aac ventilation control(1)

8/22/2019 AAC Ventilation Control(1)

1/12

Manufactured by:

Rev. 6.17.09

Distributed by:

AAC Ventilation Controls

AAC Blocks Providethe Strength andPerformance toEnsure Safety

This submittal packet includes:

MSHA Accepted: ST30/01aMSHA Accepted: ST30/02MSHA Accepted ST30/00Hebel AAC- MSDSHebel Thin bed Mortar MSDS


2/12

Xella Aircrete North America, Inc.2400 Hebel Boulevard

Adel, GA 31620

877-41-HEBEL www.hebel-usa.com

Manufactured

Rev. 6.1

Easy to Cut

Lightweight

Fire Resistant, Non Combustible

Convenience of Short Stack Packagin

Ease of Constructability

No Need for Dry Storage, MoistureResistant

Short Stack Pallet Sizes:

Tongue and Groove or Standard BlocksThickness 6" or 8"Class AAC-2 or AAC-4AAC Shipping Density 45 pcfBlock Dimensions: 6"x 8"x 24", 6"x 12"x 24"

8"x 8"x 24", 8"x 12"x 24"Dry or Wet StackAny MSHA listed Suitable Sealant

HEBEL AAC (AutoclavedAerated Concrete) provides alightweight solution to easelabor and increaseperformance of ventilationcontrols.

Block: ThxHxL =8.0x 12.0x 24.0Pallet: LxWxH =48.0x 48.0 x 36.036 Blocks / Pallet





3/12


4/12


5/12


6/12


7/12


8/12


9/12

Page 1 of 2

Mater ia l Safe ty Data Sheet

AUTOCLAVED AERATED CONCRETE (AAC)

SE CTION I. PR ODUCT IDENTIFICATION

P r o d u c t N a m e : H E B E L - Autoclaved Aerated Concrete (AAC)

P r o d u c t U s e : Load bearing and non load bearing components for interior and exterior wall,floor and roof slabs.

M a n u f a c t u r e r s I n f o r m a t i o n : X e l l a A i r c r e t e N o r t h A m e r i c a I n c .2400 Hebel BoulevardAdel, Georgia 31620

T e l e p h o n e : 229.896.1593 (Tel)229.896.1912 (Fax)

SE CTION II. HAZARDOUS INGREDIENTS

COMPONENT CA S No. % by Weight OS HA P EL (mg/m3) ACGI H TLV (mg/m

3)

P o r t l a n d C e m e n t 65977-15-1 28 5 10S i l i c a 14808-60-7 50 0.1 0.1L i m e 39445-23-3 12 5 10G y p s u m 7778-18-9 10 5 10E x p a n d i n g A g e n t PA TENT ED 0.1 - 0.15 -- --

SE CTION III. PHYSIC AL DATA

Boiling P oint : N/A S pecific Gravity: 0.5-0.7Vapor P ressure: N/A Evaporation Rate: N/AVapor Density (Air=1): N/A Melting P oint: N/AS olubility in Water (%wt) N/A Volatiles (by vol.): N/ApH: 9.0-10.5 VO Cs (g/lt) N/AAppearance and odor: White solid with no odor

SE CTION IV. FIRE AND EXP LOSION HAZARDS

Flash P oint : N/AFlammability (LE L,HE L) N/AHazardous combustion products: NoneUnusual fire and explosion hazards: NoneS pecial F irefighting procedures: The applicable for surrounding materials and substances

SE CTION V. REACT IVITY DATA

Stability: StableCo nditions to avoid: NoneIncompatible materials: None, this is an inert material

Hazardous decomposition products: NoneHazardous polymerization: Will not occur

SE CTION VI. HEALTH HAZARD DATA

EFFECTS OF ACUTE OVEREXP OSURE:No ac ute effects are related to the use of this product.

EFFECTS OF CHRONIC OVEREXP OSURE:Long-term overexposure to high concentrations of dust without the use of a dust mask may reduce respiratoryfunction in some individuals.


10/12

Page 2 of 2

INHALATION:When cutting the material, dust particles are generated. R espiratory tract must be protected. Irritation of noseand upper respiratory tract, shortness of breath. P rolonged inhalation of excessive s ilica dus t may reduce lungfunction.

E Y E S :No s pecific health hazards are related to this route of exposure. When cutting the material, eyes must beprotected against dust generated.

SK IN:Handling may cause dry skin. A void contact to skin.

ING ES TI ON : Not applicable under normal use. May result in obstruction and temporary irritation of thedigestive tract if large quantities are cons umed.

MEDICAL CONDITIONS AGGRAVATEDBY EXP OSURE:Unknown

SE CTION VII. FIRST AID MEASURE S INHALATION:Re move to fresh air. If persis tent irritation, se vere coughing, or breathing difficulty occurs s eek medicalattention.

