9312 compact od site specification apr09

Upload: mansour14

Post on 03-Jun-2018

222 views

Category:

Documents


0 download

TRANSCRIPT

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    1/56

    UNCONTROLLED COPY: The master of this document is stored on an electronic

    database and is "write protected"; it may be altered only by authorized persons. While

    copies may be printed, it is not recommended. Viewing of the master electronicallyensures access to the current issue. Any hardcopies taken must be regarded as

    uncontrolled copies.

    ALCATEL-LUCENT CONFIDENTIAL: The information contained in this document is

    the property of Alcatel-Lucent. Except as expressly authorized in writing by Alcatel-

    Lucent, the holder shall keep all information contained herein confidential, shall

    disclose the information only to its employees with a need to know, and shall protect

    the information from disclosure and dissemination to third parties. Except as expressly

    authorized in writing by Alcatel-Lucent, the holder is granted no rights to use the

    information contained herein. If you have received this document in error, please notify

    the sender and destroy it immediately.

    2009 Alcatel-Lucent

    All Rights Reserved

    Pre

    liminary

    Alcatel-Lucent 9312 Compact Node B

    Outdoor Site Specification

    Installation Method 06-6273

    April 29, 2009

    Issue Number: 2.02

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    2/56

    0 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    3/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 1

    April 29, 2009 Method 06-6273

    Preliminary

    Table of Contents

    1.0 General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

    1.1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

    1.2 Sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.3 Reason for Reissue. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

    2.0 Material Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

    2.1 Required Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

    3.0 Precautions and Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

    3.1 Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

    4.0 Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

    4.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

    4.1.1 9312 Compact OD Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

    4.1.2 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

    4.1.3 Dimensions and Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104.1.3.1 9312 Compact OD Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

    4.1.3.2 Details of Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

    4.1.4 Equipment Packaging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

    4.1.5 Environmental and Mechanical Conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

    4.1.6 User Compartment Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

    4.1.6.1 User Racks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

    4.1.6.2 User ICO. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

    4.1.6.3 RETA AISG Optional (Through TRDU AISG only) . . . . . . . . . . . . . . . . . . . . . 20

    4.1.6.4 LP PCM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

    4.1.6.5 IEAM Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

    4.2 9312 Compact OD Power Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

    4.2.1 AC Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

    4.2.2 AC Consumption of 9312 Compact OD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

    4.3 Site Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

    4.3.1 Site Access. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

    4.3.1.1 Easy Access Site Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

    4.3.1.2 Difficult Access Site Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

    4.3.2 Cabinet Handling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

    4.3.2.1 Lifting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

    4.3.2.2 Horizontal Moving. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

    4.3.2.3 Moving a Depopulated Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

    4.3.3 Floor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

    4.3.3.1 Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

    4.3.3.2 Floor Flatness. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

    4.3.4 Pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 294.3.4.1 Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

    4.3.4.2 Cabinet Securing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

    4.3.5 Wall. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

    4.3.5.1 Resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

    4.3.5.2 Flatness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

    4.3.5.3 Cabinet Securing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

    4.3.6 Site Dimensioning Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

    4.3.6.1 Cabinet Dimensions and Distance Constraint . . . . . . . . . . . . . . . . . . . . . . . . 30

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    4/56

    2 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.3.6.2 Site Layouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

    4.3.6.3 Cabinets Orientation in Outdoor Site. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

    4.3.6.4 Input Constraint of Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

    4.4 9312 Compact OD Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

    4.4.1 9312 Compact OD Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

    4.4.2 Earth Plate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 354.4.3 Cable Tray. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

    4.4.3.1 Solution 9312 Compact OD Alone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

    4.5 Site Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

    4.5.1 Cabinet Securing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

    4.5.2 Cabinet Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

    4.5.2.1 9312 Compact OD External Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

    4.5.2.2 Ground Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

    4.5.2.3 BTS AC Supply Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

    4.5.3 External Cables Marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

    4.5.4 Distribution Frame for PCM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

    4.5.5 Feeders and Antenna System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

    4.5.6 Lightning Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

    4.5.7 Radio Cables Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

    4.6 Final State of Site Preparations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

    5.0 References . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51

    6.0 Appendices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53

    6.1 Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

    6.2 Terms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

    End of Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    5/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 3

    April 29, 2009 Method 06-6273

    Preliminary

    Figures

    Figure 1 Cabinet Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

    Figure 2 UTRAN-UMTS Terrestrial Radio Access Network . . . . . . . . . . . . . . . . . . . . . . . . . 9

    Figure 3 9312 Compact OD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Figure 4 9312 Compact OD Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

    Figure 5 9312 Compact OD - Outdoor Cabinet Footprint . . . . . . . . . . . . . . . . . . . . . . . . . 12

    Figure 6 Cabinet, Plinth and Pallet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

    Figure 7 User Compartment View. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

    Figure 8 User Rack Internal Space . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

    Figure 9 C-User ICOs Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

    Figure 10 RETA AISG . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

    Figure 11 LPPCM Module Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

    Figure 12 IEAM Module layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

    Figure 13 DC Power Consumption and BBUP Time (Compact) with TRDU 40W . . . . . . . 23

    Figure 14 DC Power Consumption Vs TRDU Output Power . . . . . . . . . . . . . . . . . . . . . . . 24

    Figure 15 Access Within the Building . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

    Figure 16 9312 Compact OD Cabinet Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

    Figure 17 9312 Compact OD Cabinet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

    Figure 18 Minimum Space Required on Site Layout for 2 Compact OD Side by Side . . . . 32

    Figure 19 Minimum Space Required on Site Layout with 2 Compact OD - Back to Back . 32

    Figure 20 Floor Solution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

    Figure 21 Wall or Pole Solution. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

    Figure 22 Main Site Circuit Breaker (Single Phase) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

    Figure 23 Drilling Template. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

    Figure 24 9312 Compact OD Bulkhead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

    Figure 25 Grounding Kits on Feeders . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

    Figure 26 Example of RF Link without UMTS TMA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    6/56

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    7/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 5

    April 29, 2009 Method 06-6273

    Preliminary

    1.0 General Information

    1.1 Description

    Purpose:This document defines the specifications covering theselection and preparation of site that must receive the Compact.

