8 1sa8a-paint work

8/10/2019 8 1SA8A-Paint Work

1/19


2/19

SA8-PAINTING WORK/2

texture and meets the warrantee terms stated. Such proposals shall be submitted as an option in the

Tender submission and will be considered during the assessment of tenders.

External plaster surfaces Warrantee term : five (5) years

2 coats of external mastic, 1 coat of masonry primer, 2 coats of acrylic emulsion

Internal plaster surfaces Warrantee term : two (2) years

2 coats of internal mastic, 1 coat of masonry primer, 2 coats of PVA emulsionInternal ferrous metalwork Warrantee term : two (2) years

1 coat of red oxide primer, 2 coats of gloss enamel

d. External ferrous metalwork Warrantee term : five (5) years

1 coat zinc phosphate primer, 2 coats of gloss enamel

e. Internal woodwork painted Warrantee term : two (2) years

2-3 coats of wood primer, 2 coats of enamel

f. Exposed uPVC pipes and fittings Warrantee term : three (3) years

1 coat of solvent-based primer, 2 coats of acrylic emulsion (as in a.)

8.5 MATERIALS

8.5.1 Materials Generally

Approved manufacturers and brand names

All materials used in the Works shall be only those of the manufacturers and brand names previously

approved by Engineer, and shall be clearly marked with the manufacturers name or trademark and a

description of the contents and colour. Any painting materials other than those approved for the Works shall

be immediately removed from the Site. All materials shall be mixed and applied strictly in accordance with

the manufacturers specified, printed instructions, using only one of the methods recommended by the

manufacturer.

Mixing paint brands or types

The practice of mixing different types of paints, or mixing or substituting paints of the same type from

different manufacturers is prohibited. Should this practice occur, Engineer, at its sole discretion, may

immediately issue a Site Instruction to stop all painting works and permanently remove from the site, any

person or persons he deems to be culpable.

Thinning paints

Thinning of paint materials is generally not necessary, and may only be performed after written approval by

Engineer. In those cases, approval will only be granted on condition that thinning is limited to the thinning

material recommended by the manufacturer, and according to the method of application (usually limited to

spray-painting). In no case will thinning of the paint material exceed 10% by volume of the paint. Where

Radcote mineral silicate paint is specified, it is strictly forbidden to change the contents in the containers in

any way

Tinting and colouring paints

All tinting or colour mixing, generally, shall be performed only at the manufacturers premises, and no

tinting or colouring may be done at the site without Engineers approval

8.5.2 Material types

External mastic

Where specified in this section, External mastic means a pre-mixed and packaged material of cement-lime

mortar in powder form, containing additives which make it suitable for bonding to external masonry

surfaces, including concrete, brick, and plaster. Any external mastic product that is packaged in liquid

form, and/or requires the addition of cement, may not be used without the prior written approval of

Engineer.

Internal mastic

Where specified in this section, Internal mastic means a pre-mixed and packaged material of cement-lime

mortar in powder form, containing additives which make it suitable for bonding to internal masonry

surfaces, including concrete, brick, and plaster. Any internal mastic product that is packaged in liquid

form, and/or requires the addition of cement, may not be used without the prior written approval ofEngineer.


3/19

SA8-PAINTING WORK/3

Masonry primer

Where specified in this section, Masonry primer means a material containing acrylic-based emulsion

binders, and incorporating mineral extenders in the pigment that make it suitable as an external sealant.

The material is water soluble, and suitable for application over both external and internal mastic substrates.

Acrylic Emulsion paint

Where specified in this section, Acrylic Emulsion Paint means a paint using an acrylic copolymer emulsionbinder, which is soluble in water and suitable as a finishing paint for external masonry surfaces.

PVA Emulsion paint

Where specified in this section, PVA Emulsion Paint means a paint using PVA copolymer emulsion binders,

which is soluble in water and suitable as a finishing paint for internal masonry surfaces.

Red oxide primer

Where specified in this section, Red oxide primer means an alkyd-based, lead-free, ferrous oxide primer,

soluble in white spirit, and suitable as a rust inhibitor to steel and other ferrous and zinc based metals,

particularly for internal use.

Zinc phosphate primer

Where specified in this section, Zinc phosphate primer means an alkyd-based primer using zinc phosphate

pigments, soluble in white spirit, and suitable as a rust inhibitor to steel and other ferrous and zinc based

metals, for both internal and external use.

Cold galvanizing paint

Where specified in this section, Cold galvanizing paint means an alkyd-based primer using zinc-rich

pigments, soluble in white spirit, and suitable as a rust inhibitor to steel and other ferrous and zinc based

metals, for both internal and external use. Also suitable as a touch-up primer to hot galvanized materials

that have lost their protection due to welding, grinding, cutting, etc.

Hot-dipped galvanizing

Where specified in this section, Hot-dipped galvanizing means the process of static electroplating molten

zinc-rich material to bare steel or other ferrous products to produce enhanced anti-corrosion protection to

the substrate.

Non-ferrous metal primer

Where specified in this section, Non-ferrous metal primer means an alkyd based primer using zincchromate pigments, soluble in white spirit, and suitable as a primer to aluminium, copper, brass, and zinc

based metals, for both internal and external use.

Wood primer

Where specified in this section, Wood primer means a priming paint with oleo-resinous binders, soluble in

white spirit, and suitable to prime both hardwoods and softwoods, including those that are highly resinous.

