616 gsr driftwood log set installation instructions (sku · 2013-04-30 · 616 gsr packing list ......

616 GSR Driftwood Log Set Installation Instructions (SKU 94500949)

of 11 17601714.docx — 8/23/12 © Travis Industries, Inc.

Compatibility

616 GSR

Packing List

7‐Piece Driftwood Log Set (not shown)

Standoff Pack: Includes (4) Log Support Brackets, (6) 10‐24 Nuts

Rear Burner Deflector, NG/LP Rear Air Deflector

Bag of Rock Wool, Bag of Embers

WARNINGS

Make sure the gas control valve is OFF and the heater is cool before conducting service.

Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

If using propane (LP), convert the appliance before installing the logs (see the owner’s manual for details).

Do not use crushed glass media with this log set. It causes excess sooting. Use included rock wool.



Burner Installation

NOTE: The insert should be in place, with the gas line and vent attached, and the firebacks installed (see owner’s manual for further details) before proceeding.

1. Remove the rear burner as shown below.

2. Remove the 3 screws from the back of the rear burner using a ¼” nutdriver.

NOTE: Remove the attachment screw first.



3. Attach the rear air deflector to the rear burner with the screws removed in the previous step.

NOTE: Verify the correct air deflector according to your fuel type IMPORTANT: Make sure the air deflector holes are aligned, if they do not align flip the deflector over.

NG Installation

LP Installation

4. Replace the rear burner and secure with the attachment screw.

This notch in the LP deflector differentiates it from the NG air deflector.

The two tabs on the rear burner rest on top of the front burner.



5. Install the rear burner deflector.

6. Attach the log supports with the 6 included nuts.



Rock Wool Placement

7. Place the rock wool as follows:

a. Brush the rock wool using a stiff brush in a loose, gauze‐like layer.

TIP: Hold the rock wool in a tight wad with one hand while brushing with the other.

Note how the rock wool is approximately 1/8” thick over the burner ports.

TIP: Feel free to apply a generous amount of rock wool to gain a darker flame and a brighter coal bed.



Log and Ember Chunks Placement

The logs are fragile, especially after being exposed to heat.

IMPORTANT: The burner must be correctly positioned before installing the logs. Make sure the burner is fully seated.

8. Place the rear log as shown below.

Move the log forward until it rests against the tabs on the burners.



9. Place the left middle log.

10. Place the right middle log.



11. Place the left cross log.

12. Place the pilot log.



13. Place the front right log.

14. Place the center cross log.



15. Place the ember chunks. Note that roughly half the bag of embers is left over.

Make sure that the ember chunks DO NOT cover any burner ports.

TIP: The ember chunks should be placed so as to hide any sheet metal parts, rivets, and screws.

16. Re‐apply the rock wool over the ember chunks along the front burner and between the two front logs for a natural look.

TIP: Natural gas (NG) can use more rock wool than propane (LP).

NOTE: Initial application of rock wool may cause “matting” over burner ports. Turning the unit on and then off again will loosen the rock wool, resulting in a better flame.



17. Check the exhaust restrictor setting before finalizing the installation.

Restrictor Settings

Driftwood Logs

Natural Gas Short Vent (25’ or less)

#1

Natural Gas Tall Vent (25’ or more)

#3 (stock)

Propane Short Vent (25’ or less)

#1

Propane Tall Vent (25’ or more)

#3 (stock)

Finalized installation:

18. Test‐burn the insert with the glass frame in place before finishing the installation. See the owner’s manual for details on finalizing the installation (adjusting the air shutter, etc.).

616 gsr driftwood log set installation instructions (sku · 2013-04-30 · 616 gsr packing list ......

Documents