    The criterion, which allows classifying a site as an easy- or difficult-access site, is given.

    Equipment:This document applies to the deployment of 9312Compact OD. The cabinet is available on the following electricalsupplying mode:

    An Outdoor AC version powered by a power plant.

    The internal user space (2U 19" + 2 U 9.5") can be used to connect

    user equipment (LPPCM module, IEAM Module optional or CCU ofRETA).

    Application:This document is used to define site requirement.

    Service Impact:None

    Skill Level Requirement:None

    1.2 Sequence

    This is a stand-alone method.

    1.3 Reason for Reissue

    Reason for update:

    202 Update after internal review

    Closes Alert(s): None

    Closes CR(s): None

    Replaces Method 06-6273 dated: February 27, 2009.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    8/56

    6 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    2.0 Material Requirements

    2.1 Required Documents

    Regional Installation Safety Manuals (ISM)

    Installation Method can be find at:

    https://wcdma-ll.app.alcatel-lucent.com/livelink/livelink.exe?func=ll&objId=36528788&objAction=browse&sort=name&viewType=1

    45-9003 Alcatel-Lucent 9312 Compact Product Safety InstallRequirements

    No other materials are required to perform this method.

    https://wcdma-ll.app.alcatel-lucent.com/livelink/livelink.exe?func=ll&objId=36528788&objAction=browse&sort=name&viewType=1
  • 8/11/2019 9312 Compact OD Site Specification Apr09

    9/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 7

    April 29, 2009 Method 06-6273

    Preliminary

    3.0 Precautions and Preparations

    3.1 Precautions

    Observe the general safety precautions against personal injury andequipment damage outlined in the regional Installation Safety Manual atall times.

    Please refer to the 45-9003 Alcatel-Lucent 9312 Compact ProductSafety Install Requirements

    External alarm protection: The external alarms protection aremandatory when external alarms are used. They must be protected bythe optional IEAM module (for primary and secondary protectionmodule).

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    10/56

    8 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.0 Specification

    4.1 Overview

    4.1.1 9312 Compact OD Characteristics

    In a UMTS network, the 9312 Compact OD provides the interfacebetween the RNC and the User Equipment.

    The 9312 Compact OD platform is part of the UTRAN architecture andacts as a NodeB radio part.

    Figure 1

    TRDU 1

    TRDU 2

    TRDU 3

    IEAM

    LPPCM

    xCEMu 1xCEMu 2xCEMu 3

    xCEMu 4

    xCCMu

    CDAC

    Batteries

    cUSER ICOSpace

    Supply Unit

    Cabinet Overview

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    11/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 9

    April 29, 2009 Method 06-6273

    Preliminary

    Figure 2 UTRAN-UMTS Terrestrial Radio Access Network

    - A 9312 Compact OD cabinet overview is given in Figure 3

    Figure 3 9312 Compact OD

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    12/56

    10 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.1.2 Specifications

    All mechanical sub racks and mechanical support systems requiredfor the installation, transport and operation of the 9312 Compact ODwireless equipment to be housed within

    An optional User Interconnection module (C-USER ICO)

    An optional IEAM (external alarm)

    Manufacturing Commissioning Alarm module (MCA)

    RF ICOr

    An interconnection box including AC power distribution

    Distribution Unit (CPSU)

    A universal cooling unit with AC heaters

    4.1.3 Dimensions and Weight

    4.1.3.1 9312 Compact OD Dimensions

    Table 1 9312 Compact OD Dimensions

    9312 Compact OD

    Height 1200mm (47.24 in)

    Height with plinth 1370mm (53.93 in)

    Depth 700 mm (27.55 in)

    Width 580 mm (22.83 in)

    Figure 4below shows the 9312 Compact OD dimensions and Figure 5display the cabinet footprint.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    13/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 11

    April 29, 2009 Method 06-6273

    Preliminary

    Figure 4

    Below View

    Front

    Right side

    Behind

    Left side

    Front View

    Top View

    9312 Compact OD Dimensions

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    14/56

    12 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    Figure 5 9312 Compact OD - Outdoor Cabinet Footprint

    1280mm

    7007

    00

    1145

    Top View

    100

    4.1.3.2 Details of Weight

    The table hereafter gives the weight of all modules and bare cabinet:

    Table 2 Modules and Bare Cabinet Weights

    Compo-

    nent

    Weight Qty Weight With

    options

    Weight Without

    options

    lbs Kg

    Pre cabled

    cabinet

    264.55 120 1 120 kg (264.55 lbs) 120 kg (264.55 lbs)

    TRDU 2100

    MHz

    23.15 10.5 3 31.5 kg (69.45 lbs) 31.5 kg (69.45 lbs)

    xCEMu 2.65 1.2 4 4.8 kg (10.60 lbs) 4.8 kg (10.60 lbs)

    xCCMu 3.53 1.6 1 1.6 kg (3.53 lbs) 1.6 kg (3.53 lbs)

    CPSU with

    one rectifier

    15.65 7.1 1 7.1 kg (15.65 lbs) 7.1 kg (15.65 lbs)

    Rectifier 6.5 2.95 1 5.9 kg (13 lbs) 5.9 kg (13 lbs)

    MCA 1.1 0.5 1 0.5 kg (1.1 lbs) 0.5 kg (1.1 lbs)

    Batteries 33.07 15 4 60 kg (132.28 lbs) 60 kg (132.28 lbs)

    User Space

    (up to)*

    8.8 4 3 12 kg (26.40 lbs) 0

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    15/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 13

    April 29, 2009 Method 06-6273

    Preliminary

    * Not add in the subtotal

    CCU Mod-

    ule RETA

    (optional)

    2,42 1,1 1 1,1 kg (2,42 lbs) 0

    LPPCM

    (optional)

    2.2 1 1 1 kg (2.2 lbs) 0

    IEAM

    (optional)

    2.2 1 1 1 kg (2.2 lbs) 0

    c-USER-

    ICO

    (optional)

    2.2 1 1 1 kg (2.2 lbs) 0

    Configura-

    tion cabling

    (estimated)

    13,22 6 1 6 kg (13,22 lbs) 6 kg (13,22 lbs)

    Plinth 24.25 11 1 11kg (24.25 lbs) 11kg (24.25 lbs)

    Subtotal 251.5 kg (554.46

    lbs)

    247.4 kg (545.42

    lbs)

    Pallet (esti-

    mated)

    10 kg (22.04 lbs) 10 kg (22.04 lbs)

    Total 261.5kg (576.5 lbs) 257.4 kg (567.47

    lbs)

    Table 2 Modules and Bare Cabinet Weights

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    16/56

    14 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.1.4 Equipment Packaging

    The cabinet is fully assembled in conventional delivery conditions,shipped on its wooden pallet.

    Note: A plinth is delivery with the cabinet.

    The wooden pallet weight around 16 kg (35,27 lb) TBC

    Until the cabinet is disassembled from its wooden pallet, the packagingincreases the cabinets weight and dimensions during installation phase(moving).

    For sites with difficult access, the 9312 Compact OD cabinet is orderedfully equipped, and can be depopulated in warehouse for delivering onsite. The modules that have to be inserted in the cabinet on site aredelivered in specific protective packaging.

    Figure 6 Cabinet, Plinth and Pallet

    Plinth

    9312 Compact OD

    Wooden pallet

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    17/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 15

    April 29, 2009 Method 06-6273

    Preliminary

    4.1.5 Environmental and Mechanical Conditions

    The 9312 Compact OD is designed to be installed in outdoorenvironment with the following requirement

    Table 3 9312 Compact OD Environmental Requirements

    Requirement 9312 Compact OD

    Manufacturing The 9312 Compact OD is manufactured according to the WEEE(Waste of Electrical and Electronic Equipment) and RoHS

    (Restriction of Hazardous Substances) recommendations.

    Environmental Shall be compliant with R9 Reference Documents on page 51class4.1E except for: low temperature and high temperature, relative

    humidity levels (between 5% and 95%) condensing and high

    absolute humidity (36g/m3)

    Ingress Protection Weather resistant to prevent ingress of rain, snow, dust and othersolid foreign objects to a minimum level of IP55 as specified by R2Reference Documents on page 51

    Acoustic noise

    level

    for protected area

    The acoustic noise level shall comply with outdoor environment

    class 4.1E of R7 Reference Documents on page 51

    LwAd < 56 dB when t

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    18/56

    16 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    Impact on the Surrounding

    When fitted with its cooling system, the cabinet shall not amplifymechanically transmitted noise within the audible frequency range

    (20Hz - 20KHz)

    Note: The noise may be higher than the one previously indicated on thetable above due to the real configuration of the site (proximity ofwalls or any reflective surfaces). In this case, specific protectionsagainst noise can be added to comply with the localrecommendations.

    Electromagnetic Compatibility

    The 9312 Compact OD shall comply with different requirement in termsof EMC.

    For European market, 9312 Compact OD shall comply with therequirements stated in R12 and R15 Reference Documents on page 51

    In addition, the 9312 Compact OD Outdoor is compliant with the 3GPPspecification.

    Earthquake

    Vibration and

    Shock

    Once installed, the 9312 Compact OD shall meet the Zone 4 earthquake

    requirement as specified in R11Reference Documents on page 51

    Impact on the sur-

    roundingSee below

    Storage and

    Transport9312 Compact OD shall comply with R5 and R6Reference Documents

    on page 51

    Table 3 9312 Compact OD Environmental Requirements

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    19/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 17

    April 29, 2009 Method 06-6273

    Preliminary

    4.1.6 User Compartment Characteristics

    User equipment rack is proposed in all 9312 Compact OD cabinet.

    A standard user ico with up to 3 outputs -48V power supply and up to 4

    alarms is proposed on 9312 Compact OD, with maximal capacity:

    2x 1U 19" slot at the Side of the cabinet, which can be used for:

    2 x 1U for User Equipment (option, CCU RETA for example)

    2x 1/2U 9.5" at the side of the 2 x 1U which can be used for:

    1/2 U for IEAM-16 external alarms kit, optional.

    1/2 U for LPPCM (Lightning Protection PCM), optional.

    The optional C-User ICO provides connectivity for 4 DC -48V power

    supplies with associated fuses.

    C-User Ico is not part of the 2 1/2 U

    The power budget is 350W for the user equipment shelf.

    Figure 7 User Compartment View

    2X1U USERRACK 19"

    Li-ion InternalBattery (option)

    PCM LightningProtection (option)

    IEAM ExternalAlarm Kit (option)

    C-User ICO(option)

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    20/56

    18 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.1.6.1 User Racks

    Figure 8 User Rack Internal Space

    OEM modules nominal front panel dimensions shall be:

    Rack 19" (A on Figure 8):

    - Height available for OEM equipment: 2U (U = 44.45mm)

    - Width available for OEM equipment: Standard 19 inch (482.6mm)

    - Depth available for OEM equipment: 400mm

    Rack 1/2 19" (B on Figure 8):

    - Height available for OEM equipment: 2U (U = 44.45mm)

    - Width available for OEM equipment: around 1/2 19 inch (230mm)

    - Depth available for OEM equipment: 340 mm

    The fixing points shall be compatible with a standard 19 inch rack or1/2 19", and the mounting screws shall be in accordance with themetric standard (M6 x 15). The material of all the screws shall beStainless Steel.

    The total weight of all the OEM modules in a 9312 Compact ODcabinet user space shall not exceed 12 kg

    The OEM modules and cables shall function at full performance,when the local air temperature at the intake to the external surface ofthe OEM module, is within the range -5C to +50C.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    21/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 19

    April 29, 2009 Method 06-6273

    Preliminary

    4.1.6.2 User ICO

    Figure 9 C-User ICOs Views

    PWR IN

    J3

    J4

    J2

    PWR USER1

    PWR USER2

    PWR USER3

    J5

    J6ALARM

    USE ALARM

    The optional C-User ICO (USERICO) panels provides 3 x -48V DCpower ports with associated fuses. The maximum -48V DC power is350W supplied by the cabinet. A maximum of 3 power connections areavailable on 3 connectors MateN Lock female 3 contacts (-48V, 0V,GND). A alarm connector may provide 4 alarms on one SUB-D9 pinfemale connector.

    The OEM module shall generate a dry loop

    Note: If the alarm pin is connected to the ground (mechanical ground),there is no alarm. If the alarm pin is open, there is an alarm.

    Table 4 User Alarm Connector Pin Out

    PINS SIGNAL

    1 Unused

    2 Unused

    3 Alarm 4

    4 Alarm 3

    5 Alarm 2

    6 Alarm 1

    7 GND

    8 GND

    9 GND

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    22/56

    20 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.1.6.3 RETA AISG Optional (Through TRDU AISG only)

    The RETA permits the remote variable electrical tilting of cabinetantennae for operating and optimizing the UMTS network. It iscomposed of one CCU (Central Control Unit) located inside the cabinet

    and other devices located outside the cabinet, one or several RCU(Remote Control Unit),

    The CCU controls one or several RCU. It provides the power for theconnected devices (RCU) and handles alarming.

    The RCU or RCU Slim is a remote controlled motor. It is mounted onthe antenna and adjusts the electrical downtilt angle.

    The RCU can be connected to daisy chain, no need to use a splitter.

    The CCU managed the entire AISG network. It is installed in 9312

    Compact OD user rack. It is connected to node B system to the xCCMumodule (in Compact) via Ethernet 10base T link (Site LAN).

    The CCU is powered by DC -48V through USER ICO. It provides 3RS485 AISG outputs to AISG antenna network via TRDU AISG andcontrol cables.

    Some alarms coming from the CCU are transmitted to the node B via C-USER ICO (User alarms).

    The RET solution proposed only in case of co-localization of 9312Compact OD.

    Other kits constituting the global RET system (TMA AISG, RCU) areordering in ship loose.

    TMA AISG should be used for the RETA solution (+24V)

    The CCU characteristic:

    Power DC -48V, Current max 1.5A

    Figure 10 RETA AISG

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    23/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 21

    April 29, 2009 Method 06-6273

    Preliminary

    4.1.6.4 LP PCM Module

    The LPPCM module is proposed to provide the connection of 8 E1 PCMand their protection against electrical perturbations that could occurbetween the 9312 Compact OD and the customer equipment.

    LPPCM has a function that protects devices from excessive voltage &current caused by power induction, lightning, etc.

    The LPPCM Module consists of one module located on the 1/2 userspace with one line connection through the PCM input and oneequipment connection through the xCCM-u board.

    Figure 11 LPPCM Module Layout

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    24/56

    22 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.1.6.5 IEAM Module

    The External Alarm Module Kit is proposed to provide the connectionof 16 external alarms and 6 remote controls and their protection againstelectrical perturbations that could occur between the 9312 Compact OD

    and the customer equipment.

    The External Alarm Module Kit consists of one module and two digitalcables and one ground cable.

    The External Alarm Module Kit is located in the left hand side of DigitalModules when viewed from the front of the cabinet.

    Figure 12 IEAM Module layout

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    25/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 23

    April 29, 2009 Method 06-6273

    Preliminary

    4.2 9312 Compact OD Power Requirements

    This chapter describe the power characteristics and requirements for9312 Compact OD, currently this 9312 Compact OD is proposed onlyin one variant AC.

    4.2.1 AC Voltage Range

    The 9312 Compact OD outdoor AC only cabinet is powered from oneof the following power supply networks:

    230VAC, single phase, Two wires (Phase, Neutral) and protectiveearth (180/264VAC 22%/+15%)

    120/240VAC, Split phase US, Three wires (Phase 1, Phase 2, Neutral)and protective earth (180/264VAC 22%/+15%)

    The AC power networks shall be TT or TN-S. However, the cabinetshall suffer no irreversible damage when it is wrongfully connected toan IT or TN-C power network.

    The cabinet operate at full performances across the voltage range[180V; 264V] and the frequency range [45Hz; 65Hz].

    4.2.2 AC Consumption of 9312 Compact OD

    Below some examples of power consumptions and battery backup timein function of some configurations (xCEM-u, xCCM-u and TRDU 40W2100Mhz)

    Figure 13 DC Power Consumption and BBUP Time (Compact) with TRDU 40W

    Note: Typical Power consumptions provided assume externaltemperature at 25C, maximum assume in all the temperaturerange

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    26/56

    24 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    In case batteries are charging, the max DC power consumption is1600W with one rectifier or 2000W when the configuration is equippedwith 2 rectifiers, thanks to the input current limitation.

    In case heaters are on (during the cold start up or when temperature islower than 0C and equipment power consumption is lower than 800W),the Max DC power consumption is 800W (cf Environmental coolingsystem chapter).

    The power supply consumption, based on the TRDU output power andsome measurements, is the following (Figures have to be confirmedwith the serial production):

    Figure 14 DC Power Consumption Vs TRDU Output Power

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    27/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 25

    April 29, 2009 Method 06-6273

    Preliminary

    4.3 Site Requirements

    4.3.1 Site Access

    Once a site has been selected, access conditions should be evaluated todetermine whether the cabinet should be delivered populated (easy-access site) or depopulated (difficult-access site).

    The access conditions must comply with cabinet dimensions and theavailable moving equipment.

    The packaging can be removed to get over an obstacle (door orstaircase...) but keep some protection of the 9312 Compact OD(Antistatic bag or vapor barrier or blanket...)

    4.3.1.1 Easy Access Site Characteristics

    The site access conditions allow the mechanical handling of apopulated cabinet throughout the distance separating the deliverypoint from the mounting location without manual carrying.

    The mechanical means used to carry and/or hoist the fully populatedcabinet (e.g. dolly system, elevator, etc) must be qualified to bear thefully populated cabinet weightin compliance with standard securityrequirements.

    4.3.1.2 Difficult Access Site Characteristics

    For this type of site, mechanical means cannot cover the entiredelivery to mounting location distance; part of the way (as small as it

    might be) requires manual carrying. As a consequence, the cabinetcan be depopulated to reduce its weight.