It contains leafing aluminium pigments, and is suitable to receive alkyd type finishing paints.

Enamel paint

Where specified in this section, Enamel paint means an alkyd or glyptal synthetic resin-bound paint, used

as a finishing coat especially for wood or metal materials. The finish may be in high-gloss, semi-gloss or

satin.

8.6 PREPARATION FOR PAINTING

8.6.1 General

The Contractor shall observe the manufacturers written instructions (either in the technical data-sheets or

on the container label) regarding preparation requirements, which may include, but not be limited to

cleanliness, dryness, & stability of the surface.

8.6.2 Internal and external plastered surfaces

Before the application of mastic coats, notify Engineer of intention to start work, and confirm whether

plastering works have been approved. Inspect each section of plastering work and report any defects such

as cracks, hollowness, or uneven surfaces to Engineer, and receive instruction prior to commencing the

putty coats. Repair minor defects as directed. Where plaster cracks are required to be raked out and filled,

use an approved proprietary brand non-shrinking gypsum filler. Brush down the plaster surfaces to remove

dust and loose sand. Begin application of mastic only when the plaster is dry.


4/19

SA8-PAINTING WORK/4

8.6.3 Woodwork

All exposed woodwork shall be prepared for painting in the fabrication workshop before delivery to the site.

All nails shall be punched and stopped and wood surfaces cleaned free of grease, wax, dirt and other poorly

adhering materials before further preparation.

Wood surfaces to be painted shall be knotted, stopped, rubbed-down with abrasive paper, and primed.

Further stopping, rubbing-down and priming cycles may be necessary to achieve the required finish.Use an approved wood primer as specified in clause 8.4.2

Use a proprietary brand hard stopping to fill nail holes, open joints, splits on the surface. Linseed oil putty

may only be used internally to Engineers approval.

Scrape all knots and resin pockets then apply two coats of patent knotting, made of shellac dissolved in

naphtha or methylated spirits.

Wood surfaces to be oiled or varnished shall be knotted, stopped, rubbed-down with abrasive paper, and

varnished. Further stopping, rubbing-down and varnishing cycles may be necessary to achieve the required

finish.

Use a proprietary brand cellulose wood filler for stopping

Use an approved internal or external wood varnish as specified in clause 8.4.2

Woodwork as prepared above will be inspected on delivery to the site. Finishing coats for painted wood and

final coat for varnished wood will be completed on site.

8.6.4 Steel and ferrous metals

All structural steelwork and metalwork shall be prepared for painting at the place of fabrication before being

delivered to the site. Complete all fabrication work including welding, drilling, bolting, cutting and then grind

or sandblast these parts to a suitable surface.

Remove oil and grease from all exposed surfaces by wiping with an approved solvent

Remove loose mill scale and rust by chipping, scraping, or wire brushing. If the preparation is not approved

by Engineer, treat the surfaces with an approved rust remover.

Surfaces to receive cold galvanizing paint shall be ground or sandblasted.

Notify Engineer for inspection after the surfaces have been prepared, before any coating is applied.

Apply one coat of primer as specified in clause 8.4 before delivery to the site.

8.6.5 Fair-faced concrete (off-form)

For concrete surfaces to be painted with emulsion paint or enamel paints, carefully chip off any grout

projections, differences in level, fill up crevices, and level the surfaces generally with an approved

proprietary pure gypsum non shrinking filler.

8.5.6 Radcote mineral silicate paint

For external plastered surfaces to be painted with Radcote mineral silicate paint, the finished plaster render

shall be inspected before the application of any paint. To ensure evenness of texture, any holes or cracks to

be raked out and filled, shall be filled with the same grade of mortar as the original surface, and allowed to

dry for 21 days. All work shall be continuous over the full surface between construction joints. Block down

the surface with an emery stone of suitable abrasiveness to get an even texture. Brush down with a wire

brush to remove surface bumpiness, then brush down with a soft bristle brush to remove dust and powder.

8.7 DELIVERY, HANDLING & STORAGE

All materials shall be delivered to the Site in the manufacturers containers with seals unbroken, and shall

be kept in a locked store on the Site until issued for use. The store shall be constructed so as to minimize

extremes of temperature, and access to the store shall be made available for Engineers inspection at all

times.

8.8 APPLICATION PROCESS

8.8.1 Labour

All painters shall be skilled and experienced in their trade. The Contractor shall submit a list of the names of

all painters to Engineer for approval, and issue each painter with a photograph ID name tag, which must be


5/19

SA8-PAINTING WORK/5

worn at all times while working at the Site. Unskilled labourers are not permitted to do the work of skilled

labourers

8.8.2 Tools & equipment

All brushes, rollers, spray equipment, tools, pots, etc., used in executing the Works shall be kept clean and

free from foreign matter, and shall be thoroughly cleaned prior to being used with a different type of

material. Solvents to be used for the cleaning of equipment shall follow the manufacturers

recommendations.

All paint materials shall be applied with approved quality bristle brushes, rollers, compressed-air or airless

spraying at the Contractors discretion, but in conformity with the manufacturers recommended methods of

application. Distemper brushes are to be of an approved type not less than 150mm wide. The use of rags,

cotton waste, or any other material or method that is not recommended by the manufacturer for applying

the paint, will not be permitted.

