about the emb-312 t-27 tucano - juniaer.com.brjuniaer.com.br/gallery/t27_50cc_brochure.pdf · the...
TRANSCRIPT
About the EMB-312 T-27 Tucano
Projected in 1978 under Joseph Kovacs direction by Embraer, the EMB-312 is a single turbo prop engine basic
trainer powered by Pratt & Whitney Canada PT6A-25C turning a HARTZEL three blade prop , low wing with two
MB ejection seats. The EMB-312 was christened “Tucano” an exotic brazilian bird by a cadet.
Designated as T-27 (or AT-27 for light attack version) by FAB (Brazilian Air Force) 168 units were delivered. The
6 first aircraft equipped EDA (Air Demonstration Squadron AKA Smoke Squadron) in September 1983.
The T-27 Tucano was a great success at the international market , offering a cockpit with instruments displayed
in a very similar way to modern fighters with low operational cost. More than 800 units were sold to many
countries as Argentina , France , Iraq , Paraguay , Peru , Venezuela , Egypt and others. It was made under license
by Egypt and England in a different version named “Shorts Tucano”.
At FAB the Tucano is used by AFA (First Air Instruction Squadron at Air Force Academy) , and was used by many
other squadrons including Fighter Groups , Observation , Defense but the main highlights always shined at EDA
Squadron , the Air Demonstration Squadron , eagle’s nest of proud and high skilled pilots.
Engine: Pratt&Whitney Canada PT6A-25C , 750shp Wingspan: 11,14m (438,58”)
Lenght: 9,86m (388.19”) Height: 3,40m (133.86”)
Wing Area: 19,4m2 (30070,06 in²) Weight: 1810Kg (3990,36 lb) (Empty)
Maximum Speed: 457Km/h (283,97 mph) 3175Kg (6999,67 lb) (Maximum)
EDA 1 Painting Scheme , from EDA (Esquadrão de Demonstrações Aéreas-Air Demonstration Squadron)
1983 to 2000
EDA 2 Painting Scheme , from EDA (Esquadrão de Demonstrações Aéreas-Air Demonstration Squadron)
2001 to 2013
EDA 3 Painting Scheme , from EDA (Esquadrão de Demonstrações Aéreas-Air Demonstration Squadron)
2015 to nowadays *This painting scheme is used at the EMB-314 A-29 Super Tucano aircraft.We offer this
painting scheme at the T-27 Tucano 50cc , but it is not used in any full size T-27.
Flat Gray Camuflage Painting Scheme , Light ground attack units.
AFA Painting Scheme , (Air Force Academy)
AFA 30 Years Commemorative Painting Scheme.
Flat 3 Colours Camouflage Painting Scheme. Light ground attack unit , with or without shark mouth.
Vinicius is the 2018 Brazilian Scale champion in Sport category with his T-27 Tucano 50cc
Dino Digiorgio flew his way at Top Gun 2017 to an impressive fifth place in X-Class !!!
An innovative model airplane in the popular 50cc class! High level detailing and flight performance that
will surely surprise modelers and lovers of this legendary airplane.
This is the T-27 Tucano 50cc ARF Juniaer, ready for retracts installation, with scale flaps, fantastic
finishing and available with many painting schemes, very realistic, all embossed details, with rivets,
antennas, opening side door with installed hinge and lock, panel divisions, compartments, pitot tube replica,
landing gear doors, cockpit with instruments panels and clear canopy. Engine cowl in two parts with exhaust
replicas.
Made of high quality epoxy resin with structural reinforcements, low weight and high resistance due to
the high technology FULL COMPOSITE vacuum lamination tecnique. Wing and stabilizers with aluminum
tubes (1 tube in the wing and 1 at stabilizer), laminated with fiberglass and epoxy resin and carbon fiber
reinforcements with laser cut plywood structures. Clear plastic canopy, epoxy resin canopy frame, epoxy
resin cockpit with instruments panels. Ailerons, flaps and elevators factory hinged with perfect alignment.
Rudder to be installed with hinge-points provided with the kit. Servo trays and tank tray in laser cut
plywood. Finished in automotive paint, scale stickers applied and PU clear coated for long lasting fuel
resistant life.