    Even though the cabinet can be carried manually, the maximum useof mechanical means is encouraged to enhance the safety and securityof both staff and equipment.

    4.3.2 Cabinet Handling

    The 9312 Compact OD cabinets are delivered upright with a corrugatedcardboard sleeve on a wooden pallet in case of road transport. They aredelivered lying in plywood crates in case of air and sea transports. In allcases, the specific packing allows their handling by means of a fork-lifttruck.

    The equipment should be unpacked as close as possible to their precisemounting location.

    The path from the delivery point to the mounting location should beclear of any obstacles.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    28/56

    26 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    Note: The Handle Extractor is now classified as a separate tool, and willnot delivered with the node B (3JR08430AA)

    4.3.2.1 Lifting

    The populated cabinet must be handled with mechanical devices(thecabinet may only be guided manually during lift-off or during finalpositioning, provided that basic safety rules are observed by thepersonnel).

    The cabinets are hoisted with 4 lifting eyes M12 type associated with aspacer, by a lifting vehicle suited to the cabinet weight and to the sitecharacteristics (height, jib).

    Note: This equipment should be lifted using 4 (four) lifting ring sets.Four sets but these are NOT delivered with the Node B. (A liftingring set comprises 1 (one) lifting ring 1AD011980007 + 1 (one)spacer 1AD003950005).

    Since the hoisting operation with a lifting vehicle is designed to positionthe cabinet directly on its mounting support, the access conditions of thelifting vehicle are extremely important and obviously, the mountingsupport, if needed, should be installed before hand.

    In case of outdoor hoisting with a jib crane, the parameters to take intoaccount are:

    Floor mechanical resistance.

    Height of the building.

    Width of the building.

    Width of the street.

    Width of pavements / sidewalks.

    Natural obstacles.

    Safety requirements for the hoisting operation.

    All other handling methods must be specified and validated if requiredby the project.

    A specific manual moving by 4 installers (mover profile) or a specificmechanical moving by 2 installers means is needed to install this 9312Compact OD.

    The empty cabinet can be carried by 2 installers (mover profile).

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    29/56

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    30/56

    28 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.3.3 Floor

    The 9312 Compact OD cabinet can be installed either on a concretefloor or on a raised floor.

    The floor covering must be antistatic (about 1MOhms) or the technicianmust use an antistatic bracelet.

    4.3.3.1 Resistance

    In accordance to cabinet weight and door opening, the minimum floor

    resistance should be, AC fully configured: 220 kg/m(only for the 9312Compact OD)

    If needed, a load-spreading structure should be studied in compliancewith the maximum floor resistance allowed by the supporting surface

    and the type of mounting interface chosen to install the cabinets (I-Beams, customer frame...).

    4.3.3.2 Floor Flatness

    The 9312 Compact OD must be installed on a level floor surface. Themaximum tolerance for floor flatness is 5 mm over 2 m(~ 0.2 over78).

    In other words, the vertical tolerance shall not exceed 5 mm over a 2 mhorizontal length.

    If the floor does not respect this maximum tolerance, the cabinet onceinstalled may be twisted and the cabinet door might be impossible toopen. In this case, cabinet watertightness along the front doors shall notbe guaranteed.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    31/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 29

    April 29, 2009 Method 06-6273

    Preliminary

    4.3.4 Pole

    4.3.4.1 Resistance

    The pole with the bracket should support more 300 Kg of load.

    The bracket should be fixed on a pole of diameter 200 mm (8 in) to 600mm (24 in). The bracket are fixed by threaded pin and clamps.

    The 9312 Compact OD should be installed at a height of 170 mm (6.69in) minimum from the floor. But at a height of 500 mm (19.70 in) isrecommended for a comfortable work

    4.3.4.2 Cabinet Securing

    The cabinet are secured on the bracket by 4 screws/bolts.The optionalplinth could be used but is not mandatory.

    4.3.5 Wall

    4.3.5.1 Resistance

    The wall with the bracket should be to support more 300 Kg of load.

    4.3.5.2 Flatness

    The supporting wall must be flat and more or less vertical (maximum tiltof 5 per cent).

    The cabinet can be installed on different types of wall:

    solid wall

    solid wood

    The cabinet should be installed to 170 mm (6.69 in) minimum of heightof the floor. But at a height of 500 mm (19.70 in) is recommended for acomfortable work (man height)

    Depending of wall type, all elements for fixed the bracket on the wallshould be designed by the customer. (Pegs, screws etc..)

    4.3.5.3 Cabinet Securing

    The cabinet are secured on the bracket by 4 screws/bolts. The optionalplinth could be used but is not mandatory.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    32/56

    30 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.3.6 Site Dimensioning Rules

    The criteria governing the size of the site are:

    the cabinet dimensions and the distance constraint,

    the relative positions of cabinets (Site layout),

    cabinets orientation in outdoor site, with respect to exposure to winds/sun and possible nuisance caused to the neighbourhood (noise).

    the input constraint of cables.

    If the site contains more than one cabinet, the dimensions andconstraint must be adapted

    4.3.6.1 Cabinet Dimensions and Distance Constraint

    The clearances considers the clean surface which is the minimum

    surface required to install the cabinets on site. Cabling access bulkheadsare available on the front side of the cabinet.

    The following figures display the minimum surface for a cabinet on siteinstallation.

    Figure 16 9312 Compact OD Cabinet Installation

    700

    580

    1280

    100

    For be able to open the door with 120 angle and with 100mm in frontof it, refer to next Figure 17which give the associated dimensions

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    33/56

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    34/56

    32 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    Figure 18 Minimum Space Required on Site Layout for 2 Compact OD Side by Side

    50 mm

    Figure 19 Minimum Space Required on Site Layout with 2 Compact OD - Back to Back

    580 mm

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    35/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 33

    April 29, 2009 Method 06-6273

    Preliminary

    4.3.6.3 Cabinets Orientation in Outdoor Site

    The cabinet must be placed so that following rules are respected (ifpossible):

    heat dissipation is optimized by placing the cabinet back facing southfor northern-hemisphere countries (the cabinet back should face northfor southern-hemisphere countries).

    rainfall effects are limited by placing the cabinet parallel to thedirection of dominant winds.

    in case of a high-wind area (typhoon...), the cabinet should be placedin a protected zone.

