727hv3 mu en

Operation Manual

Stand-alone Controller

AR-727H

2005/12/16

1. Add - Card ID 2. Add - RF-learn 3. Suspend - Addr4. Suspend – ID #5. Delete - Addr 6. Delete – ID# 7. Recover - Addr8. Recover –ID # 9. Antipass Group

1.Add/Delete

2.User Setting

3.Parameters(1)

4.Parameters(2)

5.Tools

6.Quit

7.Quit & Arming

Function Menu

1.Node ID 2.Auto Open Zone 3.Door Relay Tm 4.Door Close Tm 5.Alarm Relay Tm 6.Alarm Delay Tm 7.Arming Delay Tm 8.Arming PWD 9.Arming Pulse

1.Password 2.Access Mode 3.Extend Options4.Single Floor 5.Multi Floors

1.Auto Relock 2.Egress(R.T.E.) 3.Attendance 4.Master Node 5.Force Open… 6.Close & Stop 7.Anti-passback 8.Duress Code 9.Factory Reset 0.Key(#) is Bell

1.Language 2.Master Code 3.Master Range 4.Terminal Port 5.AR721R32 Port 6.Open TimeZone 7.Informations 8.Clock Setting 9.Control Mode 0.View Events

1

Table of Contents Page

1. Main Feature --------------------------------- 4 2. Control Mode --------------------------------- 5 3. Notice --------------------------------- 6

How to know card ID of user address? -------------------------------- 6 LCD display show card ID except user address (ex. 00005) when the user flash card? -------------------------------- 6 How to know how many users in the system now? -------------------------------- 6 How to know which item at your hand? --------------------------------- 7 How to start/suspend (auto open zone)? ---------------------------------- 7 How to disarming? ---------------------------------- 7 How to restore master code to the factory default?--------------------------------- 7 How to reset all parameter to the factory default?----------------------------------- 7 How to set the time on AR-727H? ---------------------------------- 8 How to enable bell output? ----------------------------------- 8 How to check the historical records? ------------------------------------ 8

4. Front Panel & Functions ------------------------------------- 9 5. Mode 4 / 8 / 9 ------------------------------------- 10

5.1 Card Editing ------------------------------------- 10 5.2 Access Mode ------------------------------------- 11 5.3 Duress function ------------------------------------- 12 5.4 Force on/off code ------------------------------------ 12

6 Mode 6 ------------------------------------ 14 6.1 Card editing ----------------------------------- 14 6.2 Access mode ----------------------------------- 14

7 Quick Guide ----------------------------------- 15 8 Function description ----------------------------------- 16 9 Special designed --------------------------------- 19

9.1 Connecting one AR-727H with 2 AR-661U for Anti-pass-back ------------- 19 9.2 How AR-727 connects with a weigand reader (AR-721K, AR-721U, AR-661U) and to apply to anti-pass back --------------------------------- 20 9.3 How to set multi AR-727H connects with a net controller and to apply to anti-pass-back -------------------------------- 20 9.4 How to setting the weigand reader (AR-721U, AR-721K, AR-661U) and AR-727H at the same net controller to apply to the anti-pass-back -------------------------------- 20 9.5 How to set that user arrive single floor or multi-floor -------------------------- 21

2

9.6 How to set AR-401RO16 parameter ------------------------------ 22 10 Installation -------------------------------- 23

10.1 Step -------------------------------23 10.2 Installation Notice --------------------------------- 23

11 Wiring --------------------------------- 26 12 Installation diagram -------------------------------- 27

12.1 Magnetic lock -------------------------------- 27 12.2 Electric bolt lock -------------------------------- 28 12.3 Electric strike -------------------------------- 29 12.4 Magnetic door contacts and alarm system ---------------------------------- 30 12.5 Wiegand reader -------------------------------- 31 12.6 Networking installation -------------------------------- 32 12.6.1 two set of AR-716EV2 parallel installation ----------------------------- 33 12.6.2 AR-716EV2, AR-829E and AR-727H

parallel installation ---------------------------- 34 12.7 Lift controller AR-401RO16 installation ------------------------------- 35

12.1 AR-727H & AR-801CM & PC installation ------------------------------- 36 12.2 RS-232 Printer --------------------------------------------------- 37

13 Software Application ----------------------------------------------------- 38 14 Troubleshooting --------------------------------------------------------- 39 15 Return of Products ------------------------------------ 39 16 Warranty --------------------------------- 39 17 Transponder Record Table ---------------------------------- 40 18 Specification -------------------------------- 41

3

1. Main Features With waterproof, could be installed outside.

Special feature for stand-alone use:

◎ Keep last 1200 transactions

◎ Editable 2 time zone for door release purpose

◎ Controller needless anti-pass back:: AR-727H supports anti-pass back with its external reader.

Master Cards range assignable.

Unlimited Site Code.

Clear and big LCD panel with 4 line messages. (128 * 64 graphic)

One RS-485 Port supported for networking(via controller or directly).

Built-in one Door sensor and Arming on/off input.

Support with keypad locks immd & all cards entrance allowance before cards editing finished.

Support remote operation to relays on networking controller AR-716EV2/AR-716Ei via Force on/off code.

Support with Auto-relock automatically and keypad locked if continuous wrong code inputted.

Control mode, card capacity and card type assignable by user directly.

Built-in a proximity reader, a external wiegand reader port and IC card reader (optional).

Auto-discriminating between stand-alone & networking system, AR-727H could connect with controller AR-716EV2, AR-716Ei to have multi-door anti-pass back.

Alarm function available. (Tamper, Force entrance, door open too long)

Universal serial port supported for LED display, printer, lift controller, etc

4

2. Control Mode

AR-727HV3 MODE 4

Stand-alone MODE 6

Stand-alone MODE 8

Stand-alone Networking

Card user Capacity

1024 65536 1024 Depend on Controller

Access Mode Card only

Card & PIN User nbr. & PIN

Card only Card only

Card & PIN PIN only

Depend on

Anti-pass Back Single door × Single door Multi-door

anti-pass back (16 doors)

Control Mode in Networking

Mode 4 × Mode 8 Mode 4

Or Mode 8

Note WG32 WG 16 WG32 WG32

Lift control 32 stop

1024 card users×

32 stop 1024 card user

32 stop 1024 card

users How to set Mode 4 ,Mode 6 , Mode 8 and Mode 9:

Step1: * + 1 2 3 4 5 6 + # enter the “FUNCTION MENU” Step2: Tool / control mode (command：59)

1:M4 2:M6 3:M8 4:M9, input Mode value. tags format—1:EM 2:SOYAL, input card value.

