additional safety rules for lawn...
TRANSCRIPT
Motor: 1000WInput: 220-240V ~ 50HzNo load speed: 3600/minCutting Diameter: 300mmCutting Heights: 20mm, 40mm, 60mmCapacity of catcher: 28 LitreWeight (tool only): 7.0kg
1. Start/stop lever2. Upper handle3. Handle securing set4. Catcher flap5. Lower handle6. Wheels
7. Wheel hub8. Lower handle securing point9. Grass catcher10. Cord clips11. Lock-off button
2
SPECIFICATIONS - MODEL NO. ELM-300
KNOW YOUR PRODUCT
3
2
10
11
4
5
1
7
6
8
9
3
TABLE OF CONTENTS
SPECIFICATIONS ………………………………………..
INTRODUCTION…………………………………………
ELECTRICAL SAFETY…………….………………………
GENERAL SAFETY WARNINGS…………………………
ADDITIONAL SAFETY RULES FOR LAWN MOWERS….
ASSEMBLY………………………………………………..
OPERATION………………………………………………
MAINTENANCE…………….……………………………
SPARE PARTS …………….……………………………...
DESCRIPTION OF SYMBOLS ………………………….
PACK CONTENTS ………………………………………
WARRANTY………………………………………………
Page 2
Page 4
Page 4
Page 5
Page 7
Page 9
Page 12
Page 14
Page 15
Page 15
Page 16
Page 18
INTRODUCTION
4
Congratulations on purchasing an Ozito Electric Mower.We aim to provide quality tools at an affordable price.
We hope you will enjoy using this tool for many years.Your Electric Mower ELM-300 has been designed forsmall to medium size lawns and is intended for DIY use only.
SAFETY INSTRUCTIONS
WARNING! When using mains-powered tools, basic safety precautionsincluding the following should always be followed to reduce risk of fire,electric shock, personal injury and material damage.
Read the whole manual carefully and make sure you know how to switch the tooloff, in an emergency, before operating the tool.
Save these instructions and other documents supplied with this machine for future reference.
Read the whole manual carefully and make sure you know how to switch the tooloff, in an emergency, before operating the tool.
Save these instructions and other documents supplied with this machine for future reference.
The electric motor has been designed for one voltage only. Always check that thepower supply corresponds to the voltage on the rating plate.
This tool is double insulated in accordance with AS/NZS 60335-1; thereforeno earth wire is required. If the supply cord is damaged, it must be replaced by an electrician or a power tool repairer in order to avoid a hazard.
1. Before use, examine cord for damage; replace it if there are signs of damageor ageing.
2. Do not use the lawn mower if the electric cables are damaged or worn.
3. Immediately disconnect from the mains electricity supply if the cord is cut, orthe insulation is damaged. Do not touch the electric cord until the electricitysupply has been disconnected. Do not repair a cut or damaged cord; replaceit with a new one.
4. Your extension lead must be unwound, coiled leads can overheat and reducethe efficiency of your mower.
ELECTRICAL SAFETY
!!
!!
!!
5
1. This appliance is not intended for use by young children or infirmed personsunless they have been adequately supervised by a responsible person to ensurethat they can use the appliance safely.
2. Only use the lawn mower in the manner and for the functions described in these instructions.
3. Never operate the lawn mower when you are tired, ill or under the influence ofdrugs, alcohol or medicine.
4. The operator or user is responsible for accidents or hazards occurring to otherpeople or their property.
5. Use the lawn mower only in daylight or good artificial light.
6. Avoid operating your lawn mower in wet grass, where feasible.
7. Take care in wet grass, you may loose your footing.
8. On slopes be extra careful of your footing and wear non-slip footwear.
9. Mow across the face of slopes, never up and down.
10. Exercise extreme caution when changing direction on slopes. Walk never run.
11. Mowing on banks and slopes can be dangerous. Do not mow on banks or steep slopes.
12. Do not walk backwards when mowing, you could trip.
13. Never cut grass by pulling the mower towards you.
14. Switch off before pushing the mower over surfaces other than grass.
15. Never operate the lawn mower with damaged guards or without guards in place.
ELECTRICAL SAFETY (cont.)!!
5. Keep lead away from lawn mower; always work away from the power pointmowing up and down never in circles.
6. Do not pull lead around sharp objects.
7. Always switch off at the mains before disconnecting any plug, cord or extension lead.
8. Never carry the product by the cord.
9. Never pull on the cord to disconnect any of the plugs.
10. Use only AC mains supply voltage shown on the product rating label.
11. It is recommended that the appliance should by supplied via a residual currentdevice (RCD) with a tripping current of not more than 30 mA.
12. Use at least a 10 Amp rated 1.0 mm2 extension cord with a maximum of 25meters and the cord shall be not lighter than:
- If rubber insulated, ordinary tough rubber sheathed flexible cord (code designation 60245 IEC 53);
- If polyvinyl chloride insulated, ordinary polyvinyl chloride sheathed flexible cord (code designation 60227 IEC 53).
GENERAL!!
6
GENERAL (cont.)!!
16. Keep hands and feet away from the blade at all times and especially whenswitching on the motor.
17. Young children should be supervised to ensure that they do not play with the appliance.
18. No one is to operate this appliance without reading and understanding theseoperating instructions.
19. Do not tilt the lawn mower when the motor is running, except when starting orstopping. In this case, do not tilt more than absolutely necessary and lift onlythe part which is away from the operator. Always ensure that both hands are inthe operating position before returning the appliance to the ground.
20. Do not put hands near the grass discharge chute.
21. Never pick up or carry a mower when it is operating or still connected to themains supply.
22. Remove the plug from the mains:
- before leaving the mower unattended for any period
- before clearing a blockage
- before checking, cleaning or working on the appliance
- if you hit an object. Do not use your lawn mower until you are sure that the entire lawn mower is in a safe operating condition
- if the lawn mower starts to vibrate abnormally. Check immediately.Excessive vibration can cause injury.
7
ADDITIONAL SAFETY RULES FOR LAWN MOWERS!!
!! WARNING! If not used properly this lawn mower can be dangerous! Thislawn mower can cause serious injury to the operator and others, the warningsand safety instructions must be followed to ensure reasonable safety andefficiency in using this lawn mower. The operator is responsible for followingthe warning and safety and instructions in this manual and on the lawn mower.Never use the mower unless the catcher or guards provided by themanufacturer are in the correct position.
1) Training
• Read the instructions carefully. Be familiar with the controls and the proper use ofthe appliance.
• Never allow children or people unfamiliar with these instructions to use theappliance. Local regulations may restrict the age of the operator.
• Never mow while people, especially children, or pets are nearby.
• The operator or user is responsible for accidents or hazards occurring to otherpeople or their property.
2) Preparation
• While mowing, always wear substantial footwear and long trousers.
• Do not operate the appliance when barefoot or wearing open sandals.
• Thoroughly inspect the area where the appliance is to be used and remove allstones, sticks, wires, bones, and other foreign objects.
• Before using, always visually inspect to see that the blades, blade bolts and cutterassembly are not worn or damaged. Replace worn or damaged blades and bolts insets to preserve balance.
• On multi-bladed appliances, take care as rotating one blade can cause otherblades to rotate.
3) Operation
• Mow only in daylight or in good artificial light.
• Avoid operating the appliance in wet grass, where feasible.
• Always be sure of your footing on slopes.
• Walk, never run.
• For wheeled rotary mowers, mow across the face of slopes, never up and down.
• Exercise extreme caution when changing direction on slopes.
• Do not mow excessively steep slopes.
• Use extreme caution when reversing or pulling the appliance towards you.
• Stop the blade(s) if the appliance has to be tilted for transportation when crossingsurfaces other than grass, and when transporting the appliance to and from thearea to be mowed.
• Never operate the appliance with defective guards or shields, or without safetydevices, for example deflectors and/or grass catchers, in place.
8
ADDITIONAL SAFETY RULES FOR LAWN MOWERS (cont.)!!
• Switch on the motor according to instructions and with feet well away fromthe blade(s).
• Do not tilt the appliance when switching on the motor, except if theappliance has to be tilted for starting. In this case, do not tilt it more thanabsolutely necessary and lift only the part which is away from the operator.Always ensure that both hands are in the operating position before returningthe appliance to the ground.
• Do not put hands or feet near or under rotating parts. For rotary mowers,keep clear of the discharge opening at all times.
• Never pick up or carry an appliance while the motor is running.
• Pull the plug from the socket:
- whenever you leave the machine;
- before clearing a blockage;
- before checking, cleaning or working on the appliance;
- after striking a foreign object. Inspect the appliance for damage and make repairs as necessary;
- if the appliance starts to vibrate abnormally (check immediately).
4) Maintenance and storage
• Keep all nuts, bolts, and screws tight to be sure the appliance is in safe working condition.
• Check the grass catcher frequently for wear or deterioration.
• Replace worn or damaged parts for safety.
• For cylinder mowers, be careful during adjustment of the appliance toprevent entrapment of the fingers between moving blades and fixed parts ofthe appliance.
9
Fitting the Wheels
1. Remove the body of the lawn mower from thepackaging and place on a flat surface (Fig. 1).
The cutting height of the mower is determined by screwing the wheels in at therequired height (Fig. 2).
2. To fit both back and front wheels to the mower rotate the black hubs within thewheel clockwise into the mower housing at the required height position (1, 2 or 3)(Fig. 2 & 3). All wheelsmust be assembled atthe same height andensure all wheels aretightly secured.
Note: Fit all four wheels at the same height so that the cutting blade runs parallelto the lawn.
Fitting the Lower Handles to the Mover Body
1. Insert the lower handle (5) into the two holes in the lower handle securing point (8)of the mower body. The screw holes in the lower handle (5) should face outwards.
2. Fit the screws (supplied) through the hole above therear wheel, align with the hole in the lower handle (5)and secure into place using a Phillips headscrewdriver (Fig. 4). Repeat for the hole on theopposite side of the mower.
ASSEMBLY
Fig. 1
Fig. 2 Fig. 3
Fig. 4
123
Fitting the Upper Handle to the Lower Handles
1. When you fit the upper handle (2) onto the lowerhandle you can decide the height of the handleby selecting the appropriate fastening hole on thelower handle (5). Align the upper handle (2) usingeither the lower position or higher position (Fig. 5).
2. Place the upper handle (2) over the upper ends of the lower handles. Fit the bolts through theinner side of the lower handle (5) and thenthrough the holes in the upper handle (2). Securein place by screwing the handle securing knobsover the protruding ends of the bolts (Fig. 6).
Securing the Power Cord to the Handle (Fig. 7)
1. Secure the power cord running from the switchhousing to the body of the mower by using thetwo cord clips (10) (supplied). Fit one closer to themower body end of the handle, ensure a littleslack is left between the clip and where the cordenters the mower housing. Fit the other cord clip(10) to the lower end of the upper handle (2).
Assembling the Grass Catcher
1. Assemble the two halves of the grass catcher (9)together. The two halves are identical. Align thetwo halves and push each individual plastic luginto its opposite location. Ensure that all theplastic lugs engage correctly together around theentire middle section (Fig. 8).
2. Assemble the grass catcher handle onto the opening on the top of the grasscatcher (9). The handle will click into position when aligned and fitted correctly.
10
ASSEMBLY (cont.)
Fig. 5
Fig. 6
Fig. 7
Fig. 8
Higher positionLower position
Fitting and removing the grass catcher
The catcher must be attached to the two hooks on themower (Fig. 9).
1. Lift up the catcher flap (4) with one hand and guidethe catcher (9) with your other hand over the twohooks on the mower housing (Fig. 10).
2. Lower the grass catcher (9) and allow it to sit inplace. Lower the catcher flap (4).
3. To empty the grass catcher (9), lift the catcher flap(4) with one hand then lift the grass catcher (9) withthe other hand up off the two raised housing clips.
WARNING! When assembling the grass catcher (9) back to the mower afteremptying, always ensure there is no build up of grass in the grass chute. Ifneeding to clear the grass, always ensure the mower is disconnected from thepower supply prior to clearing. A build up of grass in the grass chute mayprevent grass from moving into the grass catcher effectively.
Using the Cord Retainer
The cord retainer prevents the extension cord frombeing disconnected during use.
1. Make a loop with the extension cord (socket end of cord) and push it through the square hole underthe start/stop lever (1) and secure over the hook.
2. Once fitted, connect the lawn mower power pluginto the extension cord socket as shown in the diagram.
11
ASSEMBLY (cont.)
Fig. 10
Fig. 9
!!
12
PREPARATION
1. While using your lawn mower always wear substantial footwear and long trousers.
2. Make sure the lawn is clear of sticks, stones, wire and debris; they could bethrown by the blade.
3. Before using the lawn mower and after any impact, check for signs of wear ordamage and repair as necessary.
4. Replace a worn or damaged blade together with the blade bolt to preserve balance.
Switching On/Off
To prevent accidental start up of the motor the mower is fitted with a dual actionswitch. To start, press the lock-off button (11) and pull the start/stop lever (1). Themotor automatically stops upon releasing the start/stop lever (1).
WARNING! The blade will coast after the switch has been released. Be aware of the necessary time it takes for the blade to stop coasting. Do not attempt to stop the blade.
1. For the best results, mow the outside edge of the lawn in a clockwise direction first.
2. Then start mowing the edge of the lawn nearest to the power point so the lead islaid out on the lawn you have already cut.
3. For best grass collection, always mow in a straight line; do not swing the lawnmower from side to side.
Do Not Overload the Mower
Mowing long thick grass may cause the motor speed to drop; you will hear achange in the motor sound. If the motor speed drops you may overload your lawnmower, which may cause damage. When mowing in long thick grass first cut withthe cutting height set in the highest position, this will help reduce the load.
ALWAYS HANDLE THE BLADE WITH CARE – SHARP EDGES COULD CAUSESERIOUS INJURY. USE GLOVES.
!!
OPERATION
WARNING! Disconnect the mower from the power supply and ensure theblade has stopped coasting before adjusting the height.
The cutting height of the mower is determined by screwing the wheels in at therequired height. All wheels must be assembled at the same height position.
1. To loosen rotate the black hub within the wheel anti-clockwise. This will release theaxle, remove the hub with wheel.
2. To re-fit in position 1, 2 or 3 to suit the required cutting height, rotate the black hubwithin the wheel clockwise into the mower housing. Do this for all wheels andensure all wheels are tightly secured.
Cutting Height Positions
Position Cutting Height
1 (lowest) 20mm
2 40mm
3 (highest) 60mm
13
CUTTING HEIGHT ADJUSTMENT
!!
123
14
MAINTENANCE
WARNING! Disconnect the mower from the power supply and ensurethe blade has stopped coasting before removing and fitting the blade.
Removing the blade (Fig. 11)
CAUTION: ALWAYS HANDLE THE BLADE WITHCARE – SHARP EDGES COULD CAUSE SERIOUSINJURY. USE GLOVES.
1. To remove the blade bolt, hold the blade firmlyand with a 13mm spanner (not supplied) loosenthe blade bolt by turning it anti-clockwise.
2. Remove the blade bolt, and blade.
3. Inspect for damage and clean as necessary.
Renew the metal blade after 50 hours mowing or 2 years whichever is the sooner – regardlessof condition. If the blade is cracked or damagedreplace it with a new one. Never use a bladebolt if the insulated head is damaged, cracked or missing.
Fitting the Blade
1. Fit the blade to the fan with the tilt edges of the blade facing towards themower, ensuring the blade is located onto the fan location points correctly.
2. Re-assemble blade bolt through blade and fan.
3. Hold the fan firmly and tighten blade bolt with a 13mm spanner, by turning ina clockwise direction. Do not over tighten.
Note: Keep all nuts, bolts and screws tight to be sure the lawn mower is in a safeworking condition.
• Check the catcher frequently for wear or deterioration.
• Replace worn or damaged parts for safety.
• Only use the replacement blade, blade bolt, and impeller specified for thisproduct.
• Be careful during adjustments of the lawn mower to prevent entrapment ofthe fingers between moving blade and fixed parts of the machine.
• Oil the wheel pins.
• Store the lawn mower in a dry place.
• Frequently check the wheel threads are firm and tight.
!!
Fig. 11
Blade Bolt
Blade
15
SPARE PARTS
Limited spare parts are available subject to availability. Please contact your localBunnings Special Orders Desk to order the required spare parts.
Most common spare parts listed below
Spare Part Part No.
Wheel SPELM300-01
Blade & Bolt SPELM300-03
Grass Catcher SPELM300-11
DESCRIPTION OF SYMBOLS
V Volts Hz Hertz
~ Alternating current W Watts
/min Revolutions or reciprocation per minute
Double insulated
no No load speed
Warning
Read the user instructions carefully to make sure you understand all the controls and what they do.
Always keep the lawnmower on the ground when mowing.Tilting or lifting the lawnmower may cause stones to be thrown out.
Keep bystanders away. Do not mow whilst people especially children or pets are in the mowing area.
Switch Off! Remove plug from mains before adjusting, cleaning or if cable is entangled or damaged. Keep the cable away from the blade.
Beware of servering toes or hands. Do not put hands or feet near a rotating blade.
Blade continues to rotate after the machine is switched off. Wait until all machine components have completely stopped before touching them.
Do not mow in the rain or leave the lawnmower outdoors while raining.
Regulator compliance mark Read operation instruction
CARING FOR THE ENVIRONMENT
16
PACK CONTENTS
Power tools that are no longer usable should not bedisposed of with household waste but in an environmentallyfriendly way. Please recycle where facilities exist. Check withyour local council authority for recycling advice.
Recycling packaging reduces the need for landfill and rawmaterials. Reuse of recycled material decreases pollution in theenvironment. Please recycle packaging where facilities exist.Check with your local council authority for recycling advice.
1 x Electric mower ELM-3002 x Handle securing bolts & knobs2 x Lower handles2 x Screws (Lower handle securing)1 x Upper handle
2 x Catcher halves4 x Wheel assembly2 x Cord clips1 x Instruction manual
17
OZITO INDUSTRIES PTY LTD
AUSTRALIA (Head Office)
1 - 23 Letcon Drive, Bangholme, Victoria, Australia 3175Telephone: 1800 069 486Facsimile: +61 3 9238 5588Website: www.ozito.com.auEmail: [email protected]
2 YEAR REPLACEMENT WARRANTY
Your product is guaranteed for a period of 24 months from the original date of purchase and is intended for DIY (Do It Yourself) use only. If a product is defective it will be replaced in accordance with the terms of this warranty. Warranty excludes consumable parts, for example: grass catcher, wheels, blade, cord clips, and all accessories..WARNING
The following actions will result in the warranty being void.
Professional, Industrial or high frequency use.If the tool has been operated on a supply voltage other than that specified on the tool.If the tool shows signs of damage or defects caused by or resulting from abuse, accidents or alterations.Failure to perform maintenance as set out within the instruction manual.If the tool is disassembled or tampered with in any way.
OZITOAustralia/New Zealand (Head Office)1-23 Letcon Drive, Bangholme, Victoria, Australia 3175
•••
••
OW8
WARRANTYYOUR WARRANTY FORM SHOULD BE RETAINED BY YOU AT ALL TIMES. IN ORDER
TO MAKE A CLAIM UNDER THIS WARRANTY YOU MUST RETURN THE PRODUCT TO YOUR NEAREST BUNNINGS WAREHOUSE WITH YOUR BUNNINGS REGISTER RECEIPT.
PRIOR TO RETURNING YOUR PRODUCT FOR WARRANTY PLEASE TELEPHONE OUR CUSTOMER SERVICE HELPLINE:
TO ENSURE A SPEEDY RESPONSE PLEASE HAVE THE MODEL NUMBER AND DATE OF PURCHASE AVAILABLE. A CUSTOMER SERVICE REPRESENTATIVE WILL TAKE YOUR CALL AND ANSWER ANY QUESTIONS YOU MAY HAVE RELATING TO THE WARRANTY POLICY
OR PROCEDURE.
The benefits provided under this warranty are in addition to other rights and remedies which are available to you at law.Our goods come with guarantees that cannot be excluded at law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure. Generally you will be responsible for all costs associated with a claim under this warranty, however, where you have suffered any additional direct loss as a result of a defective product you may be able to claim such expenses by contacting our customer service helpline above.
`Australia 1800 069 486New Zealand 0508 069 486