    The local weather conditions must be taken into account to determinethe priority between the rules above.

    Possible nuisance caused to the neighborhood must also be taken intoaccount (noise...).

    4.3.6.4 Input Constraint of Cables

    The positioning of the cabinet must take into account the arrival of thecables to the cabinet.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    36/56

    34 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.4 9312 Compact OD Site Preparation

    This section describes the preparatory work which should be carried outon site prior to the 9312 Compact OD outdoor variant installation.

    4.4.1 9312 Compact OD Support

    The 9312 Compact OD outdoor can be installed on the types of sitesbelow:

    Ground level or terraces of buildings

    The cabinet(s) can be installed on a concrete pad (with its plinth) or onan I-beam structure. In any case, the structure should be able to supportthe cabinet(s) weight(s) and respect the securing holes positioning.

    Figure 20 Floor Solution

    pole or wall mounting with frame support

    A pole or wall mounting bracket can be used by the customer and to bemade with the following constraints:

    - The fixing points of the cabinet

    - The cabinets dimensions (weight and size)

    - Interface and environmental conditions of the cabinet.The pole and wall support the maximum cabinet weight andenvironmental constraints (Snow, wind, ice...).

    It is preferable to install the pole/wall mounting to have the cabinet atthe man heightfor operation purpose.

    The 9312 Compact OD can be fixed on pole from 8"(200 mm) to 24"(600 mm).

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    37/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 35

    April 29, 2009 Method 06-6273

    Preliminary

    Figure 21 Wall or Pole Solution

    Wall

    Pole

    Pole

    The floor, wall, pole mounting kit are provided in an optional ancillarieskit. All external mounting kits should be approved for outdoor use. If themounting kit are not ordered, their characteristics should comply withthe ancillaries definitions, Alcatel-Lucent 9312 Compact OD IRM KitsDefinition. (Plinth is not mandatory of this two case)

    Note: Only for the wall solution the pegs and screws for fixing themounting bracket should be designed by the customer, dependingfrom the wall type.

    4.4.2 Earth Plate

    The earth plate is installed systematically on each site, all the sitegrounding circuits are connected to it:

    Cabinet grounding via a 25 mm(4 AWG) ground copper cable,

    Antenna feeder grounding kits,

    Metallic conduits or cable trays

    Grounding cable from AC box distribution or others.

    This earth plate is installed close to the cable entry of the BTS basecabinets:

    on the terrace,

    in the cable trench.

    It is continuously linked to the earth electrode of site.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    38/56

    36 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    The maximum impedance of the earth electrode measured from theearth plate must be less than 10 Ohms.

    4.4.3 Cable Tray

    The cable tray is dimensioned according to the site configuration (referto Table 6) and must be grounded. It allows:

    The cable routing (AC power, ground cables, feeders...),

    The cable protection (for example to avoid damage possibly causedby ice blocks falling from the top of the mast),

    The rules of separation between light and heavy current cables.

    Table 6 Cable Quantity for one Cabinet 9312 Compact OD

    Items Quantity Type of Signal

    AC Power cable 1 AC Voltage

    PCM Cable Up to 2 PCM

    Ground cable 1 Ground

    RF Cable Up to 6 Radio

    Alarm Cable Up to 2 Alarm

    The connection of all the external cables is done in front lower side ofthe 9312 Compact OD. There are 4 paths (each side of plinth) to route

    the external cables (Floor solution only is mandatory)

    In case the 9312 Compact OD is installed on a pole or wall mountingsupport, the cables must come from below.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    39/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 37

    April 29, 2009 Method 06-6273

    Preliminary

    4.4.3.1 Solution 9312 Compact OD Alone

    Customer AC Box

    The 9312 Compact OD cabinet AC Model is not provided with main

    disconnect device. Therefore, appropriate disconnect device should beprovided as part of the building installation by the customer.

    For a site with several cabinets whatever the cabinet type, onedisconnect device is required for each equipment installed on the site.

    The customer AC box is not provided by Alcatel-Lucent. The locationof the customer AC box must take into account the length of the cablesconnected to the cabinet (

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    40/56

    38 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    Figure 22

    Main site breakerbipolar, D curve

    BTS dedicated 40A breakerbipolar, C curve

    S8000 1st cabinet

    subscription line

    line available for other purpose

    Mains

    S8000 2nd cabinet

    BTS dedicated 40A breakerbipolar, C curve

    BTS dedicated breaker,

    bipolar, C curve

    BTS dedicated breaker,

    bipolar, C curve

    9312 Compact OD

    Second Cabinet

    Main Site Circuit Breaker (Single Phase)

    The global current requirement in operational conditions and worst caseconfigurations for the 9312 Compact OD AC, on a power networksingle phase 220-240 Vac or split phases 208-240 Vac, will not exceed11 Ain steady state (heaters).

    The closest standard circuit breaker dimension is 16A,bipolar, Ccurve.

    The AC cable should be connected on the ground via the metallicallyhardware of customer breaker or other.

    For installation in site of one BTS, a existing kit with AC cable of 25 m

    could be re-used:

    NTQG48 BF: Ens Inst Street AC Sing Cord 25m ROHS version

    NTQG48FF: Ens Inst Street Cord Bi 25m Rohs version

    For installation in site of more BTS a Roll solution could be used:

    3BK25561AAAA AC Power Cable 3x2.5 mm Roll 100m

    No roll for Bi phase cable (type US)

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    41/56

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    42/56

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    43/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 41

    April 29, 2009 Method 06-6273

    Preliminary

    Figure 24 9312 Compact OD Bulkhead

    Above View

    Table 7 Type of 9312 Compact OD Connections

    Terminal Number Type of connector (cabinet side)

    Equipotentiality point 2 (on each side of plinth) M6 (1/4) Stud

    GND 1 1 x M6 (1/4) Stud

    AC Power 1 IP 66 cable gland for an AC cable

    from 15 to 18 mm (0,55 to 0,7 in)

    PCM Cable Up to 2

    RF Connectors 6 7/16 connector type

    4.5.2.2 Ground Cable

    The grounding cable from the cabinet to the site earth plate must be asshort as possible, with a section of at least 25 mm (AWG 4).

