811 4x3-13a40_perf

20
PERFORMANCE CURVES PERFORMANCE DARE TO COMPARE

Upload: vlachoreyes

Post on 27-Oct-2014

70 views

Category:

Documents


3 download

DESCRIPTION

crvas bombas wriswold

TRANSCRIPT

Page 1: 811 4x3-13A40_PERF

P e r f o r m a n c e c u r v e s

P e r f o r m a n c e d a r E T o c o m P a r e

Page 2: 811 4x3-13A40_PERF
Page 3: 811 4x3-13A40_PERF

table of contents

PumP Size RPm PAGe #

1 1/2 x 1 - 6AA 1800 1 3600 1

3 x 1 1/2 - 6AB 1800 1 3600 1

3 x 2 - 6AC 1800 1 3600 1

LF 1 1/2 x 1 - 8AA 1800 2 3600 2

1 1/2 X 1 - 8AA 1800 2 3600 2

3 X 1 1/2 - 8AB 1800 2 3600 2

3 X 2 - 8 A60 1800 3 3600 3

4 X 3 - 8 A70 1200 3 1800 3

4 X 3 - 8G A70 1800 3 3600 3

LF 2 X 1 -10 A05 1800 4

3600 4

2 X 1 - 10 A05 1800 4 3600 4

3 X 1 1/2 - 10 A50 1800 4 3600 4

3 X 2 - 10 A60 1200 5 1800 5 3600 5

4 X 3 - 10 A70 1200 5 1800 5 3600 5

4 X 3 - 10H A40 1200 6 1800 6

PumP Size RPm PAGe #

6 X 4 - 10G A80 1200 6 1800 6

3600 6

6 X 4 - 10H A80 1200 6 1800 7

LF 3 X 1 1/2 - 13 A20 1800 7 3600 7

3 X 1 1/2 - 13 A20 1200 7 1800 7

3600 7

3 X 2 - 13 A30 1200 8 1800 8 3600 8

4 X 3 - 13 A40 1200 8 1800 8 3600 8

6 X 4 - 13 A80 1200 9 1800 9

8 X 6 - 13 A90 1200 9 1800 9

10 X 8 - 13 A100 1200 9

1800 9

8 X 6 - 15 A110 1200 10 1800 10

10 x 8 - 15 A120 900 10 1200 10

10 x 8 - 15 G A120 1200 10 1800 10

6 x 4 - 17 A105 1200 116 x 4 - 17 A105 1800 11

811 Dimensional Data 12

8ll Specifications Back Cover13

Page 4: 811 4x3-13A40_PERF

Performance curves

Griswold pump company 1 Grs-10010-c-01

1 1/2 x 1 - 6AA 1800 RPm Curve: G-1801

3 x 1 1/2 - 6AB 1800 RPm Curve: G-1802 3 x 1 1/2 - 6AB 3600 RPm Curve: G-3602

3 x 2 - 6AC 1800 RPm Curve: G-1803 3 x 2 - 6AC 3600 RPm Curve: G-3603

1 1/2 x 1 - 6AA 3600 RPm Curve: G-3601

Page 5: 811 4x3-13A40_PERF

Performance curves

Grs-10010-c-01 2 Griswold pump company

LF1-1/2 x 1 - 8 AA 1800 RPm Curve: GLF-1804 LF1-1/2 x 1 - 8 AA 3600 RPm Curve: GLF-3604

1-1/2 x 1 - 8 AA 1800 RPm Curve: G-1804 1-1/2 x 1 - 8 AA 3600 RPm Curve: G-3604

3 x 1-1/2 - 8 AB 1800 RPm Curve: G-1805 3 x 1-1/2 - 8 AB 3600 RPm Curve: G-3605

Page 6: 811 4x3-13A40_PERF

Performance curves

Griswold pump company 3 Grs-10010-c-01

4 x 3 - 8G A70 1800 RPm Curve: G-1809

3 x 2 - 8 A60 1800 RPm Curve: G-1807 3 x 2 - 8 A60 3600 RPm Curve: G-3607

4 x 3 - 8 A70 1200 RPm Curve: G-1208 4 x 3 - 8 A70 1800 RPm Curve: G-1808

4 x 3 - 8G A70 3600 RPm Curve: G-3609

Page 7: 811 4x3-13A40_PERF

Performance curves

Grs-10010-c-01 4 Griswold pump company

LF2 x 1 - 10 A05 1800 RPm Curve: GLF-1810 LF2 x 1 - 10 A05 3600 RPm Curve: GLF-3610

2 x 1 - 10 A05 1800 RPm Curve: G-1810 2 x 1 - 10 A05 3600 RPm Curve: G-3610

3 x 1-1/2 - 10 A50 1800 RPm Curve: G-1811 3 x 1-1/2 - 10 A50 3600 RPm Curve: G-3611