8.8.3 Environmental conditions for work

No external or internal painting work shall be carried out in wet or foggy weather, or in extremes of

temperature or humidity, or on surfaces that are not thoroughly dry. No painting work shall be carried out in

conditions of airborne dust. The Contractor shall take all necessary measures to protect completed coats

from rain and dust in the vicinity of the works. Engineer will not consider any claim for extension of time for

adverse environmental conditions where the Contractor has not taken steps to protect the painting work

against these conditions.

Primed or undercoated woodwork and metal work shall not be left in an exposed or unsuitable condition for

an undue period before completing the painting process. If this situation occurs, causing a degradation of

the properties of the exposed materials, Engineer, at its discretion, will issue a Site Instruction to remove

the damaged material and re-apply that coat, at the Contractors expense.

8.8.4 Preparation of materials

All paint materials shall be thoroughly stirred and mixed when the manufacturers containers are opened

and the contents are transferred to painters pots. Where necessary, the paint materials shall be strained to

remove all skin, lumps and the like before being used. During the progress of painting works, materials held

in painters pots shall not be left unsealed in the event of temporary stoppage of work.

8.8.5 Sequence of work

No mastic (putty coat) or priming coat shall be applied until the substrate surface has been inspected and

the preparatory work has approved by Engineer. No subsequent undercoats or finishing coats shall be

applied until the previous coat has been similarly inspected and approved. To control this sequence of work,

including inspections and approval by Engineer, the Contractor shall submit a checklist control sheet for

approval and coordination with Engineer Supervisors.

No consecutive coats of paint shall be the same shade of colour (except white). The manufacturer will

supply information on alternative shades, on request, and any tinting in this respect shall be undertaken at

the manufacturers premises prior to sealing the containers.

Each coat of the work shall be thoroughly dry before subsequent coats are applied. At the completion of

each coat, the work shall be rubbed-down with abrasive paper appropriate to the nature of the material.

8.8.6 Protection and cleaning

During execution of the painting works, the Contractor shall be responsible for the protection of all other

finishing works from paint drops, splashes, roller marks or over-spray. These include electrical and lighting

fittings, sanitary fixtures and fittings, all other unpainted or decorative surfaces, metal trims, glass, joinery,

furniture and the like.

Ladders, scaffolds, and jump-ups used during the execution of painting works, shall ensure the protection of

the finishing materials against scratching, scuffing, marking and other damage.

Damage to other finishing work caused by a) and b) above shall be repaired as the work progresses, using

solvents appropriate to the paint and the finishing material.

Stains, scratches, scuff marks or any other damage to other finishing materials caused by painting or

inappropriate use of solvents will become the responsibility of the Contractor, who will repair or replace the

items at his own expense, at the discretion and instruction of Engineer.


6/19

SA8-PAINTING WORK/6

Upon completion of sections of painting works, and prior to the final inspection by Engineer, all defects

caused by painting works shall be made good and thoroughly cleaned.

8.9 FINAL INSPECTION AND HAND-OVER

Where each section of painting works has been agreed to be handed over , the Contractor shall, at the time

of the joint inspection, submit to Engineer the following documents, certificates, and records of the Workscompleted;

Certificates of quality of goods from each manufacturer

Joint warrantee for each of the systems specified

Copy of materials delivery inspection records

Copy of in-progress inspection records for preparation, priming and finishing coats

Copy of non-conformances and approved corrective action

Engineer will supply the Contractor with one sample set of the above documents for reference, upon

request.

8.10 PAINT TYPE

Apply ICI paint as follows or approved equivalent.

(A) EMULSION FOR EXTERNAL USE PAINT SYSTEMS

MASTIC : ICI Cemputty (KG) ( A 502 29130 )

PRIMER : Dulux Weathershield sealer ( A369_75230)

TOP COAT

System 1 : High Quality Paints _ Warranty period: 5 years

Dulux Weathershield Plus ( A 915 - Line )

System 2 : Economic & Low Price _ Warranty period : 2.5 years

Super Maxilite Exterior ( A 919 Line)

(B) EMULSION INTERNAL USE PAINT SYSTEMS

MASTIC : ICI Cemputty (KG) ( A 502 - 29130 )

PRIMER : Dulux Interior Primer ( A 934 - 75007)

TOP COAT

System 1 : High Quality Paint _ Warranty period : 5 years

Maximum washable & high hair-line cracks.

Dulux Easy Clean ( A990_ Line)

System 2 : Long Lasting & Economic paints _ Quaranty period : 2.5 years

High coverage

Super Maxilite Interior ( A 901 - Line)

(C) ALKYD PAINTS ( for wood & metal surfaces )

PRIMER : Maxilite anti-corrosive red primer ( A 526 - 74001 )

TOP COAT

Satin Finish

Dulux Satin ( A 369 - Line )

OR

High Gloss

Maxilite Enamel ( A 360 - Line )


7/19

SA8-PAINTING WORK/7

PRODUCTNAME ICI CEMPUTTY

Product Code A502 29130

COLOUR RANGE White

PACK SIZE 40 kg

USAGE ICI Cemputty is a treatment material for touching up gaps, pin holes and

patching-up of uneven concrete or plastering surface before applying

finishing coats or before using wallpaper etc. to achieve a level surface.

The product is designed for both interior and exterior use.