Note: 1. M4=M9 In AR-727HV3 version. 2. Changing control mode “from Mode 6 to Mode 4” or “from Mode 4 to Mode 6”, it is

necessary to delete all card user data first. Depend on controller: For example, controller AR-716EV2 has 15,000 card users

capacity. Lift control: For 1024 card users, everyone could be assigned for single floor or

multi-floor access.

5

3. Notice Keep AR-727H away from the followings:

Keep away from magnets or any magnetized items. Do not apply strong shock to 727H

After flash master card and press F1 F2 F3 F4 or # within 2 seconds can enter the “FUNCTION MENU”. Master Cards range assignable. Default value: user address 00000 – 00004.

Each card has 10 digits code, including Site code (5 digits) and Card code (5 digits). Neither the Site Code nor the Card Code numbers can be 0.

After card editing finished, Site Code and Card Code is not important anymore. System will require a USER ADDRESS instead.

User can request to exit through the controlled door without using transponder (and without causing an alarm condition), by pressing an exit button. This will operate the door relay for the programmed door relay release time & stop alarm.

How to know card ID of user address? (For example: which card ID do we want to know user address 00003)

Step1: * + 1 2 3 4 5 6 + # enter the “FUNCTION MENU”

Step2: Add/Delete (command 1) Step3: Add / Card ID (command 1) Step4: Enter user address 00003, then you will see card ID. LCD display show card ID except user address (ex. 00005) when the user flash card?

How to do? Step1: * + 1 2 3 4 5 6 + #

enter the “FUNCTION MENU” Step2: Parameters (1) (command 3)

Step3: Node ID (command 1) Step4: Set Node ID Step5: Then, the system will ask if show card ID? 1. No 2. WG 3. ABA 4. HEX Cur.: 1 Step6: If select 2. WG, for example as follows: User address 00005 for card ID 00020:25000 When user flash card, LCD display will show both user address 00005 and card ID 00020:25000. Note that CPU version must be at least 4.1 or up. How to know how many users in the system now? (Not including suspend card)


Step2: Tools (command 5) Step3: Informations (command 7) AR-727H Ver 3.4 Users: 00010 (There are already 10 users in the system) How to know which item at your hand?

6

(For 125K system or Mifare system) Step1: * + 1 2 3 4 5 6 + #

enter the “FUNCTION MENU” Step2: Tools (command 5)

Step3: Informations (command 7) "AR-727H1356 V4.2""Users: 00000 ""Messages: " Or "AR-727H Ver 4.2 ""Users: 00000 ""Messages: " How to start/suspend (auto open zone)?

Step1: main manual Step2: tools (command 5) Step3: setting Open Time Zone (command 6) Step4: come back to main manual Step5: Parameters (1) (command 3) Step6: start Auto open zone function (command 2) Step7: Yes / No Note: The electronic lock would be locked until first one flash card on the reader when the system enter auto open time zone. And electronic lock will be locked that sensor feels door closed when system exit auto open time zone. How to disarming?

(1) User can be disarming by normal access mode once violating anti-pass-back resulting in alarm. (2) User can be disarming by valid card when alarm happen. (3) * + 1 2 3 4 5 6 + #

enter the “FUNCTION MENU” Step1: main manual

Step2: Parameters (2) (command 4) Step3: Close Door Stop Alarm (command 6), then enter 1: YES.

How to restore master code to the factory default (123456)? If the master code is forgotten it can be restored to the factory default (123456). Remove the AR-727H from the mounting plate, disconnect power, remove AR-727H CPU, install AR-727H-CLE CPU, and restore power about 10 seconds. Then disconnect power, remove AR-727H-LCE CPU, install AR-727H CPU, and restore power. How to reset all parameter to the factory default?


Step2: Parameters(2) (command 4) Step3: Factory Reset (command 9) Then, LCD display will show “Initial System……” message to reset all parameter to factory default. Note that CPU version must be at least 3.8 or up.

How to set the time on AR-727H?

7


Step2: Tools (command 5) Step3: Clock Setting (command 8) Step4: Input Date&Time YyMmDdHhMmSs How to enable bell output?


Step2: Parameter(2) (command 4) Step3: Key(#) is Bell (command 0) Step4: Press(#) On Bell 1:YES 2:No Data:0

Step5: Enter 1:YES How to check the historical records?

(1) Press * + 1 2 3 4 5 6 + # enter the “FUNCTION MENU”.

(2) “Tools (Command 5)” -> “View Events (Command 0)” (3) Then, you will see the following message from LED screen:

A 01/16 15:45:25 FRI 00001 001

User AddressWeek

TimeDate

Work Status :

A: Duty On

B: Duty Off

C: Overtime on

D: Overtime off

E: Break out

F: Break RTN

G: Go

H: Return

8

Serial Number

4. Front Panel Functions

Input ndicator Arming Green)

Alarm (Red)

Transmission: Receive (Green)

Send (Red)

Keypad Atte Press 1 time PresF1 Up Duty on BreaF2 Down Duty off BreaF3 Correct Overtime on Go F4 Overtime off Retu＊ Esc ＃ Enter Other:

◎ Press ＊ + Master Code (defauto enter “Function Menu”

◎ Before card editing finished, the + F4 for all cards entrance allow

◎ Press ＊ + ＃ to lock / unlock kFunctions: 1. System will automatically exit from

made within 30 seconds. 2. In FUNCTION MENU, LED [OK] w3. In card access mode, flashing qua

LED [OK] and LED [Reading] will shown [OK],

4. Flashing unqualified card on the uLED [ERROR] and LED [Readingmessage shown [Invalid Card!].

5. Green LED [ARMING] light up in “6. Red LED [ALARM] lights up if any7. Continuous wrong “PIN Code” or

seconds, LED [Error] light up and 8. Once Alarm arisen, user must pus

and return to standby state. 9. Transmission:

Receive [Green] lights up when it Send [Red] lights up when AR-727

a

]

“

ns

l

m

l

n

A

Lh

r

&

Error (Red)

OK(Green)

Reading (Green)

dance 2 times

k out k RTN

rn

t : 123456, changeable) + ＃,

aster could enter “Function Menu” and press ０ nce. eypad immd.

