a+ server 4042g-6rf/trf quick reference guide · cpu2 p2-1a p2-2a p2-3a p2-4a 16 dimms cpu1 p1-1a...

1
http://www.supermicro.com MNL-1528-QRG Board Layout A+ Server 4042G-6RF/TRF Quick Reference Guide Storage Module CPU Installation Beep Codes Front View & Interface Heatsink Installation 1. Place heatsink on top of installed CPU 2. Line up the two screws to socket 3. Push down heatsink and screw down as shown 4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten each screw, to avoid damaging the system MEMORY Caution SAFETY INFORMATION IMPORTANT: See installation instructions and safety warning before connecting system to power supply. http://www.supermicro.com/about/policies/safety_information.cfm WARNING: To reduce risk of electric shock/damage to equipment, disconnect power from server by disconnecting all power cords from electrical outlets. If any CPU socket empty, install protective plastic CPU cap CAUTION: Always be sure all power supplies for this system have the same power output. If mixed power supplies are installed, the system will not operate. For more information go to : http://www.supermicro.com/support ! ! ! Top View of DDR3 Slot Release Tab Release Tab Note: Notch should align with the receptive key point on the slot. Notch Notch Front View Attach the barcode label as illustrated BIOS Beep Codes Beep Code/LED Message Description 1 beep Refresh Circuits have been reset. (Ready to power up) 5 short beeps + 1 long beep Memory 1 long beeps + 8 short beeps Video Video adapter disabled or missing No memory detected 20 19 18 17 16 6 Note 1: Due to OS limitations, some operating systems may not show more than 4 GB of memory. Note 2: Due to memory allocation to system devices, the amount of memory that remains available for operational use will be reduced when 4 GB of RAM is used. The reduction in memory availability is disproportional. JL1 JI2C2 JI2C1 LE1 JWF1 Battery JPUSB1 JWOL1 3-SGPIO1 3-SGPIO2 COM2 JBT1 UIO PCI-E 2.0 X8 SATA0 SATA1 SATA2 SATA3 SATA4 SATA5 SAS1 SAS0 SAS3 SAS2 SAS4 SAS5 SAS7 SAS6 CPU1 CPU3 CPU4 CPU2 P2-DIMM1A P2-DIMM1B P2-DIMM2A P2-DIMM2B P2-DIMM3A P2-DIMM3B P2-DIMM4A P2-DIMM4B P1-DIMM4A P1-DIMM3B P1-DIMM3A P1-DIMM2B P1-DIMM2A P1-DIMM1B P1-DIMM1A P4-DIMM1B P4-DIMM2A P4-DIMM2B P4-DIMM3A P4-DIMM3B P4-DIMM4A P4-DIMM4B P4-DIMM1A P3-DIMM4B P3-DIMM4A P3-DIMM3B P3-DIMM3A P3-DIMM2B P3-DIMM2A P3-DIMM1B P3-DIMM1A UID SLOT1 PCI-E 2.0 X8 SLOT2 PCI-E 2.0 X16 SLOT3 PCI-E 2.0 X8 SLOT4 PCI-E 2.0 X16 P1-DIMM4B BMC Intel 82576 AMD SP5100 AMD SR5690 4 1 2 3 5 7 8 9 10 11 12 13 14 15 25 24 23 22 21 26 27 28 29 Description No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 UIOP PCI-E 2.0 x8 Slot1 PCI-E 2.0 x8 Slot2 PCI-E 2.0 x16 Slot3 PCI-E 2.0 x8 Slot4 PCI-E 2.0 x16 CPU1 P1-DIMM4A/P1-DIMM4B P1-DIMM3A/P1-DIMM3B P1-DIMM2A/P1-DIMM2B P1-DIMM1A/P1-DIMM1B