ace062_reese_2012_o.pdf (2.44 mb)
TRANSCRIPT
This presentation does not contain any proprietary, confidential, or otherwise restricted information
A MultiAir / MultiFuel Approach to Enhancing Engine System Efficiency
Chrysler (PI): DOE Technology Development Manager:
DOE NETL Project Officer:
ACE062
May 18, 2012 2012 DOE Vehicle Technologies Program Annual Merit Review and Peer Evaluation Meeting, Arlington, Virginia
Ronald A. Reese, II Ken Howden Ralph Nine
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Overview
2
Budget • Total: $29,992,676
– Partner Cost Share: $15,534,104 – DOE Cost Share: $14,458,572
Barriers • Downsized engines offer higher fuel
economy, but the degree of downsizing is limited by transient performance and dynamic range
• For gasoline engines, abnormal combustion (knock) limits the geometric compression ratio, thereby limiting engine efficiency
• EGR improves engine efficiency, but increases in EGR (and efficiency) are limited by combustion instability
• Engine operation in vehicle is not at its most efficient (ideal) state
Timeline • Project Start Date: May 07, 2010 • Project End Date: April 30, 2013 • Percent Complete: 40%
Partners • Argonne National Laboratory • Bosch • Delphi • The Ohio State University
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Project Objectives
• Demonstrate a 25% improvement in combined City FTP and Highway fuel economy for the Chrysler minivan
– The baseline (reference) powertrain is the 2009 MY state-of-the-art gasoline port fuel-injected 4.0L V6 equipped with the 6-speed 62TE transmission
– This fuel economy improvement is intended to be demonstrated while maintaining comparable vehicle performance to the reference engine
– The tailpipe emissions goal for this demonstration is Tier 2, Bin 2
• Accelerate the development of highly efficient engine and powertrain systems for light-duty vehicles, while meeting future emissions standards
• Create and retain jobs in support of the American Recovery and Reinvestment Act of 2009
• Project content is aimed directly at the listed barriers
3
Relevance
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Technology Approach & Contribution
4
Approach
Base Engine Design
& Controls
Low Lock-up Speed
Ideal Engine Operation
Thermal Management
Engine Efficiency
Reduced Losses
Engine Speed, increasing →
Eng
ine
Torq
ue, i
ncre
asin
g →
Low
C
F
S
B
High
Ideal OperationFTP Operation
High compression
ratio
Engine downsizing, and 2-stage
boosting
Cooled EGR, DI, and spray bore
liners for improved knock
resistance
Advanced ignition for improved
stability with high dilution
Goal ≥ 25% Improvement in Fuel Economy
45%
21%
16%
10% 8%
DMP 3SP
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Timeline and Major Milestones
5
Month/Year Milestone or Go/No-Go Decision 1 Completed – November 2010 Performance Specs / Engine Selection
2 Completed – July 2011 Dyno Engine Design Complete
3 Completed – November 2011 Procure, Build & Initial Test of Dyno Engine Complete
4 June 2012 Go/No Go – Dual Fuel for Vehicle Engine
5 August 2012 Design Refinement & Procurement Complete – Vehicle Engine
6 December 2012 Vehicle Level Controls Complete
7 March 2013 Engine Calibration Complete
8 April 2013 Vehicle Demonstration
Approach
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Base Engine Design
6
• Production-style analyses using CFD and FEA were performed to determine design and material selection on critical components
• High Cycle Fatigue (HCF) FEA analysis of the cylinder head shows very good safety factors for a peak cylinder pressure of 180 bar
• Engine design was completed for every engine component (3-D Catia files / 2-D prints), and all parts were procured
Accomplishment/Progress
Three (3) engines were assembled and
are on test, two at Chrysler () and one at Argonne National
Lab ()
HCF Safety Factors for MAMF (goal ≥1.5)
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Combustion Controls
• Dyno engine control system has been completed, and incorporates:
– Chrysler controller master – Bosch GDI slave controller – Bosch diesel slave controller – Delphi combustion feedback controller
• Controls development progress: – GT Power model used as plant model in
co-simulation with Matlab Simulink control system to develop boost control system algorithm
– Developed closed loop control of Cooled EGR (CEGR)
– Investigating behavior of dual fuel system in response to actuator set points to support algorithm development
7
Accomplishment/Progress
Coordinated by
INTECRIO Rapid
Prototype Controller
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Combustion Approach
• Combustion system designed to tolerate high rate of EGR with good combustion stability
– Very high charge motion intake port and chamber – High energy ignition system, dual path using two engines:
• Diesel injector for Diesel Micro Pilot (DMP) ignition at medium to high load, and two spark plugs per cylinder for light to medium load, with 13:1 compression ratio