FUNCTION MENU, if no key or card entry is

ill flash continuously and quickly. lified card on the unit ight up, a beep sound and LCD panel message

it light up, two beeps sound and LCD panel

rming On”. abnormal condition arisen. Master Code” will make keypad locked for 30 CD panel shown [keypad Locked]. exit button or flashing qualified card to release

eceives message from PC or its external reader. H sends data to PC

9

5. Mode 4 / 8 Pre-explanation Arming PWD (4 digits)

Default value:1234 Could be setup via Function Menu (Function no. 38)

PIN Code (4 digits) Could be setup via Function Menu (Function no. 21) Or, via 701 Client \ Setting \ User card

Duress Code (4 sets, 4 digits) Networking System:

Default value:1111 ; 2222 ; 3333 ; 4444 Changeable via 701 Server\ Setting \ 701 Configuration \ Duress Code

Stand-alone System: Default value:4321 Changeable via Function Menu (Function no. 48)

Force on/off Code (4 sets, 4 digits) Networking System:

Default value:1111 ; 1111 ; 1111 ; 1111 Changeable via 701 Server\ Setting \ 701 Configuration \ Duress Code

5.1 Card Editing

After entering Function Mode, user uses following order to edit cards. Function Nbr.

Add→Card ID 11 Add→RF learn 12 Delete→Addr 15 Delete→ID# 16 Recover→Addr 17 Recover→ID# 18

How to edit ten pcs sequential cards? ( Default access mode is Card only) Step1: * + 1 2 3 4 5 6 + # enter the “FUNCTION MENU”

Step2: Add/Delete (command 1) Step3: Add→RF learn (command 2) Step4: Then, LCD display will show as follow: Please follow LCD display indicator to edit card Step5: InputStartAddr (0-00999)

Enter 1, start from user no. 1 Step6: Tag Uints (pcs) Must be Sequence (1-00999) Enter 10

Step7: Close Tag Into RF Area Present the lowest card code of card to the unit.

10

5.2 Access Mode Users can select one of the following access modes 5.2.1 Card Only

Access the door by flashing card

Open door & turn Arming on / off: Flash card, then press Arming PWD + F1

Not open door & turn arming on / off: Press ＊ + Arming PWD, then flash card

5.2.2 Card and PIN Flash card, then press PIN Code ＋＃

Open door & turn Arming on / off: Flash card, press PIN code & ＃, then Arming PWD + F1

Not open door & turn arming on / off: Not available How to set access mode of user is card and PIN? Step1: * + 1 2 3 4 5 6 + # enter the “FUNCTION MENU”

Step2: User Setting (command 2) Step3: Access Mode (command 2) Step4: Enter user number, Then, LCD display will show as follow:

1:Card 2:or PIN 3:& PIN 4:Pause Data: 1 Please select number 3: & PIN

Step5: Return to main menu to set the password of user Step6: User Setting (command 2) Step7: Password (command 1) Step8: Enter user number Then, LCD display will show as follow: Input 4 Digit No. Range:0001~9999 Data:

5.2.3 User address and PIN (Mode 4) Press keypad: User address (5 digit), then PIN code & ＃ Open door & turn Arming on / off: User address, press PIN code & ＃, then Arming PWD + F1 Not open door & turn arming on / off: Not available How to set access mode of user is card or PIN?



1:Card 2:or PIN 3:& PIN 4:Pause Data: 1 Please select number 2:or PIN

Step5: Return to main menu to set the password of user Step6: User Setting (command 2) Step7: Password (command 1) Step8: Enter user number

Then, LCD display will show as follow: Input 4 Digit No. Range:0001~9999 Data:

11

5.2.4 PIN only (Mode 8) Same as Card Only Or, press keypad ◎ Door access: PIN code (4 digit) ◎ Open door & turn Arming on / off:

PIN code & ＃, then Arming PWD + F1 ◎Not open door & turn arming on / off: Not available How to set access mode of user is PIN only?



1:Card 2:or PIN 3:& PIN 4:Pause Data: 1 Please select number 2:or PIN

Step5: Return to main menu to set the password of user Step6: User Setting (command 2) Step7: Password (command 1) Step8: Enter user number, Then, LCD display will show as follow:

Input 4 Digit No. Range:0001~9999 Data: 5.2.5 Change PIN code

AR-727H connects with PC, running 701 client and set PIN code variable. By user: Flash card, then press PIN code (4 digit) twice + ＃) By 701 client \ setting \ user card Not connecting with PC Entering Function menu \ User setting \ Password

5.3 Duress function This function could help users to send a message to the computer asking for help. Only available in networking state, running 701 Server and setting 4 sets of Duress code on

PC. (Anyone of these 4 sets is workable.) This function is not available for CARD ONLY access mode and mode 8 directly

4-digit PIN.

Access Mode Command Format Card Only Not available Card and PIN Flash card, then press Duress code & ＃ Users addr. and PIN (Mode 4)

Press user address, then Duress code & ＃

PIN Only (Mode 8) Duress code 5.4 Force on/off Code (4 sets, 4 digits)

Only workable in networking system, running 701 Server and setting 4 sets of Force code on PC. (Anyone of these 4 sets is workable.) User could press related code to turn on / off its connected equipment, diagram as below.

12

PC board of Controller AR-716EV2 / AR-727E

COM

JP4

V12CN5

DI.4

DI.2DI.1

DI.3

COM

D10D9

D11

K4RELAY

K3

D12

RELAY

JP3

K1

K3K4

K2K2

RELAYRELAYK1

Relay Code K1 16 K2 17 K3 18 K4 19

After access OK, press following order to turn on / off its connected equipment.

