8/10mm sliding door and side panel...8/10mm sliding door and side panel refer to sheet 15 for...
TRANSCRIPT
8/10mm SLIDING DOOR AND SIDE PANELRefer To Sheet 15 For Relevant Product Codes
VictoriaPlum.com0344 804 48 48
C hange the hand by turning moving panel inside out & top rail upside down.
This product is universal, not handed
BEFORE YOU START, HERE IS SOME IMPORTANT INFORMATION
1) General Information
2) Additional Notes
Please inspect this product upon delivery, any missing parts or manufacturing
defects must be reported immediately to the supplier. Damage or defects reported
later will not be accepted. TAKE CARE WHEN HANDLING GLASS PARTS - AVOID
HEAVY CONTACT BETWEEN THE GLASS EDGES AND ANY HARD SURFACE.
Glass breakage claims will not be accepted after the product has been unpacked.
Please note: Aluminium is a soft metal, and undergoes a series of extrusion,
fabrication, polishing and anodising processes in order to create your finished
shower enclosure. Some light surface marks are normal, and is a result of the
manufacturing processes. Quality control has ensured that this item is of a good
standard, and is fit for purpose.
Please read these instructions carefully before starting installation.Special care should be taken when drilling walls to avoid hidden pipes or electrical cables.
Note: this product is heavy and may require two people to install.
This product is heavy and may require two people to install.
TOOLS REQUIRED
Ø3mm Drill bit
Ø6mm Drill bit
Pencil
Spirit level
Tape measure
DESCRIPTION DESCRIPTIONPART IMAGE PART IMAGE
Drill
Flat-headScrewdriver
Cross headScrewdriver
Mallet
Silicone Sealant
PZ1
1
3
THESE DIMENSIONS ASSUME THE WALLS ARE PLUMB AND THE SHOWER TRAY IS LEVEL, AND THAT THE WALLS ARE TILED DOWN TO THE TOP OF THE TRAY USING A 10mm TILE/WET WALL PANEL.
ASSEMBLY INSTRUCTIONSIf you require help, we advise you to contact a competent plumber
FITTED SLIDING DOOR AND SIDE PANEL DRAWING
Installation Steps
101200/1400/1600/1700
10
10
1 01 0
10
80
0/9
00
1010
10
1010
22
ASSEMBLY INSTRUCTIONS - DRAWING
(10)
(8)
(7)
(5)(4)(3)
(2)
(1)
(6)
(9)
(11)
(12)
(13)
(14) (15) (16) (17) (18)
(31)
(19) (20) (21) (23)
(25)
(26)
(28)
(29)
(30)
(33)(34)(35)(36)(37)(38)(32)
(24)
(1) 1x Guide Rail Seal(2) 1x Door Stop Cap(3) 1x Cover Cap (Guide Rail)(4) 1x Wall Post Cover Cap A(5) 1x Guide Rail(6) 10x Wall Plugs (7) 10x Screws 4x30(8) 1x Wall Profile A(9) 1x Wedge Gasket Seal(10) 1x Fixed Panel(11) 1x Fixed Panel Seal(12) 1x Handle B (10mm Product In Carton)(13) 1x Handle A (8mm Supplied Separately)(14) 2 Bottom Guide Blocks Part B (L+R) x (15) 1 Bottom Guide Blocks Part A x (16) 1x Drip Strip
(18) 2x Drip Strip End Cap (L+R)(19) 1x Wall Profile B
(17) 1x Moving Panel
(31) 2x Inner Washer(30) 1x Outer Washer(29) 2x Screws M5x20 (Sink Head)(28) 1x Cover Cap (Guide Rail)
(25) 1x Wedge Gasket Seal(26) Wall Profile1x
(24) 1x Fixed Panel (23) 1x Seal A(22) 4x Screws 4x16
(20) 1x Seal B
(32) 1x Wall Fixing Seat(33) 1x Adjustment Bracket(34) 4x Bump Stops(35) 2x Rollers(36) 2x Screw Caps(37) 2x Screws(38) 2x Glass-Fitting Parts
SIDEPANEL BOX
(22)
(21) 6x PVC Hoses
(27)
(27) 1x Wall Post Cover Cap B
4
MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS
SHOWER PANEL / DOOR
Step 2 FITTING FIXED PANEL
6mm x4
x44x30
1
x44
3
5
x42
10mm
1
2
Step 1 DRILLING WALL PROFILE TO THE WALL SLIDING DOOR RECESS INSTALLATION
5
Step 3 ASSEMBLING THE GUIDE RAIL AND MARKING THE WALL
Step 4 TAKE APART THE GUIDE RAIL
