7870.pdf
TRANSCRIPT
8/16/2019 7870.pdf
http://slidepdf.com/reader/full/7870pdf 1/3
ZD-916 Soldering Station1. Description
ZD-916 Soldering Station designed for lead free soldering especially.
Heating up from the room temperature to 350 in 30 seconds.℃
This tool is used in the fields of electronic research, teaching and production, especially in the
repairing and soldering on the electronic appliances and communication equipments.
1.1 ontrol !nit
"he soldering iron tool is controlled automatically #y the micro-processor. "he digital control
electronics and high-$uality sensor and heat e%change system guarantee precise temperature
control at the soldering tip. "he highest degree of temperature precision and optimal dynamic
thermal #eha&ior under load conditions is o#tained #y the $uic' and accurate recording of the
measured &alues in a closed control circuit( and this design is especially for the lead-free
production technics.
1.) Soldering *ron +ZD-,15
ZD-,15 soldering iron ith a poer of 60/(Heat up rating 130/)and a ide spectrum
of soldering tips(" series)can #e used anyhere in the electronics field.
"he high poer and slim design ma'es this iron suita#le for fine soldering or'. "he
heating element is made of " and the sensor on the soldering tip can control the soldering
temperature $uic'ly and accurately.
). "echnical Specification
ode oltage supply
29-1611 110130
29-161) ))0),0
Spare parts4
ode oltage oer odel ame
22-,157 ), 60/ ZD-,15 Soldering *ron
"echnical data4
Supply
&oltage
Soldering *ron
oltage
oer "emperature 8unction display
110-130 7
))0-),0 7
), 60/
+Heat up rating 130/
160 -,20℃ ℃ D display
3. :perating *nstruction
3.1 lace the soldering iron in the holder separately. "hen connect the plug to the receptacle
on the station and turn cloc'ise to tighten the plug nut. hec' that the poer supply is
corresponding to the specification on the type plate and the poer sitch is on the ;:88<
position. onnect the control unit to the poer supply and sitch on the poer. "hen a self-
test is carried out in hich all display elements are sitched on #riefly. "he electronic system
8/16/2019 7870.pdf
http://slidepdf.com/reader/full/7870pdf 2/3
then sitches on automatically to the set temperature and displays this &alue.
3.) "he display and temperature setting
"he digital display4
shos the actual temperature of the soldering tip .①
shos the setting temperature. ressing the ;!< or ;D:/< #utton can sitch the②
digital display to the set point display. "he set-point can #e changed for ±1℃ #y tapping the
;!< or ;D:/< #utton. ressing the #utton ill change the set-point $uic'ly. "he digital
display ill return automatically to the actual &alue and the iron ill reach to the setting
temperature $uic'ly.
= display4 Sitching the temperature display from to #y pressing the ; =③℃℉ ℃ ℉ ℃
<#utton and then the electronic system ill display the actual temperature and setting℉ ①
temperature in ( and &ice &ersa.② ℉
/hen the actual temperature on the soldering tip is less than the set-point( ;H>7" :<④
ill display and ma'e the soldering tip heating up.
/hen the a#solute offset is more than ?10 #eteen the actual temperature and the set-⑤ ℃
point on the soldering tip or the no@@le( ;/7*"< ill display. *t means that the temperature
electronic control system is not in the sta#le situation( e should ait a moment to let the
;/7*"< disappear.
/hen ;>AA:A< display( there may #e a trou#le on the system( or the soldering iron is⑥
not connected to the control system correctly.
,. Safety *nstruction
"he manufacturer assumes no lia#ility for uses other than those descri#ed in the
operating instructions or for unauthori@ed alterations.
"he operating instructions and cautions should #e read carefully and 'ept in an easily
&isi#le location in the &icinity of the control system. on-o#ser&ance of the cautions ill
result in accidents( inBury or ris's to health.
5. aution!
5.1 "he poer cord only can #e inserted in appro&ed poer soc'ets or adapters.
5.) High "emperature
"he temperature of the soldering tip ill reach as high as around ,00℃(C5)℉) hen the
8/16/2019 7870.pdf
http://slidepdf.com/reader/full/7870pdf 3/3
poer sitch is on. Since mishandling may lead to #urn and fire( #e sure to comply ith the
folloing precautions4
Do not touch metallic parts near the soldering tip= no@@le.
Do not use this system near the flamma#le items.
7d&ise other people in the or' area that the unit can reach a &ery high temperature
and should #e considered potentially dangerous.
"urn off the poer sitch hile ta'ing #rea's and hen finishing using.
efore replacing parts or storing the system( turn off the poer and let it cool don
to the room temperature.
5.3 ta'e care of your soldering station
Do not use this tool for any applications other than soldering or desoldering.
Do not rap the iron against the or' #ench or otherise su#Bect the iron to se&ere shoc's.
Do not file the soldering tip to remo&e the o%ide( please ipe the tip on the cleaning sponge.
!se only accessories or attachments hich are listed in the operation manual. !se of other
tools and other accessories can lead to a danger of inBury.
lease turn off the poer #efore connecting or disconnecting the soldering iron.
5., aintenance
efore further use( safety de&ices or slightly damaged parts must #e carefully
chec'ed for error-free and intended operation. *nspect mo&ing parts for error-free
operation and that they donEt #ind( or hether any parts are damaged. Damaged
safety de&ices and parts must #e repaired or replaced #y a $ualified technician( so
long as nothing else is indicated in the operation manual. !se only accessories or
attachments hich are listed in the operation manual. !se of other tools and other accessories
can lead to a danger of inBury.
5.5 Feep children at a distance
Do not allo other persons to touch or distur# the soldering tool or poer cord. Feep other
persons aay from the or' area. !nused soldering tools should #e stored in a dry location
hich is out of the reach of children. Sitch off all unused soldering tools.
5.6 rotect yourself against electrical shoc's
7&oid touching grounded parts ith your #ody( e.g. pipes( heating radiators and so on. "he
grip of antistatic designed soldering tool is conducti&e.
5.C /or' en&ironment
Do not use the soldering tool in a moist or et en&ironment. "he soldering iron should #e
placed on the holder after finished using.
5.2 :#ser&e the &alid safety regulations at your or' place.