Access mode ON/Off Order

ON Flashing card＋Force code＋Code＋０＋＃ Card only

Off Flashing card＋Force code＋Code＋１＋＃

ON Flashing card＋User code ＋Force code＋Code＋０＋＃ Card + user

code Off

Flashing card＋User code ＋Force code＋Code＋１＋＃

ON User no. ＋User code ＋Force code＋Code＋０＋＃

User no. + user code (Mode 4)

Off User no. ＋User code ＋Force code＋Code＋１＋＃

ON User code ＋Force code＋Code＋０＋＃ User code only

(Mode 8) Off User code ＋Force code＋Code＋１＋＃ This function is good for force control television, air conditioning, audio, etc. by Relay-1, 2, 3, 4 on the multi-door networking controller. To avoid the conflict of the use of each controller relay, it is user responsibility to define each controller relay for one purpose use only.

13

6. Mode 6 6.1 Card Editing

Under Mode 6, the system built in card code from 00001 to 63200 itself, so user can only suspend or recover cards, not allowed to add or delete. The card which its card code is over than 63200 can’t be used under Mode 6. After entering Function Mode, user uses following order to edit cards.

Function Nbr. Suspend→Addr 13 Delete→Addr 15 Recover→Addr 17

How to start / stop using cards? Example: Start using cards, which card ID from 12345: 00001 to 12345: 00100,

totally 100 cards in sequence. Step1: Entering Function Mode Step2: Recover -> Addr. (Order no. 17) Step3: Input Start Addr. -> 00001 Step4: Input End Addr.-> 00100 Succeed!

6.2 Access Mode Under Mode 6, with different Arming PWD and Duress Code, users have different access mode as below.

Arming PWD = ０

Arming PWD ≠０

Duress Code =０

Duress Code ≠０ Mode 6

Access Mode Card only Card and Arming PWD

Duress Code not workable

Duress Code only

14

7. Quick Guide (Function Menu) Under Function Menu, you could just press the indicative nbr. to get into concerning set-up screen directly.

Function Nbr. Function Nbr. Add→Card ID 11 Alarm Relay Tm 36 Add→RF – learn 12 Arming Delay Tm 37 Suspend→Addr 13 Arming PWD 38 Suspend→ID # 14 Arming Pulse 39 Delete→Addr 15 Delete→ID # 16 Auto Relock 41 Recover→Addr 17 Egress (R.T.E.) 42 Recover→ID # 18 Attendance 43 Antipass Group 19 Master Node 44 Force Open.. 45 Password 21 Close & Stop 46 Access Mode 22 Anti-pass back 47 Extend Options 23 Duress Code 48 Single Floor 24 Multi Floors 25 Language (English) 511 Master Code 52 Master Range 53 Terminal Port 54 AR721R32 Node 55 Node ID 31 Open Time Zone 56 Auto Open Zone 32 Information 57 Door Relay Tm 33 Clock Setting 58 Door Close Tm 34 Control Mode 59 Alarm Relay Tm 35 View Events 50

15

8. Function description 24 Single Floor To setup user for single floor access

(This function is only workable under the situation that AR-727H combined with AR-401RO16 and Control Mode is not Mode 6.)

25 Multi Floors To setup user for multi floors access (This function is only workable under the situation that

AR-727H combined with AR-401RO16 and Control Mode is not Mode 6.)

For example: User 0001 access to floor 17, 22, 31, 32 (Supposed no basement)

1. Entering “Function Menu” 2. Press 25 3. Enter user address: 00001 4. Select range: 2 (for 17 – 32)

1: 01 –16 2: 17 – 32 5. 0 -> stop 1 -> Yes

1000010000000011 31 Node ID To setup Node ID (default: 001), range from 001 to 254 33 Door Relay Tm To setup how long the time will be that door close after a card

flashing. Range: 0 ~ 600 (sec.) To set value “0” will make door keep opening, after 2nd card flashing, then door close. (Default value: 7 sec.)

34 Door Close Tm Extended time for door opening time. (Default value: 15 sec.)

35 Alarm Relay Tm When abnormal condition arisen, how long the alarm will take place. Range: 0 ~ 600 (sec.) To set value “0” will make alarm relay keep on until disarming, then alarm relay off. (Default value: 7 sec.)

36 Alarm Delay Tm The time between setting Alarm on and its real starting working time. (Default value: 1 sec.)

37 Arming Delay Tm The time between setting Arming on and its real starting working time. Range: 0 ~ 600 (sec.) (Default value: 1 sec.)

39 Arming Pulse Range: 0 ~ 2500 (sec.) TTT = 000: Latch (Toggle)

(Default value: 1 sec.) 56 Open Time Zone Set door open / close automatically. Details:

1. Enter “Function Menu” 2. Setup opening time first, Function no. 56 3. Auto Open Zone, Function no. 32

1: Yes 2: No

16

Drawing explanation: 1. Time schedule for Door Relay, Wait Delay (Door Close Tm),

Alarm Delay, Alarm Relay

Door Close Tm

Alarm Delay

Alarm Relay

Door Relay

K

2.

Arm Tim

Tim

SigArm

SigArm

ArmSig

Seq

Flashing card O

Arming Delay, Arming on

Arming Delay

Arming Relay

Flashing card OK

If abnormal conditions arisen, will cause Alarm E.g. Door open too long (over allowed time) Force open

Vi l i i b k l i

ing Delay Timing

ing 1 Sequence-

Arming Delay Timeing 1

Check Point AArming is set

nal Outputing

nal Outputing

If TTT = 000Level Triggle

ingnal Output

If TTT = 200Pulse Trigger

Pulse TriggerIf TTT = 050

0.5 Second

2.0 Seconds

uence

17

After arming is set, the system enters TTiimmiinngg 11 SSeeqquueennccee. Right on CChheecckk PPooiinntt AA, the system is in arming situation and enters Arming Mode, if door is close, the system engages the Timing 2 Sequences, if door is open, it will wait until the door is closed to engage the Timing 2 Sequences. Timing 2 Sequences-

Door opened by not using “Forced Open”: In arming situation, the system enters TTiimmiinngg 22 SSeeqquueenncceess once the door is opened by not using “Forced Open”. During TTiimmee PPeerriioodd BB, the system is back to arming situation if door closed, if door is still open right on CChheecckk PPooiinntt CC, alarm is activated after TTiimmee PPeerriioodd DD. User can disarm the system in TTiimmee PPeerriioodd DD to avoid the alarm generated, or disarm the system in TTiimmee PPeerriioodd EE to turn off the alarm which is activating. Door opened by using “Forced Open” and if “Forced Open” feature, Command 28, is disabled:

Timing 2Sequences

Alarm TimeAlarm Delay Time

Check Point C

Arming Idle TimeDoor Unlock Time

Door is opened

Time Period B Time Period D Time Period E

In arming situation, the system enters AAllaarrmm DDeellaayy TTiimmee right away once using “Forced Open” opens the door and if “Forced Open” feature is disabled. The alarm is activated after TTiimmee PPeerriioodd DD. User can disarm the system in TTiimmee PPeerriioodd DD to avoid the alarm generated, or disarm the system in TTiimmee PPeerriioodd EE to turn off the alarm which is activating. Door opened by using “Forced Open” and if “Forced Open” feature, Command 28, is enabled: In arming situation, the alarm is generated and system enters AAllaarrmm TTiimmee right away once using “Forced Open” opens the door and if “Forced Open” feature is enabled. User can disarm the system in TTiimmee PPeerriioodd EE to turn off the alarm that is activating. Signal Output Arming or Disarming Signal Output- RED WHITE, CN2 Once arming is set, after Arming Delay Time period, the system generates a Level Trigger if TTT=000, and a Pulse Trigger if TTT>000 and the time period of the Pulse Trigger is based on the calculation 0.01xTTT second(s). For TTT=000, entering the Edit Mode or disarming the system will reset the Level Trigger. For TTT>000, entering the Edit Mode every time or disarming the system will generate a Pulse Trigger.

18

Arming Delay TimeTiming 1Sequences

In Arming ModeArming is set

Signal OutputArming

Signal OutputArming

If TTT = 000Level Triggle

ArmingSignal Output

If TTT = 200Pulse Trigger

Pulse TriggerIf TTT = 050

0.5 Second

2.0 Seconds

Disarmingor

Edit ModeEnter

Edit ModeEnter

Arming Switch Setting Signal Output- ORANGE WHITE, CN2 Once Arming switch is pressed, a Level Trigger is generated until Arming switch is released to reset this signal.

Card Present Signal Output- Brown, CN2 Any identifiable tag in the RF field, it will output a low level signal; a Level Trigger is generated until a tag is absent to reset this signal.

9. Special Design 9.1 AR-727H connected with 2 pcs of AR-661U long-range reader (Set one

AR-661U being Exit reader and the other one being Entry reader) to apply to Anti-pass back.

Identifiable tag Absent

Identifiable tag Present

Card Present Signal Output

Release uttonfor disarming

Press button forSet Arming

Arming Switch Output

CPU version must be at least 3.2 or up. In stand-alone system, without connecting to any controller, AR-727H could

integrate with 2 pcs of AR-661U to apply to anti-pass back. ◎ No special setting up necessary for AR-727H. ◎ Set one AR-661U with wiegand 34 bit format output and the other one with

38 bit. (Please refer to manual of AR-661U to have details.) ◎ Set card to have anti-pass back checking.

(Order no. 19) This special design is especially suitable for car parking control. The special design is only workable with AR-661U, not available with AR-721U,

AR-721K. (wiegand reader) Soyal Product AR-829E (CPU version at least 5.6) 、AR-721H4 (CPU version at

least 3.1V) also have this special design. The original function that AR-727H connecting with one wiegand reader

(AR-661U, AR-721U, AR-721K) to apply to Anti-pass back is still available.

19

9.2 How AR-727 connects with a weigand reader (AR-721K, AR-721U, AR-661U) and to apply to anti-pass back?

(1) Main manu (2) Input command:47，

enable antipass—1:YES 2:NO，input1； in or out –1:in 2: out，input default value(1 or 2 ).

attention：if AR-727H would be in door and then the weigan reader would be out door.

9.3 How to set multi AR-727H connects with a net controller and to apply to anti-pass back?

Both card and reader have to apply to anti-pass back. 1.card setting:

step1:701 Client step2:user card edit step3:mark anti-pass back.

. 2. reader setting (AR-727H): step1:main manu step2:command 47 step3: enable antipass—1:YES 2:NO，input1；

in or out –1:in 2: out，input default value(1 or 2 ).

9.4 How to setting the weigand reader (AR-721U, AR-721K, AR-661U) and AR-727H at the same net controller to apply to the anti-pass back?

Both card and reader have to apply to anti-pass back Card setting: step1:701 Client

step2:user card edit step3:mark anti-pass back. Hardware setting: weigand reader (AR-721U, AR-721K): Set controller WG port as in or out if WG port is port 1 then would be in door and port 2 would be out door.

Port 1 (Channel 17)

Port 2 (Channel 1

20

AR-716Ei PCB

8)

Software setting: 701 Server. Step1: 701E Parameter Step2: door number Step3:mark [Door Number 17]or [Door Number 18]

AR-727H setting: (1) main manu (2) command 47

enable anti-pass back 1:YES 2:NO，input1； in or out –1:in 2: out，input default value(1 or 2)

Attention: if weigand reader would be in door then AR-727H would be our door. 9.5 How to set that user arrive single floor or multi-floor?

Either way to set user arrive single floor or multi-floor function. 1. Set by keypad for standalone installation (AR-727H+AR-829L485+AR-401RO16) Set user arrive single floor


Step2: User Setting (command 2) Step3: Single Floor (command 4) Step4: Enter user address and set to access which one floor. Set user arrive multi-floor


Step2: User Setting (command 2) Step3: Single Floor (command 5) Step4: Please refer to “function description” to get detailed

explanation. 2. Set by software for networking installation

(PC+AR-801CM+AR-716EV2+AR-727H+AR-829L485+ AR-401RO16)

21

Go to 701 Client \ User card edit \ User Access Floor Edit Select User. Select controller and reader node that manages that elevator. Select the card user can access which floor. Click “Write to Controller”.