• Three spark plugs per cylinder, 11:1 compression ratio – 3 valves per cylinder to provide packaging room for spark
plugs and injectors
8
Approach
• Prevent knock to enable a high geometric compression ratio with good combustion phasing
– Cooled EGR – Spray Bore Liner – Gasoline Direct Injection
• Boosted using two turbochargers – Series sequential arrangement for improved transient response and boost
throughout the engine speed range
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Dyno Engine Results – Dual Fuel Engine
• At 13:1 CR, robust DMP combustion is key to meeting full load goal • DMP extends load range, improves burn rate and combustion phasing • Fuel consumption is at goal at low to mid load, within 5% at high load • Switching between SI and DMP modes is problematic
Accomplishment/Progress
9
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Dual Fuel Combustion (1 of 2)
• Controlling the engine over a wide speed/load range while running Diesel Micro Pilot ignition is extraordinarily complicated
• Everything that impacts in cylinder pressure, temperature, and chemistry impacts combustion phasing:
• Argonne National Laboratory is collaborating with Chrysler to better understand DMP combustion through a combination of experimental and computational activities
• Dual fuel decision date is June for the vehicle engine – Decision Criteria: Fuel consumption improvement is compelling
Emissions penalty is small Automatic steady state and transient control is robust
– EGR rate – Intake manifold pressure – Intake manifold charge temperature – Intake cam position – Exhaust cam position
– Diesel injection pressure – Diesel injection timing – Diesel injection quantity – Coolant temperature
Approach
10
This presentation does not contain any proprietary, confidential, or otherwise restricted information
• Combustion modeling at Argonne National Laboratory (ANL)
– 3D software evaluation was completed, selection was made, and software was procured and installed at Chrysler and ANL
– Simulation plan has been developed, and ANL contract is in place (work started 3/2012)
– Computational Resources: • 2 simulation specialists • 240 solver cores from TRACC cluster
– Used to explore actuator control to determine lowest fuel consumption strategy and help establish control strategy and algorithm, with GT Power providing the boundary conditions
– Injector spray tests in APS to validate spray models
– Simulation results will be compared to in-cylinder imaging from dyno engine at ANL
Combustion Simulation Results: DMP Ignition > 2000 K Iso-Temperature Volume
2000 rpm / 12 bar BMEP
Accomplishment/Progress
11
Dual Fuel Combustion (2 of 2)
Example of Initial DMP Results
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Dyno Engine Results – Single Fuel Engine
• Single fuel engine (with 3 spark plugs) has a lower CR than the dual fuel engine • Fuel consumption within 3% of goal at 2000 rpm • Combustion stability (IMEP COV) is better than goal
Accomplishment/Progress
12
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Combustion Feedback and Control
• Delphi Ion-Sense combustion feedback – Delphi Ion-Sense-Enabled High Energy Ignition Coil
Technology successfully used to extract ion current signature from the combustion process, including during dual fuel operation on Proof-of-Concept engine
– Algorithms developed to process the ion current signature into derived combustion phasing parameters; standard deviation for 50% MFB correlation is less that 2 degrees
– Integration of Delphi controller into dyno cell arrangement complete, and communication of Delphi controller with Chrysler Engine Control Unit verified
• Dyno engine includes production-type cylinder pressure sensor which could be used with Delphi controller if necessary
• Engine control strategy under development to incorporate combustion phasing, combustion stability, and knock feedback into Chrysler engine controls
13
Accomplishment/Progress
This presentation does not contain any proprietary, confidential, or otherwise restricted information
2nd Order Mitigation
14
Reduction in 2nd Order Torsional Vibration at Full Load
New crankshaft significantly reduces
torsional vibration
Accomplishment/Progress
• 2nd order mitigation is an enabler for lower torque converter lock-up speeds, and higher engine efficiency
• A Proof-of-Concept pendulum absorber crankshaft (shown) was built and tested in a surrogate vehicle
• Testing of the surrogate vehicle showed a significant reduction in 2nd order crankshaft vibration (see graph), closely matching the prediction
• Other NVH issues were discovered and are being addressed with design improvements
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Engine Speed (rpm)
BM
EP
(bar
)
1000 1500 2000 2500 3000 3500 40000
2
4
6
8
10
12
14
16
18
20
200
250
300
350
400
450
500
550
600
Approaching Ideal Engine Operation
15
Accomplishment/Progress
• 9-speed transmission replaces 6-speed transmission (9 speed transmission development not funded by this project)