AREA OF APPLICATION Concrete, mortar, plaster, precast concrete, hard and soft boards, etc

CHARACTERISTICS One-pack type for easy handling.

Maximum adhesion to the substrate and cohesion strength

Low water absorption, a good water-repellent effect and good water

proofness.

Hair-line crack resistance and impact resistance.

Forms a hard surface after curing without any shrinkage cracks.

Strengthens weak surfaces of concrete, prevents poor adhensiveness and

discoloration of finish coats.Improves weather and alkali resistance for finish coats

VOLUME SOLIDS 100%

DRYING TIMES Single coat at standard thickness.

Surface Dry 2 hours at 300C.

Recoat 4 hours after the first coat.

Hard Dry 1 day at 300C

THEORETICAL COVERAGE 1 1,2 m2/ Kg.

APPLICATION Steel or plastic trowel to achieve high effectiveness

MIXING INSTRUCTION

Mixing Ratio 1 part of water to 3 parts of material by weight.

Let water into tin first, then pouring the powder slowly. Use a mixer if

available or adequate mixing equipment to mix until having homogenous

paste which is then ready for use.

SURFACE PREPARATION Surface must be dry and clean from dirt, dust, oil, grease and foreign

matters. All large cracks on the surface of wall or ceiling must be filled

with cement or Watson Putty (55-D200) prior to application. No need to

wet the surfaces before coating.

Pot life Around 3 hours

Shelf life Up to 6 months if store in tightly sealed container.

SAFETY, HEALTH AND

ENVIRONMENTAL

INFORMATION

Irritating to respiratory system and skin.

Risk of serious damage to eyes.

Contains: CEMENT WITH > 2PPM CHROMIUM VI. May produce an allergic

reaction.

Keep out of the reach of children.

Avoid contact with eyes.

In case of contact with eyes, rinse immediately with plenty of water and

seek medical advice.

Wear eye/ face protection.

If swallowed seek medical advice immediately and show this container or

label.

PRODUCT NAME Dulux Weathershield Alkaline Resistance Sealer

Product Code A936-75230

PACK SIZE 5 litres & 18 litresUSAGE Dulux Weathershield Alkaline Resistance Sealer is 100% acrylic emulsion


8/19

SA8-PAINTING WORK/8

sealer providing excellent alkaline resistance, enhance water repellence,

paint film adhesion and long lasting colour for topcoat.

COLOUR RANGE White only

FILM PROPERTY

Water Resistance Reinforcing WATER PROOFING performance for finished coats and protect

wall from harsh weather effect.COMPOSITION Acrylic resin, lightfast non-lead pigments, mineral extenders and water.

VOLUME SOLIDS Minimum 38%

DRYING TIMES Single coat at standard thickness 100 Micron

Touch Dry 15-30 minutes dependent on temperature and humidity.

Recoat 1-2 hours.

THEORETICAL COVERAGE Coverage under normal conditions is 10-12m2/ litre (with dry paint film

thickness is 30 micron)

APPLICATION Brush, roller, conventional spray.

Add up to 1 part of clean water to 20 parts of paint (20%).

SPRAY RECOMMENDATIONS

Conventional Spray Satisfactory through most equipment.

CLEANING UP Clean all equipment with clean water immediately after use.

SURFACE PREPARATION Surfaces must be sound, clean, free from all defective or poorly adhering

material such as powder, grease or wax

The relative humidity is under 16% according to Protometer or let the

substrate from 21 to 28 days in normal conditions (average temp.

30deg.C, humidity of environment about 80%).

SYSTEM INFORMATION

Powdery Surfaces

Alkali and New Surfaces

Sealer (1 coat)

Dulux Solventborne Sealer

(A579-15054)

Dulux Weathershield Alkaline

resistance Sealer 2000

(A936-75230)

Finish (2 coats)

Dulux Weathershield

(A915 Line)

Or

Dulux Weathershield High

Sheen

(A918-line)

Or

Dulux Weathershield Water

Resistance (A954-line)

SAFETY, HEALTH AND

ENVIRONMENTAL

INFORMATION

No added lead and mercury.

Avoid contact with skin.

Harmful to aquatic organisms, may cause long-term adverse affects in

the aquatic environment.

Keep out of reach of children.

Do not breathe vapour/spray.

Wear suitable gloves.

Use only in well ventilated areas.

Avoid release to the environment.

PRODUCT NAME Dulux Weathershield Exterior Emulsion

Product Code A915-Line

PACK SIZE 1L, 5L & 18L

USAGE Dulux Weathershield is a high quality, 100% acrylic based emulsion

paint for new or previously painted exterior masonry surfaces such as

brickwork, plaster, cement, rendering, and semi-permanent exterior

finishes. It is specially formulated to provide at least 6 years protection


9/19

SA8-PAINTING WORK/9

against fungus and algae growth.

Dulux Weathershield is alkali resistant, has excellent durability as well

as colour fastness. It is specially formulated with water-proofing

properties against wind-driven rain when applied on exterior walls.

COLOUR RANGE See appropriate Dulux Weathershield Plus Exterior Wall Finish Colour

CardFILM PROPERTY

Chemical Resistance

Water Resistance

Resistant to mild atmospheric fume attack and to the salts in new

mortar, rendering and similar surfaces.

Resistant to the levels of atmospheric humidity normally experienced in

exterior environments.