9.6 How to set AR-401RO16 parameter?

(ex. Card Release Tm) Step1: * + 1 2 3 4 5 6 + # enter the “FUNCTION MENU” Step2: Tools (command 5)

Step3: AR-721R32 Node (command 5) Step4: Input NodeID, Card Release Tm and P.B Release

Tm (Default value: 7 sec.) Note: 1. AR-401RO16 has no push button input function, but you still enter push button input second in order to complete this command. Otherwise, this command will be failed. 2. They are one-way transmission is between AR-727H and AR-401RO16, so you will find that you change Card Release Tm from 7 sec. to 10 sec. But the parameter will be stay default value 7 sec. Don’t worry about this matter. Actually, it is already changeable.

22

10. Installation 10.1 Steps: 1. Use the screwdriver to screw the mounting plate on the wall. 2. Pull cable ends through the access hole in the mounting plate.

Connect plug 7 pins to socket CN1 Connect plug 4 pins to socket CN2 Connect plug 8 pins to socket CN3 Connect plug 3 pins to socket CN5

3. Attach AR-727H to the mounting plate and install screw (supplied) into the hole at the bottom with the Allen wrench (supplied).

4. Apply power. Green LED [POWER] will light up, a beep sound and LCD panel message will show up.

10.21. T

aAo

2. Tadb

3. E4. A

sRiw

5. Psrp

Installation Notice: he distance between AR-727H and its auxiliary reader should be more than 50 cm nd less than 12 meter. (Suggested value) R-727H could be fixed inside the secure area as an exit and its auxiliary reader utside as an entrance reader, but not directly behind AR-727H. he reading range of AR-727H will be up to15 cm. However, when AR-727H or its uxiliary reader is mounted directly on a metal surface, the reading distance ecreases slightly. To reduce this effect, we suggest inserting a wood or plastic etween the mounting surface and the unit. xit Switch input must be a dry contact, without voltage present. R-727H does not supply power to operate electric strike or magnetic locks, a eparated power supply are required. efer to strike or magnetic lock manufactures instructions, if common power supply

s used for both AR-727H and electronic door lock; make sure to install the diode, hich is provided with AR-727H. ower supply should be at least 9 VDC to max. 24 VDC and at least 3W. DC power hould be clean and filtered with no more than 0.3 VAC ripple (Peak to Peak). Do not un AC power in the same cable with DC power to AR-727H. While it is always referable to use a separate power supply for AR-727H and strike.

23

6. Run the following cables to the AR-727H location. Conduit is recommended to reduce the effects of EMI/RFI and for physical protection of the wires.

Cable Types and Distances Wire Application Cable Type Description From Power Supply 2-cond, 18-22 AWG n/a From Locking Device and power supply or gate operator

2-cond. See Mfr’s Specifications

n/a

From external alarm system’s Door Monitor Switch (for shunting)

2-cond, 18-22 AWG 100 m

From Exit Button 2-cond, 18-22 AWG 100 m From Optional Auxiliary Reader 2-cond unshielded 22 AWG,

plus a separate 4-cond, shielded 22-24 AWG cable

50 cm - 12 m

7. Hardware connecting distance suggestion as follows:

a. RS-232: The distance between PC and converter (AR-801CM) can not be more than 2 meters

b. RS-485: The distance between converter (AR-801CM) and the farthest controller (or reader) can not be more than 300 meters. c. Wiegand: The distance between RS-485 reader (or controller) and Wiegand reader can not be more than within 3 to 5 meters.

d. Do not run AC power in the same pipe with communication wire (See drawing 2). It should be separate installation (See drawing 1).

(Drawing 1)

Separate installation Reader Lock

LockIn the same pipe

Reader

(Drawing 2)

24

8. We suggest that the customer use ”Shield Twisted Pair” and avoid Star wiring for good communication when installation. a. We suggest using the following cable in RS-485 communication.

b. Please use the following installation method, it is correct.

c. Don’t use the following installation method, it will cause communication error.

801CM ORController

Controlle ORReade

rvr

801CM ORController

Controller ORReader

xx

v

25

11. Wiring

Table 1 - Connector CN3 Color Coding Wire Application Wire Color Description

1 Blue White (N.O.)DC24V1Amp Door Relay 2 Purple White (N.C.)DC24V1Amp Door/Alarm Relay 3 White (COM)DC24V1Amp Door Sensor 4 Orange Negative Trigger Input Exit Switch 5 Purple Negative Trigger Input Alarm Relay 6 Gray N.O. / N.C. Optional

7 Thick Red DC Power 12V Power 8 Thick Black DC Power 0V

Table 2 - Connector CN1 Color Coding Wire Application Wire Color Description

1 Thick Green RS-485(B-) Networking 2 Thick Blue RS-485(A+) 3 Thin Blue Wiegand DAT:1 Input

ABA Clock Input Wiegand 4 Thin Green Wiegand DAT:0 Input ABA Data Input

Buzzer 5 Pink Buzzer Output 5V/100mA, Low 6 Brown LED Green Output 5V/20mA, MaxLED 7 Yellow LED Red Output 5V/20mA, Max

Table 3 - Connector CN5 Color Coding

Wire Application Wire Color Description 1 Red N.C. 2 Orange COM Tamper Switch 3 Yellow N.O.

Table 4 - Connector CN2 Color Coding

Function Wire Color Description Arming Setting Switch 1 Orange

White Latch type

Serial Port 2 Yellow White

Serial output (Transisto(4800,N,8,1)

Arming LED 3 Red White Arming output (Active low)

Card Present 4 Brown White

Card present output active (Transit output)

COM

NO

NC

JP1 Alarm Relay

Door Relay K1

K2

26

OFF
ON
r open collector)

low

Purple White

Blue White

Gray

White

12. Installation diagram 12.1 Magnetic lock

NO.

COM.- G

ND

+12VDC

The installation of 727H and magnetic lock

Whi

te(

CO

M. )

Lock

( -G

ND

)P

urpl

e W

hite

( N

.C. )

-GN

D

Power Supply12VDC 2A

Pur

ple

Bla

ck(

- GN

D )

Red

( +

12V

DC

)

DOOR EXITPush Button

CN

3


Lock(+12VDC )+12VDC

Magnetic Lock

CN3

AR-727H

CN5

CN1

CN

2

27

12.2 Electric bolt lock

- GND

- GND

+12VDC

NO.

COM.