EYE CONTACT:

Re move contact lenses. Fl ush eyes, i ncluding under eyelids, with large amounts of water for 15 minutes.If i rritation persis ts, see k medical attention.

SK IN CONTACT:Wash affected areas with soap and water. If irritation persists seek medical attention.

INGESTION:May result in obstruction if ingested. S eek medical attention.

SECTION VII I. SP ECIAL P ROTECTIONRESP IRATORY PROTECTION:Dust mask must be worn for dust generating operations.

PROTECTIVE GLOVES:

As recommended for cons truction operations.

EYE PROTECTION:Use of protective safety glasses or goggles is recommended for dust generating operations.

SECTION IX. ADDITIONAL INFORMATION

AA C dust contains crystalline silica which has been evaluated as Group 2A (probably carcinogenic to humans) bythe International Agency for Research on Cancer (IARC).

WASTE DISPOSAL:F ollow the above safety instructions, coll ect waste and dust by sweeping or vacuuming and place in containers.Dispos e of containers and waste according to local, state or federal regulations.

The in formation conta ined in thi s material S afety Da ta S heet is beli eved to be reli ab le . No guarantee is impli edor expressed regarding the accuracy of this information or the use of the product since the conditions of use arebeyond manufacturers control. N othing contained herein should be construed as a recommendation to use thisproduct in conflict with existing patents c overing any material or its use.

This MS DS was generated from in formatio n avai lable of components of thi s product. I t compl ies with minimumrequirements stated by OSHA as defined in Section G, 29CFR1910.1200.MS DS date of preparation: 04/19/07


11/12

Material Safety Data Sheet

ELITE BUILDING PRODUCTS, INC. 4235 Buford Highway Duluth, Georgia 30096 (678) 206-0242 fax (678) 206-0254

II. Hazardous Ingredients

Material CAS No. OSHA PEL: mg/m3 ACGIH TLV mg/m3

Portland Cement 65977-15-1 5 10

Silica 14808-60-7 0.1 0.1

Vinyl 1216-01 5 10

III. Health Hazard Data

Routes of Hazard

Exposure Determination

Inhalation

Basis for Determination

Contains Silica*

* Prolonged inhalation of excessive silica dust may

reduce lung function.Effects of Acute Overexposure No acute effects.

Effects of Chronic Overexposure Long term overexposure to high concentrations of thisdust without the use of a dust mask may reduce

respiratory function in some individuals.

Medical Condition Aggravated by Exposure Unknown

Eyes and Skin No special precautions. Flush with water for 15 minutes.

Inhalation and Ingestion No special precautions.

I. Product Identification

Product Name Hebel Thinbed Mortar Manufacturers Name

Phone (678) 206-0242

Elite Building Products, Inc.4235 Buford HighwayDuluth, GA 30096

IV. Physical Data

Boiling Point N/A pH 12

Vapor Pressure N/A Specific Gravity 2.8

Vapor Density N/A Melting Point N/A

Solubility in Water Negligible Evaporation Rate N/A

Appearance and Odor Whiteish


12/12

V. Fire and Explosion Data

Flash Point None Special Fire Fighting Procedures None

Flammable Limits in Air N/A Unusual Fire and Explosion Hazard None

Auto Ignition Temperature None

VI. Reactivity Data

Conditions Contributing to Instability Reacts with acids to liberate CO2

Conditions Contributing to Hazardous Polymerization None

Hazardous Decomposition Products None

VII. Disposal, Spill, or Leak Procedures

Waste Disposal Method Material is not classified as a hazardous waste under RCRA Section 3001. Usenormal solid waste disposal procedures which are in compliance with Federal,

State and Local Regulations.

Spill or Leak Procedures Material is not classified as a toxic pollutant or a hazardous substance underSection 307 and 311 of the Clean Water Act. Accidental releases can be

cleaned up by sweeping, vacuuming, or flushing with water.

Neutralizing Chemicals None required.

VIII. Special Protection Information

Ventilation Use sufficient general area ventilation. Local exhaust may benecessary where Threshold Limit Values (TLVs) are exceeded or

dusty conditions exists.

Personal Protective Equipment

Eyes Recommended

Gloves Recommended

Other None

Respiratory Protection For dusty conditions use a dust mask approved by NIOAH.

ELITE BUILDING PRODUCTS, INC. 4235 Buford Highway Duluth, Georgia 30096 (678) 206-0242 fax (678) 206-0254

The information contained in this Material Safety Data Sheet is believed to be reliable. No guarantee is implied or expressedregarding the accuracy of this information or the use of the product since the conditions for use are beyond our control. Nothingcontained herein should be construed as a recommendation to use this product in conflict with existing patents covering any

material or its use.

aac ventilation control(1)

Documents