CPU3 P3-DIMM4A/P3-DIMM4B P3-DIMM3A/P3-DIMM3B P3-DIMM2A/P3-DIMM2B P3-DIMM1A/P3-DIMM1B Description No. 16 17 18 19 20 21 22 23 24 25 26 27 28 29 CPU4 P4-DIMM4A/P4-DIMM4B P4-DIMM3A/P4-DIMM3B P4-DIMM2A/P4-DIMM2B P4-DIMM1A/P4-DIMM1B CPU2 P2-DIMM4A/P2-DIMM4B P2-DIMM3A/P2-DIMM3B P2-DIMM2A/P2-DIMM2B P2-DIMM1A/P2-DIMM1B JWF1 = Compact Flash Card Power Connector SAS #0~#3, SAS #4~#7 Ports (H8QG6-F only) SATA0/SATA1/SATA2/SATA3/SATA4/SATA5 JBT1 = CMOS Clear SNK-0043P Heatsink SNK-0042P USB Ports Power Failure LED Information LED LAN1 LED & LAN2 LED Device Activity LED Reset Button Power Button 1 2 3 4 5 6 7 Description No. 2 1 7 4 3 5 6 Storage Module Configuring the Storage Module for 5.25” Devices 1. Remove the 5.25” drive trays from the storage module. 2. Remove the screws and drive tray brackets from the drive trays. 3. Install the 5.25“ devices into storage module. 4. Replace the module back into the chassis. 5. Ensure that the storage module is securely locked into position. Release Lever H8DG6/H8QGi-F Memory Population for Optimal Performance -For a Motherboard with One CPU (CPU1) Installed # DIMMS CPU Channel 1 Channel 2 Channel 3 Channel 4 4 DIMMs CPU1 P1-1A P1-2A P1-3A P1-4A 8 DIMMs CPU1 P1-1A P1-1B P1-2A P1-2B P1-3A P1-3B P1-4A P1-4B Memory Population for Optimal Performance -For a Motherboard with Two CPUs (CPU1 & CPU2) Installed # DIMMS CPU Channel 1 Channel 2 Channel 3 Channel 4 8 DIMMs CPU1 P1-1A P1-2A P1-3A P1-4A CPU2 P2-1A P2-2A P2-3A P2-4A 16 DIMMs CPU1 P1-1A P1-1B P1-2A P1-2B P1-3A P1-3B P1-4A P1-4B CPU2 P2-1A P2-1B P2-2A P2-2B P2-3A P2-3B P2-4A P2-4B Memory Population for Optimal Performance – For a Motherboard with Four CPUs (CPU1, CPU2, CPU3 & CPU4) Installed # DIMMS CPU Channel 1 Channel 2 Channel 3 Channel 4 16 DIMMs CPU1 P1-1A P1-2A P1-3A P1-4A CPU2 P2-1A P2-2A P2-3A P2-4A CPU3 P3-1A P3-2A P3-3A P3-4A CPU4 P4-1A P4-2A P4-3A P4-4A 32 DIMMs CPU1 P1-1A P1-1B P1-2A P1-2B P1-3A P1-3B P1-4A P1-4B CPU2 P2-1A P2-1B P2-2A P2-2B P2-3A P2-3B P2-4A P2-4B CPU3 P3-1A P3-1B P3-2A P3-2B P3-3A P3-3B P3-4A P3-4B CPU4 P4-1A P4-1B P4-2A P4-2B P4-3A P4-3B P4-4A P4-4B DIMM Module Population Conguration For memory to work properly, follow the tables below for memory installation: Per Channel DIMM Populations Options DIMM Type DIMM A DIMM B Max. MHz, 1.5V DIMMs Max. MHz, 1.35V DIMMs Max. GB/ Channel Unbuffered DIMM SR or DR Empty 1600 MHz 1333 MHz 8 GB B G 8 z H M 0 0 6 1 R S R S B G 6 1 z H M 3 3 3 1 R D R D Registered DIMM SR or DR Empty 1600 MHz 1333 MHz 16 GB B G 6 1 z H M 0 0 6 1 R S R S B G 2 3 z H M 0 0 6 1 R D R D QR Empty 1333 MHz 1066 MHz 32 GB QR QR 1066 MHz 800 MHz 64 GB Load Reduced DIMM B G 2 3 z H M 3 3 3 1 y t p m E R Q B G 4 6 z H M 3 3 3 1 R Q R Q Align CPU to socket; install CPU straight down NOTE: Do not bend pin inside socket ! ÌMNL-1528-QRG$Î