COMPOSITION (nominal) Pigment: Lightfast Non-Lead Pigments.

Binder : Acrylic Emulsion

Solvent : Water

VOLUME SOLIDS 40% (nominal), other colours will vary.

DRYING TIMES Single coat at standard thickness:

Surface Dry Dependent on temperature and humidity

Recoat 1 2 hours.

THEORATICAL COVERAGE On smooth surfaces of average porosity 13m2/litre/coat.


THINNING

Brush or Roller Ready for use.

Conventional Spray Add up to 1 part clean water to 10 parts of paint (10%)




SURFACE PREPARATION Ensure the surface to be painted is clean, dry, the relative humidity is

under 16% according to Protimeter or let the substrate from 21 to 28

days in normal conditions (average temp. 30deg.C, humidity ofenvironment is about 80%). Remove all loose paint or powdery residue

by brushing/scrapping with a stiff fibber brush under running water or

with a high pressure water jet.

Treat area affected by mould, lichen, algae or moss with Dulux

Fungicidal Wash (A980-19260). Repair minor defects with a suitable

exterior grade filler. Seal with one coat of Dulux Platinum Sealer (A931-

18177P) to achieve best performance, preventing alkali attack. Areas

that remain powdery, friable of chalky after cleaning should be sealed

with a coat of Dulux Solventborne Sealer (A579-15054) for better

adhesion.

Notes: Do not apply Dulux Weathershield in wet weather (the

temperature of surface should not be under 100C).

SYSTEM INFORMATION

Powdery Surfaces


Primer (1 coat)


(A579-15054)

Dulux Platinum Sealer

(A931 18177P)

Or Dulux Sealer 2000

(A931-18177)

Finish (2 coats)

Dulux Weathershield

(A915-Line)

SAFETY, HEALTH AND

ENVIRONMENTAL INFORMATION




10/19

SA8-PAINTING WORK/10






Use only in well ventilated areas.Avoid release to the environment.

Contains: BIOCIDE

PRODUCT NAME Super Maxilite Exterior Emulsion Paint


PACK SIZE 4L and 18L

USAGE Super Maxilite Exterior Emulsion Paint is a high quality, matt finish,

providing an effective protection to level exterior masonry surfaces,

either new or previously painted, such as brickwork, plaster, cement,

etc The product, with longer lasting colours, is specially formulated to

prevent fungus / algae growth and provide better alkaline resistance.

Super Maxilite Exterior Emulsion is specially water-proofing properties

against wind-driven rain when applied on exterior walls.

COLOUR RANGE See appropriate Colour Card

FILM PROPERTY

Chemical Resistance

Water Resistance

Resistant to mild atmospheric fume attack and to the salts in new

mortar, rendering and similar surfaces.

Resistant to the levels of atmospheric humidity normally experienced in

exterior environments.


Binder : Styrene Acrylic Emulsion

Solvent : Water

VOLUME SOLIDS White 37.5% (nominal), other colours will vary.DRYING TIMES Single coat at standard thickness:

Surface Dry Dependent on temperature and humidity

Recoat 1 2 hours.

THEORATICAL COVERAGE Theoretical coverage which can be achieved under normal conditions is

12.5m2/litre at 30 microns.

APPLICATION Brush, roller, or conventional spray

THINNING

Brush or Roller Ready for use. If required add up to 1 part of clean water to 10 parts of

paint (10%)



SURFACE PREPARATION Remove all loose or defective paint or powdery residues by thorough

brushing and scraping, using a fibre brush. Allow new surfaces to dry out

completely.

Treat any areas affected by mould, lichens, algae and moss with Dulux

Fungicidal Wash (A980-19260).

Make good minor defects with a suitable exterior grade filler. Use a sand

and cement mix for larger holes and cracks. Allow to dry.

If surfaces that remain powdery, friable or chalky after thorough

preparation should be sealed with a coat of any appropriate Dulux sealer

(see below).

Note: Do not apply Super Maxilite Exterior Emulsion Paint during wet

weather. It is advisable to apply paint under normal exterior weather.


11/19


SYSTEM INFORMATION

Powdery Surfaces


Primer (1 coat)


(A579-15054)

Dulux Platinum Sealer(A931-18177P)

Or Dulux Sealer 2000

(A931-18177)

Finish (2 coats)

Super Maxilite Exterior Emulsion

Paint (A919-Line)

SAFETY, HEALTH AND

ENVIRONMENTAL

INFORMATION

Keep container tightly closed and keep out of reach of children.

A suitable cartridge mask should also be worn when rubbing down.

Ensure good ventilation during application and drying.

Do not breathe vapour/spray. In case of insufficient ventilation during

spraying wear suitable respiratory equipment.

All respiratory equipment must meet an appropriate approved standard.

Keep away from food, drink and animal feeding stuffs.

When applying paints it is advisable to wear suitable eye protection.



Remove splashes from skin: use soap and water or a recognised skin

cleaner.

Care must be taken when transporting paint. Keep container in a secure

upright position.

Contains no added lead or mercury.

Protect from extremes of temperature. Store in a cool place.

In the event of an accident contain and collect spillage using sand or

earth. Do not empty into drains or water courses.

Dispose of any paint waste in accordance with the appropriate

Environmental Quality Regulations.