    The inter-cabinet ground cables if any routed between 9312 Compact

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    44/56

    42 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    OD and others cabinet colocalised on the same site (for equipotentiality)must be as short as possible, with a section of at least 16 mm (AWG 6).

    For installation in site of one BTS, a existing Ground cable kit of 25 mcould be re-used:

    NTQG48DF: Ens Inst Str/Mono Cord GND 25m ROHS version

    For installation in site of more BTS, a roll solution could be used:

    3BK08957BA: Cable 1x16 mm Y/G Roll 100m

    4.5.2.3 BTS AC Supply Cables

    The mains AC supply cable comes directly from the customer AC boxand is connected directly to the cabinet AC inputs.

    The cables used for powering each BTS cabinet must be able to hold atleast 11.5A for single, split phases configurations,

    They are dimensioned according to the distance between the cabinet andthe customer AC box.The voltage drop due to cable resistance must beso that the voltage at the cabinet level is in the window 180-264 Vac forall AC mains.

    Each power supply cable is composed of conductors (three for singlephase, four for split phases) of the same section as described below.

    Table 8 BTS AC Supply Cables: Single Phase

    Cable type Cable color For example

    Section (mm) Max. length (m)

    4 25

    4 25

    4 25

    Phase Brown

    Neutral Blue

    PE (Protective Earth) Yellow/Green

    Table 9 BTS AC Supply Cables: Split/Dual Phases (Europe wires)

    Cable type Cable color For example

    Section (AWG) Max. length (m)

    L1 Brown 4 25

    L2 Black 4 25

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    45/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 43

    April 29, 2009 Method 06-6273

    Preliminary

    The cable must be flexible and screened, and each conductor must be ofmulti-thread type (to facilitate lug crimping).

    The cables must be waterproofed and must have a section compatiblewith the AC cable gland entry in order to guarantee the IP55 of thecabinet.

    Table 11 External Cable Section for AC Cable Gland Entry

    Mono/Split Phase

    4.5.3 External Cables Marking

    Table 12 External Cables Marking

    Function Labeling

    Cabinet k DC Standard -48V or 0V Cab k DC -48V or 0V

    Cabinet k AC single/split phase L, N, PE / L1, L2, N, PE

    Cabinet k Protective Ground Cab k GND

    Neutral (grounded conductor) Blue 4 25

    Electric ground (grounding

    conductor)

    Yellow/Green 4 25

    Table 10 BTS AC Supply Cables: Split/Dual Phases (US wires)

    Cable type Cable color For example

    Section (AWG) Max. length (m)

    4 25

    4 25

    4 25

    4 25

    L1 Black

    L2 Red

    Neutral (grounded conductor) White

    Electric ground (grounding

    conductor)

    Yellow/Green

    External diameter up to 23 mmTBC

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    46/56

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    47/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 45

    April 29, 2009 Method 06-6273

    Preliminary

    4.5.5 Feeders and Antenna System

    The customer must foresee and install the antennae system and thefeeders. The antennae are installed in compliance with the radioengineering studies by trained staff.

    Feeders are used to establish the RF link between the BTS and theantennae or TMAs. The feeders are in cable tray, near the radio cabinet,ready to be connected. A female 7/16 connector equips each feeder end.

    The feeder interconnections shall comply with outdoor constraints(waterproofing...).

    On the BTS side, the feeders should arrive as close as possible to thecabinet mounting location (the number of feeders depends on theconfiguration type) in order:

    To allow an easier installation: depends on the size of feeder used, itmight be very difficult to position correctly the feeder in front of theRF connector on BTS side.

    To avoid excessive efforts on the RF connector on the BTS side: riskof damage to the connectors.

    To allow easier maintenance operation.

    The Cable used for feeder should have a maximum attenuation of6.99dB/100m at 2300Mhz. Couple connector losses = 0.2dBmax.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    48/56

    46 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.5.6 Lightning Protection

    All the site must be protected against direct lightning strikes. The sitemust be equipped with a lightning conductor on top. For lighteningprotection it is important that the radio lines from the antenna to thecabinet are regularly grounded with grounding kit (see Figure 25).

    The antenna ports of the cabinet can be protected with a gas tube surgearrestor (optional).

    Note: In case TMA is employed, the site should be equipped withspecific surge arrestor as gaz tub in order to avoid short circuitbetween the inner and outer connector of feeder (the TMA issupplied in DC voltage thanks to its RF cables).

    The cabinet also includes a surge arrestor for induced current surge onthe AC Main power supply.

    Figure 25 Grounding Kits on Feeders

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    49/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 47

    April 29, 2009 Method 06-6273

    Preliminary

    4.5.7 Radio Cables Types

    RF Jumpers

    The antenna feeders arrive as close as possible to the BTS cabinet

    mounting location; the interconnection between the feeders and jumpersis done outside.

    The number of feeders depends on the combiner type and on the numberof sectors.

    The feeder interconnections shall comply with outdoor constraints(waterproofing...).

    The radio feeders are coming from the antenna mast. They must beprotected at the ground level by a metallic cable tray (to avoid damagepossibly caused by ice blocks falling from the top of the mast).

    Peculiarities of RF Links

    The RF jumpers are optional. The BTS should be connected to thefeeders via RF jumpers, the minimum bending radius should complywith the space available below the cabinet, in plinth space.

    The jumper connector should be straight, Male, DIN 7/16 for a key 32mm (hexagonal head).

    Table 14 Alcatel-Lucent Jumper RF Code

    Order code Description

    3BK05360CAAA JUMPER 7/16MM LG=2M The Jumper length is site dependent.

    W/o specification, provide 2 meters

    length.