Page 8: 811 4x3-13A40_PERF

Performance curves

Griswold pump company 5 Grs-10010-c-01

3 x 2 - 10 A60 1800 RPm Curve: G-1812

3 x 2 - 10 A60 3600 RPm Curve: G-3612

3 x 2 - 10 A60 1200 RPm Curve: G-1212

4 x 3 - 10 A70 1200 RPm Curve: G-1213

4 x 3 - 10 A70 1800 RPm Curve: G-1813 4 x 3 - 10 A70 3600 RPm Curve: G-3613

Page 9: 811 4x3-13A40_PERF

Performance curves

Grs-10010-c-01 6 Griswold pump company

4 x 3 - 10H A40 1200 RPm Curve: G-1214 4 x 3 - 10H A40 1800 RPm Curve: G-1814

6 x 4 - 10G A80 1200 RPm Curve: G-1215 6 x 4 - 10G A80 1800 RPm Curve: G-1815

6 x 4 - 10G A80 3600 RPm Curve: G-3615 6 x 4 - 10H A80 1200 RPm Curve: G-1216

Page 10: 811 4x3-13A40_PERF

Performance curves

Griswold pump company 7 Grs-10010-c-01

6 x 4 - 10H A80 1800 RPm Curve: G-1816 LF 3 x 1-1/2 - 13 A20 1800 RPm Curve: GLF-1817

LF 3 x 1-1/2 - 13 A20 3600 RPm Curve: GLF-3617 3 x 1-1/2 - 13 A20 1200 RPm Curve: G-1217

3 x 1-1/2 - 13 A20 1800 RPm Curve: G-1817 3 x 1-1/2 - 13 A20 3600 RPm Curve: G-3617

Page 11: 811 4x3-13A40_PERF

Performance curves

Grs-10010-c-01 8 Griswold pump company

3 x 2 - 13 A30 1800 RPm Curve: G-1818

3 x 2 - 13 A30 3600 RPm Curve: G-3618 4 x 3 - 13 A40 1200 RPm Curve: G-1219

3 x 2 - 13 A30 1200 RPm Curve: G-1218

4 x 3 - 13 A40 1800 RPm Curve: G-1819 4 x 3 - 13 A40 3600 RPm Curve: G-3619

Page 12: 811 4x3-13A40_PERF

Performance curves

Griswold pump company 9 Grs-10010-c-01

6 x 4 - 13 A80 1800 RPm Curve: G-1820

8 x 6 - 13 A90 1800 RPm Curve: G-1821

6 x 4 - 13 A80 1200 RPm Curve: G-1220

8 x 6 - 13 A90 1200 RPm Curve: G-1221

10 x 8 - 13 A100 1200 RPm Curve: G-1222 10 x 8 - 13 A100 1800 RPm Curve: G-1822

Page 13: 811 4x3-13A40_PERF

Performance curves

Grs-10010-c-01 10 Griswold pump company

10 x 8 - 15G A120 1800 RPm Curve: G-1825

8 x 6 - 15 A110 1200 RPm Curve: G-1223 8 x 6 - 15 A110 1800 RPm Curve: G-1823

10 x 8 - 15G A120 1200 RPm Curve: G-1225

10 x 8 - 15 A120 900 RPm Curve: G-0824 10 x 8 - 15 A120 1200 RPm Curve: G-1224

Page 14: 811 4x3-13A40_PERF

Performance curves

Griswold pump company 11 Grs-10010-c-01

6 x 4 - 17 A105 1800 RPm Curve: G-18276 x 4 - 17 A105 1200 RPm Curve: G-1227

Page 15: 811 4x3-13A40_PERF

Performance curves

Grs-10010-c-01 12 Griswold pump company

ROTATIONROTA

TIO

N

811 Dimensional Data

Grs-10010-c-01 12 Griswold pump company

Page 16: 811 4x3-13A40_PERF

Griswold pump company 13 Grs-10010-c-01

GRiSWOLD PumP COmPANYmodel 811 ANSi B73.1 Specifications

1.0 Pump Design 1.1 The pump must conform in all respects to the latest edition of ANSI Specification B73.1M. 1.2 The pump should be back pullout design. A machined fit between the pullout assembly and the casing to insure alignment is required. 1.3 Pump will be top centerline, self-venting discharge. 1.4 100% of the pump shall be manufactured in the USA excluding outside purchased items like bearings and hardware that may or may not be produced in the USA.

2.0 Casing 2.1 Class 150 pumps shall incorporate class 300 wall thickness as standard, extending casing life under corrosive / erosive conditions. 2.2 Casing shall be machined as to accommodate a fully confined casing gasket to prevent leakage. 2.3 The casing shall be furnished with a minimum 1/8” corrosion allowance. 2.4 The pump casing, when produced in Ductile Iron, Stainless Steel or CD4Mcu, shall include a drain plug and a discharge tap connection.