PRODUCT NAME Dulux Interior Primer


PACK SIZE 5 & 18 litres

USAGE Dulux Interior Primer is a premium waterborne acrylic wall primer, used

for interior masonry surfaces such as: brickwork, plaster and cement,

etc Especially, Dulux Interior Primer enhances the perfect smooth finish

wall, good adhesion and long lasting colour of top coat.

COLOUR RANGE Light blue white

FILM PROPERTYWater Resistance Can tolerate the level of atmospheric humidity present in normal interior

environment.

COMPOSITION (nominal) Acrylic resin, mineral extenders and water.

VOLUME SOLIDS Minimum 40%.

DRYING TIMES Single coat at standard thickness 100 Micron.

Touch Dry 30 minutes dependent on temperature and humidity.

Number of coat 1 coat

THEORETICAL COVERAGE Theoretical coverage is 10-12m2/ litre.


THINNING

Brush or Roller Add up to 15-20% of clean water


12/19


Conventional Spray Add up to 15-20% of clean water



CLEANING UP Clean all equipments with clean water immediately after use.

SURFACE PREPARATION Surface to be painted must be sound, clean, and as dry as possible and

free from all defective or poorly adhering material, dirt, grease or wax.

Remove all mildew, fungus, dirt or powdery residue by

scrubbing/scraping with stift fibre brush under running water. Treat

areas affected by mould, lichen, algae or moss with Dulux Fungicidal

Wash

Note: Paints will not adhere on dirty and powdery substrate which are

not thoroughly cleaned

SYSTEM INFORMATION Primer (1 coat)

Dulux Interior Primer

(A934 - 75007)

Finish (2 coats)

Dulux Supreme 3-in-1

(A900 Line)

OrDulux Pentalite (A921 Line)

Or

Maxilite Interior (A901 Line)

SAFETY, HEALTH AND

ENVIRONMENTAL

INFORMATION


Keep out of reach of children

Do not breathe vapour/spray



PRODUCT NAME Dulux Easy Clean


PACK SIZE 5 litres

USAGE Dulux Easy Clean as the ultimate interior emulsion that delivers a blend

of performance. It offers luxurious & always keep the wall dirty-free as

new wall with 3 key attributes:

Stain resistance better than other normal paints

Stain removal easy without any paint film impact

10 times better to remove stain than other normal paints.

COLOUR RANGE See appropriate Colour Card

FILM PROPERTIES

Water Resistance Resistant to the levels of atmospheric humidity normally experienced in

interior environments.

COMPOSITION (nominal) Pigment: Lightfast Non-Lead Pigments and Mineral Extenders.

Binder : Acrylic Emulsion

Solvent : Water

VOLUME SOLIDS White 41% (nominal), other colours will vary.

DRYING TIMES Single coat at standard thickness.

Surface Dry 30 minutes

Recoat 2 3 hours.


12 - 14m

2

/ litre on smooth surfaces of average porosity at 30 micronsdry film thickness.


13/19


APPLICATION Brush, roller , conventional spray.

THINNING

Brush or Roller For normal use thinning is not usually necessary, but if required up to 1

part of clean water to 20 parts of paint (5%).


SPRAY RECOMMENDATIONSConventional Spray Satisfactory through most equipment.


SURFACE PREPARATION Ensure the surface to be painted is clean, dry, the relative humidity is

under 16% according to Protimeter or let the substrate from 21 to 28

days in normal conditions (average temp. 30deg.C, humidity of

environment is about 80%). Remove all loose paint or powdery residue

by brushing/scrapping with a stiff fibber brush under running water or

with a high pressure water jet.

Treat area affected by mould, lichen, algae or moss with Dulux Fungicidal

Wash (A980-19260). Repair minor defects with a suitable exterior grade

filler. Seal with one coat of Dulux Interior Primer (A934-75007) to

achieve best performance, preventing alkali attack. Areas that remain

powdery, friable of chalky after cleaning should be sealed with a coat of

Dulux Solventborne Sealer (A579-15054) for better adhesion.

SYSTEM INFORMATION

Powdery Surfaces


Primer (1 coat)


(A579-15054)

Dulux Interior Primer

(A934 75007)

Finish (2 coats)

Dulux Easy Clean

(A990 - line)

SAFETY, HEALTH AND

ENVIRONMENTAL

INFORMATION









Avoid release to the environment.

Contains: BIOCIDE

PRODUCT NAME Super Maxilite Interior Emulsion


PACK SIZE 4 and 18 litres

USAGE Super Maxilite Interior Emulsion is a good quality, high coverage, and

durable emulsion with a smooth matt finish. It is suitable for all normal

interior masonry surfaces including brickwork, plaster, cement, as well

as hard and soft wallboards.

COLOUR RANGE See appropriate Super Maxilite Interior Colour Card

FILM PROPERTIES

Water Resistance Will tolerate the levels of atmospheric humidity present in normal

interior environments and will withstand moderate washing.


Binder : Acrylic Copolymer Emulsion


14/19


Solvent : Water

VOLUME SOLIDS 30% (nominal), other colours will vary.

DRYING TIMES Single coat at standard thickness

Touch Dry Dependent on temperature & humidity

Recoat 1 2 hours

THEORATICAL COVERAGE Theoretical coverage which can be achieved under normal conditions is 9 10m2/litre on smooth surface of average porosity at 30 microns

thickness.