Upload: others

Post on 23-Sep-2020

10 views

Category:

Documents


0 download

TRANSCRIPT

Page 1: A+ Server 4042G-6RF/TRF Quick Reference Guide · CPU2 P2-1A P2-2A P2-3A P2-4A 16 DIMMs CPU1 P1-1A P1-1B P1-2A P1-2B P1-3A P1-3B P1-4A P1-4B CPU2 P2-1 ABP2-2 P2-3 P2-4 P2-4B Memory

http://www.supermicro.com MNL-1528-QRG

Board Layout

A+ Server 4042G-6RF/TRF Quick Reference Guide

Storage Module

CPU Installation

Beep Codes

Front View & Interface

Heatsink Installation

1. Place heatsink on top of installed CPU2. Line up the two screws to socket3. Push down heatsink and screw down as shown 4. NOTE: Only use 6-8 lb/f of torque; otherwise, hand-tighten each screw, to avoid damaging the system

MEMORY

Caution

SAFETY INFORMATIONIMPORTANT: See installation instructions and safety warning before connecting system to power supply.http://www.supermicro.com/about/policies/safety_information.cfm

WARNING: To reduce risk of electric shock/damage to equipment, disconnect power from server by disconnecting all power cords from electrical outlets.If any CPU socket empty, install protective plastic CPU cap

CAUTION: Always be sure all power supplies for this system havethe same power output. If mixed power supplies are installed, the system will not operate.

For more information go to : http://www.supermicro.com/support

!

!

!

Top View of DDR3 Slot

Release Tab Release Tab

Note: Notch should align with the receptive key point on the slot.

Notch Notch

Front View

Attach the barcode label as illustrated

BIOS Beep CodesBeep Code/LED Message Description1 beep Refresh Circuits have been reset.

(Ready to power up)

5 short beeps + 1 long beep

Memory

1 long beeps + 8 short beeps

Video Video adapter disabled or missing

No memory detected

20 19 18 17 16

6

Note 1: Due to OS limitations, some operating systems may not show more than 4 GB of memory.

Note 2: Due to memory allocation to system devices, the amount of memory that remains available for operational use will be reduced when 4 GB of RAM is used. The reduction in memory availability is disproportional.

JL1

JI2C2JI2C1

LE1

JWF1

Battery

JPUSB1

JWOL1

3-SGPIO

13-SG

PIO2

COM

2

JBT1

UIO

PC

I-E 2.0 X

8

SATA0SATA1SATA2SATA3SATA4SATA5

SAS1SAS0

SAS3SAS2

SAS4SAS5

SAS7SAS6

CPU1 CPU3

CPU4CPU2

P2-D

IMM

1A

P2-D

IMM

1B

P2-D

IMM

2A

P2-D

IMM

2B

P2-D

IMM

3A

P2-D

IMM

3B

P2-D

IMM

4A

P2-D

IMM

4B

P1-D

IMM

4A

P1-D

IMM

3B

P1-D

IMM

3A

P1-D

IMM

2B

P1-D

IMM

2A

P1-D

IMM

1B

P1-D

IMM

1A

P4-D

IMM

1B

P4-D

IMM

2A

P4-D

IMM

2B

P4-D

IMM

3A

P4-D

IMM

3B

P4-D

IMM

4A

P4-D

IMM

4B

P4-D

IMM

1A

P3-D

IMM

4B

P3-D

IMM

4A

P3-D

IMM

3B

P3-D

IMM

3A

P3-D

IMM

2B

P3-D

IMM

2A

P3-D

IMM

1B

P3-D

IMM

1A

UID

SLO

T1 PC

I-E 2.0 X

8

SLO

T2 PC

I-E 2.0 X

16

SLO

T3 PC

I-E 2.0 X

8

SLO

T4 PC

I-E 2.0 X

16

P1-D

IMM

4B

BMC Intel82576

AMDSP5100

AMDSR5690

41 2 3 5 7 8 9 10 11 12 13 14 15

25 24 23 22 2126

27

28

29

DescriptionNo.1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

UIOP PCI-E 2.0 x8

Slot1 PCI-E 2.0 x8

Slot2 PCI-E 2.0 x16

Slot3 PCI-E 2.0 x8

Slot4 PCI-E 2.0 x16

CPU1

P1-DIMM4A/P1-DIMM4B

P1-DIMM3A/P1-DIMM3B

P1-DIMM2A/P1-DIMM2B

P1-DIMM1A/P1-DIMM1B

CPU3

P3-DIMM4A/P3-DIMM4B

P3-DIMM3A/P3-DIMM3B

P3-DIMM2A/P3-DIMM2B

P3-DIMM1A/P3-DIMM1B

DescriptionNo.16

17

18

19

20

21

22

23

24

25

26

27

28

29

CPU4

P4-DIMM4A/P4-DIMM4B

P4-DIMM3A/P4-DIMM3B

P4-DIMM2A/P4-DIMM2B

P4-DIMM1A/P4-DIMM1B

CPU2

P2-DIMM4A/P2-DIMM4B

P2-DIMM3A/P2-DIMM3B

P2-DIMM2A/P2-DIMM2B

P2-DIMM1A/P2-DIMM1B

JWF1 = Compact Flash Card Power Connector

SAS #0~#3, SAS #4~#7 Ports (H8QG6-F only)

