864 ho nb ember-fyre burner w/ lodge pine logs ... ho nb packing list ember-fyre burner assembly log...

10
864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs Installation Instructions (SKU 96900144) Page 1 of 10 17601715.docx — 8/8/12 © Travis Industries, Inc. Compatibility 864 HO NB Packing List Ember-Fyre Burner Assembly Log Set With Embers and Rock Wool Grate Assembly Front & Rear Andiron Brackets Burner Air Deflectors (Natural Gas and LP) Rivet (for LP installations only) Air Deflectors Installation Tips If using LP, convert the appliance before installing the burner. Make sure to have the firebacks for the appliance on hand. They will be installed before burner installation. Installation Warnings The logs are fragile, especially after being exposed to heat. Make sure the gas control valve is OFF and the heater is cool before servicing. Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury. The burner must be correctly positioned before installing the logs. Make sure the burner is fully seated and the pilot is properly aligned.

Upload: phunglien

Post on 19-May-2018

219 views

Category:

Documents


2 download

TRANSCRIPT

 

864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs Installation Instructions (SKU 96900144)

 

 

Page 1 of 10 17601715.docx — 8/8/12 © Travis Industries, Inc.

Compatibility

864 HO NB

Packing List

Ember-Fyre Burner Assembly Log Set With Embers and Rock Wool Grate Assembly

Front & Rear Andiron Brackets Burner Air Deflectors (Natural Gas and LP) Rivet (for LP installations only) Air Deflectors

Installation Tips

If using LP, convert the appliance before installing the burner.

Make sure to have the firebacks for the appliance on hand. They will be installed before burner installation.

Installation Warnings

The logs are fragile, especially after being exposed to heat.

Make sure the gas control valve is OFF and the heater is cool before servicing.

Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

The burner must be correctly positioned before installing the logs. Make sure the burner is fully seated and the pilot is properly aligned.

 

864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs Installation Instructions (SKU 96900144)

 

 

Page 2 of 10 17601715.docx — 8/8/12 © Travis Industries, Inc.

1. Install the front and side air deflectors. On older models, these are pre‐installed at the factory. 

Note that the screw holes are circled below. 

 

The illustration below shows the air deflectors installed. 

 

   

 

864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs Installation Instructions (SKU 96900144)

 

 

Page 3 of 10 17601715.docx — 8/8/12 © Travis Industries, Inc.

2. Install the firebacks. 

3. Install the burner as shown below. 

 

NOTE: When installing the air deflectors, make sure the locking tabs face toward the front of the burner. 

NOTE: The NG and LP are deflectors are shaped differently, and the LP has a notch at the bottom. 

 

4. Bend up the tab on the burner as shown below. 

NG (Natural G as) LP (P ropane) 

Bend this tab up; it is shipped flat. 

This notch indicates LP.

 

864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs Installation Instructions (SKU 96900144)

 

 

Page 4 of 10 17601715.docx — 8/8/12 © Travis Industries, Inc.

Special Instructions for LP

Install the rivet included with this kit into the hole shown below.

 

Andiron Installation (Optional)

The optional andirons should be installed before installing the logs. See the directions below for installation.

1 Remove the grate from the firebox. Remove and discard the two andiron prongs (see step “a” to the right). NOTE: The nuts do not need to be removed, they can be loosened to remove the prongs.

2 Attach the andiron brackets

(shipped with the burner) to the grate (see step “b”).

3 Attach the andirons using the

screws included with the andirons (see step “c”).

 

5/32 Hex Wrench

11/32" Nutdriver

a

b

c

 

864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs Installation Instructions (SKU 96900144)

 

 

Page 5 of 10 17601715.docx — 8/8/12 © Travis Industries, Inc.

Log Set Installation

Back Log

Install the back log as shown below. Make sure the bottom of the log lays flat against the two steel platforms on the burner.  Slide the log forward (NG units) or backward (LP units).

   

 

Bend this tab up; if not done previously. 

NG units: Slide the log forward. LP units: Slide the log backward.

 

864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs Installation Instructions (SKU 96900144)

 

 

Page 6 of 10 17601715.docx — 8/8/12 © Travis Industries, Inc.

Right Log

Install the right log as shown below. Position the log so the back edge contacts the metal plate on the burner and does not cover any burner holes.

   

 

 

864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs Installation Instructions (SKU 96900144)

 

 

Page 7 of 10 17601715.docx — 8/8/12 © Travis Industries, Inc.

Middle Log

Install the middle log as shown below.

   

   

Left Log

Install the left log as shown below.

   

 

 

864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs Installation Instructions (SKU 96900144)

 

 

Page 8 of 10 17601715.docx — 8/8/12 © Travis Industries, Inc.

Left Twig

Install the left twig as shown below.

   

 

Right Twig

Install the right twig as shown below.

   

 

864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs Installation Instructions (SKU 96900144)

 

 

Page 9 of 10 17601715.docx — 8/8/12 © Travis Industries, Inc.

Center Twig

Install the center twig as shown below.

   

 

 

864 HO NB Ember-Fyre Burner W/ Lodge Pine Logs Installation Instructions (SKU 96900144)

 

 

Page 10 of 10 17601715.docx — 8/8/12 © Travis Industries, Inc.

Ember Installation

Install the embers as shown below. Make sure to cover the screws on the burner and any fireback seams with embers to create an aesthetic firebox.

   

   

Rock Wool Installation

The included rock wool is placed on top of the burner to enhance the glow from the burner. The rock wool works best when it is applied in a very thin, porous layer. The best method for applying the rock wool is to brush it on to the burner. Compress a clump of rock wool between your thumb and forefinger. Use a stiff brush to apply a thin layer of rock wool fibers onto the burner. Do not use the entire bag of rock wool. Use only a small amount and save the remainder. Over-use of rock wool will diminish the glow and may cause sooting or other adverse conditions.