APPLICATION

THINNING

Brush, Roller, Conventional Spray

Brush or Roller For normal use thinning is not usually necessary. If required up to 1 part

clean water to 10 parts of paint (10%)





SURFACE PREPARATION Surfaces must be sound, clean, dry and free from all defective or poorly

adhering material, dirt, grease, wax and be rubbed down using a

suitable abrasive paper and dusted off.

Treat any areas affected by fungi or algae with Dulux Fungicidal Wash

(A980-19260).

If surface remain powdery or suffer from alkali attack after thorough

preparation seal with one coat of an appropriate primer (see below).

SYSTEM INFORMATION

Powdery Surfaces

Alkaline and New Surfaces

Primer (1 coat)

Dulux Solvnetborne Sealer

(A579-15054)

Dulux Platinum Sealer (A931-18177P)

Dulux Sealer 2000(A931-18177)

Finish (2 coats)

Super Maxilite

Emulsion

(A901-Line)

SAFETY, HEALTH AND

ENVIRONMENTAL

INFORMATION

Keep container tightly closed and keep out of reach of children.

A suitable cartridge mask should be worn when rubbing down.

Ensure good ventilation during application and drying.

Do not breathe vapour/spray. In case of insufficient ventilation during

spraying wear suitable respiratory equipment.

All respiratory equipment must meet an appropriate approved standard.

When applying paints it is advisable to wear eye protection.



Remove splashes from skin: use soap and water or a recognised skin

cleanser.

Care must be taken when transporting paint. Keep container in a secure

upright position.

Contains no added lead or mercury.

Protect from extremes of temperature. Store in a cool place.

In the event of an accident contain and collect spillage using sand or

earth.

Do not empty into drains or water courses.

Dispose of any paint waste in accordance with the appropriate

Environment Quality Regulations.

PRODUCT NAME Maxilite Anti-Corrosive Red Primer



15/19


PACK SIZE 0.8L, 3L, 18L

USAGE Maxilite Anti-Corrosive Red Primer is an alkyd resin based with excellent

rust preventive primer for interior and exterior metalwork such as steel

frames or any type of mild steel substrates, etc

COLOUR RANGE Reddish brown.

COMPOSITION (nominal) Pigment: Red Oxide and Mineral Extenders.Binder : Alkyd

Solvent : White spirit

VOLUME SOLIDS 30%

DRYING TIMES At 300C and 79.5% relative humidity.

Surface Dry 45 minutes

Recoat 1 hour 45 minutes

FILM THICKNESS

THEORETICAL COVERAGE

Wet : 60 - 70 micro-metres.

Dry : 30 - 35 micro-metres.

Theoretical coverage which can be achieved under normal conditions is

11.7m2/litre at 30 microns dry film thickness.

APPLICATION Brush, roller or conventional spray.

THINNING

Brush or Roller Add maximum 1 part of Dulux Thinner 850-41 or gasoline or white spirit

to 20 parts of paints (5%).

Conventional Spray Add maximum 1 part of Dulux Thinner 850-41 or gasoline or white spirit

to 10 parts of paints (10%).



CLEANING UP Clean all equipment with gasoline or ICI Thinner 850-41 or white spirit

immediately after use.

SURFACE PREPARATION Steel surfaces should be manually prepared by power or hand tool to

BS7079 part A1 1989 ST3.

SYSTEM INFORMATION

Metal

(Ferrous)

Primer (1 coat)

Maxilite Anti-corrosive

Red Primer (A526-

74001)

Undercoat (1 coat)Optional

Dulux Speed Undercoat

(A545-101)

Finish (2coats)

Maxilite

Enamel Paint

(A360-Line)

Or Dulux

Gloss Finish

(A365-Line)

FLASH POINT 35OC

SAFETY, HEALTH AND

ENVIRONMENTAL INFORMATION

FLAMMABLE

Repeated exposure may cause skin dryness or cracking.



Keep container tightly closed.

Keep away from sources of ignition no smoking.




After contact with skin, wash immediately with plenty of water and

soap.

Do not empty into drains.


Not recommended for interior use on large surface areas.


16/19


If swallowed, seek medical advice immediately and show this container

or label.

PRODUCT NAME Dulux Satin Finish


PACK SIZE 0.8L & 3L

USAGE Dulux Satin Finish is a high-quality satin enamel paint for wood and

metal surfaces. It offers a luxurious and modern beauty by:

Smooth surfaces

Satin paint film.

Besides, with high coverage & fast drying factors, Dulux Satin Finish is

an effective protection coat for wood & metal goods.

COLOUR RANGE Reference Dulux Satin Finish Colour Card.

FILM PROPERTIES

Chemical Resistance Resistant to mild chemical fume attack but where there is heavy attack,

e.g. actual contact with chemicals, specialist paint systems will be

required.

Heat Resistance Generally resistant to heat up to 90oC but some discoloration of light

colours may occur at temperatures above 80oC.

Water Resistance Resistant to the levels of atmospheric humidity present in normal interior

and exterior environments and will withstand repeated washing. Not

suitable for use on immersed surfaces.

COMPOSITION (nominal) Alkyd resin, lightfast non-lead pigment, solvent thinner, non-contained

Benzene and Methanol, non-lead dryer.



Touch Dry 1 2 hours

Recoat 6 12 hours

FILM THICKNESSES Wet:100micro-metres

Dry: 45 micro-metres


12 14m2/litre

APPLICATION Brush, Roller, Conventional Spray.

