7-speed direct shift gearbox (dsg_0am) - ross-tech wiki

Upload: vuk-krstajic

Post on 08-Mar-2016

386 views

Category:

Documents


11 download

TRANSCRIPT

  • Search:

    Skip to contentShop Info F.A.Q. Download/Update Manual Upgrades Literature

    7-Speed Direct Shift Gearbox (DSG/0AM)From Ross-Tech Wiki

    General Information about this Transmission can be found in the Wikipedia entry (http://en.wikipedia.org/wiki/Direct-Shift_Gearbox) . Additional information can be found in the Official Factory Repair Information.

    Our Current 0AM-300-04x.lbl label file needs a facelift and the 0AM is not used in the NAR market at thistime, so we don't have access to a TCM in a real car. Control Module Maps from these units would beappreciated and that function is explained in detail on the following page: Control Module Maps Please submita complete Auto Scan (http://www.ross-tech.com/vcds/tour/autoscan.html) with the control module maps whenpossible.

    This should be obvious but the procedures on this page do NOT apply to transmissions other than 0AM. Forexample, longitudinal 7 speed DSG's like the 0B5 used in the B8 S4 use a different procedure.

    Contents1 Coding2 Basic Setting3 Special Procedures

    3.1 Defined Test Drive3.1.1 Special Notes

    CodingWhen replacing this Mechatronic unit, simply copy the coding from the original Auto-Scan and paste itinto the New Coding section of the replacement followed by clicking [Do it! (http://www.ross-tech.com/vcds/tour/recode_screen.html) ].

    Basic SettingPrerequisites:

    No Fault Codes stored in the TCMTemperature 30C - 60C. The Measuring Block value for G510 is found in group 011.1

    7-Speed Direct Shift Gearbox (DSG/0AM) - Ross-Tech Wiki http://wiki.ross-tech.com/wiki/index.php/7-Speed_Direct_Shift_Gearbox...

    1 of 3 11-Feb-16 12:02

  • Selector Lever in PIgnition ON, Engine OFFParking brake appliedBrake Pedal operated (hold for the whole procedure)Throttle Pedal not operatedSee the Special Notes if the Mechatronic unit needs to be replaced.

    NOTE: Be sure to perform the following steps in the sequence shown, followed by the defined test drive.

    [Select][02 - Transmission][Basic Settings - 04]Group 060[Go!][ON/OFF/Next] may be necessary

    The live data should display 4 | 0 | 0 in Basic Settings. This may take up to 2 -to- 5 minutes.After the 4 | 0 | 0 results are displayed, start the engine immediately and allow it to idle. If 4 | 0 | 0 is notshown do NOT start the engine, something is wrong with the procedure or the transmission.

    It is normal for the transmission to make noise while the tolerances are adapting. Do not exit orabort the Basic Settings sequence prematurely if you hear clacking noises. This is similar to the02E 6-Speed DSG.

    The live data should display 254 | 0 | 0 to confirm a successful Basic Settings after 3 -to- 6 minutes.254 | 7 | 0 alone would Not be complete yet and 255 | 0 | 0 would indicate the basic settings wasinterrupted or failed.

    [Done, Go Back]Switch off Ignition, wait for a few seconds and switch it back on.[Fault Codes - 02]Check and clear any fault codes.[Close Controller, Go Back - 06]Perform the Defined Test Drive below.

    Special ProceduresPrerequisites:

    Transmission fluid greater than 30* C. The Measuring Block value for G510 is found in group 011.1Do Not use Cruise Control.

    Defined Test Drive

    Suggested test drive after replacing the Mechatronics module/TCM or successful basic setting.

    With the shifter in Drive accelerate at half throttle to 2nd gear.Stop and repeat half throttle acceleration into 2nd gear.

    7-Speed Direct Shift Gearbox (DSG/0AM) - Ross-Tech Wiki http://wiki.ross-tech.com/wiki/index.php/7-Speed_Direct_Shift_Gearbox...

    2 of 3 11-Feb-16 12:02

  • Stop followed by shifting into reverse and backing up two times.Stop followed by driving in each forward gear using the Tiptronic shifters for no less than 3 seconds pergear.

    The next portion of the drive must be done in any group choice of the following gears to maintain the properRPM and maintain a safe driving distance on the road:

    A = Gears 4th or 6th (4th is preferred)B = Gears 3rd, 5th or 7th (5th is preferred)

    Using the Tiptronic shifters maintain the range of 2,000 -to- 4,500 RPM and drive in each gear group (Aand B) for no less than one full minute (two minutes are preferred). Use variable accelerator pedalpositions but accelerate to full throttle at one point in each gear group during this one minute process.

    MVBs 180.1 -and- 200.1 should confirm clutch adaptations with values of 3 or greater. If any portion ofthe adaptation is not completed it should finish on its own with normal driving.

    NOTE: If the test drive cannot be performed in the recommended way or the necessary time, any remainingadaptations will be performed automatically during normal driving.

    Special Notes

    Use the Official Factory Repair Information if the Mechatronic unit needs to be replaced.The Removal Position Basic Setting group number is 062.The Neutral Position Basic Setting group number is 061.

    Some modules do not require the use if the [ON/OFF/Next] button. If an Error is displayed after clickingthe button, or the Basic Settings status does not switch to On, let the selected group and procedure finishon its own.

    It is normal for the transmission to make noise while the tolerances are adapting. Do not exit or abort theBasic Settings sequence prematurely if you hear clacking noises.

    If Registered Users experience difficulty with the Basic Settings procedure, please send the completeAuto-Scan in addition to the vehicle repair history to us directly via email (mailto:[email protected]) .

    Retrieved from "http://wiki.ross-tech.com/wiki/index.php?title=7-Speed_Direct_Shift_Gearbox_(DSG/0AM)&oldid=7948"Category: Transmissions

    Unless otherwise noted, all content on this site is Copyright 2000-2010 by Ross-Tech LLC. All rightsreserved."VCDS" is a Registered Trademark of Ross-Tech, LLC.Ross-Tech is not affiliated with the Volkswagen Group in any way.

    7-Speed Direct Shift Gearbox (DSG/0AM) - Ross-Tech Wiki http://wiki.ross-tech.com/wiki/index.php/7-Speed_Direct_Shift_Gearbox...

    3 of 3 11-Feb-16 12:02