Very stable flight characteristics, realistic and acrobatic. Capable of many scale manouvers such as rolls,
slow rolls, cuban eights, knife edge, lancevacks, inverted flight and much more you can imagine.
There´s a TURBO PROP version available just out of the oven! For King Tech KT-45TP !
If you are interested, please contact us!
DOES NOT INCLUDE ASSEMBLY ACCESSORIES such as linkages, fuel tank, retracts, wheels, engine,
spinner, propeller, radio and electronic equipment, etc...
Specifications:
Wingspan: 2300mm (90.55 inches) Lenght: 2050mm (80.71 inches) Wing Area: 84,63 dm2 (1311 in2)
Weight: 10 to 12 Kg (22 lb to 26.50 lb) (flying weight, depending on the installed accessories/equipment)
Radio: 7 channels minimum for limited installation – 9 or more channels for full installation (not included)
Servos: All servos must be metal gears, standard size (not included)
7 servos of 10Kg (22 lb) or more torque (2 ailerons, 2 flaps and 2 elevators and 1 rudder)
Suggestions: SAVOX: SAVSC0251MG FUTABA: S3305MG, S3306MG SPEKTRUM: SPMSA6150
3 servos of 5Kg (11 lb) or more torque (1 throttle, 1 choke and 1 pneumatic retracts)
Suggestions: SAVOX: SAVSC0254MG, SAVSC0253MG, SAVSC0252MG SPEKTRUM:SPMSA6180
Engine: 50 to 60cc gas burning 2 cycle engine (we recommend DLE-55RA for a perfect installation with
original mounts and muffler) Fuel Tank: 24oz ou larger Suggestion: Dubro DUBR 424
Electric: GPMG 4800 RIMFIRE 50cc Great Planes MAX50 ROTOMAX 50cc Turnigy
Distance between firewall and prop washer 171mm (6.73 in) (lenght)
Distance between engine center line and end of engine head: 125mm (4.92 in) (height)
Spinner: 3 ½” aluminum
Propeller: 22x10 two blade or 20x10 three blade (or according to your engine’s manual recommendations)
Aluminum Tubes: * optional carbon fiber tubes are available separately
1 aluminum wing tube at wing (25,40mm external diameter x 1,58mm thickness x 885mm lenght)
1 1 aluminum wing tube at stabilizer (12,70mm x 1mm x 340mm)
C.G. point is at 130mm (5.11 Inches) from the leading edge , measured at the wing root. Wing chord is
453mm (17.83 inches). To check the balance hold your airplane in the inverted position by the wing root at
the indicated C.G. point , without fuel. Retracts must be retracted. The airplane must present a light nose
weight tendency. Never hold your model airplane by the wing tips only! Always hold it by wing roots
(closer to the fuselage). Never take off your model airplane without checking the balance! If there is a
tail weight tendency you must add weight to the front of the model airplane until the balance is correct. A
model airplane with tail weight tendency will not fly as it should ! It can cause serious accidents and damage
to people and properties around the flying area which Juniaer is hold harmless.
Linkage , Horns and Hard Points:
The model airplane has high wood structural reinforcements for control horns installation at the ailerons,
flaps, elevators and rudder. These points are 40mm x 40mm (15.75 inches x 15.75 inches), positioned at
strategic places and must be followed right as the instructions below, under risk of loosing control causing
damage and risks to people and properties around the flying area. If you wish to modify or adapt equipments
that requires modifications on the original project never do that by your own, please get in touch to Juniaer
customer service to verify the possibility of installation.
Ailerons: 2 simple horns are needed, 25mm to 35mm (1 1/8” to 1 ¼”) tall. Servo arms (20mm to 25mm) (1”
from center to the end) must be positioned to the wing root side. Note that both sides of the wing has the
same positioning. The horn hard point is centered with servo arm slot. Distance between center of control
arm and control horn (in neutral position): 92mm (3.62 inches). Servos must be installed in hard wood
blocks glued with epoxy at the servo tray cover.
Flaps: 2 simple horns needed , 25mm to 35mm (1 1/8” to 1 ¼”) tall. Servo arms (20mm to 25mm) (1” from
center to the end) must be positioned to the wing root side at one side and to the wing tip at other side, as it
comes from factory. The horn hard point is centered with servo arm slot. Distance between center of control
arm and control horn (in neutral position): 85mm to 90mm (3 3/8” to 3 ½”inches). Servos must be installed
in hard wood blocks glued with epoxy at the servo tray cover.