THINNING

Brush or Roller Add up to 1 1,5 part of Dulux Thinner 850-41 or gasoline to 10 parts

of paint (10% to 15% by volume).

Conventional Spray Add up to 1 1,5 part of Dulux Thinner 850-41 or gasoline to 10 parts

of paint (10% - 15% by volume).

Note No add to other enamel paints. Stirring well before use.


Conventional Spray Can apply all conventional sprays.

CLEANING UP Clean all equipment with Dulux Thinner 850-41 or gasoline immediately

after use.

SURFACE PREPARATION Surfaces must be clean, dry and free from all defective or poorly

adhering material, dirt, grease, wax etc. Previously painted surfaces

should be thoroughly rubbed down using a suitable abrasive paper and

then dusted off.

For optimum performance new galvanised and aluminium surfaces

should be cleaned and degreased, then pre-treated with an appropriate


17/19


pre-treatment primer to ensure good adhesion.

SYSTEM INFORMATION

Wood

Normal Metal

Primer (1 coat)

Dulux Aluminium Wood Primer

Sealer (A519-3697)

Maxilite Anti-corrosive RedPrimer (A526-74001)

Or Dulux Grey Green Zinc

Phosphate Primer (A500-388)

Undercoat (1 coat)

Optional

Dulux Speed

Undercoat

(A545-101)

Finish (2

coats)

Dulux

Satin

Finish

(A369-

Line)

Metal-plated Dulux Galvprime Grey

(A931-10420)

SAFETY, HEALTH AND

ENVIRONMENTAL

INFORMATION

Flammable

Keep away from combustible material.

In case of fire use foam, dry powder, AFFF, CO2- Never use water.

Toxic to aquatic organisms, may cause long-term adverse effects in the

aquatic environment.

Do not empty into drains.


If breathing in, it causes sleepy or dizzy.


Repeated exposure may cause skin dryness or cracking

Contains: Ethyl Methyl Ketoxime. May produce an allergic reaction



label.

Use only in well ventilated areas.Avoid release to the environment. Refer to special instructions/ Safety

data.

PRODUCT NAME Maxilite Enamel


PACK SIZE 0.45L, 0.8L, 3L & 18L

USAGE Maxilite Enamel paint from ICI is a high alkyd paint. It is produced

under ICIs advanced technology and it offers a perfect surface for metal

and wood with:

Gloss pain film

Smooth surfaceOther preeminent factors are wide range of colors, quick drying, easy

application and no added lead and mercury.

COLOUR RANGE Reference Maxilite Enamel Colour Card

FILM PROPERTIES

Chemical Resistance Resistant to mild chemical fume attack but where there is heavy attack,

e.g. actual contact with chemicals, specialist paint systems will be

required.

Heat Resistance Generally resistant to heat up to 90oC but some discoloration of light

colours may occur at temperatures above 80oC.

Water Resistance Resistant to the levels of atmospheric humidity present in normal interior

and exterior environments and will withstand repeated washing. Notsuitable for use on immersed surfaces.


18/19



Binder:Alkyd

Solvent : White Spirit



Touch Dry 1-2 hoursHard dry After 12 hours

FILM THICKNESSES Wet:55micro-metres

Dry: 30 micro-metres


13 14m2/litre

APPLICATION Brush, Roller, Conventional Spray

THINNING

Brush or Roller Add up to 1 part of Dulux Thinner 850-41 or gasoline to 10 parts of paint

(10%).

Conventional Spray Add up to 1 part of Dulux Thinner 850-41 or gasoline to 7 parts of paint

(15%).Note No add to other enamel paints.



CLEANING UP Clean all equipment with gasoline or Dulux Thinner immediately after

use.

SURFACE PREPARATION Surfaces must be clean, dry and free from all defective or poorly

adhering material, dirt, grease, wax etc. Previously painted surfaces

should be thoroughly rubbed down using a suitable abrasive paper and

then dusted off.

For optimum performance new galvanised and aluminium surfaces

should be cleaned and degreased, then pre-treated with an appropriate

pre-treatment primer to ensure good adhesion.

SYSTEM INFORMATION

Wood

Metal

Primer (1 coat)

Dulux Aluminium Wood

Primer Sealer (A519-3697)

Maxilite Anti-corrosive Red

Primer (A526-74001)

Or Dulux Grey Green Zinc

Phosphate Primer (A500-

388)

Undercoat (1 coat)

Optional

Dulux Speed Undercoat

(A545-101)

Finish (2

coats)

Maxilite

Enamel

Paint(A360-

Line)

Metal Dulux Galvprime Grey

(A931-10420)


19/19


SAFETY, HEALTH AND

ENVIRONMENTAL

INFORMATION

Flammable

Keep away from combustible material.

In case of fire use foam, dry powder, AFFF, CO2- Never use water.

Toxic to aquatic organisms, may cause long-term adverse effects in the

aquatic environment.

Do not empty into drainsDo not breathe vapour/spray.


Repeated exposure may cause skin dryness or cracking

Contains: Ethyl Methyl Ketoxime, Cobalt Carboxylate. May produce an

allergic reaction



label.


Avoid release to the environment. Refer to special instructions/ Safety

data.

Refer to Maxilite Enamel paints Datasheet for further details.

8 1sa8a-paint work

Documents