adapting beer recipes between breweries hryclik
TRANSCRIPT
Adapting Beer Recipes Between Breweries
Kevin Hryclik
Discussion points: Ingredients – What variability can you allow, if any, between
sites?Brewhouse – Where are the potential variables between
operations?Fermentation – Considerations for vessel types and yeast
strains.Aging and Filtration – What are the critical processes?Beer Style considerations – which are the most challenging?Sensory – What are the program considerations to help you
achieve good product match between multiple breweries?
Ingredients
WaterTypically water is adjusted to give a consistent
calcium concentration. This is achieved through the use of calcium chloride or calcium sulphate additions. Calcium will affect malt enzymes & yeast performance.
In regions with extreme water hardness ion exchange systems can be utilized.
Alkalinity may also play a role depending on the yeast strain; this is typically controlled via acidification of brewing water.
IngredientsMalt
6 row vs 2 row malt blendsSome brewers use a blend of 6 row and 2 row malts in
their brewing recipes.Historically this was done to increase the overall
enzymatic activity level since 6 row typically contributed a higher enzyme level than 2 row malt.
2 row malts have improved in terms of enzyme levels and the need to include 6 row is not required from a enzyme level perspective.
The blend requirements today are more driven by economics; recipe matches can be achieved with 100% 2 row malts vs. a blend of 2 row and 6 row malt.
IngredientsAdjuncts
If a recipe has a % of the extract derived from an adjunct such as corn or rice you will want to maintain this ratio vs. trying to match using a 100% malt derived extract source.
Corn grits vs. maltose (brewer’s blend) syrups can be used inter-changably. The decision to use which one is based on the equipment set up at the brewery (cereal cooker capability) and by economics.
Care must be used in determining the syrup type. Some yeast strains may be more susceptible to incomplete fermentations if high dextrose syrups are used. The yeast’s ability to bring in maltose for fermentation can be inhibited if dextrose (glucose) levels are high.
IngredientsHops
2 main considerations are the bittering and aroma hops
Bittering hops should be inter-changeable. One will just have to adjust the amount to compensate for alpha acid content differences and boiling extraction differences.
Aroma hops must not be changed since they are an integral component of the finished beer flavour. Adjustments on the timing of the aroma hop addition may be required due to the different kettle boiling characteristics. This may vary from 15 min before strike out right up to addition at strike out.
Brewing VesselsMash MixerCapabilities of mashing in with water addition at
the same time (voremashing) vs. all water in first & malt dropped in on top, will have an effect on the wetting of the ground malt. More time at protein rest will be required if no voremasher is in use.
Different vessel configurations and heating surfaces will give varying rates of rise during the heating phases. Compensation for conversion will be required for both the rest temperature and time of rest.
Kettles – boiling systems
Kettles – boiling systems
Brewing VesselsKettleMany different kettle boiling systems exist. These
include percs, coils, internal & external calandrias.Boils need to achieve similar vigour and evaporation
rates to give consistency.Modifications to the steam feed will need to be
reviewed to best match boiling characteristics.Other considerations may be required such as open or
closed door boiling.As mentioned earlier, timing of the aroma hop addition
may have to be altered to achieve the best product match.
Fermenter Configuration2 main types of fermentation vessels are in use
today, horizontal and conical bottom vertical fermenters.
Adjustments in the main fermentation temperature at the initial phase of the fermentation may need to be adjusted to provide a flavour match to compensate for the type of vessel in use. The rate of fermentation can have an affect on the formation of flavour components such as esters and sulphur.
Timing for cooling on after the diacetyl reduction phase may need to be adjusted.
Yeast Collection• The yeast strain being used may perform differently
depending on vessel type. Yeast return ratios can be affected.
Yeast Strain Selection
Some beer types are very dependent on the yeast strain due to the flavours contributed by yeast during fermentation.
The decision on using alternate yeast strains can only be determined through trials and sensory evaluation.
Aging
Good process control is required moving into aging to prevent off flavours from arising.
If centrifuges are being used, ensure these are operated with proper programing and controls in place to minimize oxygen pick up.
Establish consistent venting procedures on tank fillings and have a targeted CO2 carbonation levels so consistent aromatic compounds are achieved.
FiltrationEnsure best practices are in place to protect
the beer as it is processed to bright beer.These would include: line packing with low
dissolved oxygen water, CO2 purging of pre-coat and body feed tanks.
The use of low dissolved oxygen water for the final alcohol adjustment (preferably added post filtration).
Beer Style Considerations• What type of beer are you trying to make in
multiple brewing sites?• Is the brand profile a subtle & light flavour or
a robust, heavy flavour?• Your lighter brands will be the greater
challenge.
Sensory Program RequirementsTo achieve product match from multiple
brewing sites you need a disciplined sensory program.
Program requirements include: Trained Sensory Panelists that have knowledge
of flavour attribute and defect intensity training.
Understand how to describe and rate the flavour intensity in beers.
Develop a brand “True to Profile” map that describes the beer using product attributes and intensity levels. A beer should be mapped by highlighting the 7 to 10 main flavour characteristics of the beer.
Intensity Scale & Descriptors:
Brand “True to Profile” Map
Sensory Panels:Exchange samples between production sites
on a weekly basis.Conduct “True to Profile” panels and give an
overall rating for the beer.The panel scores will tell you if you are
achieving a commercial match on the brand between multiple brewing sites.
Provide feedback to production sites on how their beer is performing and if there are particular trends being noted from the sensory panelists.
SummaryMany factors can be
involved in matching beer recipes between brewing sites.
This will be influenced by the beer type, the yeast strain used, raw material selection and equipment designs.
You need to be aware of the factors that you must match and ones you have some ability to vary.