Elevators: : 2 simple horns needed , 25mm to 35mm (1 1/8” to 1 ¼”) tall. Servo arms (15mm to 20mm)
(5/8” to 13/16” from center to the end). The horn hard points are centered with pushrods exits from the
fuselage, and from the root side of the elevators (closer to the fuselage). Servos must be installed inside the
fuselage at the servos tray provided, positioned in parallel and with servo arms to the same side. Acting is
made by 2 fiberglass pushrods and 4-40 treaded rods.
Rudder: 1 dual horn needed (command to both sides) total lenght beetween 100mm to 120mm (4” to 4 ¾”).
Dual servo arm (command to both sides) total lenght beetween 40mm to 45mm (5/8” to 13/16”). The horn
hard points are centered with pull-pull exits from the fuselage. Servo must be installed inside the fuselage at
the servos tray provided, acting with pull-pull cables.
*All control horns must be Heavy Duty and indicated to ¼” scale models airplanes, or giant scale model
airplanes
*All servo arms must be Heavy Duty and indicated to ¼” scale models airplanes, or giant scale model
airplanes
*All rods must be steel made, 4-40 tread or more.
*All links e servo conectors must be Heavy Duty and indicated to ¼” scale models airplanes, or giant scale
model airplanes
Control Surfaces Recommended Defletions:
Ailerons: Beetween 25mm (1”) (low rate) to 35mm (1 7/16”) (high rate) – up and down
Elevators: Beetween 16mm (5/8”) (low rate) to 24mm (1”) (high rate) – up and down
Rudder: Beetween 40mm (1 5/8”) (low rate) to 50mm (2”) (high rate) – left and right
Flaps: Beetween 0º to 10º for take off (we recommend 1º) and beetween 25º to 30º for landing
Retracts Installation: (105º at front gear and 85º at main gears)
Suggestions:
Robart pneumatics:
ROBQ 636RS Main 85º retracts ROBQ 640HDRS 105º front gear
ROBQ 671R e ROBQ 671L Main robostruts ROBQ 674 Front fork robostrut
ROBQ 157VRX Air kit De Luxe large ROBQ 190 Quick connectors ROBQ 169 air lines
Low cost Hobby King (not for scale):
225000021 All Metal Servoless 90 Degree Retract for Large Models (10~12kg)
9225000026-0 All Metal Servoless 90 Degree Steering Nose Retract for Large Models (10-12kg)
344000023 Alloy Oleo Legs Offset Zero Style 50cc Class 2pc
9107000310-0 Alloy Straight Oleo Strut with Swinging Arm 145mm (1pc)
344000046 Scale Jet/Warbird Alloy Wheel 90mm w/Grooved Rubber Tire/Ballraced (2pc)
344000042 Scale Jet/Warbird Alloy Wheel 70mm w/Grooved Rubber Tire/Ballraced (2pc)
Scale navigation lights, with direct receiver connection, universal plug. Turns on and off by radio channel.
Circuit with protection filter for using with RC systems without interference. High intensity LED´s Type 3U
20000mcd. Power: independent battery (7,4V to 12V). Consumption: 500ma Modulation: Works with all
RC systems available. Blinking sequence as the full scale airplane. 1 green led and 1 red led at the wing
tips, 2 strobos at the wing tips, 3 landing lights (2 at the wing and 1 at front retract), 1 red blinking led
and 1 strobo for rudder. Custom shaped to wing tips assembly ready to install.
Dimensions: Main board: 50x32mm (2” x 1 ¼”) Wing Tip Assembly: 35x20mm (3/8” x ¾”)
Web Site: www.juniaer.com.br e-mail: [email protected]
www.facebook.com/asaseases.juniaer Cell Phones: (55) 19 99551-9373(Whatsapp)
www.instagram.com/juniaermodelismo/ (55) 35 9149-8548 (Whatsapp)
You Tube: www.youtube.com/channel/UCQ70OA13XdHJiqXFCOUoL_A Search: juniaer modelismo