3.0 Impeller 3.1 A fully open impeller shall be provided to facilitate the handling of solid and stringy material. 3.2 The impeller shall be self-tightening. 3.3 The impeller shall be furnished with back pump out vanes to reduce pressure in the seal chamber and to minimize axial thrust. 3.4 The pump shall be provided with an open impeller design to allow for re-establishment of original clearances and hydraulic performance and efficiencies without pump disassembly. 3.5 Impeller connection to the shaft shall allow for metal-to-metal contact with a control squeeze TeflonÆ o-ring. 3.6 The impeller shall be balanced to minimize vibration in accordance with ISO 1940 Grade 6.3 after final machining. 3.7 The impeller shall be produced with ultra-smooth investment castings to improve hydraulic and mechanical balance.

4.0 Bearing Frame and Adapter 4.1 Non-pressure retaining castings (bearing housing, medium - large - extra large bearing frames, frame feet) shall be produced in cast iron with a minimum tensile strength of 30,000 lbs. 4.2 Pressure retaining castings (small bearing frame, all adapters) shall be produced in Ductile Iron with a minimum tensile strength of 65,000 lbs. 4.3 Interior surfaces of all bearing frames shall be coated with a Fusion Bonded Epoxy Coating to provide for long-term quality and cleanliness of the lubricating oil. 4.4 The bearing frames shall be assembled in a clean room environment to eliminate contamination. 4.5 The bearing frame and adapter mating surfaces must be machined with a register fit to guarantee precise alignment. Additionally, dowel pins shall be utilized to eliminate torsion. 4.6 The bearing housing with adjusting bolts shall be provided to allow for axial adjustment of the impeller to regain hydraulic performance and efficiencies without pump disassembly. 4.7 To minimize shaft misalignment due to flange loading on the pump, the frame foot, if separate from the bearing frame, shall be rigidly attached at two points and constructed of cast iron with a minimum tensile strength of 30,000 lbs. 4.8 The shaft shall be provided to keep deflection within ANSI B73.1 limits at all operating points. 4.9 The shaft sleeve when provided will be hook type sleeve 316 stainless steel as a minimum or sleeveless solid shafts as an option. 4.10 Bearing shall be designed for a minimum life (Lπ10) of two years and a 10-year average life as required by the latest edition of ANSI B73.1M specifications as manufactured by SKF or equal. 4.11 Radial and thrust bearings shall not be pressed onto the shaft. Bearings shall be installed utilizing stress-free bearing induction heater. 4.12 To prevent thrust bearing loosening during pump operation, thrust bearings shall be positively locked to the shaft by means of a locknut and lock washer. 4.13 To retain lubricant and prevent contamination, bronze InproÆ labyrinth oil seals shall be provided. 4.14 A one-inch sight glass with reflective baffle shall be provided to monitor oil level and condition. 4.15 A magnetic drain plug shall be provided to collect damaging metallic particles. 4.16 Condition-monitoring sites shall be provided to facilitate consistent checking of vibration and temperature. 4.17 If lubricant cooling is required a finned tube-cooling element shall be provided. 4.18 In high load applications beyond ANSI 811M bearing frame limits an 811L frame shall be specified incorporating an oversized shaft with an oil slinger, higher load carrying radial bearing and duplex angular contact thrust bearings.

5.0 Seal Chamber 5.1 Seal chambers shall be engineered to provide the optimum seal environment for heat dissipation, solids, trapped air and vapor.

6.0 Pump Bases 6.1 A rigid, high-strength base shall be provided to insure pump-to-motor shaft misalignment not to exceed 0.005” due to base plate distortion.

7.0 Coupling Guard 7.1 A coupling guard shall be provided with the pump that conforms to both ANSI and OSHA requirements.

8.0 Warranty 8.1 Pumps shall be backed by a 5-year whole pump unconditional guarantee against defects in material and workmanship.

Page 17: 811 4x3-13A40_PERF

Notes

Page 18: 811 4x3-13A40_PERF

Notes

Page 19: 811 4x3-13A40_PERF

Notes

Page 20: 811 4x3-13A40_PERF

Printed in the U.S.A. Copyright 2009 Griswold Pump Company GRS-10010-C-01

22069 Van Buren Street • Grand Terrace, CA 92313-5607Phone: (229) 226-5255 • (800) 843-9222

Fax (229) 226-5567 • (909) 422-1787email: [email protected]

website: www.griswoldpump.com Printed in the U.S.A. Copyright 2009 Griswold Pump Company GRS-10000-T-01