    With TMAprovide 4 jumpers per sec-

    tor on the Antenna side and 2 jumpers

    per sector on the Node B side (see fig

    14)

    W/o TMAprovide 2 jumpers per sector

    on the Antenna side and 2 jumpers per

    sector on the Node B side (see fig 14)

    3BK05360DAAA JUMPER 7/16MM LG=3M

    Standard 2 m max. long jumpers are used to connect the feeders to theBTS.

    For each sector, several antennae can be available (for Main andDiversity reception), the number depending on configuration.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    50/56

    48 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    Connection to the Aerial RF Part

    The use of jumpers on each side of the feeder (BTS/feeder and Feeder/antenna or TMA) is recommended when using LDF or FSJ type offeeder. Example of RF Link with UMTS TMA

    S1 S2 S3

    Cabinet

    MainAntenna

    DivAntenna

    Feeder 7/8" (35m)

    Jumper2 m

    Jumper2 m

    Jumper2 m

    MAIN PATH DIV PATH

    TMATMATMA

    Hatch

    Plate

    Minimum singlebending radius

    125mm

    125mm

    250 mm

    32mm

    50Ohms

    TBC

    TBC

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    51/56

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    52/56

    50 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

    4.6 Final State of Site Preparations

    The site access and layout permits the 9312 Compact OD Physicalinstallation.

    If necessary, a mounting support is installed, grounded.

    The different external interfaces to the equipment (ground plate,Customer AC box(es), cable tray, PCM distribution frame...) areinstalled.

    The following operations have been performed:

    A ground plate is connected to the earth sink.

    The circuit impedance and the continuity are checked and recorded.

    A power supply output is available for each cabinet (breaker off).

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    53/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 51

    April 29, 2009 Method 06-6273

    Preliminary

    5.0 References

    Table 15 Reference Documents

    Document Number Title

    R1 ETS 300 019 -1-4 Environmental Conditions and Environmental

    Tests for Telecommunications Equipment; Part

    1-4: Classification of Environmental Conditions.

    Stationary use at non-weather protected loca-

    tions: class 4.1E except for:

    Low temperature - 40C

    High temperature +55C

    Wind: 200 km/h

    High absolute humidity 36g/m3

    Mechanical condition: 4M3

    R2 IEC 60529 Degree of Protection Provided by Enclosures -

    (IP Codes)

    R3 IEC 721-3-4 Classification of Environmental Conditions

    Partie 3:

    Classification of groups of agents

    environment and their severities

    R4 IEC 721-2-6 Classification of Environmental Conditions.

    Part2 : Environmental Conditions Appearing in

    Nature-Earthquake Vibration and Shock : Level

    3

    R5 ETS 300 019-1-1 Classification of Environmental Conditions Stor-

    age Class 1.2

    R6 ETS 300 019-1-2 Classification of Environmental Conditions

    Transportation Class 2.2

    R7 ETS 300 753 Acoustic Noise Emitted by Telecommunications

    Equipment

    R8 ETS 300 019 -2-3 Classification of environmental conditions

    R9 ETS 300 019 -1-4 Specification of environmental tests Stationary

    use at non-weather protected locations

    R10 Bellcore

    GR487-CORE

    defines Bellcore's requirements for telecom

    equipment to be placed in an outdoor environ-

    ment

    R11 Bellcore

    GR 63-CORE

    Network Equipment - Building System (NEBS)

    requirements. Physical protection.

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    54/56

    Document Number Title

    R12 EN 301 489-1 and

    EN 301 489-23

    Electromagnetic Compatibility and Radio spec-

    trum matters (ERM); Electromagnetic Compati-bility (EMC) standard for Radio equipment and

    services; Part 1: Common technical require-

    ments

    R13 CFR 47 Part 15 Class B Radio frequency devices

    R14 ICES 03 Digital Apparatus Issue 3, Nov. 22, 1997

    R15 3GPP TS 25.113 Technical specification group radio access net-

    works. Base Station Electro Magnetic Compati-

    bility Ed V3.5.0

    R16 PE/DCL/DD/XXXXX BTS compact OD Engineering Rules

    R17 IEC 364 Electrical Installation of buildings

    R18 IEC 721-3-3 Classification of groups of environmental

    parameters and their severity. Stationary use at

    weather protected locations: classe3

    R19 UL 1950

    CSA C22.2 950

    IEC 60950

    Safety of information technology equipment

    including electrical business equipment

    52 /Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification

    Method 06-6273 April 29, 2009

    Preliminary

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    55/56

    Alcatel-Lucent 9312 Compact Node B Outdoor Site Specification / 53

    April 29, 2009 Method 06-6273

    Preliminary

    6.0 Appendices

    6.1 Abbreviations

    A ampere

    AC Alternating Current

    AWG American Wire Gauge

    BTS Base Station Transceiver Subsystem

    DC Direct Current

    DF Distribution Frame

    DDM Dual Duplexer Module

    E1 Standard European PCM system

    uCECU Universal Compact Environmental Control Unit

    EMC Electro-Magnetic Compatibility

    EMI Electro-Magnetic Interference

    GND GrouND

    IP Ingress Protection

    RF Radio Frequency

    T1 Standard US PCM system

  • 8/11/2019 9312 Compact OD Site Specification Apr09

    56/56

    Method 06-6273 April 29, 2009

    Preliminary

    6.2 Terms

    Depopulated:Cabinet partially equipped.

    Difficult access site:For this type of site, mechanical means cannot coverthe entire delivery truck to mounting location distance. Part of the way (assmall it might be) requires manual carrying.

    Easy access site:No manual carrying is required to set the populated cabinetonto its mounting location.

    Optimized operational temperature range:The temperature rangeprevailing in most populated areas of the world. Temperature above andbelow this range, fall into areas of low non-existent population, or into thecategory of one time only recorded extremes.

    Populated:Fully equipped cabinet.

    Total operational temperature range:The BTS will perform at bothextreme temperatures, however:

    at low extremes, the electrical supply requirements of the BTS siteincreases.

    at high extreme, for more than 5 hours per day and for more than 72hours per year may result in early failure of temperature dependentmodules and/or components. The sound power by the BTS increases by0.5 bels per 5C rise above the optimized temperature high extreme.

    End of Document