SATA0/SATA1/SATA2/SATA3/SATA4/SATA5

JBT1 = CMOS Clear

SNK-0043P HeatsinkSNK-0042P

USB Ports

Power Failure LED

Information LED

LAN1 LED & LAN2 LED

Device Activity LED

Reset Button

Power Button

1

2

3

4

5

6

7

DescriptionNo.

2 17 4 356

Storage Module

Configuring the Storage Module for 5.25” Devices

1. Remove the 5.25” drive trays from the storage module.2. Remove the screws and drive tray brackets from the drive trays.3. Install the 5.25“ devices into storage module.4. Replace the module back into the chassis.5. Ensure that the storage module is securely locked into position.

Release Lever

H8DG6/H8QGi-F

Memory Population for Optimal Performance-For a Motherboard with One CPU (CPU1) Installed

# DIMMS CPU Channel 1 Channel 2 Channel 3 Channel 4

4 DIMMs CPU1 P1-1A P1-2A P1-3A P1-4A

8 DIMMs CPU1 P1-1A P1-1B P1-2A P1-2B P1-3A P1-3B P1-4A P1-4B

Memory Population for Optimal Performance-For a Motherboard with Two CPUs (CPU1 & CPU2) Installed

# DIMMS CPU Channel 1 Channel 2 Channel 3 Channel 4

8 DIMMsCPU1 P1-1A P1-2A P1-3A P1-4A

CPU2 P2-1A P2-2A P2-3A P2-4A

16 DIMMsCPU1 P1-1A P1-1B P1-2A P1-2B P1-3A P1-3B P1-4A P1-4B

CPU2 P2-1A P2-1B P2-2A P2-2B P2-3A P2-3B P2-4A P2-4B

Memory Population for Optimal Performance – For a Motherboard with Four CPUs (CPU1, CPU2, CPU3 & CPU4) Installed

# DIMMS CPU Channel 1 Channel 2 Channel 3 Channel 4

16 DIMMs

CPU1 P1-1A P1-2A P1-3A P1-4A

CPU2 P2-1A P2-2A P2-3A P2-4A

CPU3 P3-1A P3-2A P3-3A P3-4A

CPU4 P4-1A P4-2A P4-3A P4-4A

32 DIMMs

CPU1 P1-1A P1-1B P1-2A P1-2B P1-3A P1-3B P1-4A P1-4B

CPU2 P2-1A P2-1B P2-2A P2-2B P2-3A P2-3B P2-4A P2-4B

CPU3 P3-1A P3-1B P3-2A P3-2B P3-3A P3-3B P3-4A P3-4B

CPU4 P4-1A P4-1B P4-2A P4-2B P4-3A P4-3B P4-4A P4-4B

DIMM Module Population Confi gurationFor memory to work properly, follow the tables below for memory installation:

Per Channel DIMM Populations OptionsDIMM Type DIMM A DIMM B Max. MHz,

1.5V DIMMsMax. MHz,

1.35V DIMMsMax. GB/ Channel

Unbuffered DIMM

SR or DR Empty 1600 MHz

1333 MHz

8 GB

BG 8 zHM 0061RS RS

BG 61 zHM 3331RD RD

RegisteredDIMM

SR or DR Empty 1600 MHz

1333 MHz

16 GB

BG 61zHM 0061RS RS

BG 23zHM 0061RD RD

QR Empty 1333 MHz 1066 MHz 32 GB

QR QR 1066 MHz 800 MHz 64 GB

LoadReduced

DIMM

BG 23zHM 3331ytpmERQ

BG 46zHM 3331RQRQ

Align CPU to socket; install CPU straight down

NOTE: Do not bend pin inside socket!

ÌMNL-1528-QRG$Î