1
3
5
1
2
4
2 x2
x2
6
Step 5 SECURING THE WALL FIXING SEAT
Step 6 SLIDE GUIDE RAIL ON TO THE WALL FIXING SEAT
Ø6mm
2
3 4
1
3
4
7
2
1
MAX:20mm
6
MAX:20mm
5
x2
x2
x2
x2
1
H2O
2
3
5
6
748mm glass
2
10mm glass
7
inside
Step 7 FITTING THE WEDGE GASKET SEAL
Step 8 FITTING THE BOTTOM DRIP STRIP
Step 9 FITTING THE ROLLERS
1
2
3
4
5
6
8
x2
x2
x2
View from inside
1
2
3
4
Step 10 FITTING THE SEAL AND ADJUST DOOR STOP
Adjust
9
Step 11 ADJUSTING THE MOVING PANEL
OUTSIDE
OUTSIDE
4x30
x4
x4
6mm
x4
2
1 5
x4
4
6
3 x47
Step 12 INSTALLING THE WALL PROFILE
10
Step 14 SILICONE THE OUTSIDE EDGES
Step 13 FITTING THE TOP CAP AND SEAL AND FITTING THE HANDLE
INSIDE
INSIDE
10mm glass
8mm glass
Allow 24 hours for silicone to dry before use. Silicone on the
outside edge only, NOT THE INSIDE
11
MAKE SURE THE TRAY IS LEVEL, USING A SPIRIT LEVEL, BEFORE INSTALLING THIS
SHOWER PANEL / DOOR
Step 1 DRILLING WALL PROFILE TO THE WALL
6mm x8
x8
x8
4x30
x84
2
5
3
10mm
CORNER INSTALLATION WITH A SIDE PANEL
Step 2 ASSEMBLING THE FIXED PANELS, WASHER, COVER CAP AND WEDGE GASKETS
x2
x2
x23
4
2
x2
x2
x2
1
5
6
H2O
MAX:20MM
7
8
9
12
Step 3 FITTING THE BOTTOM DRIP STRIP
3
48mm glass
2 5
6
7
10mm glass
Step 4 FITTING THE ROLLERS
1
2
3
4
5
6
x2
x2
x2
View from inside
1
2
3
4
Step 5 FITTING THE SEAL AND ADJUSTING DOOR STOP
Adjust
Step 6 ADJUSTING THE MOVING PANEL
OUTSIDE
OUTSIDE
13
14
Step 8 SILICONE THE OUTSIDE EDGES
Step 7 SECURING THE PROFILE AND COVER SEAL AND FITTING THE TOP CAP
2
1 4
3
5 x4
x4 6
Allow 24 hours for silicone to dry before use. Silicone on the
outside edge only, NOT THE INSIDE
Product name: 8/10mm Sliding Door And Side Panel
Product code: DSD1202 / DSD1402 / DSD1602 / DSD1702 DSD1203F / DSD1203M
Customer help line number: 0344 804 48 48
CARE AND MAINTENANCE
COMMITMENT TO QUALITY
1) AFTER CARE INSTRUCTIONS
2) MAINTENANCE
Regularly clean your shower product with warm soapy water
Clean the plastic parts with a cloth and mild detergent. Never
use any abrasive creams, dissolvents, acetone or detergents
and disinfectants that contain chlorine. The supplier acceptsno liability for any type of use of care other than those contained
in these instructions. The supplier reserves the right to introduce
technical changes without notice.
It is our intention that the quality and functions of this productare of the highest standard. If you require help we advise you
firstly contact a competent plumber. However we understand that
this may not always be the case, so should you experience
any problems please contact our customer services quoting
the following:
to prevent lime scale build up. Do not use abrasive cleaning
fluids or materials, or strong chemical cleaners as this will
damage the product surface.
DSP802 / DSP902 / DSP803 / DSP903
15
INSTALLERS NOTES
16
INSTALLERS NOTES
17
INSTALLERS NOTES
18
The packaging you have received with your product is 100% recyclable.It must be disposed of in a safe and environmentally friendly way.
We suggest you take it to the local landfill site and discard in the designated bins.
V02/08/2017
Victoria Plum Limited, Bridgehead Business Hessle, HU13 0DG
Park
17
EN 14428:2015
DOP No.:J170320003-1
Shower enclosures with aluminiumprofiles and safety glass
Essentialcharacteristics
Performance Harmonisedtechnical
specificationCleanability
Impactresistance/shatter
properties
Pass
Pass
PassDurability
Clause 4.2 of EN 14428:2015
Clause 4.3 of EN 14428:2015
Clause 4.4 of EN 14428:2015