12VDC 2APower Supply

The installation of 727H and electric bolt lock

Push ButtonDOOR EXIT

Pur

ple

Bla

ck(

- GN

D )

Red

( +

12V

DC

)

CN

3

Blu

e W

hite

( N

O. )

Whi

te(

CO

M. )

Lock( -GND )

Lock(+12VDC )12VDC 2APower Supply Electric Bolt Lock

CN5

AR-727H

CN

2

CN3CN1

+12VDC

28

12.3 Electric strike

+12VDC- GND

NO.

COM.

The installation of 727H and electric strike


DOOR EXITPush Button P

urpl

e

Bla

ck(

- GN

D )

Red

( +

12V

DC

)

Blu

e W

hite

( N

O. )

Whi

te(

CO

M. ) C

N3

Lock(+12VDC )+12VDC12VDC 2APower Supply

Electric Strike

Lock

( -G

ND

)

-GN

D

AR-727H

CN5

CN3CN1

CN

2

29

12.4 Magnetic door contacts and alarm system

- GN

D

+12

VD

C

ALM

.

N.C

.

CO

M.

N.O

.

+12

VD

C

- GND+12VDC

The installation of 727H, magnetic door contacts and alarm system

Alarm System


Bla

ck(

- GN

D )

Red

( +

12V

DC

)

Gray( ALM. )

Red

( +

12V

DC

)

Bla

ck(

- GN

D )

Mag

netic

Doo

r C

onta

cts(

CO

M. )

CN

3

Ora

nge(

Doo

r S

enso

r )

Mag

netic

Doo

r C

onta

cts ( NC

. )


Magnetic doorcontacts

CN1

CN5

AR-727H

CN

2

CN3

30

12.5 Wiegand reader

Green

Blue

Yellow

PurpleBrown

The

inst

alla

tion

of 7

27H

and

aux

iliar

y re

ader

s

721U

12V

DC

2A

Pow

er S

uppl

y

Red

(+12

VD

C)

Bla

ck

Red

1

721K

Red

Black

CN

1

1

~

Yel

low

Bro

wn

CN

2G

reen

Pin

k

Blu

e

661U

Bla

ck(-

GN

D)

Bro

wn

Yel

low

Gre

en

Pin

k Blu

e

727H

CN

3

CN

1

31

AR

-737

U

Bla

ck

Pow

er S

uppl

y12

VD

C 2

A

The

inst

alla

tion

of 7

27H

and

aux

iliar

y re

ader

s 73

7U

Red

Purple

Blue

Green

BrownYellow

AR-727H

Yel

low

Bla

ck(-

GN

D)

Red

(+12

VD

C)

1

CN

3

Gre

en

Bro

wn

Pin

k

Blu

eC

N1

32

12.6 Networking installation 12.6.1 two set of AR-716EV2 parallel installation

ToN

ode:

009

Nod

e: 0

16

ToN

ode:

008

Nod

e: 0

01

Not

e:1.

The

conn

ectin

g di

sanc

e be

twee

n th

e 80

1cm

and

you

r pc

can

not

be

mor

e th

an 2

m.