• Higher ratio range, and lower ratio steps of 9-speed allows engine to operate closer to the ideal state (minimum fuel consumption for a desired power request)
Reduction in engine operation in the
inefficient area, far from the ideal operation line
B S F C
Bet
ter
6 speed 9 speed Ideal Operation
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Thermal Management System (TMS)
16
Fluid Temperature Benefit On Surrogate Vehicle and Powertrain
No TMS = Baseline With TMS = 3.0% MPG improvement
FTP City+Hwy Time (min)
Approach & Accomplishment/Progress
No TMS (baseline) With TMS
coolant
eng. oil
trans. oil
• Approach – Higher steady state temperatures of
fluids reduces friction losses – Faster warm-up of engine & transmission
improves mechanical efficiency – Dual mode coolant pump is used for
improved efficiency and control • Electric drive flow on demand • Mech. drive efficiency @ hi speed
• Accomplishments – Thermal management system evaluated
on surrogate vehicle • Demonstrated %FE improvement • Validated thermal prediction model • Validated thermal function of controls
model (from OSU) – Coolant circuit flow stand built / tested to:
• Develop coolant pump control strategy
• Validate 1D fluid circuit model
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Reduced Losses (Fuel Shut Off, Stop/Start & Ancillary Load Reduction)
17
Accomplishment/Progress
• Fuel Shut Off - Software created & operational with 9-speed transmission • Stop/Start - Software interface for 9-speed transmission defined
– Hardware and interfaces defined for Stop/Start
• Enhanced Voltage Regulation (EVR) algorithm strategy prototyped – Closed loop control of charging parameters – Opportunistic control algorithm for deciding when to charge (and when not to) – Will be integrated into overarching control scheme being developed by OSU, which
manages the ancillary loads in the most efficient way possible
• EVR + Stop/Start – Delay charging the battery (energy payback for the stop/start event) until there is a
more efficient time to charge – Significantly improves the cycle fuels savings, as opposed to charging the battery
immediately after start
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Controls for TMS and Reduced Losses
18
Thermal Management
System
Accomplishment/Progress
• OSU developed a comprehensive Vehicle Energy Simulator (VES) tool to analyze vehicle ancillary loads and thermal system components
– Predicts energy utilization/consumption for each of the main vehicle subsystems – Provides vehicle fuel economy prediction for a given driving schedule
• VES verified and being used to develop control system architecture and algorithms
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Partnerships / Collaborations
19
Providing computational fluid dynamics (CFD) modeling, spray measurements, and in-cylinder combustion high-speed imaging
to support combustion development and control
Supplied fuel injectors, lines, pumps, harnesses and controllers for the DI gasoline and DI diesel fuel systems, and collaborated
with Chrysler to integrate the injector drivers
Supplied Ion Sense coils and developing combustion feedback system to allow closed loop combustion control
Developed Vehicle Energy Simulation (VES) and developing supervisory controller (Vehicle Energy Manager – VEM) that
oversees and integrates energy management of vehicle subsystems
Accomplishment/Progress
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Future Work / Summary
• Future Work – Complete dynamometer engine testing and model correlation – Refine engine design as required to best meet all functional objectives
• Based upon correlated models and a review of lessons learned from current design/test efforts
– Determine engine type (i.e. single or dual fuel) for vehicle engine – Complete development and implementation of engine control system – Build demonstration vehicles and start emissions testing
• Summary – Engine design is complete, part procured, engines built and on test – Current modeling and proof-of-concept testing support meeting the 25% fuel
economy improvement using the defined technologies – Challenges exist to effectively control the various technologies to optimize the impact
of each in an operating engine – The focus for the remainder of the project will be to develop the operational
strategies and controls to maximize the efficiency of the hardware at hand
20
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Thank You.
21
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Technical Back-Up Slides
22
This presentation does not contain any proprietary, confidential, or otherwise restricted information 23
Argonne National Laboratory Spray Measurements
This presentation does not contain any proprietary, confidential, or otherwise restricted information
Emissions
• Emissions control approach: – Stoichiometric operation over entire speed/load range – Three way catalyst – Cold Start Strategy:
• Secondary air • Investigate expansion stroke injection during secondary air injection • Turbo control valves open on cold start
24
Approach