INSTALLATION INSTRUCTIONS FOR PART 99-9101

86-9001 Head Unit Removal Keys I Flat Blade Screwdriver I File

1-800-221-0932 www.metraonline.com

KIT FEAT U R E S

© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION

APPLICATIONS

2000-2003 Audi A6

• DIN Head Unit Provisions with Pocket• Stacked-DIN Head Unit Provisions

A) Radio Housing I B) Pocket

KIT COMPONENTS

TOOLS REQUIRED:

99-9101

AB

99-9101

• Dash Disassembly- 2000-2003 Audi A6 ------------------------------------------------ 1

•Kit Assembly- DIN Head Unit Provision with Pocket ---------------------------- 2- Stacked DIN Head Unit Provisions -------------------------------- 3

•Final Assembly ------------------------------------------------------ 4

•Notes ----------------------------------------------------------------- 5

99-9101

1

2000-2003 Audi A6

Disconnect the negative battery terminalto prevent an accidental short circuit.

Insert Metra’s 86-9001 into the slots inthe factory head unit and pull the unit out.

Figure A

1

2

Disconnect the wiring.3

File down the dash cavity about 1/8 inchin the 4 locations pictured.

Figure B

4

A

B

99-9101

2

DIN Head Unit Provision with Pocket

1 Slide the DIN cage into the RadioHousing and secure by bendingthe metal locking tabs down.

Figure A

2 Slide the after-market head unitinto the cage and secure.

Figure B

3 Snap the pocket into the RadioHousing until secure.

Figure C

A

B

C

99-9101

3

STACKED DIN HEAD UNIT PROVISIONS

1 Slide the DIN cages into the RadioHousing and secure by bending themetal locking tabs down.

2 Slide the after-market DIN headunits into the cages until secure.

4

FINAL ASSEMBLY1 Locate the factory wiring harness in the dash and make the connection as shown.

Metra recomends using the proper mating adapter and making the connections asshown. (Isolate and individually tape off the ends of any unused wires to preventelectrical short circuit.)

2 Re-connect the negative battery terminal and test the unit for proper operation.3 Reassemble radio and dash assemblies in reverse order of disassembly.

A

A) Strip wire ends back 1/2"B) Twist ends togetherC) SolderD) Tape

B

C

D

99-9101 FINAL ASSEMBLY

Make wiring connections using the EIA color code chart shown below and the instructions included with the headunit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individuallytape off ends of any unused wires to prevent electrical short circuit.

12V Ignition / Acc . . . Red12V Batt / Memory . . YellowGround . . . . . . . . . . . Black*Power Antenna . . . . . BlueAmp Turn-On . . . . . . Blue / WhiteAmp Ground . . . . . . . Black / WhiteIllumination. . . . . . . . OrangeDimmer . . . . . . . . . . Orange / White

Right Front (+) . . . . . GrayRight Front (-) . . . . . . Gray / BlackLeft Front (+) . . . . . . WhiteLeft Front (-) . . . . . . . White / BlackRight Rear (+). . . . . . VioletRight Rear (-) . . . . . . Violet / BlackLeft Rear (+). . . . . . . GreenLeft Rear (-) . . . . . . . Green / Black

*NOTE: When Black a wire is not present, ground radio to vehicle chassis.All colors may not be present on all leads due to manufacturer’s specifications.

METRA / EIA WIRING CODE

FINAL WIRING CONNECTIONS

99-9101

5

INST999101

1-800-221-0932 www.metraonline.com© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION