addendum to mr. robot - pitsco...mr. robot now ships with ev3 and a newer-style wireless controller...
TRANSCRIPT
EV3 Addendum to Mr. Robot I
Addendum to Mr. RobotAddendum to Mr. Robot build instructions on how to attach the new LEGO EV3 programmable brick to Mr. Robot.
• The LEGO® NXT Brick has been replaced by the EV3 Brick. Mr. Robot now ships with EV3 and a newer-style wireless controller and sensor module. The controller is a wireless Sony PlayStation® 2 gamepad and can connect to EV3 through a specialized sensor included in your kit.
• Your EV3 is preprogrammed to work out of the box. No additional programming is necessary. Simply connect the wireless controller sensor module to Port 2. The wireless controller and receiver will need to be paired. Follow the instructions in this addendum to pair your controller and receiver.
• The attachment of the EV3 Brick is very simple and is shown in this addendum. Steps throughout the original build instructions show how to attach the NXT Brick; however, those can be ignored. Instead, please refer to the views in this addendum to attach the EV3.
• NXT touch sensors shown in the instructions are no longer compatible with the EV3 system. Any steps shown in the build instructions relating to mounting of sensors can be skipped.
• The program to operate Mr. Robot is preinstalled on the EV3 Brick. Find and run the program Mr. Robot to begin using.
II EV3 Addendum to Mr. Robot
PSP-Nx-v4 Connectivity Guide
Trouble Shooting PSP-Nx-v4 and Joystick ConnectivityThis procedure assumes DreamGEAR MagnaForce Joystick. If you have a different joystick, the details may vary.
Before you begin this procedure, ensure that you have downloaded and reviewed the User Guide from following location:
http://mindsensors.com/pdfs/PSP-Nx-v4-User-Guide.pdf
Ensure that you have inserted batteries in the Joystick. And the power switch on your joystick is in ON position. Adjacent picture will show you the location of the power switch.Adjacent picture shows how to connect PSP-Nx-v4 to the receiver. Ensure that the receiver is engaged in correct orientation, and is fully inserted in the PSP-Nx-v4 socket.
PSP-Nx-v4 light
Connect PSP-Nx-v4 to NXT and connect the Receiver to PSP-Nx. Power on the NXT/EV3 (do not run any program yet). A blinking Blue light on PSP-Nx means, the receiver is not connected properly to PSP-Nx. If the receiver is connected properly to PSP-Nx, and NXT/EV3 is powered ON (without running any program), PSP-Nx will have no lights. Adjacent picture shows location of the light on PSP-Nx-v4.
EV3 Addendum to Mr. Robot III
PSP-Nx-v4 Connectivity Guide
Joystick Light
Blinking Joystick light means the Joystick has not found a Receiver.
If this happens, ensure that:
• Receiver is connected to PSP-Nx-v3.
• PSP-Nx-v3 is connected to NXT, and
• NXT is powered on.Connectivity between Joystick and Receiver
Red oval light button on Receiver.
A blinking button means the receiver is not properly connected to your Joystick.
Power off and on your Joystick and press this button to reset connection between the Joystick and receiver.Set the Joystick in Analog mode.
Press the Analog button on your Joystick once to set it in Analog mode.
IV EV3 Addendum to Mr. Robot
View 1
Partial assembly should look like this.
Parts Needed
8xSocket Head Cap Screw
6-32 x 5/16" 390984x
LEGO® 2x4 Angle Beam4x
LEGO® 3x5 Angle Beam
40xLEGO® Connector
Peg W_Friction
8xLEGO® 3M
Connector Peg W_Friction
4xTETRIX® Hard Point Connector 39120
1xLEGO® MINDSTORMS® EV3
Intelligent Brick
2xLEGO® Beam 15M
2xLEGO® Beam 13M
8xKep Nut 39094
EV3 Addendum to Mr. Robot V
Step 1.0
Step 1.1
VI EV3 Addendum to Mr. Robot
Step 1.2
Step 1.3
EV3 Addendum to Mr. Robot VII
Step 1.4
Step 1.5
VIII EV3 Addendum to Mr. Robot
Step 1.6
Step 1.7
EV3 Addendum to Mr. Robot IX
Step 1.8
Step 1.9
X EV3 Addendum to Mr. Robot
Step 1.10
Step 1.11
EV3 Addendum to Mr. Robot XI
Finished Assembly
XII EV3 Addendum to Mr. Robot
View 2
Finished assembly should look like this.
Parts Needed
2xLEGO®
Connection Peg w Axle
1xMindsensors PSP Sensor with Jack
1xPS2 Dongle
EV3 Addendum to Mr. Robot XIII
Step 2.0
Step 2.1
XIV EV3 Addendum to Mr. Robot
Step 2.2
Finished Assembly