOSUPPORT THE LUMINAIRE. ADDITIONAL BACKING

MAY BE REQUIRED.

*Inter-lux reserves the right to make changes to this product and related installation instructions at any time without prior notice.

MOUNTING OPTIONS

ISOMETRIC VIEWS ITEMS NEEDED (SUPPLIED BY OTHERS):PACKAGE MAY INCLUDE: (refer to package list to identify parts)

60 Linear Suspended Direct/Indirect INSTALLATION INSTRUCTIONS

Phone: (410)381-1497 Web: www.inter-lux.com

WEIGHT:

CAUTION:THIS IS AN ELECTRONIC DEVICE. CARE MUST BE TAKEN

DURING STORAGE AND HANDLING. STORE IN A CLEAN, COOLAND DRY LOCATION. ELECTROSTATIC DISCHARGE (ESD) CAN

HARM THIS PRODUCT. AVOID STATIC DISCHARGE WHILEHANDLING THIS PRODUCT.

MOUNTING DIMENSIONS

WARNING:READ ALL SAFETY INSTRUCTIONS

INCLUDED WITH LUMINAIRE BEFOREINSTALLING LUMINAIRE.

Red Blue Green Black White

Positive Negative Ground Line Neutral

Purple Grey

Dimming + Dimming -

Osram

25'

101'

63'

39'

< 48W < 72W < 96W < 40W

25'

15'

40'

60'151'

18'

29'

47'

75'

95'

59'

37'

#12AWG

#14AWG

#16AWG

#18AWG

Wire Gauge LutronMaximum Lead Length

Standard Non-Dimming/DFPN Dimming D3W 1% Dimming

DES 1% Dimming 0-10V Dimming

To L

ine

Vol

tage

(Sta

ndar

d)

To F

orw

ard

Pha

se C

ontro

l (D

FPN

)

To 3

-Wire

Dim

min

g C

ontro

lTo

Lin

eV

olta

ge

To L

ine

Vol

tage

To E

cosy

stem

Dig

ital L

ink

To 0

-10V

Dim

Con

trol

NOTE: ALL DRIVERS ARE INTER-LUX PROVIDED. FOR NON INTER-LUX DRIVERS PLEASE REFER TO DRIVER MANUFACUTERS.THE USE OF NON INTER-LUX DRIVERS VOIDS PRODUCT WARRANTY



FINISH: White (Standard)

WG 60LDI-S

SHEET 2 OF 3DRAWING NOT TO SCALE

Driver Wiring Diagrams

REV N/C








MAY BE REQUIRED.



WEIGHT:




Maximum Wiring Distance*



*Actual Voltage drop to be calculated by installer

Wiring Key

Ground (Green)

Dimming - (Grey)

Line (Black)

Neutral (White)

Switch/Dimmer(if applicable)

AC Power

Ground (Green)

Power Supply

Dimmed Hot (Black)

Neutral (White)+VDC

-VDC

LED lightengine

Ground (Green)

Power Supply

Switched Hot (Black)

Neutral (White) LED lightengine

Dimmed Hot (Orange)

Ground (Green) Power Supply

Switched Hot (Black)

Neutral (White)

LED lightengine

E1 (Purple)E2 (Purple)

Ground (Green) Power Supply

Line (Black)

Neutral (White)

Dimming + (Purple)

Dimming - (Grey)

LED lightengine

+VDC

-VDC

-VDC -VDC

+VDC +VDC

Master Gear Tray


Dimming + (Purple)

RED AND BLUE (LOW VOLTAGE) TO LED BOARD

GREEN GROUND TERMINAL FIXED TO GEARTRAY

RED/WHITE STRIPES AND BLUE/WHITE STRIPES (LOW VOLTAGE) TO INDIRECT GEAR TRAYS HIGH VOTLAGE (BLACK,

WHITE, GRAY VIOLET)HIGH VOTLAGE (BLACK, WHITE, GRAY VIOLET)

LOW VOTLAGE (RED, BLUE)LOW VOTLAGE (RED, BLUE)

Driver Driver

MASTER DIRECT

DIRECT HIGH VOLTAGE CIRCUIT (BLACK, WHITE, GREEN, GRAY, VIOLET, RED, BLUE) INDIRECT HIGH

VOLTAGE CIRCUIT (BLACK/WHITE STP, WHITE/RED STP, GRAY/WHITE STP, VIOLET/ WHITE STP, RED/WHITE STP, BLUE/WHITE STP)

SATELLITE HARNESS FOR DIRECT HIGH VOLTAGE CIRCUIT

FEED THRU HARNESS FOR INDIRECT HIGH VOLTAGE CIRCUIT

GREEN GROUND TERMINAL FIXED TO GEARTRAYRED AND BLUE (LOW VOLTAGE) TO LED BOARD

DIRECT HIGH VOLTAGE CIRCUIT (BLACK, WHITE, GREEN, GRAY, VIOLET, RED, BLUE)

INDIRECT HIGH VOLTAGE CIRCUIT (BLACK/WHITE STP, WHITE/RED STP, GRAY/WHITE STP, VIOLET/ WHITE STP)

RED/WHITE STP AND BLUE/WHITE STP (LOW VOLTAGE) TO LED BOARD

INDIRECT LOW VOLTAGE CIRCUIT (RED/WHITE STP, BLUE/WHITE STP)

SATELLITE DIRECT

SATELLITE INDIRECT

BLACK, WHITE, GRAY, VIOLET, GREEN

HIGH VOLTAGE PASS THROUGH HARNESS FOR INDIRECT (STRIPPED COLOR WIRE)

LOW VOLTAGE TO GEAR TRAY LEDS


HIGH VOLTAGE PASS THROUGH HARNESS FOR DIRECT (SOLID COLOR WIRE)



HIGH VOLTAGE HARNESS FOR DIRECT (SOLID COLOR WIRE)

RED STP AND BLUE STP TO INDIRECT GEAR TRAY

HIGH VOLTAGE HARNESS FOR INDIRECT (STRIPPED COLOR WIRE)

RED STP AND BLUE STP INDIRECT (LOW VOLTAGE)

POWER FEEDS FROM CANOPY

DRIVER FOR INDIRECTDRIVER FOR DIRECT

GEAR TRAY SATELLITE DIRECT (SA) GEAR TRAY DOUBLE MASTER (2XMA)

GEAR TRAY SATELLITE INDIRECT (SA) GEAR TRAY SATELLITE INDIRECT (SA)

CABLE GRIPPER AND AIRCRAFT

RED STP AND BLUE STP INDIRECT (LOW VOLTAGE)



FINISH: White (Standard)

WG 60LDI-S

SHEET 3 OF 3DRAWING NOT TO SCALE REV N/C








MAY BE REQUIRED.



WEIGHT:







WIRING DIAGRAM

60 linear suspended direct/indirect

Documents