AR

-727

H

AR

-727

HA

R-7

27H

Green

Blue

Blue

Green

Green

Blue

Green

Blue

CN

1

CN

1C

N1

conn

ect t

o P

C

15V

DC

2A

Pow

er S

uppl

y

Con

trol

ler

Nex

t

Red

Bla

ck

Blue

BlackGreen

Red

AR

-727

H a

nd A

R-7

16E

/727

E n

ewor

king

inst

alla

tion

AR

-716

E

o

r

AR

-727

E

CN

1C

N3

CN

3C

N1

CN

5

CN2

~~

CN

1

~~

CN

1C

N3

CN

5

CN2

CH

1

JP2

JP1

HO

ST

CN

3C

H2

CN

2

BV

+

Vin

Vin

GN

DB

V-

727i

CN2

AR

-727

H

CN

5

CN

3C

N1

CN2

CN

5

~~~~

JP1

JP2

Vin

Vin

BV

+B

V-

CN

2

CN

1 CN

3

CH

1

HO

ST

CH

2

727i

AR

-716

E

o

r

AR

-727

E

GN

D

CN

1

33

12.6.2 AR-716EV2, AR-829E and AR-727H parallel installation

727i

CN

3 Red

JP1

JP2

Bla

ck

CH

2

HO

ST

CN

2C

N1

CN

2

AR

-727

H, A

R-8

29E

and

716

EV

2 ne

twor

king

inst

alla

tion

CN

2

Green

Blue

AR

-829

EA

R-7

27H

線紅

線黑

GN

D

VinCN

1V

in BV-

BV+

綠線線藍

~~

CH

1

Pow

er s

uppl

y15

VD

C 2

A

CN2

CN

1

CN

5

CN

3

AR

-727

H

Blue

Green

至

Nod

e: 0

09

Nod

e: 0

16

CN

1

CN

3C

N1

CN

5

CN

1

Green

Blue

CN

3

CN

5

CN

1

CN

1

Green

Blue

CN2

AR

-727

H

CN2

Nex

t Con

trolle

r

~~

AR

-716

EV2

or

AR

-727

Ei

Min

imum

2 m

eter

conn

ect t

o P

C

34

12.7 Lift controller AR-401RO16 installation

Pow

er S

uppl

y12

VD

C 2

.4A

Dia

gram

of A

R-7

27H

and

AR

-401

RO

16

Bla

ck

Yel

low

-+

CN

CN

1

CN

CN

3

Red

Red

+

- +

Bla

ck

DC 12V

Gre

en

Blu

e

--+

+-

+-

35

12.8 AR-727H & AR-801CM & PC installation

The installation of 727H, 801CM and PC


Push ButtonDOOR EXIT

COM.

NO.

Red

( +1

2VD

C )

Bla

ck (

- GN

D )

Pur

ple

Whi

te (

CO

M. )

Blu

e W

hite

( N

O. )

12VDC 2APower SupplyElectric Bolt Lock

Lock ( -GND )

Lock (+12VDC ) +12VDC

- GND

CN3

AR-801CM

CN

2CN1

CN3CN1

CN5

Blue

Green


AR-727H

Gre

en

Minimum 2 meterconnect to PC

To PC

Blu

e

Black

Red

36

12.9 RS-232 Printer 12.9.1 Printer setting - Baud rate: 4800, N, 8, 1 12.9.2 Hardware installation 1

1D0000000 Tm

The Wiring of 727H and printer (SH24)

TP1 DATA4K7

V12

GND

Serial Port (2nd Pin of CN2)

Yellow White

AR-727H

4K7

BGND

E

B

C

EC

C1815TX

DB25 male

Replace Circuit (Distance between AR-727H & SH24 Printer <1M)

Suggest Circuit

MAX232A

TX

Black (8th Pin of CN3)Pin GND7

Pin RX (in)2

SH24Printer

2.9.3 Hardware serial port format – select “printer format” Step1: * + 1 2 3 4 5 6 + #

enter the “FUNCTION MENU” Step2: Tools (command 5)

Step3: Terminal Port (command 4) Step4: 1: AR401RO16 2: LED 3: PRN 4: Duress Current Data: 1 Please enter 3, let serial port become printer format.

2.9.4 Print result ate Week Time Card ID Status 5/03/2004 MON 20:24:16 0000000248 Power On Ver 3.5 5/03/2004 MON 20:24:18 02: Reader Off Line 5/03/2004 MON 20:24:22 0000000250 Clear Message!! 5/03/2004 MON 20:25:01 01: Set Clock! 5/03/2004 MON 20:25:30 01:00001 Card Access OK 5/03/2004 MON 20:26:20 01: Egress! 5/03/2004 MON 20:35:23 01:00001 Card Access OK

he above data is printer when someone flash card, Egress, power on/off, clear essage and set clock. But note that the data will be not printed from invalid card.

37

13. Software Application 13.1 Configuration PC + AR-801CM + AR-727HV3 13.2 The difference between AR-727H and AR-727HV3 AR-727HV3 CPU: Version 5.1 UP / Hardware: 24LC256 13.3 Software Version Support 701 Server Ver 6.22 & 701 Client Ver 6.28 13.4 Software function via PC 1. Eleven sets of Time Zone (set via Time Zone Edit)

a. From Time zone 1 to Time zone 11 b. Support to linkable for each zone. c. Support the holiday if enable

2. Up to 120 holidays that can be set in a year starting from the editing date. (set via Holiday Edit)

3. Different time zone for each user (set via User Card Edit) 4. Which code will show in daily transaction record? Code Status Code Status M11 Normal Access M03 Invalid M16 Door open via Egress Button M17 Alarming M04 Time Zone error M30 Anti-pass-back error M01 PIN code error 5. Time and Attendance function 6. Work status of LCD display of the reader when standalone

View Message when standalone, it will show work status on left top corner if it is normal access (See Also: historical records page 10). Other will show code.

7. Auto-show work status (set via Time Zone Edit) a. Time zone 00 (Default), range from Sunday to Saturday. b. Work status 00:00 – 00:00 stand for fixed Duty on in work status 23:59 – 23:59 stand for fixed Duty off in work status 00:01 – 00:01 stand for retain last status that user press in work status XX:XX – YY:YY stand for as follows: For example, 09:00-18:00 Work status will show Duty on before 9 o’clock, show Duty off between 9 o’clock and 18 o’clock and show Overtime Off after 18 o’clock.

38

14. Troubleshooting

Questions Answer No appearance 1. Check power, if it is 9 – 24 VDC adaptor?

2. Check if the polarity is correct?

Can not connect to PC 1. Check if Transmission LED light up? (Green / Red) 2. Check 701 Server, if set-up is correct?

Please refer to 701 Server manual for details. 3. If connecting to PC via AR-801CM converter, check if the

power (Green) light up?

How to find out Card ID with a user address?

1. Entering “Function Menu” 2. Press 11 3. Entering “user address”

How many Cards exist in system?

1. Entering “Function Menu” 2. Press 57

15. Return of Products Please contact the distributor who sold the unit. All service and repairs must be done through an authorized distributor. 16. Warranty SOYAL warrants that the product(s) shall be free from manufacturing defects in materials and workmanship for a period of twelve (12) months from the date of delivery provided that the product was properly installed and used. The foregoing warranty shall not apply to defects resulting from abuse, misuse, accident, unauthorized alteration or repair, neglect, acts of God (such as floods, fire, etc.). SOYAL shall, at its option, either repair or replace product(s) which prove to be defective within the warranty period. SOYAL will replace any product found to be defective within the first three months of purchase provided said product was properly installed and used. Distributor agrees to insure the product or assume the risk of loss or damage in transit to prepay shipping charges and to use the original shipping container or equivalent. Customers shall seek assistance from the distributor who sold you product(s). Repaired or replaced product(s) are warranted for ninety (90) days from the date of repair or replacement, or for the remainder of the original product’s warranty period, whichever is longer.

Note: Don’t tear a paster such as S/N: 727H Warranty B-0307-000107 on the PCB board, it is SOYAL warranty.

39

17. Transponder Record Table Be sure to record the user number, the user name, the card ID number (site code: card code), and the user code and keep this information in a secure place. A black user log form has been included for purpose. Do not write on this form; use it as a photocopy master.

User Add. User Name Site code: Card code PIN code

Programmed by: Date:

Company Name:

Company Address:

City:

Other Information:

40

18. Specification

Power Supply 10 – 24 VDC

Power Consumption <3W (250 mA @ 12VDC)

RF Frequency 125 KHz

Reading range 10 – 18 cm

User Interface 16 metallic texture keypads、beep、128*64 dot LCD panel and 8 LED indicator.

Networking RS – 485, 9600,N,8,1

External reader port Suitable for all WG、ABA reader； 125K、13.56M (Mifare) or 2.4G reader

Door Relay 2A / 12V N.O. / N.C. / COM 0.1 ~ 600 sec. / Latch type

Alarm Relay 2A / 12V N.O. / N.C. / Jumper selectable 0 ~ 600 sec.

DI input Egress button ／Door sensor／Arming switch

Transistor output Arming ／Duress ／Card sensor

Tamper switch Limit Switch（N.O. N.C. COM.）

Serial Port Supported for AR-721R32、LED display、 Relay board、Printer etc.（4800,N,8,1）

Material ABS

Dimensions(mm) 127 (L) * 91 (W) * 46 (H)

Net Weight 250 gram

41

727hv3 mu en

Documents